D-Link DSL-G2452GR-5G Quick Installation Manual

Quick Installation Guide
DSL-G2452GR
AC1200 MU-MIMO Wireless Dual Band VDSL2 Router
with ADSL2+/3G/LTE/Gigabit Ethernet WAN Support,
2 FXS Ports and USB Port
DSL-G2452GR
Quick Installation Guide
BEFORE YOU BEGIN
Delivery Package
•
Router DSL-G2452GR
•
Power adapter DC 12V/1.5A
•
RJ-11 telephone cable
•
Ethernet cable
•
Splitter
“Quick Installation Guide” (brochure).
If any of the items are missing, please contact your reseller.
•
The “User Manual” and “Quick Installation Guide” documents are available
on D-Link website (see www.dlink.ru).
!
Using a power supply with a different voltage rating than the one
included will cause damage and void the warranty for this product.
2
DSL-G2452GR
Quick Installation Guide
Default Settings
Domain name of device
IP address of device
192.168.1.1
Username (login)
admin
Password
admin
Name of wireless network
(SSID)
2.4GHz
5GHz
Network key (PSK password)
!
dlinkrouter.local.
DSL-G2452GR
DSL-G2452GR-5G
see WPS PIN on the barcode
label on the back panel of
the device
Router DSL-G2452GR with default settings cannot connect to the
Internet. To get started, please set your own password for access to the
web-based interface and change the WLAN name (SSID); then, if
needed, configure other settings recommended by your ISP.
3
DSL-G2452GR
Quick Installation Guide
System Requirements and Equipment
•
•
An Android or iPhone mobile device (smartphone or tablet) or a computer
with any operating system that supports a web browser.
A PC web browser to access the web-based interface:
◦
Apple Safari 8 and later
◦
Google Chrome 48 and later
◦
Microsoft Internet Explorer 10 and later
◦
Microsoft Edge 20.10240 and later
◦
Mozilla Firefox 44 and later
◦
Opera 35 and later.
•
A NIC (Ethernet or Wi-Fi adapter) to connect to the router.
•
An 802.11a, b, g, n, or ac Wi-Fi adapter to create a wireless network.
•
Analog phone.
•
A USB modem (when it is necessary to connect to the Internet via mobile
operators' networks).1
Your USB modem should be equipped with an active SIM card of your
operator.
!
Some operators require subscribers to activate their USB modems prior
to using them. Please, refer to connection guidelines provided by your
operator when concluding the agreement or placed on its website.
For some models of USB modems, it is required to disable the PIN
code check on the SIM card prior to connecting the USB modem to the
router.
1 Contact your operator to get information on the service coverage and fees.
4
DSL-G2452GR
Quick Installation Guide
CONNECTING TO PC
PC with Ethernet Adapter
1. Connect an Ethernet cable between any of LAN ports located on the back
panel of the router and the Ethernet port of your PC.
2. To connect via USB modem: connect your USB modem to the USB port 2
located on the right side panel of the router.
!
In some cases you will need to reboot the router after connection of the
USB modem.
3. To connect the device to a DSL line: connect a phone cable between the
DSL port of the router and the MODEM port of the splitter. Connect your
phone to the PHONE port of the splitter. Then connect another phone
cable between a phone jack and the LINE port of the splitter.
4. To connect the device to an Ethernet line: connect an Ethernet cable
between the WAN port of the router and the Ethernet line.
5. Connect another phone cable between an FXS port of the router and the
phone.
6. Connect the power cord to the power connector port on the back panel of
the router, then plug the power adapter into an electrical outlet or power
strip.
7. Turn on the router by pressing the power button on its right side panel.
Then make sure that your PC is configured to obtain an IP address
automatically (as DHCP client).
2 It is recommended to use a USB extension cable to connect a USB modem to the
router.
5
DSL-G2452GR
Obtaining
IP
(OS Windows 7)
Quick Installation Guide
Address
Automatically
1. Click the Start button and proceed to the Control Panel window.
2. Select the Network and Sharing Center section. (If the Control Panel
has the category view (the Category value is selected from the View by
drop-down list in the top right corner of the window), choose the View
network status and tasks line under the Network and Internet
section.)
3. In the menu located on the left part of the window, select the Change
adapter settings line.
4. In the opened window, right-click the relevant Local Area Connection
icon and select the Properties line in the menu displayed.
5. In the Local Area Connection Properties window, on the
Networking tab, select the Internet Protocol Version 4 (TCP/IPv4)
line. Click the Properties button.
6
DSL-G2452GR
Quick Installation Guide
6. Make sure that the Obtain an IP address automatically and Obtain
DNS server address automatically choices of the radio buttons are
selected. Click the OK button.
7. Click the OK button in the connection properties window.
7
DSL-G2452GR
Obtaining
IP
(OS Windows 10)
Quick Installation Guide
Address
Automatically
1. Click the Start button and proceed to the Settings window.
2. Select the Network & Internet section.
3. In the Change your network settings section, select the Change
adapter options line.
4. In the opened window, right-click the relevant Local Area Connection
icon and select the Properties line in the menu displayed.
5. In the Local Area Connection Properties window, on the
Networking tab, select the Internet Protocol Version 4 (TCP/IPv4)
line. Click the Properties button.
8
DSL-G2452GR
Quick Installation Guide
6. Make sure that the Obtain an IP address automatically and Obtain
DNS server address automatically choices of the radio buttons are
selected. Click the OK button.
7. Click the Close button in the connection properties window.
9
DSL-G2452GR
Quick Installation Guide
PC with Wi-Fi Adapter
1. To connect via USB modem: connect your USB modem to the USB port 3
located on the right side panel of the router.
!
In some cases you will need to reboot the router after connection of the
USB modem.
2. To connect the device to a DSL line: connect a phone cable between the
DSL port of the router and the MODEM port of the splitter. Connect your
phone to the PHONE port of the splitter. Then connect another phone
cable between a phone jack and the LINE port of the splitter.
