OWNER’S MANUAL

BOTTOM FREEZER

REFRIGERATOR

Read this owner’s manual thoroughly before operating the appliance and keep it handy for reference at all times.

ENGLISH

LRDCS2603*

MFL67851408

Rev.00_112019

www.lg.com

Copyright © 2019 LG Electronics Inc. All Rights Reserved.

TABLE OF CONTENTS

4 SAFETY INSTRUCTIONS

4 SAFETY INSTRUCTIONS

4 WARNING

7 CAUTION

8 PRODUCT OVERVIEW

8 Product Features

11 INSTALLATION

28

29

30

30

25

26

27

27

30

31

11 Before Installing

12 Choosing the Proper Location

14 Removing/Assembling the Handles

15 Removing/Assembling the Doors and Drawers

18 Reversing Door Opening Direction

20 Connecting the Water Line

24 Leveling

24 Turning on the Power

25 OPERATION

Before Use

Control Panel

Sabbath Mode

Automatic Icemaker

Storing Food

Humidity Controlled Crispers

Glide‘N’Serve

Refrigerator Shelves

Door Bins

Durabase

32 SMART FUNCTIONS

32 Smart Functions (Smart Diagnosis)

33 MAINTENANCE

33 Cleaning

34 Water Filter

38 TROUBLESHOOTING

38 FAQs

39 Before Calling for Service

46 LIMITED WARRANTY

46

50

For USA

For Canada

3

4

SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

Safety Messages

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and follow all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or injure you and others. All safety messages will follow the safety alert symbol and either the word WARNING or CAUTION.

These words mean:

WARNING

You may be killed or seriously injured if you do not follow instructions.

CAUTION

You may be injured or cause damage to the product if you do not follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what may happen if the instructions are not followed.

WARNING

WARNING

• To reduce the risk of explosion, fire, death, electric shock, scalding or injury to persons when using this product, follow basic precautions, including the following:

Installation

• To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including the use of long-sleeved gloves and safety glasses.

• Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.

• Only connect this product to a dedicated grounded electrical outlet rated for use with this product (115

V, 60 Hz AC only). It is the user’s responsibility to replace a standard 2-prong wall outlet with a standard

3-prong wall outlet.

• Do not use an outlet that can be turned off with a switch. Do not use an extension cord.

• The appliance must be positioned for easy access to a power source.

• When moving the refrigerator, be careful not to roll over or damage the power cord.

• Contact an authorized service center when installing or relocating the refrigerator.

• Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

• Keep packing materials out of the reach of children. Packaging material can be dangerous for children.

There is a risk of suffocation.

• Do not install the refrigerator in a damp or dusty place where insulation on electrical parts may deteriorate.

• Do not place the refrigerator in direct sunlight or expose it to the heat from heating appliances such as stoves or heaters.

• Do not bend or pinch the power cord excessively or place heavy objects on it.

SAFETY INSTRUCTIONS

5

Operation

• This appliance is intended to be used in household and similar applications such as :

- staff kitchen areas in shops, offices and other working environments;

- farm houses and by clients in hotels, motels and other residential type environments;

- bed and breakfast type environments;

- catering and similar non-retail applications.

• This product is not to be used for special purposes such as the storage of medicine or test materials or for use on ships, etc.

• DO NOT allow children to climb, stand, or hang on the refrigerator doors or on the shelves in the refrigerator. They could damage the refrigerator and seriously injure themselves.

• Do not allow children to climb into the refrigerator. They could be trapped and suffocated.

• Children should be supervised to ensure that they do not play with the refrigerator.

• Keep fingers out of pinch point areas; clearances between the doors and cabinets are necessarily small.

Be careful closing doors when children are nearby.

• Do not touch frozen food or the metal parts in the freezer compartment with wet or damp hands. Doing so may cause frostbite.

• Do not refreeze frozen food that has thawed completely. Doing so may result in a serious health hazard.

• Do not use an adapter plug or plug the power plug into a multi-outlet extension cord.

• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

• Do not operate the refrigerator or touch the power cord with wet hands.

• Do not modify or extend the power cord.

• Do not use an uncertified power outlet. Do not plug appliance into a damaged wall outlet.

• Do not put hands, feet or other objects into the air vents or bottom of the refrigerator. Doing so could result in personal injury or electric shock.

• In the event of a gas leak (propane/LPG), ensure the area is adequately ventilated and contact an authorized service center before resuming use. Do not touch the refrigerator or power cord of the refrigerator.

• Disconnect the power cord immediately and contact an authorized service center if there is a strange noise, odor, or smoke coming from the appliance.

• Do not use any fuse (such as copper, steel wire, etc.) other than a standard fuse.

• Do not place or use an electrical appliance inside the refrigerator, unless it is of a type recommended by the manufacturer.

• Do not put animals inside the appliance.

• Do not place heavy or fragile objects, liquid filled containers, combustible substances, or flammable objects (such as candles and lamps) on the appliance.

• Avoid contact with any moving parts of the ejector mechanism or with the heater that releases the ice cubes.

• If connected to a circuit protected by fuses, use time delay fuse.

• Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.

• Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.

• Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.

• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

• DO NOT place fingers in the automatic icemaker when the refrigerator is plugged in.

• When dispensing ice from the dispenser, do not use a fragile container.

6

SAFETY INSTRUCTIONS

Maintenance

• Do not use a hair dryer to dry the inside of the refrigerator.

• Do not light a candle to remove odors in the refrigerator.

• In the event of a refrigerant leak, move flammable objects away from the refrigerator. Ensure the area is adequately ventilated and contact an authorized service center.

• Keep flammable materials and vapors, such as gasoline, away from the refrigerator.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Unplug the power plug before cleaning or repairing the refrigerator.

• The refrigerator and freezer compartment lights are interior LED lighting, and service should be performed by a qualified technician.

• Unplug the power plug immediately in the event of a blackout or thunderstorm.

• Turn the power off if water or dust penetrates into the refrigerator. Call a service agent.

• Do not store glass containers or soda in the freezer compartment. Contents may expand when frozen, break the container and cause injury.

• Do not store, disassemble or repair the appliance yourself or allow unqualified personnel to do so.

• Do not bend or pinch the power cord excessively or place heavy objects on it.

Disposal

• Junked or abandoned refrigerators are dangerous, even if they are sitting for only a few days. When disposing of the refrigerator, remove the packing materials from the door or take off the doors but leave the shelves in place so that children may not easily climb inside.

• If disposing of a refrigerator, make sure the refrigerant and insulation foam are removed for proper disposal by a qualified servicer. If you release the refrigerant or throw away the insulation foam, you may be fined or imprisoned in accordance with the relevant environmental law. Insulation foam contains flammable blowing gas.

• When discarding the appliance, remove the door gasket while leaving the shelves and baskets in place, and keep children away from the appliance.

Grounding Instructions

• Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service personnel if you are in doubt whether the appliance is properly grounded. Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

• Have a certified electrician check the wall outlet and wiring for proper grounding.

• Never unplug the appliance by pulling on the power cord. Always grip the plug firmly and pull straight out from the outlet. Failure to do so may damage the power cord, resulting in a risk of fire and electric shock.

SAFETY INSTRUCTIONS

7

Risk of Fire and Flammable Materials

This appliance contains a small amount of isobutane refrigerant (R600a), which is combustible.

When transporting and installing the appliance, care should be taken to ensure that no parts of the refrigerating circuit are damaged. Refrigerant squirting out of the pipes could ignite or cause an eye injury. If a leak is detected, avoid any naked flames or potential sources of ignition and air the room in which the appliance is standing for several minutes.

In order to avoid the creation of a flammable gas air mixture if a leak in the refrigerating circuit occurs, the size of the room in which the appliance may be sited depends on the amount of refrigerant used. The room must be 10.8 square feet (1 square meter) in size for every 8g of R600a refrigerant inside the appliance. The amount of refrigerant in your particular appliance is shown on the identification plate inside the appliance. Never start up an appliance showing any signs of damage. If in doubt, consult your dealer.

CAUTION

CAUTION

• To reduce the risk of minor or moderate injury to persons, malfunction, or damage to the product or property when using this product, follow basic precautions, including the following:

Installation

• Do not install the refrigerator where there may be a danger of the unit falling.

• The refrigerator must be properly installed in accordance with the Installation Instructions.

Operation

• Do not use aerosols near the refrigerator.

• This appliance is intended to be used only in domestic and similar applications.

• Do not strike or apply excessive force to any glass surface. Do not touch glass surfaces if they are cracked or broken.

• Do not overfill or pack items too tightly into door bins. Doing so may cause damage to the bin or personal injury if items are removed with excessive force.

• Do not hang on to or place heavy objects on the refrigerator’s dispenser.

Maintenance

• Do not use strong detergents like wax or thinners for cleaning. Clean with a soft cloth.

• Remove foreign objects (such as dust and water) off the prongs of the power plug and contact areas. Do not use a wet or damp cloth when cleaning the plug.

• Do not spray water directly on the inside or outside of the refrigerator.

• Do not clean glass shelves or covers with warm water when they are cold. They may break if exposed to sudden temperature changes

SAVE THESE INSTRUCTIONS

8

PRODUCT OVERVIEW

PRODUCT OVERVIEW

Product Features

The images in this guide may be different from the actual components and accessories, which are subject to change by the manufacturer without prior notice for product improvement purposes.

Exterior

Refrigerator

Fresh food compartment

Handle

Opens and closes the refrigerator door.

Freezer

Frozen food compartment

Interior

PRODUCT OVERVIEW

9

LED Interior Lighting

Lights up the inside of the refrigerator.

Water Filter*

Purifies water.

Replace the water filter every six months. See the Replacing the Water Filter section in this manual for details.

Adjustable Refrigerator Shelf

The refrigerator shelves are adjustable to meet individual storage needs.

Humidity Controlled Crisper

Helps vegetables and fruit to stay crisp and controls humidity.

Glide’N’Serve

Store food items at a different temperature than the regular refrigerator area.

Automatic Icemaker (Freezer)*

Produces and stores ice automatically in the freezer compartment.

Ice Bin

Stores ice produced by the automatic icemaker.

10

PRODUCT OVERVIEW

Pullout Drawer

Provides extra storage within the freezer compartment.

Durabase and Durabase Divider

Provides storage for large food items.

Product Specifications

*The appearance and specifications listed in this manual may vary due to constant product improvements.

Electrical requirements: 115 V, 60 Hz

Min. / Max. water pressure: 20 - 120 psi (138 - 827 kPa)

Description

Net weight

Model LRDCS2603*

Standard-depth, bottom freezer

226 lb (102.5 kg)

INSTALLATION

INSTALLATION

Before Installing

Installation Overview

Please read the following installation instructions first after purchasing this product or transporting it to another location.

11

Unpacking the Refrigerator

Choosing the Proper Location

Disassembling/Assembling

Connecting the Water Line

Leveling

WARNING

• Connect to potable water supply only.

12

INSTALLATION

Unpacking the Refrigerator

WARNING

• Use two or more people to move and install the refrigerator. Failure to do so can result in back injury or other injury.

• The refrigerator is heavy. Protect the floor when moving the refrigerator for cleaning or service.

Always pull the refrigerator straight out when moving it. Do not wiggle or walk the refrigerator when trying to move it, as floor damage could occur.

• Keep flammable materials and vapors, such as gasoline, away from the refrigerator. Failure to do so can result in fire, explosion, or death.

Choosing the Proper

Location

Water

Water supply must be easily connected for the automatic icemaker.

NOTE

• The water pressure must be 20 - 120 psi or 138 -

827 kPa or 1.4 - 8.4 kgf/cm2. If the refrigerator is installed in an area with low water pressure

(below 20 psi or 138 kPa or 1.4 kgf/cm2), you can install a booster pump to compensate for the low pressure.

NOTE

• Remove tape and any temporary labels from your refrigerator before using. Do not remove any warning labels, the model and serial number label

• To remove any remaining tape or glue, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

• Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator.

• Reinstall or adjust shelves as needed.

Refrigerator shelves are installed in the shipping position. Reinstall shelves according to your individual storage needs.

Electricity

Use an individual, grounded outlet:115 Volts, 60

Hz, AC, 15 Amps minimum.

