VKS-SG Attachment System

For three decades Bredent has been offering innovative products for dental laboratories. With a current workforce of more than 200 qualified employees at the company headquarters in Senden/Iller, Germany, Bredent develops and produces over 8000 high quality products which help dentists and dental laboratories to optimize work processes and to reduce costs. 96% of all Bredent products are based on ideas from working dental technicians and are produced in-house for the strictest quality control.

Bredent holds ISO 9001 / DIN EN 46001 certification, keeping in step with the most modern high-tech manufacturing.

“Thank you very much for your confi dence in Bredent

employees and technologies”

“We are constantly striving to improve!”

Peter Brehm ~ CEO

Bredent

“It is important to us to provide quality products and technical service”

Peter Kuch, CDT, ZTM ~ CEO

Ellen Kuch ~ President

XPdent Corporation

The sole importer of Bredent products for more than 14 years

Located in sunny Miami, Florida, XPdent is the sole importer of Bredent, Wiedent, and ZEO CE LIGHT Porcelain products into the United States.

XPdent’s goal is to share with the US technicians some of the best European products available. XPdent was founded by Peter Kuch, a certified dental technician with vast knowledge in dental implants and attachments, who now heads the technical support staff.

XPdent’s standards of quality products and quality service also include quality education with the addition of our state of the art training laboratory for hands on training in attachments, waxing, milling and implants.

For more information about the courses, call 1.877.328.3965 and ask your account representative about course schedules and pricing. All courses are good for continuing education credits.

Contents

53.....

30.....

14.....

54.....

44.....

43.....

55.....

48.....

18.....

25.....

21.....

31.....

34.....

36.....

40.....

51.....

46.....

54.....

60.....

ATTACHMENTS

VKS-SG Attachments

VKS-SG/OC Bond-In Exchangeable Stud

VKS-SG Exchangeable Stud

Drill-N-Tap Retrievable Ball Screw Kit

VKS-OC Attachments

VKS-OC Exchangeable Stud

VKS-OC RS Abutments

Occlusal Screw System

VKS Stud Reworking Set

VS-3 Mini & SV Attachments

NEW! VS-3 Mini Tapered

VSP Bar Attachments

VSS Vario Soft Bar

Diatit Multidrill System

Security Lock

Locking Pin Snap

NEW! Friction Splint FS1

Interlock

FGP Friction Fit System

6......

7......

BRUSHES

NEW!

Kolinsky Brushes

NEW!

Magic Contrast Brushes

110...

117...

111...

51.....

117...

112...

64.....

116...

116...

114...

93.....

64.....

115...

59.....

51.....

65.....

65.....

91.....

115...

64.....

116...

114...

102...

LIQUIDS

Chrome Cobalt Bonding

Colloidal Graphite

Diephos UV Die Spacer

Exakto-Form

FGP Insulating Agent

Gloss & Hardening Agent for Plasters

Isobre Wax Insulating Liquid

Isoflex Ceramic Insulating Liquid

Light-Curing Die Spacer

Master-Sep Insulating Liquid

Microceramic

Milling/Drilling Oil

Oxide-Stop

Pi-Ku-Plast

Plaster Separating Liquid

Plaster Solvent

Porcelain Mixing Liquid

Ropak Liquid

Seracoll UV Light-Curing

Silicone & Wax Surface Tension

Reducing Agent

Stain Liquid

Tooth-colored UV Opaquer

Wax-Lite Surface Tension Reducing Agent

72.....

118...

127...

12.....

89.....

EQUIPMENT

NEW! Milling Machine BF-2

Silano Pen

NEW! Bre.Lux Power Unit

NEW! Bredent Casting Technique

NEW!

Waxpool Duo

120...

111...

120...

65.....

MATERIALS

Heat Absorbent Paste

Microceramic

Retention Beads & Crystals

Transblock

59.....

62.....

62.....

63-64

63.....

MODELS & DUPLICATING

Exakto-Form Resin

Exaktosil C Kneading Silicone

Exaktosil N 21 Duplicating Silicone

Master-Pin System

Multisil-Mask Soft

59.....

112...

93.....

93.....

51.....

RESINS

Exakto-Form Resin

Pi-Ku-Plast HP 36

NEW! Seracoll UV

NEW! CompoForm UV

NEW! DTK Adhesive Kit

84.....

88.....

86.....

87.....

78.....

84.....

88.....

89.....

91.....

85.....

12.....

86.....

85.....

66.....

87.....

90.....

TOOLS

Aesthetic Gnathoflex

Articulation Paper Holder

NEW! Bredent Casting Technique

NEW! Ceramix

Cervical Disc

Diatit Cutting Tools

NEW! Ergonomic Wax Knife

Gnathoflex Premium

Mamelon Cutter

NEW! Quick Change

NEW! Quick Tool

NEW! Repositioning Tweezers

Set-up Grinding Tool

Spot Clip

NEW! Thermo-pen

NEW! Transfuser

90.....

94.....

95.....

95.....

108...

94.....

95.....

94.....

91.....

101...

98.....

12.....

95.....

96.....

97.....

95.....

95.....

97.....

WAXES

Aesthetic Gnathoflex

Biotec Milling Wax

Biotec Wax System

Bredent Casting Technique

Cervical Wax

Dipping Waxes

Elaflex

Gnathoflex Premium

K2 Exact Carving Wax

KBI Wax

Outer Copings Wax

Posifix

Specialty Waxes

Splendido Wax

Standard Modelling Wax

Sticky Wax

Undercut Wax

Visio Dip

103...

104...

105...

106...

107...

108...

108...

109...

PONTICS

Biotec Pontic Blocks

Between Blocks BW-BL

In Between Pontics BWG

Hollow Pontic Blocks HP-BL

Shallow Collar Pontics FGMK-BL

AK-BL Pontics

Posifix

Aesthetic and Ergonomic AEMK-BL

71.....

78.....

80.....

66.....

55.....

70.....

82.....

74.....

78.....

83.....

79.....

83.....

BURS & DISCS

Diabolo Sintered Diamonds

Diacryl Diamond for Acrylic

Diagen

Diatit Cutting Tools

Diatit Multidrill System

Diatit and TungstenCarbide Burs

Giflex-TR Diamond Discs

Milling Bur System

Set-up Grinding Tool

Silicone Burs

Special Diamonds for Veneering

Transflex Diamond Discs

122...

125...

122...

124...

121...

81.....

POLISHINGS

Abraso Buff

Abraso Fix

Abraso Soft

Polishing Pastes

Polishing Assortment Kits

Silicone + Rubber Polishing

(Abraso-Gum)

4

New Br

NEW!

Koli Brush

- golden brown natural hair

Natural hair brushes made of superior quality Kolinsky hair.

ushes!

spheres for easier porcelain build-ups. Fine and stable tip made of carefully selected hair.

The shape and quality of the hair makes for perfect retention of moisture and improved adhesion & application of ceramic material.

The desired elasticity is obtained by the unique design and combination.

This way the applied ceramic layers will not be damaged.

NEW!

Magic Contrast

- black hair

Fatigue-free working thanks to the contrast of the ceramic material and the brush hair. The synthetic hairs provide lasting resiliency of the brush tip.

The pointed shape of a dry brush hair is immediately restored by wetting, tapping off or vibrating the brush lightly.

Thanks to the strong contrast, any contamination such as dust or dry ceramic particles can be clearly recognized.

Go from a spatula shaped tip to a pointed tip by wetting the brush, tapping or vibrating it slightly with a suitable instrument.

High elasticity to pick up specific quantities of ceramic material more easily.

The optimized resiliency restores the shape of the brush tip immediately after picking up the porcelain. The contrast between the ceramic material and black brush hairs promotes clear visibility of the amount to be applied.

The spatula shape can be easily achieved after pressing the tip with two fingers. This way, the brush can be shaped individually.

Large quantities of ceramic material are picked up and time-saving layering is achieved thanks to the elasticity and the springiness of the brush hair.

The spatula shape does not reduce the stability of the brush hair; hence, less time is required for applying the ceramic material to the framework.

5

NEW!

Koli Brush

- product line

Scale 1:1

Product Name

KoliBrush

KoliBrush

KoliBrush

KoliBrush

KoliBrush

KoliBrush

KoliBigBrush

KoliBrush

KoliOpaquerBrush

Size

4, 6, 8 B

1

2

4

6

8

8 BigBrush

1/0

5

Qty.

1 piece each

2 pieces

2 pieces

2 pieces

1 piece

1 piece

1 piece

2 pieces

2 pieces

Item #

390 KSET 1

390 K001 0

390 K002 0

390 K004 0

390 K006 0

390 K008 0

390 K008 B

390 KS01 0

390 KS03 0

Koli Brush Set

#S390 KSET 1

Kit includes:

1, 2, 4, 5, 6, 8 & 1/0 sizes

$99.00

Price

$86.00

$20.00

$21.95

$28.95

$19.50

$23.50

$60.50

$25.50

$32.95

6

Carefully Selected Hair!

NEW!

Magic Contrast

- product line

Scale 1:1

Product Name Size

MagicContrast

MagicContrast

MagicContrast

4, 6, 8

1

2

MagicContrast

MagicContrast

MagicContrast

MagicContrastBigBrush

MagicContrast

MagicContrast-Opaquer

4

6

8

8 BigBrush

1/0

5

Qty.

1 piece each

2 pieces

2 pieces

2 pieces

1 piece

1 piece

1 piece

2 pieces

2 pieces

Item #

390 CSET 1

390 C001 0

390 C002 0

390 C004 0

390 C006 0

390 C008 0

390 C008 B

390 CS01 0

390 CS03 0

Magic Contrast Set

#S390 CSET 1

Kit includes:

1, 2, 4, 5, 6, 8 & 1/0 sizes

$148.00

Price

$80.00

$37.50

$38.50

$42.50

$31.95

$37.50

$60.00

$37.50

$42.50

Lasting Resiliency of the Brush Tip!

7

BREDENT CASE DESIGN IDEAS

4 Implant Overdenture: Notice the angulation of the implants from each other. The VKS-OC RS

Implant Abutment system allows each implant to have a 15° deviation from the path of insertion

(up to 30° from each other).

The OC-RS Implant Abutments are screwed directly into the implants and are available in

3 diameters, each with 3 tissue heights. This picture shows the females engaged into the overcasting.

Although an overcasting is recommended, the females can be placed in individual metal housings and embedded into the acrylic. Having the females in a housing or overcasting allows the clips to be replaced easily without curing.

8

The bar design above illustrates the low profile of the VSP bar attachment. The VSP bar is a parallel bar that can be used in any standard bar mandrel. The VSP clips do not fold over and last for a long period of time. Replacing the clips are a snap with the insertion pin.

This case shows the 1.7 SG attachment on the side of an implant coping. Although telescopic copings were milled, the attachments give added retention and versatility. Either a denture or a porcelain-metal bridge can be fabricated over the copings.

In combination cases (Implant - Natural Dentition), the attachments can be placed anywhere sufficient space is available.

A combination of SG and OC-RS implant abutments in this case is used to restore a lower arch. When casting yellow gold copings such as the one above, a Type IV alloy is highly recommended.

The Low Profile

Application of the

Due to tight inter-occlusal space, the attachments were placed mesially and distally instead of on top of the gold copings. The copings were splinted for added strength and support.

Bredent Attachments aids in the stability of your implant case

Production sequence for an implant bar case

1. 6 unit implant case requiring an implant bar.

2. Waxing sleeves are used and customized with resin.

3. The implant frame is waxed up using the

SG bar patrix.

4. The bar is cast in a type 4 alloy, at least

230 vicker hardness.

5. To create the partial, the yellow females are snapped onto the attachments parallel to each other.

6. All undercuts in the case are blocked out, including under the attachments.

7. A silicone mold is formed for duplication.

8. The refractory model is poured in investment material.

9. The overcasting is waxed onto the refractory model.

10. The overcasting is cast and deplated.

11. The attachment housings are automatically created as part of the overframe.

12. Ropak light curing opaquer is applied to the casting.

13. The case is finished using standard techniques.

14. The finished case in the mouth.

15. For more detailed instructions, please call our technical support department.

9

Bredent Attachments Requirements for Success:

The following are a list of things needed in order to produce a successful, long-lasting prosthesis using Bredent attachments:

1. All attachments are to be installed parallel.

*

** **

2. Attachments are to be cast using an alloy with a vickers hardness of at least 230.

3. A metal housing is required for all Bredent attachments.

4. All Bredent attachments used for combination fixed/removable cases are to have a milled lingual shelf with an interlocking groove in the mesio-interproximal that will accommodate a lingual arm*. This prevents distal displacement of the prosthesis, centers occlusal forces down the long axis of the tooth and keeps the attachment stress-free. Optional: For cases where a lingual shelf and arm are not desired, then, any SV** styled attachment (stress distributor) may be used. The unique design of these attachments eliminates the need for lingual shelves and arms.

5. Educate the patient to insert the prosthesis with finger pressure and not to bite the prosthesis into place.

6. It is recommended that the patients clean their prosthesis at least twice daily to prevent impaction of plaque into the plastic matrix which can cause premature wear of the attachments.

7. Regularly scheduled visits to the dentist (at least every six months) by the patient are recommended to check the prosthesis to maintain and assure accuracy of fit. Improper fitting dentures and partials will compromise the longevity of the attachment. When needed, relining of the acrylic base is strongly recommended.

8. Avoid over-polishing, grinding or adjusting to preserve longer lasting retention of the Bredent attachment.

Yellow-Extrafine Round Brushes Highly Recommended!

Fine abrasive particles integrated into the bristles enable all dental materials to be pre-polished without using polishing paste.

Abraso-Fix Polishers are suitable to pre-polish attachment components without the risk of over reducing material!

(For more information about Abraso-Fix please go to page 125)

10

If you have any questions on any Bredent attachment case, please contact our technical support team for assistance at:

1.877.329.3965

Bredent USA FREE Case Designer

1

> Requires a web browser with Macromedia Flash 5.0 or later installed.

Use any of the Bredent attachments to digitally construct a case.

The case Designer is a simple program that allows the user to design cases by placing natural teeth, crowns, root caps and implants onto a blank upper and/or lower arch. It further enables the user to combine these restorative components with a variety of Bredent attachments and other frequently used techniques such as lingual arms or interlocks. Using the Universal Tooth Numbering

Code, the upper and lower arches are numbered 1-32. The user can select or erase each individual tooth or entire arches.

A combination of natural teeth and implant supported restorations can be easily drawn and displayed simply by clicking on an attachment component icon and adding it to the corresponding oral structure.

Design • Combine • Decide

3

2 4

11

NEW!

Bredent Casting Technique Book

“A dental technician’s manual for producing precise fi tting, homogenous and biocompatible dental castings”

Bredent Casting Technique

#992 961 GB

$150.00

Spanish Version

#992 961 0E

$150.00

The Bredent Casting Technique

(According to Sabath) is an instructional user manual with simplifi ed, reliable scientifi c data and experience in the dental casting process. The main purpose of the book is to provide practical knowledge for the dental technician rather than scientifi c or metallurgical formulas and processes. It is a 230 page book assembled in a loose-leaf, hard-backed, ring binder style with 6 chapters categorized in the following manner:

Chapter 1: Investment Compounds - composition of investments and application ranges, processing information, wax movement and thermal wax tension, pressure investing, comparison of ring fl asks systems and investing.

Chapter 2: Preheating (Burn-Out) - Linear preheating, Kiln types and their effects on investment ring molds, rapid fi re-preheating techniques and practice-related case studies about preheating and castings fi t results.

Chapter 3: Casting - Materials, alloy melting (fl ame, induction, resistance, electric arc), comparison of casting methods and their results.

Chapter 4: Cast - Port supply (Sprueing) - Direct and indirect sprueing techniques and infl ow of metal.

Chapter 5: Bredent Casting Technique According to Sabath.

Chapter 6: Refractory model casting techniques - Choosing proper sprues and attaching pressure equalization channels.

Sprues for Centrifugal Casting & Rinsing Heads

Sprues for Centrifugal

Casting

Sprue Channel

Ø mm

2.5

Head

Ø mm

4.5

2.5

5.0

3.0

6.0

6.5

Assortment

390 pieces

Centrifugal casting, containing

30 sprues and 30 rinsing heads each

#430 014 80 $335.00

Rinsing Heads

3.5

2.5

2.5

3.0

Double Rinsing Heads

2.5

3.0

12

4.0

5.0

6.0

5.0

5.0

-

-

-

-

-

3.5

4.0

Sprue

Ø mm

3.0

3.5

50

50

50

50

50

50

150

50

150

Pack

pieces

50

150

50

150

Item #

430 014 41

430 014 77

430 014 42

430 014 78

430 014 43

430 014 79

430 014 44

430 014 81

$45.50

$130.00

$45.50

$130.00

$45.50

$130.00

$45.50

$130.00

430 014 48

430 014 49

430 014 51

$45.50

$45.50

$45.50

430 014 56

430 014 58

$45.50

$45.50

Highly Recommended Requires Modifi cation

Attachment Selector by Indication

Attachments

Mesial/Distal of Implant Bars On Side of Implant Bars For Implant Abutments Direct Ball Implant Abutments

VS-3 Mini

VS-3 Mini / SV

VKS-SG Patrix

VKS-SG / SV

VKS-SG Bar Patrix

Exchangeable SG

Exchangeable SG

Titanium Bar

Drill-N-Tap

VKS-OC

Exchangeable OC

VKS Universal

VKS-OC RS Titanium

Implant Abutments

VSP-FS / GS Bar

VSP-FS/GS Titanium

Bar

VSS Bar

Locking Pin

Security Lock

Occlusal Screw

System

Diatit Tool Set

Friction Splint FS1

VS-3 Conical Bridges

(See Attachment Dimensions on pages 56-58)

13

VS-3 Mini

> The most widely used attachment in Europe!

> VS-3 Mini offers a gentle slide-in friction with great stability.

> The height can be adjusted up to 40% to fit cases with limited

vertical room.

>“Self cleaning” design prevents the acumulation of plaque and

debris on the attachment which reduces wear and increases

longevity.

> Less maintenance and wear than traditional ball attachments.

Indications:

•C & B Mesial / Distal

•Limited Vertical Space

•Mesial / Distal of Implant Bars

•On Side of Implant Bars

•For Implant Abutments

14

> Offers all the benefits of the VS-3 Mini attachments with the

addition of extra support grooves for added stability.

> Eliminates the need for a lingual arm for situations where

metal arms are not desired and aesthetics are a must.

Indications:


•C & B Unilateral


VS-3 Mini Attachment System

VS-3 Mini Patrices

Lingual arm required for C & B applications

8 piece set #430 073 25

4 piece set #S47325

$73.50

$46.50

A friction style attachment that can be adjusted in height to accommodate cases with limited occlusal space. Ideal for mesial/distal applications as well as on implant bars. Fits anywhere a 1.7mm ball patrix can be used. Can be adjusted to adapt to the gingiva to prevent food impaction underneath.

A lingual arm and vertical groove is required for crown and bridge applications.

VS-3 Mini Duplicating Matrices

8 piece set #430 073 23

4 piece set #S47323

$52.50

$33.25

VS-3 Mini Wax Matrix Housings

8 piece set #430 073 20

4 piece set #S47320

$52.50

$33.25

VS-3 Mini 13 Part Kit

2 matrices VS-3 mini red 2 VS-3 mini patrices

2 matrices VS-3 mini yellow 2 wax matrix housings

2 matrices VS-3 mini green 1 VS-3 mini insertion pin

2 VS-3 mini duplicating matrices

VS-3 Mini 13 Part Kit #430 073 12

*Requires SV Mandrel #360 011 51

$73.50

$86.00

VS-3 Mini SV Attachment System

VS-3 Mini SV Patrices

No lingual arm required

8 piece set #430 073 43

4 piece set #S47343

$73.50

$46.50

A friction style attachment that can be adjusted in height to accommodate cases with limited occlusal space. Ideal for mesial/distal applications. Fits anywhere a 1.7mm ball patrix can be used. Can be adjusted to adapt to the gingiva to prevent food impaction underneath. Does not require a lingual arm or groove due to the stress distributor grooves.

VS-3 Mini SV Duplicating Matrices

8 piece set #430 073 41

4 piece set #S47341

$52.50

$33.25

VS-3 Mini SV Wax Matrix Housings

8 piece set #430 073 38

4 piece set #S47338

$52.50

$33.25

VS-3 Mini SV 13 Part Kit

2 VS-3 mini SV red matrices

2 VS-3 mini SV yellow matrices

2 VS-3 mini SV green matrices

2 VS-3 mini SV patrices

2 wax matrix housings

1 VS-3 mini SV insertion pin

2 VS-3 mini SV duplicating matrices

VS-3 Mini SV 13 Part Kit #430 073 30

*Requires SV Mandrel #360 011 51

$73.50

$86.00

VS-3 Mini Green Matrices - Retention Level 1

For low friction.

8 piece set #430 073 17

4 piece set #S47317

$52.50

$33.25

VS-3 Mini Yellow Matrices - Retention Level 2

For normal friction.

8 piece set #430 073 15

4 piece set #S47315

$52.50

$33.25

VS-3 Mini Red Matrices - Retention Level 3

For high friction.

8 piece set #430 073 13

4 piece set #S47313

$52.50

$33.25

VS-3 Mini Metal Housings

Made in

2 piece set #SA7317 $24.00

VS-3 Mini Insertion Pin

2 pieces #430 073 65

$21.95

SV Paralleling Mandrel

For the VS-3 Mini and the VS-3 Mini SV Patrix.

This universal mandrel can be used for many items including bars.

#360 011 51

$86.00

VS-3 Mini SV Green Matrices - Retention Level 1

For low friction.

8 piece set #430 073 35

4 piece set #S47335

$52.50

$33.25

VS-3 Mini SV Yellow Matrices - Retention Level 2


8 piece set #430 073 33

4 piece set #S47333

$52.50

$33.25

VS-3 Mini SV Red Matrices - Retention Level 3

For high friction.

8 piece set #430 073 31

4 piece set #S47331

$52.50

$33.25

VS-3 Mini SV Insertion Pin

2 pieces #430 073 64

$21.95


For the VS-3 Mini and the VS-3 Mini SV Patrix.

This universal mandrel can be used for many items including bars.

#360 011 51

$86.00

15

VS-3 Mini Instructions

Minimize the wear factor with the VS-3 Mini Attachment.

The larger retentive surface design of the VS-3 Mini Attachment will minimize wear of the male component.

VS-3 Mini

Adjust VS-3 Mini patrix from the bottom first

(angled area).

TIP: Use the SV Mandrel to hold the patrix while adjusting.

The patrix can be reduced up to 40% in height.

TIP: Use the SV Mandrel to gauge the amount of reduction for the patrix.

The VS-3 Mini patrix is waxed onto the copings using the SV Paralleling Mandrel.

A lingual arm rest seat with a groove is strongly recommended. It is established in wax using a milling machine or surveyor and the corresponding burs or tools.

The lingual arm rest seat with a groove is redefined after casting.

Porcelain crowns are finished and the VS-3 Mini patrices are polished lightly using Abraso Fix polishers (Item# 350 007 51)

The undercuts are blocked out and the case is duplicated with the yellow matrix in place.

After the refractory model is poured, wax is applied over the refractory matrix and contoured with the major connector.

Finished partial frame coated with Tooth Colored

Opaquer UV and Ropak Pink Opaquer UV.

(Item# 540 001 05) (Item#520 001 65)

Close up of lingual arm fitting flush into the shoulder rest with groove.

16

-Final Case Views-

VS-3 Mini SV Instructions

Minimize the wear factor with the VS-3 Mini SV Attachment.

The larger retentive surface design of the VS-3 Mini SV Attachment will minimize wear of the male component.

VS-3 Mini SV

Adjust VS-3 Mini SV patrix from the bottom first (angled area). The patrix can be reduced up to 40% in height.

The VS-3 Mini SV patrix is waxed onto the copings using the SV Paralleling Mandrel. A lingual arm is not required.

Porcelain crowns are finished and the VS-3 Mini

SV patrices are polished lightly using Abraso Fix polishers (Item# 350 007 51)

The model is duplicated with the yellow matrix.

The undercuts are blocked out and the case is duplicated.

After the refractory model is poured, wax is applied over the refractory matrix and contoured with the major connector.

Dimensions

Products

VS-3 Mini Patrix

VS-3 Mini Matrix

VS-3 Mini SV Patrix

VS-3 Mini SV Matrix

-Final Case Views-

Depth

2.3 mm

2.0 mm

4.1 mm

2.0 mm

Width

3.1 mm

3.0 mm

3.5 mm

Height

6.0 mm

6.0 mm

5.8 mm

Maximum

Reduction *

3.0 mm

3.0 mm

2.8 mm

2.6 mm 6.0 mm 2.8 mm

* Reduction of attachment more than recommended will result in loss of retention.

17

VKS-SG

18

Indications:


•C & B Bars

•C & B Unilateral





•Laser Welding

> The most versatile Bredent attachment system

> Cost effective and easy to use and maintain

> Available in two ball diameters, each with over 6 retention levels

> Can be used in cases with very limited room

> Retention clips are made of special Duroplast material which resists

deterioration in the oral environment

> Laser welding components also available

VKS-SG Attachment System

SG Patrix

8 piece set 2.2 mm #430 053 70

8 piece set 1.7 mm #430 067 00

$73.50

4 piece set 2.2 mm #S45370

4 piece set 1.7 mm #S46700

$46.50

Available in 2.2mm or 1.7mm ball diameters. Ideal for mesial/distal applications and cases with very limited room. The ball can be placed low to the tissue for excellent stability. A lingual arm and vertical groove is required for crown and bridge applications.

• C & B Mesial / Distal

• C & B Bar

• Limited vertical space

• Mesial / Distal of implant bars

• On side of implant bars

• For implant abutments

VKS-SG/SV Stress Distributor Patrix

Eliminates the need for a palatinal or lingual arm.

8 piece set *1.7 mm only #430 073 53

4 piece set *1.7 mm only #S47353

$73.50

$46.50

Offered in 1.7mm ball diameter only. Has two vertical grooves which eliminates the need for a lingual arm and makes it great for cases where metal showing is undesirable. Ideal for unilateral cases. Takes a bit more room than the regular SG Patrix. Requires the SV

Mandrel.

VKS Universal Patrix

Can be used with both the SG (horizontally) and the OC (vertically) attachments.

8 piece set 2.2 mm #430 053 80 4 piece set 2.2 mm #S45380


$73.50

$46.50

The small base makes it easy to attach to abutments and onto the side of bars.

SG Bar Patrix

Made in

Comes with 4 SG Patrices already paralleled on the bar in strategic positions.

2 piece set 2.2 mm (8 attachments) #S85370

2 piece set 1.7 mm (8 attachments) #S86700

$73.50

$73.50

Saves time and adds precision when fabricating implant bars. Creates more aesthetic bars as each patrix does not have to be waxed to the bar individually.

Requires the VKS Bar Mandrel or any parallel bar mandrel.

SG Green Matrix - Retention Level 1



$52.50

$33.25

SG Yellow Matrix - Retention Level 2



$52.50

$33.25

SG Red Matrix - Retention Level 3



$52.50

$33.25

SG Super Snap Light Green Matrix - Retention Level 4

4 piece set 2.2 mm #430 SG 204 4 piece set 1.7 mm #430 SG 104

$38.50

$38.50

SG Super Snap Light Yellow Matrix - Retention Level 5


$38.50

$38.50

SG Super Snap Light Red Matrix - Retention Level 6


$38.50

$38.50


4 piece set 1.7 mm #430 SG 107

$38.50

SG Super Snap Light Yellow Matrix - Retention Level 8


$38.50

$38.50

SG Super Snap Light Red Matrix - Retention Level 9


$38.50

$38.50



$38.50

$38.50


• C & B Unilateral


• C & B Bar



• On top of implant bars

• Telescopic

• C & B Bar

• Mesial / Distal of Implant Bars


VKS-SG 4 Piece Set

SG Matrix: Red, Yellow & Green

1 Metal SG Housing

1.7mm #SA6630 $46.50

2.2mm #SA5360 $46.50

VKS Model Analogs

Metal analogs for replicating the VKS ball.