3. To connect the device to an Ethernet line: connect an Ethernet cable
between the WAN port of the router and the Ethernet line.
4. Connect another phone cable between an FXS port of the router and the
phone.
5. Connect the power cord to the power connector port on the back panel of
the router, then plug the power adapter into an electrical outlet or power
strip.
6. Turn on the router by pressing the power button on its right side panel.
7. Make sure that the Wi-Fi adapter of your PC is on. As a rule, modern
notebooks with built-in wireless NICs are equipped with a button or
switch that turns on/off the wireless adapter (refer to your PC documents).
If your PC is equipped with a pluggable wireless NIC, install the software
provided with your Wi-Fi adapter.
Then make sure that your Wi-Fi adapter is configured to obtain an IP address
automatically (as DHCP client).
3 It is recommended to use a USB extension cable to connect a USB modem to the
router.
10
DSL-G2452GR
Quick Installation Guide
Obtaining
IP Address
Automatically
and
Connecting to Wireless Network (OS Windows 7)
1. Click the Start button and proceed to the Control Panel window.
2. Select the Network and Sharing Center section. (If the Control Panel
has the category view (the Category value is selected from the View by
drop-down list in the top right corner of the window), choose the View
network status and tasks line under the Network and Internet
section.)
3. In the menu located on the left part of the window, select the Change
adapter settings line.
4. In the opened window, right-click the relevant Wireless Network
Connection icon. Make sure that your Wi-Fi adapter is on, then select
the Properties line in the menu displayed.
5. In the Wireless Network Connection Properties window, on the
Networking tab, select the Internet Protocol Version 4 (TCP/IPv4)
line. Click the Properties button.
11
DSL-G2452GR
Quick Installation Guide
6. Make sure that the Obtain an IP address automatically and Obtain
DNS server address automatically choices of the radio buttons are
selected. Click the OK button.
7. Click the OK button in the connection properties window.
8. To open the list of available wireless networks, select the icon of the
wireless network connection and click the Connect To button or leftclick the network icon in the notification area located on the right side of
the taskbar.
12
DSL-G2452GR
Quick Installation Guide
9. In the opened window, in the list of available wireless networks, select the
wireless network DSL-G2452GR (for operating in the 2.4GHz band) or
DSL-G2452GR-5G (for operating in the 5GHz band) and click the
Connect button.
10. In the opened window, enter the network key (see WPS PIN on the
barcode label on the back panel of the device) in the Security key field
and click the OK button.
11. Wait for about 20-30 seconds. After the connection is established, the
network icon will be displayed as the signal level scale.
!
If you perform initial configuration of the router via Wi-Fi connection,
note that immediately after changing the wireless default settings of the
router you will need to reconfigure the wireless connection using the
newly specified settings.
13
DSL-G2452GR
Quick Installation Guide
Obtaining
IP Address
Automatically
and
Connecting to Wireless Network (OS Windows 10)
1. Click the Start button and proceed to the Settings window.
2. Select the Network & Internet section.
3. In the Change your network settings section, select the Change
adapter options line.
4. In the opened window, right-click the relevant Wireless Network
Connection icon. Make sure that your Wi-Fi adapter is on, then select
the Properties line in the menu displayed.
5. In the Wireless Network Connection Properties window, on the
Networking tab, select the Internet Protocol Version 4 (TCP/IPv4)
line. Click the Properties button.
6. Make sure that the Obtain an IP address automatically and Obtain
DNS server address automatically choices of the radio buttons are
selected. Click the OK button.
7. Click the Close button in the connection properties window.
14
DSL-G2452GR
Quick Installation Guide
8. To open the list of available wireless networks, select the icon of the
wireless network connection and click the Connect To button or leftclick the network icon in the notification area located on the right side of
the taskbar.
9. In the opened window, in the list of available wireless networks, select the
wireless network DSL-G2452GR (for operating in the 2.4GHz band) or
DSL-G2452GR-5G (for operating in the 5GHz band) and click the
Connect button.
10. In the opened window, enter the network key (see WPS PIN on the
barcode label on the back panel of the device) in the Security key field
and click the Next button.
11. Allow or forbid your PC to be discoverable by other devices on this
network (Yes / No).
15
DSL-G2452GR
Quick Installation Guide
12. Wait for about 20-30 seconds. After the connection is established, the
network icon will be displayed as a dot with curved lines indicating the
signal level.
!
If you perform initial configuration of the router via Wi-Fi connection,
note that immediately after changing the wireless default settings of the
router you will need to reconfigure the wireless connection using the
newly specified settings.
16
DSL-G2452GR
Quick Installation Guide
CONFIGURING ROUTER
Connecting to Web-based Interface
Start a web browser. In the address bar of the web browser, enter the domain
name of the router (by default, dlinkrouter.local) with a dot at the end
and press the Enter key. Also you can enter the IP address of the device (by
default, 192.168.1.1).
!
If the error “The page cannot be displayed” (or “Unable to display the
page”/“Could not connect to remote server ”) occurs upon connecting to
the web-based interface of the router, make sure that you have properly
connected the router to your computer.
If the device has not been configured previously or the default settings have
been restored, after access to the web-based interface the Initial Configuration
Wizard opens (see the Initial Configuration Wizard section, page 21).
17
DSL-G2452GR
Quick Installation Guide
If you configured the device previously, after access to the web-based interface
the login page opens. Enter the username (admin) in the Username field
and the password you specified in the Password field, then click the LOGIN
button.
In order not to log out, move the Stay signed in switch to the right. After
closing the web browser or rebooting the device, you need to enter the
username and the password again.
If you enter a wrong password several times, the web-based interface will be
blocked for a while. Please wait for one minute and reenter the password you
specified.
18
DSL-G2452GR
Quick Installation Guide
The Summary page displays general information on the router and its
software.
19
DSL-G2452GR
Quick Installation Guide
The Home page displays links to the most frequently used pages with device's
settings.
