D-Link DSL-2640U Quick Installation Manual

Quick Installation Guide

DSL-2640U

Wireless ADSL2+ Router with Ethernet WAN Support

DSL-2640U Quick Installation Guide

BEFORE YOU BEGIN

Delivery Package

• Router DSL-2640U

• Power adapter DC 12V/0.5A

• RJ-11 telephone cable

• Straight-through Ethernet cable

• Splitter

• “ Quick Installation Guide ” (brochure).

If any of the items are missing, please contact your reseller.

The “ User Manual ” and “ Quick Installation Guide ” documents are available on D-Link website (see www.dlink.ru

).

!

Using a power supply with a different voltage rating than the one included will cause damage and void the warranty for this product.

2

DSL-2640U Quick Installation Guide

Default Settings

IP address of wireless router 192.168.1.1

Username (login) admin

Password admin

Name of wireless network (SSID) DSL-2640U

Network key (PSK) see WPS PIN on the barcode label on the bottom panel of the device

3

DSL-2640U Quick Installation Guide

System Requirements and Equipment

• A computer with any operating system that supports a web browser.

• A web browser to access the web-based interface of the router:

◦ Apple Safari 8 and later

◦ Google Chrome 48 and later

◦ Microsoft Internet Explorer 10 and later

◦ Microsoft Edge 20.10240 and later

◦ Mozilla Firefox 44 and later

◦ Opera 35 and later.

• A NIC (Ethernet or Wi-Fi adapter) to connect to the router.

• An 802.11b, g, or n Wi-Fi adapter to create a wireless network.

4

DSL-2640U Quick Installation Guide

CONNECTING TO PC

PC with Ethernet Adapter

1. Make sure that your PC is powered off.

2. Connect an Ethernet cable between any of four Ethernet ports located on the back panel of the router and the Ethernet port of your PC.

3.

To connect the router to a DSL line: connect a phone cable between the

DSL port of the router and the ADSL OUT port of the splitter. Connect your phone to the PHONE port of the splitter. Then connect another phone cable between a phone jack and the ADSL IN port of the splitter.

4.

To connect the router to an Ethernet line: run the Initial Configuration

Wizard and select the router's LAN port that will be used as the WAN port. Then connect the Ethernet cable between the selected Ethernet port located on the back panel of the router and the Ethernet line.

5. Connect the power cord to the power connector port on the back panel of the router, then plug the power adapter into an electrical outlet or power strip.

6. Turn on the router by pressing the ON/OFF button on its back panel.

7. Turn on your PC and wait until your operating system is completely loaded.

Now you should configure your PC to obtain an IP address automatically (as

DHCP client).

5

DSL-2640U Quick Installation Guide

Obtaining IP Address Automatically in OS Windows XP

1. Click the Start button and proceed to the Control Panel > Network and Internet Connections > Network Connections window.

2. In the Network Connections window, right-click the relevant Local

Area Connection icon and select the Properties line in the menu displayed.

3. In the Local Area Connection Properties window, on the General tab, select the Internet Protocol (TCP/IP) line. Click the Properties button.

6

DSL-2640U Quick Installation Guide

4. Select the Obtain an IP address automatically and Obtain DNS server address automatically radio buttons. Click the OK button.

5. Click the ОК button in the connection properties window.

Now your computer is configured to obtain an IP address automatically.

7

DSL-2640U Quick Installation Guide

Obtaining IP Address Automatically in OS Windows 7

1. Click the Start button and proceed to the Control Panel window.

2. Select the Network and Sharing Center section. (If the Control Panel has the category view (the Category value is selected from the View by drop-down list in the top right corner of the window), choose the View network status and tasks line under the Network and Internet section.)

3. In the menu located on the left part of the window, select the Change adapter settings line.

4. In the opened window, right-click the relevant Local Area Connection icon and select the Properties line in the menu displayed.

5. In the Local Area Connection Properties window, on the

Networking tab, select the Internet Protocol Version 4 (TCP/IPv4) line. Click the Properties button.