WARNING

• Do not overload house wiring and cause a fire hazard by plugging in multiple appliances in the same outlet with the refrigerator.

• To reduce the risk of electric shock, do not install the refrigerator in a wet or damp area.

Flooring

To avoid noise and vibration, the unit must be installed and leveled on a solidly constructed floor.

If required, adjust the leveling legs to compensate for the unevenness of the floor.

NOTE

• Installing on carpeting, soft tile surfaces, a platform or weakly supported structure is not recommended.

Ambient Temperature

Install this appliance in an area where the temperature is between 55 °F (13 °C) and 110 °F

(43 °C).

If the temperature around the appliance is too low or high, cooling ability may be adversely affected.

E

F

G

H

J

I

B

C

D

A

-

INSTALLATION

13

Dimensions and Clearances

• Check the dimensions of the appliance and the installation path to ensure there is sufficient room to move the refrigerator through doors or narrow openings.

• If an opening is too narrow to fit the refrigerator through, remove the refrigerator doors. See Removing/

Assembling the Doors and Drawers in this manual.

• The installation location chosen for the refrigerator should allow space behind the unit for connections and airflow and space in front to open the doors and drawers.

• Too small of a distance from adjacent items may result in lowered freezing capability and increased electricity consumption charges. Allow at least 27 inches (686 mm) in front of the refrigerator to open the doors, and at least 2 inches (51 mm) between the back of the refrigerator and the wall.

B

E

F A H

G

C

D

I

J

Dimension/Clearance

Depth without Handle

Width

Height to Top of Case

Height to Top of Hinge

Clearance

Depth without Door

Depth with Handle

Depth (Total with Freezer Drawer Open)

Depth (Total with Door Open 90°)

Front Clearance model

34” (864 mm)

32 4/5” (833 mm)

68 1/2” (1740 mm)

69 4/5” (1774 mm)

2” (51 mm)

29 4/9” (748 mm)

35” (889 mm)

53 1/3” (1355 mm)

63 1/4” (1606 mm)

33 7/8” (860 mm)

14

INSTALLATION

Removing/Assembling the

Handles

When moving the refrigerator through a narrow opening, removing the doors is preferred.

The appearance of the handles may vary from what is shown.

WARNING

• When assembling or disassembling the refrigerator handles, grasp the handle firmly to avoid dropping it.

• Do not swing the handle into nearby people or animals.

• Make sure that the bracket hole of the handle fits properly into the stopper bolt of the door.

Assemble the set screws to fix the handle into place.

• Make sure that there is not a gap between the door and handle after assembling the handle.

Tools Needed

• 3/32 in. Allen wrench

• 1/8 in. Allen wrench

• 1/4 in. Allen wrench

Removing the Refrigerator Handles

1

Loosen the set screws with a 3/32 in. Allen wrench and remove the handle.

2

Loosen the mounting fasteners that connect to the refrigerator door and handle using a ¼ in. Allen wrench, and remove the mounting fasteners.

fasteners and tightening the set screws with a 3/32 in. Allen wrench.

Removing the Refrigerator Handles

1

Loosen the set screws located on the lower side of the handle with a 1/8 in. Allen wrench and remove the handle.

2

Loosen the mounting fasteners with a 1/4 in. Allen wrench, and remove the mounting fasteners.

Assembling the Freezer Drawer

Handle

1

Assemble the mounting fasteners at both ends of the handle with a 1/4 in. Allen wrench.

2

Place the handle on the door by fitting the handle footprints over the mounting fasteners and tightening the set screws with a 1/8 in. Allen wrench.

Removing the Refrigerator Handles

1

Assemble the mounting fasteners at both ends of the handle with a 1/4 in. Allen wrench.

2

Place the handle on the door by fitting the handle footprints over the mounting

Removing/Assembling the

Doors and Drawers

If the entrance door is too narrow for the refrigerator to pass through, remove the refrigerator doors and move the refrigerator sideways through the doorway.

WARNING

• Use two or more people to remove and install the refrigerator doors and freezer drawer.

• Disconnect the electrical supply to the refrigerator before installing.

• Do not put hands, feet or other objects into the air vents or bottom of the refrigerator.

• Be careful when handling the hinge and stopper.

• Remove food and bins before detaching the doors and drawers.

• Do not hold the handle when removing or replacing the doors and drawer as the handle may come off.

Tools Needed

• 3/32 in. Allen wrench

• 1/8 in. Allen wrench

• 1/4 in. Allen wrench

• 5 mm (3/16 in) Allen wrench

Removing the Refrigerator Door

1

Remove the top hinge cover screws . Lift the hook (not visible), located at the bottom of the front side of the cover . with a flathead screwdriver.

2

Rotate the hinge lever clockwise. Lift the top hinge free of the hinge lever latch .

INSTALLATION

15

CAUTION

• When lifting the hinge, be careful that the door does not fall forward.

3

Lift the door from the middle hinge pin and remove the door.

CAUTION

• Place the door, inside facing up, on a non scratching surface.

Removing the Freezer Drawers

WARNING

• Use two or more people to remove and install the refrigerator doors and freezer drawer.

• Be careful of sharp hinges on both sides of the drawer.

• When you lay the drawer down, be careful not to damage the floor.

• Do not sit or stand on the freezer drawer.

• To prevent accidents, keep children and pets away from the drawer. Do not leave the drawer open. If the Durabase® storage bin is removed from the freezer drawer, there is sufficient space for a small child or pet to crawl inside.

16

INSTALLATION

1

Pull the drawer open to full extension.

2

Gently lift and pull out the ice bin.

CAUTION

• Do not hold the handle when removing or replacing the drawer. The handle may come off, causing personal injury.

3

Lift the front of the drawer up, then pull it straight out.

6

Hold both rails and push them in simultaneously.

4

Remove the Durabase basket from the rails.

Remove the screws from the rails at both ends.

Assembling the Freezer Drawer

1

Pull out both rails simultaneously, until they are fully extended.

5

Grip both sides of the drawer and pull it up to remove it from the rails.

2

Grasp the drawer on each side and hook the drawer supports into the rail tabs located on both sides.

CAUTION

• Do not hold the handle when removing or replacing the drawer. The handle may come off, causing personal injury.

5

INSTALLATION

Replace the ice bin in the drawer. Insert the

Durabase basket in the rail assembly.

17

3

Lower the door into its final position and insert the screws in the rails on both sides.

Assembling the Refrigerator Door

1

Make sure that the plastic sleeve is inserted in the bottom of the door. Lower the door onto the middle hinge pin.

4

Insert the drawer into the frame, and push the drawer back until it clicks into place.

2

3

Align the door with the cabinet.

Fit the hinge over the hinge lever latch and slot it into place. Rotate the lever counterclockwise to secure the hinge

4

Replace the hinge cover . Insert and tighten the cover screws .

18

INSTALLATION

Reversing Door Opening

Direction

NOTE

• To assist in the installation of the handle on the right side, place a piece of masking tape near the top of the handle before removing it.

• The appearance of the handle may vary from what is shown in the illustrations.

Removing the Refrigerator Handles

1

Loosen the set screws with a 3/32 in (2.5 mm) Allen wrench and remove the handle.

2

Loosen the mounting fasteners that connect to the refrigerator door and handle using a 1/4 in. (6.35 mm) Allen wrench, and remove the mounting fasteners.

4

Assemble the mounting fasteners at both ends of the handle using a 1/4 in.

(6.35 mm) Allen wrench.

5

Place the handle on the door by fitting the handle footprints over the mounting fasteners and tightening the set screws with a 3/32 in (2.5 mm) Allen wrench.

Reversing the Doors

1

Remove the top hinge cover screws .

Lift the hook (not visible), located at the bottom of the front side of the cover , with a at-head screwdriver.

3

Carefully loosen the plug buttons with your fingers. The buttons can be unscrewed with the fingers by rotating them counter-clockwise and continuing until they loosen and fall out The buttons were installed without pressure, and for this reason, they can be unscrewed using your index finger, thumb or both. Install the plug buttons on the left side.

2

Rotate the hinge lever clockwise. Lift the top hinge free of the hinge lever latch .

CAUTION

• When lifting the hinge, be careful that the door does not fall forward.

3

Lift the door from the middle hinge pin and remove the door.

CAUTION

• Place the door, inside facing up, on a nonscratching surface.

INSTALLATION

19

6

Use a ¼ in (6.35 mm) hex socket wrench to loosen the hinge pin and remove. Remove the two allen screw using 5 mm (3/16 in) , the phillip screw and the hinge .

7

With a flat-head screwdriver, carefully pry off and remove the cover over the bolt holes on the left side of the refrigerator.

4

Remove the four screws , the hinge pin insert and the hinge pin brackets from the bottom right side of the door.

8

Remove the outer lower decorative screw from the flange on the frame between the freezer and refrigerator doors (You will need this hole for the middle hinge bracket).

5

Reinstall the hinge pin brackets , screws

and hinge pin insert on the bottom left side of the door.

9

Turn the middle hinge bracket upside down and position it on the left side of the refrigerator and reattach using two allen screw using 5 mm (3/16 in.) and a Phillip screw.

10

Reattach middle hinge pin using a ¼ in.

(6.35 mm) socket wrench.

NOTE

• The bracket has been flipped, but the hinge pin stays in the same orientation with its hexagonal end facing upward.

20

INSTALLATION

Middle Hinge

Bracket

Middle Hinge

Pin

11

Insert the decorative screw into the outer hole on the right side of the flange. Attach the cover on the right side. Cover is forcefitted.

Decorative

Screw

Assemble the left hinge cover with the two screws .

15

Assemble the right hinge cap with the two screws.

12

Loosen the two screws and remove the left hinge cap.

13

Place the refrigerator door down over the hinge pin on the middle hinge pin bracket.

NOTE

• The left top hinge, right hinge cap and left hinge cover are provided for reversing doors.

14

Fit the hinge over the hinge lever latch and slot it into place. Rotate the lever clockwise to secure the hinge.

Connecting the Water Line

Before Beginning

This water line installation is not covered by the refrigerator warranty. Follow these instructions carefully to minimize the risk of expensive water damage.

If necessary, call a qualified plumber to correct water hammer before installing the water supply line to the refrigerator. Water banging in the pipes, or water hammer in residential plumbing can cause damage to refrigerator parts and lead to water leakage or flooding.

• Turn the icemaker OFF if the refrigerator will be used before the water line is connected.

• Do not install the icemaker tubing in areas where the ambient temperatures fall below freezing.

WARNING

• Connect to potable water supply only.

CAUTION

• To prevent burns and product damage, only connect the refrigerator water line to a cold water supply.

• Wear eye protection during installation to prevent injury.

INSTALLATION

• Power drill.

• ½ in. or adjustable wrench.

• Flat-blade and Phillips-head screwdrivers.

• Two ¼ in. outer diameter compression nuts and 2 ferrules (sleeves) to connect the copper tubing to the shutoff valve and the refrigerator water valve.

21

Water Pressure

You will need a cold water supply.

models with water filter where reverse osmosis water filtration system is connected to a cold water supply

Water Pressure

20 - 120 psi (138 - 827 kPa)

40 - 60 psi minimum to reverse osmosis system (2.8

kgf/cm2 - 4.2 kgf/ cm2, or less than 2 - 3 seconds to fill a cup of 7 oz capacity)

If the water pressure from the reverse osmosis system is less than 20 psi or 138 kPa or 1.4 kgf/ cm2 (takes more than 4 seconds to fill a cup of 7 oz or 198 cc capacity):

• Check to see if the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

• If the water pressure remains low, call a licensed, qualified plumber.

• All installations must be in accordance with local plumbing code requirements.

• If your existing copper water line has a flared fitting at the end, purchase an adapter (available at plumbing supply stores) to connect the water line to the refrigerator OR cut off the flared fitting with a tube cutter and then use a compression fitting.

• Shutoff valve to connect to the cold water line.

The shutoff valve should have a water inlet with a minimum inside diameter of 5/32 in. at the point of connection to the COLD WATER LINE.

Saddle-type shutoff valves are included in many water supply kits. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

Supplies Needed

• Copper or PEX Tubing, ¼ in. outer diameter, to connect the refrigerator to the water supply. Be sure both ends of the tubing are cut square. To determine how much tubing you need, measure the distance from the water valve on the back of the refrigerator to the water supply pipe. Then, add 8 feet (2.4 m). Be sure there is sufficient extra tubing (about 8 feet [2.4 m] coiled into 3 turns of about 10 in. [25 cm] diameter) to allow the refrigerator to move out from the wall after installation.