The web-based interface of the router is multilingual. You can select the
needed language upon the initial configuration of the web-based interface of
the router or in the System / Configuration section of the menu.
Other settings of the router are available in the menu in the left part of the
page. Go to the relevant section and select the needed page or run the wizard
in the Initial Configuration section.
20
DSL-G2452GR
Quick Installation Guide
Initial Configuration Wizard
In order to start the Initial Configuration Wizard manually, go to the Initial
Configuration section.
Click the OK button and wait until the factory default settings are restored.
If you perform initial configuration of the router via Wi-Fi connection, please
make sure that you are connected to the wireless network of DSL-G2452GR
(see the WLAN name (SSID) in the Default Settings section, page 3) and click
the NEXT button. Then click the START button.
If the device has not been configured previously or the default settings have
been restored, the Initial Configuration Wizard starts automatically upon
access to the web-based interface or upon opening a web site on the Internet.
21
DSL-G2452GR
Quick Installation Guide
1. Click YES in order to leave the current language of the web-based
interface or click NO to select another language.
2. On the next page, click the CONTINUE button.
22
DSL-G2452GR
Quick Installation Guide
Selecting Operation Mode
Select the needed operation mode and click the NEXT button.
Router
In order to connect your device to a VDSL or ADSL line, on the Device
mode page, from the Connection method list, select the VDSL or ADSL
value correspondingly. In this mode you can configure a WAN connection, set
your own settings for the wireless network in the 2.4GHz and 5GHz bands,
configure LAN ports to connect an STB or VoIP phone, and set your own
password for access to the web-based interface of the device.
In order to connect your device to a private Ethernet line, on the Device
mode page, from the Connection method list, select the Ethernet (WAN)
value. Then from the Work mode list, select the Router value. In this mode
you can configure a WAN connection, set your own settings for the wireless
network in the 2.4GHz and 5GHz bands, configure LAN ports to connect an
STB or VoIP phone, and set your own password for access to the web-based
interface of the device. If you want to use one of the LAN ports to connect
your device to a private Ethernet line, select the Ethernet (LAN) value.
23
DSL-G2452GR
Quick Installation Guide
In order to connect your device to the network of a 3G or LTE operator, on the
Device mode page, from the Connection method list, select the Mobile
Internet value. In this mode you can configure a 3G/LTE WAN connection,
set your own settings for the wireless network in the 2.4GHz and 5GHz bands,
and set your own password for access to the web-based interface of the device.
In order to connect your device to a wireless ISP (WISP), on the Device
mode page, from the Connection method list, select the Wi-Fi value.
Then from the Work mode list select the WISP Repeater value. In this
mode you can connect your device to another access point, configure a WAN
connection, set your own settings for the wireless network in the 2.4GHz and
5GHz bands, and set your own password for access to the web-based interface
of the device.
24
DSL-G2452GR
Quick Installation Guide
Access Point or Repeater
In order to connect your device to a wired router for adding a wireless network
to the existing local network, on the Device mode page, from the
Connection method list, select the Ethernet (WAN) value. Then from the
Work mode list select the Access point value. In this mode you can
change the LAN IP address, set your own settings for the wireless network in
the 2.4GHz and 5GHz bands, and set your own password for access to the
web-based interface of the device.
In order to connect your device to a wireless router for extending the range of
the existing wireless network, on the Device mode page, from the
Connection method list, select the Wi-Fi value. Then from the Work
mode list select the Repeater value. In this mode you can change the LAN
IP address, connect your device to another access point, set your own settings
for the wireless network in the 2.4GHz and 5GHz bands, and set your own
password for access to the web-based interface of the device.
In order to let wired PCs connected to your device access the network of a
wireless router, on the Device mode page, from the Connection method
list, select the Wi-Fi value. Then from the Work mode list select the Client
value. In this mode you can change the LAN IP address, connect your device
to another access point, and set your own password for access to the webbased interface of the device.
25
DSL-G2452GR
Quick Installation Guide
Configuring LAN Port as WAN Port
This configuration step is available for the Ethernet (LAN) connection
method.
1. On the Device connection page, select a free LAN port which will be
used as the WAN port.
2.
Click the NEXT button.
26
DSL-G2452GR
Quick Installation Guide
Creating 3G/LTE WAN Connection
This configuration step is available for the Mobile Internet mode.
1. If the PIN code check is enabled for the SIM card inserted into your USB
modem, enter the PIN code in the PIN field and click the APPLY button.
2. Please wait while the router automatically creates a WAN connection for
your mobile operator.
3. Click the NEXT button.
27
DSL-G2452GR
Quick Installation Guide
If the router failed to create a WAN connection automatically, click the
CONFIGURE MANUALLY button. On the Modem settings page,
configure all needed settings and click the NEXT button.
28
DSL-G2452GR
Quick Installation Guide
Changing LAN IPv4 Address
This configuration step is available for the Access point, Repeater, and
Client modes.
1. Select the Automatic obtainment of IPv4 address to let DSLG2452GR automatically obtain the LAN IPv4 address.
2. In the Hostname field, you should specify a domain name of the router
using which you can access the web-based interface after finishing the
Wizard. Enter a new domain name of the router ending with .local or
leave the value suggested by the router.
!
In order to access the web-based interface using the domain name, in
the address bar of the web browser, enter the name of the router with a
dot at the end.
29
DSL-G2452GR
Quick Installation Guide
If you want to manually assign the LAN IPv4 address for DSL-G2452GR, do
not select the Automatic obtainment of IPv4 address checkbox and fill
in the IP address, Subnet mask, DNS IP address, Hostname fields
and, if needed, the Gateway IP address field. Make sure that the assigned
address does not coincide with the LAN IPv4 address of the router to which
your device connects.
3. Click the NEXT button.
30
DSL-G2452GR
Quick Installation Guide
Wi-Fi Client
This configuration step is available for the WISP Repeater, Repeater, and
Client modes.
