UM3057
User manual
Getting started with STEVAL-IFP045V1 industrial digital output expansion board
Introduction
The STEVAL-IFP045V1 is an industrial digital output expansion board. It provides a powerful and flexible environment for the evaluation of the driving and diagnostic capabilities of the IPS1025HQ single high-side smart power solid state relay, in a digital output module connected to 2.5 A industrial loads.
The STEVAL-IFP045V1 can interface with the microcontroller on the STM32 Nucleo via 5 kV optocouplers driven by GPIO pins and Arduino R3 connectors.
The expansion board can be connected to either a NUCLEO-F401RE or a NUCLEO-G431RB development board.
It is also possible to evaluate a system composed of up to four stacked STEVAL-IFP045V1 expansion boards.
As an example, a system with four STEVAL-IFP045V1 expansion boards allows you to evaluate a quad channel digital output module.
Figure 1. STEVAL-IFP045V1 expansion board
UM3057 - Rev 1 - August 2022
For further information contact your local STMicroelectronics sales office.
www.st.com
1
1.1
1.1.1
UM3057
Getting started
Getting started
•
•
•
•
•
•
•
•
•
•
•
Overview
The STEVAL-IFP045V1 embeds the IPS1025HQ intelligent power switch (IPS), featuring overcurrent and overtemperature protection for safe output load control.
The board is designed to meet application requirements in terms of galvanic isolation between user and power interfaces. This requirement is satisfied by an optical isolation implemented through three optocouplers (ISO1,
ISO2, and ISO3) for signal forward to the device and FLT pins for feedback diagnostic signals.
The expansion board features:
• Based on the IPS1025HQ single high-side switch, which features:
– Operating range up to 60 V
– Low-power dissipation (R
ON(MAX)
= 25 mΩ)
– Fast decay for inductive loads
– Smart driving of capacitive loads
– Undervoltage lock-out
– Overload and overtemperature protections
– QFN48L 8x6 mm package
Application board operating range: 8 to 33 V/0 to 2.5 A
Extended voltage operating range (J3 open) up to 60 V
Green LED for output on/off status
Red LEDs for overload and overheating diagnostics
5 kV galvanic isolation
Supply rail reverse polarity protection
Compatible with STM32 Nucleo development boards
Equipped with Arduino UNO R3 connectors
CE certified
RoHS and China RoHS compliant
Not FCC approved for resale
Digital section
The digital section is associated with the STM32 interface and digital supply voltage to and from the STEVAL-
IFP045V1 expansion board.
UM3057 - Rev 1 page 2/19
Figure 2. STEVAL-IFP045V1 expansion board: digital interface section
Dotted green line indicates the whole digital interface section. Pink rectangles identify Arduino UNO R3 connectors
UM3057
Overview
UM3057 - Rev 1
The four Arduino UNO R3 connectors:
•
• allow expansion board communication with the
STM32 peripheral and GPIO resources;
STM32 Nucleo development board microcontroller accessing provide digital supply voltage between the STM32 Nucleo development board and the STEVAL-IFP045V1 expansion board, in either direction.
•
•
Normally, the STM32 Nucleo development board supplies the expansion board by a 3v3 or 5v0 generated by the
USB. You can select the preferred voltage on the expansion board via SW3 (3v3 closing pins 1-2; 5v0 closing pins 2-3).
Alternatively, it is possible to supply the STM32 Nucleo development board by the expansion board. In this case, an external supply voltage (7-12 V) should be connected to CN2 connector (not mounted by default) on the expansion board and the ground loop should be closed by mounting D2 (enabling the reverse polarity protection) or by closing J2 (without reverse polarity).
