DTK PRM-0031I User Manual
Advertisement
Advertisement
PRM-00311
High Performance
Pentium Pro PCl Mainboard
User's Guide
Edition 1.11
©
1996 DTK Computer , Inc .
TRADEMARKS
Windows, MS-DOS, and MS Word are trademarks of Microsoft Corporation .
Novell, Netware are trademarks of Novell, Inc.
Lotus, 1 2-3, and Symphony are trademarks of Lotus Development Corporation.
PC, AT, PC-DOS, OS/2 and Presentation Manager are trademarks of ffiM
Corporation .
UNIX is the trademark of AT&T.
Intel i82440FX and Pentium Pro are registered trademark of Intel Corp .
All other brand and product names are trademarks or registered trademarks of their respective companies.
The information presented in this publication has been carefully checked for reliability; however, no responsibility is assumed for inaccuracies, whereas, specification is subjected to change without notice.
ii
CONTENTS
CHAPTERl INTRODUCTION
1.1 GENERAL SPECIFICATION l.2 MAINBOARD COMPONENTS
CHAPTER 2 MEMORY CONFIGURATION
2 .
1 SYSTEM MEMORY
5
5
CHAPTER 3 JUMPER SETTINGS AND CONNECTORS
3 .
1 SETTING THE JUMPERS
3.2 CONNECTION tHE MOTHERBOARD
3 .
2 .
1 JUMPER PRESENTATION
9
9
11
11
3 .
2 .
2 JUMPER CONVENTION OF THE MOTHERBOARD 11
3.2
.3 CONNECTOR LOCATIONS
3.3 CONNECTORS
3 .3.
1 120 - POWER SUPPLY CONNECTOR
3.3
.
2 15 IrDA CONNECTOR
3 .
3 .
3 14 - KEYLOCK CONNECTOR
3 .
3.4 12 - TURBO LED CONNECTOR
12
13
13
14
14
15
3.3.5
3
3
3
.
.
.
3
3
3
.
.
.
6
17 SPEAKER CONNECTOR
16 - HDD LED CONNECTOR
7 13 - RESET SWITCH CONNECTOR
8 118 KEYBOARD CONNECTOR
3 .
3.9 I/O CONNECTORS
3 .3.
10 117 - PS/2 STYLE KEYBOARD CONNECTOR
(OPTIONAL) 18
3.3
.
11 118 PS/2 STYLE MOUSE CONNECTOR (OPTIONAL) 18
15
16
16
17
17
3 .
3 .
12 JPl - SMI SWITCH
3 .
3 .
13 JP3 - FACTORY TESTING JUMPER
3.3.14 112 USBO CONNECTOR
3 .
4 .
15 113 - USBI CONNECTOR
3.4 GRAPHICAL DESCRIPTIONS OF JUMPER SETTINGS
3.4
.
1 CPU SPEED
21
22
19
19
20
20
1
1
4
CHAPTER 4 AMI WINBIOS SETUP
4 .
1 MOUSE SUPPORT
4.2 POINT & CLICK INTERFACE
4 .
3 USING KEYBOARD WITH WinBIOS SETUP
4.4 STARTING WinBIOS SETUP
4 .
5 WinBIOS SETUP MAIN MENU
4 .
6 SETUP
4 .
6 .
1 STANDARD SETUP
4.6.2 ADVANCED SETUP
4.6.3 CHIPSET SETUP
4 .
6.4 POWER MANAGEMENT SETUP
4 .
6 .
5 PCIIPnP SETUP
4 .
6 .
6 PERIPHERAL SETUP
4 .
7 SECURITY
4.7.1 WINBIOS PASSWORD SUPPORT
4.7.2 CHANGING A PASSWORD
4 .
7 .
3 ANTI-VIRUS
4 .8 UTILITY
4.9 DEFAULT
4.9.1 ORIGINAL
4 .
9 .
2 OPTIMAL
4 .
9.3 FAIL-SAFE
CHAPTER 5 WINBIOS POWER-ON SELF TEST
5 .
1 BEEP CODES
5.2 TROUBLESHOOTING SYSTEM PROBLEMS
5 .3 WinBIOS DISPLAYED ERROR MESSAGES
5 .
4 ISA NMI HANDLER MESSAGES iii
48
49
50
51
52
52
52
36
38
41
44
47
47
25
25
25
26
27
27
28
29
31
53
54
55
56
60
Introduction 1
CHAPTER! INTRODUCTION
The motherboard is a 4-layer, full baby AT size high-performance mainboard. It includes Intel i82440FX system chipset , NS PC87306 Super
110
controller .
1.1 GENERAL SPECIFICATION
Processor
• Intel Pentium Pro series .
• The mainboard can run with following speeds :
150, 166, 180 and 200 MHz
Chipset
• Intel 82441FX (pCI and Memory Controller)
• Intel 82442FX (Data Bus Xcelerator)
• Intel 82371SB (pCI ISA IDE Xcelerator)
• NS PC87306 (Super
110
Controller)
Main Memory
• Memory configurations from up to 384MB are possible using combination of 256K*36 to 16MB*36 SIMM module. (32Bits non-parity
72-pin SIMM Module also available).
• Support both Fast Page Mode and Extended Data Output (EDO) Mode
DRAM Modules.
• Hidden DRAM Refresh for higher system performance .
• ECC (Error Checking and Correction) support (Need SIMM module with parity) .
2 Chapter 1
Multi 110
• On board Multi-I/O supports two serial, one parallel ports and floppy drive controller.
• Serial ports are 16550 Fast UART compatible.
• Parallel port has EPP and ECP capabilities.
• IrD A supported.
• USB supported.
PCIIDE
• On board supports PCI Master IDE Controller, two connectors support up to four IDE devices such as HDD, CD ROM drive and Tape Back-up drives, etc.
• PCI Master IDE controller supports PIO Mode 3 and 4 devices, I/O data transfer rate can be up to 17Mb/s . DMA mode transfer rate can be up to
22Mb/s .
System BIOS
• AMI BIOS (128KB Flash EPROM).
Slots
• Five PCI slots (1 shared)
• Three ISA slots (1 shared)
Introduction
~~~~~----------------------------------------------
3
Board
.4 Layer
Form Factor
• Full Baby AT Size (220 x 330mm)
4
1.2
Chapter 1
MAINBOARD COMPONENTS
This section gives a brief description of key components on the mainboard .
Please refer to Fig 1 for component locations .
32BIT PC) (XPANSIDN SLOTS -.r::::...1<[YBClAF?D C
1 6 81l
-
( X PANSI ~
SLOTt rn
L.-
I--
~ ~ ~
El W
I -
...
~ ~
.
... u
Q.
'"
-
~
~~rnoo
I i
~~
I--
I-I-I-r - r - r - r - r - r -
I-l -
I ~
0; 0;
'--
~ i ~ f
0; ;;;
0;
'-L.-
' - '-a ' - l....... to
B 0
ClOC.
C,CN(rlAl[JQ c , . . ' - ' - ' - ' - c , -
EJ
~BG~EKfb',l'Hm.~ll
MAJN H(MDRY
Fig. 1 Key Components of the Mainboard
_____________________________________________________
5
CHAPTER 2 MEMORY
CONFIGURATION
2.1 SYSTEM MEMORY
The Mainboard lets user upgrade system memory via SIMM sockets on the mainboard. On-board memory is located in three banks : Bank 0, Bank 1 and Bank 2.