8 piece set 2.2mm 430 054 82 4 piece set 2.2 mm #S05482

8 piece set 1.7mm 430 066 20 4 piece set 1.7 mm #S06625

$63.50

$38.25

Made in

Metal SG Matrix Housings

2 piece set 2.2mm #SA5410 $24.00

2 piece set 1.7mm #SA6680 $24.00

Made in

Castable SG Matrix Housings

8 piece set 2.2mm #S05420 4 piece set 2.2 mm #SA5420

8 piece set 1.7mm #S06660 4 piece set 1.7 mm #SA6660

$52.50

$33.25

Assortment Kit:

4 pieces 1.7mm + 4 pieces 2.2 mm #S06620

$52.50

14 piece kit #SW2660

$12.00

Wax Bar 1.9 x 4 x 50 mm


Wax Bar 2.2 x 6 x 50 mm


Wax Bar 1.6 x 8 x 50 mm

$12.00

$12.00

These products are made in the USA for XPdent.

They are not Bredent, Germany products.

19


VKS Paralleling Mandrel

Ensures that the attachments are parallel and secured in place precisely.

2.2mm #360 011 30

1.7mm #430 067 70

$52.50

$52.50

VKS Insertion Pin

Is used by technicians and dentists to place the matrices into the housings.

2.2mm #430 054 80

1.7mm #430 062 10

$21.95

$21.95

Bar Mandrel

For the SG Bar Patrix and any other parallel bars.

#430 062 30

$52.50


For the VKS-SG/SV Stress Distributor Patrix. This universal mandrel can be used for many items including bars.

#360 011 51

$86.00

20

VKS-SG 10 Part Kit

2 matrices SG red 2 patrices SG

2 matrices SG yellow

2 matrices SG green

1 insertion pin VKS

1 paralleling mandrel VKS

10 Part Kit 2.2 mm #430 053 30

10 Part Kit 1.7 mm #430 067 30

$126.00

$126.00

VKS-SG 8 Part Kit

2 matrices SG red 2 matrices SG green

2 matrices SG yellow 2 patrices SG

8 Part Kit 2.2 mm #430 053 60

8 Part Kit 1.7 mm #430 066 30

$63.50

$63.50

VKS-SG 6 Part Matrix Kit

2 matrices SG red 2 matrices SG green

2 matrices SG yellow

6 Part Kit 2.2 mm #S25360

6 Part Kit 1.7 mm #S26630

$46.00

$46.00

VKS-SG 3 Part Matrix Kit

1 matrix SG red 1 matrix SG green

1 matrix SG yellow

3 Part Kit 2.2 mm #S15360

3 Part Kit 1.7 mm #S16630

$29.00

$29.00

Dimensions

4.4 mm

2.8 mm

2.2 mm Matrix

4.2 mm

3.0 mm

3.3 mm

2.4 mm

1.7 mm Matrix

6.2 mm

2.9 mm 2.4 mm

1.9 mm

4.3 mm

1.7 mm SG-SV side view

VKS-SG/OC 2.2mm Introductory Kit

4 matrices OC red 2.2 2 patrices OC 2.2

4 matrices OC yellow 2.2 2 patrices SG 2.2

4 matrices OC green 2.2 2 patrices UNI 2.2

2 matrices OC metal 2.2 4 blocking out discs 2.2

2 matrices SG red 2.2 1 each wax bars 1.6/1.9/2.2

2 matrices SG yellow 2.2 1 paralleling mandrel VKS 2.2

2 matrices SG green 2.2 1 insertion pin VKS 2.2

2.2mm Introductory Kit #430 053 00 $267.00

VKS-OC/SG 1.7mm Introductory Kit

2 matrices OC red 1.7 2 patrices SG 1.7

2 matrices OC yellow 1.7 2 patrices UNI 1.7

2 matrices OC green 1.7 2 blocking out discs 1.7

2 matrices OC metal 1.7 1 each wax bars 1.6/1.9/2.2

2 matrices SG red 1.7 1 paralleling mandrel VKS 1.7

2 matrices SG yellow 1.7 1 insertion pin VKS 1.7

2 matrices SG green 1.7

1.7 mm Introductory Kit #430 065 10

$242.00

VKS-SG/SV Stress Distributor 9 Part Kit

2 matrices SG red 1.7 2 stress distributor patrices SG/SV

2 matrices SG yellow 1.7 1 insertion pin VKS 1.7


*1.7 mm only Order #430 073 52 $82.00

*Requires SG/SV Mandrel

#360 011 51 $86.00

6.2 mm

3.6 mm

1.7 mm SG-SV front view

Example of a proper lingual arm

(Rest with vertical groove)

2.2 mm

3.0 mm

0.7 mm

3.0 mm

2.2 mm Universal Patrix

1.7 mm

2.1 mm

0.4 mm

2.1 mm


4.7 mm

5.4 mm 3.3 mm

2.2 mm Castable Housing

3.8

mm

4.5 mm

2.9 mm

1.7 mm Castable Housing

VKS-SG Exchangeable Stud

Safety, precision and biocompatibility due to easily exchangeable titanium stud.

VKS-SG 2.2 exchangeable stud VKS-SG 1.7 exchangeable stud

The stud-head screw is only slightly screwed into the threaded sleeve and held to the wax model using the paralleling mandrel.

The attachment patrix is waxed to the wax model in the path of insertion of the shear distributor with parallel interlock.

The stud-head screw is turned out

(counter clockwise) of the threaded sleeve using the screwdriver.

Prior to investing the model, the studhead screw must be replaced by the casting screw.

Colloidal graphite (#540 007 06) is applied onto the thread of the casting screw; then the screw is turned into the threaded sleeve exerting minimum force.

The casting is sandblasted and the casting screw is turned out. The crowns are finished and the stud-head screw is turned in.

Finished and polished with Abraso-Star

Glaze (#520 001 63).

The yellow matrix is placed on the stud and the model is prepared for duplicating.

21


VKS-SG Exchangeable Stud

VKS-SG Threaded sleeve

HSL (Au, Pt, Pd), melting range: 1320 - 1460 o

C

Casting temperature cannot exceed 1270 o

HSL, 1 piece 2.2 mm


C

#450 000 51

#450 000 59

Platinum-Iridium (Pt, Ir), Melting range: 1820 - 1850 o

C

All commercial dental alloys except titanium may be used.

Pt-Ir, 1 piece 2.2 mm


#450 000 52

#450 000 60

VKS-SG Stud-head screw

1 piece, titanium

2.2 mm #450 000 47

1.7 mm #450 000 56

$32.00

$32.00

$75.00

$75.00

$91.00

$91.00

Casting Screw for 2.2 mm

1 piece #450 000 48


1 piece #450 000 57

$28.50

$28.50

Screwdriver 2.2 mm for 2.2 mm stud head screw

#330 006 90

$33.95

Screwdriver 1.7 mm for 1.7 mm stud head screw

#330 011 64

$33.95

VKS-SG 1.7 Exchangeable Stud Assortment Kit

1 thread sleeve VKS-SG platinum, 1.7 1 casting screw M1.6

1 matrix VKS-SG 1.7 red 1 stud-head screw VKS-SG titanium, 1.7

1 matrix VKS-SG 1.7 yellow

1 matrix VKS-SG 1.7 green

1.7 kit

1 screwdriver short, 1.7

1 paralleling mandrel, 1.7

#450 000 61 $199.00

VKS-SG 2.2 Exchangeable Stud Assortment Kit

1 thread sleeve VKS-SG platinum, 2.2 1 casting screw M2

1 matrix VKS-SG 2.2 red 1 stud-head screw VKS-SG titanium, 2.2

1 matrix VKS-SG 2.2 yellow

1 matrix VKS-SG 2.2 green

1 screwdriver short, 2.2

1 paralleling mandrel, 2.2

2.2 mm kit #450 000 49 $199.00

VKS-SG Threaded sleeve

Available in two alloys:

• HSL (Au, Pt, Pd), melting range: 1320 - 1460


C.

o

C

• Platinum-Iridium (Pt, Ir), Melting range: 1820 - 1850 o

C



• C & B Bar




• For implant abutments

A threaded sleeve is cast into the crown and the machined ball patrix is screwed on after the case is done. This eliminates casting errors and provides a perfect ball patrix. This also allows the ball to be exchanged in the future in case it ever gets damaged or worn.

Tap for Exchangeable Stud

#460 001 17

1.7 mm

$139.00

The new Titanium Bar Patrix has three parallel threaded holes to accept the Exchangeable SG Stud. Fabrication of implant bars in 3 easy steps: (1) The bar is sectioned to the desired length(s). (2) The bar sections are laser welded into place. (3) The SG attachments are screwed into the bar.


• Laser welding

Titanium Bar Patrix 1.7 mm

#450 0SA 17 $93.00

Titanium Bar Patrix 2.2 mm

#450 0SA 22 $93.00

VKS-SG Stud Screw 1.7mm

#450 000 56

$32.00

VKS-SG Stud Screw 2.2mm

#450 000 47

$32.00


#460 001 22

2.2 mm

$139.00

Made in

Tap Holder

#S07340

$26.50

22

Custom Metal Housing with Lingual Arm

For repairs and fabrication of new cases

Two splinted crowns with a 1.7mm SG and milled shoulder rest with an interproximal locking groove.

A 1.7mm yellow matrix is placed inside a

1.7mm castable housing (#SA6660) and snapped over the ball.

The retention tail of the castable housing is cut off and saved. Now, using a surveyor and an SV Mandrel (# 36001151) the castable housing with yellow matrix inside, are secured in a parallel path of insertion. Pikuplast modeling resin (Yellow

#54000217) is applied onto the shoulder rest and groove, on the crown, to create the lingual arm as a uniform part of the castable housing.

The retention tail can be further modified if necessary and then tacked on the castable housing following the shape of the ridge, using Pikuplast. Note: use a

surveyor and SV Mandrel (#36001151) for easier placement.

Lift off the custom, castable housing with lingual arm pattern and cast as usual.

Grind in some mechanical retentions, sandblast and opaque using Ropak (Powder

#52000165 and Liquid #52000164) light curing opaquer to mask out the metallic color. Polish lingual arm to a high shine, block-out all undercuts with wax and paint acrylic separator on the model.

“Hollow out” the acrylic and/or metal in the areas of the RPD where the new metal housing will be installed.

Apply self-curing pink acrylic to secure the new metal housing with lingual arm.

Once acrylic has set, finish and polish as normal.

23

Instructions

SG Impression Analog Instructions.

After the crowns/bridge have been created, it is recommended to pickup the crowns in an impression rather than cementing them and then pulling an impression. However, in the event that the restoration has been permanently cemented, the removable laboratory will need an accurate model to work on. This can be made by following these easy steps.

It is important not to slide any of the matrices onto the ball patrices before taking the impression. An accurate reproduction of the male patrix will suffice to produce a precise model.

A rigid impression material such as Impregum or hard Polyvinyl should be used to accurately capture the crowns and the SG patrices. The impression may tear to release from the ball, this is normal and will not affect the accuracy of the model.

The VKS analog can be bent to a 90 degree angle which will allow the retention post to be embedded into the die stone properly.

The analog is inserted into the impression of the ball patrix with the retention tail pointing upwards. If needed, a little wax can be used to hold it in place securely.

The impression is poured using standard techniques. This gives an accurate model with a metal representation of the SG patrix in the correct position.

For hygienic reasons, clean the case before removing the old matrix.

Make a slice down the middle of the matrix.

This makes it easier for the clip to fold over on itself when being removed.

Insert the scalpel behind the matrix …

… and pry it out forcefully.

After the matrix is removed, clean the housing properly to ensure that no debris gets trapped under the new clip.

Put the new matrix onto the tip of the insertion tool and hold it in place with your finger.

24

Push the matrix into the housing forcefully.

An audible snap should be heard.

The case is now ready to be seated.

VKS-SG/OC Bond-In Exchangeable Stud

Create Retrievability and Serviceability of Attachment Cases.

The VKS-SG/OC Bond-in Exchangeable Stud System provides a variety of benefits tailored to increase the lifespan of attachment retained removable prosthetics. Featuring a titanium ball screw which is less susceptible to wear compared to those cast out of alloys commonly used in the dental laboratory. However, in the rare cases where a titanium ball screw should wear out and cause loss of retention; then the dentist can easily unscrew the worn ball and replace it with a new one. In the worst case scenario… if damage to the threaded sleeve should occur, the dentist can carefully grind it out and bond in a new threaded sleeve to restore the attachment assembly.

The VKS-SG/OC Bond-in Exchangeable Stud creates a completely retrievable and serviceable, precision removable prosthesis. Technicians will avoid unnecessary aggravations using a high quality, simple and cost-effective attachment system.

Dentists can confidently deliver to their patients an attachment case with superior, long term maintenance capabilities that

will save them both time and money.

A 1.7mm auxiliary modeling element (#450 000 73) is placed into a VKS paralleling mandrel and is waxed to the coping using a surveyor. The modeling element creates a 0.5mm larger receptacle to accommodate the cement used to bond in the threaded sleeve.

After wax has been applied around the auxiliary modeling element, it is carefully removed. Note: a vertical guide plane is created by applying wax directly onto the paralleling mandrel while waxing-in the modeling element.

Completed wax-up and ready to sprue for casting.

Lingual arm shoulder rest and groove are redefined and castings are finished as usual.

Porcelain work is finished and metal areas are polished. Note: sandblast the hole lightly to remove any excess porcelain material.

1.7mm titanium threaded sleeve, stud-head screw and screwdriver.

Stud-head screw is carefully screwed into the threaded sleeve; use minimal pressure.

NOTE: Because of the intricate design of the 1.7mm stud-head screw, the screwdriver is designed to break before the ball

platform should excess force be used.

25

After screwing the components together, the stud-head screw and threaded sleeve are placed into the VKS paralleling mandrel held in a surveyor.

Use high quality anaerobic cement and apply it evenly into the hole created by the auxiliary modeling element.

NOTE: Make sure to insulate with separating medium any areas where bonding cement is not desired such as, the model, paralleling mandrel, etc.

Use the surveyor to insert the ball screw/threaded sleeve assembly into the receptacle coated with cement and allow it to set. Using the surveyor will ensure that the attachment is set absolutely parallel.

VKS-SG/OC Exchangeable Stud

Bond-in Auxiliary Modeling Element

2.2 mm #450 000 75

1.7 mm #450 000 73

$30.50

VKS-SG/OC Exchangeable Stud

Bond-in Titanium Threaded Sleeve

2 pieces

2.2 mm #450 000 76

1.7 mm #450 000 74

$45.50

After the cement has set, release the mandrel from the attachment and inspect. At this time any excess cement can be picked off using a scalpel and fabrication of the RPD can begin.

Kits:

VKS-SG/OC 2.2 Exchangeable Stud w/

Titanium Bond-In Thread Sleeve

Assortment Kit

2 VKS-Stud-head screw 2.2mm

2 Auxiliary modeling element

2 Bond-in titanium thread sleeve

2.2mm 6 Part Kit #S60076 $163.00

VKS-SG/OC 1.7 Exchangeable Stud w/ Titanium Bond-In Thread Sleeve

Assortment Kit

2 VKS-Stud-head screw 1.7mm



1.7mm 6 Part Kit #S60074 $163.00

Accessories

VKS-SG/OC Stud-Head Screw

1 piece, Titanium

2.2 mm #450 000 47

1.7 mm #450 000 56

$32.00



Assortment Kit

2 VKS Stud-head screw 2.2mm



1 VKS paralleling mandrel 2.2mm

1 Screwdriver for 2.2mm stud screw

2.2mm 8 Part Kit #S80076 $242.00



Assortment Kit

2 VKS Stud-head screw 1.7mm



1 VKS paralleling mandrel 1.7mm

1 Screwdriver for 1.7mm stud screw

1.7mm 8 Part Kit #S80074 $242.00

26

NEW!

DTK Adhesive Kit

A dual hardening composite adhesive for the fi xation of dental attachments.


#540 001 06

$125.00

(See page 51)



2.2 mm #360 011 30

1.7 mm #430 067 70

$52.50


#460 001 17

1.7 mm

$139.00

Screwdriver 2.2 mm

for 2.2 mm stud head screw

#330 006 90

$33.95

Screwdriver 1.7 mm

for 1.7 mm stud head screw

#330 011 64

$33.95


#460 001 22

2.2 mm

$139.00

Case

Designs

VKS-SG Bar Upper

VKS-SG Patrix - Lingual arm & vertical groove required

VKS-SG SV Patrix - No lingual arm required

Tray Material UV

Highly stable light-curing resin for trays and base plates.

The flexibility of the material allows easy placement onto the model without tearing. The required shape can be cut with an instrument. The pink color provides the perfect basis for the set-up.

Tray Material UV band

2.5 mm x 90 mm, 1350 g

#540 001 66

$105.00

The high flexibility of the material simplifies the placement onto the model.

The material will not be damaged.

The tray material can be precisely cut with any instrument. Accordingly, the amount of work is reduced.

Perfect adaptation to any situation guarantees uniform wall thicknesses.

Due to the high stability the position of the handle which has been determined will not be changed during the polymerization process.

The high stability of the tray material avoids deformation during impressiontaking. Precise models will be obtained.

The pink color offers the perfect basis for any type of set-up.

As a basic material for bite patterns or functional trays with bite rims, the resin ensures that the work will not be deformed.

27


VKS-SG Instructions for distal extensions

The SG Patrix is waxed onto the copings with the VKS

Paralleling Mandrel. The use of a surveyor to parallel the patrices is necessary. It is recommended to use a lingual support arm with a positive rest. The square backing of the patrix serves as a path of insertion but can be reduced in height and width. Take care not to lose the positive seat on the flat side of the attachments.

The short part of the patrix needs to be placed towards the tissue (see diagram on right). The patrix should be placed as close to the tissue as possible without interfering with the interproximal.

Placing the attachment low on the tooth or bar improves stability and places less stress on the teeth and implants.

After casting and fitting on the model, polish the attachment lightly. If the attachment is not polished, residue and oxide may wear the matrices prematurely.

Caution should be taken while finishing and polishing the subframe. The attachment ball should not be ground upon or highly polished as it would lose retention and damage the attachment.

To create the overcasting, the model needs to be duplicated with the yellow matrix in place. The yellow matrix, therefore, basically acts as a duplicating jig but is removed and can be reused at a later date.

It is extremely important that all the matrices are placed parallel to each other to create a singular insertion/removal path. All undercuts of the frame and matrix need to be blocked out and absolutely no wax should be on the matrix when it is duplicated.

This shows the refractory model of the case. The refractory model is basically a duplicate model made in investment material. Notice the refractory

“dummy” of the yellow matrix. It is imperative not to scratch or damage the matrix or any of the areas that will be waxed over.

After the refractory model is created, the chrome cobalt overframe is simply waxed as required. Waxing over the refractory matrix will create the housing for the attachment matrices. A lingual arm should be incorporated into the framework for partials.

Bredent retention crystals or beads could be placed on the wax framework to create a more retentive surface for the acrylic. Once spread, the entire model

& wax-up is invested.

The framework is then cast and fitted. A light deplating of the chrome cobalt framework casting is usually required to clean and polish the interior of the attachment metal housing. If a higher electropolish of the framework is required, it is necessary to block out the housing interior with a drop of wax to prevent overpolishing. Overpolishing could result in loss of friction.

To place the matrix into the framework, simply use the insertion pin and push the matrix into place.

Because the attachments are completely mechanical, no acrylic is required to hold the matrix in place. To change the friction of the attachment, a small bur is used to tear the old matrix out of the housing and the new matrix is placed as usual. When replacing a matrix, it is suggested to replace the old matrix with a matrix of the same color/friction. If an adequate retention is still not achieved, then the next higher friction matrix should be used. As with all attachments, the patients need to know that the appliance should not be inserted by biting into place - it needs to be inserted via hand pressure. Biting any attachment into place causes extreme forces that wear down the attachment prematurely.

28

VKS-SG SV Instructions

The SG SV patrix has two vertical grooves that serve the same purpose as a lingual arm, thus eliminating the need to wax a lingual rest. When placing the patrix, the SV paralleling mandrel must be used.

After casting and fitting, polish the attachment lightly.

This is an extremely aesthetic solution as there is no metal showing from lingual arms or rests and the crowns can be built up fully with porcelain.

To create the overcasting, the yellow matrix must be placed on the ball. It is extremely important that all the matrices are placed parallel to each other and to the grooves of the patrix.

All undercuts of the frame and matrix need to be blocked out and absolutely no wax should be on the matrix when it is duplicated. After duplication, the yellow matrix is removed and salvaged.

The refractory model is basically a duplicate model made in investment material. Notice the refractory

“dummy” of the yellow matrix. It is imperative not to scratch or damage the matrix, grooves or any of the areas that will be waxed over.

The chrome cobalt overframe is waxed as required.

Waxing over the refractory matrix will create the housing for the attachment matrices. For the SG-

SV attachment, the framework wax-up must cover the vertical grooves. The entire model & wax-up is then invested.

The framework is then cast and fitted. A light deplating of the chrome cobalt framework casting is usually required to clean and polish the interior of the attachment metal housing. If a higher electro-polish of the framework is required, it is necessary to block out the housing interior with a drop of wax to prevent overpolishing.

To place the matrix into the framework, simply use the insertion pin and push the matrix into place. No acrylic is required to hold the matrix in place. Notice how the partial framework wraps around into the grooves. This provides precision and stability that makes the SG-SV attachment extremely suitable for uni-lateral cases.

VKS-SG Bar Patrix Instructions

The SG Bar Patrix significantly reduces the time required to wax up bars with the SG attachment as they are already pre-paralleled on the bar. The SG Bar Patrix is first cut to the desired length using a disc.

Any remaining sections of the bar can be saved to be used at a later date. The bar is paralleled onto the implant abutments or crowns using any bar mandrel and waxed into place. The bredent bar mandrel (430 062 30) is ideal.

Since the patrices are already parallel on the bar, there is no need to use the VKS paralleling mandrel. The case is cast, duplicated and finished according to figures 6-12 of “instructions for the side of a bar” above.

29

VKS Stud Reworking Set

Repair worn VKS stud attachments

Symptoms of wear at the stud of the VKS attachment lead to the loss of the function of the denture. Normally, the patient requires a new prosthetic supply which includes the risk that the root of the abutment tooth may be damaged considerably and can no longer be used to hold the denture. To avoid these risks and additional cost, the

VKS stud reworking set has been developed. For hygenic purposes, used instruments should not be reused; they must be disposed off. Use the VKS stud reworking set only for gold alloys. This kit allows the worn VKS patrix (stud) to be milled in the patient’s mouth to a cylindrical post over which a new titanium ball can be placed.

Remember:

1) Can only be used on gold alloys.

2) Can be performed chairside or implant bars

can be repaired by the technician.

VKS Reworking Kit

2 repair burs

2 stud sleeves

2 height stops

2 spacer discs

1 tap for external thread

2.2 mm #860 001 90

1.7 mm #860 001 80

$349.00

$349.00

Repair Bur

1 piece

2.2 mm #860 001 10

1.7 mm #860 001 00

$65.50

Height Stop

1 piece

2.2 mm #860 001 30

1.7 mm #860 001 20

$32.50

Tap for External Thread

1 piece

2.2 mm #860 001 70

1.7 mm #860 001 50

$61.50

Stud sleeves

1 piece

2.2 mm #860 001 40

1.7 mm #860 001 60

$50.50

Spacer Discs

2 pieces

2.2 mm #860 002 10

1.7 mm #860 002 00

$29.50

Clamp the VKS repair bur into the angle handpiece. Put the repair bur to the centre of the worn stud and hold it towards the direction of insertion of the denture; only then milling is started. Mill the residual stud parts at a maximum speed of 5000 rpm until a cylindrical post is obtained.

The post that was produced with the repair bur is shortened to a defined length using the height stop. Clamp the height stop into the angle and piece and place onto the cylindrical post together with the guide sleeve. Shorten the cylindrical post at a maximum speed of 5000 rpm until the guide sleeve of the height stop rests on the platform below the post. Adequate cooling must be ensured by the operator.

Cut a thread on the cylindrical post. Add a small drop of cooking oil onto the cylindrical post and into the tap. Put the tap onto the cylindrical post in the direction of insertion and turn clockwise exerting slight pressure. After the first turn the thread can be completed without exerting any pressure to the tap. During this process the tap is turned back by a half turn after each full turn. This process is repeated until the tap rests on the platform below the cylindrical post. By turning anticlockwise, the tap can be removed. Clean and dry the thread.

Prior to gluing on the stud sleeve it must be ensured that the thread post in the patient’s mouth is grease-free and dry. Hold the stud sleeve on the holding element, spread a small quantity of adhesive in the internal thread of the stud sleeve using a pointed object and screw it on the threaded post. After the adhesive hardens, the supporting post can be cut off with a separating disc, the surface can be smoothed with a rubber polisher and excess adhesive can be removed with a pointed object. The surface of the stud must not exhibit any scratches.

30

Drill-

N

-Tap Retrievable Ball Screw

Salvage worn implant cases...

...or fabricate new cases with the benefi ts of retrievability.

The Drill-N-Tap Retrievable Ball Screw

(Made of Titanium) from XPdent is designed to be used for replacing worn out attachments on implant bars and abutments. Also recommended for fabricating new implant cases.

Dimensions of Ball Screws:

Thread sleeves: 4.0 mm

Thread diameter:

Ball diameter:

Pilot hole size:

Tap size:

M2 x .4

2.2 mm

1.8 mm

M2 x .4

Tools & equipment

Available in two kits 2.2 mm only:

•Titanium/non-precious #ST7000

•Precious #SP7000

Made in

Titanium Ball Screws

Two pieces, 2.2 mm

#S27000 $29.95

Short Screwdriver

#330 006 90 $33.95

Made in

Tap

#S07293-T $32.95

Made in

Tap Holder

#S07340 $26.50

Tungsten Carbide Center Drill

#330 006 60 $39.50

Diatit Multidrill 1.3 mm x 5.0 mm

#330 011 57 $44.50

Drill-N-Tap Retrievable Ball Screw Kit for Precious Metal

2 Titanium Ball Screws

Made in

1 Short screwdriver

1 Tap

1 Tungsten Carbide Center Drill

1 Diatit Multidrill 1.8 x 6.0 mm

#SP7000 $169.00

Milling & Drilling Oil

#550 000 08 $25.50

Drill-N-Tap Retrievable Ball Screw Kit for Non-Precious & Titanium

2 Titanium Ball Screws

Made in

1 Short screwdriver

1 Tap

Made in

1 Tungsten Carbide Center Drill



#ST7000 $210.00

Diatit Multidrill 1.8 mm x 6.0 mm

#330 008 00 $44.50

NEW!




#540 001 06

$125.00

(See page 51)

31

Step by Step Construction of an Implant Bar Using the Drill and Tap Ball Screw SG

Step 1 Step 2 Step 3

Drill a 1.5mm hole into your preferred plastic/ wax bar pattern using a Diatit Multidrill 1.5mm

# 33000730.

Install the pre-drilled bar patterns using a surveyor and the Bar Mandrel item # 43006230.

If the holes are drilled too large then use the

Waxing Pin # 44000656 analog from the Locking

Pin system to re-size the holes to 1.5mm. Finish the bar wax-up, sprue and invest in the usual manner.


After casting, the implant bar is milled and finished.

Pilot holes are re-sized to 1.8mm using the Diatit

Multidrill 1.8mm #33000800. The use of Milling

Oil #55000008 during this process is important.

Note: Multidrill bur speed should not exceed

5000rpm.

After cleaning any debris left from drilling, the

1.8mm hole is ready to be tapped to receive the

2.0mm ball screw.


The tap from the Security Lock system

# S07293-T will be used to cut the threads.

Coat the hole and the cutting area of the tap with Milling Oil #55000008. Insert the tap into a holder. Align the tap tool with the hole and begin turning slowly in a clockwise direction and then when binding occurs back out the tap tool

(counterclockwise) and then proceed again slowly

(clockwise).

Tip: It is recommended to use Milling Oil to reduce binding and ensure a clean, easy and precise threaded hole.