8

DSL-2640U Quick Installation Guide

6. Select the Obtain an IP address automatically and Obtain DNS server address automatically radio buttons. Click the OK button.

7. Click the OK button in the connection properties window.

Now your computer is configured to obtain an IP address automatically.

9

DSL-2640U Quick Installation Guide

PC with Wi-Fi Adapter

1.

To connect the router to a DSL line: connect a phone cable between the

DSL port of the router and the ADSL OUT port of the splitter. Connect your phone to the PHONE port of the splitter. Then connect another phone cable between a phone jack and the ADSL IN port of the splitter.

2.

To connect the router to an Ethernet line: run the Initial Configuration

Wizard and select the router's LAN port that will be used as the WAN port. Then connect the Ethernet cable between the selected Ethernet port located on the back panel of the router and the Ethernet line.

3. Connect the power cord to the power connector port on the back panel of the router, then plug the power adapter into an electrical outlet or power strip.

4. Turn on the router by pressing the ON/OFF button on its back panel.

5. Turn on your PC and wait until your operating system is completely loaded.

6. Turn on your Wi-Fi adapter. As a rule, modern notebooks with built-in wireless NICs are equipped with a button or switch that turns on/off the wireless adapter (refer to your PC documents). If your PC is equipped with a pluggable wireless NIC, install the software provided with your

Wi-Fi adapter.

Now you should configure your Wi-Fi adapter.

10

DSL-2640U Quick Installation Guide

Configuring Wi-Fi Adapter in OS Windows XP

1. Click the Start button and proceed to the Control Panel > Network and Internet Connections > Network Connections window.

2. Select the icon of the wireless network connection and make sure that your Wi-Fi adapter is on.

3. Search for available wireless networks.

4. In the opened Wireless Network Connection window, select the wireless network DSL-2640U and click the Connect button.

5. In the opened window, enter the network key (see WPS PIN on the barcode label on the bottom panel of the device) in the Network key and

Confirm network key fields and click the Connect button.

After that the Wireless Network Connection Status window appears.

!

If you perform initial configuration of the router via Wi-Fi connection, note that immediately after changing the wireless default settings of the router you will need to reconfigure the wireless connection using the newly specified settings.

11

DSL-2640U Quick Installation Guide

Configuring Wi-Fi Adapter in OS Windows 7

1. Click the Start button and proceed to the Control Panel window.

2. Select the Network and Sharing Center section. (If the Control Panel has the category view (the Category value is selected from the View by drop-down list in the top right corner of the window), choose the View network status and tasks line under the Network and Internet section.)

3. In the menu located on the left part of the window, select the Change adapter settings line.

4. In the opened window, select the icon of the wireless network connection and make sure that your Wi-Fi adapter is on.

5. To open the list of available wireless networks, select the icon of the wireless network connection and click the Connect To button or leftclick the network icon in the notification area located on the right side of the taskbar.

12

DSL-2640U Quick Installation Guide

6. In the opened window, in the list of available wireless networks, select the wireless network DSL-2640U and click the Connect button.

!

7. In the opened window, enter the network key (see WPS PIN on the barcode label on the bottom panel of the device) in the Security key field and click the OK button.

8. Wait for about 20-30 seconds. After the connection is established, the network icon will be displayed as the signal level scale.

If you perform initial configuration of the router via Wi-Fi connection, note that immediately after changing the wireless default settings of the router you will need to reconfigure the wireless connection using the newly specified settings.

13

DSL-2640U Quick Installation Guide

CONFIGURING ROUTER

Connecting to Web-based Interface

Start a web browser. In the address bar of the web browser, enter the IP address of the router (by default, the following IP address is specified:

192.168.1.1

). Press the Enter key.

!

If the error “ The page cannot be displayed ” (or “ Unable to display the page ”/“ Could not connect to remote server ”) occurs upon connecting to the web-based interface of the router, make sure that you have properly connected the router to your computer.

If the device has not been configured previously or the default settings have been restored, after access to the web-based interface the Initial Configuration

Wizard opens (see the Initial Configuration Wizard section, page 18).