Two SIMM sockets are provided in each bank . User can install either 1M ,
4M,8M , 16M, 32M, 64M or 128M SIMM in each bank .
Note: The type of SIMMllSIMM2 must be
same.
The type of SIMM31SIMM4 must be same.
The type of SIMM51SIMM6 must be
same.
Table 1 provides some typical DRAM configurations supported by the mainboard.
BankO
(SIMMl,2)
IMx36 Single
None
None
IMx36 Double
None
None
Bank 1
(SIMM3,4)
Bank 2
(SIMM5,6)
None
IMx36 Single
None
None
None
None
IMx36 Double
IMx36 Single
None
None
None IMx36 Double
To be continued ..
.
Total Size
8MB
8MB
8MB
16MB
16MB
16MB
Table lA: Memory Configuration
6 Chapter 2
BankO
(SIMMl,2)
4Mx36 Single
None
None
4Mx36 Double
None
None
16Mx36 Single
None
None
16Mx36 Double
None
None
IMx36 Single
IMx36 Single
IMx36 Double
IMx36 Double
IMx36 Double
IMx36 Double
Bank I
(SIMM3,4)
None
4Mx36 Single
None
None
4Mx36 Double
None
None
16Mx36 Single
None
None
16Mx36 Double
None
Bank 2
(SIMMS, 6)
None
None
4Mx36 Single
None
None
4Mx36 Double
None
None
16Mx36 Single
None
None
16Mx36 Double
IMx36 Single
IMx36 Single
IMx36 Single
IMx36 Single
IMx36 Double
None
IMx36 Single
None
IMx36 Single
None
IMx36 Double IMx36 Double
To be continued .
.
.
Total Size
32MB
32MB
32MB
64MB
64MB
64MB
128MB
128MB
128MB
256MB
256MB
256MB
16MB
24MB
24MB
32MB
32MB
48MB
Table IB: Memory Configuration
~M~e~m~o~ryLC~onfi~l~~a~b~'o~n _____________________________________ 7
BankO
(SIMMI,2)
4Mx36 Single
4Mx36 Single
4Mx36 Single
4Mx36 Single
4Mx36 Single
4Mx36 Single
4Mx36 Double
4Mx36 Double
4Mx36 Double
4Mx36 Double
4Mx36 Double
4Mx36 Double
4Mx3 , 6 Double
4Mx36 Double
16Mx36 Single
16Mx36 Single
16Mx36 Single
16Mx36 Single
Bank I
(SIMM3,4)
IMx36 Single
IMx36 Single
IMx36 Double
IMx36 Double
4Mx36 Single
4Mx36 Single
Bank I
(SIMMS, 6)
None
IMx36 Single
None
IMx36 Double
None
4Mx36 Single
IMx36 Single
IMx36 Single
IMx36 Double
IMx36 Double
4Mx36 Single
None
IMx36 Single
None
IMx36 Double
None
4Mx36 Single 4Mx36 Single
4Mx36 Double None
4Mx36 Double 4Mx36 Double
1 Mx36 Single
IMx36 Single
None
IMx36 Single
IMx36 Double None
IMx36 Double IMx36 Double
To be continued ..
.
Total Size
40MB
48MB
48MB
64MB
64MB
96MB
72MB
80MB
80MB
96MB
96MB
128MB
128MB
192MB
136MB
144MB
144MB
160MB
Table IC: Memory Configuration
8 Chapter 2
BankO
(SIMMl,2)
16Mx36 Single
16Mx36 Single
16Mx36 Single
16Mx36 Single
16Mx36 Single l6Mx36 Single
16Mx36 Double
16Mx36 Double
16Mx36 Double
16Mx36 Double
16Mx36 Double
16Mx36 Double
16Mx36 Double
16Mx36 Double
16Mx36 Double
Bank 1
(SIMM3,4)
4Mx36 Single
4Mx36 Single
4Mx36 Double
4Mx36 Double
16Mx36 Single l6Mx36 Single lMx36 Single
1Mx36 Single
IMx36 Double
1Mx36 Double
4Mx36 Single
4Mx36 Single
4Mx36 Double
4Mx36 Double
16Mx36 Single
Table ID: Memory Configuration
Bank 2
(SIMM5,6)
None
4Mx36 Single
None
4Mx36 Double
None l6Mx36 Single
None
1Mx36 Single
None
1Mx36 Double
None
4Mx36 Single
None
4Mx36 Double
None
Total Size
160MB
192MB
192MB
256MB
256MB
384MB
264MB
272MB
272MB
288MB
288MB
320MB
320MB
384MB
384MB
9
CHAPTER 3 JUMPER
SETTINGS AND
CONNECTORS
3.1 SETTING THE JUMPERS
The table below summaries the functions and settings of each jumper of the motherboard.
CPU Speed
Selection
Function
150MHz
166MHz
Pentium Pro
Pentium Pro
To be continued ..
.
JP6:
JP7:
JP8:
JP9 :
JP6:
JP7:
JP8:
Jumper Settings
JP9: open close
1-8 close,
2-7 open,
3-6 close,
4-5 close
1-3 close,
2-4 close close open
1-8 open,
2-7 close,
3-6 close,
4-5 close
1-3 close,
2-4 open
Table 2A: Jumper Setting
lO
____________________________________________
~C~h~ap~t~er~3~
CPU Speed
Selection
Function
180MHz Pentium Pro
200MHz Pentium Pro
System ROM 5V Flash EPROM
Selection
12V Flash EPROM
Table 2B: Jumper Setting
Jumper Setting
JP6:
JP7:
JP8:
JP9 : open close
1-8 close,
2-7 open,
3-6 close,
4-5 close
1-3 open ,
2-4 close
JP6: close
JP7 : open
JP8 : 1-8 close,
2-7 open,
JP9:
3-6 close,
4-5 close
1-3 close,
2-4 open
JP4 : 2-3 close
JP4: 1-2 close
Jumper Settings and Connectors II
3.2 CONNECTION THE MOTHERBOARD
Once the mainboard have been tastened into the system case , the next step is to connect the internal cables . The internal cables are wire leads with plastic female connectors that attach to the connectors . The mainboard connectors have varying numbers of pins and are the points of contact between the mainboard and other parts of the computer.
A description of each connector and its connector pins follows. See Fig . 3 for the location of the connectors on the mainboard .
Note: Before making connectors on the board
,
make sure that power to the system is turned off.
3.2.1 JUMPER PRESENTATION
1
1
0
0
I
Pin s land 2 are s h o rt e d with a jump e r c op .
2 3
_I
Pin s 2 and 3 ar e s h o rted with a jumper co p .
2 3
Th e jumper is s h orte d when th e jumpe r c op i s pla ce d o v er th e tw o pins o f th e jump er.
The j umper is o pen when the jumper cop i s remo v ed from j umper .
3.2.2 JUMPER CONVENTION OF THE MOTHERBOARD
Different colour of jumper caps (mini-jumpers) are used on the board to represent different usage of the jumpers:
Red: CPU Clock setting
Black: Other
3.2.3 CONNECTOR LOCATIONS
I
I
I
I
I
I
1---1
I
I
I
I
I
I
I
I
I
I
I
'-_oJ
I
I
I
I
I
I
I
1---1
I
I
I
I
I
I
I
I
I
I
I
'-_oJ
I
I
I r-.,
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I t---t
I
I
I
I
I
I
I
I I
I
I
I
'-_oJ
(,-----l
I
I
I
L _____
I
I
I
I
r-l r-l r-l
I
I
I
I
I
I
I
I
I
I
I
I
I
_ J
I I I
I
I
I
I
I
I
I
L_J L_J L_J
r-l
I
I
I
I
I
I
I
I
I
I
I
I
I
L_J
I
I
I
L_J
I
I
I
I
I
I r-----""'-
~
I
I
I
I
I
L ______ -1
I
I
I
JB J9
W t.J
B B
..