Insert the ball screws to check for accuracy.

32


Cut off the excess screw shaft.

Step 13

Snap a 2.2mm SG yellow matrix onto the ball to ensure proper positioning of ball screw.

Step 14

With the SG yellow matrix still in place, grind the remainder of the screw body flush to the implant bar using a milling machine or laboratory handpiece.

Step 15

Select a high quality bonding cement such as

Parapost or Panavia to bond the ball screws into the implant bar.

Note: Follow the manufacturer’s instructions for cementation to achieve optimal bond results.

Coat the threaded portion of the ball screw with cement.

Step 16 Step 17

Coat the hole with cement as well.

Screw the ball in place carefully.

Step 18

Allow the cement to set for the timeframe indicated by the manufacturer.

Step 19

Clean off any excess cement Implant bar is now ready to have an overcasting fabricated.

33

VKS-OC

Indications:


•C & B Bars


•Root Cap / Abutment



•On Top of Implant Bars


•Direct Ball Implant Abutments

•Laser Welding

34

> Cost effective and easy to use and maintain

> Available in two ball diameters, each with over 6 retention levels

> Can be used in cases with very limited room

> Retention clips are made of special Duroplast material which resists deterioration in the oral environment

> Laser welding components also available

VKS-OC Attachment System

Remember to always:

1) Use a lingual arm (Except for SV)

OC 2.2 mm Patrix

8 piece set 2.2 mm #430 053 90

4 piece set 2.2 mm #S45390

$73.50

$46.50

2) Use a metal with at least 230 Vickers Hardness

3) Use a metal housing

“Trailer Hitch style” with a 2.2mm ball. Ideal for mesial/distal applications and cases with limited vertical space. “Trailer hitch” arm has an approximate angle of 45 degrees. Can be placed low to the tissue for excellent stability. A lingual arm and vertical groove is required for crown and bridge applications.

OC 1.7 mm 60° Patrix

8 piece set 1.7 mm #430 073 47

4 piece set 1.7 mm #S47347

$73.50

$46.50




OC 1.7 mm 30° Patrix

8 piece set 1.7 mm #430 073 45

4 piece set 1.7 mm #S47345

$73.50

$46.50

“Trailer hitch style”. Ideal for mesial/distal applications and cases with limited vertical space. Can be placed low to the tissue for excellent stability. A lingual arm and vertical groove is required for crown and bridge applications. “Trailer hitch” arms come in two different angles to accommodate the various shapes and or defects of the residual ridge.

VKS Universal Patrix

Can be used with both the SG (horizontally) and the OC (vertically) attachments.



$73.50

$46.50

The small base makes it easy to attach to abutments and onto the side of bars.

OC Green Matrix - Retention Level 1

For low snap-in friction.



$52.50

$33.25

OC Yellow Matrix - Retention Level 2

For normal snap-in friction.



$52.50

$33.25

OC Red Matrix - Retention Level 3

For high snap-in friction.



$52.50

$33.25

OC Super Snap Green Matrix - Retention Level 4

For slightly higher snap-in friction.

4 piece set 2.2 mm #430 OC 204 4 piece set 1.7 mm #430 OC 104

$38.50

$38.50

OC Super Snap Yellow Matrix - Retention Level 5

For very high snap-in friction.


$38.50

$38.50

OC Super Snap Red Matrix - Retention Level 6

For maximum snap-in friction.


$38.50

$38.50

OC Super Snap Green Matrix - Retention Level 7

For slightly higher snap-in friction.

4 piece set 1.7 mm #430 OC 107

$38.50

OC Metal Matrix

Is resistant to oral conditions, extends matrix longevity and enables easier replacement of the attachments.



$152.00

$88.95

• C & B Bar



• On top of implant bars

• Telescopic

VKS-OC 4 piece set

OC matrix: 1 red, 1 yellow, 1 green

1 metal housing

1.7 mm #SA6720 $53.50

2.2 mm #SA5350 $53.50



2.2mm #360 011 30

1.7mm #430 067 70

$52.50

$52.50

VKS Insertion Pin


2.2mm #430 054 80

1.7mm #430 062 10

$21.95

$21.95

VKS Model Analogs

Metal analogs for replicating the VKS ball.

8 piece set 2.2mm #430 054 82 4 piece set 2.2 mm #S05482

8 piece set 1.7mm #430 066 20 4 piece set 1.7 mm #S06625

$63.50

$38.25

OC Blocking Out Disc

To aid the blocking out process for duplicating and to ensure that the Matrix sits parallel on the Patrix. If the case is processed without using this disc, the Matrix may sit at an angle and wear out prematurely.

8 piece set 2.2 mm #S05400 4 piece set 2.2 mm #S45400


$42.00

$24.25


$12.00

Wax Bar 1.9 x 4 x 50 mm


$12.00

Wax Bar 2.2 x 6 x 50 mm 8 piece kit #SW2650

$12.00

Wax Bar 1.6 x 8 x 50 mm

35

VKS-OC Exchangeable Stud

Safety, precision and biocompatibility due to easily exchangeable titanium stud.

Working is continued with the vks-oc

2.2 mm matrices.

VKS-OC 2.2 exchangeable stud VKS-OC 1.7 exchangeable stud

...or with the vks-oc rs 2.2 mm.

The stud-head screw is only slightly screwed into the threaded sleeve and held to the root cap wax-up using the paralleling mandrel.

The attachment patrix is waxed to the wax model in the path of insertion.

The stud-head screw is turned out

(counter clockwise) of the threaded sleeve using the screwdriver.

36

Prior to investing the model, the studhead screw must be replaced by the fixation screw.

Colloidal graphite (#540 007 06) is applied onto the thread of the casting screw; then the screw is turned into the threaded sleeve exerting minimum force.

The casting is sandblasted and the casting screw is turned out. The crowns are finished and the stud-head screw is turned in. The stud-head screw is polished to high luster using titanium polishing paste.


VKS-OC Exchangeable Stud

VKS-OC Stud-Head Screw

1 piece, titanium

2.2 mm #450 000 47

1.7 mm #450 000 56

$32.00

$32.00

VKS-OC Threaded Sleeve


C

Casting temperature cannot exceed 1270



o

C.

#450 000 46

#450 000 54

$75.00

$75.00

Platinum Iridium (Pt, Ir), Melting range: 1820 - 1850 o

All commercial dental alloys except titanium may be

C used.



#450 000 53

#450 000 55

$91.00

$91.00


1 piece #450 000 48


1 piece #450 000 57

$28.50

$28.50

Screwdriver 2.2

For 2.2 mm stud head screw.

#330 006 90 $33.95

Screwdriver 1.7

For 1.7 mm stud head screw.

#330 011 64 $33.95

VKS-OC 2.2 Exchangeable Stud Assortment Kit

1 thread sleeve VKS-OC 2.2 platinum-iridium 1 paralleling mandrel, 2.2

1 stud-head screw-OC 2.2 titanium

1 screwdriver, 2.2

# 450 000 45 $199.00

1 casting screw M2

VKS-OC 1.7 Exchangeable Stud Assortment Kit

1 thread sleeve VKS-OC 1.7 platinum-iridium 1 paralleling mandrel, 1.7

1 stud-head screw-OC 1.7 titanium

1 screwdriver, 1.7

# 450 000 58

$199.00

1 casting screw M1.6

Universal Metal Patrix

For cast-on or solder-on purposes.

Can be used with both the SG and the OC attachments.


C.

o

C

Casting temperature cannot exceed 1270

2 piece set 2.2mm #430 070 00 2 piece set 1.7mm #430 070 10

$108.00

$108.00

VKS-OC Stud-Head Screw

1 piece, titanium

2.2 mm #450 000 47

1.7 mm #450 000 56

$32.00

$32.00


#460 001 17

1.7 mm

$139.00

VKS-OC Threaded sleeve

Available in two alloys:

• HSL (Au, Pt, Pd), melting range: 1320 - 1460


C. o

C

• Platinum-Iridium (Pt, Ir), Melting range: 1820 - 1850 o

C


• C & B Bars

• Root Cap / Abutment

• On Side of Implant Bars


#460 001 22

2.2 mm

$139.00

Tap Holder

#S07340

$26.50

Made in

Advisory:

It is highly recommended to advise patients not to bite, but to hand insert their restoration into place.

Biting any attachment case into place can cause premature wearing of the components. It is also recommended to use metal housings for the matrices. Without them, the cases will have substandard retention and will wear faster than normal. The metal used must have a hardness of at least 230 vickers.

These products are made in the USA for XPdent.

They are not Bredent, Germany products.

37


VKS-OC 12 Part Kit 2.2 mm

2 matrices OC red 2.2

2 matrices OC yellow 2.2

2 matrices OC green 2.2

2 blocking out discs 2.2

1 insertion pin VKS 2.2

1 paralleling mandrel VKS 2.2

2 patrices OC 2.2

12 Part Kit 2.2 mm #430 053 10

$130.00

VKS-OC 10 Part Kit 2.2 mm




2 patrices OC 2.2


10 Part Kit 2.2 mm #430 053 40

$69.50

VKS-OC Universal 14 Part Kit

2 matrices OC red

2 matrices OC yellow

2 UNI patrices

2 blocking out discs

2 matrices OC green 1 press-in pin VKS

2 metal matrices 1 paralleling mandrel VKS

14 Part Kit 2.2 mm #430 053 20

14 Part Kit 1.7 mm #430 067 40

$159.00

$159.00

VKS-OC Universal 10 Part Kit

2 matrices OC red


2 matrices OC green

2 UNI patrices


10 Part Kit 2.2 mm #430 053 50

10 Part Kit 1.7 mm #430 067 20

$69.50

$69.50

VKS-OC Root Caps Uni Kit

2 matrices OC red


2 UNI patrices


2 matrices OC green 2 metal matrices

Root Cap Kit 2.2 mm #430 055 20

Root Cap Kit 1.7 mm #430 067 80

$105.00

$105.00

VKS-OC 3 Part Matrix Kit

1 matrix OC red

1 matrix OC yellow

3 Part Kit 2.2 mm #S15350

3 Part Kit 1.7 mm #S16720

1 matrix OC green

$29.00

$29.00

Instructions

VKS-OC

Instructions for Root Caps

VKS-SG/OC 2.2mm Introductory Kit




2 matrices OC metal 2.2

2 matrices SG red 2.2

2 matrices SG yellow 2.2


2 patrices OC 2.2

2 patrices SG 2.2

2 patrices UNI 2.2


1 each wax bars 1.6/1.9/2.2



2.2mm Introductory Kit #430 053 00

$267.00

VKS-OC/SG 1.7mm Introductory Kit




2 matrices OC metal 1.7

2 matrices SG red 1.7

2 patrices SG 1.7

2 patrices UNI 1.7

2 matrices SG yellow 1.7



1 each wax bars 1.6/1.9/2.2



1.7 mm Introductory Kit #430 065 10

$242.00

VKS-OC 30°+60° 22 Part Kit 1.7mm





2 OC 30° patrices 1.7

2 OC 60° patrices 1.7

1 press-in pin VKS 1.7


22 Part 30°+60° Kit 1.7 mm #430 073 49

$183.00

VKS-OC 30° 12 Part Kit 1.7mm

2 matrices OC red


2 30° patrices



VKS-OC 30° 12 Part Kit 1.7 mm #SA7345 $106.00

VKS-OC 60° 12 Part Kit 1.7mm

2 matrices OC red


2 60° patrices



VKS-OC 60° 12 Part Kit 1.7 mm #SA7347 $106.00

VKS-OC 6 Part Matrix Kit

2 matrices OC red


6 Part Kit 2.2 mm #S25350

6 Part Kit 1.7 mm #S26720

2 matrices OC green

$46.00

$46.00

The OC attachment is an excellent choice for custom root cap cases. The over denture case above requires two custom root caps with attachments on top.

The root cap posts are waxed up and the universal patrix is placed using the VKS Paralleling Mandrel.

When placed correctly, the patrix is attached by waxing around the cap.

This shows the final waxup of the root cap and the attachment. The entire waxup is cast in one piece. This gives the restoration greater strength while saving time and money.

After casting, finish the patrix by polishing lightly.

Overpolishing will cause the attachment to lose retention. The blocking out disc is then placed under the ball. The blocking out disc aids in blocking out and ensures the matrix sits parallel and stable on the patrix.

The yellow matrix is snapped into the metal housing using the insertion pin. It is recommended to use the yellow matrix with medium friction. For reduced and increased friction, use the green or red matrix respectively.

38

Prior to finishing, apply liquid silicone to the root cap or patrix. This will block out the undercuts and prevent acrylic from spreading underneath the attachment in the final restoration.

The metal housing with integrated plastic matrix is snapped onto the patrix, on top of the blocking out disc. This should be done while the silicone is still soft.

This is the finished denture viewed from the fitting surface. To change the matrix, the matrix must be destroyed with a round-head bur and pried out. A new matrix is snapped in using the insertion pin.

Instructions

VKS-OC Instructions for Distal Extensions.

The copings for the crowns are waxed up using standard techniques. It is recommended to double abut to give added strength for the OC patrix. It is also highly recommended to wax a lingual rest shelf for a lingual arm.

The OC patrix is waxed onto the copings with the

VKS Paralleling Mandrel. The use of a surveyor to parallel the patrices is necessary. The patrix should be placed as close to the tissue as possible to increase stability and minimize torque.

As seen above, the backing of the patrix can be reduced in height and length to allow optimum placement.

After casting and fitting on the model, polish the attachment lightly. If the attachment is not polished, residue and oxide may wear the matrices prematurely. The ball should not be ground upon or highly polished as it would lose retention and damage the attachment.

Place the blocking out disc under the ball and press the yellow matrix over it. The blocking out disc helps in the blocking out process and ensures that the matrix sits parallel on top of the ball.

To create the overcasting, the model needs to be duplicated with the yellow matrix in place.

Block out frame and the area between disc and the ridge. No wax should be on the matrix when it is duplicated.

The case is duplicated using silicone duplicating material. Above shows the refractory model of the case. The refractory model is a duplicate model made in investment. Notice the refractory “dummy” of the yellow matrix. It is important not to scratch or damage the refractory matrix or any of the areas that will be waxed over.

The chrome cobalt over frame is waxed as required.

Waxing over the refractory matrix will create the housing for the attachment matrices. A lingual arm should be incorporated into the framework for partials. Bredent retention beads or crystals could be placed on the wax framework to create a more retentive surface for the acrylic. The entire model

& wax-up is then invested.

The framework is cast and fitted. A light deplating of the chrome cobalt framework casting is usually required to clean and polish the interior of the attachment metal housing. If a higher electro-polish of the framework is required, it is necessary to block out the housing interior with a drop of wax to prevent over polishing. Over polishing could result in loss of friction.

Dimensions

To place the matrix into the framework, simply use the insertion pin and push the matrix into place.

No acrylic is required to hold the matrix in place.

To change the friction of the attachment, a small bur is used to tear the old matrix out of the housing and the new matrix is placed as usual.

This shows the finished frame with the yellow matrix inserted. No acrylic is needed to hold the matrix in place. The matrix is held in the framework by the undercuts on its sides.

The above picture shows the finished frame snapped onto the attachment. As with all attachments, the patients need to know that the appliance should not be inserted by biting into place - it needs to be inserted via hand pressure. Biting any attachment into place causes extreme forces that wear down the attachments prematurely.

2.2 mm

2.8 mm

2.0 mm

Example of a proper lingual arm

3.5 mm 3.1 mm

3.5 mm 3.15 mm

6.0 mm

4.6 mm

3.9 mm

4.4 mm

5.8 mm

1.7 mm 30 o

Patrix with

OC Metal Housing

6.2 mm

1.7 mm 60 o

Patrix with

OC Metal Housing

3.5 mm

2.2 mm Matrix

5.7 mm

4.3 mm

7.9 mm

2.2

OC Patrix with

Metal Housing

8.0 mm

2.5 mm

1.7 mm Matrix

4.7 mm

6.9 mm

2.2 mm OC Patrix

8.0 mm

3.0 mm

0.7 mm

3.0 mm


4.2 mm

4.3 mm

3.0 mm

2.2 mm Universal Patrix with Metal Housing

1.7 mm

2.1 mm

0.4 mm

2.1 mm


3.5 mm

3.5 mm

2.1 mm

1.7 mm Universal Patrix with Metal Housing

39

Made from

Grade 5 Titanium

VKS-OC RS Implant Abutments

VKS attachment abutments for Branemark, 3i, Steri-Oss Hex-Lock and Replace implants.

The VKS-OC RS Implant Abutments can be used on implants that are up to

15º divergent from the path of insertion. The abutments are available in

3 diameters, each with 3 different tissue heights. These abutments can be used with either the rigid or resilient matrices.

Dentist implant abutments and impression matrices

VKS-OC RS 4x2 Abutment 2.2mm

4 mm Ø, 2 mm tissue height

1 abutment + 1 impression matrix

#460 000 42 $76.50




#460 000 52 $76.50

Ø = Diameter




#460 000 62 $76.50




#460 000 44

$76.50




#460 000 54 $76.50




#460 000 64 $76.50




#460 000 46 $76.50

Laboratory implant analogs

VKS-OC RS 4mm Ø

Laboratory Analog 2.2mm

2 pieces

#460 000 04 $40.00


VKS-OC RS Latch

Screwdriver

#460 000 10

$44.00




#460 000 56 $76.50



2 pieces

#460 000 05 $40.00

VKS-OC RS Hand Screwdriver

#460 000 11 $39.50

VKS-OC RS Angle Guide

#460 001 00 $39.50




#460 000 66 $76.50



2 pieces

#460 000 06 $40.00

VKS-OC RS Vertical

Alignment Post

2 pieces #460 001 02

8 pieces #460 001 08

$41.50

$152.00

After uncovering the implant, a OC-RS abutment with the correct collar-height is screwed onto the implant with an OC-RS screwdriver with

30Ncm torque.

The abutments are available in 2, 4 or 6 mm collar-height. The impression matrices are placed on the abutments and are picked up into the impression.

After the impression is made with the impression matrices in place, the laboratory analogs with the correct diameters are inserted into the impression matrices.

40

Once the model has been poured with the laboratory analogs, the next step is to determine whether the implants are within acceptable angle tolerances for this attachment.

In the VKS-OC RS system, a tolerance of 15º per implant is acceptable. To determine the degree of the implant, the Vertical Alignment Post is first placed on the analog.

The 15º Angle Guide is used to determine if the implant is within the acceptable angle tolerances.

In a multiple implant situation, no implant can deviate more than 15º.

VKS-OC RS Matrix System

The VKS-OC RS 2.2 mm Matrices are available in rigid form. The matrices are easy to replace and can be done chairside.

or

These attachment matrices can be used either on the VKS-OC RS Implant

Abutments or on the VKS Universal patrices.

VKS-OC RS

Rigid Matrix Green 2.2 mm for low snap-in friction.

8 pieces #440 007 08

4 pieces #S40708

VKS-OC RS

Rigid Matrix Yellow 2.2 mm for normal snap-in friction.

8 pieces #440 008 08

4 pieces #S40808

VKS-OC RS

Rigid Matrix Red 2.2 mm for high snap-in friction.

8 pieces #440 009 08

4 pieces #S40908

VKS-OC RS

Titanium Housing

2 pieces #440 002 02

8 pieces #440 002 08


$52.50

$33.25

$52.50

$33.25

$52.50

$33.25

$69.50

$215.00

VKS-OC RS Paralleling Mandrel

For precise placement of the duplicating matrix & the housings.

#360 011 60

$86.00

Case

Designs

VKS-OC RS Implant Abutment • 1

VKS-OC RS Insertion Pin


#360 011 61

$22.50

VKS-OC RS 2.2 mm 4 piece set

OC RS Rigid Matrix: red, yellow, green

1 OC RS titanium housing

#SA0010 $58.50

VKS-OC RS Duplicating Matrix

8 pieces #440 011 08

4 pieces #S41108

$95.00

$56.95

VKS-OC RS Wax Matrix Housing

8 pieces #440 010 08

4 pieces #S41008

$52.50

$33.25

VKS-OC RS Blocking Out Disc

8 pieces #440 001 08

4 pieces #S40108

$52.50

$33.25

VKS-OC RS Matrix Pliers

Is used by technicians and dentists to remove the matrices from the housings.

#310 000 06

$130.00

VKS-OC RS Implant Abutment • 2

41

42

bredent

VKS-OC RS Implant Abutment Compatibility Chart

VSS

Vario Soft Bar

Indications:

• Implant Bars

• C & B Bars

The 2° taper simplifies fitting down, particularly if the removable section consists of chrome cobalt or other nonprecious alloy

VSS 2

o

• 2 o

bar system of implants and crowns & bridges.

• Three friction levels.

• Extremely secure and comfortable for the patient.

• Large contact area makes for improve stability.




A friction style attachment that can be adjusted in height to accommodate cases with limited occlusal space. Ideal for implant bar applications. Can be adjusted to adapt to the gingiva to prevent food impaction underneath. Can be combined with the VKS-SG if necessary to achieve optimal retention.

VSS Green Matrix

Retention Level 1

For low friction.

8 pieces #430 052 70

$52.50

The four rounded corners of the matrix produce guidance grooves to retain it securely in the removable section of the denture.

The snap retainers guarantee retention in the matrix housing.

VSS Patrix

Has smooth, parallel sides with a 2 degree taper.

8 pieces #430 052 40

$73.50

The bar patrix can be shortened along its base and mesial or distal surfaces as required

VSS Yellow Matrix



8 pieces #430 052 60

$52.50

VSS Red Matrix


8 pieces #430 052 50

$52.50

The external dimensions of the matrices are exactly the same which allows them to be interchanged with one another, depending on the desired level of friction.

Vario Soft Bar VSS Kit

2 matrices VSS red

2 matrices VSS yellow

2 matrices VSS green

VSS 9 part kit #430 052 30

2 patrices VSS

1 press in pin

$70.00

VSS Insertion Pin

Is used to insert the matrix into the framework.

2 piece package #430 073 63

$21.95

VSS Metal Housing

2 pieces #SA5270

$24.00

Made in

43

VSP-FS / VSP-GS

VSP-FS Friction Snap / VSP-GS Snap

This bar system not only offers you a choice of two types of matrices: Snap and Friction-Snap, but it also provides each in three different grip levels. Although the bar is the same for either, they are not interchangeable with each other. However, they can be used in combination with each other to achieve the perfect friction level required.

VSP-FS/GS Titanium Bar

For snap-in bar restorations.

1 piece #560 000 20

$120.00

VSP-FS Green Matrix


For low friction.

8 pieces #430 063 20

$52.50

VSP-FS Yellow Matrix



8 pieces #430 063 50

$52.50

VSP-FS Red Matrix


For high friction.

8 pieces #430 063 70 $52.50

VSP-FS Metal Housing


Made in

$24.00




Indications:

• C & B Bars

• Mesial / Distal of Implant Bars

• On top of Implant Bars

VSP-FS/GS Bar

For snap-in bar restorations.

4 pieces #430 069 40

$52.50

VSP-GS Green Matrix


For low friction.

8 pieces #430 062 70

VSP-GS Yellow Matrix



8 pieces #430 062 90

$52.50

$52.50

VSP-GS Red Matrix


For high friction.

8 pieces #430 063 10

$52.50

VSP-GS Metal Housing


Made in

$24.00

VSP Insertion Pin

For VSP-FS, VSP-GS

2 pieces #430 062 20

$21.95

Bar Mandrel

1 piece #430 062 30

$52.50

VSP-GS duplicating jig

Guarantees that the joint matrix grips optimally.

8 pieces #430 062 50

$52.50

VSP-FS Assortment Kit

4 matrices VSP-FS red

4 matrices VSP-FS yellow

4 matrices VSP-FS green

2 VSP-FS bars

1 insertion pin VSP

1 paralleling mandrel VSP

VSP-FS Assortment Kit #430 064 90 $148.95

Instructions

VSP-GS Assortment Kit

4 matrices VSP-GS red

4 matrices VSP-GS yellow

4 matrices VSP-GS green

2 VSP-GS bars

1 press-in pin VSP

1 paralleling mandrel VSP

4 VSP-GS duplicating jigs

VSP-GS Assortment Kit #430 064 80

$167.50

The bar should be fi tted between the implant abutments with a paralleling mandrel. The bar is made of rigid acrylic which can be trimmed easily and quickly.

After casting and trimming, the bar is secured on the abutments with the paralleling mandrel.

They should be soldered together to create a stress free unit.

Duplicating is carried out with the yellow matrix for the VSP-FS and with the Duplicating Jig for the

VSP-GS. This provides the optimum conditions for changing the degree of friction later.

The restoration is blocked out and duplicated using standard methods. No spacer wax should be applied around the matrix.

The matrix is also duplicated and acts as a spacer for the matrix housing in the chrome cobalt framework.

The bar and the matrix are simply coated with wax. The remaining sections of the patterns are waxed up as required.

44

Before inserting the matrix into its housing in the chrome cobalt framework, check the housing for bubbles and high spots.

The matrix with the desired degree of friction is selected and pressed in using the insertion tool.

The underside of the fi nished restoration with parallel bar and red matrix. The friction can be increased or decreased as required by replacing the matrix.

Security Lock Set Screw for Hybrid Overdentures

Initial tooth set-up.

A silicone matrix taken of the set-up relates the working spaces on the master model to wax the abutments.

Six abutments are waxed and pre-milled with a 2º taper.

Using a Diatit Multidrill (#33000790), a

1.4 mm pilot hole for the Security Lock is pre-drilled in plastic/wax.

The abutments are cast, finished and milled in preparation for the overcasting fabrication.

Pikuplast pattern resin (Yellow # 54000217) is used to create the overcasting. The

Auxiliary Modeling Element (# 36001169) was used to create a receptacle that allows bonding-in of the security lock assembly...

... and perforations were made into the connector areas of the overcasting for retention.

The silicone matrix is applied over the

Pikuplast resin overcasting pattern to check space availability.

Mesh pattern is added for extra retention.

The overcasting pattern is sprued according to The Bredent Casting Technique Manual

(# 992961GB).

A dense...

...and accurate casting.

After sandblasting the framework, the light curing, Tooth-Colored Opaquer UV

(# 54000105) is used to mask out the grey metallic color.

The teeth set-up is transferred onto the overcasting.

The case is finished using composite, however conventional denture acrylics may also be used.

A gingival-side view of the case. Pink colored composite was used to add some interdental papilla for maximum aesthetics.

The Security Lock is bonded into the preestablished receptacle using DTK Adhesive

(#54000106).

A hands-on course for this technique is highly recommended; call us at

877-328-3965

for pricing and availability.

The Security Lock locking screw is check for easy insert and removal.

45

NEW!

Friction Splint FS1

Connecting elements for superstructures

• Uncomplicated integration in the mouth

• Defective screw connectors can be repaired with FS1

• FS1 is replaceable

• Time-saving, no tapping necessary

• Variable application for all indications

• Can be individually shortened

• No loosening caused by expansion

The FS1 sleeve is placed through the splint hole

(identical size and position in both the primary and secondary units) with the splint screw being preassembled.

After pressing in the sleeve...

...the splint screw is turned in.

46

No tapping is necessary.

Wax-up silicone matrix.

Remove the wax-up. The pin hole is drilled into the abutment with the

Diatit-Multidrill Ø 2.0mm.

The wax-up is placed back onto the model. The modelling aid is integrated in the wax-up. Holes with a diameter of 2.0mm are drilled into the full wax-up at the positions for the attachments.

The attachments are milled. The previously prepared matrix serves for orientation. The ceramic spacer can be used to ensure perfect casting of the splint holes.

Using the modelling aids...

...the secondary units are waxed up and prepared for casting.

Sleeve...

...and splint screw are shortened to the same length if required.

In the case of zirconium crowns, it must be insured that...

...the diameter of the drillhole is

2.0mm after the sintering process and...

...the ceramic fi rings. Stress/tension within the ceramic can only be avoided this way.

The splint screw which is screwed halfway into the sleeve is positioned using tweezers.

...and pressed in. The remaining section of the splint screw is turned in.

The screwed-in fi xing screw is removed from the sleeve.