1. On the Wi-Fi Сlient page, click the WIRELESS NETWORKS button
and select the network to which you want to connect in the opened
window. When you select a network, the Network name (SSID) and
BSSID fields are filled in automatically.
If you cannot find the needed network in the list, click the UPDATE LIST
icon (
).
2. If a password is needed to connect to the selected network, fill in the
relevant field. Click the Show icon (
) to display the entered
password.
If you connect to a hidden network, select the band where the hidden network
operates from the Frequency band list and enter the network name in the
Network name (SSID) field. Then select a needed value from the Network
authentication list and then, if needed, enter the password in the relevant
field.
3. Click the NEXT button.
31
DSL-G2452GR
Quick Installation Guide
Configuring Ethernet WAN Connection
This configuration step is available for the Ethernet (WAN), Ethernet
(LAN) connection methods, and the WISP Repeater mode.
!
You should configure your WAN connection in accordance with data
provided by your Internet service provider (ISP). Make sure that you
have obtained all necessary information prior to configuring your
connection. Otherwise contact your ISP.
1. On the Internet connection type page, click the SCAN button
(available for the Ethernet (WAN) connection method only) to
automatically specify the connection type used by your ISP or manually
select the needed value from the Connection type list.
Static IPv4: Fill in the following fields: IP address, Subnet mask,
Gateway IP address, and DNS IP address.
Static IPv6: Fill in the following fields: IP address, Prefix, Gateway IP
address, and DNS IP address.
32
DSL-G2452GR
Quick Installation Guide
PPPoE, IPv6 PPPoE, PPPoE Dual Stack, PPPoE + Dynamic IP (PPPoE
Dual Access): Enter authorization data provided by your ISP (the username
(login) in the Username field and the password in the Password field).
Click the Show icon ( ) to display the entered password. If authorization is
not required, select the Without authorization checkbox.
PPPoE + Static IP (PPPoE Dual Access): Enter authorization data provided
by your ISP (the username (login) in the Username field and the password in
the Password field). Click the Show icon ( ) to display the entered
password. If authorization is not required, select the Without authorization
checkbox. Also fill in the following fields: IP address, Subnet mask,
Gateway IP address, and DNS IP address.
33
DSL-G2452GR
Quick Installation Guide
PPTP + Dynamic IP or L2TP + Dynamic IP: Enter authorization data
provided by your ISP (the username (login) in the Username field and the
password in the Password field). Click the Show icon ( ) to display the
entered password. If authorization is not required, select the Without
authorization checkbox. In the VPN server address field, enter the IP or
URL address of the PPTP or L2TP authentication server.
PPTP + Static IP or L2TP + Static IP: Enter authorization data provided by
your ISP (the username (login) in the Username field and the password in
the Password field). Click the Show icon ( ) to display the entered
password. If authorization is not required, select the Without authorization
checkbox. In the VPN server address field, enter the IP or URL address of
the PPTP or L2TP authentication server. Also fill in the following fields: IP
address, Subnet mask, Gateway IP address, and DNS IP address.
34
DSL-G2452GR
Quick Installation Guide
2. If your ISP uses MAC address binding, select the Clone MAC address
of your device checkbox (available for the Router mode only).
3. If the Internet access is provided via a VLAN channel, select the Use
VLAN checkbox and fill in the VLAN ID field (available for the Router
mode only).
4. Click the NEXT button.
35
DSL-G2452GR
Quick Installation Guide
Configuring VDSL WAN Connection
This configuration step is available for the VDSL connection method.
!
You should configure your WAN connection in accordance with data
provided by your Internet service provider (ISP). Make sure that you have
obtained all necessary information prior to configuring your connection.
Otherwise contact your ISP.
1. On the Internet connection type page, from the Connection type
list, select the connection type used by your ISP and fill in the fields
displayed on the page.
Static IPv4: Fill in the following fields: IP address, Subnet mask,
Gateway IP address, and DNS IP address.
Static IPv6: Fill in the following fields: IP address, Prefix, Gateway IP
address, and DNS IP address.
36
DSL-G2452GR
Quick Installation Guide
PPPoE, IPv6 PPPoE, PPPoE Dual Stack: Enter authorization data provided
by your ISP (the username (login) in the Username field and the password in
the Password field). Click the Show icon ( ) to display the entered
password. If authorization is not required, select the Without authorization
checkbox.
2. If your ISP uses MAC address binding, select the Clone MAC address
of your device checkbox.
3. If the Internet access is provided via a VLAN channel, select the Use
VLAN checkbox and fill in the VLAN ID field.
4. Click the NEXT button.
37
DSL-G2452GR
Quick Installation Guide
Configuring ADSL WAN Connection
This configuration step is available for the ADSL connection method.
!
You should configure your WAN connection in accordance with data
provided by your Internet service provider (ISP). Make sure that you have
obtained all necessary information prior to configuring your connection.
Otherwise contact your ISP.
1. On the Internet connection type page, from the Connection type
list, select the connection type used by your ISP and fill in the fields
displayed on the page.
Static IPv4, IPoA: Fill in the following fields: IP address, Subnet mask,
Gateway IP address, and DNS IP address.
Static IPv6: Fill in the following fields: IP address, Prefix, Gateway IP
address, and DNS IP address.
38
DSL-G2452GR
Quick Installation Guide
PPPoE, IPv6 PPPoE, PPPoE Dual Stack, PPPoA: Enter authorization data
provided by your ISP (the username (login) in the Username field and the
password in the Password field). Click the Show icon ( ) to display the
entered password. If authorization is not required, select the Without
authorization checkbox.
2. Specify the VPI and VCI values in the relevant fields.
3. Click the NEXT button.
39
DSL-G2452GR
Quick Installation Guide
Configuring Wireless Network
This configuration step is not available for the Client mode.
1. On the Wireless Network 2.4 GHz page, in the Network name field,
specify your own name for the wireless network in the 2.4GHz band or
leave the value suggested by the router.
2. In the Password field, specify your own password for access to the
wireless network or leave the value suggested by the router (WPS PIN of
the device, see the barcode label).