14

DSL-2640U Quick Installation Guide

If you configured the device previously, after access to the web-based interface the login page opens. Enter the username ( admin ) in the Username field and the password you specified in the Password field, then click the LOGIN button.

The web-based interface of the router is bilingual (English/Russian). You can select the needed language upon the initial configuration of the web-based interface of the router or in the System / Configuration section of the menu.

15

DSL-2640U Quick Installation Guide

The Summary page displays general information on the router and its software.

16

DSL-2640U Quick Installation Guide

The Home page displays links to the most frequently used pages with device's settings.

Other settings of the router are available in the menu in the left part of the page. Go to the relevant section and select the needed page or run the wizard in the Initial Configuration section.

17

DSL-2640U Quick Installation Guide

Initial Configuration Wizard

In order to start the Initial Configuration Wizard manually, go to the Initial

Configuration section.

Click the OK button and wait until the factory default settings are restored.

Then click the START button.

If the device has not been configured previously or the default settings have been restored, the Initial Configuration Wizard starts automatically upon access to the web-based interface or upon opening a web site on the Internet.

1. Click YES in order to leave the current language of the web-based interface or click NO to select the other language.

2. On the next page, click the CONTINUE button.

18

DSL-2640U Quick Installation Guide

Selecting Operation Mode

In order to connect your device to an ADSL line, on the Device mode page, from the Connection method list, select the ADSL value. In this mode you can configure a WAN connection, set your own settings for the wireless network, configure LAN ports to connect an STB or VoIP phone, and set your own password for access to the web-based interface of the device.

In order to connect your device to an Ethernet line, on the Device mode page, from the Connection method list, select the Ethernet value. In this mode you can configure a LAN port as a WAN port, configure a WAN connection, set your own settings for the wireless network, configure LAN ports to connect an STB or VoIP phone, and set your own password for access to the web-based interface of the device.

When the operation mode is selected, click the NEXT button.

19

DSL-2640U Quick Installation Guide

Selecting Ethernet WAN Port

This configuration step is available for the Ethernet connection method.

1.

On the Device connection page, select a LAN port that will be used as the WAN port.

2. Click the NEXT button.

20

DSL-2640U Quick Installation Guide

Configuring Ethernet WAN Connection

!

You should configure your WAN connection in accordance with data provided by your Internet service provider (ISP). Make sure that you have obtained all necessary information prior to configuring your connection.

Otherwise contact your ISP.

1. On the Internet connection type page, from the Connection type list, select the connection type used by your ISP and fill in the fields displayed on the page.

Static IPv4: Fill in the following fields: IP address , Netmask , Gateway IP address , and DNS IP address .

Static IPv6: Fill in the following fields: IP address , Prefix , and Gateway

IP address .

21

DSL-2640U Quick Installation Guide

PPPoE, IPv6 PPPoE, PPPoE Dual Stack: Enter authorization data provided by your ISP (the username (login) in the Username field and the password in the Password field). Click the Show icon ( ) to display the entered password. If authorization is not required, select the Without authorization checkbox.

2.

If your ISP uses MAC address binding, select the Clone MAC address of your device checkbox.

3.

If the Internet access is provided via a VLAN channel, select the Use

VLAN checkbox and fill in the VLAN ID field.

4.

Click the NEXT button.

22

DSL-2640U Quick Installation Guide

Configuring ADSL WAN Connection

!

You should configure your WAN connection in accordance with data provided by your Internet service provider (ISP). Make sure that you have obtained all necessary information prior to configuring your connection.

Otherwise contact your ISP.

1. On the Internet connection type page, from the Connection type list, select the connection type used by your ISP and fill in the fields displayed on the page.

Static IPv4, IPoA: Fill in the following fields: IP address , Netmask ,

Gateway IP address , and DNS IP address .

Static IPv6: Fill in the following fields: IP address , Prefix , and Gateway

IP address .

23

DSL-2640U Quick Installation Guide

PPPoE, IPv6 PPPoE, PPPoE Dual Stack, PPPoA: Enter authorization data provided by your ISP (the username (login) in the Username field and the password in the Password field). Click the Show icon ( ) to display the entered password. If authorization is not required, select the Without authorization checkbox.