In case of usage of less than 1 year and in undamaged condition, the removed sleeve can be reinserted.

Friction Splint FS1 Sleeve

1 piece #450 000 80

$28.50

Friction Splint FS1 Pin

1 piece #450 000 81

$28.50

Friction Splint Spacer 2.0mm

2 pieces #450 000 82

$17.95

Modeling Aid Ø 2.0 mm

2 pieces #450 000 83

$21.50

47

Security Lock

Security Lock

Loosening of the screw is avoided in this system due to the engagement of the smooth section of the bolt into the substructure and the threaded section into the over-structure. This patented design allows micro-movements between the sub- and over-structure, thus avoiding the shear stresses that can cause the screws on other systems to loosen. Extremely easy to use and perfect for implants.

Security Lock 9 Piece Kit

2 Casting Screws 2 Sleeves

2 Locking Screws 1 Short Screwdriver

1 Center Drill 1 Diatit Multidrill

1.0 mm Kit #430 072 90

1.4 mm Kit #430 072 91

1.8 mm Kit #430 072 92

$345.00

$345.00

$345.00

The different sizes can be used for a wide range of applications with implants and bridges.

Invented by Peter Kuch

During three years of clinical experience with 268 patients, no screws loosened.

Once the abutment has been cast, it should be milled and polished.

A centering drill is used to create a dimple in the correct position.

The correct size of Multidrill is used to drill a hole at the correct angle for the threaded rod.

It is essential that Bredent’s milling and drilling oil (#550 000 08) is used.

Screw the threaded rod into the sleeve. Both the pin and the hexagonal socket can be reduced as required.

Coat the threaded rod and sleeve with Pi-Ku-

Plast resin (#540 002 20).

Pi-Ku-Plast guarantees optimum strength for continued processing.

Casting Screws with Sleeves

Screw a retention screw coated with colloidal graphite into the threaded sleeve to retain it in the investment material (#540 007 06).

Locking Screws (2 pcs)

$178.00 ea.

1.0 mm #430 072 96 1.4 mm #430 072 97 1.8 mm #430 072 98

Center Drill

$88.50 ea.

1.0 mm #430 072 93 1.4 mm #430 072 94

1.8 mm #430 072 95

Diatit Multidrill

The rear of the short screwdriver can be used to remove the retention screw.

Indications:


• C & B Bars


• On side of Implant Bars

• For Implant Abutments

• Screws & Pins

$39.50 ea.

$44.50 ea.

1.0 mm #330 008 15

Accessories

1.4 mm #330 006 60 1.8 mm #330 006 60 1.0 mm #330 006 10 1.4 mm #330 007 90

Colloidal Graphite

It is recommended to coat the threads with Colloidal Graphite before investing and casting the fixation screws.

#540 007 06

$45.50

1.8 mm #330 008 00

48

Milling and Drilling Oil

#550 000 08

$25.50

Replacement Screw 1.4

#S07294-G $42.00

Made in

Tap for 1.4 mm Screw (Cast-in)

(Specifically for gold sleeve)

#S07293-G $32.95

Security Lock 1.4

The adhesive type of security lock system is perfectly suitable for situations diffi cult to access such as small jaws or large span bridges. The titanium threaded sleeve that can be cemented in allows processing independent of the alloys.

Auxiliary Modeling Element 1.4

#360 011 69

$20.50

Locking Screw 1.4

#S07294-T

$42.00

Titanium Sleeve

#S07397

$19.95


Can be used with the security lock and the occlusal screw system.

#330 006 90

$33.95

Made in

Tap for 1.4 mm Screw (Bond-in only)

(Specifi cally for titanium sleeve)

#S07293-T

$32.95

Accessories

Locking Screw 1.4 mm &

Titanium Sleeve

(1 of each)

#S27294

$59.95

2 Locking Screws 1.4 mm

2 Titanium Sleeves

2 Analogs (Auxiliary Modeling Element)

#S67294

$150.00

NEW!



Center Drill

#330 006 60

$39.50

Pi-Ku-Plast HP36 Asst. Kit

$189.00

100 ml Monomer

100 ml Cleaner

85 g Polymer

1 Brush size A

1 Brush size B

1 Brush holder

3 Vessels

Blue Kit

Red Kit

Transparent Kit

#540 002 19

Yellow Kit

Orange Kit

#540 002 17

#540 002 18

#540 002 20

#540 002 16


#540 001 06

$125.00

(See page 51)


#330 007 90

$44.50


#550 000 08 $25.50

Made in

Tap Holder

#S07340 $26.50

49

Security Lock Instructions

Bond-in Technique

Implant bars or custom abutments are milled and polished.

Access hole is drilled using the 1.4 mm center drill and multidrill. Milling oil is recommended.

Auxiliary modelling pins are placed and checked for ideal positioning.

The angle in which the modelling element is placed will determine the angle in which the dentist will access the screw head.

Relief was is added to block out all gross undercuts in a parallel manner. A light coat of Vaseline on the bar is recommended.

Pi-Ku-Plast is used to create the overcasting pattern. Any color Pi-Ku-Plast can be used.

The bridge is waxed in the usual manner over the Pi-Ku-Plast patterns.

Upon removal of the auxiliary waxing pin, a uniform housing in Pi-Ku-Plast is achieved for bonding in of the screw and thread-sleeve.

Metal is fi nished and prepared for porcelain.

You must fi nish the porcelain work prior to bonding in the locking screw.

Careful investing ensures that the cylindrical housing is accurately replicated.

Locking screws and thread-sleeves.

A light coat of Vaseline is applied to prevent permanent bonding in of the locking screw.

Bonding cement is applied into the cylindrical metal housing.

Thread-sleeve and locking screw are inserted into the housing. Be sure to insert the screw all the way into the hole.

The locking screw is adjusted. Care must be taken not to over adjust the screw head as the hex can be lost and render the screwdriver useless.

Close up view of a properly adjusted locking screw.

You must fi nish the porcelain work prior to bonding in the locking screw.

50

Locking Pin

Locking Pin Snap System

> Excellent for implant cases.

> Easy for patients to insert and remove their prosthesis.

> Stable and reliable retention.

> Can be easily repaired by just inserting a new plunger.

Indications:

•

C & B Unilateral

• On Side of Implant Bars

• For Implant Abutments

• Screws & Pins

The soft, resin-supported guidance results in a soft snap of the locking pin during locking in the open or closed position. The snap informs the patient that the lock is completely open and the denture can be removed.

Locking Pin Snap in Open position Locking Pin Snap in Closed position

Locking Pin Snap E : for bonding in metal and resin

Locking Pin Snap E

1 piece #440 006 58

$67.00


Cast-in Integration Kit


Ceramic Spacer

2 pieces #440 006 57

$55.50

2 Locking Pin Snap E

2 Locking Pin Snap E ceramic spacers

1 Locking Pin Snap E waxing aid

#440 006 53

$

235.00


Waxing Pin

1 piece #440 006 56

$20.50


Resin Integration Kit


1 Locking Pin Snap E waxing aid

#440 006 51

$


Plunger

1 piece #440 006 59

$49.95

198.00

FGP Insulating

Liquid

#540 010 27

$48.00


Bond-In Kit


2 Locking Pin Snap E waxing pins

#440 006 52

$

143.00

Tools & accessories

Diatit Center Drill

#330 006 60

$39.50

NEW!


A dual hardening composite adhesive for the fixation of dental attachments.


1.5mm

#330 007 30

$44.50

Pi-ku-plast Resin HP

100ml kit #540 002 18

$189.00

Assortment Includes:

• 1 Base paste B, 5 g

• 1 Catalyst paste K, 5 g

• 1 Mixing block

• 1 Spatula

• 10 Application cannulas

(black)


20ml bottle #550 000 08

$25.50


$125.00

51

Locking Pin Instructions

A small dimple is prepared with the Diatit Center

Drill (#330 006 60) to determine the position of the drill hole. The dimple will center the drill and keep it in position.

The hole is drilled with the 1.5mm Diatit Multidrill

(#330 007 30). The dimple is used to guide the drill into position.

The waxing pins are inserted into the holes to check for proper positioning.

Gross undercuts are relieved using wax and is carved in a parallel manner.

Waxing pins are reinserted into the holes and the bar and pins are lightly coated with petroleum jelly.

Pi-Ku-Plast is applied over the blocked out bar and waxing pins.

After setting, the Pi-Ku-Plast pattern is gently lifted off and slightly adjusted with the use of burs or rubber wheels.

After adjusting, and removal of attachment components, the pattern is placed over the bar to check the fit. It is recommended at this time to add some mechanical retentions such as wax mesh, flat side up.

Additionally, some retentive “tails” can also be added.

The pattern is lifted off, sprued, and invested.

The casting is devested and carefully fit over the bar. It should have a frictive fit without the attachments in place.

Once the overcasting is seated, the hole in the bar should be clearly visible through the housing created by the Pi-Ku-Plast around the Waxing Pin

Ropak UV opaquer (#520 001 64 & 520 001 65) is used to mask out the metals color.

Denture teeth are arranged in a typical manner.

The denture is waxed. Acrylic processing is carried out in the usual manner and bonding in of the locking pin is done after finishing and polishing of the prosthesis.

A light coat of petroleum jelly is added to the non-bonding elements of the attachment.

Bonding cement is mixed and applied into the cylindrical metal housings.

The locking pin is then inserted into the chrome cobalt framework.

After the bonding cement has set, the locking pin attachments are checked for accurate fit and function.

Tissue side view of the locking pin cylinder in the closed position.

52

Occlusal Screw

Occlusal Screw System OC

Long Screwdriver


#330 008 12 $42.50



#330 006 90 $33.95

The paralleling mandrel positions the sectioning attachment correctly.

The design and small size of the threaded sleeve in the sectioning attachment allows it to be adapted to the papillae as required.

> Suitable for splinting non-parallel abutment teeth.

> Pre-made, cast-on thread sleeve can be used with

any gold alloy.

Latch Driver


#330 008 13 $31.50

Titanium Screw

1.4 x 2 mm

#330 007 00 $24.50


It is recommended to coat the threads with Colloidal Graphite before investing and casting the fixation screws.

#540 007 06

$45.50

OC Spacer Ring

2 pieces #430 073 04

$93.50

The threaded sleeve is made of a cast-on alloy and can be used with any gold or semiprecious alloy.

OC Occlusal

System Patrix

2 pieces #430 073 03

$113.00

The retention rod should be coated with colloidal graphite which retains the threaded sleeve precisely in the investment material.

With a diameter of 1 mm., the section that connects the attachment to the coping can be trimmed with a 1 mm. rotary cutter if required.

Indications:


• C & B Bars

• Screws & Pins

Casting Screw

2 pieces #360 010 30

$28.50

The circumferential ledge on the locking ring marks the level to which the locking ring can be reduced.

Paralleling Mandrel

#360 011 57

$53.00

To ensure that the locking ring is fixed in place, the outer section must be molded with Pi-ku-Plast brush on resin.

The exterior design of the locking ring, which consists of a cast-on gold alloy, ensures that it is retained securely in the resin.

The bridge pattern is waxed up onto the outer resin section.

The titanium screw can be ground to blend it into the occlusal surface.

53

Interlock

Interlock

Parallel and 2

o

Interlock - made of special wax with a high melting point.

Biotec Milling Wax is recommended as it is designed to mill cleanly without melting. See the wax section for more information.

• Fast and secure attaching of the Interlocks

• No damage of the die with the drilling of the Interlocks

• Defi ned wall strength of only 0.4 mm

Indications:



Parallel Interlock

8 pieces

#430 073 69

$28.00

Parallel Interlock Mandrel

1 piece

#360 011 66

$19.00

2 o

Interlock

8 pieces

#430 073 68

$28.00

2 o

Interlock Mandrel

1 piece

#360 011 65

$19.00

NEW!

VS-3 Mini Tapered

Bridge sectioning attachment for fi xed prosthesis in case of divergent abutment teeth

• Precisely fi tting, full burn-out synthetic mold parts.

• Conic shape for easy processing

• Integrated parallel holder on male parts and matrix

save time and expand the application range

• Designed for intra- and extra-oral use

• No individual milling work necessary

• Primary and secondary parts are fabricated

simultaneously to save time and money

The modellation is made according to insertion direction and esthetic requirements.

Female and male parts are assembled and the parallel holder is taken off the unrequired parts.

The existing retention and the height of the attachment are individually adjusted to the situation with a metal bur.

The secondary part is completed by the modellation of the bridge link.

By individualizing the attachment, it adapts to any situation perfectly.

Simply use a fi nger or an instrument to remove the parallel holder at the

“predetermined breaking point.”

Primary and secondary parts are modelled in one step; time-saving, material-saving, effi cient.

The modellation is mounted and the invested according to the Bredent

Casting Technique in one step.

Following casting, the attachment is blast-polished with 50 μm pearls.

The attachment is now assembled without having to work it over elaborately.

Female and male parts are simply exchanged for intra- or extra-coronal use. Any application is possible!

The attachment distinguishes itself through a special shape and precise fi t. The long-lasting connection is proof of success.

The integrated parallel holder allows intracoronal use of the female within the primary part.

VS-3 Mini Tapered conical bridge attachments

4 females, 4 males

#430 073 40

$63.50

54


Diatit Multidrill - 1.4 & 1.6 mm

Drills exact holes, even in hard chrome cobalt alloys.

As a result of the Diatit wear protection, this three-edged Multidrill has a device hardness of 3700 HV.

> A diatit “twist” drill bit that can be used for drilling holes

in hard alloys such as Chrome-Cobalt.

> To ensure a smoth drilling process (no stopping and thus

no tilting) and a long service life of the drills, a rich quantity

of oil must be used during each working process.

> We recommend that you use the Milling & Drilling Oil

(Item# 550 000 08).

This tool set can be used to position the screwed connector wherever required and according to the available space.

Diatit-Multidrill, 0.8 Ø x 8 mm



Diatit-Multidrill, 1.2 Ø x 2.3 mm


Diatit-Multidrill, 1.3 Ø x 3.2 mm






Diatit First Tap 1.4 mm

Diatit Last Tap 1.4 mm

Diatit First Tap 1.6 mm

Diatit Last Tap 1.6 mm

Diatit Tap Holder

Tungsten Carbide Center Drill

Tungsten Carbide Facing Cutter 1.2 mm

Tungsten Carbide Facing Cutter 1.3 mm


Titanium Screw 1.4 x 2.0 mm

Titanium Screw 1.6 x 2.5 mm

330 007 40

330 006 10

330 006 20

330 007 50

330 006 30

330 011 58

330 011 57

330 007 90

330 007 30

330 008 00

330 007 20

330 006 71

330 006 70

330 011 6V

330 011 6F

330 006 80

330 006 60

330 006 50

330 011 59

330 006 90

330 007 00

330 011 60

$44.50

$44.50

$44.50

$78.00

$78.00

$83.00

$83.00

$23.95

$44.50

$44.50

$44.50

$44.50

$44.50

$44.50

$44.50

$44.50

$39.95

$39.95

$53.50

$33.95

$24.50

$24.50

The hole can be drilled through the matrix into the patrix freehand, using a handpiece, or with a milling machine.

The conical recess for the screw head is created with the facing cutter when the primary and secondary parts are assembled.

The titanium screw held by the screwdriver can also be screwed in without difficulty in inaccessible places in the mouth.

Tool set for fabricating custom screwed connectors

1 Diatit-Multidrill, 2.3 mm long

1 Diatit-Multidrill, 5 mm long

1 M V first tap

1 M F last tap

1 Tap holder

1 Tungsten carbide center drill 1.4 mm Ø

1 Tungsten carbide facing cutter 1.2 mm Ø

1 Screwdriver

2 Titanium screws, M

1.4 mm 10 piece set #330 006 00 $368.00

1.6 mm 10 piece set #330 000 16 $415.00

The center drill is used to drill a dimple where the screw is to be placed.

Finish-drill the core hole in the primary part with the multidrill with depth gauge to the limit stop.

A thread is cut into the primary part with the first tap and the last tap.

The head of the screw can be adapted to the anatomy.

55

56

Attachment

Dimensions

Abutments

Product

VKS-OC RS Ø 2.2 mm

Vario-Kugel-Snap VKS-OC

Product

Patrix VKS-OC

Patrix VKS-OC uni/HL

Matrix housing for fixation in acrylics VKS-OC RS 2.2

Matrix housing for bonding VKS-OC RS 2.2

Duplicating matrix VKS-OC RS 2.2

Metal matrix housing VKS-OC 1.7

Metal matrix housing VKS-OC 2.2

Titanium matrix housing VKS-OC 2.2

Matrices, rigid VKS-OC RS 2.2

Matrices VKS-OC 1.7

Matrices VKS-OC 2.2

Blocking out disc VKS-OC 1.7

Blocking out disc VKS-OC 2.2

Blocking out disc VKS-OC RS 2.2

Item#

430 073 45

430 073 47

430 053 90

430 067 60

430 053 80

440 002 02

440 002 02

440 011 08

430 066 10

430 054 70

440 002 02

440 007 08

440 008 08

440 009 08

430 065 50

430 065 90

430 065 60

430 054 40

430 054 50

430 054 60

430 065 20

S05400

440 001 08

Item#

460 000 42

460 000 44

460 000 46

460 000 52

460 000 54

460 000 56

460 000 62

460 000 64

460 000 66

Thread

M2 x 0.4

M2 x 0.4

M2 x 0.4

M2 x 0.4

M2 x 0.4

M2 x 0.4

M2 x 0.4

M2 x 0.4

M2 x 0.4

Ø

Stud 1.7 mm

Stud 1.7 mm

Stud 2.2 mm

Stud 1.7 mm

Stud 2.2 mm

-

2.7 mm

2.7 mm

2.7 mm

3.3 mm

3.3 mm

3.3 mm

2.8 mm

3.5 mm

4.4 mm

-

4.4 mm

3.5 mm

4.3 mm

4.3 mm

3.3 mm

3.3 mm

3.3 mm

Tissue height

2 mm

4 mm

6 mm

2 mm

4 mm

6 mm

2 mm

4 mm

6 mm

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

Angle

-

-

30°

60°

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

Length

-

-

5.8 mm

6.6 mm

6.7 mm

Width

4 mm

4 mm

4 mm

5 mm

5 mm

5 mm

6 mm

6 mm

6 mm

Ø Stud

2.2 mm

2.2 mm

2.2 mm

2.2 mm

2.2 mm

2.2 mm

2.2 mm

2.2 mm

2.2 mm

40

40

40

40

Page

40

40

40

40

40

Height

3.9 mm

6.6 mm

7.5 mm

2.2 mm

3.2 mm

Page

35

35

35

35

35

- 41

-

3.4 mm

2.3 mm

3.1 mm

3.1 mm

3.0 mm

3.0 mm

3.0 mm

2.0 mm

2.0 mm

2.0 mm

2.7 mm

2.7 mm

2.7 mm

0.4 mm

0.4 mm

35

35

35

35

0.75 mm 41

35

35

35

35

41

41

41

41

41

41

35

35

Vario-Stud-Snap VKS-SG / OC exchangeable stud

Product

Stud-head screw VKS-SG/OC 1.7

Stud-head screw VKS-SG/OC 2.2

Thread sleeve VKS-OC 1.7

Thread sleeve VKS-OC 2.2

Thread sleeve VKS-SG 1.7

Thread sleeve VKS-SG 2.2

Item#

450 0005 6

450 0004 7

450 0005 4

450 0004 6

450 0005 9

450 0005 2

Drill-N-Tap Retrievable Ball Screw

Product Item#

Drill-N-Tap retrievable ball screw S27000

Ø

Stud 1.7 mm

Stud 2.2 mm

3.4 mm

3.4 mm

-

-

-

-

Depth

-

-

1.7 mm

1.7 mm

-

-

-

Thread

M 1.6 x 0.2

M 2 x 0.25

-

-

-

Width

-

-

3.0 mm

3.9 mm

Thread Sleeves Thread Diameter Ball Diameter Pilot Diameter

Stud 1.7 mm M2 x 0.4 2.2 mm 1.8 mm

Height

2.9 mm

3.5 mm

1.7 mm

1.7 mm

4.0 mm

5.1 mm

Page

31

37

26

26

Page

26, 37

26, 37

37

Attachment

Dimensions

Vario-Stud-Snap VKS-SG

Product

Patrix VKS-SG 1.7

Patrix VKS-SG 2.2

Patrix VKS-SG 1.7 sv

Matrix VKS-SG 1.7 Green

Yellow

Red

Item# Depth

430 067 00 2.7 mm

430 053 70 3.5 mm

430 073 53 4.3 mm

430 066 80 2.4 mm

430 066 60 2.4 mm

430 066 40 2.4 mm

Matrix VKS-SG 2.2 Green

Yellow

430 054 10 2.8 mm

430 054 20 2.8 mm

Red 430 054 30 2.8 mm

Castable SG Matrix Housings 1.7 S06 660 2.9 mm

(with tail: 11 mm)

Castable SG Matrix Housings 2.2

Metal SG Matrix Housings 1.7

Metal SG Matrix Housings 2.2

S05 420

SA6 680

SA5 410

3.3 mm

2.9 mm

3.3 mm

(with tail: 11.4 mm)

(with tail: 11 mm)

(with tail: 11.4 mm)

4.4 mm

4.4 mm

4.4 mm

4.5 mm

5.4 mm

4.5 mm

5.4 mm

Width

3.0 mm

3.8 mm

3.5 mm

3.3 mm

3.3 mm

3.3 mm

Interlock

Product

Interlock 2°

Interlock 0°

Item#

430 073 68

430 073 69

Ø

1.4 mm

0.9 mm

4.2 mm

4.2 mm

4.2 mm

3.8 mm

4.7 mm

3.8 mm

4.7 mm

Height

4.1 mm

5.4 mm

4.5 x 5.5 mm

3.0 mm

3.0 mm

3.0 mm

19

19

19

19

19

19

19

19

19

19

19

Page

19

19

Depth

-

-

Length

-

-

Width Height

1.0/1.4 mm 6.0 mm

2.2 mm 6.0 mm

Page

54

54

VS-3 Mini

Product

VS-3 Mini patrix

VS-3 Mini matrix

VS-3 Mini sv patrix

VS-3 Mini sv matrix

VS-3 Mini Metal Housing

Vario-Soft-Bar-Pattern VSP

Product

Bar, friction-snap / joint snap-in

Matrix, friction-snap

Matrix, joint snap-in

VSP-FS Metal Housing

VSP-GS Metal Housing

Item#

430 073 25

430 073 17

430 073 15

430 073 13

430 073 43

430 073 35

430 073 33

430 073 31

SA7 317

-

-

-

-

Ø

-

-

-

-

-

Depth

2.3 mm

2.0 mm

2.0 mm

2.0 mm

4.1 mm

2.0 mm

2.0 mm

2.0 mm

2.9 mm

(With tail:

10.4 mm)

Width

3.1 mm

3.0 mm

3.0 mm

3.0 mm

3.5 mm

2.6 mm

2.6 mm

2.6 mm

4.3 mm

Height

6.0 mm

6.0 mm

6.0 mm

6.0 mm

5.8 mm

6.0 mm

6.0 mm

6.0 mm

6.7 mm

Max.reduction Page

3.0 mm 15

3.0 mm 15

3.0 mm

3.0 mm

2.8 mm

2.8 mm

15

15

15

15

2.8 mm

2.8 mm

7.5 mm

15

15

15

Item#

430 069 40

430 063 20

430 062 70

SA6 320

SA6 270

Ø

-

-

-

-

-

Length

50 mm

5.6 mm

5.4 mm

5.6 mm

5.4 mm

Width

1.5 mm

3.1 mm

3.1 mm

4.5 mm

4.1 mm

Height

3.5 mm

4.2 mm

2.3 mm

4.4 mm

4.4 mm

Page

44

44

44

44

44

Vario-Soft-Bar VSS

Product

Bar, Patrix vss

Matrix vss

Item#

430 052 40

430 052 70

430 052 60

430 052 50

VSS Metal Housing SA5 270

-

-

-

Ø

-

-

Length

48 mm

6.7 mm

6.7 mm

6.7 mm

8.0 mm

Width

2.2 / 2°

3.4 mm

3.4 mm

3.4 mm

5.0 mm

Height

7.1 mm

8.0 mm

8.0 mm

8.0 mm

6.2 mm

43

43

43

Page

43

43

57

Attachment

Dimensions

Friction Splint FS1

Product

Friction Splint FS1 Sleeve

Friction Splint FS1 Pin

Friction Splint FS1 Spacer

Modeling Aid

Item# Ø

450 000 80 -

450 000 81 -

430 000 82 2.0 mm

450 000 83 2.0 mm

-

-

Length

-

-

-

-

Thread

-

-

-

-

Length/Rod Max.reduction Page

- - 47

- - 47

-

-

47

47

Locking Pin Snap System

Product

Locking pin Snap

Locking pin Snap sleeve

Security-Lock-System

Product

Threaded rod, Titanium 1.0



Matrix sleeve, Titanium

Matrix sleeve HL 1.0



Occlusal Screw System OC

Product

Titanium screw 1.4

OC spacer ring

OC occlusal system patrix

Item# Ø Axle

440 006 58 1.5 mm

440 006 60 2.8 mm

Item# Ø

330 007 00 2.1 mm

430 073 04 2.5 mm

430 073 03 3.0 mm

Ø Ring

3.5 mm

-

Item# Ø Length

430 072 93 rod 1.0 mm 8.5 mm

430 072 94 rod 1.4 mm 8.5 mm

430 072 95 rod 1.8 mm 8.5 mm

430 073 97 2.8 mm 5.3 mm

430 072 96 2.8 mm

430 072 97 2.8 mm

430 072 98 3.2 mm

5.3 mm

5.3 mm

5.3 mm

Length

4.5 mm

2.1 mm

6.9 mm

Length

6.25 mm

3.6 mm

Ø

-

2.8 mm

Max.reduction Page

- 51

- 51

Thread Length/Rod Max.reduction Page

M 2 / 0.4 3.5 mm 2.3 mm 48

M 2 / 0.4 3.5 mm 2.3 mm 48

-

-

M 2.5/0.45 3.5 mm

- -

-

-

-

-

2.3 mm

2.3 mm

2.3 mm

2.3 mm

2.3 mm

48

48

48

48

48

Thread Length/Head Max.reduction Page

M 1.4/0.3 2.5 mm 1.4 mm 53

- - 1.4 mm 53

M 1.4/0.3 - 3.3 mm 53

Diatit Tool Set M 1.4 / 1.6

Product

Titanium screw M 1.4

Titanium screw M 1.6

Item# Ø

330 007 00 2.1 mm

330 011 60 2.3 mm

Length

4.5 mm

5.2 mm

Thread Length/Head Max.reduction Page

M 1.4/0.3 2.5 mm 1.2 mm 55

M 1.6/0.35 2.5 mm 1.2 mm 55

58

CONTINUING EDUCATION COURSES

VKS-SG, VKS-OC and VS-3 Mini Attachment System Introductory

Course

How to Fabricate an Overcasting Over Existing Implant Bars

Course

Implant Bar Design and Advanced Attachment

Course

CALL FOR MORE INFORMATION & TO RESERVE YOUR SEAT!

1.877.328.3965

Exakto-Form

Model resin for accurate reproduction and maximum edge stability.

Exakto-Form Kit

(Includes components A+B)

Component A: 6x50g

Component B: 6x50g

Green #520 002 80 $85.50

Ivory #520 002 82 $85.50

Yellow #520 002 84 $85.50

Practical tip:

If a silicone impression is used with a polyurethane basis, the impressions must be previously sprayed out with Exakto-Form

Insulating Liquid (Order #520

002 10) to avoid bonding of the impression and model.

Exakto-Form Refill Packages

1x50g Component B #520 001 73

$9.95

Green 1x50g Component A #520 001 74

$9.95

Ivory 1x50g Component A #520 001 76

$9.95

Yellow 1xx50g Component A #520 001 78

$9.95

Exakto-Form Insulating Liquid

125 ml #520 002 10 $23.50

Prior to mixing, each component must be stirred so that a homogeneous mixture is obtained. Mix the sediment completely.

Add component A to component

B; empty tin completely.