JlD ..ttl
~OO ffi
J14 ~
H
"'-
J15
!i
~ .. 2 :I ~
~ ~ i!i ~ ~
~
~
I
I r
~
\
it
r--,
I
I
I
I
I
I
I
"
\
\
'--"
I
I
I
I
I
\
I
J
I
I
_ _
I
I
I
I r------...
~
I
I
I
I
L ______
I
I
(
I
I
I
I
I
,..-
-
----,
I
I
I
I
I
I
I
I
r------------..,
I
I
I
I
I
I
I
I
I
I
L ___________ _
Fig. 2 Connector Location
Jumper Settings and Connectors 13
3.3
CONNECTORS
3.3.1 J20 - POWER SUPPLY CONNECTOR
The power supply connector has two six-pin male header connectors. Plug the dual connectors from the power directly onto the board connector.
Pin
1
2
3
4
5
6
7
Description
Power. Good (Orange)
+5 VDC (Red)
+ 12 VDC (Yellow)
-12 VDC (Blue)
Ground (Black)
Ground (Black)
Ground (Black)
8
Ground (Black)
9 -5 VDC (White)
10 +5 VDC (Red)
11 +5 VDC (Red)
12 +5 VDC (Red)
Table 3: J20 - Power Supply Connector
3.3.2 J5 - IrDA CONNECTOR
J5 is a IrDA connector that use UART2 as interface of IrDA Infrared and
HP SIR.
1
D vee
@
Polarity key
o
Receiver
o
Ground
o
Transmitter
Fig. 3 J5 - IrDA Connector
3.3.3 J4 - KEYLOCK CONNECTOR
J4 is a key lock connector that enables and disables the keyboard .
D
LEO
Power
o
Not U se d o
G
roun
d
o
Keyboard Inh
ibit o r o
Ground
Fig. 4 J4 - Keyboard Connector
___________________________ 15
3.3.4 J2 - TURBO LED CONNECTOR
12 is usually connected to a Turbo LED on front of the system case . If the system board select is in Turbo mode, the indicator lights during highspeed operation. This motherboard always operate at high-speed .
[8] +
Anode
o -
Ca
th
ode
Fig. 5 J2 Turbo LED
3.3.5 J7 - SPEAKER CONNECTOR
Following is the system s~aker to connector
J7
D
Data Out
o vee o
GND
o vee
Fig. 6 J7 Speaker Connector
16 ________________________________________
~ ~C~h~ap~t~er~3~
3.3.6 J6 - HDD LED CONNECTOR
J6 is usually connected to a HDD LED on front of the system case. If
HDD is in operation, the indicator lights during operation .
D
+Anode
o
-Cathode
o
+Anode
o
-Cathode
Fig. 7 J5 HDD LED
3.3.7 J3 - RESET SWITCH CONNECTOR
Attach the Reset switch cable to this connector . The Reset switch restarts the system .
J3
I(~~)I
Description
Reset
1001
Normal (default)
Table 4: J3 Reset Switch Connector
Jumper Settings and Connectors
3.3.8 J18 - KEYBOARD CONNECTOR
A standard five-pin female DIM keyboard connector is located at the rear of the keyboard. Plug the jack on the keyboard cable into this connector.
17
Spo re 3
+5 VDC 5
Keyboard Data 2
0
0 o o
1 Keybo a rd C l ock o
4 Ground
Fig. 8 J18 - Keyboard Connector
3.3.9 110 CONNECTORS
J9
Primary IDE
Secondary IDE J8
JlO Serial Port I
JlI Serial Port 2
Jl4 Parallel Port
Jl5 FDC Connector
Table 5: Connectors Description
~C~h~aLPt~e~r
3
3.3.10 J17 - PS/2 STYLE KEYBOARD CONNECTOR
(OPTIONAL)
A PS/2 Standard six-pin female DIM connector for keyboard is located at left to 115.
2 S p o r e
4 Vcc
0
0 0
1 K eyboa r d C l o c k
0
0
3 G N D
0 0
5 Keyboard Da t a 6 Spa r e
Fig. 9 J17 - PS/2 Keyboard Connector
3.3.11 J18 - PS/2 STYLE MOUSE CONNECTOR (OPTIONAL)
A PS/2 Standard six-pin female DIM connector for mouse is located at right the 117.
4 Vc c
0 o
1 M ous e C l ock
0
0
3 G ND
0 0
5 M o use Dato 6 S p o r e
Fig. 10 J18 - PS/2 Mouse Connector
Jumper Settings and Connectors 1 9
3.3.12 JPl - SMI SWITCH
JPl is for SMI Break Switch Setting. When JPl is trigger from OPEN to
CLOSE and back to OPEN, the system would suspend immediately.
D
EXTSMI
o
Not Used
o
GND
o
EXTSMI
Fig. 11 JPl - SMI Switch
3.3.13 JP3 - FACTORY TESTING JUMPER
JP3 is for factory testing only . All the jumpers of JP3 should be opened as default.
3.3.14 J12 - USBO
CONNECTOR
A five-pin connector, located right side of IDEO, is used to connect with the
USB (Universal Serial Bus) cable . It is defined as USBO .
1
D vee
0
-Data
0
+Data
0
GND
0
Not Used
Fig. 12 USBO Connector
3.4.15 J13 - USBI
CONNECTOR
A five-pin connector, located right side of 112, is used to connect with the
USB cable. It is defined as USBI, and it's pin assignment is same as 112 .
Jumper Settings and Connectors
GRAPHICAL DESCRIPTIONS OF JUMPER
SETTINGS
1-_-1
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I I
L.._..J
I
I
I
I
....
I
-,
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
1-_-1
I
I
I
I
I
I
I
I
I
I
I
I I
L.._..J
I
I
I
I
I
I
I
I
I
I
1---1
I
I
I
I
I
I
I
I
I
I
L._..J
I
I
I
I
I
I
I
(
------,
I
I
I
I
L _____ ...J
I
I
I
I
r-, r-l r-l r-l
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I-~
I
I I
L_J
I
I
I
I
I
r-----,.
)
I
I
I
I
I
r--,r--, r-, r-,
II
II
II
II
II II I
II II I
I L...JL...J
I
"
"
"
II
II
II
I
I
I
_...JL_J
I
I
I r-,
I I r-,I I
I II
I II
I II
I II
I
I
I
I
I II
I II
I II
I II I
L_JL_J
I
I
I
/
I
., it
....
,
\
\
,
,-_
....
I
I r--,
"p,f
I
I
I
I
I
I
I
I
I
I
I
I
I
~
I
I
r------....
~
I
I
I
I
L ______ ...J
I
I
I
I r---,
I
L ___ J
I
I
BJP9
ElrTTn
'PH
Ll..1..l.I'
I
I
I
I
I
I
I
I
I
I
I
I r-------------,
r-----,
(
I
I
I
I
L _____ _ .J
I
I
I
I
I
I
21
Fig. 13 Jumper Location
22
3.4.1 CPU SPEED
1. 150MHz Pentium Pro CPU
PE NTiUM P R O CP U
2 .