NOTE

• A self-piercing saddle type water valve should not be used.

22

INSTALLATION

Water Line Installation Instructions

Install the shutoff valve on the nearest frequently used drinking water line.

WARNING

• When using any electrical device (such as a power drill) during installation, be sure the device is battery-powered, double-insulated or grounded in a manner that will prevent the hazard of electric shock.

1

Shut off the main water supply.

• Turn on the nearest faucet to relieve the pressure on the line.

2

Choose the valve location.

• Choose a location for the valve that is easily accessible. It is best to connect into the side of a vertical water pipe. When it is necessary to connect into a horizontal water pipe, make the connection to the top or side, rather than at the bottom, to avoid drawing off any sediment from the water pipe.

4

Fasten the shutoff valve.

• Fasten the shutoff valve to the cold water pipe with the pipe clamp.

NOTE

• Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in

Massachusetts. Consult with your licensed plumber.

Pipe Clamp

Saddle-Type Shutoff Valve

Vertical Cold Water Pipe

5

Tighten the pipe clamp.

• Tighten the clamp screws until the sealing washer begins to swell.

NOTE

• Do not over tighten clamp or you may crush the tubing.

3

Drill the hole for the valve.

• Drill a ¼ in. hole in the water pipe using a sharp bit. Remove any burrs resulting from drilling the hole in the pipe. Be careful not to allow water to drain into the drill. Failure to drill a ¼ in. hole may result in reduced ice production or smaller cubes.

NOTE

• The hookup line cannot be white, plastic tubing.

Licensed plumbers must use only copper tubing

(NDA tubing #49595 or #49599) or Cross Link

Polyethylene (PEX) tubing.

Pipe Clamp

Inlet End

Clamp Screw

Washer

6

Route the tubing.

• Route the tubing between the cold water line and the refrigerator. Route the tubing through a hole drilled in the wall or floor

(behind the refrigerator or adjacent base cabinet) as close to the wall as possible.

NOTE

• Be sure there is sufficient extra tubing (about 8 ft. coiled into three turns of about 10 in.

diameter) to allow the refrigerator to move out from the wall after installation.

7

Connect the tubing to the valve.

• Place the compression nut and ferrule

(sleeve) for copper tubing onto the end of the tubing and connect it to the shutoff valve. Make sure the tubing is fully inserted into the valve. Tighten the compression nut securely.

9

INSTALLATION

23

Connect the tubing to the refrigerator.

NOTE

• Before making the connection to the refrigerator, be sure that the refrigerator power cord is not plugged into the wall outlet.

• Remove the plastic flexible cap from the water valve.

• Place the compression nut and ferrule (sleeve) onto the end of the tubing as shown.

NOTE

• Insert the end of the copper tubing into the connection as far as possible. While holding the tubing, tighten the fitting.

Tubing Clamp

¼ in. Tubing

¼ in. Compression Nut

Ferrule (sleeve)

Refrigerator Connection

Saddle-Type Shutoff Valve

Compression Nut

Packing Nut

Outlet Valve

Ferrule (sleeve)

8

Flush out the tubing.

• Turn the main water supply on and flush out the tubing until the water is clear. Shut the water off at the water valve after about one quart of water has been flushed through the tubing.

10

Turn the water on at the shutoff valve.

• Tighten any connections that leak.

CAUTION

• Check to see if leaks occur at the water line connections.

24

INSTALLATION

Leveling

The refrigerator has two front leveling legs. Adjust the legs to alter the tilt from front-to-back or sideto side. If the refrigerator seems unsteady, or the doors do not close easily, adjust the refrigerator’s tilt using the instructions below:

1

Turn the leveling leg to the left to raise that side of the refrigerator or to the right to lower it. It may take several turns of the leveling leg to adjust the tilt of the refrigerator.

NOTE

• A flare nut wrench works best, but an open-end wrench will suffice. Do not over-tighten.

Position the Refrigerator

• Arrange the coil of tubing so that it does not vibrate against the back of the refrigerator or against the wall. Push the refrigerator back to the wall.

Start the Icemaker

• If the water line is connected, set the icemaker power switch to the ON position.

• The icemaker will not begin to operate until it reaches its operating temperature of 10 °F (–12

°C) or below. It will then begin operation automatically if the icemaker power switch is in the ON (I) position.

2

Open both doors and check to make sure that they close easily. If the doors do not close easily, tilt the refrigerator slightly more to the rear by turning both leveling legs to the left. It may take several more turns, and be sure to turn both leveling legs the same amount.

Turning on the Power

• After installing, plug the refrigerator’s power cord into a 3-prong grounded outlet and push the refrigerator into the final position.

CAUTION

• Connect to a rated power outlet.

• Have a certified electrician check the wall outlet and wiring for proper grounding.

• Do not damage or cut off the ground terminal of the power plug.

OPERATION

25

OPERATION

Before Use

Checklist

Clean the refrigerator.

Clean the refrigerator thoroughly and wipe off all dust that accumulated during shipping.

CAUTION

• Do not scratch the refrigerator with a sharp object or use a detergent that contains alcohol, a flammable liquid or an abrasive when removing any tape or adhesive from the refrigerator. Remove adhesive residue by wiping it off with your thumb or dish detergent.

• Do not peel off the model or serial number label or the technical information on the rear surface of the refrigerator.

Open refrigerator door and freezer drawer to ventilate the interior.

The inside of the refrigerator may smell like plastic at first. Remove any adhesive tape from inside the refrigerator and open the refrigerator door and the freezer drawer for ventilation.

Connect the power supply.

Check if the power supply is connected before use.

Turn off the icemaker.

Turn off the icemaker if the refrigerator is not yet connected to the water supply.

NOTE

• The icemaker water valve may buzz if the icemaker is turned on while the refrigerator is not connected to the water supply.

Wait for the refrigerator to cool.

Allow the refrigerator to run for at least two to three hours before putting food in it. Check the flow of cold air in the freezer compartment to ensure proper cooling.

CAUTION

• Putting food in the refrigerator before it has cooled could cause the food to spoil, or a bad odor to remain inside the refrigerator.

The refrigerator makes a loud noise after initial operation.

This is normal. The volume will decrease as the temperature decreases.

26

OPERATION

Control Panel

Depending on the model, some of the following functions may not be available.

The actual control panel may differ from model to model.

Control Panel Features

Freezer

Indicates the set temperature of the freezer compartment in Celsius (°C) or Fahrenheit (°F). The default freezer temperature is 0°F (-18 °C). Press the Freezer button repeatedly to select a new set temperature from 5 °F to -7 °F (-23 °C to -15 °C).

Refrigerator

Indicates the set temperature of the refrigerator compartment in Celsius (°C) or Fahrenheit (°F). The default refrigerator temperature is 37 °F (3 °C). Press the Refrigerator button repeatedly to select a new set temperature from 43 °F to 33 °F (7 °C to 1 °C).

NOTE

• To change the temperature mode from °F to °C (or vice versa) press and hold the Refrigerator and

Freezer buttons simultaneously for approximately five seconds. The temperature indicator on the display window switches between Celsius and Fahrenheit.

• The displayed temperature is the target temperature, and not the actual temperature of the refrigerator.

The actual refrigerator temperature depends on the food inside the refrigerator.

Water Filter Replace

Replace the water filter when the Water Filter Replace indicator turns on. After replacing the water filter, press and hold the Water Filter Replace button for three seconds to turn the indicator light off. Replace the water filter approximately every six months.

Ice Plus

This function increases both ice making and freezing capabilities.

Press the Ice Plus button to illuminate the icon and activate the function for 24 hours. The function automatically shuts off after 24 hours. Stop the function manually by pressing the button once more.

CAUTION

Display Mode (For Store Use Only)

• The Display Mode disables all cooling in the refrigerator and freezer sections to conserve energy while on display in a retail store. When activated, OFF is displayed on the control panel and the display remains on for 20 seconds.

• To deactivate / activate:

- With either refrigerator door opened, press the Express Frz.

button 3 times consecutively while

pressing the Refrigerator button. The control panel beeps and the temperature settings display to

confirm that Display Mode is deactivated. Use the same procedure to activate Display Mode.

NOTE

• When the refrigerator is in the Power Saving Mode, the display remains off until a door is opened or a button is pressed. Once on, the display remains on for 20 seconds.

Sabbath Mode

Using the Sabbath Mode

Sabbath mode is used on the Jewish Sabbath and holidays.

• To turn Sabbath mode on, touch the display to activate it, then press and hold the Freezer and

Water Filter replace buttons for 3 seconds until

Sb appears in the display.

• To turn Sabbath mode off manually, press and hold the shabbath button for 3 seconds.

NOTE

• Sabbath mode automatically turns off after 96 hours.

• Once turned on, Sabbath mode is maintained even after a power outage.

• Selecting Sabbath mode automatically turns off the Alarm functions. The display is disabled in

Sabbath Mode.

Automatic Icemaker

Freezer Icemaker

This feature is only available on some models.

The feature may vary depending on model purchased.

Auto Shutoff (feeler arm)

Power Switch

NOTE

• The icemaker produces ice once approximately

48 hours have passed after the appliance is initially installed.

• Throw away the first few batches of ice (about

140 - 160 cubes) after installation.This is also necessary if the refrigerator has not been used for a longtime.

• The automatic freezer icemaker produces 12 cubes at a time, 50-110 pieces within a 24 hour period if conditions are favorable. This amount may vary according to the environment (ambient

OPERATION

27

temperature around the appliance, frequency of the door being opened, amount of food stored in the appliance, etc.).

• The amount and shape of ice may vary according to the environment (ambient temperature around the appliance, frequency of the door being opened, amount of food stored in the appliance, water pressure, etc.).

• The sound of ice dropping into the ice bin is normal.

• If the ice bin is completely filled with ice, ice production will stop.

• In the event of a power outage, throw away the ice stored in the ice bin.

• Ice cubes which are stored in the ice bin for a long time may clump together and be difficult to separate. If this happens, empty the ice bin completely and clean it before reinstalling it.

Turning the Automatic Icemaker

On

To turn the automatic icemaker On/Off, press the power switch on the icemaker to the ON ( | ) or

OFF (O) position.

Normal Sounds You May Hear

• Keeping the power turned on to the icemaker before the water line is connected can damage the icemaker.

• The icemaker water valve buzzes as the icemaker fills with water. If the icemaker power button is in the ON mode, it will buzz even if it has not yet been hooked up to water. To stop the buzzing, press the icemaker power button to turn it off.

• You will hear the sound of cubes dropping into the bin and water running in the pipes as the icemaker refills.

Preparing for Vacation

Set the icemaker power button to OFF and shut off the water supply to the refrigerator.

NOTE

• The ice bin should be emptied any time the icemaker power button is turned to the OFF mode.

If the ambient temperature will drop below freezing, have a qualified technician drain the

28

OPERATION water supply system to prevent serious property damage due to flooding caused by ruptured water lines or connections

Storing Food

Food Storage Tips

Wrap or store food in the refrigerator in airtight and moisture-proof material unless otherwise noted. This prevents food odor and taste transfer throughout the refrigerator. For dated products, check date code to ensure freshness.

CAUTION

• Do not overfill or pack items too tightly into door bins. Doing so may cause damage to the bin or personal injury if items are removed with excessive force.

• Do not store glass containers in the freezer.

Contents may expand when frozen, break the container and cause injury.

Food

Butter or

Margarine

Cheese

Milk

Eggs

Fruit

Leafy

Vegetables

Vegetables with skins

(carrots, peppers)

How to Store

Keep opened butter in covered dish or closed compartment. When storing an extra supply, wrap in freezer packaging and freeze.

Store in original wrapping until used.

Once opened, rewrap tightly in plastic wrap or aluminum foil.

Wipe milk cartons. For coldest milk, place containers on an interior shelf.

Store in original carton on interior shelf, not on door shelf.

Do not wash or hull fruit until it is ready to be used. Sort and keep fruit in original container in a crisper, or store in completely closed paper bag on refrigerator shelf.