Mix Exakto-Form approximately

30 seconds until a uniform color is obtained.

Two tins of Exakto-Form are sufficient to produce 2-3 complete dental arches.

The material can be removed after 30 minutes. Final hardness is achieved after 90 minutes. Then the model can be trimmed.

If a base for the model is to be produced with Exakto-Form, the model must first be insulated with

Exakto-Form Insulating Liquid.

Due to its high edge stability,

Exakto-form is perfectly suitable for precision-fit bridge and crown work.

Any technique can be used for sawing Exakto-Form models.

Adopting a new technique is not required.

If smaller quantities are used, fill component A and B into separate syringes.

Pour equal quantities of Exakto-

Form into a silicone beaker (approximately 2 ml for one die) and mix to obtain a homogeneous material. Please note, material in syringes must be used within

5 days.

Pour Exakto-Form into the impression. The excellent flow properties prevent the formation of bubbles even in impressions with thin edges.

The hardened resin can be drilled and trimmed. The stability avoids dimensional changes and guarantees precise models.

59

FGP Friction

FGP Friction Fit System

An absolutely tension free fit.

This friction fit system offers the dentist and the dental technician entirely new options for the preparation and restoration of telescopic and metal-metal situations. The long service life and the simple, time saving processing render this friction fit system a comfortable solution for the patient.

These advantages have contributed to more than 25,000 cases allowing soft integration and removal of the denture. The function of the FGP resin is that the metal on metal telescopic cases will now be replaced by a metal on resin fit. The metal on resin fit offers the benefit of a considerably more coefficient of friction than the one of a pure metal fit. Consequently, increased resistance to wear and an extended service life are obtained.

• Time saving due to fast and simple preparation

• Renovation of individual friction at reasonable costs

• No fitting of secondary elements

• Long service life

• Maximum comfort of wear for the patients

• Allows low cost, single piece castings

• Can be processed in the mouth

For this comparison between a classical metal fit and an FGP fit, 21,000 integration and removal processes were simulated. This corresponds to a wear period of approximately 20 years.

Conventional metal on metal fit FGP resin on metal fit

60

Metal fit after completion adjusted to a frictional force of eight Newtons.

Scanning electron microscope picture of the inner side of a telescopic secondary element made of a precious metal alloy with a magnification of 100.

Resin fit after completion adjusted to a frictional force of eight Newtons.

Scanning electron microscope picture of the inner side of a telescopic secondary element made of FGP resin with a magnification of 100.

Result: Residual friction of two

Newtons, that is only 25%

Result: Residual friction of six

Newtons, that is still 75%

FGP Friction Fit System

Metal to resin friction fi t.

FGP Friction Fit System Assortment

Friction Resin Component A 2.5 g.

Friction Resin Component B 2.5 g.

FGP Bonding Agent 1.25 ml.

FGP Insulating Agent 3.0 ml.

1 Spatula

5 Brushes

1 Brush holder

1 Mixing block

#540 010 28 $329.00

Refi ll Packs

Friction Resin Component A

Friction Resin Component B

FGP Bonding Agent

FGP Insulating Agent

#540 010 8A $85.50

#540 010 8B $85.50

#540 010 26

#540 010 27 $49.50

Accessories

Mixing Blocks

35 x 50 x 10 mm., 10 pieces

Disposable brush, 100 pieces

Brush holder, 12 pieces

#330 011 44

#330 011 42

#330 011 41

$49.00

$25.50

$25.50

Safety and outstanding quality

A direct solution rather than extended waiting times

The FGP system by bredent offers optimum and individual friction when preparing new conical and telescopic crowns.

The simple use during the restoration of the friction of telescopic work is the solution for the dentist and the patient.

The excellent sliding properties of FGP resin ensure gentle, implant protection integration and removal of the supra constructions.

Even very small tensions in the low cost and biocompatible, single piece casting process are perfectly compensated.

The high resistance to abrasion and nontilting integrating and removing of the supra construction provide the patient with a high comfort of wear and simple handling of the denture.

The friction with FGP resin that will remain stable over many years guarantees the patients’ happiness and satisfaction.

61

NEW!

Exaktosil N 21 Pouring Silicone

Pouring silicone for the duplication of models.

Components A and B are mixed in a 1:1 ratio. The components are stirred until they are evenly mixed.

Then power mix under vacuum for 30 seconds.

Exaktosil N 21

Duplicating Silicone Kit

1000 g component A

1000 g component B

#540 011 47

$150.00

Exaktosil N 21

Component A

1000 g

#540 011 6A

$84.00

Exaktosil N 21

Component B

1000 g

#540 011 6B

$84.00

The advantages of Exaktosil Duplicating Silicone:

• Excellent reproduction of detail

• High tear resistance

• Low shrinkage

Exaktosil Silicone features particularly low shrinkage and virtually bubble-free duplicating molds.

Model can be de-molded after 30 - 40 minutes.

Exaktosil consistent quality ensures precision accuracy when duplicating.

NEW!

Exaktosil C Kneading Silicone

Kneading Silicone for the production of matrices.

62

Exaktosil C

Kneading Silicone Kit

1250 g Base Material

50 g Hardener Paste

#540 010 29

$76.50

A measuring spoon of Exaktosil C kneading silicone is mixed with 3 cm of hardener paste.

Base Material

1250 g

#540 010 9A

$58.00

The components are kneaded until a uniform color is achieved.

Hardener Paste

50 g

#540 010 9B

$26.00

Exaktosil C kneading silicone has a soft consistency that allows accurate adaptation of even the most difficult to access areas.

The fine reproduction of details and high stability of Exaktosil C kneading silicone provides precise matrices that allow efficient processing.

NEW!

Multisil-Mask Soft

Accurate reproduction of gingival tissue.

Quick and economical processing with the cartridge and the specially adjusted silicone allow trouble-free direct application into the impression or the matrix. The natural color of the gingival mask supports perfect shade determination of the veneer. Overdimensioning of margins is recognized immediately.

Multisil-Mask Soft Kit

2 Cartridges 50 ml

24 Mixing Cannulas

1 Insulating Liquid 10ml

#540 010 41

$98.00

Multisil Separating Agent

10 ml insulating liquid

#520 010 03

$11.50

Mixing Canulas

12 pieces

#320 004 50

$21.95

Multisil-Mask Soft

Refill Cartridge

50 mL

#540 010 47

$29.50

The gingival situation on the unsawed sawcut model...

...is reproduced using Exaktosil

C kneading silicone and then the arch is sawed.

The sawcut are coated with wax.

Aesthetic

Efficient

Informative

Openings (inlet & outlet) are drilled into the matrix using the locating matrix drill and

Multi-Sep is applied.

The dispensing device with cartridge and canula is held to the opening. While applying the material from the dosing device, the matrix is fixed on the model...

...to obtain the correct position of the gingival mask.

Master-Pin System

Brass pin and plastic sleeve which has the smallest drilling depth of all pins of 4.5 mm.

Due to the special surface design of the inner wall of the sleeve, soft friction between the pin and sleeve is achieved while ensuring maximum precision and safety.

• Drill hole diameter of 1.5mm

• Drilling depth of only 4.5mm in the arch

• Boundary line for drilling at the Master-Pin for perfect drilling results

• Lateral flattening of the Master-Pin sleeve for pins with small distances to each other

• Defined soft friction between Master-Pin and Master-Pin sleeve

• Uniform height of model base, since the sleeves are longer than the Master-Pins

• Master-Pin Diatit tungsten carbide drill for constant, precise drilling over long periods

The correct height of the arch is essential.

This is the correct alignment of drillholes in the arch.

The arch as well as the Master-Pins are separated with Master-Sep

(520 002 90).

Even in the case when two pins are very close, the Master-Pin sleeve can still be used due to the lateral flattening.

( Continued on next page...)

63

Master-Pin System

The drillholes are positioned with the Master-Pin Diatit tungsten carbide drill (#360 011 92).

The arch is removed from the model base towards the pins.

The die segments are separated using a Gifl ex diamond disc.

Perfect fi t of the working dies on the model base.

Master Pin Assortment

200 Master-Pins

200 Master-Pin sleeves

1 Master-Pin Diatit tungsten

Ø 1.5/2.0mm, shaft Ø 3 mm carbide bur

1 working box #360 012 26

$132.00

Master-Pin Diatit tungsten carbide step drill

Ø 1.5/2.0mm, shaft Ø 3mm

1 piece #360 011 92

$36.50

Master-Sep

Insulating liquid - plaster against plaster

200 ml

#520 002 90

$37.50

Perfect results are obtained in conjunction with the Master-Pins.

Refi ll Package

1000 Master-Pins

1000 Master-Pin sleeves

#360 012 25 $222.00

Silicone & Wax surface tension reducing agent

Improves the fl ow characteristics of plaster on silicone impressions.

Silicone and wax surface tension reducing agent

750ml #540 007 05

$46.50

Empty Spray Bottle

125ml

#540 007 50

$6.50

The spraying head of the spray bottle simplifi es uniform wetting surface with silicone and wax tension reducing agent.

After the application of the agent onto the surface (above), the fl ow characteristics of the plaster have been clearly improved.

Plaster Separating Liquid

For reliable insulation of plaster against plaster.

Silicone and wax surface tension reducing agent produces a homogeneous plaster surface. This will ensure precise dental work.

Plaster Separating Liquid

750ml #540 001 35

$52.50

The plaster separating liquid soaks into the plaster and seals the surface without layering. The pen brush allows quick application.

The spray bottle insulates large areas within a short time. The fi ne spray mist ensures uniform wetting of the surface.

Empty Brush Pen Bottle

125ml #390 003 30

$18.50

Empty Spray Bottle

125ml

#540 007 50

$6.50

The gap-free fi t ensures maximum precision.

The plaster separating liquid allows separating of the base and the arch without any damage.

64

Isobre wax insulating liquid

Micro-fine insulating liquid on organic basis for reliable, exact separation of the wax pattern against all materials.

Isobre wax insulating liquid on organic basis is absolutely reliable, solvent-free and can be washed off easily. Neutral against plastic, ceramic, metal, plaster and painted surfaces.

Even when the insulated surface has dried, Isobre wax insulating liquid will produce a highly efficient, micro-fine insulating layer which ensures simple and safe removal of the wax pattern. Highly absorbing surfaces must be insulated 2 to 3 times.


750 ml

#540 010 40

$33.50

Empty Brush pen

20 ml

#540 007 20

$11.50

Gloss & Hardening agent for plasters

Gloss and hardening agent for plaster

100ml #550 000 02

$37.50

Without the hardening agent, models can be damaged when the restoration is placed on the model.

The special consistency leads to the diffusion into the plaster surface. The high edge stability and scratch resistance prevents most surface damage.

Plaster burnisher and hardener

20ml #550 000 01

$13.50

The gloss and hardening agent for plaster hardens after only 2 minutes.

Gloss and hardening agent for plaster diffuses into the plaster so that it can also be used on margins.

Transblock

Transparent block-out material for fast and purposeful working in all techniques.

Any desired size or shape of transblock can be produced with the help of an instrument or scissors.

Transblock

250 g

#540 011 49

$55.95

The high flexibility simplifies placing

Transblock onto the model.

Due to its stability, a uniform thickness is retained during the adaptation. If required, the thickness can be adapted individually by scraping.

The transparency of Transblock allows to check the thickness of the area that has been blocked out.

This way precisely prepared models for individual trays are obtained.

65

Diatit Cutting Tools

volume discounts

Diatit coated structure

Bredent’s tungsten carbide tools consist of a metal sintering material with a very fi ne grain size. Additionally, Diatit tools are subject to a hardening process after the cut has been completed. This hardening process reaches into the gaps between the crystals up to a depth of 100 µm.

Bur without Diatit coating

1850 HV

Hardness uncoated blade

Dulling of the cutting edges of the Diatit tools is reduced due to the wear protection.

Compared to uncoated carbide burs the hardness of the Diatit rises up to 3700 HV

(compared to 1850 HV) and results in an increased service life of the tool.

friction heat

Bur with Diatit coating

coated blade friction heat

The surface of the tool is smoothened so that the friction is reduced. The scraps come off the tools more easily. This results in smoother running of the tool.

66

Diatit tools feature the advanced Diatit wear protection coating. This is a special material which is added into the surface of the bur after it has been produced. It hardens the tool surface and reduces the surface friction. This comprehensive hardening process results in a tool which features very smooth rotation and precise cutting performance from the very beginning - and this is provided over a considerably long period. Accurate removal of material is ensured. Additionally, the service life of the tool (compared to uncoated carbide burs) is increased considerably by the hardening process.


KH: Cross cut with relief

Material Plaster

Speed

(rpm)

10-20,000

Denture

Acrylic

Composite

Precious

Metal

CrCo, Non-

Precious

10-20,000 10-20,000 10-20,000 10-20,000

Ceramic

15-20,000 with relief without relief

Conventional carbide bur machining angle.

Optimized machining angle. Wide support of edge for triple service life.

• For processing of precious metals, non-precious metals, resin and plaster

• Fine removal of material, very smooth surface of object, low vibration running protects the wrist of the technician

• Cross Cut Relief: wider, stable cutting edge for extended service life, enhanced cutting performance

D001 KH 23 $29.95

Smooth surface and fi ne cutting performance on hard materials.

KF: Cross cut fi ne

Material

Speed

(rpm)

Plaster

N/A

Denture

Acrylic

Composite

Precious

Metal

CrCo, Non-

Precious

12-18,000 15-20,000 15-20,000 15-20,000

Ceramic

15-20,000

• Mainly for more delicate types of work on precious and non-precious metals, resins and ceramics

• Moderate and accurate removal of material, smooth surface of object

D137 KF 23 $29.65

D184 KF 16 $25.50

Due to the fi ne cut a smooth surface of the object is obtained. This slender tool is particularly suitable for fi nishing veneers.

D187 KF 23 $31.00

D194 KF 23 $29.65

This bur is particularly suitable for fi nishing of ceramicmetal frames.

D194 KF 50 $38.50

The fi ne micrograph of the KF cut simplifi es polishing of the metal surface.

D198 KF 23 $26.90

The slender design and smooth micrograph of this bur ensure fine suitability for finishing of partial frameworks.

D200 KF 23 $31.00

D225 KF 23 $26.75

D237 KF 23 $25.00

Due to the fi ne cut a smooth surface can be produced on hard alloys as well.

D263 KF 40 $34.00

This bur can be used for a wide range of applications in the CrCo technique.

D289 KF 23 $23.90

The KF cut if perfectly suitable for fi nishing of metal ceramic veneers.

D292 KF 23 $29.65

67


KM: Cross cut medium

Material

Speed

(rpm)

Plaster

15-20,000

Denture

Acrylic

Composite

Precious

Metal

CrCo, Non-

Precious

15-18,000 15-20,000 15-20,000 15-20,000

Ceramic

15-20,000

• For finishing of larger surfaces on precious metals, non-precious metals, resins and plaster

• Efficient removal of material, smooth surface of object, smooth running of tool

• Universal application possibilities, therefore reduced frequency of tool exchange

D001 KM 23 $26.90

D137 KM 23 $26.90

D141 KM 23 $28.50

D194 KM 23 $28.50

D184 KM 16 $24.20

D194 KM 50 $36.90

D187 KM 23 $28.50

D198 KM 23 $23.90

D200 KM 23 $28.50

D225 KM 23 $23.90

D257 KM 23 $25.00

D237 KM 23 $23.90

This tool is particularly suitable for finishing CrCo frames.

D263 KM 40 $35.90

D277 KM 23 $23.90

D289 KM 23 $20.40

D257 KM 16 $35.00

D277 KM 14 $35.00

D292 KM 23 $26.90

KG: Cross cut coarse

Material

Speed

(rpm)

Plaster

10-15,000

Denture

Acrylic

Composite

Precious

Metal

CrCo, Non-

Precious

8-12,000 10-17,000 15-20,000 15-20,000

Ceramic

15-20,000

• For coarse and efficient pretreatment of large surfaces on precious metals, non-precious metals, resins and plaster

• Extensive removal of material, increased surface roughness than the finer bredent cut tools

D187 KG 23 $25.50

D001 KG 23 $25.00

Ideal for the removal of bubbles when fitting down crowns.

D194 KG 23 $25.50

D137 KG 23 $26.90

The slender design and the fine cutting performance of this tool makes it indispensable for use in finishing

CrCo.

D194 KG 40 $34.00

D194 KG 50 $39.50

D200 KG 23 $26.90

D274 KG 60 $39.50

D237 KG 65 $37.50

D263 KG 60 $39.50

Due to its shape and the coarse cut, the D263 KG 60 is well suited for trimming plaster dies.

D292 KG 23 $26.90

QM: Horizontal cut medium

Material Plaster

Speed

(rpm)

15-20,000

Denture

Acrylic

Composite

Precious

Metal

CrCo, Non-

Precious

15-28,000 15-20,000 15-20,000 15-20,000

Ceramic

15-20,000

68

• Suitable for finishing of larger surfaces as well as for more delicate work on precious and non-precious metals and resins

• Very fine, economic removal of material producing a smooth surface

• High running smoothness protects the motor and wrist

D137 QM 23 $23.90


KS: Cross Super Coarse

Material

Speed

(rpm)

Plaster

8-12,000

Denture

Acrylic

Composite

Precious

Metal

CrCo, Non-

Precious

8-12,000 N/A N/A N/A

Ceramic

N/A

• Especially for processing of plaster, also suitable for coarse types of work on resin

• Extensive removal of material

• The size of the individual cut space avoids loading with shavings

D194 KS 60 $40.00

D194 KS 70 $43.00

GG: Straight Cut Coarse

• To perform cuts in resin or shellack plates

• Very economic cutting of plates

• Single, straight cutting edges

D468 GG 16 $20.40

Material

Speed

(rpm)

Plaster

8-12,000

Denture

Acrylic

Composite

Precious

Metal

CrCo, Non-

Precious

8-12,000 N/A N/A N/A

Ceramic

N/A

D468 GG 23 $20.50

Power Cutting Burs for CoCr & Non Precious

KC: Cross Cut Chrome-Cobalt

Material Plaster

Denture

Acrylic

Composite

Precious

Metal

• Especially for processing of chrome-cobalt alloys

• Excellent removal of material, smooth surface

Speed

(rpm)

N/A N/A N/A N/A

• The resulting metal scraps cause fewer irritations to the skin since they are larger and exhibit a coarse structure

CrCo, Non-

Precious

10-20,000

Ceramic

N/A

D194 KC 40 $36.50

D251 KC 60 $42.00

D292 KC 23 $25.50

Designed strictly for quick Titanium finishing

KT: Cross Cut Titanium

• Especially for processing of titanium

• The special cut increases the cutting volume with reduced friction. Overheating of titanium is avoided

• Economic, careful removal of material, smooth surface

D001 KT 14 $23.00

10-15,000 rpm

D001 KT 23 $23.00

10-15,000 rpm

D194 KT 40 $31.00

20-25,000 rpm

D194 KT 50 $35.90

20,000 rpm

D263 KT 40 $34.00

20-25,000 rpm

D194 KT 23 $25.00

20-25,000 rpm

D198 KT 23 $26.90

25-30,000 rpm

69

Diatit and tungsten carbide burs for the handpiece

Rapid Microbur with a 3.1mm diameter suitable for exposing the preparation margins.

Application Field

Working Speed RPM

Tungsten Carbide

#H00 1NH 31

$19.25

Plaster Resin

10-20,000

Denture Resin

10-18,000

Veneer Resin Precious Metal CrCo/NPM

10-20,000 10-20,000

Ceramic

15-20,000 15-20,000

Application Field

Working Speed RPM

Diatit

#D19 4KF 40

$36.90

Plaster Resin

N/A

Denture Resin

12-18,000


15-20,000 15-20,000

Ceramic

15-20,000 15-20,000

70

Application Field

Working Speed RPM

Diatit

#D19 4KM 40

$36.90

Plaster Resin

15-20,000

Denture Resin

12-18,000


15-20,000 15-20,000

Ceramic

15-20,000 15-20,000

Universal bur with relief cut.

Application Field

Working Speed RPM


#H27 4GH 40

$45.50

Plaster Resin

10-20,000

Denture Resin

12-18,000


15-20,000 15-20,000

Ceramic

15-20,000 15-20,000

Bur with relief cut for quick removal of denture resin. Perfectly suitable for plaster.

Application Field

Working Speed RPM


#H26 3SH 60

$39.50

Plaster Resin

12-18,000

Denture Resin Veneer Resin Precious Metal CrCo/NPM

8-12,000 N/A N/A N/A

Ceramic

N/A

Friction Grip - Diabolo for all ceramic cores

Fast, efficient preparation of each type of Zirconia, Alumina Oxide and other hard tooth materials.

Diamond crystals are embedded into a special mixture of binding material.

Assortment

Includes 1 of each style

#330 011 66

$260.00

Round Tip

#FF 263 014

$51.95

Flame

#FF 250 016

$51.95

Rounded Cylinder

#FF 141 023

$46.50

Inverted Cone

#FF 227 023

$46.50

Carefully selected natural diamonds are entirely integrated into a mixture of metal and binding material. Due to the special manufacturing process, worn out diamond grit is automatically removed and replaced with new diamonds so that automatic sharpening is achieved. The auto sharpening effect enables it to perform highly difficult processing of dental material in a simple, fast, and efficient way.

Torpedo

#FF 289 023

$46.50

Diabolo-Cleaner

#340 010 00 $13.50

Friction Grip Adapter

#340 010 02 $7.50

Round Tip

#FF 263 023

$46.50

In the case of electro deposited grinding tools, the diamond crystals have been attached to the bur blank in a metal bond.

In the bredent sintering method, the razor sharp diamond crystals are embedded in an adapted mixture of binding material.

71

72

Bredent Milling Machine BF-2

Non-broken arm design for comfort and precision.

For milling, surveying and drilling. Can be locked in any position or used as a free-fl oating milling arm

The survey platform allows a vertical range of movement up to 90 degrees

Rigid construction made of aluminum and stainless chromium steel

Very smooth, vibration-free running; quick change for rapid bur exchanges

Micrometer control with depth stop and drilling gauge for ultra-precision

Precision guides ensure long service life

Ergonomic table raises to eye level

BF-2 Milling Unit

#140 008 92

*Call for more information: 1.877.328.3965

*Convenient financing with Priority Leasing, Inc.

Call to request a credit application today!

1.800.761.2118.

Exact drillholes due to bit stop

Precision guides ensure long service of life

Smooth, vibration-free running

Perfect lighting of the working area with the integrated halogen lamp

Rapid exchange of burs ensured by quick-stop

Model support locks in horizontal position, turning range of up to 90º

Fast and reliable model table chuck mechanism for precise working

Height-adjustable milling table

• Constant working and viewing

height

• Ergonomic design allows

nontiring working

Rigid construction made of highquality aluminum alloy and stainless chronium steel

Easy and precise height adjustment

Clearly-arranged control panel for quick access and speed selecting, clockwise/counterclockwise rotation and lighting

Stable plastic tray ensures clean working place during milling

Milling Unit BF-2

The milling unit that is simply perfect - even in its price/performance ratio.

Excellent milling of wax due to the adjustable speed control.

The Bredent polishing bur provides a high shine on metal surfaces.

Selecting a low speed prevents clogging of the drillholes when creating interlocks in wax.

Selecting a high speed ensures safe and precise drilling even in hard CoCr alloys.

Time and money can be saved by marking the clasps and surveying with a single unit.

Technical Data

Power supply

Power rating

Speed

Chuck

Fuse

Torque

Weight

Dimensions

230 volts / 50/60 Hz

80 watts

0 - 30,000 rpm

Ø 2.35 mm.

thermal overload protection

2.6 Ncm.

18 kg.

250 x 370 x 510 mm

Assortment

4 pieces:

• 1 Milling Unit BF-2

• 1 Handpiece BF-2

• 1 Model Support BF-1

• 1 Control Unit BF-2

Scraping wax surfaces parallel or conical and placing the attachment can both be done with the BF-2.

BF-2 Milling Unit

#140 008 92

*Call for more information: 1.877.328.3965

*Convenient financing with Priority Leasing, Inc.

Call to request a credit application today!

1.800.761.2118.

Model Support BF-1

#730 001 70

$715.00

Milling Base

#140 008 93

$159.00

Transfer Device

2.35 mm Shaft

#360 012 65 $25.50

3 mm Shaft

#360 011 63 $25.50

Accessories / Spare Parts

Chuck Ø 3 mm

#730 001 53 $103.00

Brenometer

#310 000 02 $124.00

Hand Wheel for Tapping

#33001154

$48.50

Milling & Drilling Oil

#550 000 08 $25.50

73

Milling Bur System

Three-Stage milling burs for wax, metal and polishing.

Step 1: Wax

Large cutting volume takes up wax chips easily and avoids smearing of the milling wax.

Sharp cutting edge provides maximum cutting performance in the wax. Optimized twisting angle ensures rapid removal of the wax chips.

Step 2: Metal

Cut With Relief for smooth milling surfaces

& extended edge life of the bur.

Sharp Cutting Edge Relief

Optimized machining angle for maximum cutting performance.

Step 3: Polish

Highly precise cutting edge.

Extremely smooth cutting edge due to polished ledge.

- Produces mirror finish milling surfaces.

Polished Ledge

Parallel Burs

Flat-Top Wax

Milling Burs

0.7mm

F116 2W 07 $25.95

1.0mm

F116 2W 10 $25.95

1.5mm

F116 2W 15 $25.95

2.3mm

F116 2W 23 $25.95

Step 1

Flat-Top Metal

Milling Burs

0.7mm

F116 2H 07 $43.50

1.0mm

F116 2H 10 $43.50

1.5mm

F116 2H 15 $43.50

2.3mm

F116 2H 23 $43.50

Step 2

74

Round-Top Wax

Milling Burs

0.7mm

F137 2W 07 $25.95

1.0mm

F137 2W 10 $25.95

1.5mm

F137 2W 15 $25.95

2.3mm

F137 2W 23 $25.95

Step 1

Round-Top Metal

Milling Burs

0.7mm

F137 2H 07 $43.50

1.0mm

F137 2H 10 $43.50

1.5mm

F137 2H 15 $43.50

2.3mm

F137 2H 23 $43.50

Step 2


Flat-Top Polishing

Milling Burs

0.7mm

F116 2P 07 $25.95

1.0mm

F116 2P 10 $25.95

1.5mm

F116 2P 15 $25.95

2.3mm

F116 2P 23 $25.95

Step 3

Parallel Milling 3 Step Kit - Flat Top

Contains:

1 of F116 2W ** (wax bur)

1 of F116 2H ** (metal bur)

1 of F116 2P ** (polishing bur)

$91.00

**Choose size:

0.7mm Parallel Milling Flat Kit #330 008 16




Tapered Burs

Flat-Top Wax Milling Burs

2°

F186 2W 23

$45.50

4°

F186 2W 31

$45.50

6°

F186 2W 40

$45.50

Step 1

Flat-Top Metal Milling Burs

2°

F186 2H 23

$45.50

4°

F186 2H 31

$45.50

6°

F186 2H 40

$45.50

Step 2

Flat-Top Polishing Milling Burs

2°

F186 2P 23

$45.50

4°

F186 2P 31

$45.50

6°

F186 2P 40

$45.50

Step 3

Round-Top Polishing

Milling Burs

0.7mm

F137 2P 07 $25.95

1.0mm

F137 2P 10 $25.95

1.5mm

F137 2P 15 $25.95

2.3mm

F137 2P 23 $25.95

Step 3

Parallel Milling 3 Step Kit - Round Top

Contains:

1 of F137 2W ** (wax bur)

1 of F137 2H ** (metal bur)

1 of F137 2P ** (polishing bur)

$91.00

**Choose size:

0.7mm Parallel Milling Round Kit #330 008 20




Round-Top Wax Milling Burs

2°

F200 2W 23

$45.50

4°

F200 2W 31

$45.50

6°

F200 2W 40

$45.50

Step 1

Round-Top Metal Milling Burs

2°

F200 2H 23

$45.50

4°

F200 2H 31

$45.50

6°

F200 2H 40

$45.50

Step 2

Round-Top Polishing Milling Burs

2°

F200 2P 23

$45.50

Step 3

4°

F200 2P 31

$45.50

6°

F200 2P 40

$45.50

75


Groove Burs

Flat Groove Burs for Metal

0.7mm

F538 2H 07

1.0mm

F538 2H 10

1.2mm

F538 2H 12

1.5mm

F538 2H 15

$27.50

2.0mm

F538 2H 20

The groove bur exclusively serves to prepare grooves. For this purpose the groove bur is only moved up and down in the vertical axis. The cut on the face simplifies extending the grooves to the cervical direction. At speeds of 15,000 - 20,000 rpm a fine cutting performance and a mirror-like high luster on the milling surface are obtained.