Fig. 14A CPU Speed
166MHz Pentium Pro CPU
PENTIUM PRO CP U
I
Fig. 14B CPU Speed
Chapter 3
3 . 180MHz Pentium Pro CPU
4 1
J P9 fH ' I 2
~:: \ l
8 7 6 5 l g ll l
1 2 3 4 ll
JP8
PENT r UM PRO CPU
4 .
Fig. 14C CPU Speed
200MH z P e ntium Pro CPU
3
41
J P9
~ 1 2
8 7 6 5
~:~ I~I\ l lg l l l l l
1 2 3 4
J P 8
PE N T rUM P RO CPU
Fig. 14D CPU Speed
---------------------------------------------------------
25
CHAPTER 4 AMI WinBIOS SETUP
WinBIOS Setup has an easy-to-use graphical user interface that makes system configuration easy and simple. The configuration options in WinBIOS Setup are all icon-based . All settings for each option are displayed for easy access . All WinBIOS
Setup functions can be accessed by mouse , keyboard, or pen . Pen access must be customized for each hardware platform.
4.1 MOUSE SUPPORT
The following types of mouse devices are supported :
• PS/2-type mouses,
• bus mouses that use IRQs 3, 4, or 5 (IRQ2 is not supported) ,
• Microsoft-compatible mouses (the M, V, W Series using the M and M+ protocols) , and
• Logitech C-series-compatible mouses using the MM protocol.
4.2 POINT & CLICK INTERFACE
WinBIOS Setup uses the familiar point and click navigation technique .
The end user can point with the mouse anywhere on the screen, click the left mouse button , and WinBIOS Setup control is transferred to the new location . The previous window is closed .
WinBIOS Setup can be accessed via keyboard , mouse, or pen. The mouse click functions are :
• single click to change or select both global and current fields,
• double clicks to perform an operation in the selected field, and
• single click on the top left comer of any window would exit from it.
When exit from the Main Setup window , WinBIOS will prompt the user to save all changes.
All parameters that have been changed will automatically be saved, pending the selection on the exit screen .
4.3
USING KEYBOARD WITH WinBIOS SETUP
WinBIOS Setup has a built-in keyboard driver that uses simple keystroke combinations:
Keystroke
<Tab>
~ , ~ , t , J..
< Enter>
< Esc>
Function
Move to the next window or field.
Move to the next field to the right, left , above , or below .
Select in the current field .
Closes the current operation and return to previous level.
<PgUp>
< PgDn>
< Home>
< End >
< AIt > <H>
< AIt >
< Spacebar>
Returns to the previous page .
Advances to the next page.
Returns to the beginning of the text.
Advances to the end of the text.
Access a help window .
Exit WinBIOS Setup .
Alphabetic keys A to Z are used in the Virtual Keyboard, and are not case-sensitive.
Numeric keys
o
to 9 are used in the Virtual Keyboard and Numeric
Keypad .
Table 6
Award BIOS Setup Guide
2 7
4.4 STARTING WinBIOS SETUP
As POST executes , press < Del > to run WinBIOS Setup . After that the hourglass icon tells the user to wait until a process completes.
4.5
WinBIOS SETUP MAIN MENU
The WinBIOS Setup main menu , shown below , is organi z ed into four windows. Each window corresponds to a section .
Fig. 15 Main Menu
Each section contains several icons . Clicking on each icon activates a specific function. The sections are:
Setup
contains six icons that permit user to set system configuration options such as date, time, hard disk type , floppy type, and many others.
Security
Utility
contains three icons that control WinBIOS security features . contains two icons that perform system functions .
Default
contains three icons that permit user to select a group of settings for alt WinBIOS Setup options .
Each WinBIOS Setup option has two default settings. The type of defaults are :
Optimal
Fail-Safe
these settings provide the best performance characteristics. these settings are more likely to configure a workable computer when something is wrong. If user cannot boot the computer successfully , select the Fail-Safe WinBIOS setup options and try to diagnose the problem after the computer boots. These settings do not provide optimal performance .
4.6 SETUP
WinBIOS Setup can have up to six separate screens . Different types of system configuration parameters are set on each screen.
Type
Standard Setup
Advanced Setup
Chip s et Setup
Description
Set the time and date.
Configure disk drive .
Configure basic system performance p a r a meters .
Configure features specific to the chip s et used in the computer.
Power Management Setup Configure power con s ervation fe a tur es.
PCIIPnP Setup Configure PCI and Plug-and-Pla y fe a ture s.
Peripheral Setup Configure I/O support .
Table 7 : Setup Description
______________________________ __ ___ 2~
4.6.1 STANDARD SETUP
The Standard Setup screen follows .
Fig. 16 Standard Setup Menu
The following are the des c ription for the options located in the Standard Setup window.
Configuring IDE Drives: If the hard disk drive to be configured is an IDE drive, select the appropriate drive icon (pri Master, Pri Slaves, Sec Master, or Sec Slave).
Choose the Type parameter and select Auto.
AMIBIOS automatically detects the IDE drive parameters and displays them. Click on the OK button to accept these parameters.
Click on LBA/Large Mode and choose On to enable support for IDE drives with capacities greater than 528 MB .
Click on Block Mode and choose On to support IDE drives that use Block Mode.
Click on 32Bit Mode and click on On to support IDE drives that permit 32-bit accesses.
Click on PIO Mode to select the IDE Programmed 110 mode . The setting are
Auto,
0,
I, 2, 3, 4,
or
5 . Click on
Auto
to allow AMIBIOS to automatically choose the
PIO mode that the IDE drive being configured uses. If you select 0-5 you must make absolutely certain that you are selecting the PIO mode supported by the IDE drive being configured.
Date/Time Configuration: Select the Standard option. Select the Date and Time icon. The current values for each category are displayed. Enter new values through the keyboard.
Floppy Drive A:lFloppy Drive B: : Move the cursor to these fields via t and
Jand select the floppy type. The settings are
360KB 5W', 1.2MB
HI",
720KB 3W'
,
1.44MB 3W',
2.
88MB 3W'
or
Not Installed.
4.6.2 ADVANCED SETUP
The Advanced Setup options described in this section are the standard options as shown on the following screen .
Fig. 17 Advanced Setup Memu
Quick Boot: Set this option to Enabled to instruct AMIBIOS to boot quickly when the computer is powered on. The settings are:
Setting Description
Disabled AMIBIOS test all system memory. AMIBIOS waits up to 40 seconds for a READY signal from the IDE hare disk drive .
AMIBIOS waits for .5 seconds after sending a RESET signal to the IDE drive to allow the IDE drive time to get ready again.
AMIBIOS checks for a <Del> key press and runs WINBIOS
Setup if the key has been pressed.
Enabled AMIBIOS does not test system memory above I MB .
AMIBIOS does not wait up to 40 seconds for a READY signal from the IDE hard disk drive. If a READY signal is not received immediately from the IDE drive, AMIBIOS does not configure that drive. AMIBIOS does not wait for .5 seconds after sending a
RESET signal to the IDE drive to allow the IDE drive time to get ready again .
You cannot run WINBIOS Setup at system boot, because there is no delay for the Hit < Del > to run Setup message.
Table 8
The Optimal and Fail-Safe default settings are Enabled.
BootUp Sequence: This option sets the sequence of boot drives (floppy drive A:, hard disk drive C:, or a CD-ROM drive) that the AMIBIOS attempts to boot from after AMIBIOS POST completes. The setting are C:,A:.CDROM, CDROM,C:,A:.