Remove store wrapping, trim or tear off bruised and discolored areas, wash in cold water, and drain. Place in plastic bag or plastic container and store in crisper.

Place in plastic bags or plastic container and store in crisper.

Food

Fish

Leftovers

How to Store

Freeze fresh fish and shellfish if they are not being eaten the same day purchased. Eating fresh fish and shellfish the same day purchased is recommended.

Cover leftovers with plastic wrap or aluminum foil, or store in plastic containers with tight lids.

Storing Frozen Food

Check a freezer guide or a reliable cookbook for further information about preparing food for freezing or food storage times.

Freezing

Your freezer will not quick-freeze a large quantity of food. Do not put more unfrozen food into the freezer than will freeze within 24 hours (no more than 2 to 3 pounds of food per cubic foot of freezer space). Leave enough space in the freezer for air to circulate around packages. Be careful to leave enough room at the front so the door can close tightly.

Storage times will vary according to the quality and type of food, the type of packaging or wrap used (how airtight and moisture-proof) and the storage temperature. Ice crystals inside a sealed package are normal. This simply means that moisture in the food and air inside the package have condensed, creating ice crystals.

NOTE

• Allow hot foods to cool at room temperature for

30 minutes, and then package and freeze.

Cooling hot foods before freezing saves energy.

Packaging

Successful freezing depends on correct packaging.

When you close and seal the package, it must not allow air or moisture in or out. If it does, you could have food odor and taste transfer throughout the refrigerator and could also dry out frozen food.

Packaging recommendations

• Rigid plastic containers with tight-fitting lids

• Straight-sided canning/freezing jars

• Heavy-duty aluminum foil

• Plastic-coated paper

• Non-permeable plastic wraps

• Specified freezer-grade self-sealing plastic bags

Follow package or container instructions for proper freezing methods.

Do not use

• Bread wrappers

• Non-polyethylene plastic containers

• Containers without tight lids

• Wax paper or wax-coated freezer wrap

• Thin, semi-permeable wrap

NOTE

• If you are leaving home for a short period, like a short vacation, the refrigerator should be left on.

Refrigerated foods that are able to be frozen will stay preserved longer if stored in the freezer.

• If you are leaving the refrigerator turned off for an extended period, remove all food and unplug the power cord. Clean the interior, and leave the door open to prevent fungi from growing in the refrigerator.

• Do not store food with high moisture content towards the top of the refrigerator. The moisture could come in direct contact with the cold air and freeze.

• Wash food before storing it in the refrigerator.

Vegetables should be washed, and food packaging should be wiped down to prevent adjacent foods from being contaminated.

• If the refrigerator is kept in a hot and humid place, frequent opening of the door or storing a lot of vegetables in the refrigerator may cause condensation to form. Wipe off the condensation with a clean cloth or a paper towel.

• If the refrigerator door or freezer drawer is opened or closed too often, warm air may penetrate the refrigerator and raise its temperature. This can increase the running costs of the unit.

OPERATION

• Vegetables keeps moist air in the crisper for best storage of fresh, leafy vegetables.

• Fruit lets moist air out of the crisper for best storage of fruit.

29

Removing/Assembling the

Humidity Controlled Crispers

1

2

3

Pull out the crisper to full extension, lift the front up, and pull straight out.

Lift the front of the cover up with both hands until it detaches from the back wall of the cabinet, then pull it out.

To reassemble, insert the cover into the refrigerator with both hands and lower it onto the guides.

Humidity Controlled

Crispers

Using the Humidity Controlled

Crispers

This feature is only available on some models.

The crispers provide fresher tasting fruit and vegetables by letting you easily control humidity inside the drawer.

You can control the amount of humidity in the moisture-sealed crispers by adjusting the control to any setting between Vegetables and Fruit.

4

Slightly tilt up the front, insert the crisper into the frame and push it back into place.

30

OPERATION

Glide‘N’Serve

Using the Glide‘N’Serve

This drawer can be used for large party trays, deli items and beverages. This drawer should not be used to store vegetables that require high humidity.

CAUTION

• Do not place any items on the Glide‘N’Serve cover.

Detaching/Assembling the Full

Width Shelf

CAUTION

• Do not clean glass shelves with warm water while they are cold. Shelves may break if exposed to sudden temperature changes or impact.

1

To detach, lift the rear of the shelf and pull it out.

Detaching/Assembling the

Glide‘N’Serve

1

To remove the Glide’N’Serve, pull out the

Glide’N’Serve to full extension, lift the front up, and pull straight out.

2

To assemble, slide the shelf in the guides until it stops.

2

To assemble, slightly tilt up the front, insert the Glide’N’Serve into the frame and push it back into place.

Refrigerator Shelves

The shelves in the refrigerator are adjustable to meet individual storage needs. Your model may have full or split shelves.

Adjusting the shelves to fit items of different heights will make finding the exact item you want easier.

Door Bins

Detaching/Assembling the Door

Bins

CAUTION

• Regularly detach and wash the storage bins and shelves; they can become easily contaminated by food.

• Do not apply excessive force while detaching or assembling the storage bins.

• Do not use the dishwasher to clean the storage bins and shelves.

The door bins are removable for easy cleaning and adjustment.

1

To remove the bin, simply lift the bin up and pull straight out.

2

To replace the bin, slide it in above the desired support and push down until it snaps into place.

Durabase

Using the Durabase

CAUTION

• If the Durabase divider is removed, there is enough open space for children or pets to crawl inside. To prevent accidental child and pet entrapment or suffocation risk, DO NOT allow children or pets to touch or go near the drawer.

The Durabase divider allows you to organize the

Durabase area into 2 sections. It can be adjusted from side to side to accommodate items of different sizes.

OPERATION

31

32

SMART FUNCTIONS

SMART FUNCTIONS

LG ThinQ Application

This feature is only available on models with the or logo.

The LG ThinQ application allows you to communicate with the appliance using a smartphone.

LG ThinQ Application Features

Communicate with the appliance from a smartphone using the convenient smart features.

Smart Diagnosis

• If you experience a problem while using the appliance, this smart diagnosis feature will help you diagnose the problem.

NOTE

• The application is subject to change for appliance improvement purposes without notice to users.

• Functions may vary by model.

NOTE

• For reasons not attributable to LGE’s negligence, the service may not operate due to external factors such as, but not limited to, Wi-Fi unavailability, Wi-Fi disconnection, local app store policy, or app unavailability.

• The feature may be subject to change without prior notice and may have a different form depending on where you are located.

Using Audible Diagnosis to

Diagnose Issues

Follow the instructions below to use the audible diagnosis method.

• Launch the LG ThinQ application and select the

Smart Diagnosis feature in the menu. Follow the instructions for audible diagnosis provided in the

LG ThinQ application.

1

Open the refrigerator door.

2

Press and hold the Freezer button for 3 seconds or longer.

• The control panel will be turned off, and then ‘3’ will be displayed on the fridge temperature display part.

Installing the LG ThinQ

Application

Search for the LG ThinQ application from the

Google Play Store or Apple App Store on a smart phone.

• Follow instructions to download and install the application.

• Run the LG ThinQ application and follow the instructions in the application to register the appliance.

3

Hold the phone on the upper right speaker hole.

Smart Diagnosis

4

After the data transfer is complete, the diagnosis will be displayed in the application.

This feature is only available on models with the or logo.

Use this feature to help you diagnose and solve problems with your appliance.

NOTE

• For best results, do not move the phone while the tones are being transmitted.

MAINTENANCE

33

MAINTENANCE

Cleaning

WARNING

• Use non-flammable cleaner. Failure to do so can result in fire, explosion, or death.

CAUTION

• Do not use an abrasive cloth or sponge when cleaning the interior and exterior of the refrigerator.

• Do not place your hand on the bottom surface of the refrigerator when opening and closing the doors.

• When lifting the hinge free of the latch, be careful that the door does not fall forward.

General Cleaning Tips

• Both the refrigerator and freezer sections defrost automatically; however, clean both sections once a month to prevent odors.

• Wipe up spills immediately.

• Unplug the refrigerator or disconnect power before cleaning.

• Remove all removable parts, such as shelves.

• Use a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners.

• Hand wash, rinse and dry all surfaces thoroughly.

Exterior

Waxing external painted metal surfaces helps provide rust protection. Do not wax plastic parts.

Wax painted metal surfaces at least twice a year using appliance wax (or auto paste wax). Apply wax with a clean, soft cloth.

For products with black stainless steel exterior, spray glass cleaner on a clean, microfiber cloth and rub in direction of grain. Do not spray glass cleaner directly at the display panel. Do not use harsh or abrasive cleaners.

For products with a standard stainless steel exterior, use a damp microfiber cloth and rub in the direction of the grain. Dry with a paper towel to avoid streaks. For stubborn stains and fingerprints, use a few drops of liquid dish soap in water, and rinse with hot water before drying. Do not use abrasive or harsh cleaners.

Inside Walls

• Allow freezer to warm up so the cloth will not stick.

To help remove odors, wash the inside of the refrigerator with a mixture of baking soda and warm water. Mix 2 tablespoons of baking soda to 1 quart of water (26 g soda to 1 liter water.) Be sure the baking soda is completely dissolved so it does not scratch the surfaces of the refrigerator.

Door Liners and Gaskets

Use a clean sponge or soft cloth and a mild detergent in warm water. Do not use cleaning waxes, concentrated etergents, bleaches, or cleaners containing petroleum on plastic refrigerator parts.

Plastic Parts (Covers and Panels)

Use a clean sponge or soft cloth and a mild detergent in warm water. Do not use glass cleaners, abrasive cleansers, or flammable fluids.

These can scratch or damage the material.

Condenser Coils

Use a vacuum cleaner with a brush or crevice attachment to clean the condenser cover and vents. Do not remove the panel covering the condenser coil area.

34

MAINTENANCE

Water Filter

Before Replacing the Water Filter

WARNING

• To reduce the risk associated with choking, do not allow children under 3 years of age to have access to small parts during the installation of this product.

• To reduce the risk associated with the ingestion of contaminants, do not use with water that is microbiologicallyunsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts.

• Use of unauthorized water filters may result in product malfunction, water leakage or water quality issues, which will not be covered under the product warranty.

• Ensure all tubing and fittings are secure and free of leaks.

Replacing the Water Filter

`Replace the water filter:

• Approximately every six months.

• When the Water Filter Replace icon turns on.

• When the ice maker output decreases.

To purchase a replacement water filter:

• Visit your local dealer or distributor

• Search using “water filter”on lg.com

• Use replacement cartridge: LT1000P, LT1000PC or LT1000PCS

1

If the top shelf, located below the water filter, is in the highest position, it will need to be removed prior to replacing the water filter.

• To remove the shelf, lift the rear of the shelf and pull it out.

CAUTION

• Read and follow Use Instructions before installation and use of this system.

• Installation and use MUST comply with all state and local plumbing codes.

• Do not install if water pressure exceeds 120 psi

(827 kPa). If your water pressure exceeds 80 psi, you must install a pressure limiting valve.

Contact a plumber if uncertain how to check your water pressure.

• Do not install where water hammer conditions may occur. If water hammer conditions exist you must install a water hammer arrester. Contact a plumbing professional if you are uncertain how to check for this condition.

• Do not install on hot water supply lines. The maximum operating water temperature of this filter system is 100 °F (37.8 °C).

• Protect filter from freezing. Drain filter when temperatures drop below 40 °F (4.4 °C).

• The disposable filter cartridge MUST be replaced every 6 months, at the rated capacity or if a noticeable reduction in flow rate occurs.

• Protect from freezing, remove filter cartridge when temperatures are expected to drop below

33° F.

• Do not install systems in areas where ambient temperatures may go above 110° F (43.3° C).

• Where a backflow prevention device is installed on a water system, a device for controlling pressure due to thermal expansion must be installed.

2

Remove the old water filter.

• Lower or remove the top left shelf to allow the water filter to rotate all the way down.

Pinch the sides to open the water filter cover.

NOTE

• Replacing the water filter causes a small amount of water (around 1 oz. or 25 cc) to drain.

• Wrap a cloth around the front end of the water filter cover to collect any leaking water. Hold the water filter upright, once it is removed, to prevent any remaining water from spilling out of the water filter.