Shoulder Burs

Flat Shoulder Burs for Metal

2.7mm

F205 2H 27

2.9mm

F205 2H 29

The occlusal shoulder is prepared with a special shoulder bur. The shoulder bur features a face cut which smoothens the bottom of the shoulder. Optimum use of this tool is ensured at speeds of 15,000 - 20,000 rpm. A mirror-like luster on the milling surface is achieved with the relief cut. Additional polishing is not required.

Preparation of a Shoulder-Groove Attachment

1

2 3 4 5 6

It is recommended to wax the entire crown in wax prior to starting the milling work.

In the first step a shoulder with a margin step is prepared with a round 2.3mm parallel wax bur.

The insertion grooves are then prepared with the flat 1.0mm groove bur.

The final wax step is to mill an occlusal shoulder with the 2.7mm shoulder bur.

After casting the crown, the parallel surface is finished with the 2.3mm round metal bur.

The insertion groove is finished with the same groove bur. The bur should only be moved up & down in the vertical axis.

7

8 9 10 11 12

The occlusal shoulder is reworked with the

2.7mm shoulder bur.

Finally, a high luster is achieved on the parallel surface using the

2.3mm round polishing bur.

The bredent milling burs produce such a high shine that additional polishing is not needed.

A secondary element with anatomy is created with the Pi-Ku-Plast pattern resin.

The secondary element is cast and fitted onto the crown.

The low shrinkage of the Pi-Ku-Plast pattern ensures excellent precision of fit of the two pieces.

76

Milling burs for non-precious and titanium

Metal Milling Bur, Parallel - Flat top

Metal Milling Bur, Tapered - Flat Top

Ø 1.0 mm

Ø 1.5 mm

N116 2H 10

$43.50

N116 2H 15 $43.50

Ø 2.3 mm N116 2H 23 $43.50

Working speed on non-precious metal 20,000 - 25,000 R·min

-1

2 o taper

4 o taper

N186 2H 23 $45.50

N186 2H 31 $45.50

6 o taper N186 2H 40 $45.50


-1

Metal Milling Bur, Parallel - Round top Metal Milling Bur, Tapered - Round Top

Ø 1.0 mm

Ø 1.5 mm

N137 2H 10 $43.50

N137 2H 15 $43.50

Ø 2.3 mm

N137 2H 23 $43.50


-1

2 o taper

4 o taper

N200 2H 23 $45.50

N200 2H 31 $45.50

6 o taper N200 2H 40 $45.50


-1

Polishing Bur, Parallel - Flat top Polishing Bur, Parallel - Round Top

Ø 1.0 mm

Ø 1.5 mm

N116 2P 10 $25.95

N116 2P 15 $25.95

Ø 2.3 mm N116 2P 23 $25.95


-1

Ø 1.0 mm

Ø 1.5 mm

Ø 2.3 mm

N137 2P 10

$25.95

N137 2P 15 $25.95

N137 2P 23 $25.95


-1

Abrasive burs for titanium, precious and non-precious metal and milling work

A rich quantity of milling and drilling oil is applied onto the milling surface and a speed of 20,000 - 25,000 rotations per minute is used for milling. While adding a copious amount of milling and drilling oil, the milling surface is prepolished with the polishing bur at 20,000 rotations per minute and then polished to high luster at 10,000 rotations per minute.

The cutting edge geometry has been especially designed for rapid removal of material. The relief ensures smooth running and allows very s�

All milling burs are also available in a 3.0 shaft diameter as special order.

Please refer to special order items terms.

77

Diacryl

Diamond instruments for acrylic.

Benefi t: Tremendous noise reduction compared to carbides.

Coarse

Diamond

#340 010 30

$58.50

Universal

Diamond

#340 010 40

$58.50

Papillae

Diamond

#340 010 50

$56.00

Save time and improve quality by grinding acrylic with diamond coated Diacryl rotary instruments. Thanks to their uniform, coarse grit diamond particles with sharp edges and their specifi c shapes, Diacryl diamond instruments are excellent for trimming acrylic dentures quickly and accurately. Thanks to their extra coarse diamond grit and large diameter, these instruments grind aggressively and quietly.

The extra coarse diamond grit and large diameter help to grind aggressively. They are perfect for reducing large areas of acrylic.

The hollow shape keeps them cool and enables them to be used at a higher speed.

Round

Diamond

#340 010 60

$56.00

The universal diamond instrument can be used in lingual and palatal areas. For grinding large papillae and root attachments or lingual bars.

Pointed

Diamond

#340 010 20

$56.00

The pointed flame shape permits the papillae and alveolar attachments to be ground interdentally.

Rubber

Grinder

#340 009 00

$20.95

Diacryl Grinding Instrument Kit

Coarse Instrument

Papilla Instrument

Round Tip Instrument

Pointed Tip Instrument

Universal Instrument

Rubber Instrument

#340 010 70 $282.00

Thanks to the tapered center section of this instrument, uniformly thick peripheries can be created easily and quickly on functional impression trays and partial dentures.

Narrow frames can be rounded and perfected with the pointed diamond instrument.

80 to 100µ 160 to 180 µ

This abrasive rubber instrument creates smooth surfaces on acrylic dentures instead of using sandpaper. The denture can be easily prepared for a high shine.

Set-up Grinding Tool

Two grinding tools in one.

Grinding without exchanging tools in a single working step

• quick adaptation of the underside of the tooth to be set up

• grinding in of occlusal stops

occlusal basal

Set-up Grinding Tool

1 piece

#340 010 10

$62.50

The small, precisely shaped grinding tip with fi ne, perfectly cutting diamond grains provides the ideal precondition for well-aimed and rapid grinding of occlusals contacts.

78

The large grinding area with its optimized shape and selected natural abrasive diamonds ensure maximum removal of material and thus accurate and quick grinding.

Special Diamonds for the Veneering Technique

Perfect finishing of acrylic and ceramic veneers.

#340 008 40

$27.95

#340 008 30

$27.95

#340 008 50

$27.95

The concave part of this tool ensures perfect contouring of the approximal surfaces around the neck of the tooth. Enhanced aesthetics in less time.

The very thin tip of this tool allows the efficient design of tooth necks for single crowns and bridges.

This tool can easily create uniform enamel bulges at the tooth neck. All tools can be used on ceramic and acrylic veneer materials.

The conical grinding tool has a coated face which provides for universal application. The entire design process can be completed with this tool.

79

Diagen

Diamond instruments for zirconium oxide, metal, porcelain, procera and in-ceram.

Diagen Turbo Grinder DTG

5 piece Kit

Cone, 3.5 x 11 mm

Cylinder, 4.8 x 14 mm

Cylinder, 6.5 x 13 mm

Disc, 15 x 3.5 mm

Disc, 22 x 4.5 mm

#340 002 00

$211.00

The diamond instrument with exceptional grinding performance thanks to the special Diagen diamond bonding. High grinding performance and abrasion on metal and porcelain surfaces - only minimal pressure has to be exerted. The prolonged service life in comparison to conventional bonding systems provides for a wide range of applications and high effi ciency.

Maximum grinding power and abrasive capacity on metal and ceramic surfaces at reduced pressure. Increased surface life compared to conventional binding material allows for a wide range of applications and thus high effi ciency.

Diagen Turbo Grinder Ceramic

5 piece Kit

Cone, 3.5 x 11 mm

Inverted Cone, 12 x 6 mm

Inverted Cone, 6.0 x 8 mm

Lens, 22 x 12 mm

Disc, 22 x 2 mm

#340 002 05

$230.00

Diagen Inverted Cone

12 x 6 mm, 1 piece

#340 002 40 $62.50

Diagen Cone

3.5 x 11 mm, 2 pieces

#340 001 50 $58.95

Diagen Cylinder


#340 001 60 $63.95

Gentle and pressure-free grinding allows perfect fi nishing and effi cient removal of material.

The various shapes allow a large application in all areas.

Diagen Inverted Cone

6 x 8 mm, 1 piece

#340 002 50 $51.50

Diagen Cylinder


#340 001 70 $80.00

Grind gently, without exerting pressure, to trim the restoration optimally and reduce the material quickly.

As it only warms minimally during grinding and reduces the material rapidly, this grinding system is perfect on porcelain.

Diagen Disc

22 x 2 mm, 1 piece

#340 002 20 $60.00

Diagen Disc

15 x 3.5 mm, 2 pieces

#340 001 80 $80.00

Diagen Disc

22 x 4.5 mm, 1 piece

#340 001 90 $80.00

80

The diamonds are gripped in place to permit even the hardest acrylics, metals and porcelains to be ground.

Thanks to their Diagen diamond bond, these instruments are well suited for reducing wide areas of material quickly.

Diagen Lens

22 x 2 mm, 1 piece

#340 002 10 $60.00

...additional application examples

Ideal for processing zirconium oxide - recommended by leading implant manufacturers.

The cylindrical shape is perfectly suitable for parallel processing.

The inverted cone with recess provides a cooling effect and thus the perfect precondition for processing zirconium oxide.

Due to their diamond coating, Diagen Turbo grinders represent the ideal tools for processing materials such as glass ceramic or zirconium oxide.

Rapid and convenient shaping of implant suprastructures. The fine diamond particles produce a smooth surface.

The variety of different shapes allow to obtain a wide indication range.

Extremely hard alloys and ceramic materials can be processed as easily as gold.

Abraso-Gum

For polishing of the occlusal surface.

The tip of the Abraso-Gum has a very fine diameter of only 3mm. It finishes the occlusion and grooves very precisely. The system has 3 different textures ranging from Semi-Precious

(PM) to Non-Precious (NP).

Gummy Holder

#350 002 30 $11.00

Abraso-Gum Assortment

#520 001 52 $65.00

• 12 Abraso-Gum red

• 12 Abraso-Gum blue

• 12 Abraso-Gum green

• 12 Abraso-Gum black

• 12 Abraso-Gum brown

• 1 Gummy Holder

81

82

Giflex-TR diamond discs

Controlled saw cuts due to the perforated design.

0.45 mm: The disc for optimal processing

Giflex-TR is a disc for handpieces that features diamond-coating on both sides and is especially suitable for cutting dies out of plaster, refractory and resin.

Calculated chip spaces in the area of the diamond coating ensure quick removal of the grinding dust and increase the cutting performance of the disc. Giflex-TR allows for quick, smooth, and reliable cutting even of very hard plaster and resin.

Troublesome chattering and jamming of the disc is avoided.

Giflex-TR 45 mm

Shaft diameter: Standard 2.35 mm

Diameter: 45 mm

Thickness: 0.3 mm

Recommended Speed:

10,000 - 15,000 RPM

Giflex-TR 45 mm #340 001 10

$57.50

0.37 mm: The universal disc

Larger holes in the diamond free section reduce the friction heat. The disc will not overheat even if deep cuts are carried out.

The running transparency allows for a better view into the saw cut.


Shaft diameter: Standard 2.35 mm

Diameter: 37 mm

Thickness: 0.3 mm

Recommended Speed:

15,000 - 18,000 RPM

Giflex-TR 37 mm #340 000 20

$50.50

0.30 mm: Perfectly suitable for extremely difficult space conditions.


Shaft: Standard 2.35 mm

Diameter: 30 mm

Thickness: 0.3 mm

Recommended Speed:

15,000 - 20,000 RPM

30 mm #340 001 20

$46.50

The grinding dust is removed quickly through the perforations in the diamond free area so that jamming of the disc is avoided.

0.25 mm: For difficult work


Shaft: Standard 2.35 mm

Diameter: 25 mm

Thickness: 0.3 mm

Recommended Speed:

20,000 RPM

25 mm #340 000 25

$40.50

Transfl ex-T diamond discs

The highly fl exible grinding wheel with transparency for safe, concerted grinding.

The highly flexible grinding wheel with transparency for safe, controlled grinding.

Transfl ex Diamond Disc

Diameter: 22 mm

Thickness: 0.25 mm

#340 000 70

$41.00

Transfl ex Diamond Disc

Diameter: 16 mm

Thickness: 0.25 mm

#340 001 00

$39.50

The oblong cutouts in the grinding wheel ensure cooling, high flexibility and the maximum running transparency. This makes it possible to work in a way which is gentle on materials, clear and effi cient while saving time.

Transfl ex diamond discs

Diagonally arranged cutouts for running transparency with high breaking strength and optimal grinding capacity.

Transfl ex Diamond

Disc

Diameter: 22 mm

Thickness: 0.25 mm

#340 000 40

$41.00

Diagonally arranged cutouts for running transparency with high breaking strength and optimal grinding capacity. These discs are designed for delicate work and have to be handled accordingly.

Transfl ex is well suited for dividing and separating in the areas of the anterior and posterior teeth and in the approximate shaping. The specially diagonally arranged cutouts ensure running transparency with high stability and abrasiveness of the grinding disc.

Silicone Burs

Silicone Bur

#S18 7QG 23

$26.95

Thermoformed, soft thermoplastic plates with different degrees of hardness are rapidly and safely ground with these silicone burs; ideal for athletic mouth guards.

The special cutting edge geometry allows the use of soft materials and transition zones towards hard resins.

In orthodontics, silicone positioners can be perfectly ground due to the excellent guidance.

Silicone Bur

#S26 3QG 60

$42.00

Silicone Bur

#S23 7QG 65

$46.00

Due to the different shapes, these burs can be used to shape silicone in hardly accessible areas such as the alveoli of the gingival mask.

Due to the controlled removal of material, a smooth transition zone from the silicone to the denture resin is achieved.

The ground surface is smooth and free from any residue.

83

Spot Clip

Hemostat with spot-shaped holding area simplifies veneering.

Bredent Spot Clip with

Supporting Ring

1 piece

#310 000 07

$142.00

Every ceramic specialist is familiar with the problems of metalceramic crowns without a metal margin: the holding spot of the hemostat is not sufficiently covered by base material (opaque).

The problem can be solved with

Spot Clip.

The clip only covers a tiny spot of the surface to be veneered.

The base material can be easily applied around the holding spot of a clip.

Mamelon Cutter

Simplifies the incisal design of ceramic crowns.

After removing the Spot Clip, the aqueous base material fills the holding spot of the clip. This way a uniform smooth layer of base material is obtained.

Spot Clip simplifies the application of stains and glaze material.

No smearing of stains, no subsequent application of stains in the area of the holding spot of the clip is required.

Large mamelon cutter for upper jaw incisors

Small mamelon cutter for lower jaw incisors

84

The crowns are shaped as usual using dentine material.

The incisal end is cut back using the mamelon cutter.

The contoured dentine core after firing: A base for incisal design options is obtained in a fast, safe and easy way.

Mamelon Cutter

1 piece

#310 000 01

$43.95

The individual shades can be applied onto the dentine core - regardless of whether firing has been carried out or not.

The incisal edges of the finished crowns exhibit a vivid display of colors.

Cervical Disc

For quick, precise cutting of the cervical margin.

This precision steel cutting disc is 0.1 mm thick and 3.0 mm in diameter. It increases precision and reduces working time when cutting the margin on wax or plastic copings. You can achieve a better marginal fi t with the cervical disc than with a scalpel.

Cervical Disc

1 piece

#320 009 10

$92.00

Precise 0.1 mm steel disc with 3 mm diameter. Guaranteed exact, clean cut.

Comparison between a scalpel (left) and the Cervical Disc (right).

Cervical Disc creates a precise cut around the margin so that a second wax-up on the margin is not necessary.

Articulation Paper Holder

Repeated picking up and placing down of the handpiece and articulation paper are no longer necessary.

Articulation paper holder size 1

1 piece

17 mm

#360 012 17

$24.50

Grinding in a fl ick of the wrist!

Articulation paper holder size 2

1 piece

20 mm

#360 012 20

$24.50

85

Ceramix

• Accurately measure

& dispense ceramic materials!

Dispensing syringe designed to accurately measure and dispense ceramic materials. Reproduce individual shade mixtures while minimizing waste. The syringe is made up of a cylindrical tempered glass scale and a smooth, machined stainless steel plunger.

Ceramix

#360 011 95

$85.00

To use Ceramix, simply select the desired quantity by pulling the plunger until it reaches the chosen number on the scale. Make sure the porcelain powder is condensed well in its container and insert the syringe. Extrude the selected amount on to your favorite ceramic mixing tray and mix the porcelain as usual. Ceramix can also be used to make custom shade tabs.

Quick Tool

• Safe & uniform grip!

Diamond tip instrument designed to produce a safe and uniform grip of crowns and bridges for easy handling. Porcelain crowns are held without any pressure due to the three diamond plated tips and the adjustable locking mechanism; even electro-formed copings can be safely secured.

Quick Tool

#310 010 20

$185.00

In the case of reduced spaces such as in lower anterior crowns, a diamond tip can be removed. Additionally, the Quick Tool from Bredent has an integrated “slide condenser” that can be used for controlled condensing of porcelain during the build-up stage. The diamond tips for this instrument can also be purchased separately.

“Slide Condenser”

86

Ergonomic Wax Knife

• Dual tipped, all-in-one, light weight instrument for fast

and accurate waxing of removable prosthetics!

Ergonomic

Wax Knife

#310 000 13

$65.00

Dual tipped, all-in-one, light weight instrument for fast and accurate waxing of removable prosthetics. Suitable for right and left handed users. A unique, edged shaped tip allows fast waxing and carving of age-specific interdental papillae. The other end is an edged shaped spoon that is suitable for easy festooning as well as applying large amounts of wax. The spoon shaped tip has an additional curvature that makes it ideal for carving and shaping the peripheral border and transition areas of a denture. Natural looking wax-ups are created quickly and comfortably with the Ergonomic Wax Knife from Bredent.

The

Cobra

“The Cobra”

• Repositioning Tweezers

• Quickly grab and secure small components!

Uniquely machined jaw tips designed to quickly grab and secure small components such as crowns, implant screws, attachments, and denture teeth. Minimize the loss of these items during steam cleaning with the Cobra!

“The Cobra”

Repositioning Tweezers

#310 001 15

$65.00

87

Thermo-Pen

Portable flameless device!

Fast and efficient adaptation of thermoplastic clasps and accessories

• Can reach temperatures up to 250ºC or 482ºF

• Has an adjustable temperature controller

• Can be refilled using a high quality butane gas

Thermo-Pen

#110 014 70

$305.00

PROPER STORAGE!

Quick Change

Interchangeable system of instruments for: ceramics, c&b waxing and waxing of removable prosthetics

• Corrosion resistant

• Proper storage of sensitive ceramic blades

• Ceramic brushes can be perfectly stored in a hanging position

• Maximum safety when replacing heated tips

Holder

1 piece #310 010 30

$130.00

Carbon Handle

1 piece #310 010 31

$70.00

Croco Smooth

#310 010 32

$34.50

Blade according Zahle

#310 010 40

$40.00

Croco Serrated

#310 010 33

$34.95

Probe 0.8

#310 010 41

$29.75

Fissure Tool

#310 010 34

$36.50

Probe 1.1

#310 010 42

$29.00

Adapter

#310 010 35

$16.50

Blade

#310 010 37

$40.00

Blade

#310 010 39

$40.00

Koli Brush size 6

#310 010 44

$23.95

Koli Brush size 8

#310 010 45

$29.00

Koli Brush size 8B

#310 010 46

$64.50

88

Magic Contrast

Brush size 6

#310 010 53

$35.95

Magic Contrast

Brush size 8

#310 010 54

$40.50

Magic Contrast

Brush size 8B

#310 010 55

$62.50

Twin Point

#310 010 56

$34.50

Olive with Teeth

#310 010 57

$34.50

Transfuser

Safe and simple fi lling of investment material

• No formation of air bubbles thanks to the highly fl exibility of the silicone tip

• Ideal handling in narrow areas through the use of the bent tip

• Liquid repellent tip

Transfuser

4 pieces #390 S00 04

$71.95

1 piece #390 S00 01

$25.00

Quick Change

Interchangeable system of instruments for: ceramics, c&b waxing and waxing of removable prosthetics

Previously, air could be entrapped when pouring investment material into the modelation.

Highly fl exible, soft tip - no risk of damage to the wax modelation.

Narrow areas are carefully and completely filled without damaging the modelation.

Perfect flow of material and bubble-free condensing with the

Transfuser.

Waxpool Duo

All-in-one wax dipping unit and wax knife

• Digital controls for added comfort

• ºC or ºF can be selected

• Exchangeable lids

• Precise temperature control for producing accurate copings

• High performance heating elements reduce melting time of waxes

• Recessed dipping well helps avoid fi nger burning

• Dipping pots reach a melting temperature of up to 120ºC (250 ºF)

• Fatigue-free working due to ergonomic design of wax knife

• Special heat insulating grips

• Fast exchange of waxing tips

• Boost key for quick heating of wax knife to fi nal temperature

of up to 240ºC (464ºF)

• Burn resistant cable

Waxpool Duo Dipping Unit

1 piece #110 015 00

$450.00

Waxpool Duo Dipping Unit

& Wax Knife Handpiece

4 pieces:

1 Waxpool Duo Unit

1 Waxpool Duo Handpiece

2 Contouring Blades of choice

#110 015 20

$630.00

Waxpool Duo Handpiece

#110 015 10

$102.50

Contouring Blade size 1

#320 WP4 G1

$46.50


#320 WP4 G3

$46.50


#320 WP4 G5

$46.50

Contouring Blade standard

#320 WP4 72

$46.50

89

Gnathoflex Premium

C

Size

B A

429 P01 4_

429 P01 5_

429 P01 6_

Tooth Number

5

12

4 13

3 14

A

Size

B C

429 P02 4_

429 P02 5_

429 P02 6_

429 P01 7_

Upper Right

Lower Right

429 P04 7_

2 15

31 18

429 P02 7_

Upper Left

Lower Left

429 P03 7_

429 P04 6_

30 19

429 P03 6_

429 P04 5_

29 20

429 P03 5_

429 P04 4_

28 21

For order number, replace _ with A, B, or C as per required mold size

$25.50 each

429 P03 4_

Gnathoflex Premium 16 pc. kit

16 forms in size A

#429 P00 0A $318.00


16 forms in size B

#429 P00 0B $318.00

90


16 forms in size C

#429 P00 0C $318.00

Assortment:

Gnathoflex Premium

48 pieces, consisting of 16 different molds in 3 sizes A-B-C

#429 P00 48

$798.00

Isoflex

20 ml

Ceramic insulating liquid

#540 010 13

$45.000

Video

Gnathoflex Premium Video

(Free with purchase of any Kit)

#VID-BREGNA

$10.00

NEW!

Aesthetic Gnathoflex

Size

D C B

Tooth Number

429 A14 5_ 5

12

429 A14 5_

4 13

429 A01 6_ 3 14

Size

B C D

429 A24 5_

429 A24 5_

429 A02 6_

429 A01 6_

Upper Right

Lower Right

429 A04 7_

2 15

429 A02 6_

Upper Left

Lower Left

429 A03 7_

31 18

429 A04 6_

429 A04 5_

429 A04 4_

30 19

29

20

28 21

For order number, replace _ with B, C, or D as per required mold size

$25.50 each

429 A03 6_

429 A03 5_

429 A03 4_

Aesthetic Gnatho Flex 36 pc. Assortment

12 forms in 3 sizes - B, C, D

#429 A00 36 $695.00

Isoflex ceramic insulation liquid

Required when using the Aesthetic Gnatho

Flex with porcelain.

20 ml #540 010 13 $45.00

91

Wax occlusals

The copings are prepared as usual, using wax or acrylic.

To compensate for the thicknesses of the Gnathoflex, the bite is raised by .5 mm.

Fill Gnathoflex with wax and wait until the wax begins to gel.

Once the wax has hardened, place the Gnathoflex occlusal onto the coping.

Close the articulator in the position of the maximal intercuspidation and attach the occlusal to the coping using a drop of wax. Depending on the situation, two or more Gnathoflex occlusals can be placed simultaneously or one after the other. The contact can be strongly varied by raising or lowering the antagonist.

High-luster, gnathologically shaped wax occlusals with perfect contact to the antagonist are the perfect basis for smooth and precision-fit casting. Gnathoflex

Premium helps to save time during the preparation of the wax model as well as during finishing of crowns and bridges

Acrylic occlusals

Prepare the structure as usual and apply crown and bridge acrylic (dentine).

No separating agent is required when filling the Gnathoflex with acrylic. First fill the cusps with incisal and then fill the mold completely with dentine.

Ceramic occlusals

Place Gnathoflex on the bridge, close the articulator and polymerize with UV light in order to fix the bite.

Then the bridge is removed, interdental contact areas are applied and polymerization is completed.

The opaque is fired on the metal structure. Hold the Gnathoflex with the tweezers and apply Isoflex insulating liquid onto the inner surface. Tap several times on the Gnathoflex to remove excess Isoflex insulating liquid. Fill incisal into the cusps and brush out form the cusps toward he margins. Fill the Gnathoflex with dentine and place on the bridge structure. Close the articulator and turn it. Fix the Gnathoflex occlusals to the bridge using dentine material. Dry the object and carefully remove the Gnathoflex. The other occlusals are prepared accordingly.

92

NEW!

Seracoll UV

Light curing wax adhesive liquid.

Seracoll UV is a new light curing wax adhesive liquid from Bredent that is designed for use in creating stress-free connections in C&B and implant bar wax-ups. It is also suitable for fabricating wax-ups for the copy milling technique. Seracoll UV is totally homogenous with waxes and cures in any light curing unit with a UV or LED wavelength range of 270 – 580 nanometers in approximately 10 seconds; and, it burns

-out clean and residue-free. This light curing liquid adhesive for waxes is highly accurate and saves time compared to using pattern resins for similar applications.

• Low viscosity

• Light curing, cures in all dental units

• Versatile

• Highly accurate and stable

• Clean burning

• Saves time

• Convenient packaging prevents spillage during use

Seracoll UV

#540 011 51

$44.00

NEW!

compoForm UV

Light-curing composite for modelling, fi xation of separated bridges and for quick fabrication of post and core restorations. compoForm UV burns out without leaving any residue and produces homogeneous casting results.

Individual modelling directly from the syringe. Thanks to immediate hardening with a polymerization lamp, the model can be built up in a safe and controlling manner.

The stability of compoForm UV renders the material perfectly suitable for the transfer of the jaw situation and, consequently, stress-free working is ensured.

compoForm UV

2 x 3 mL syringes

10 application cannulas

#540 011 50

$79.50

compoForm UV can be used in conjuction with modelling wax and is perfectly suitable for interlocking the model prior to investing. This way investing without any deformation is possible.

Modelling and further processing of telescopic and conical crowns can be perfectly controlled by means of a visual check of the layer. The high stability of the hardened composite allows reworking with a bur.

Thanks to low shrinkage and burning without any residue, the composite is ideal for fi xation of bridges to be soldered.

Accessories

Application cannulas

25 pieces

#580 000 18

$20.50

Model cast extensions can be fabricated in a simple and timesaving manner. compoForm UV can be easily removed from the plaster.

Undercuts on dies can be quickly and completely blocked out.

Burning without any residue and reduced swelling behavior provide perfect preconditions for top-quality casting results.

93

Standard Modelling Wax

94

Bredent K2 Exact Carving Wax

Highly precise, pure sculpting wax.

Bredent K2 Exact Carving Wax will be delivered as a 60 g., fully anatomical first molar. For crowns, bridges, and inlays. The recently developed components of this wax offer maximum stability for modeling and ideal scraping properties.

Raw materials which have undergone multiple purity checks guarantee optimal casts. As a result of better luminous reflectance, the natural dies make it easier to shape crowns and bridges anatomically.