'Jr A:. C:. CDR OM, etc. fhe default settings areA:.C:.CDROM
BootUp CPU Speed: This option lets you specify the CPU speed at system boot.
The settings are Low or High. The Optimal and Fail-Safe default settings are High.
BootUp NumLock: Set this option to OjJto tum the Num Lock key off when the computer is booted so you can use the arrow keys on both the numeric keypad and the keyboard. The settings are On or Off. The default settings are On.
Floppy Drive Swap: Set this option to Enabled to permit drives A: and B: to be swapped. The settings are Enabled or Disabled. The default settings are Disabled.
Floppy Disk Seek: Set this option to Enabled to specify that floppy drive A: will perform a seek operation at system boot. The settings are Disabled or Enabled.
The Optimal and Fail-Safe default settings are Disabled.
Mouse Support: When this option is set to Enabled, AMIBIOS supports a PS/2type mouse . The settings are Enabled or Disabled. The default settings are
Disabled.
Primary Display: This option specifies the type of display monitor and adapter in the computer. The settings are Mono. CGA4Ox25. CGA8Ox25. EGAIVGA. or
Absent. The Optimal and Fail-Safe default settings are EGAIVGA.
Password Check: This option enables password checking every time the computer is powered
0 or every time WINBIOS Setup is executed. If password prompt appears every time the computer is turned on. If Setup is chosen, the password prompt appears if WINBIOS is executed.
Parity Check: Set this option to Enabled to check the parity of all system memory.
The setting are Disabled or Enabled. The Optimal and Fail-Safe default settings are
Disabled.
OS/2 Compatible Mode: Set this option to Enabled to permit AMIBIOS to run with IDM OS/2. The settings are Enabled or Disabled. The default settings are
Disabled.
Internal Cache: This option specifies the caching algorithm used for Ll internal cache memory. The settings are :
Setting
Disabled
Description
Neither Ll internal cache memory on the CPU or L2 secondary cache memory is enabled.
WriteBack Use the write-back caching algorithm .
(default)
WriteThru Use the write-through caching algorithm.
Table 9
External Cache: This option specifies the caching algorithm used for L2 secondary
(external) cache memory. The settings are:
Setting
Disabled
Description
Neither Ll internal cache memory on the CPU or L2 secondary cache memory is enabled.
Use the write-back caching algorithm . Enabled
Table 10
Optimal default setting is Enabled. The Fail-Safe default setting is Disabled.
__A~w~a~rd~B_IO~S~S~e~tu~p_G~u~i ~ ___________________________________ 35
System BIOS Shadow Cacheable: When this option is set to Enabled, the contents of the FOOOOh system memory segment can be read from or written to L2 secondary cache memory. The contents of the FOOOOh memory segment are always copied from the BIOS ROM to system RAM for faster execution.
The settings are Enabled or Disabled . The Optimal default setting is Enabled. The
Fail-Safe default setting is Disabled.
COOO,16K Shadow/C400,16K Shadow/CSOO,16K Shadow/CCOO,16K Shadow/
DOOO,16K Shadow1D400,16K Shadow1DSOO,16K Shadow: These options control the location of the contents of the 16KB of ROM beginning at the specified memory location. If no adaptor ROM is using the named ROM area , this area is made available to the local bus. The settings are:
Setting
Enabled
Cache
Disabled
Description
The contents of COOOOh - C3FFFh are written to the same address in system memory (RAM) for faster execution.
The contents of the named ROM area are written to the same address in system memory (RAM) for faster execution, if an adaptor ROM will be using the named ROM area . Also, the contents of the RAM area can be read from and written to cache memory.
The video ROM is not copied to RAM. The contents of the video ROM cannot be read from or written to cache memory.
Table 11
The default setting is Disabled.
C __
4.6.3 CHIPSET SETUP
The Chipset Setup options described in this section are the standard options as shown on the following screen .
Fig. 18 Chipset Setup Menu
Auto Configure DRAM Timing: Specify the method of configuring DRAM timing .
Enabled Set the DRAM Timing Parameter according to th e DRAM s p ee d .
Disabled Set the DRAM Timing Parameter manuall y .
Table 12
The Optimal default setting is Enabled . The Fail-S a fe d e f a ult s e ttin g is def a ult.
DRAM Speed (ns): Specify the RAS access speed of the SIMMs installed in the motherboard as system memory . The settings are 50ns , 60ns or 70ns . The default is 70ns.
DRAM Read Burst Timing
(B/E/F):
The DRAM read burst timing depend on the type of DRAM on a per-row basis . Slower rates may be required to support slower memories . The setting are xl / 2 / 3 , x2 /2/ 3, x2 / 3 / 4 and x3 / 4 / 4 . The Optimal default setting is x2 / 3 / 4 . The Fail-Safe default setting is x3 / 4 / 4 .
DRAM Write Burst Timing (B/EIF): The DRAM write burst timing depend on the type of RAM on a per-row basis. Slower rates amy be required to support slower memories. The setting ar e x 2 / 2 / 3 , x3 / 3 / 3 , x 3 / 3 / 4 and x 4 / 4 / 4 . The Optimal default setting is x3 / 3 / 3. The Fail-Safe default setting is x4 / 4 / 4 .
RAS# To CAS# Delay: When DRAM is refreshed , both rows and columns are addressed separately. This setup item allows a delay time between the assertion of
RAS# and CAS# . The settings are Di s abl e d or Enabl e d. The Optimal and Fail -
Safe default setting is Enabled .
MA Wait State: When this option is lws , one addational wait state is inserted before the assertion of the first MA and CAS#IRAS# during DRAM read or write leadoff cycles. The affects pages hit , row miss and page miss cases . The settings are Ows or lws. The Optimal and Fail-Safe default settings are lws .
DRAM Refresh Type: This option specify the DRAM refresh type. Th e settings are CAS/RAS or RAS only . The Optimal and Fail-Safe default setting is RA S only.
DRAM Refresh Queue: When disabled , the Internal DRAM refresh queue is disabled and all refreshes are priority requests. The settings are E nabl e d and
Disabled. The Optimal and Fail-Safe settings are Enabled.
Fixed Memory Hole: Use this option to specify an area in memory that cannot be addressed on the ISA bus . The settings are Disabled , 512 640KB . or 15-16MB .
The default setting is Disabl e d .
8-Bit 110 Recovery Time: This option specifies the length of the delay (in
SYSCLKs) inserted between consecutive 8-bit I/O operations. The settings
are
I,
2,
3,
4, 5 , 6 , 7 , 8 or Disabled . The Optimal
and
Fail-Safe default settings
are
1.
16-Bit 110 Recovery Time: This option specifies the length of the delay (in
SYSCLKs) inserted between consecutive 8-bit I/O operations . The settings
are
I, 2,
3 , 4, or Disabled. The Optimal and Fail-Safe default settings are 1 .
USB Function Enabled: Set this option to Enabled to enable the USB function .
The setting are Enabled or Disabled . The default setting is Disabled.
4.6.4 POWER MANAGEMENT SETUP
The Power Management Setup options described in this
section
are the standard options as shown on the
following
screen.
~A~W~M~d~B~IO~S~Se=ru~p~G~u=id=e ___________________________________ 39
Power ManagementiAPM: Set this option to Enabled to enable the power management and APM (Advanced Power Management) features .
The settings are Enabled, 1nst-On or Disabled. The default settings are Disabled.