2.

Specify the VPI and VCI values in the relevant fields.

3.

Click the NEXT button.

24

DSL-2640U Quick Installation Guide

Configuring Wireless Network

1. On the Wireless Network 2.4 GHz page, in the Network name field, specify your own name for the wireless network or leave the value suggested by the router.

2. In the Password field, specify your own password for access to the wireless network or leave the value suggested by the router (WPS PIN of the device, see the barcode label).

3. You can restore the parameters of the wireless network specified before resetting to factory defaults. To do this, click the RESTORE button.

25

DSL-2640U Quick Installation Guide

4. If you want to create an additional wireless network isolated from your

LAN, select the Enable guest network checkbox.

5. In the Network name field, specify your own name for the guest wireless network or leave the value suggested by the router.

6. If you want to create a password for access to the guest wireless network, deselect the Open network checkbox and fill in the Password field.

7. If you want to limit the bandwidth of the guest wireless network, select the Enable shaping checkbox and fill in the Shaping field.

8. Click the NEXT button.

26

DSL-2640U Quick Installation Guide

Configuring LAN Ports for IPTV/VoIP

1. On the IPTV page, select the Is an STB connected to the device checkbox.

2. Select a free LAN port for connecting your set-top box.

3.

For the Ethernet connection method : If the IPTV service is provided via a VLAN channel, select the Use VLAN ID checkbox and fill in the

VLAN ID field.

4.

For the ADSL connection method : Specify the VPI and VCI values in the relevant fields.

5. Click the NEXT button.

27

DSL-2640U Quick Installation Guide

6. On the VoIP page, select the In an IP phone connected to the device checkbox.

7. Select a free LAN port for connecting your IP phone.

8.

For the Ethernet connection method : If the VoIP service is provided via a VLAN channel, select the Use VLAN ID checkbox and fill in the

VLAN ID field.

9.

For the ADSL connection method : Specify the VPI and VCI values in the relevant fields.

10.

Click the NEXT button.

28

DSL-2640U Quick Installation Guide

Changing Web-based Interface Password

On this page you should change the default administrator password. You may set any password except admin . Use digits, Latin letters (uppercase and/or lowercase), and other characters available in the US keyboard layout.

1

!

Remember or write down the new password for the administrator account. In case of losing the new password, you can access the settings of the router only after restoring the factory default settings via the hardware RESET button. This procedure wipes out all settings that you have configured for your router.

Click the NEXT button.

On the next page, check all the settings you have just specified.

Also you can save a text file with parameters set by the Wizard to your PC. To do this, click the SAVE CONFIGURATION FILE button and follow the dialog box appeared.

To finish the Wizard, click the APPLY button. The router will apply settings, reboot, if needed, and check the Internet connection if the Wizard has configured a WAN connection.

1 0-9, A-Z, a-z, space, !"#$%&'()*+,-./:;<=>?@[\]^_`{|}~.

29

DSL-2640U Quick Installation Guide

Configuring Local Area Network

1.

Go to the Connections Setup / LAN page.

2.

If needed, change the IPv4 address of the router's LAN interface and the mask of the local subnet. To do this, click the IPv4 tab and specify needed values in the IP address and Subnet mask fields in the IP section.

3.

If needed, specify your own IPv6 address of the router's LAN interface.

To do this, click the IPv6 tab and select the Static value from the

Addressing Mode drop-down list in the IP section. Then specify the needed value in the IP address field.

30

DSL-2640U Quick Installation Guide

4.

IPv4 address assignment . By default, the built-in DHCP server of the router assigns IPv4 addresses to the devices of the LAN. If you want to manually assign IPv4 addresses, disable the DHCP server (click the

IPv4 tab and select the Disable value from the Mode drop-down list in the DHCP section).

5.