3

Pull the water filter downward and turn it counterclockwise before pulling it out. Make sure to rotate the filter down completely before pulling it out of the manifold hole.

For further assistance, call:

• 1-800-243-0000 (USA)

• 1-888-542-2623 (Canada)

MAINTENANCE

35

4

Replace with a new water filter.

• Take the new water filter out of its packing and remove the protective cover from the orings.

With the water filter tabs in the horizontal position, push the new water filter into the manifold hole and turn it clockwise until it stops.

5

Close the water filter cover. The cover will click when closed correctly.

6

After the water filter is replaced, dispense 2.5

gallons of water (flush for approximately 5 minutes) to remove trapped air and contaminants from the system.

NOTE

• Do not dispense the entire 2.5 gallon amount continuously. Press and release the dispenser pad for cycles of 30 seconds ON and 60 seconds

OFF.

7

After changing the filter, press and hold the

Water Filter Replace button for three seconds to reset the indicator light.

36

MAINTENANCE

Before Replacing the Water Filter

Model: LT1000P, LT1000PC, LT1000PCS

NSF System Trade Name Code: MDJ64844601

The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system as specified in NSF/

ANSI Standard 42, Standard 53 and Standard 401.

System tested and certified by NSF International against NSF/ANSI Standard 42, Standard 53 and

Standard 401 for the reduction of substances listed below.

Substance

Reduction

Average

Influent

Challenge

2.0 μg/L

NSF specified

Challenge

Concentration

2.0 μg/L± 10%

Avg %

Reduction

Chlorine Taste and

Odor

Nominal Particulate

Class I, , ≥ 0.5 to <

1.0 μm

Asbestos

12,000,000 pts/mL

12,000,000 pts/mL

>97.5%

99.80%

180 MFL >99.00%

Atrazine

Benzene

Carbofuran

Lindane

P-Dichlorobenzene

2,4-D

Lead pH @6.5

Lead pH @8.5

Mercury @ pH6.5

Mercury @ pH8.5

Cyst*

Atenolol

Carbamazepine

DEET

Trimethoprim

Linuron

Phenytoin

Ibuprofen

Naproxen

Estrone

100,000 cysts/L

240 ng/L

1600 ng/L

1600 ng/L

170 ng/L

160 ng/L

200 ng/L

400 ng/L

140 ng/L

8.5 μg/L

15.0 μg/L

74.0 μg/L

1.9 μg/L

230.0 μg/L

210.0 μg/L

140.0 μg/L

150.0 μg/L

5.9 μg/L

5.6 μg/L

120 ng/L

> 95.50%

98.40%

97.10%

>96.80%

>96.60%

>94.80%

>94.50%

>96.10%

>96.10%

Bisphenol A 2000 ng/L 2000 ± 40% ng/L >98.90%

Nonyl Phenol 1600 ng/L 1400 ± 40% ng/L

• Based on the use of Cryptosporidium parvum oocysts.

>97.10%

10 7 to 10 length

8 MFL; fibers greater than 10 μg/Lin

9.0 μg/L ± 10%

15.0 μg/L ± 10%

80.0 μg/L ± 10%

2.0 μg/L ± 10%

225.0 μg/L ± 10%

210.0 μg/L ± 10%

150.0 μg/L ± 10%

150.0 μg/L ± 10%

6.0 μg/L ± 10%

6.0 μg/L ± 10%

Minimum 50,000 cysts/L

200 ± 40% ng/L

1400 ± 40% ng/L

1400 ± 40% ng/L

140 ± 40% ng/L

140 ± 40% ng/L

200 ± 40% ng/L

400 ± 40% ng/L

140 ± 40% ng/L

140 ± 40% ng/L

>94.10%

>96.60%

98.30%

>99.00%

>99.80%

>99.90%

99.60%

>99.70%

91.00%

92.5%

>99.99%

Average

Product Water

Concentration

0.050 μg/L

24,000 pts/ml

< 1 MFL

0.500 μg/L

0.510 μg/L

1.258 μg/L

0.019 μg/L

0.460 μg/L

0.210 μg/L

0.560 μg/L

<0.500 μg/L

0.531 μg/L

0.420 μg/L

10 cysts/L

10.80 ng/L

25.60 ng/L

46.40 ng/L

5.44 ng/L

5.44 ng/L

10.40 ng/L

22.00 ng/L

5.46 ng/L

4.68 ng/L

22.00 ng/L

46.40 ng/L

Max Permissible

Product Water

Concentration

N/A

NSF

Reduction

Requirements

≥ 50.00%

N/A

N/A

30 ng/L

200 ng/L

200 ng/L

20 ng/L

20 ng/L

30 ng/L

60 ng/L

20 ng/L

20 ng/L

300 ng/L

200 ng/L

3.0 μg/L

5.0 μg/L

40 μg/L

0.2 μg/L

75.0 μg/L

70.0 μg/L

10.0 μg/L

10.0 μg/L

2.0 μg/L

2.0 μg/L

N/A

≥ 85.00%

≥ 99.00%

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

≥ 99.95%

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

MAINTENANCE

37

Guidelines for Application / Water Supply Parameters

Service Flow

Water Supply

Water Pressure

Water Temperature

Capacity

0.5 gpm (1.9 lpm)

Community or Private Well - Potable Water

20 – 120 psi (138 – 827 kPa)

33 °F – 100 °F (0.6 °C – 37.8°C)

200 gallons (757 liters)

It is essential that the manufacturer’s recommended installation, maintenance and filter replacement requirements be carried out for the product to perform as advertised.

NOTE

• While the testing was performed under standard laboratory conditions, actual performance may vary.

For replacement filters, visit your local dealer or distributor or search under “water filters” on the lg.com

website.

For further assistance, contact the LG Electronics Customer Information Center.

USA: 1-800-243-0000

Canada: 1-888-542-2623

Replacement Cartridge: LT1000P, LT1000PC or LT1000PCS

LG is a trademark of LG corp.

NSF is a trademark of NSF International.

Manufactured by LG Electronics, INC:

170, Sungsanpaechoungro, Seongsan-gu, Gyeongsangnam-do, THE REPUBLIC OF KOREA

38

TROUBLESHOOTING

TROUBLESHOOTING

FAQs

Frequently Asked Questions

Q:

A:

What are the best temperature settings for my refrigerator and freezer?

The default setting for the refrigerator is 37° Fahrenheit (3° Celsius). The default setting for the freezer is 0° Fahrenheit (-18° Celsius). Adjust these settings as necessary to keep food at desired temperatures. Milk should be cold when stored on the inner shelf of the refrigerator. Ice cream should be firm and ice cubes should not melt in the freezer. To switch the display from Fahrenheit to

Celsius, press and hold the Freezer and Refrigerator buttons until you hear a beep and the settings in the display change.

Q:

A:

Q:

A:

Q:

A:

Q:

A:

How do I set the refrigerator and freezer temperatures?

Continually press the Refrigerator or Freezer button on the control panel until the desired temperature appears. The numbers will cycle from highest to lowest and then return to the highest again with continuous pressing.

Why do I hear a buzzing noise from my refrigerator periodically?

This may happen if you do not have a water source attached to your refrigerator and the icemaker is turned on. If you do not have a water source attached to the back of the refrigerator you should turn the icemaker off.

Why does the icemaker tray look crooked?

This is a normal part of the icemaker cycle. The icemaker tray may appear level or with a slight tilt.

The change in position is to assist in the freezing process.

My refrigerator is powered on and the controls are working, but it’s not cooling and the display shows “OFF” (see below). What is wrong?

The refrigerator is in Display Mode. The Display Mode disables all cooling in the refrigerator and freezer sections to conserve energy while on display in a retail store. When activated, OFF is displayed on the control panel and the display remains on for 20 seconds. With either refrigerator door opened, press the Ice Plus button 3 times consecutively while pressing the Refrigerator button. The control panel beeps and the temperature settings display to confirm that Display Mode is deactivated. Use the same procedure to activate Display Mode.

TROUBLESHOOTING

39

Before Calling for Service

Cooling

Problem

Refrigerator and

Freezer section are not cooling.

Cooling system runs too much.

Possible Cause & Solution

The refrigerator control is set to OFF (some models).

• Turn the control ON. Refer to the Setting the Controls section for proper temperature settings.

Refrigerator is set to Demo Mode.

• Demo Mode allows the lights and control display to work normally while disabling cooling, to save energy while the refrigerator is on the showroom floor. See the FAQs section of this manual for instructions on how to disable Demo Mode.

Refrigerator is in the defrost cycle.

• During the defrost cycle, the temperature of each compartment may rise slightly. Wait 30 minutes and confirm the proper temperature has been restored once the defrost cycle has completed.

Refrigerator was recently installed.

• It may take up to 24 hours for each compartment to reach the desired temperature.

Refrigerator was recently relocated.

• If the refrigerator was stored for a long period of time or moved on its side, it is necessary for the refrigerator to stand upright for 24 hours before connecting it to power.

Refrigerator is replacing an older model.

• Modern refrigerators require more operating time but use less energy due to more efficient technology.

Refrigerator was recently plugged in or power restored.

• The refrigerator will take up to 24 hours to cool completely.

The door is opened often or a large amount of food / hot food was added.

• Adding food and opening the door warms the refrigerator, requiring the compressor to run longer in order to cool the refrigerator back down. In order to conserve energy, try to get everything you need out of the refrigerator at once, keep food organized so it is easy to find, and close the door as soon as the food is removed. (Refer to the Food Storage

Guide.)

Doors are not closed completely.

• Firmly push the doors shut. If they will not shut all the way, the “Doors will not close correctly or pop open” section in Troubleshooting

Refrigerator is installed in a hot location.

• The compressor will run longer under warm conditions. At normal room temperatures (70

°F or 21 °C) expect your compressor to run about 40 % to 80 % of the time. Under warmer conditions, expect it to run even more often. The refrigerator should not be operated above 110 °F (43 °C).

Condenser / back cover is clogged.

• Use a vacuum cleaner with an attachment to clean the condenser cover and vents. Do not remove the panel covering the condenser coil area.

40

TROUBLESHOOTING

Problem

Interior moisture buildup.

Food is freezing in the refrigerator compartment.

Refrigerator or

Freezer section is too cold.

Frost or ice crystals form on frozen food

(inside of sealed package).

Frost or ice crystals form on frozen food

(outside of package).

Possible Cause & Solution

Doors are opened often or for long periods of time.

• When the doors are opened often or for long periods of time, warm, humid air enters the compartment. This raises the temperature and moisture level within the compartment. To lessen the effect, reduce the frequency and duration of door openings.

Doors are not closed correctly.

• See the “Doors will not close correctly or pop open” section.

Weather is humid.

• Humid weather allows additional moisture to enter the compartments when the doors are opened leading to condensation or frost. Maintaining a reasonable level of humidity in the home will help to control the amount of moisture that can enter the compartments.

Defrost cycle recently completed.

• During the defrost cycle, the temperature of each compartment may rise slightly and condensation may form on the back wall. Wait 30 minutes and confirm that the proper temperature has been restored once the defrost cycle has completed.

Food is not packaged correctly.

• Food stored uncovered or unwrapped, and damp containers can lead to moisture accumulation within each compartment. Wipe all containers dry and store food in sealed packaging to prevent condensation and frost.

Food with high water content was placed near an air vent.

• Rearrange items with high water content away from air vents.

Refrigerator temperature control is set incorrectly.

• If the temperature is too cold, adjust the control one increment at a time and wait for the temperature to stabilize. Refer to the Control Panel section for more information.

Refrigerator is installed in a cold location.

• When the refrigerator is operated in temperature below 41 °F (5 °C), food can freeze in the refrigerator compartment. The refrigerator should not be operated in temperature below

55 °F (13 °C).

Incorrect temperature control settings.

• If the temperature is too cold, adjust the control one increment at a time and wait for the temperature to stabilize. Refer to the Control Panel for more information.

Condensation from food with a high water content has frozen inside of the food package.

• This is normal for food items with a high water content.

Food has been left in the freezer for a long period of time.

• Do not store food items with high water content in the freezer for a long period of time.

Door is opened frequently or for long periods of time.

• When the doors are opened often or for long periods of time, warm, humid air enters the compartment. This raises the temperature and moisture level within the compartment.