Instant-on Timeout: Set this option to Enabled to alow the computer to go to full power on mode when leaving a power-conserving state . This option is only available ifsupported by the computer hardware . AMIBIOS uses the RTC Alarm function to wake the computer at a prespecified time. The settings are Disabled , 1
Min , and all one minute intervals up to and including 15 Min. The default settings are Disabled.
Green PC Monitor Power State: This option specifies the power management state that the Green PC-compliant video monitor enters after the specified period of display inactivity has expired . The settings Me Off, Standby , or Suspend. The default settings Me Standby .
Video Power Down Mode: This option specifies the power management state that the video subsystem enters after the specified period of display inactivity has expired. The settings are Disabled, Standby, or Suspend . The default settings are
Standby .
Hard Disk Power Down Mode: This option specifies the power management state that the hMd disk drive enters after the specified period of display
inactivity
has expired. The settings are Disabled , Standby, or Suspend . The default settings are
Disabled.
Hard Disk Timeout (Minute): This option specifies the length of a period of hard disk inactivity. When this period expires , the hard disk drive enters the powerconserving mode specified in the Hard Disk Power Down Mode option described on the previous page . The settings Me Disabled. 1 Min(minutes), and all one minute intervals up to and including 15 Min . The default settings are Disabled.
Fig. 19 Power Management Setul) Menu
40 ________________________ ~ C~ha~p~t~er~4~
Standby Timeout (Minute): This option specifies the length of the period of system inactivity when the computer is in Full-On mode before the computer is placed in
Standby mode. In Standby mode, some power use is curtailed . The settings are
Disabled, 1 Min , 2 Min and all one minute intervals up to and including 15 Min .
The default settings are Disabled.
Suspend Timeout (Minute): This option specifies the length of the period of system inactivity when the computer is already in Standby mode before the computer is placed in Suspend mode. In Suspend mode , nearly all power use is curtailed. The settings are Disabled, 1 Min, 2 Min , and all one minute intervals up to and including 15 Min . The default settings are Disabled .
Slow Clock Ratio: This option specifies the speed at which the system clock runs in power saving modes. The settings are expressed as a ratio between the normal clock speed and the power down clock speed. The settings are 1: 1, 1: 2 (half as fast as normal, 1:4 (the normal clock speed), 1 : 8, 1 : 16, 1 : 32, 1 : 64, or 1:128 . The default setting is 1 : 8.
IRQ3IIRQ4IIRQ5IIRQ7IIRQ9IIRQIOIIRQllIIRQ12IIRQ13IIRQ14/IRQ15:
These options enable event monitoring . When the computer is in a power saving mode, activity on the named interrupt request line is monitored by AMIBIOS .
When any activity occurs, the computer enters Full On mode .
Each of these options can be set to Ignore , Monitor, Wakeup or Both . The default setting for all options is Ignore except IRQ12 is Both and IRQ 14115 are Monitor .
4.6.5 PCIIPnP SETUP
PCIlPnP Setup options are displayed by choosing the PCIlPnP Setup Icon from the Setup Menu . The standard option is shown on the following screen .
Fig. 20 PCIIPnP Setup Menu
Plug and Play Aware OS: Set this option to Yes if the operating system installed in the computer is Plug and Play-aware . AMIBIOS only detects and enables PnP ISA adapter cards that are required for system boot. The Windows 95 operating system detects and enables all other PnP-aware adapter cards. Windows 95 is PnP-aware .
Set this option to No if the operating system (such as DOS , os/i ,
Windows 3 .
x) does not use PnP . You must se t thi s o pti o n correctly or PnP-awar e adapt e r cards in s talled in y our computer will n o t b e c o nfigured properl y. The settings are N o or
Ye s. The Optimal and Fail-Safe d e fault settings are No.
PCI Latency Timer (pCI Clocks): This option sets latency of all PCI devices on the PCI bus. The settings are in units equal to PCI clocks. The settings are 32, 64,
96,128, 160, 192,224, or 248 . The Optimal and Fail-Safe default settings are 64.
PCI VGA Palette Snoop: This option must be set to Enabled if any ISA adapter card installed in the computer requires VGA palette snooping . The settings are
Disabled or Enabled. The Optimal and Fail-Safe default settings are Disabled .
PCI IDE BusMaster: Set this option to Enabled to specify that the IDE controller on the PCI local bus has bus mastering capability. The settings are Disabled or
Enabled. The Optimal and Fail-Safe default settings are Disabled.
OffBoard PCI IDE Card: This option specifies if an oftboard PCI IDE controller adapter card is used in the computer. You must also specify the PCI expansion slot on the motherboard where the oftboard PCI IDE controller card is installer. If an oftboard PCI IDE controller is used, the onboard IDE controller on the motherboard is automatically disabled. The settings are Auto, Slotl, Slot2, Slot3, Slot4, Slot5 or
Slot6.
If A uto is selected, AMIBIOS automatically determines the correct setting for this option. The Optimal and Fail-Safe default settings are Auto.
OffBoard PCI IDE Primary IRQ: This option specifies the PI interrupt used by the primary IDE channel on the oftboard PCI IDE controller. The settings are
Disabled, INTA, INTB, INTC, 1NTD, or Hardwired. The Optimal and Fail-Safe default settings are Disabled.
Ormoard PCI IDE Secondary IRQ: This option specifies the PCI interrupt used by the secondary IDE channel on the oftboard PCI IDE controller. The settings are
Disabled, INTA, INTB, INTC, INTD, or Hardwired. The Optimal and Fail-Safe default settings are Disabled.
~A~w~a~rd~B~IO~S~S~e~rn~p~G~u~i~de~___________________________________ 43
Assign IRQ to PCI VGA Card: Set this option to Yes if the PCI VGA used IRQs.
AMIBIOS will assign an IRQ to PCI VGA adapter cards. Set this option to No if the PCI VGA card do not use IRQ . The settings are Yes or No . The Optimal and
Fail-Safe default settings are Yes .
DMA Channel 0/113/5/617: These options specify the DMA Channels are used on.
These optins allow you to specify DMA Channels for use by legacy ISA adapter cards.
These options determine if AMIBIOS should remove a DMA from the pool of available DMAs passed to BIOS configurable devices. The available DMA pool is determine by reading the ESCD NVRA. If more DMAs must be removed from the pool, the end user can use these PnP setup options to remove the DMA by assigning the option to the 1SAIEISA setting. Onboard 1/0 is configurable by AMIBIOS. The
DMAs used by onboard 1/0 are configured as PnP .
The settings are PnP or lSA I ElSA. The Optimal and Fail-Safe default settings are
PnP.
IRQ3IIRQ4IIRQ5IIRQ7IIRQ9IIRQ 10lIRQ 1 llIRQ l2IIRQ 1 4IIRQ 15: These options specify the bus that the named interrupt request lines (IRQs) are used on.
These options allow you to specify IRQs for use by legacy ISA adapter cards.
These options determine if AMIBIOS should remove an IRQ from the pool of available IRQs passed to BIOS configurable devices. The available IRQ pool is determined by reading the ESCD NVRA. If more IRQs must be removed from the pool, the end user can use these PCIIPnP Setup options to remove the IRQ by assigning the option to the ISAIEISA setting. Onboard
110
is configurable by
AMIBIOS. The IRQs used by onboard
110
are configured as PCIIPnP.
The settings are PCIIPnP or lSAIEISA. The Optimal and Fail-Safe default settings are PCIIPnP.