K2 Exact Gray

60 g

K2 Exact Yellow

60 g

K2 Exact Beige

60 g

K2 Exact Green

60 g

#510 009 02 $27.50

#510 009 03 $27.50

#510 009 04 $27.50

#510 009 05 $27.50

Standard modelling wax for crowns, bridges, and inlays with a solidification point of 50 degrees celsius.

Standard Modelling Wax - Beige, 70g

#510 007 85

$21.50

Clean casts and burnout

Marble base and clear acrylic dome

(does not include wax)

#320 004 20

$42.50

Splendido Wax

$13.50

The light green color of this wax provides for improved light reflection and facilitates determination of the final contouring. The opacity of this wax allows for improved determination of the depth of the fissures in the wax pattern. This wax is suitable for fabricating all types of patterns - crowns, bridgework, inlays - and can be milled. “Splendido hard” can be milled at room temperatures of up to

40 o

C, making it particularly suitable for use in summer.

Splendido medium, light green 25g

#510 006 90

Splendido hard, light green 25g**

#510 005 90

**Splendido hard is suitable for milling applications

KBI Wax

$13.50

KBI is a new generation sculpturing wax, exhibiting the following properties: Minimal shrinkage, remains where placed, easily sculptured and forms firm shavings which leave a smooth surface. Ideal for any wax-up technique. The light blue color enables the technician to view the contours and surface structure of the pattern in greater detail. “KBI hard” is available for use in summer. Both waxes are suitable for milling.

KBI medium, light blue 25g

#510 009 10

KBI hard, light blue 25g**

#510 009 20

**KBI hard is suitable for milling applications

Life Color Wax

Tooth Colored

This wax was developed specifically for use with the M.A. Polz technique of wax-up. It is ideal for training apprentices, as the anatomical contours are more readily recognized. This wax exhibits minimal shrinkage and is available in two consistencies - medium and hard.

$10.95

Life color wax, tooth colored, medium 25g

#510 008 00

Life color wax, tooth colored, hard 25g

#510 008 10

Life Color Wax

$10.95

Dark Brown

This is the classic supplement to the tooth colored Life Color wax. It is ideal as a cervical and coping wax as its dark base color improves the color contrast of the fissures. It is also available in two consistencies - medium and soft.

Life color wax, dark brown, soft 25g

#510 008 20

Life color wax, dark brown, medium 25g

#510 008 30

Cervical Wax

In order to achieve a perfect marginal seal on crowns, inlays, onlays, etc., the wax must adapt well and be completely shrink-free. Cervical

Wax is used for forming the cervical margin and adheres perfectly to the coping and sculpturing wax.

$8.95

Cervical Wax, red 25g

#510 006 05

Wax For Outer Copings

For fabricating outer copings onto metal. Easily spread and, while cooling, will not form creases on the surface exposed to the metal. Extremely good precision of fit, thanks to the minimal shrinkage.

$8.95

Wax for outer copings, yellow 25 g

#510 004 20

(Underpull wax)

Undercut Wax

This wax was developed in order to block out cavities in dies. It exhibits minimal shrinkage and adheres well. Its white color contrasts well with all types of die material.

Undercut wax, white 25g

#510 004 80

$19.95

Sticky Wax

As it sets quickly and adheres very well, this sticky wax can be used for all techniques. It is easily boiled off, without leaving residue, thus guaranteeing clean surfaces.

Sticky wax, dark red 25g

#510 004 00

$7.95

Gecko Sculpturing Wax

This sculpturing wax is available in the same colors as dental stone, for orientating the wax pattern to the model. The colors give an overall view of the pattern and the remaining dentition, thus enabling the user to compare them objectively. These waxes are based on new conceptions for speeding up fabrication of wax patterns and improving their precision, and are intended to meet the demands of everyday dental technology. Close cooperation with dental technicians and master technicians enabled the waxes to be optimized for use in all branches of dental technology. These waxes can be applied precisely, have excellent contouring, and produce firm shavings which leave a very clean surface.

Gecko green for Die Keen, 25g

Gecko beige for Fuji Rock, 25g

Gecko red for Vel- Mix- Stone, 25g

Gecko yellow for Super Die, 25g

#510 006 01 $13.50

#510 006 02 $13.50

#510 006 03 $13.50

#510 006 04 $13.50

95

Dipping Waxes

Accurate, precise fitting copings.

Dipping wax canary yellow, 130g

Dipping wax red, 130g

Dipping wax green, 130g

#510 008 50 $56.95

#510 008 60 $56.95

#510 008 70 $56.95

An extremely precise pattern produced using our dipping wax without the need to re-wax the cervical margin.

Using this method you can save up to 90 % of your material costs compared to copings made using vacuum forming systems. The dipping wax requires no separating medium for removal from smooth preparations or metalwork. The wax forms a constant thickness. Dipping wax is supplied as beads.

Shows the constant wax thickness and excellent marginal fit without having to re-wax the cervical margin. Dipping wax is supplied as beads.

The dipping wax requires no separating for removal from smooth preparations or metalwork. Hence it is ideal for precision dental technical work.

Use the white wax to block out untercuts or to build up the ideal form of preparation. It does not adhere to the other waxes.

Use the dentine colored wax in conjunction with castable ceramics and when producing Life Color wax copings.

96

Elaflex

Super-elastic dipping wax for highly precise wax copings.

Even in inlays, the cavities can be precisely prepared using Elaflex. This way, modeling is simplified.

Elaflex is so flexible that the wax coping is not deformed when it is removed.

Elaflex is self-insulating on all metal parts that are polished to high luster.

Elaflex, purple

130g.

#510 009 00

$56.95

Visio-Dip

Dipping wax allowing visual control at a wax thickness of 0.3 mm.

0.3mm

At a wax thickness of more than 0.4 mm the die is no longer visible.

The die becomes visible at a layer thickness of 0.3mm. Less finishing work is required if a precise wax thickness is ensured.

Visio-Dip, mustard yellow

130g

#510 007 30 $56.95

97

Biotec Wax System

The Biotec Wax System is a full line of waxes, pontics, sprues and liquids designed specifically for pressable ceramics. The low shrinkage and clean burnout characteristics of these components makes them ideal for cases which require the utmost precision.

100% ORGANIC & ASH FREE

FOR PRESSABLE CERAMICS

Biotec Modelling Wax, gray

60 g

#510 006 10 $29.95

Biotec Cervical Wax

28 g

#510 006 12 $25.50

Biotec Modelling Wax, green

60 g

#510 006 11 $29.95

Biotec Milling wax

28 g

#510 006 14 $25.50

Biotec Wax for Outer

Copings

28 g

#510 006 13 $26.95

Biotec Blocking Out Wax

28 g

#510 006 15 $25.50

Biotec Wax Pontics

98

Biotec Wax Sprues

$27.00

(Details on page 102)

Biotec modelling wax

Modelling wax made for the best modelling properties, shrinkage and complete burn out.

• The excellent scraping properties ensure perfect fit of the wax crown on the die.

• Wax residues can be blown away easily.

• Low shrinkage leads to high precision of fit.

• Residue-free burn out is the prerequisite for homogeneous casting.

• Perfectly suitable for modelling pressable ceramic crowns and inlays.

60 g

#510 006 11 $29.95

60 g

#510 006 10 $29.95

Easily controllable stability for specific application across small and large areas.

Biotec wax for outer copings

Modelling wax for uniform layering with low shrinkage and outstanding burn out properties.

28 g

#510 006 13 $26.95

Uniform coping thickness due to perfect scraping properties. When the die shines through, a layer thickness of 0.3 to 0.4 mm has been achieved.

Low shrinkage and excellent burn out properties ensure utmost precision of fit and homogeneous castings.

99

Biotec cervical wax

Modelling wax for precision-fit crown margins due to low shrinkage and outstanding burn out properties.

The special consistency of this wax, minimum shrinkage and extremely low quantity of residues of combustion ensure perfect fit of the crown margin.

Biotec cervical wax

28 g

#510 006 12 $25.50

Biotec blocking out wax

Special wax for blocking out undercuts with very good scraping properties. No discoloration on the plaster model after boiling out.

Biotec Blocking Out Wax

28 g

#510 006 15 $25.50

The special components of the blocking out wax ensure perfect blocking out of undercuts.

Easy and quick scraping allows one to save time.

No color additives penetrate into the plaster surface after boiling out the model. The master model remains clean.

100

Biotec milling wax

Excellent milling wax with superb modelling properties.

Biotec Milling Wax

28 g

#510 006 14 $25.50

Enormous amount of time is saved due to good modelling properties since no other wax is required for the shear distributor.

For selection of milling burs, see page 74-77.

Outstanding scraping and milling properties since sticking of wax to the bur is avoided.

Extremely accurate milling wax to produce smooth and shining surfaces during milling.

Can be used for pressed ceramics since the wax burns out almost entirely.

101

Biotec wax sprues

Sprue wax with organic components, highly flexible and burns out completely.

Diameter (mm) Order #

1.2

1.5

2.0

2.5

3.0

3.5

4.0

5.0

430 080 12

430 080 15

430 080 20

430 080 25

430 080 30

430 080 35

430 080 40

430 080 50

$27.00

$27.00

$27.00

$27.00

$25.00

$25.00

$25.00

$25.00

High flexibility and low elastic recovery after shaping allow specific stress-free attaching of the sprues. Residue free burn out is the basis for perfect casting results. Perfectly suitable for modeling pressed ceramic crowns and inlays.


Micro-fine insulating liquid on organic basis for reliable, exact separation of the wax pattern against all materials.

Isobre wax insulating liquid on organic basis is absolutely reliable, solvent-free and can be washed off easily. Neutral against plastic, ceramic, metal, plaster and painted surfaces. Even when the insulated surface has dried, Isobre wax insulating liquid will produce a highly efficient, micro-fine insulating layer which ensures simple and safe removal of the wax pattern. Highly absorbing surfaces must be insulated

2 to 3 times.


750 ml

#540 010 40 $33.50

Empty Brush pen

20 ml

#540 007 20 $11.50

Wax-Lite surface tension reducing agent

Alcohol-free surface tension reducing agent for bubble-free investing of wax patterns.

Wax-Lite surface tension reducing agent

750 ml

#520 010 08

$35.50

Spray Bottle

(empty)

125 ml

#540 007 50

$6.50

Wax surfaces that are coated with this agent allow the flowing of the investment material into very fine recesses of the wax pattern so that smooth, homogeneous surfaces and clean occlusal surfaces result. With the spray bottle, micro-fine layers of Wax-Lite can be applied on the wax surface. Tension free investing of very thin patterns is ensured due to the absence of evaporation cooling of the alcohol.

102

Biotec pontic blocks without collar B-MKBL OG

Ash free pontics with properties similar to modeling wax. Ideal for pressable ceramics.

B13 122 2C

B13 122 2B

B13 122 2A

UPPER

B13 171 4C

B13 171 4B

B13 171 4A

B13 242 7C

B13 242 7B

B13 242 7A

1

RIGHT

32

16

LEFT

17

B13 474 4A

B13 474 4B

B13 474 4C

LOWER

B13 343 7A

B13 343 7B

B13 343 7C

B-MKBL OG Metal Ceramic Blocks 90 piece kit

5 blocks of each 18 forms

#B13 180 05 $252.00



#B13 180 10 $458.00



#B13 180 20 $798.00

B13 423 2A

B13 423 2B

B13 423 2C

Refill Packages (RP):

Each form and size is available as a refill package

25 pieces each

$58.50

Mini kit:


#B13 000 MK

$107.50

The melting point, hardness and scraping properties are adapted to the modeling waxes to allow simple and specific connecting of the pontics with the crown pattern. The extremely low quantity of residues of burn out of the Biotec pontics provide perfect preconditions for smooth, homogeneous cast surfaces. The ash free burnout makes it ideal for pressable ceramics.

103

Between Blocks BW-BL

This is a porcelain wrap-around pontic with no lingual collar. It is designed to use the same amount of metal as a hollow pontic.

D00 122 2C

D00 122 2B

D00 122 2A

D00 171 4C

D00 171 4B

D00 171 4A

D00 242 7C

D00 242 7B

D00 242 7A

D00 474 4A

D00 474 4B

D00 474 4C

D00 423 2A

D00 423 2B

D00 423 2C

Available in 25 piece refill kits $58.50

Available in yellow wax only

BW-BL Between Blocks 36 piece Mini Kit

2 blocks of each 18 forms

#D00 00B MK $107.50

BW-BL Between Blocks 90 piece Kit


#D00 180 05 $252.00

Posifix

The ideal, gray sticky wax for positioning wax patterns.

50g #430 016 37 $38.95

104

D00 343 7A

D00 343 7B

D00 343 7C

In Between Pontics BWG

This is a porcelain wrap-around pontic with no lingual collar. It is designed to use the same amount of metal as a hollow pontic.

C

SIZE

B A

TOOTH

A

SIZE

B C

D00 001 1_

D00 001 2_

D00 002 1_

D00 002 2_

D00 001 3_

D00 0K0 P_

D00 0K0 P_

D00 002 3_

D00 0K0 P_

D00 0K0 P_

D00 171 6_

D00 262 7_

D00 171 6_

D00 262 7_

D00 474 6_

D00 474 6_

D00 004 5_

D00 004 4_

D00 004 3_

D00 UKO F_

D00 UKO F_

For order number, replace _ with A, B, or C as per required pontic size


Available in yellow wax only

D00 363 7_

D00 363 7_

D00 003 5_

D00 003 4_

D00 003 3_

D00 UKO F_

D00 UKO F_

BWG In Between Pontics 108 piece Mini Kit

2 pieces of each 54 forms

FREE BWG Instructional Video

#D00 000 MK $107.50

BWG In Between Pontic 270 piece Kit

5 pieces of each 54 forms

#D00 540 05 $252.00

Posifix


50g #430 016 37 $38.95

105

Hollow Pontic Blocks HP-BL

A11 122 2C

A11 122 2B

A11 122 2A

A11 171 4C

A11 171 4B

A11 171 4A

A11 242 7C

A11 242 7B

A11 242 7A

106

A11 474 4A

A11 474 4B

A11 474 4C

A11 423 2A

A11 423 2B

A11 423 2C

Available in 25 piece refill kits only $58.50

Available in blue wax only

HP-BL Hollow Pontic Blocks 90 piece Kit


#A11 180 05 $252.00

HP-BL Hollow Pontic Blocks 36 piece Mini Kit


#A11 000 MK $107.50

Posifix


50g #430 016 37 $38.95

A11 343 7A

A11 343 7B

A11 343 7C

Pontics with Shallow Collars for Ceramic

This is a full body design with a traditional lingual collar.

A01 122 2C

A01 122 2B

A01 122 2A

A01 171 4C

A01 171 4B

A01 171 4A

A01 242 7C

A01 242 7B

A01 242 7A

A01 474 4A

A01 474 4B

A01 474 4C

Palatinal & Lingual Views

A01 423 2A

A01 423 2B

A01 423 2C



FGMK-BL Pontics with shallow collars for ceramic 90 piece Kit


#A01 180 05 $252.00

Posifix


50g #430 016 37 $38.95

A01 343 7A

A01 343 7B

A01 343 7C

107

AK-BL Pontics with Aesthetic Anatomical Occlusals

This is a fully anatomical aesthetic occlusal pontic design with hollow interiors.

A12 171 4C

A12 171 4B

A12 171 4A

A12 242 7C

A12 242 7B

A12 242 7A

A12 474 4A

A12 474 4B

A12 474 4C



AK-BL Pontics with Aesthetic Occlusals 60 piece Kit


#A12 120 05 $170.00

Posifix

Gray wax for positioning pontics and wax patterns.

A12 343 7A

A12 343 7B

A12 343 7C

Posifix


50g #430 016 37 $38.95

108

Posifix wax simplifies placement of individual pontics and pontic blocks. Posifix is sticky enough to hold the patterns precisely in place but still can be removed cleanly without any residue.

Aesthetic & Ergonomic Pontics for Ceramic

A02 122 2C

A02 122 2B

A02 122 2A

A02 171 4C

A02 171 4B

A02 171 4A

A02 242 7C

A02 242 7B

A02 242 7A

A02 474 4A

A02 474 4B

A02 474 4C

Palatinal & Lingual Views

A02 423 2A

A02 423 2B

A02 423 2C




#A02 000 MK $107.50

Posifix


50g

#430 016 37 $38.95

A02 343 7A

A02 343 7B

A02 343 7C

109

Chrome Cobalt Bonding Agent

Pre-opaque that allows porcelain to be fi red onto chrome cobalt & non-precious alloys.

Prevents metal oxides from chrome cobalt alloys, non-precious and semi-precious alloys.

Results in an excellent ceramic bond while retaining the original shade of the porcelain.

As it is a ceramic material, it bonds extremely well with opaques.

A layer of 10-20 microns is suffi cient. No dark margins, even close to metal collars.

Compensates for discrepancies between the coeffi cients of expansion of porcelain and metal.

Can be applied without using any extra procedures or equipment.

Chrome Cobalt Bonding Agent Instructions

1. Pre-treating the metal coping: 2. Applying the bonding agent

After trimming and fi nishing the coping, sandblast it. Following this, the coping should either be boiled for 10 minutes in distilled water or thoroughly steam cleaned. At this stage the coping should only be held with tweezers. The coping must be thoroughly dried before the chrome cobalt bonding agent is applied.

Mix the chrome cobalt bonding agent into a thin consistency using distilled water. Apply one masking coat of chrome cobalt bonding agent with a staining brush. While doing so, go over the metal/porcelain junctures to avoid discolorations in the border zones.

Important:

Chrome cobalt bonding agent can be mixed only once. Should the mix dry out, it is no longer suitable for use.

Troubleshooting:

-Cracks in the chrome cobalt bonding agent:

Consistency or layer too thick. Sand-blast and reapply properly.

-Blisters in the chrome cobalt bonding agent:

We recommend degassing the coping before the bonding agent is fi red, by heating to 980ºC in vacuum and holding for 10 minutes.

-Green/Black spots:

Either the bonding agent was mixed too thinly, the coping was moist or greasy or dried out material was re-used.

-Cracks in the porcelain:

Can occur if the metal coping is disproportionately small in relation to the volume of the porcelain or if the metal connectors are defective. Should a reddish-brown layer appear instead of a yellow one, then the alloy is unsuitable. Simply use another commercially available chrome cobalt alloy.

To date, only three alloys have been proven unsuitable: Crutanium, Crystalloy and Ticonium.

Ceram-Bond

For increased reliability with alloys.

The premixed, ready-to-use Ceram-Bond allows you to omit oxide fi ring when veneering metal frameworks. Ceram-Bond is applied immediately after fi nishing, sandblasting, and cleaning metal framework. This micro-fi ne layer improves bonding of the ceramic material to the metal framework, protects against spalling and offers increased reliability.

3. Firing the chrome cobalt bonding agent

May vary according to individual furnaces.

Recommended values:

Initial Temperature: 650ºC.

Final Temperature: 980ºC in vacuum.

Rate of Temperature increase: 55ºC per minute.

Once the final temperature has been reached, remove the coping from the furnace. The coping should now have a yellow or golden yellowish appearance.

At this stage, the opaque can be applied, according to the porcelain manufacturer’s instructions.

Many dental laboratories have successfully worked with our chrome cobalt bonding system. Despite this, we recommend testing the bond on a sprue button made from your chrome cobalt alloy. Poorly processed alloys can also lead to defects. Often alloys are overheated and burnt during casting.

Chrome Cobalt Bonding Agent

8 ml #520 003 21 $78.50

39 ml #520 003 20 $294.00

Ceram-Bond

7 g #520 003 23 $78.50

110

Microceramic

Perfect cast surfaces due to microfi ne investment layers for crowns and bridges and CoCr work.

In the fi eld of crowns and bridges, Microceramic is especially suitable for non-precious alloys since very cast surfaces are obtained. The Microceramic is adapted to the expansion of the investment material.

An extended processing time span allows precise application of the Microceramic. Microscopically fi ne ceramic particles ensure perfect reproduction of very fi ne details of wax models.

Without Microceramic With Microceramic

The difference after sandblasting with glass beads can be clearly recognized: The entire oxide layer can be easily removed so that less working time is required.

Microceramic

125 ml

#550 000 12

$31.50

Devesting is simplifi ed since there is no bonding between the investment material and Microceramic.

Accessories

3 brush size A + 1 brush holder #330 011 46 $25.95

3 brush size B + 1 brush holder #330 011 47 $25.95

3 brush size C + 1 brush holder #330 011 48 $25.95

Microceramic avoids extreme formation of oxide on non-precious metal alloys.

Cast objects are only sandblasted with 50 micron glass beads to obtain almost perfect high luster. Consequently, time for further processing is saved.

111

Pi-Ku-Plast HP 36

For accurate, stable and millable resin dies and frameworks.

Optimum contouring properties, will not slump. Available in 5 different transparent colors to allow the thickness to be checked and to contract well within the wax. When used with the Pi-Ku-Plast separating agent, resin inner copings can be base for producing milled restorations. Ideal for connecting bar sections for soldering.

Due to the multigrain design, Pi-Ku-Plast absorbs less monomer and therefore has less shrinkage. Various grain sizes shift into the gaps of each other for a compact, sturdy application. The burnout is clean and complete.

In burnout, Pi-Ku-Plast does not expand but collapses. This puts no internal stress in the casting ring, resulting in a clean, stress-free casting.

Brush Size A Brush Size B

Pi-Ku-Plast Dip System

Control viscosity, Save material, Save time, Save money

Dip the flat side of the brush into the polymer to take up large portions.

Dip the narrow side of the brush into the polymer to take up small portions.

Wet the brush with the Pi-Ku-Plast monomer. The amount and firmness of the portion can be controlled by the amount of monomer on the brush and the time it is immersed in the polymer. Because the material does not have to be pre-mixed, no resin is wasted due to overmixing the two components. After using, the brush is cleaned in the cleaner and the vessels are covered to keep the Pi-Ku-Plast in good working condition.

Dip only the brush tip into the polymer to take up very small portions.

Optimal control of layer thickness thanks to the transparent colors of Pi-Ku-Plast HP36

Thanks to the smooth, high-lustrous reproduction of the metal surface of the primary element, a perfect inner surface of the secondary crown is obtained.

By using Pi-Ku-Plast Separating

Agent, Order No. 540 001 82, for the first time ever, resin primary elements can be produced on varnish-coated dies. This is the perfect basis for milled restorations.

112

Entirely gap-free fit of the Pi-Ku-Plast outer coping allows perfect precision of the secondary elements.

Implant bars can be secured in place rigidly with optimal dimensional stability.

Pi-Ku-Plast HP 36

For accurate, stable and millable resin dies and frameworks.

The competitor’s resin and Pi-Ku-Plast

HP in the incineration test.

At 275°C the competitor’s product foams and expands considerably.

At 300°C the competitor’s product reveals distinctive expansion whereas

Pi-Ku-Plast reduces in volume.

Identical copings produced with brush resin.

The competitor’s resin and Pi-Ku-Plast

HP 36, prepared for investing.

The considerable expansion of the competitor’s resin during the incineration phase resulted in the fracture of the investment material die in the casting ring. After casting, the crown is sealed with a lid and cannot be used. A section through the cast crown shows the fractured die.

Through friction heat during grinding and high heat sensitivity, the plasticity phase of the competitor’s resin can be reached. Deformation of the model, rough grinding surfaces, and inadequate fit may result.

Pi-Ku-Plast features dimensional stability; during grinding fine shavings are obtained and a smooth grinding surface is ensured.

Allow the wax element to cool down to obtain a tension free bridge model. Separate using a thin blade and connect using Pi-Ku-Plast

HP 36.

The extremely low shrinkage of

Pi-Ku-Plast allows to obtain a tension free model and precision fit casting.

Pi-Ku-Plast HP36 Asst. Kit

$189.00

100 ml Monomer

100 ml Cleaner

85 g Polymer

1 Brush size A

1 Brush size B

1 Brush holder

3 Vessels

Transparent Kit

Yellow Kit

Orange Kit

Blue Kit

Red Kit

#540 002 16

#540 002 17

#540 002 18

#540 002 19

#540 002 20

REFILL PACKAGES ITEM #

Transparent Monomer 100 ml

Yellow Monomer 100 ml

Orange Monomer 100 ml

Blue Monomer 100 ml

Red Monomer 100 ml

Polymer 85g

Cleaner 100 ml

Separating Agent 10 ml

3 brushes, Size A + holder

3 brushes, Size B + holder

Vessel for Monomer 8 ml

Vessel for Polymer 8 ml

Vessel for Cleaner 8 ml

#540 002 10

#540 002 11

#540 002 12

#540 002 13

#540 002 14

#540 002 15

#540 002 24

#540 001 82

#330 011 46

#330 011 47

#540 002 07

#540 002 08

#540 002 09

PRICE

$40.00

$40.00

$40.00

$40.00

$40.00

$78.50

$54.00

$27.50

$25.95

$25.95

$12.50

$12.50

$12.50

113

Ropak

Light curing pink opaquer for chrome cobalt frameworks.

Ropak light-curing opaque

10 ml Ropak uv-f liquid

#520 001 64 $32.00

Ropak light-curing opaque

10 g Ropak uv-p powder

#520 001 65 $57.00

The viscosity of Ropak UV can be adjusted to the individual requirements.

Mix powder and liquid on a mixing tray to obtain a homogeneous consistency.

Use disposable brush to apply the material. Ropak UV will coat the object even if it exhibits a thin consistency.

Apply thinly using the disposable brush; even dark metal elements will be coated in an aesthetic way.

Aesthetics beyond compare - pink opaque shows perfection

Light curing liquid opaque for masking chrome cobalt prior to adding the acrylic. Because of its pink color, when the opaque is applied to framework, the chrome cobalt becomes almost invisible inside the acrylic. Cures in less than two minutes.

Tooth-colored UV Opaquer

To enhance aesthetics in the area of acrylic teeth.

Tooth-colored UV Opaquer

10 ml

#540 001 05 $45.50

114

Tooth-colored UV Opaquer is particularly suitable for the anterior area.

The tooth-colored opaque that features a fi ne coating capacity is applied to the desired area.

This way perfect coating of the metal and thus aesthetic restorations are obtained.

Light-curing die spacer, transparent

To smoothen and harden the surface.

Results in dies which are smooth and hard as glass. Light curing die can be applied in the required thickness, thanks to its translucent color. This is the first die spacer which also toughens the die against mechanical loads.

Retention beads and crystals adhere to it extremely well.

Light Curing Die Varnish

Blue, 20 ml

Red, 20 ml

Yellow, 20 ml

Green, 20 ml

#540 010 00 $50.50

#540 010 03 $50.50

#540 010 04 $50.50

#540 010 05 $50.50

Transparent, 20 ml

#540 010 06 $50.50

Five different colors to ensure contrast to any type of modeling wax.

Mixing block

10 pieces

#330 011 44 $49.00

Disposable brush

100 pieces #330 011 42 $25.50

Brush holder straight

12 pieces

#330 011 49 $25.50

Brush holder bent

12 pieces

#330 011 41 $25.50

NEW!

Diephos Dentine Tooth Colored UV Die Spacer

Used when fabricating all ceramic restorations such as veneers or inlays.

Diephos Dentine is a light curing, tooth colored die spacer to be used when fabricating all ceramic restorations such as veneers or inlays. An excellent alternative to blue, green and red die spacers; it prevents the color of the die stone to shine through.

This enhances the visual perception of the dental technician allowing them to create highly aesthetic restorations.

Diephos

10 ml

#540 001 00

$45.00

• Allows accurate shade matching to the patients dentition

• Cures in 90 seconds (under 400nm or greater wavelength of UV light)

• Applies quickly and evenly

• Integrated brush in bottle cap

• Makes die surfaces abrasion resistant

Light curing die spacer, opaque

Swift application due to excellent masking of color.

Die varnish, light-curing, opaque

Blue, 20 ml

Green, 20 ml #540 001 03 $57.95

Red, 20 ml

#540 001 01 $57.95

#540 001 04 $57.95

Light-curing die varnish is available in three different opaque colors. The fine masking capacity allows to obtain a uniform color of the varnish layer.