Increased moisture will lead to frost and condensation. To lessen the effect, reduce the frequency and duration of door openings.

Door is not closing properly.

• Refer to the “Doors will not close correctly or pop open” section in the Troubleshooting.

TROUBLESHOOTING

41

Problem

Refrigerator or

Freezer section is too warm.

Possible Cause & Solution

Refrigerator was recently installed.

• It may take up to 24 hours for each compartment to reach the desired temperature.

The air vents are blocked. Cold air circulates from the freezer to the fresh food section and back again through air vents in the wall dividing the two sections.

• Locate air vents by using your hand to sense airflow and move all packages that block vents and restrict airflow. Rearrange items to allow air to flow throughout the compartment.

Doors are opened often or for long periods of time.

• When the doors are opened often or for long periods of time, warm, humid air enters the compartment. This raises the temperature and moisture level within the compartment. To lessen the effect, reduce the frequency and duration of door openings.

Unit is installed in a hot location.

• The refrigerator should not be operated in temperatures above 110 °F (43 °C).

A large amount of food or hot food was added to either compartment.

• Adding food warms the compartment requiring the cooling system to run. Allowing hot food to cool to room temperature before putting it in the refrigerator will reduce this effect.

Doors are not closed correctly.

• See the “Doors will not close correctly or pop open” section in the Troubleshooting.

Temperature control is not set correctly.

• If the temperature is too warm, adjust the control one increment at a time and wait for the temperature to stabilize.

Defrost cycle has recently completed.

• During the defrost cycle, the temperature of each compartment may rise slightly and condensation may form on the back wall. Wait 30 minutes and confirm the proper temperature has been restored once the defrost cycle has completed.

42

TROUBLESHOOTING

Ice & Water

Problem

Icemaker is not making enough ice.

Possible Cause & Solution

Demand exceeds ice storage capacity.

• The icemaker will produce approximately 70-184 cubes in a 24 hour period.

House water supply is not connected, valve is not turned on fully, or valve is clogged.

• Connect the refrigerator to a cold water supply with adequate pressure and turn the water shutoff valve fully open. If the problem persists, it may be necessary to contact a plumber.

Water filter has been exhausted.

• Replacing the water filter is recommended:

Approximately every six months.

When the water filter indicator turns on.

When the water dispenser output decreases.

When the ice cubes are smaller than normal

Low house water supply pressure.

• The water pressure must be between 20 and 120 psi on models without a water filter and between 40 and 120 psi on models with a water filter. If the problem persists, it may be necessary to contact a plumber.

Reverse osmosis filtration system is used.

• Reverse osmosis filtration systems can reduce the water pressure below the minimum amount and result in icemaker issues. (Refer to the Connecting the Water Line section.)

Tubing connecting refrigerator to house supply valve is kinked.

• The tubing can kink when the refrigerator is moved during installation or cleaning resulting in reduced water flow. Straighten or repair the water supply line and arrange it to prevent future kinks.

Doors are opened often or for long periods of time.

• If the doors of the unit are opened often, ambient air will warm the refrigerator which will prevent the unit from maintaining the set temperature. Lowering the refrigerator temperature can help, as well as not opening the doors as frequently.

Doors are not closed completely.

• If the doors are not properly closed, ice production will be affected. See the “Doors will not close correctly or pop open” section in Parts & Features Troubleshooting for more information.

The temperature setting for the freezer is too warm.

• The recommended temperature for the freezer compartment for normal ice production is

0°F. If the freezer temperature is warmer, ice production will be affected.

TROUBLESHOOTING

43

Problem

Icemaker is not making ice

Possible Cause & Solution

Refrigerator was recently installed or icemaker recently connected.

• It may take up to 24 hours for each compartment to reach the desired temperature and for the icemaker to begin making ice.

Icemaker is not turned on.

• Locate the icemaker ON/OFF and confirm that it is turned on.

The ice detecting sensor is obstructed.

• Foreign substances or frost on the ice-detecting sensor can interrupt ice production. Make sure that the sensor area is clean at all times for proper operation.

The refrigerator is not connected to a water supply or the supply shutoff valve is not turned on.

• Connect the refrigerator to the water supply and turn the water shutoff valve fully open.

Icemaker shutoff (arm or sensor) obstructed .

• If your icemaker is equipped with an ice shutoff arm, make sure that the arm moves freely.

Ice has bad taste or odor.

Icemaker is making too much ice.

Reverse osmosis water filtration system is connected to your cold water supply.

• Reverse osmosis filtration systems can reduce the water pressure below the minimum amount and result in icemaker issues. (Refer to the Connecting the Water Line section).

Water supply contains minerals such as sulfur.

• A water filter may need to be installed to eliminate taste and odor problems. NOTE: In some cases, a filter may not help. It may not be possible to remove all minerals/odor/taste in all water supplies.

Icemaker was recently installed.

• Ice that has been stored for too long will shrink, become cloudy, and may develop a stale taste. Throw away old ice and make a new supply.

The food has not been stored properly in either compartment.

• Rewrap the food. Odors may migrate to the ice if food is not wrapped properly.

The interior of the refrigerator needs to be cleaned.

• See the Maintenance section for more information.

The ice storage bin needs to be cleaned.

• Empty and wash the bin (discard old cubes). Make sure that the bin is completely dry before reinstalling it.

Icemaker shutoff (arm/ sensor) is obstructed.

• Empty the ice bin. If your icemaker is equipped with an ice shutoff arm, make sure that the arm moves freely. Reinstall the ice bin and wait 24 hours to confirm proper operation.

44

TROUBLESHOOTING

Parts & Features

Doors will not close correctly or pop open.

Problem

Doors are difficult to open.

Refrigerator wobbles or seems unstable

Lights do not work.

Refrigerator has an unusual odor.

The interior of the refrigerator is covered with dust or soot.

Possible Cause & Solution

Food packages are blocking the door open.

• Rearrange food containers to clear the door and door shelves.

Ice bin, crisper cover, pans, shelves, door bins, or baskets are out of position.

• Push bins all the way in and put crisper cover, pans, shelves and baskets into their correct positions. See the Operation section for more information.

The doors were removed during product installation and not properly replaced.

• Remove and replace the doors according to the Removing and Replacing Refrigerator

Handles and Doors section.

Refrigerator is not leveled properly.

• See Door Alignment in the Refrigeration Installation section to level refrigerator.

The gaskets are dirty or sticky.

• Clean the gaskets and the surfaces that they touch. Rub a thin coat of appliance polish or kitchen wax on the gaskets after cleaning.

Door was recently closed.

• When you open the door, warmer air enters the refrigerator. As the warm air cools, it can create a vacuum. If the door is hard to open, wait one minute to allow the air pressure to equalize, then see if it opens more easily.

Leveling legs are not adjusted properly.

• Refer to the Leveling and Door Alignment section.

Floor is not level.

• It may be necessary to add shims under the leveling legs or rollers to complete installation.

LED interior lighting failure.

• The refrigerator compartment lamp is LED interior lighting, and service should be performed by a qualified technician.

The Air Filter may need to be set to the MAX setting or replaced.

• Set the Air Filter to the MAX setting. If the odor does not go away within 24 hours, the filter may need to be replaced. See the Replacing the Air Filter section for replacement instructions.

The refrigerator is located near a fire source, such as a fireplace, chimney, or candle.

• Make sure that the refrigerator is not located near a fire source, such as a fireplace, chimney or candle.

Noises

Problem

Clicking

Possible Cause & Solution

The defrost control will click when the automatic defrost cycle begins and ends. The thermostat control (or refrigerator control on some models) will also click when cycling on and off.

• Normal Operationchimney or candle.

TROUBLESHOOTING

45

Problem

Rattling

Whooshing

Gurgling

Popping

Sizzling

Vibrating

Dripping

Pulsating or highpitched sound

Possible Cause & Solution

Rattling noises may come from the flow of refrigerant, the water line on the back of the unit, or items stored on top of or around the refrigerator.

• Normal Operation

Refrigerator is not resting solidly on the floor.

• Floor is weak or uneven or leveling legs need to be adjusted. See the Leveling and Door

Alignment section.

Refrigerator with linear compressor was jarred while running.

• Normal Operation

Evaporator fan motor is circulating air through the refrigerator and freezer compartments.

• Normal Operation

Air is being forced over the condenser by the condenser fan.

• Normal Operation

Refrigerant flowing through the cooling system.

• Normal Operation

Contraction and expansion of the inside walls due to changes in temperature.

• Normal Operation

Water dripping on the defrost heater during a defrost cycle.

• Normal Operation

If the side or back of the refrigerator is touching a cabinet or wall, some of the normal vibrations may make an audible sound.

• To eliminate the noise, make sure that the sides and back cannot vibrate against any wall or cabinet.

Water running into the drain pan during the defrost cycle.

• Normal Operation

Your refrigerator is designed to run more efficiently to keep your food items at the desired temperature. The high efficiency compressor may cause your new refrigerator to run longer than your old one, but it is still more energy efficient than previous models. While the refrigerator is running, it is normal to hear a pulsating or high pitched sound.

• Normal Operation

46

LIMITED WARRANTY

LIMITED WARRANTY

For USA

TERMS AND CONDITIONS

ARBITRATION NOTICE: THIS LIMITED WARRANTY CONTAINS AN ARBITRATION PROVISION THAT

REQUIRES YOU AND LG TO RESOLVE DISPUTES BY BINDING ARBITRATION INSTEAD OF IN COURT,

UNLESS YOU CHOOSE TO OPT OUT. IN ARBITRATION, CLASS ACTIONS AND JURY TRIALS ARE NOT

PERMITTED. PLEASE SEE THE SECTION TITLED “PROCEDURE FOR RESOLVING DISPUTES” BELOW.

Should your LG Refrigerator (“Product”) fail due to a defect in materials or workmanship under normal and proper use, during the warranty period set forth below, LG Electronics (“LG”) will, at its option, repair or replace the Product. This limited warranty is valid only to the original retail purchaser of the Product and applies only when purchased and used within the United States including U.S. Territories.

Refrigerator/Freezer

One (1) year from the date of original retail purchase

Parts and Labor (internal/ functional parts only)

Sealed System

(Condenser, Dryer,

Connecting Tube and

Evaporator)

Five (5) years from the date of original retail purchase

Parts and Labor

WARRANTY PERIOD

Parts and Labor

Compressor

Five (5) years from the date of original retail purchase

Linear / Inverter

Compressor Only : Parts

Only for years 6-10 from the date of original retail purchase (Consumer will be charged for labor)

• Replacement products and parts are warranted for the remaining portion of the original warranty period or ninety (90) days, whichever is greater.

• Replacement products and parts may be new, reconditioned, refurbished, or otherwise factory remanufactured.

• Proof of original retail purchase specifying the Product model and date of purchase is required to obtain warranty service under this limited warranty.

EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THE PRODUCT IS LIMITED IN

DURATION TO THE DURATION OF THE ABOVE LIMITED WARRANTY. UNDER NO CIRCUMSTANCES

SHALL LG OR ITS U.S. DISTRIBUTORS/DEALERS BE LIABLE FOR ANY INDIRECT, INCIDENTAL,

CONSEQUENTIAL, SPECIAL, OR PUNITIVE DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST

GOODWILL, LOST REVENUES OR PROFITS, WORK STOPPAGE, IMPAIRMENT OF OTHER GOODS, COST

OF REMOVAL AND REINSTALLATION OF THE PRODUCT, LOSS OF USE, OR ANY OTHER DAMAGES

WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. LG’S TOTAL LIABILITY, IF ANY, SHALL NOT

EXCEED THE PURCHASE PRICE PAID BY YOU FOR THE PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This limited warranty gives you specific legal rights and you may also have other rights that vary from state to state.

THIS LIMITED WARRANTY DOES NOT COVER:

• Service trips to deliver, pick up, or install, educate how to operate, correct wiring, or correct unauthorized repairs.

• Damage or failure of the Product to perform during power failures and interrupted or inadequate electrical service.

LIMITED WARRANTY

47

• Damage or failure caused by leaky or broken water pipes, frozen water pipes, restricted drain lines, inadequate or interrupted water supply or inadequate supply of air.