3. If the router is used as a Wi-Fi client, you can specify the same
parameters of the wireless network as specified for the network to which
you are connecting. To do this, click the USE button (available for the
WISP Repeater and Repeater modes only).
4. You can restore the parameters of the wireless network specified before
resetting to factory defaults. To do this, click the RESTORE button.
40
DSL-G2452GR
Quick Installation Guide
5. If you want to create an additional wireless network isolated from your
LAN in the 2.4GHz band, select the Enable guest network checkbox
(available for the Mobile Internet, Router, and WISP Repeater
modes only).
6. In the Network name field, specify your own name for the guest
wireless network or leave the value suggested by the router.
7. If you want to create a password for access to the guest wireless network,
deselect the Open network checkbox and fill in the Password field.
8. If you want to limit the bandwidth of the guest wireless network, select
the Enable shaping checkbox and fill in the Shaping field.
9. Click the NEXT button.
10. On the Wireless Network 5 GHz page, specify needed settings for the
wireless network in the 5GHz band and click the NEXT button.
41
DSL-G2452GR
Quick Installation Guide
Configuring LAN Ports for IPTV/VoIP
This configuration step is available for the Router mode.
1. On the IPTV page, select the Is an STB connected to the device
checkbox.
2. Select a free LAN port for connecting your set-top box.
3. If the IPTV service is provided via a VLAN channel, select the Use
VLAN ID checkbox and fill in the VLAN ID field (not available for the
ADSL connection method).
4. For the ADSL connection method: Specify the VPI and VCI values in the
relevant fields.
5. Click the NEXT button.
42
DSL-G2452GR
Quick Installation Guide
6. On the VoIP page, select the Is an IP phone connected to the
device checkbox.
7. Select a free LAN port for connecting your IP phone.
8. If the VoIP service is provided via a VLAN channel, select the Use
VLAN ID checkbox and fill in the VLAN ID field (not available for the
ADSL connection method).
9. For the ADSL connection method: Specify the VPI and VCI values in the
relevant fields.
10. Click the NEXT button.
43
DSL-G2452GR
Quick Installation Guide
Changing Web-based Interface Password
On this page you should change the default administrator password. To do this,
enter a new password in the User’s interface password and Password
confirmation fields. You may set any password except admin. Use digits,
Latin letters (uppercase and/or lowercase), and other characters available in the
US keyboard layout.4
!
Remember or write down the new password for the administrator
account. In case of losing the new password, you can access the settings
of the router only after restoring the factory default settings via the
hardware RESET button. This procedure wipes out all settings that you
have configured for your router.
Click the NEXT button.
On the next page, check all the settings you have just specified.
Also you can save a text file with parameters set by the Wizard to your PC. To
do this, click the SAVE CONFIGURATION FILE button and follow the
dialog box appeared.
To finish the Wizard, click the APPLY button. The router will apply settings,
reboot, if needed, and check the Internet connection if the Wizard has
configured a WAN connection.
4 0-9, A-Z, a-z, space, !"#$%&'()*+,-./:;<=>?@[\]^_`{|}~.
44
DSL-G2452GR
Quick Installation Guide
Configuring Local Area Network
1. Go to the Connections Setup / LAN page.
2. If needed, change the IPv4 address of the router's LAN interface and the
mask of the local subnet. To do this, click the IPv4 tab and specify
needed values in the IP address and Mask fields in the Local IP
Address section.
3. If needed, add a static IPv6 address of the router's LAN interface. To do
this, click the IPv6 tab. In the Local IPv6 Address section, click the
ADD button (
). In the opened window, specify needed values in the
IPv6 address and Prefix fields and click the APPLY button.
45
DSL-G2452GR
Quick Installation Guide
4. IPv4 address assignment. By default, the built-in DHCP server of
the router assigns IPv4 addresses to the devices of the LAN. If you want
to manually assign IPv4 addresses, disable the DHCP server (click the
IPv4 tab and select the Disable value from the Mode of dynamic IP
address assignment drop-down list in the Dynamic IP Addresses
section).
46
DSL-G2452GR
Quick Installation Guide
5. IPv6 address assignment. By default, the devices of the LAN
automatically assign IPv6 addresses to themselves (the Stateless value
is selected from the Mode of dynamic IPv6 address assignment
drop-down list in the Dynamic IPv6 Addresses section on the IPv6
tab). If the devices of the LAN do not support IPv6 address
autoconfiguration, use the built-in DHCPv6 server of the router (select
the Stateful value from the Mode of dynamic IPv6 address
assignment drop-down list). If you want to manually assign IPv6
addresses to devices of the LAN, select the Disable value from the
Mode of dynamic IPv6 address assignment drop-down list.
6. After specifying the needed parameters on the Connections Setup /
LAN page, click the APPLY button.
47
DSL-G2452GR
Quick Installation Guide
Configuring VoIP via SIP
1. Connect the phone to the PHONE1 or PHONE2 port of the router using
an RJ-11 cable.
2. Go to the VoIP / Home page.
3. In the Profile list section, select the Voice profile line.
4. In the opened window, move the Enable switch to the right.
5. If your provider does not require automatic obtainment of the SIP proxy
server address, move the Enable DHCP option 120 switch to the left.
6. Click the SAVE button and then click the APPLY button.
7. Go to your profile basic settings page (VoIP / Voice profile / Basic
Settings for the default profile).
8. In the SIP Proxy section, fill in the Address field.
48
DSL-G2452GR
Quick Installation Guide
9. If your provider uses a SIP domain, in the SIP Domain section, fill in
the SIP domain name field and, if needed, move the Use domain to
register switch to the right (contact your ISP to clarify if the setting is
required).
10. Click the APPLY button.
11. In the List of SIP Lines section, click the ADD button (
).
12. On the opened page, in the General section, move the Enable switch to
the right.