Reserved Memory Size: This option specifies the size of the memory area reserved for legacy ISA adapter cards.
The settings are Disabled , 16K, 32K , or 64K. The Optimal and Fail-Safe default settings are Disabled.
Reserved Memory Address: This option specifies the beginning address (in hex) of the reserved memory area. The specified ROM memory area is reserved for use by legacy ISA adapter cards .
The settings are COOOO, C4000, C8000, CCOOO, DOOOO, D4000, D8000, or DCOOO.
The Optimal and Fail-Safe Default settings are COOOO.
4.6.6 PERIPHERAL SETUP
Peripheral Setup options are displayed by choosing the Peripheral Setup icon from the WINBIOS Setup main menu. All Peripheral Setup options are described in this section.
Onboard FDC: This option enables the floppy drive controller on the motherboard.
The settings are Enabled, Disabled or Auto. The Optimal and Fail-Safe default settings are Auto.
Onboard Serial PortI: This option enables serial port 1 on the motherboard and specifies the base I/O port address for serial port 1.
The settings are 3F8h, 2F8h, 3E8h, 2E8h, Disabled or Auto. The Optimal and Fail-
Safe default settings are Auto .
Onboard Serial Port2: This option enables serial port 2 on the motherboard and specifies the base 110 port address for serial port 2 .
The settings are 3F8h, 2F8h, 3E8h, 2E8h, Disabled or Auto . The Optimal and Fail-
Safe default settings are Auto.
Onboard Parallel Port: This option enables the parallel port on the motherboard and specifies the parallel port base I/O port address. The settings are 378h, 278h,
3BCh, Disabled or Auto.
The Optimal and Fail-Safe default settings are Auto.
Parallel Port Mode: This option specifies the parallel port mode . ECP and EPP are both bidirectional data transfer schemes that adhere to the IEEE P 1284 specifications.
Fig. 21 Peripheral Setup Menu
46 ________________________________________________ ~C=ha~p~t=er~4~
The settings are :
Setting
Normal
Bi-Dir
EPP
ECP
Description
The nonnal parallel port mode is used . This is the default setting .
Use this setting to support bidirectional transfers on the parallel port.
The parallel port can be used with devices that adhere to the Enhanced
Parallel Port (EPP) specification . EPP uses the existing parallel port signals to provide asymmetric bidirectional data transfer driven by the host device .
The parallel port can be used with devices that adhere to the Extended
Capabilities Port (ECP) specification . ECP uses the DMA protocol to achieve transfer rates of approximately 2.5 Mbs . ECP provides symmetric bidirectional communications.
Table 13
Parallel Port
IRQ: This option is only available if the setting for the Onboard
Parallel Port option is a 378h, 278h or 3BCh . The settings are 5 or 7.
Parallel Port DMA Channel:
This option is only available if the setting for the
Parallel Port Mode
option is ECP . The settings are 0, J, or 3 .
Onboard rDE:
This option specifies the onboard IDE controller channels that will be used. The settings are Primary , Secondary , Both, or Disabled . The Optimal and
Fail-Safe default settings are Both .
4.7
SECURITY
4.7.1 WINBIOS PASSWORD SUPPORT
WINBIOS Setup has an optional password feature . The system can be configured so that all users must enter a password every time the system boots or when WINBIOS Setup is executed . You can set either a Supervisor password or a User password .
If You Do Not Want to Use a Password
Just press < Enter > when the password prompt appears.
The password check option is enabled in Advanced Setup
by
choosing either Always (the password prompt appears every time the system is powered on) or S e tup (the password prompt appears only when WINBIOS is run) . The password is stored in CMOS RAM . The following screen appears when you select the password icon from the WINBIOS Setup main menu :
Fig. 22 Password Input Menu
You can enter a password by:
• typing the password on the keyboard,
• selecting each letter via the mouse, or
• selecting each letter via the pen stylus.
Pen access must be customized for each specific hardware platform!
When you select Supervisor or User, AMIBIOS prompts for a password.
You must set the Supervisor password before you can set the User password.
Enter a 1 - 6 character password. The password does not appear on the screen when typed. Make sure you write it down. If drain CMOS RAM and reconfigure the system .
4.7.2 CHANGING A PASSWORD
Select the Password icon (Supervisor or User) from the Security section of the WinBIOS Setup main menu. Enter the password and press <Enter>.
The screen does not display the characters entered . After the new password is entered, retype the new password as prompted and press <Enter>. If the password confirmation is incorrect, an error message appears. If the new password is entered without error, press <Esc> to return to the WinBIOS
Setup Main Menu. The password is stored in CMOS RAM after WinBIOS
Setup completes. The next time the system boots, user is prompted for password if
~A~w~a=rd~B~IO~S~S~et~u~p~G~u=i~de~___________________________________ 49
4.7.3 ANTI-VIRUS
When the Anti-Virus icon is selected from the Security section of the
WinBIOS Setup main menu, WinBIOS issues a warning when any program
(or virus) issues a Disk Format command or attempts to write to the boot sector of the hard disk drive. The following screen appears when user select the Anti-Virus icon:
Fig. 23 Anti Virus Menu
The settings are Enabled or Disabled. If enabled, the following appears when a write is attempted to the boot sector. User may have to type N several times to prevent the boot sector write.
Boot Sector write!!! possible VIRUS: continue (YIN)?
The following is displayed after any attempt to format any cylinder, head, or sector of any hard disk drive via the BIOS INT 13 Hard Disk Drive Service:
Format! ! ! possible VIRUS: continue (YIN)?
If the anti-virus feature is Enabled, a virus warning message will be displayed when user attempt to format the hard disk drive .
If user select Continue, formatting proceeds as normal.
4.8 UTILITY
The following icons appear in this section:
• Color set, and
• Language.
Award BIOS Setup Guide
------------~~-----------------------------------------
51
Color Set
Color Set sets the WINBIOS Setup screen colors .
Fig. 24 Color Set Menu
Language
Language allows you to select English, German, or French language screen prompts and messages . This BIOS is a English version.
4.9
DEFAULT
The icons in this section permit user to select a group of settings for all
WinBIOS Setup options . Not only can use these icons to quickly set system configuration parameters , user can choose a group of settings that have a better chance of working when the system is having configuration-related problems.
52 Chapter 4
4.9.1 ORIGINAL
Choose the Original icon to return to the system configuration values present in WinBIOS Setup when user first began this WinBIOS Setup session .
4.9.2 OPTIMAL
User can load the optimal default settings for the WinBIOS Setup options by selecting the Optimal icon . The Optimal default settings are best-case values that should optimize system performance . If CMOS RAM is corrupted, the Optimal settings are loaded automatically .
4.9.3 FAIL-SAFE
User can load the Fail-Safe WinBIOS Setup option settings by selecting the
Fail-Safe icon from the Default section of the WinBIOS setup main menu .
The Fail-Safe settings provide far from optimal system performance, but are the most stable settings . Use this option as a diagnostic aid if the system is behaving erratically .
WinBIOS Power-On Self Test 53
CHAPTER 5 WinBIOS POWER-ON
SELF TEST
WinBIOS provides all IBM standard Power-On Self Test (POST) routines as well as enhanced WinBIOS POST routines . WinBIOS POST supports CPU internal diagnostics .
Everytime the system is powered on , WinBIOS executes two types of POST routines :
System Test and Initialization (test and initialize WinBIOS for normal operations) , and
System Configuration Verification (compare defined configuration with hardware actually installed) .