• Damage resulting from operating the product in a corrosive atmosphere or contrary to the product owner’s manual.

• Damage or failure to the Product caused by accidents, pests and vermin, lightning, wind, fire, floods, acts of God, or any other causes beyond the control of LG.

• Damage or failure caused by unauthorized modification or alteration, or if used for other than the intended purpose.

• Damage or failure resulting from misuse, abuse, improper installation, repair, or maintenance.

Improper repair includes use of parts not authorized by LG. Improper installation or maintenance includes installation or maintenance contrary to the Product owner’s manual.

• Damage or failure caused by incorrect electrical current, voltage, or plumbing codes.

• Damage or failure caused by transportation and handling, including scratches, dents, chips, and/or other damage to the finish of the Product, unless such damage is reported within one (1) week of delivery.

• Damage or missing items to any display, open box, or discounted Product.

• Refurbished Product or any Product sold “As Is”, “Where Is”, “With all Faults”, or similar disclaimer.

• Products with original serial numbers that have been removed, altered, or cannot be readily determined.

• Increases in utility costs and additional utility expenses.

• Any noises associated with normal operation.

• Use of accessories (e.g., water filters, etc.), components, or consumable cleaning products that are not authorized by LG.

• Replacement of light bulbs, filters, or any consumable parts.

• When Product is used for other than normal and proper household use (e.g. commercial or industrial use, offices, and recreational facilities or vehicles) or contrary to the instructions outlined in the Product’s owner’s manual.

• Costs associated with removal and reinstallation of your Product for repairs.

• Shelves, door bins, drawers, handle and accessories, except for internal/functional parts covered under this limited warranty.

The cost of repair or replacement under these excluded circumstances shall be borne by the consumer.

TO OBTAIN WARRANTY SERVICE AND ADDITIONAL INFORMATION

Call 1-800-243-0000 and select the appropriate option from the menu.

Or visit our website at http://www.lg.com

Or by mail: LG Electronics Customer Service P.O. Box 240007 Huntsville, AL 35813 ATTN: CIC

PROCEDURE FOR RESOLVING DISPUTES:

ALL DISPUTES BETWEEN YOU AND LG ARISING OUT OF OR RELATING IN ANY WAY TO THIS LIMITED

WARRANTY OR THE PRODUCT SHALL BE RESOLVED EXCLUSIVELY THROUGH BINDING ARBITRATION, AND

NOT IN A COURT OF GENERAL JURISDICTION. BINDING ARBITRATION MEANS THAT YOU AND LG ARE EACH

WAIVING THE RIGHT TO A JURY TRIAL AND TO BRING OR PARTICIPATE IN A CLASS ACTION.

Definitions.

For the purposes of this section, references to “LG” mean LG Electronics U.S.A., Inc., its parents, subsidiaries and affiliates, and each of their officers, directors, employees, agents, beneficiaries, predecessors in interest, successors, assigns and suppliers; references to “dispute” or “claim” shall include any dispute, claim or controversy of any kind whatsoever (whether based in contract, tort, statute, regulation, ordinance, fraud, misrepresentation or any other legal or equitable theory) arising out of or relating in any way to the sale, condition or performance of the product or this Limited Warranty.

Notice of Dispute. In the event you intend to commence an arbitration proceeding, you must first notify

LG in writing at least 30 days in advance of initiating the arbitration by sending a letter to LG at LG

48

LIMITED WARRANTY

Electronics, USA, Inc. Attn: Legal Department- Arbitration 1000 Sylvan Ave, Englewood Cliffs 07632. You and LG agree to engage in good faith discussions in an attempt to amicably resolve your claim. The notice must provide your name, address, and telephone number; identify the product that is the subject of the claim; and describe the nature of the claim and the relief being sought. If you and LG are unable to resolve the dispute within 30 days, either party may proceed to file a claim for arbitration.

Agreement to Binding Arbitration and Class Action Waiver. Upon failure to resolve the dispute during the 30 day period after sending written notice to LG, you and LG agree to resolve any claims between us only by binding arbitration on an individual basis, unless you opt out as provided below. Any dispute between you and LG shall not be combined or consolidated with a dispute involving any other person’s or entity’s product or claim. More specifically, without limitation of the foregoing, any dispute between you and LG shall not under any circumstances proceed as part of a class or representative action. Instead of arbitration, either party may bring an individual action in small claims court, but that small claims court action may not be brought on a class or representative basis.

Arbitration Rules and Procedures.

To begin arbitration of a claim, either you or LG must make a written demand for arbitration. The arbitration will be administered by the American Arbitration Association

(“AAA”) and will be conducted before a single arbitrator under the AAA’s Consumer Arbitration Rules that are in effect at the time the arbitration is initiated (referred to as the “AAA Rules”) and under the procedures set forth in this section. The AAA Rules are available online at www.adr.org/consumer. Send a copy of your written demand for arbitration, as well as a copy of this provision, to the AAA in the manner described in the AAA Rules. You must also send a copy of your written demand to LG at LG Electronics,

USA, Inc. Attn: Legal Department- Arbitration 1000 Sylvan Avenue Englewood Cliffs, NJ 07632. If there is a conflict between the AAA Rules and the rules set forth in this section, the rules set forth in this section will govern. This arbitration provision is governed by the Federal Arbitration Act. Judgment may be entered on the arbitrator’s award in any court of competent jurisdiction. All issues are for the arbitrator to decide, except that issues relating to the scope and enforceability of the arbitration provision and to the arbitrability of the dispute are for the court to decide. The arbitrator is bound by the terms of this provision.

Governing Law.

The law of the state of your residence shall govern this Limited Warranty and any disputes between us except to the extent that such law is preempted by or inconsistent with applicable federal law.

Fees/Costs.

You do not need to pay any fee to begin an arbitration. Upon receipt of your written demand for arbitration, LG will promptly pay all arbitration filing fees to the AAA unless you seek more than $25,000 in damages, in which case the payment of these fees will be governed by the AAA Rules. Except as otherwise provided for herein, LG will pay all AAA filing, administration and arbitrator fees for any arbitration initiated in accordance with the AAA Rules and this arbitration provision. If you prevail in the arbitration, LG will pay your attorneys’ fees and expenses as long as they are reasonable, by considering factors including, but not limited to, the purchase amount and claim amount. Notwithstanding the foregoing, if applicable law allows for an award of reasonable attorneys’ fees and expenses, an arbitrator can award them to the same extent that a court would. If the arbitrator finds either the substance of your claim or the relief sought in the demand is frivolous or brought for an improper purpose (as measured by the standards set forth in Federal Rule of Civil Procedure 11(b)), then the payment of all arbitration fees will be governed by the AAA Rules. In such a situation, you agree to reimburse LG for all monies previously disbursed by it that are otherwise your obligation to pay under the AAA Rules. Except as otherwise provided for, LG waives any rights it may have to seek attorneys’ fees and expenses from you if LG prevails in the arbitration.

Hearings and Location.

If your claim is for $25,000 or less, you may choose to have the arbitration conducted solely on the basis of (1) documents submitted to the arbitrator, (2) through a telephonic hearing, or (3) by an in-person hearing as established by the AAA Rules. If your claim exceeds $25,000, the right to a hearing will be determined by the AAA Rules. Any in-person arbitration hearings will be held at a location within the federal judicial district in which you reside unless we both agree to another location or we agree to a telephonic arbitration.

Opt Out.

You may opt out of this dispute resolution procedure. If you opt out, neither you nor LG can require the other to participate in an arbitration proceeding. To opt out, you must send notice to LG no later than 30 calendar days from the date of the first consumer purchaser’s purchase of the product by either: (i) sending an e-mail to [email protected], with the subject line: “Arbitration Opt Out” or (ii) calling 1-

800-980-2973. You must include in the opt out e-mail or provide by telephone: (a) your name and address;

(b) the date on which the product was purchased; (c) the product model name or model number; and (d)

LIMITED WARRANTY

49

the serial number (the serial number can be found (i) on the product; or (ii) online by accessing https:// www.lg.com/us/support/repair-service/schedule-repair continued and clicking on “Find My Model & Serial

Number”).

You may only opt out of the dispute resolution procedure in the manner described above (that is, by e-mail or telephone); no other form of notice will be effective to opt out of this dispute resolution procedure.

Opting out of this dispute resolution procedure will not affect the coverage of the Limited Warranty in any way, and you will continue to enjoy the full benefits of the Limited Warranty. If you keep this product and do not opt out, then you accept all terms and conditions of the arbitration provision described above.

50

LIMITED WARRANTY

For Canada

TERMS AND CONDITIONS

ARBITRATION NOTICE: THIS LIMITED WARRANTY CONTAINS AN ARBITRATION PROVISION THAT

REQUIRES YOU AND LG TO RESOLVE DISPUTES BY BINDING ARBITRATION INSTEAD OF IN COURT,

UNLESS THE LAWS OF YOUR PROVINCE OR TERRITORY DO NOT PERMIT THAT, OR, IN OTHER

JURISDICTIONS, IF YOU CHOOSE TO OPT OUT. IN ARBITRATION, CLASS ACTIONS AND JURY TRIALS

ARE NOT PERMITTED. PLEASE SEE THE SECTION TITLED “PROCEDURE FOR RESOLVING DISPUTES”

BELOW.

Should your LG Refrigerator (“Product”) fail due to a defect in materials or workmanship under normal and proper use, during the warranty period set forth below, LG Electronics Canada, Inc. (“LGECI”) will, at its option, repair or replace the Product upon receipt of proof of the original retail purchase. This limited warranty is valid only to the original retail purchaser of the Product and applies only to a Product distributed, purchased and used within Canada, as determined at the sole discretion of LGECI.

WARRANTY PERIOD (Note: If the original date of purchase cannot be verified, the warranty will begin sixty (60) days from the date of manufacture)

Refrigerator

One (1) year from the date of original retail purchase

Sealed System (Condenser, Dryer, Connecting

Tube and Evaporator)

One (1) year from the date of original retail purchase

Seven (7) years from the date of original retail purchase

Linear / Inverter

Compressorg

Ten (10) years from the date of original retail purchase

Parts and Labor (internal/ functional parts only)

Parts and Labor Parts only (Consumer will be charged for labor)

Part only (Consumer will be charged for labor)

• Replacement products and parts are warranted for the remaining portion of the original warranty period or ninety (90) days, whichever is greater.

• Replacement products and parts may be new, reconditioned, refurbished, or otherwise factory remanufactured, all at the sole discretion of LGECI.

• Proof of original retail purchase specifying the Product model and date of purchase is required to obtain warranty service under this Limited Warranty.

LGECI’S SOLE LIABILITY IS LIMITED TO THE LIMITED WARRANTY SET OUT ABOVE. EXCEPT AS

EXPRESSLY PROVIDED ABOVE, LGECI MAKES NO, AND HEREBY DISCLAIMS, ALL OTHER WARRANTIES

AND CONDITIONS RESPECTING THE PRODUCT, WHETHER EXPRESS OR IMPLIED, INCLUDING BUT

NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE, AND NO REPRESENTATIONS SHALL BE BINDING ON LGECI. LGECI

DOES NOT AUTHORIZE ANY PERSON TO CREATE OR ASSUME FOR IT ANY OTHER WARRANTY OBLI-

GATION OR LIABILITY IN CONNECTION WITH THE PRODUCT. TO THE EXTENT THAT ANY WARRANTY

OR CONDITION IS IMPLIED BY LAW, IT IS LIMITED TO THE WARRANTY PERIOD SET OUT ABOVE. UN-

DER NO CIRCUMSTANCES SHALL LGECI, THE MANUFACTURER OR DISTRIBUTOR OF THE PRODUCT,

BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, DIRECT, INDIRECT, PUNITIVE OR

EXEMPLARY DAMAGES, INCLUDING, WITHOUT LIMITATION, LOSS OF GOODWILL, LOST PROFITS,

LOSS OF ANTICIPATED PROFITS, LOST REVENUE, LOSS OF USE, OR ANY OTHER DAMAGE, WHETHER

ARISING DIRECTLY OR INDIRECTLY FROM ANY CONTRACTUAL BREACH, FUNDAMENTAL BREACH,

TORT OR OTHERWISE, OR FROM ANY ACTS OR OMISSIONS. LGECI’S TOTAL LIABILITY, IF ANY, SHALL

NOT EXCEED THE PURCHASE PRICE PAID BY YOU FOR THE PRODUCT.