49
DSL-G2452GR
Quick Installation Guide
13. From the Port drop-down list, select the phone 1 or phone 2 value
(the values correspond to the PHONE1 and PHONE2 ports).
14. Fill in the SIP ID / Number field.
15. Enter the username in the Username field (as a rule, the username and
the phone number are the same) and fill in the Password field (contact
your ISP to clarify if the setting is required).
!
Simultaneous operation of no more than two lines is possible.
16. If needed, fill in other fields on the VoIP / Voice profile / Basic
Settings page in accordance with data provided by the ISP.
17. Click the APPLY button.
After completing configuration, you can check the registration status of the
line on the Summary page.
50
DSL-G2452GR
Quick Installation Guide
Configuring Network Printer
1. Make sure that a driver for your printer which will be used as a network
printer is installed on your PC.5
2. To connect the printer to the router, power off both devices. Connect the
printer to the USB port of the router, power on the printer, then power on
the router.
3. Then access the web-based interface and go to the Print Server page.
4. Move the Enable print server switch to the right, from the Printer
drop-down list, select the printer connected to the USB port of the router,
and click the APPLY button.
5. Click the Start button and go to the Control Panel window.
6. Select the Hardware and Sound section. (If the Control Panel has the
category view (the Category value is selected from the View by dropdown list in the top right corner of the window), choose the View
devices and printers line.)
5 Some home printers can work incorrectly as network printers. Contact the technical
support of your printer’s manufacturer to clarify if your printer supports this function.
51
DSL-G2452GR
Quick Installation Guide
7. In the opened window, click the Add a printer button.
8. Select the Add a local printer value and click the Next button.
9. Select the Create a new port choice of the radio button and then select
the Standard TCP/IP Port value from the Type of port drop-down
list. Click the Next button.
52
DSL-G2452GR
Quick Installation Guide
10. Enter the IP address of the router in the Hostname or IP address field
(by default, 192.168.1.1). Deselect the Query the printer and
automatically select the driver to use checkbox and, if needed,
change the name of the port in the Port name field. Click the Next
button.
11. Wait for about 20-30 seconds. In the opened Additional port
information required window, select the Custom choice of the radio
button, click the Settings button, and make sure that the RAW choice of
the radio button is selected in the Protocol section and the 9100 value is
specified in the Raw Settings section. Click the OK button.
12. Then in the Additional port information required window, select the
Standard choice of the radio button and click the Next button.
53
DSL-G2452GR
Quick Installation Guide
13. Select your printer and click the Next button.
14. Select the Use the driver that is currently installed choice of the
radio button and click the Next button.
15. Enter a name of the printer (you can specify any name) in the Printer
name field and click the Next button.
54
DSL-G2452GR
Quick Installation Guide
16. In the Printer Sharing window, select the Do not share this printer
choice of the radio button and click the Next button.
17. If you need to print a test page, click the Print a test page button. To
finish the printer installation, click the Finish button.
55
DSL-G2452GR
Quick Installation Guide
SPECIFICATIONS*
Hardware
Processor
·
RTL8685PB (1GHz)
RAM
·
128MB, DDR2, built in processor
Flash
·
16MB, SPI
Interfaces
·
·
·
·
·
10/100/1000BASE-T WAN port
4 10/100/1000BASE-T LAN ports
1 RJ-11 DSL port
2 RJ-11 FXS ports
USB 2.0 port
LEDs
·
·
·
·
·
·
·
·
·
·
POWER
DSL
INTERNET
WAN
LAN 1-4
2.4GHz
5GHz
WPS
USB
FXS 1-2
Buttons
·
·
·
·
Power button
RESET button to restore factory default settings
WPS button to set up wireless connection
WLAN button to enable/disable wireless network
Antenna
·
·
Two internal antennas for 2.4GHz band (2dBi gain)
Two internal antennas for 5GHz band (2dBi gain)
MIMO
·
2 x 2, MU-MIMO
Power connector
·
Power input connector (DC)
* The device features are subject to change without notice. For the latest versions of the
firmware and relevant documentation, visit www.dlink.ru.
56
DSL-G2452GR
Quick Installation Guide
DSL Parameters
VDSL/ADSL Standards
·
·
·
·
VDSL2: ITU G.993.2, support of 8a, 8b, 8c, 8d, 12a,
12b, 17a, 30a, 35b
ADSL: Multi-mode, ANSI T1.413 Issue 2, ITU-T G.992.1
(G.dmt) Annex A, ITU-T G.992.2 (G.lite) Annex A, ITU-T
G.994.1 (G.hs)
ADSL2: ITU-T G.992.3 (G.dmt.bis) Annex A/L/M, ITU-T
G.992.4 (G.lite.bis) Annex A
ADSL2+: ITU-T G.992.5 Annex A/L/M
ITU-T G.993.5 (G.vector)
ITU-T G.998.4 (G.inp)
·
·
·
·
·
·
·
·
·
Bridged and routed Ethernet encapsulation
VC-based or LLC-based multiplexing
ATM Forum UNI3.1/4.0 PVC (up to 8 PVCs)
ATM Adaptation Layer Type 5 (AAL5)
ITU-T I.610 OAM F4/F5 loopback
ATM QoS
PPP over ATM (RFC 2364)
PPP over Ethernet (PPPoE)
Keep-alive for PPP connections
·
·
·
·
·
·
·
·
·
Mobile Internet (via supported USB modem)