IPv6 address assignment . By default, the devices of the LAN automatically assign IPv6 addresses to themselves (the Stateless value is selected from the Autoconfiguration mode drop-down list in the

DHCP section on the IPv6 tab). If the devices of the LAN do not support

IPv6 address autoconfiguration, enable the built-in DHCPv6 server of the router (select the Stateful value from the Autoconfiguration mode drop-down list). If you want to manually assign IPv6 addresses to devices of the LAN, select the Disable value from the Mode drop-down list.

6.

After specifying the needed parameters on the Connections Setup /

LAN page, click the APPLY button.

31

DSL-2640U Quick Installation Guide

SPECIFICATIONS

*

Hardware

Processor

RAM

Flash

Interfaces

LEDs

Buttons

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

Antenna

Power connector ·

·

RTL8676S (450MHz)

32 MB, SDRAM

8 MB, SPI

RJ-11 DSL port

4 10/100BASE-TX LAN ports

POWER

4 LAN LEDs

WLAN

WPS

DSL

INTERNET

ON/OFF button to power on/power off

RESET button to restore factory default settings

WPS button to set up wireless connection

WIRELESS ON/OFF button to enable/disable wireless network

External non-detachable omnidirectional antenna (2dBi gain)

Power input connector (DC)

* The device features are subject to change without notice. For the latest versions of the firmware and relevant documentation, visit www.dlink.ru

.

32

DSL-2640U

DSL Parameters

ADSL Standards

Quick Installation Guide

ATM/PPP Protocols

·

·

·

·

·

·

·

·

·

·

·

· ADSL: Multi-mode, ANSI T1.413 Issue 2, ITU-T G.992.1

(G.dmt) Annex A, ITU-T G.992.2 (G.lite) Annex A, ITU-T

G.994.1 (G.hs)

ADSL2: ITU-T G.992.3 (G.dmt.bis) Annex A/L/M, ITU-T

G.992.4 (G.lite.bis) Annex A

ADSL2+: ITU-T G.992.5 Annex A/L/M

Bridged and routed Ethernet encapsulation

VC-based or LLC-based multiplexing

ATM Forum UNI3.1/4.0 PVC (up to 8 PVCs)

ATM Adaptation Layer Type 5 (AAL5)

ITU-T I.610 OAM F4/F5 loopback

ATM QoS

PPP over ATM (RFC 2364)

PPP over Ethernet (PPPoE)

Keep-alive for PPP connections

Software

WAN connection types

Network functions

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

PPPoA

PPPoE

IPv6 PPPoE

PPPoE Dual Stack

IPoA

Static IPv4 / Dynamic IPv4

Static IPv6 / Dynamic IPv6

Bridge

DHCP server/relay

Stateful/Stateless mode for IPv6 address assignment, IPv6 prefix delegation

DNS relay

Dynamic DNS

Static IP routing

Static IPv6 routing

IGMP Proxy

IGMP snooping

RIP

Support of UPnP IGD

Support of VLAN

WAN ping respond

Support of SIP ALG

Support of RTSP

33

DSL-2640U Quick Installation Guide

Software

Firewall functions

VPN

QoS

Management

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

·

Network Address Translation (NAT)

Stateful Packet Inspection (SPI)

IP filter

IPv6 filter

MAC filter

URL filter

DMZ

Prevention of ARP and DDoS attacks

Virtual servers

Built-in Yandex.DNS web content filtering service

IPSec/PPTP/L2TP/PPPoE pass-through

Interface grouping

VLAN priority (802.1p)

Local and remote access to settings through TELNET/WEB

(HTTP/HTTPS)

Bilingual web-based interface for configuration and management (Russian/English)

Firmware update via web-based interface

Automatic notification on new firmware version

Saving/restoring configuration to/from file

Support of remote logging

Automatic synchronization of system time with NTP server and manual time/date setup

Ping function

Traceroute utility

TR-069 client

Wireless Module Parameters

Standards

Frequency range

Wireless connection security

Advanced functions

·

·

·

·

·

·

·

·

·

·

·

· IEEE 802.11b/g/n

2400 ~ 2483.5MHz

WEP

WPA/WPA2 (Personal)

МАС filter

WPS (PBC/PIN)

WMM (Wi-Fi QoS)