This Limited Warranty gives you specific legal rights. You may also have other rights that vary from province to province depending on applicable provincial laws. Any term of this Limited Warranty that negates or varies any implied condition or warranty under provincial law is severable where it conflicts with such provincial law without affecting the remainder of this warranty’s terms.

LIMITED WARRANTY

51

THIS LIMITED WARRANTY DOES NOT COVER:

• Service trips to i) deliver, pick up, or install or; educate on how to operate the Product; ii) correct wiring or plumbing; or iii) correct unauthorized repairs or installations of the Product;

• Damage or failure of the Product to perform during power failures and interrupted or inadequate electrical service;

• Damage or failure caused by leaky or broken water pipes, frozen water pipes, restricted drain lines, inadequate or interrupted water supply or inadequate supply of air;

• Damage or failure resulting from operating the Product in a corrosive atmosphere or contrary to the instructions outlined in the Product’s owner’s manual;

• Damage or failure to the Product caused by accidents, pests and vermin, lightning, wind, fire, floods, acts of God, or any other causes beyond the control of LGECI or the manufacturer;

• Damage or failure resulting from misuse, abuse, improper installation, repair, or maintenance of the

Product. Improper repair includes use of parts not authorized or specified by LGECI. Improper installation or maintenance includes installation or maintenance contrary to the Product’s owner’s manual;.

• Damage or failure caused by unauthorized modification or alteration of the Product, or if used for other than the intended household purpose/use of the Product, or damage or failure resulting from any water leakage due to improper installation of the Product;

• Damage or failure caused by incorrect electrical current, voltage or plumbing codes;

• Damage or failure caused by use that is other than normal household use, including, without limitation, commercial or industrial use, including use in commercial offices or recreational facilities, or as otherwise outlined in the Product’s owner’s manual;

• Damage or failure caused by the use of any accessories, components or cleaning products, including, without limitation, water filters, that are not approved/authorized by LGECI;

• Replacement of the water filter cartridge due to water pressure that is outside the specified operating range or due to excessive sediment in the water supply;

• Damage or failure caused by transportation and handling, including scratches, dents, chips and/or other damage to the finish of the Product, unless such damage results from defects in materials or workmanship and is reported to LGECI within one (1) week of delivery of the Products;

• Damage or missing items to any display, open box, refurbished or discounted Product;

• Refurbished Product or any Product sold “As Is”, “Where Is”, “With all Faults”, or any similar disclaimer;

• Products with original serial numbers that have been removed, altered or cannot be readily determined at the discretion of LGECI;

• Increases in utility costs and additional utility expenses in any way associated with the Product;

• Any noises associated with normal operation of the Product;

• Replacement of light bulbs, filters, fuses or any other consumable parts;

• Replacement of any part that was not originally included with the Product;

• Costs associated with removal and/or reinstallation of the Product for repairs; and

• Shelves, door bins, drawers, handle and accessories to the Product, except for internal/functional parts covered under this Limited Warranty.

• Coverage for “in Home” repairs, for products in-warranty, will be provided if the Product is within a 150 km radius from the nearest authorized service center (ASC), as determined by LG Canada. If your Product is located outside a 150 km radius from a ASC, as determined by LG Canada, it will be your responsibility to bring the Product, at your sole expense, to the ASC for in-warranty repair.

All costs and expenses associated with the above excluded circumstances, listed under the heading,

This Limited Warranty Does Not Cover, shall be borne by the consumer.

TO OBTAIN WARRANTY SERVICE AND ADDITIONAL INFORMATION, PLEASE CALL OR VISIT OUR WEBSITE:

Call 1-888-542-2623 (7 A.M. to 12 A.M., 365 days a year) and select the appropriate option from the menu, or visit our website at http://www.lg.com

52

LIMITED WARRANTY

PROCEDURE FOR RESOLVING DISPUTES:

EXCEPT WHERE PROHIBITED AT LAW, ALL DISPUTES BETWEEN YOU AND LG ARISING OUT OF OR RELATING

IN ANY WAY TO THIS LIMITED WARRANTY OR THE PRODUCT SHALL BE RESOLVED EXCLUSIVELY THROUGH

BINDING ARBITRATION, AND NOT IN A COURT OF GENERAL JURISDICTION. EXCEPT WHERE PROHIBITED

AT LAW, YOU AND LG BOTH IRREVOCABLY AGREE TO WAIVE THE RIGHT TO A JURY TRIAL AND TO BRING

OR PARTICIPATE IN A CLASS ACTION.

Definitions. For the purposes of this section, references to “LG” mean LG Electronics Canada, Inc., its parents, subsidiaries and affiliates, and each of their officers, directors, employees, agents, beneficiaries, predecessors in interest, successors, assigns and suppliers; references to “dispute” or “claim” shall include any dispute, claim or controversy of any kind whatsoever (whether based in contract, tort, statute, regulation, ordinance, fraud, misrepresentation or any other legal or equitable theory) arising out of or relating in any way to the sale, condition or performance of the product or this Limited Warranty.

Notice of Dispute.

In the event you intend to commence an arbitration proceeding, you must first notify

LG in writing at least 30 days in advance of initiating the arbitration by sending a letter to LGECI Legal

Team at 20 Norelco Drive, North York, Ontario, Canada M9L 2X6 (the “Notice of Dispute”). You and LG agree to engage in good faith discussions in an attempt to amicably resolve your claim. The notice must provide your name, address, and telephone number; identify the product that is the subject of the claim; and describe the nature of the claim and the relief being sought. If you and LG are unable to resolve the dispute within 30 days of LG’s receipt of the Notice of Dispute, the dispute shall be resolved by binding arbitration in accordance with the procedure set out herein. You and LG both agree that, during the arbitration proceeding, the terms (including any amount) of any settlement offer made by either you or LG will not be disclosed to the arbitrator until the arbitrator determines the dispute.

Agreement to Binding Arbitration and Class Action Waiver. Upon failure to resolve the dispute during the 30 day period after LG’s receipt of the Notice of Dispute, you and LG agree to resolve any claims between you and LG only by binding arbitration on an individual basis, unless you opt out as provided below, or you reside in a jurisdiction that prevents full application of this clause in the circumstances of the claims at issue (in which case if you are a consumer, this clause will only apply if you expressly agree to the arbitration). To the extent permitted by applicable law, any dispute between you and LG shall not be combined or consolidated with a dispute involving any other person’s or entity’s product or claim. More specifically, without limitation of the foregoing, except to the extent such a prohibition is not permitted at law, any dispute between you and LG shall not under any circumstances proceed as part of a class or representative action. Instead of arbitration, either party may bring an individual action in small claims court, but that small claims court action may not be brought on a class or representative basis except to the extent this prohibition is not permitted at law in your province or territory of jurisdiction as it relates to the claims at issue between you and LG.

Arbitration Rules and Procedures.

To begin arbitration of a claim, either you or LG must make a written demand for arbitration. The arbitration will be private and confidential, and conducted on a simplified and expedited basis before a single arbitrator chosen by the parties under the provincial or territorial commercial arbitration law and rules of the province or territory of your residence. You must also send a copy of your written demand to LG at LG Electronics, Canada, Inc., Attn: Legal Department- Arbitration, 20

Norelco Drive, North York, Ontario M9L 2X6. This arbitration provision is governed by your appli cable provincial or territorial commercial arbitration legislation. Judgment may be entered on the arbitrator’s award in any court of competent jurisdiction. All issues are for the arbitrator to decide, except that, issues relating to the scope and enforceability of the arbitration provision and to the arbitrability of the dispute are for the court to decide. The arbitrator is bound by the terms of this provision.

Governing Law. The law of the province or territory of your purchase shall govern this Limited Warranty and any disputes between you and LG except to the extent that such law is preempted by or inconsistent with applicable federal or provincial/territorial law. Should arbitration not be permitted for any claim, action, dispute or controversy between you and LG, you and LG attorn to the exclusive jurisdiction of the courts of the province or territory of your purchase for the resolution of the claim, action, dispute or controversy between you and LG.

Fees/Costs.

You do not need to pay any fee to begin an arbitration. Upon receipt of your written demand for arbitration, LG will promptly pay all arbitration filing fees unless you seek more than $25,000 in damages, in which case the payment of these fees will be governed by the applicable arbitration rules.

Except as otherwise provided for herein, LG will pay all filing, administration and arbitrator fees for any arbitration initiated in accordance with the applicable arbitration rules and this arbitration provision. If you prevail in the arbitration, LG will pay your attorneys’ fees and expenses as long as they are reasonable, by

LIMITED WARRANTY

53

considering factors including, but not limited to, the purchase amount and claim amount. Notwithstanding the foregoing, if applicable law allows for an award of reasonable attorneys’ fees and expenses, an arbitrator can award them to the same extent that a court would. If the arbitrator finds either the substance of your claim or the relief sought in the demand is frivolous or brought for an improper purpose

(as measured by the applicable laws), then the payment of all arbitration fees will be governed by the applicable arbitration rules. In such a situation, you agree to reimburse LG for all monies previously disbursed by it that are otherwise your obligation to pay under the applicable arbitration rules. Except as otherwise provided for, LG waives any rights it may have to seek attorneys’ fees and expenses from you if

LG prevails in the arbitration.

Hearings and Location.

If your claim is for $25,000 or less, you may choose to have the arbitration conducted solely (1) on the basis of documents submitted to the arbitrator, (2) through a telephonic hearing, or (3) by an in-person hearing as established by the applicable arbitration rules. If your claim exceeds $25,000, the right to a hearing will be determined by the applicable arbitration rules. Any inperson arbitration hearings will be held at the nearest, most mutually-convenient arbitration location available within the province or territory in which you reside unless you and LG both agree to another location or agree to a telephonic arbitration.

Severability and Waiver.

If any portion of this Limited Warranty (including these arbitration procedures) is unenforceable, the remaining provisions will continue in full force and effect to the maximum extent permitted by applicable law. Should LG fail to enforce strict performance of any provision of this Limited

Warranty (including these arbitration procedures), it does not mean that LG intends to waive or has waived any provision or part of this Limited Warranty.

Opt Out.You may opt out of this dispute resolution procedure. If you opt out, neither you nor LG can require the other to participate in an arbitration proceeding. To opt out, you must send notice to LG no later than 30 calendar days from the date of the first consumer purchaser’s purchase of the product by either (i) sending an e-mail to [email protected], with the subject line: “Arbitration Opt Out;” or (ii) calling 1-

800-980-2973. You must include in the opt out e-mail or provide by telephone: (a) your name and address;

(b) the date on which the product was purchased; (c) the product model name or model number; and (d) the serial number (the serial number can be found (i) on the product; or (ii) online by accessing https:// www.lg.com/ca_en/support/repair-service/schedule- repair and clicking on “Find My Model & Serial

Number”).

In the event that you “Opt Out”, the law of the province or territory of your residence shall govern this

Limited Warranty and any disputes between you and LG except to the extent that such law is preempted by or inconsistent with applicable federal or provincial/territorial law. Should arbitration not be permitted for any claim, action, dispute or controversy between you and LG, you and LG agree to attorn to the exclusive jurisdiction of the courts of the province or territory of your residence for the resolution of the claim, action, dispute or controversy between you and LG.

You may only opt out of the dispute resolution procedure in the manner described above (that is, by e-mail or telephone); no other form of notice will be effective to opt out of this dispute resolution procedure.

Opting out of this dispute resolution procedure will not affect the coverage of the Limited Warranty in any way, and you will continue to enjoy the full benefits of the Limited Warranty. If you keep this product and do not opt out, then you accept all terms and conditions of the arbitration provision described above.

Conflict of Terms.

In the event of a conflict or inconsistency between the terms of this Limited Warranty and the End User License Agreement (“EULA”) in regards to dispute resolution, the terms of this Limited

Warranty shall control and govern the rights and obligations of the parties and shall take precedence over the EULA.

54

Memo

Memo

55

LG Customer Information Center

For inquiries or comments, visit www.lg.com

or call:

1-800-243-0000

U.S.A.

1-888-542-2623

CANADA

Register your product Online!

www.lg.com