PPPoE / IPv6 PPPoE / PPPoE Dual Stack / PPPоA
Static IPv4 / Dynamic IPv4 / IPoA
Static IPv6 / Dynamic IPv6
PPPoE + Static IP (PPPoE Dual Access)
PPPoE + Dynamic IP (PPPoE Dual Access)
PPTP/L2TP + Static IP
PPTP/L2TP + Dynamic IP
Bridge
·
·
ATM/PPP Protocols
Software
WAN connection types
57
DSL-G2452GR
Quick Installation Guide
Software
·
·
·
·
DHCP server/relay
Advanced configuration of built-in DHCP server
Stateful/Stateless mode for IPv6 address assignment,
IPv6 prefix delegation
DNS relay
Dynamic DNS
Static IPv4/IPv6 routing
IGMP Proxy
IGMP snooping
RIP
Support of UPnP IGD
Support of VLAN
WAN ping respond
Support of SIP ALG
Support of RTSP
WAN failover
LAN/WAN conversion
Autonegotiation of speed, duplex mode, and flow
control / Manual speed and duplex mode setup for each
Ethernet port
Built-in UDPXY application
Equal load distribution while using several WAN
connections (traffic balancing)
Port mirroring
Firewall functions
·
·
·
·
·
·
·
·
·
Network Address Translation (NAT)
Stateful Packet Inspection (SPI)
IPv4/IPv6 filter
MAC filter
URL filter
DMZ
Virtual servers
Built-in Yandex.DNS web content filtering service
Built-in SkyDNS web content filtering service
VPN
·
·
·
·
·
·
IPsec/PPTP/L2TP/PPPoE pass-through
PPTP/L2TP servers
PPTP/L2TP tunnels
L2TP over IPsec
GRE/EoGRE tunnels
IPsec tunnels
Transport/Tunnel mode
IKEv1/IKEv2 support
DES encryption
NAT Traversal
Support of DPD (Keep-alive for VPN tunnels)
Network functions
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
58
DSL-G2452GR
Quick Installation Guide
Software
QoS
·
·
Interface grouping
VLAN priority (802.1p)
USB interface functions
·
USB modem
Auto connection to available type of supported network
(4G/3G/2G)
Auto configuration of connection upon plugging in USB
modem
Enabling/disabling PIN code check, changing PIN code6
Sending/receiving/reading/removing SMS messages6
Support of USSD requests6
USB storage
File browser
Print server
Access to storage via accounts
Built-in Samba/FTP/DLNA server
Built-in
Transmission
torrent
client;
uploading/downloading files from/to USB storage
·
Management and monitoring
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
6
Local and remote access to settings through
SSH/TELNET/WEB (HTTP/HTTPS)
Multilingual web-based interface for configuration and
management
Support of D-Link Assistant application for Android and
iPhone smartphones
Notification on connection problems and auto redirect to
settings
Firmware update via web-based interface
Automatic notification on new firmware version
Saving/restoring configuration to/from file
Support of logging to remote host/connected USB
storage
Automatic synchronization of system time with NTP
server and manual time/date setup
Ping utility
Traceroute utility
TR-069 client
SNMP agent
Schedules for rules and settings of firewall, automatic
reboot, and enabling/disabling wireless network and WiFi filter
Automatic upload of configuration file from ISP's server
(Auto Provision)
For some models of USB modems.
59
DSL-G2452GR
Quick Installation Guide
Wireless Module Parameters
·
·
·
·
IEEE 802.11ac Wave 2
IEEE 802.11a/b/g/n
IEEE 802.11k/v
IEEE 802.11w
·
·
·
2400 ~ 2483.5MHz
5150 ~ 5350MHz
5650 ~ 5850MHz
Wireless connection security
·
·
·
·
·
WEP
WPA/WPA2 (Personal/Enterprise)
WPA3 (Personal)
МАС filter
WPS (PBC/PIN)
Advanced functions
·
·
·
·
·
·
·
Support of client mode
WMM (Wi-Fi QoS)
Information on connected Wi-Fi clients
Advanced settings
Smart adjustment of Wi-Fi clients
Guest Wi-Fi / support of MBSSID
Rate limitation for wireless network/separate MAC
addresses
Periodic scan of channels, automatic switch to least
loaded channel
Support of 2.4GHz/5GHz TX Beamforming
Autonegotiation of channel bandwidth in accordance
with environment conditions (20/40 Coexistence)
Support of STBC
Standards
Frequency range
The frequency range depends
upon the radio frequency
regulations applied in your
country
·
·
·
·
Wireless connection rate
·
·
·
·
·
IEEE 802.11a: 6, 9, 12, 18, 24, 36, 48, and 54Mbps
IEEE 802.11b: 1, 2, 5.5, and 11Mbps
IEEE 802.11g: 6, 9, 12, 18, 24, 36, 48, and 54Mbps
IEEE 802.11n (2.4GHz/5GHz): from 6.5 to 300Mbps
(from MCS0 to MCS15)
IEEE 802.11ac (5GHz): from 6.5 to 867Mbps (from
MCS0 to MCS9)
60
DSL-G2452GR
Quick Installation Guide
Wireless Module Parameters
Transmitter output power
·
802.11a
16dBm at 6, 54Mbps
The maximum value of the
transmitter
output
power
depends
upon
the
radio
frequency regulations applied in
your country
·
802.11b
18dBm at 1, 11Mbps
·
802.11g
17dBm at 6, 54Mbps
·
802.11n
HT20/HT40
16dBm at MCS0, 7
·
802.11ac
VHT20
16dBm at MCS0, 8
VHT40
16dBm at MCS0, 9
VHT80
15dBm at MCS0, 9
·
802.11a
-86dBm at 6Mbps
-65dBm at 54Mbps
·
802.11b
-90dBm at 1Mbps
-76dBm at 11Mbps
·
802.11g
-86dBm at 6Mbps
-68dBm at 54Mbps
·
802.11n
2.4GHz
HT20
-85dBm at MCS0
-67dBm at MCS7
HT40
-82dBm at MCS0
-64dBm at MCS7
5GHz
HT20
-85dBm at MCS0
-65dBm at MCS7
HT40
-82dBm at MCS0
-61dBm at MCS7
Receiver sensitivity
61
DSL-G2452GR
Quick Installation Guide
Wireless Module Parameters
Modulation schemes
·
802.11ac
VHT20
-82dBm at MCS0
-59dBm at MCS8
VHT40
-79dBm at MCS0
-54dBm at MCS9
VHT80
-76dBm at MCS0