During the application the die varnish diffuses into the plaster surface. Depth polymerization leads to abrasion resistant bonding to the die. Light curing die varnish resists high mechanical stress. Even steam blasting the units does not affect the strong bonding.

115

Porcelain mixing liquid

• Much less shrinkage thanks to improved condensing properties

• Prevents occlusal and interdental contraction cracks in the porcelain

• Easier to condense

Tip:

Mix the porcelain slightly thinner, to obtain the ideal consistency leave it for two minutes, if building-up takes a long time, stir the mixture from time to time if necessary and add a few drops of porcelain mixing liquid because the porcelain already begins to condense on the mixing slab.

Porcelain mixing liquid

30 ml bottle #520 008 60 $11.50

200 ml bottle #520 001 23 $35.50

Stain liquid

• Provides for an absolutely even glaze

• Holds the stains in place perfectly on porcelain

• Thanks to a new formula, this stain liquid can be used for inlay stains

Stain liquid

7 ml bottle #520 008 40 $23.00

30 ml bottle #520 001 21 $55.50

Plaster Solvent

Readily mixed solution for removing plaster residue from all surfaces.

Plaster Solvent

1 liter

#520 001 19 $24.95

Removing the plaster gently and quickly does not harm the acrylic surface or shade.

Hard plaster is quickly removed, without damaging the mixing bowl.

116

Oxide-Stop for Precious Metals

Prevents polished, precious and semi precious alloy surfaces from oxidizing while being soldered with a flame or in a furnace and while firing porcelain.

• Oxide-Stop Precious forms a protective layer during firing which prevents the metal surface from oxidizing.

Oxide-Stop for Precious Metals

Oxide-Stop Precious, 20 ml

#520 006 50 $47.95

Thinner, 20 ml

#520 006 70 $30.95

Oxide-Stop Precious maintains the high luster.

No refinishing is required.

Refinishing oxidized surfaces reduces the material and may adversely affect the precision of fit.

Oxide-Stop Precious Range of Applications

Oxide-Stop Precious metal crowns and bridges oxidizing during soldering.

Safeguards high grade milled attachment restorations against oxidation while porcelain is being fired.

Perfect for post-soldering porcelain bridgework. The high luster metal surface is protected.

Shake the Oxide-Stop Precious well and brush it onto the areas to be protected. Allow briefly to dry. The surface is now optimally protected against oxidation.

Always apply a fresh coat of Oxide-

Stop Precious after the casting has been heated. Only then is optimum protection of oxidation provided.

After firing or soldering, the protective layer is easily removed with hot water or a steam cleaner.

Refinishing is reduced to a minimum, which saves time and enhances the quality.


Anti-flux agent for soldering and casting.


Used for establishing pre-contact areas when making attachment and telescopic work. This low viscosity, special graphite blend is used to coat inner copings with a thin layer of film in order to localize pre-contacts on the outer copings. Its low viscosity allows this anti-flux to be applied easily to any area, thus preventing wetting or penetration by the solder. Especially suitable for difficult cases. Dilute with water.

20ml #540 007 06 $45.50

117

Silano-Pen

Safe, easy to use, inexpensive bonding system.

Gap-free, reliable chemical bonding of metal/resin, ceramic/resin, resin/resin

Secure bonding system for new acrylic veneers

Gap-free bonding of new acrylic veneers on gold, nonprecious metal and titanium.

Reliable bonding with acrylic veneer repairs

Chemical bonding between acrylic and ceramic

118

Simple preparation of metal frameworks for the repair of damaged veneers.

Outstanding bonding from veneer resins on metal/ceramic transition zones.

Gap-free bonding with....

Cr-Co framework Characterizing Solder free bonding

Full dentures

Reliable bonding of acrylics to chrome cobalt retentions and facings.

Gap-free bonding of acrylic resins to prefabricated acrylic and ceramic teeth.

Pretreatment of bonding surfaces reduces their size due to increased bonding strength.

Processing instructions

Time saving, easy activating of metal frameworks.

For light curing veneering resins.

No discoloring of teeth in denture acrylics due to chemical bonding in cervical areas.

Sand blast the surface with nonrecycled blasting material, 110 mi at 4 bars of pressure. Blow clean with oil and water-free compressed air.

Heat the area to be veneered evenly with the flame for 5 seconds per facing.

Reliable repair of acrylic and ceramic work

After the surface has cooled down (under 50 C o

), apply the bonding agent and let dry for 3 minutes.

Apply and cure opaque and dentine according to the manufacturer’s instructions.

Acrylic, ceramic, metal: Blast with non-recycled blasting material,

110 mi at 4 bars of pressure.

Clean with oil and water free compressed air.

Heat the area to be repaired evenly with the flame.

Ceramic: 5 seconds per veneer

Acrylic: 3 seconds per veneer

After cooling of the flamed area

(under 50 C o

), apply the bonding agent with a brush and let dry for

3 minutes.

If necessary, apply opaque and dentine or only dentine and cure according to the manufacturer’s instructions.

Silano-Pen Assortment Kit

1 Silano-Pen

1 Gas Cartridge*

2 x 2.5 ml Bonding Agent

1 Brush holder, straight

100 disposable brushes

1 Plastic bowl

3 Cleaning brushes

#320 004 70 $765.00

Refill packages

1 Silano-Pen

1 Gas Cartridge*

2.5 ml Bonding Agent

12 Brush holder, straight

100 disposable brushes

12 Plastic bowls

15 Cleaning brushes

#320 004 71

#540 008 30

#540 008 20

#330 011 49

#330 011 42

#230 001 30

#350 004 41

*One gas cartridge is enough for the production of approximately 2000 veneers.

$335.00

$350.00

$78.00

$25.50

$25.50

$12.25

$39.50

119

Heat Absorbent Paste

Heat Absorbent Paste

250 g #540 002 00 $31.50

There is no better method of protecting against heat. This paste will not melt when warmed. Acrylic,

Porcelain, or other heat-sensitive materials are no longer harmed by heat.

Apply the heat absorbent paste very close to the joint.

This paste will not melt when warmed.

Acrylic, porcelain or other heat-sensitive materials are no longer harmed by heat.

Retention Beads and Crystals

Optimum retention leads to the strongest possible acrylic-metal junctures.

Retention adhesive, white - no capillary action, solubilizes the crystals and adheres perfectly as well as having a long working time.

Crystals have double the retentive area of beads.

The beads can be placed singly and positioned accurately with the retention bead applicator.

0.8mm Full Size 10x magnification 10x magnification (gold)

Retention Beads

Retention Beads 0.2 mm #530 020 10




$31.50

0.8mm Full Size

Retention Crystals

Retention Crystals 0.2 mm #530 004 80



$31.50

Retention Adhesive

This new type of retention adhesive prevents any capillary effect when the retention beads are sprinkled onto it.

20 ml bottle #540 007 11 $28.50

20 ml thinner #540 007 12 $22.50

10x magnification 10x magnification (gold)

120

Metal Polishing Set

POLISHING

This introductory set includes everything needed to polish metal from pre-polishing to a high shine.

Abraso Star K80

high abrasion

#520 001 62 $28.50

Abraso Star Glaze

Universal high luster polishing paste for precious metals, non-precious alloys and acrylics.

# 520 001 63 $19.95

Abraso Star K50

low abrasion

#520 001 61 $28.50

Metal Polishing Set

1 Abraso Star K50, low abrasion, 150 g

1 Abraso Star K80, high abrasion, 150 g

1 Abraso Soft Metal

1 Abraso Buff Metal

1 High Luster Buff Metal

1 Pumice Polishing Paste, 500 g

1 Abraso Star Glaze, 50 ml

#350 008 50 $85.00

Pumice Polishing Paste

for polishing acrylic and metal.

1 piece, 500 g

#SP0160

$13.95

Acrylic Polishing Set

Highly recommended for dentist offi ces!

This introductory set includes everything needed to polish acrylic. For an extreme high shine it is recommended to use the Abraso Star Glaze.

Abraso Star K50

low abrasion

#520 001 61 $28.50

Acrylic Polishing Set

1 Abraso Star K50, low abrasion, 150 g

1 Abraso Soft Acrylic

1 Abraso Buff Acrylic

1 High Luster Buff Acrylic

1 Pumice Polishing Paste, 500 g

#350 008 40 $61.50


for polishing acrylic and metal.

1 piece, 500 g #SP0160

$13.95

High Luster Buff Acrylic

#350 008 20 $13.50

Abraso Soft Acrylic

#350 008 00 $12.50

Abraso Buff Acrylic

#350 007 80 $15.50

121


POLISHING

Brushes are shown actual size

The open pore, special nonwoven fabric and bleached bristles absorb more polishing paste due to the heat generated during polishing and reduces the working time by up to 50%.


1 piece

Ø 50 mm

Ø 80 mm

#350 010 20 $12.50

#350 008 00 $12.50

The bristles are bleached. The bleaching roughens and softens the bristles. The rough surface retains the pumice better and polishes the acrylic more actively without harming the surface.

Normal pumice diffuses into the brush and nonwoven fi ber fabric.

The polishing paste is retained there longer and released onto the surface portion by portion.

Due to the combination of nonwoven fi ber fabric and bleached bristles, the pumice polishing paste diffuses deep into the rush.

The open pore structure of the nonwoven fi ber fabric absorbs much more pumice or polishing paste than conventional brushes. The polishing paste no longer has to be applied continually. As the nonwoven fabric absorbs more air it is gentler on the acrylic and the surface remains cooler. The surface is not harmed.


Three rows of high grade bristles and layers of special textile guarantee outstanding results when pre-polishing.


1 piece

Ø 50 mm

Ø 80 mm

#350 010 24 $15.50

#350 007 80 $15.50

The special textile layers retain the polishing paste or normal pumice much longer than conventional brushes. They release abrasives little by little, thus simplifying polishing. This allows the user to work in a relaxed, non-stressed manner.

As the Abraso Buff Acrylic is narrow, it can even be used for polishing in narrow interdental spaces. No need to change the brush.

Once the acrylic has been fi nished

(left), the optimum pre-high luster shown on the right can be achieved quickly and without much effort.

Bleached bristles are harder than goat-hair and softer than black bristles. Bleaching roughens the surface and retains all types of polish better. This simplifi es polishing of acrylics and enables the surface to be conditioned perfectly.

122

POLISHING

Acrylic High-shine Polishing

Brushes are shown actual size

The air is circulated continually to polish acrylic coolly and gently.

This high luster buff is ready for immediate use on a polishing motor and can be used easily and without fraying.

Specially selected fabric prevents the acrylic from overheating.



1 piece

Ø 60 mm, 25 layers

Ø 100 mm, 35 layers

#350 009 40 $15.50

#350 008 20 $12.50

The fi ber reinforced outer layers provide this buff with its previously unheard of stability.

The 35 layers of textile have been welded into place ultrasonically to prevent them from rotating and, due to their high strength, create a perfect highshine.

High Luster Polishing with a Handpiece

Produce a radiant high luster, even in the tiniest areas.

Cotton Buff

15 pieces Metal / Acrylic

Ø 22 mm #350 006 50 $35.00

The loose woven textile circulates the air during high luster polishing and prevents the acrylic from overheating. Therefore, it polishes very gently.

Fluffy, soft cotton fi bers create a mirror like fi nish on soft alloys.

Super soft cotton threads polish palatal rugae optimally and do not leave rough areas which would trap deposits.

123

POLISHING PASTES

Acrypol High Luster Paste

For optimum, abrasive pre-polishing right up to high luster polishing - specially developed polishing pastes enhance the properties of all polishing brushes. This saves time, allows the user to work in a relaxed, non-stressed manner and improves the quality of the work.

Acrypol High Luster

Paste for acrylics and composites

170 g #520 001 70

$21.00

Slightly abrasive material creates a virtually perfect high luster. Simply polishing over the surface with a cotton buff is all that’s needed to produce a perfect high luster.


Great for Dentist Office use!

This long lasting Pumice Paste is used in place of the Pumice + Water mix. It reduces airborne pumice particles that enter the lungs. Cross contamination due to remixing of pumice is eliminated.

Abraso Star

Abraso Star K50 Abraso Star K80

The gentle polishing properties allow all traces left from finishing to be removed from all soft alloys in seconds.

The low abrasion particles of this pumice polishing paste simplify polishing metalacrylic junctures.

Pumice Polishing Paste for polishing metal and acrylics

3 pieces, 500 g each #520 001 60

1 piece, 500 g #SP 0160

$38.00

$13.95

Pumice polishing paste diffuses into the brush and polishes for a very long time.

Abraso Star K80 is highly abrasive, which simplifies polishing all non-precious alloys.

As K50 and K80 stick to all polishing brushes well, abrasive polishing can be carried out longer than when using conventional polishing pastes.

Abraso Star K80

High abrasion, 320 g #520 001 62

Abraso Star K50

Low abrasion, 320 g #520 001 61

$28.50

$28.50

Specially selected raw materials guarantee an absolute mirror-like finish on all dental acrylics.

124

Polishing Pastes

Abraso Star Glaze

Abraso Star Glaze high luster polishing paste for metal, acrylic and composite

50 ml

1 piece

#520 001 63 $19.95

The excellent polishing properties reduce the effort required when polishing with a handpiece.

Abraso Star Glaze creates an optimum high luster quickly and easily.

Diamond Polishing Paste

Polishing paste with a high diamond content and long lasting, impregnated, hard felt wheels provide for the best possible finish on all porcelains.

Great for Dentist Office use!

Extremely long lasting due to pressure impregnation and the hardness.

Diamond Polishing Paste

5 g

#540 001 40 $107.00

Felt wheels

Unmounted, 12 mm Ø

100 pieces

#350 007 10 $82.95

The special consistency of the polishing paste enables it to diffuse into the felt and polish for up to five times longer.

The paste liquefies during polishing and can be pushed backward and forward on the facing without splashing.

Abraso-Fix

Fine abrasive particles integrated into the bristles enable all dental materials to be pre-polished without using polishing paste.

Round Brushes

2 pieces $23.95

Yellow-extrafine

#350 005 80 $23.95

The fine polishing particles create an optimum pre-high luster on all facing acrylics in the shortest possible times.

For: Composites and acrylics.

Red-fine

#350 006 00 $23.95

The soft abrasiveness makes it possible for an exact high luster finish even on secondary attachments.

For: Precious and semi-precious metals.

Round Brushes Assortment Kit

1 round brush yellow

1 round brush red

1 round brush blue

1 round brush green

#350 007 51 $43.95

Blue-regular

#350 005 70 $23.95

The gentle abrasion enables all outer telescopes to be polished to a high luster accurately.

For: Non-precious and hard semiprecious metals.

Green-coarse

#350 005 90 $23.95

Perfect for quickly pre-polishing stippled chrome cobalt denture basis.

For: Chrome cobalt and non-precious metals.

125

Abraso-Fix

Abraso-fix polishers are suitable to pre-polish attachment components such as the VKS ball without the risk of over reducing material.

Abraso fix polishers (when brand new) must be run against a coarse diamond or truing stone in order to expose the abrasive particles. When polishing different materials, Abraso-fix polishers should be cleaned between applications using the aforementioned method.

All surfaces to be polished with Abraso-fix MUST be sandblasted first in order for them to polish properly.

Use elliptical movements and speeds of 10,000 to

15,000 RPM on sandblasted surfaces when polishing with Abraso-fix.

Titanium Finishing

Finishing Titanium rationally using cutters, polishers, brushes and pastes developed specifically for use on Titanium.

Extra-sharp blades, special blade geometry cutter and cutter blades combined with Diatit wear-resistance, which has been proven for many years, guarantee that titanium can be finished quickly without harming the material yet reducing heat development. The titanium Diatitcutter grinds exceptionally abrasively yet runs extremely smoothly on the titanium surface. Thus, one can work accurately and quickly to achieve a uniformly smooth ground surface.

20,000 rpm

#D194 KT 50 $35.90

20-25,000 rpm

#D194 KT 40 $31.00

25-30,000 rpm

#D198 KT 23 $26.90

10-15,000 rpm

#D001 KT 14 $23.00

The cotton polishing buff, for use in a handpiece, and the

Abraso-Star Glaze universal high-luster polishing paste create a fascinating, perfect high luster.

15 pcs. Ø 22mm

#350 006 50 $35.00

Abraso-Star Glaze

50 ml

#520 001 63 $19.95

126

The pre-polishers are matched to titanium to create a uniform, smooth surface on the restoration which can be polished immediately.

Cylinder Bur,

23mm x 6mm Ø

2 pieces #350 008 80 $20.00

Wheel Bur, 3mm x 22mm Ø

2 pieces #350 008 70 $15.50

NEW!

bre.Lux

Polymerization Multi Talent for Practice and Laboratory

To date, several devices were necessary for processing facing and dental materials. With bre.Lux the concept of processing all current materials with one single device becomes reality for the fi rst time.

ENERGY

The bre.Lux Power Unit consists of one LED light polymerization device with 21 power LEDs in 3 different capacities, from 370 nm to 500 nm. The LEDs have a useful life of 20,000 hours.

The bre.Lux LED N manual lamp (with spiral cable) features a capacity ranging from 370 nm to 500 nm. The fl exible hose - with receptacle ring for the manual lamp - serves as a third hand and allows two-handed work.

PERFORMANCE

• Fixation / Hardening / Intermediate polymerization and fi nal thorough hardening directly in the workplace and with one single device

• 370 - 500 nm covers the needed wavelength range, for the manual lamp as well

• Performance delay and reduction minimize the properties and results of dental materials

• Start-up delay and polymerization time can be easily combined

• Large volume for 2 models, optimally and uniformly illuminated

Keyboard layout of the light polymerization device

(1) Display

(2) 20 seconds, 50% power

(3) 40 seconds, 50% power

(4) Continuous operation,

70% power

(5) 90 seconds, full power




(9) Continuous operation,

full power

bre.Lux Power Unit

#140 009 70

$2,400.00

1 polymerization device

1 bre.Lux LED N manual lamp

with spiral cable

1 fl exible hose

1 mains cable

CONSISTENCY

The membrane keyboard already comes with several parameters.

On the left side: Reduced power for the start-up phase with 20 and 40 seconds and for continuous operation at full power as well. The combinations (such as start-up with reduced power) can be combined with the programmed running times of 60 to

360 seconds according to demand.

Example: 40 seconds with reduced power combined with a 180second total running time means the total running time is lowered from 180 to about 40 seconds, and the running time would still be 140 seconds under full power.

Please take note of the application recommendations for

Bredent products.

Keyboard layout for the manual lamp

(1) Continuous operation, start/stop

(2) 15 seconds

(3) 30 seconds

127

COMING SOON visio.lign

The new veneering system

visio.lign has multi-layer novo.lign A veneers for anterior teeth, novo.lign P veneers for posterior teeth and a bonding system in perfectly matched shades.

Additional tooth and gingiva materials complete the system.

Your benefits

• Color is stable and resistant thanks to industrially manufactured veneers

• Esthetic appearance thanks to anatomical shape and layering design

• Reproducible thanks to the use of identical moulds from the planning to the completion stages

• Time-saving and profitable

• Available in the classic A-D shades

• Resistant to plaque and abrasion thanks to complete hardening below 120°C and at a pressure of 250 bars

• Dual-hardening fixation system ensures complete hardening during processing

Discover the wide indication range of visio.lign which will facilitate your daily work routines in the laboratory and support you during the fabrication of esthetic restoration.

From the veneer-up to the definitive restoration

Selecting shade and design

Indication examples

The esthetic try-in supports planning and transferring and...

...is the basis for a perfect wax-up of the framework and guarantees...

...individual restoration according to the patient’s wishes.

Removable restoration on telescopic crowns with novo.lign A

Implant-supported bar restoration with novo.lign veneers

CoCr Clasp restoration in the lower jaw with novo.lign A in the transparent key silicone visio.sil

Screw-retained bar bridge made of biocompatible Bio XS resin.

Stress-free bonding to SKY UVE-

Abutments

128

visio.lign - the system for guaranteed esthetics

For more information call 1.877.328.3965

or visit us at www.xpdent.com

.

COMING SOON

THERMOPRESS 400

The range of biocompatible materials available guarantees a wide and varied application range of the system

bre.crystal

Features long-term stability, provides a dense and smooth surface.

This results in enhanced comfort of wearing full dentures.

• No residual monomer - high biocompatibility

• Limited water absorption - constant suction effect, lasting precision fit

• Available in the shades: crystal clear, pink 1, pink 2, pink 3, pink stippled

• To be processed at 260ºC

bre.dentan

An industrially polymerized thermoplastic resin which increases the resistance to fracture and the biocompatibility of crowns and bridges.

• Three different dentine shades are available

• Can be veneered with conventional C+B resins

• Available in three common dentine shades: A, B, C


bre.flex

Unbreakable denture base material for partial dentures. The indication range also includes splints and sports mouthguards.

• Available in the shades: translucent, pink 1, pink 2, pink 3, tooth shade B


Bio Dentaplast

Clasps and attachments which are normally made of metal can be produced using tooth-colored Bio Dentaplast. The esthetic appearance of teeth at which retaining clasps have been attached is improved.

Additional indications are:

• Crowns and bridges (temporary)

• Telescopic and attachment work

• Tooth-colored clasps

• Shades A1, A2, A3, B2, B3 based on the VITA® shade guide


Bio XS

The high-melting Bio XS features dimensional and thermal stability and is stress-free to simplify the fabrication of precision-fit dentures.

• The extremely stable thermoplastic resin is perfectly suitable for the fabrication of metal-free veneers of corwns and bridges and for telescopic and attachment work.

• Supplied in cream color


For more information call 1.877.328.3965

or visit us at www.xpdent.com

.

129

CUT THIS PAGE OUT AND PHOTOCOPY BEFORE USING

PLEASE FAX ORDERS TO: 786.433.4634

Date: _____________________ Cust. Fax#: _____________________ Cust. PO#: _______________

FROM

Laboratory/Office Name: ___________________________________________ Cust. #___________________

E-Mail: ___________________________________________________________________________________

Contact Name: ____________________________________________ Telephone: _____________________

Street Address: ____________________________________________________________________________

City: __________________________________ State: _________ Zip: ___________________________

Item Number Description Qty Price Extension

(Shipping charges not included. Sales tax applicable to Florida orders.)

Charge to established account

C.O.D. (FedEx charge applies)

Please send a Credit Aplication with my order

Visa/Mastercard

Discover

American Express

Check Enclosed (Order ships when check has cleared)

Wire Transfer

Card Number: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __

Expiration Date: ___ / ___ CID#: _______

(Required for credit card orders)

Print Name: ______________________________

Signature: ________________________________

Total

Shipping Method

FedEx Ground

(4-7 Business Days)

FedEx Express Saver

(3rd Business Day by 4:30 PM)

FedEx 2nd day

(2nd Business Day by 4:30 PM)

FedEx Standard Overnight

(Next Business Day by 4:30 PM)

FedEx Priority Overnight

(Next Business Day by 10:30 AM)

TERMS OF SALE

CONVENIENT PAYMENT OPTIONS:

Establish an “Open Account”:

A completed XPdent credit application must be submitted for approval before an open account can be established.

Open invoices are payable within 30 days from the date of the invoice. (Past due balances are subject to a fi nance charge of 1.5% per month).

Pay by Check, C.O.D. or by Visa, M/C, A/X or Discover.

All orders are payable in U.S. Dollars. Returned checks are subject to a $25.00 charge.

DELIVERY TERMS:

Freight Options:

All orders will be shipped via FedEx Ground.

Special Over-

night, 2nd Day, and 3rd day delivery are available at an additional cost.

Special orders require a 25% non-refundable deposit when order is placed.

Orders placed after 3:30 p.m. will be processed next business day.

• Prices are subject to change without notice.

• XPdent Corp. is not to be held responsible for and reserves the right to correct any misprinted items such as description of product, pricing, product codes, etc.

• No other “Terms of Sale” are in effect as of the October

2009 issue of XPdent’s new catalog.

RETURN POLICY:

Merchandise:

XPdent Corporation reserves the right to correct any defective products, before a return will be considered.

1. Returns are not accepted after 30 days from the date of the invoice.

2. All returns must have prior authorization from XPdent.

To arrange for a return authorization please call us at (877)

328-3965.

3. Return Authorization # issued by XPdent must be on the outside of the package when returning an item. No packages will be accepted without this number.

4. A copy of the invoice must be enclosed with the return. All returns should be sent to:

XPdent RMA # _________

12145 S W 131 Avenue

Miami, FL 33186

5. Items must be returned complete and unused in the original container, unmarked, with seals intact.

All items should be returned unopened.

6. Special ordered items may not be returned for credit or exchange.

7. Absolutely no returns will be accepted on incomplete cards of teeth.

8. Any shortages must be reported within 48 hours of receipt of merchandise.

9. Returns must be sent by traceable carrier (i.e. UPS,

FedEx, etc.)

10. Return freight costs are the responsibility of the customer.

11. Returns not following the above policies will be refused or subject to a restocking charge.

12. Returns meeting all of the above policies receive the appropriate credit or refund.

BUSINESS HOURS (Eastern Time):

MONDAY - THURSDAY 8:30 AM - 6:30 PM

FRIDAY 8:30 AM - 5:00 PM

PLEASE CALL US AT 1-877-328-3965

OR FAX US AT (786) 433-4634

[email protected]

www.xpdent.com

Prices in catalog are subject to change without notice. Not responsible for printing errors.

VKS-SG Attachment System

The sole importer of Bredent products for more than 14 years

Contents

ATTACHMENTS

BRUSHES

LIQUIDS

EQUIPMENT

MATERIALS

MODELS & DUPLICATING

RESINS

TOOLS

WAXES

PONTICS

BURS & DISCS

POLISHINGS

New Br

Koli Brush

- golden brown natural hair

Natural hair brushes made of superior quality Kolinsky hair.

ushes!

Magic Contrast

- black hair

Fatigue-free working thanks to the contrast of the ceramic material and the brush hair. The synthetic hairs provide lasting resiliency of the brush tip.

Koli Brush

- product line

Carefully Selected Hair!

Magic Contrast

- product line

Lasting Resiliency of the Brush Tip!

BREDENT CASE DESIGN IDEAS

The Low Profile

Application of the

Bredent Attachments aids in the stability of your implant case

Production sequence for an implant bar case

Bredent Attachments Requirements for Success:

The following are a list of things needed in order to produce a successful, long-lasting prosthesis using Bredent attachments:

Yellow-Extraﬁne Round Brushes Highly Recommended!

Abraso-Fix Polishers are suitable to pre-polish attachment components without the risk of over reducing material!

If you have any questions on any Bredent attachment case, please contact our technical support team for assistance at:

Bredent USA FREE Case Designer

Use any of the Bredent attachments to digitally construct a case.

Design • Combine • Decide

Bredent Casting Technique Book

“A dental technician’s manual for producing precise ﬁ tting, homogenous and biocompatible dental castings”

The Bredent Casting Technique

Sprues for Centrifugal Casting & Rinsing Heads

Attachment Selector by Indication

VS-3 Mini

> The most widely used attachment in Europe!

> VS-3 Mini offers a gentle slide-in friction with great stability.

> The height can be adjusted up to 40% to fit cases with limited

vertical room.

>“Self cleaning” design prevents the acumulation of plaque and

debris on the attachment which reduces wear and increases

longevity.

> Less maintenance and wear than traditional ball attachments.

> Offers all the benefits of the VS-3 Mini attachments with the

addition of extra support grooves for added stability.

> Eliminates the need for a lingual arm for situations where

metal arms are not desired and aesthetics are a must.

VS-3 Mini Attachment System

VS-3 Mini SV Attachment System

VS-3 Mini Instructions

Minimize the wear factor with the VS-3 Mini Attachment.

VS-3 Mini

VS-3 Mini SV Instructions

Minimize the wear factor with the VS-3 Mini SV Attachment.

VS-3 Mini SV

Dimensions

VKS-SG

> The most versatile Bredent attachment system

> Cost effective and easy to use and maintain

> Available in two ball diameters, each with over 6 retention levels

> Can be used in cases with very limited room

> Retention clips are made of special Duroplast material which resists

deterioration in the oral environment

> Laser welding components also available