BIOS error are reported in one of two ways : the error occurs before the display device is initialized, the error occurs after the display device is initialized, then ... a series of beeps sound . Beep codes indicate that a fatal error has occurred . WinBIOS Beep Codes are described on the nest page. the error message is displayed.
WinBIOS error messages are explained in "WinBIOS Displayed
Error Message" section. A prompt to press <Fl> can appear with displayed error messages.
Table 14
54 ________________________________________________
C==ha~Pct~er~5~
5.1 BEEP CODES
Fatal errors. which halt the boot process, are communicated through a series of audible beeps. IfWinBIOS POST can initialize the system video display, it displays the error message. Displayed error messages, in most cases, allow the system to continue to boot.
Beeps
1
2
3
4
5
6
7
8
9
10
II
Error message
Refresh Failure
Parity Error
Base 64MB Memo!)' Failure
Timer Not Operational
Processor error
8042 - Gate A20 Failure
Processor Exception Interrupt Error
Display Memo!)' Read/Write Error
ROM checksum Error
CMOS Shutdown Register
Read/Write Error
Cache Memo!)' bad - do not enable cache
Description
The memo!)' refresh circuitry is faulty .
Parity error in the base memo!)' (the first 64KB block) of memo!)'.
Memo!)' failure in first 64KB.
A memo!)' failure in the ftrst 64KB of memo!)" or Timer 1 is not functioning.
The CPU generated an error.
Cannot switch to protected mode.
The CPU on the CPU Card generated an exception interrupt.
The system video adapter is either mi ss ing or its memo!)' is faulty . This is not a fatal error.
The ROM checksum value does not match the value encoded in WinBIOS.
The shutdown register for CMOS RAM has failed.
The cache memo!)' test failed . Cache memo!)' is disabled. Do n o t press < Ctrl > < Alt >
< Shift > < + > to enab le cache mem ory.
Table 15: WinBIOS Beep Codes
__ 55
5.2
TROUBLESHOOTING SYSTEM PROBLEMS
The following table shows what is needed to do when the computer has a
WinBIOS and it starts beeping:
1,2, or 3 times
6 times
8 times
...
...
9 times ...
11 times ...
...
4, 5, 7, or 10 times ... then ••. reseat the memory SIMMs or DIPs. If the system still beeps, replace the memory. reseat the keyboard controller chip. If it still beeps, replace the keyboard controller. If it still beeps, try a different keyboard, or replace the keyboard fuse, if the keyboard has one. there is a memory error on the video adapter .
Replace the video adapter, or the RAM on the video adapter. the BIOS ROM chip is bad. The system probably needs a new BIOS ROM chip. reseat the cache memory on the motherboard . If it still beeps, replace the cache memory. the motherboard must be replaced .
Table 16
5.3 WinBIOS DISPLAYED ERROR MESSAGES
If an error occurs after the system display has been initialized, the error message are displayed as follows :
ERROR Message Line 1
ERROR Message Line 2
Press
<Fl>
to continue
and the system halts. The system does not halt if "Wait For <Fl> If Any
Error" in Advanced Setup is "Disabled".
RUN SETUP UTILITY.
may also appear. Press <Fl> to run WinBIOS Setup if this message appears.
Error Message
8042 Gate-A20 Error
Address Line Short!
C: Drive Error
C: Drive Failure
Cache Memory Bad,
Do Not Enable Cache!
CH-2 Timer Error
Explanation
Gate A20 on the keyboard controller (8042) is not working. Replace the 8042.
Error in the address decoding circuitry.
No response from drive C: . Run the AMIDiag
Hard Disk Utility. Check the C: hard disk type in
Standard Setup.
No response from hard disk drive C:. Replace the drive .
Cache memory is defective. Run AMIDiag.
An AT system has two timers in timer2 .
To be continued .
..
. There is an error
Table 17A
Error Message Explanation
CMOS Battery State Low
CMOS Checksum Failure
CMOS RAM is powered by a battery . The battery power is low. Replace the battery.
CMOS RAM checksum is different than the previous value . Run WinBIOS Setup .
CMOS System Options Not Set The values stored in CMOS RAM are either corrupt or nonexistent. Run WinBIOS
Setup.
CMOS Display Type Mismatch The video type in CMOS RAM does not match the type detected . Run WinBIOS
Setup .
CMOS Memory Size Mismatch The amount of memory found by WinBIOS is different than the amount in CMOS
RAM. Run WinBIOS Setup.
CMOS Time & Date Not Set
D : Drive Error
Run Standard setup to set the date and time.
No response from Drive D:. Run the
AMIDiag Hard Disk Utility. Check the hard disk type in Standard Setup .
D: Drive Failure No response from hard disk drive D:.
Replace the drive .
Diskette Boot Failure
Display Switch Not Proper
The boot diskette in drive A: cannot be used to boot the system . Use another boot diskette and follow the screen instructions.
Some systems require a video switch be set to either color or monochrome. Turn the system off, set the switch properly, then power on.
To be continued ...
Table 17B
Error Message
DMAError
DMA 1 Error
DMA 2 Error
Explanation
Error in the DMA controller .
Error in the first DMA channel.
Error in the second DMA channel.
FDD Controller Failure WinBIOS cannot communicate with the floppy disk drive controller. Check all appropriate connections after the system is powered down.
HDD Controller Failure WinBIOS cannot communicate with the hard disk drive controller. Check ail appropriate connections after the system is powered down.
INTRl Error
INTR2 Error
Invalid Boot Diskette
Interrupt channel 1 failed POST.
Interrupt channel 2 failed POST .
WinBIOS can read the diskette in floppy drive A :, but it cannot boot the system with it. Use another boot diskette and follow the screen instructions .
Keyboard Is Locked ...
Unlock It
Keyboard Error
The keyboard lock on the system is engaged . The system must be unlocked to continue to boot.
KBlInterface Error
No ROM BASIC
The keyboard has a timing problem. Make sure a
Keyboard Controller WinBIOS is installed . Set
"Keyboard" in "Advanced Setup" to "Not Installed" to skip the keyboard POST routines.
There is an error in the keyboard connector .
Cannot find a proper bootable sector on either drive
A:
or C: . WinBIOS cannot find ROM Basic .
To be continued ...
Table 17C
Error Message
Off Board Parity Error
On Board Parity Error
Parity Error ????
Explanation
Parity error in memory installed on an adapter card in an expansion slot. Format is :
OFF BOARD PARITY ERROR ADDR
= (XXXX)
XXXX is the hex address where the error occurred.
Run AMlDiag to find and correct memory problems .
Parity error in motherboard memory . Format is :
ON BOARD PARITY ERROR ADDR
= (XXXX)
XXXX is the hex address where the error occurred .
Run AMlDiag to find and correct memory problems.
Parity error in system memory at an unknown address. Run AMlDiag to find and correct memory problems.
Table 17D
5.4 ISA NMI HANDLER MESSAGES
ISA NMI
Message
Explanation
Memory Parity Error Memory failed.
If
the memory location can be at xxxxx determined, it is displayed as xxxxx.
If
not, the message is Memory Parity Error ????
110 Card Parity Error
An
expansion card failed.
If
the address can
be
at xxxxx determined, it is displayed as xxxxx. If not, the message is 110 Card Parity Error ????
DMA Bus Time-Out A device has driven the bus signal for more than 7
.
8 microseconds
.
Table 18
WinBIOS Power-On Self Test
----~~~~~~~~---------------------------
61
Download
Advertisement