-51dBm at MCS9
·
·
·
·
·
802.11a: BPSK, QPSK, 16 QAM, 64 QAM with OFDM
802.11b: DQPSK, DBPSK, DSSS, and CCK
802.11g: BPSK, QPSK, 16 QAM, 64 QAM with OFDM
802.11n: BPSK, QPSK, 16 QAM, 64 QAM with OFDM
802.11ac: BPSK, QPSK, 16 QAM, 64 QAM, 256 QAM
with OFDM
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
Support of several SIP profiles
Individual account per port
Invite with Challenge
Register by IP address or domain name of SIP server
Backup proxy support
Support of DHCP option 120
RFC3986 SIP URI format support
Outbound proxy support
STUN client
NAT public IP address
NAT keep-alive
Session timer (re-invite/update)
Call types: voice/modem/fax
User programmable Dial Plan
Manual peer table (for P2P calls)
Handling numbers in E.164 format
Phone
General SIP Features
62
DSL-G2452GR
Quick Installation Guide
Phone
Call Features
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
Voice Features
·
·
·
·
·
·
·
·
·
·
·
·
·
·
Direct IP-to-IP сall without SIP proxy (P2P)
Call hold/retrieve
Call awaiting
Forwarding (unconditional, busy, no answer)
Do Not Disturb
Anonymous call blocking
Speed/abbreviated dialing
PIN code before dialing
Hotline
Vertical service codes
CLIR
Intercom (internal calls without SIP server)
Filtering SIP packets by IP address/domain name
(white/black list)
Logging and recording calls
Sending text messages to VoIP gateways/IP phones
Codecs: G.711 a/μ-law, G.729A, G.726, G.722, G.723.1,
GSMFR, ILBC
DTMF detection and generation
In-band DTMF, out-of-band DTMF (RFC2833, SIPINFO)
Comfort Noise Generation (CNG)
Voice Activity Detection (VAD)
Dynamic Jitter Buffer
Echo Cancellation (LEC/NLP)
Call progress tone generation (FXS)
DTMF/PULSE dial support
Caller ID detection and generation
T.30 FAX bypass to G.711, T.38 Real Time FAX Relay,
V.152
Adjustable Flash Time
Advanced call transfer
Volume control (speaker/microphone)
63
DSL-G2452GR
Quick Installation Guide
Physical Parameters
Dimensions (L x W x H)
·
198 x 59 x 168 mm (7.8 x 2.3 x 6.6 in)
Weight
·
340 g (0.75 lb)
Power
·
Output: 12V DC, 1.5A
Temperature
·
·
Operating: from 5 to 40 °C
Storage: from -20 to 70 °C
Humidity
·
·
Operating: from 10% to 90% (non-condensing)
Storage: from 5% to 95% (non-condensing)
Operating Environment
64
DSL-G2452GR
Quick Installation Guide
Supported USB modems7
GSM
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
Alcatel X500
D-Link DWM-152C1
D-Link DWM-156A6
D-Link DWM-156A7
D-Link DWM 156A8
D-Link DWM-156C1
D-Link DWM-157B1
D-Link DWM-157B1 (Velcom)
D-Link DWM-158D1
D-Link DWR-710
Huawei E150
Huawei E1550
Huawei E156G
Huawei E160G
Huawei E169G
Huawei E171
Huawei E173 (Megafon)
Huawei E220
Huawei E3131 (MTS 420S)
Huawei E352 (Megafon)
Huawei E3531
Prolink PHS600
Prolink PHS901
ZTE MF112
ZTE MF192
ZTE MF626
ZTE MF627
ZTE MF652
ZTE MF667
ZTE MF668
ZTE MF752
7 The manufacturer does not guarantee proper operation of the router with every
modification of the firmware of USB modems.
65
DSL-G2452GR
Quick Installation Guide
Supported USB modems
LTE
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
Alcatel IK40V
D-Link DWM-222
Huawei E3131
Huawei E3272
Huawei E3351
Huawei E3372s
Huawei E3372h-153
Huawei E3372h-320
Huawei E367
Huawei E392
Megafon M100-1
Megafon M100-2
Megafon M100-3
Megafon M100-4
Megafon M150-1
Megafon M150-2
Megafon M150-3
Quanta 1K6E (Beeline 1K6E)
MTS 824F
MTS 827F
Yota LU-150
Yota WLTUBA-107
ZTE MF823
ZTE MF823D
ZTE MF827
ZTE MF833T
ZTE MF833V
Smartphones in USB
tethering mode
·
Some models of Android smartphones
66
DSL-G2452GR
Quick Installation Guide
SAFETY RULES AND CONDITIONS
Please carefully read this section before installation and connection of the
device. Make sure that the power adapter and cables are not damaged. The
device should be used only as intended in accordance with the documents.
The device is intended for use in dry, clean, dust-free, and well ventilated areas
with normal humidity away from strong heat sources. Do not use the device
outdoors or in the areas with high humidity. Do not place foreign objects on
the device. Do not obstruct the ventilation openings of the device. The
environmental temperature near the device and the temperature inside the
device's cover should be within the range from 0 °С to +40 °С.
Only use the power adapter supplied with the device. Do not plug in the
adapter, if its case or cable are damaged. Plug the adapter only into working
electrical outlets with parameters indicated on the adapter.
Do not open the cover of the device! Unplug the device before dusting and
cleaning. Use a damp cloth to clean the device. Do not use liquid/aerosol
cleaners or magnetic/static cleaning devices. Prevent moisture getting into the
device or the power adapter.
The service life of the device is 2 years.
67
DSL-G2452GR
Quick Installation Guide
TECHNICAL SUPPORT
You can find software updates and user documentation on our website.
D-Link provides its customers with free support within the product's
warranty period.
Customers can contact the technical support group by phone or by email/Internet.
FOR TELEPHONE NUMBERS AND ADDRESSES OF D-LINK
OFFICES WORLDWIDE VISIT
http://www.dlink.com
Version 4.0.1
2021-11-16
68
">