Information on connected Wi-Fi clients

Advanced settings

Guest Wi-Fi / support of MBSSID

Limitation of wireless network rate

Periodic scan of channels, automatic switch to least loaded channel

34

DSL-2640U Quick Installation Guide

Wireless Module Parameters

Wireless connection rate

·

·

·

IEEE 802.11b: 1, 2, 5.5, and 11Mbps

IEEE 802.11g: 6, 9, 12, 18, 24, 36, 48, and 54Mbps

IEEE 802.11n: from 6.5 to 150Mbps (from MCS0 to MCS7)

Transmitter output power · 802.11b (typical at room temperature 25 °C)

18dBm

· 802.11g (typical at room temperature 25 °C)

15.5dBm

The maximum value of the transmitter output power depends upon the radio frequency regulations applied in your country

Receiver sensitivity ·

· 802.11n (typical at room temperature 25 °C)

14dBm

802.11b (typical at room temperature 25 °C)

-82dBm at 1Mbps

-80dBm at 2Mbps

-78dBm at 5.5Mbps

-76dBm at 11Mbps

·

·

802.11g (typical at room temperature 25 °C)

-85dBm at 6Mbps

-84dBm at 9Mbps

-82dBm at 12Mbps

-80dBm at 18Mbps

-77dBm at 24Mbps

-73dBm at 36Mbps

-69dBm at 48Mbps

-68dBm at 54Mbps

802.11n (typical at room temperature 25 °C)

HT20

-82dBm at MCS0

-79dBm at MCS1

-77dBm at MCS2

-74dBm at MCS3

-70dBm at MCS4

-66dBm at MCS5

-65dBm at MCS6

-64dBm at MCS7

HT40

-79dBm at MCS0

-76dBm at MCS1

-74dBm at MCS2

-71dBm at MCS3

-67dBm at MCS4

-63dBm at MCS5

-62dBm at MCS6

-61dBm at MCS7

35

DSL-2640U Quick Installation Guide

Wireless Module Parameters

Modulation schemes

·

·

·

802.11b: DQPSK, DBPSK, DSSS, and CCK

802.11g: BPSK, QPSK, 16QAM, 64QAM with OFDM

802.11n: BPSK, QPSK, 16QAM, 64QAM with OFDM

Physical Parameters

Dimensions (L x W x H)

Weight ·

· 174 x 119 x 32 mm (7 x 4.7 x 1.3 in)

197 g (0.43 lb)

Operating Environment

Power

Temperature

Humidity

·

·

·

·

Output: 12V DC, 0.5A

Operating: from 0 to 40 °C

Storage: from -20 to 70 °C

From 5% to 95% (non-condensing)

36

DSL-2640U Quick Installation Guide

SAFETY RULES AND CONDITIONS

Please carefully read this section before installation and connection of the device. Make sure that the power adapter and cables are not damaged. The device should be used only as intended in accordance with the documents.

The device is intended for use in dry, clean, dust-free, and well ventilated areas with normal humidity away from strong heat sources. Do not use the device outdoors or in the areas with high humidity. Do not place foreign objects on the device. Do not obstruct the ventilation openings of the device. The environmental temperature near the device and the temperature inside the device's cover should be within the range from 0 °С to +40 °С.

Only use the power adapter supplied with the device. Do not plug in the adapter, if its case or cable are damaged. Plug the adapter only into working electrical outlets with parameters indicated on the adapter.

Do not open the cover of the device! Unplug the device before dusting and cleaning. Use a damp cloth to clean the device. Do not use liquid/aerosol cleaners or magnetic/static cleaning devices. Prevent moisture getting into the device or the power adapter.

The service life of the device is 2 years.

37

DSL-2640U Quick Installation Guide

TECHNICAL SUPPORT

You can find software updates and user documentation on our website.

D-Link provides its customers with free support within the product's warranty period.

Customers can contact the technical support group by phone or by email/Internet.

FOR TELEPHONE NUMBERS AND ADDRESSES OF D-LINK

OFFICES WORLDWIDE VISIT http://www.dlink.com/corporate/worldwideoffices/

38