To supply the V
IN
voltage rail, it is necessary to: close jumper JP5 between pins 2 and 3 and open jumper JP1 on the NUCLEO-F401RE ; open jumper JP5 between pins 1 and 2 and close jumper JP5 between pins 3 and 4 on the NUCLEO-
G431RB .
page 3/19
1.1.2
UM3057
Overview
Power section
The power section involves the power supply voltage (CN1, pins 4 and 5 for V
CC
, pin 3 for GND), load connection (a load can be connected between pins CN1.1 and CN1.3 or CN1.2, and CN1.3; both output pins are connected to the single output channel as shown in Schematic diagrams) and electromagnetic compatibility
(EMC) protection.
Figure 3. STEVAL-IFP045V1 expansion board: power section components
1.
Overtemperature red LED
2.
Overload red LED
3.
IPS1025HQ
4.
Output channel - green LED
5.
Output and power supply connector
UM3057 - Rev 1
2
1
3
4
5
For EMC:
•
•
•
The SM15T39CA transient voltage suppressor (TR1), enabled by closing J3, is placed between V
CC
and
GND tracks to protect the IPS1025HQ against surge discharge on the supply rail path up to ±1 kV/2 Ω coupling; in common mode surge testing, two single-layer capacitors (C1 and C2 - not included) must be soldered at the predisposed locations; the IPS1025HQ output stages do not require additional EMC protections with respect to the IEC61000-4-2,
IEC61000-4-3, IEC61000-4-4, IEC61000-4-5, IEC61000-4-8 standards.
page 4/19
1.2
UM3057
Hardware requirements
Hardware requirements
The STEVAL-IFP045V1 expansion board is designed to be used with the NUCLEO-F401RE or NUCLEO-
G431RB STM32 Nucleo development boards.
To function correctly, the STEVAL-IFP045V1 must be plugged onto the matching Arduino UNO R3 connector pins on the STM32 Nucleo board as shown below.
Figure 4. STEVAL-IFP045V1 and STM32 Nucleo stack
1.3
1.4
•
•
•
•
System requirements
To use the STM32 Nucleo development boards with the STEVAL-IFP045V1 expansion board, you need: a Windows PC/laptop (Windows 7 or above) a type A to mini-B USB cable to connect the STM32 Nucleo board to the PC when using a NUCLEO-
F401RE development board a type A to micro-B USB cable to connect the STM32 Nucleo board to the PC when using a NUCLEO-
G431RB development board the X-CUBE-IPS firmware and software package installed on your PC/laptop
Board setup
Step 1.
Connect the micro-USB or mini/USB cable to your PC to use the STEVAL-IFP045V1 with NUCLEO-
F401RE or NUCLEO-G431RB development board
UM3057 - Rev 1 page 5/19
1.5
UM3057
Multiple board configuration
Step 2.
Download the firmware (.bin) onto the STM32 Nucleo development board microcontroller through
STM32 ST-LINK utility , STM32CubeProgrammer and according to your IDE environment as detailed in the table below.
IAR
EWARM-OUT05_06-
STM32F4xx_Nucleo.bin
Table 1. NUCLEO-F401RE development board supported IDEs - bin files
NUCLEO-F401RE
Keil
MDK-ARM-OUT05_06-
STM32F4xx_Nucleo.bin
STM32CubeIDE
STM32CubeIDE-OUT05_06-
STM32F4xx_Nucleo.bin
IAR
EWARM-OUT05_06-
STM32G4xx_Nucleo.bin
Table 2. NUCLEO-G431RB development board supported IDEs - bin files
NUCLEO-G431RB
Keil
MDK-ARM-OUT05_06-
STM32G4xx_Nucleo.bin
STM32CubeIDE
STM32CubeIDE-OUT05_06-
STM32G4xx_Nucleo.bin
Step 3.
Connect the IPS1025HQ device supply voltage via CN1 (see
Section 1.1.2 Power section ).
Step 4.
Provide the digital supply voltage (see
Section 1.1.1 Digital section
).
Step 5.
Connect the load on the output connector (see Section 1.1.2 Power section
).
Step 6.
Reset the example sequence using the black push button.
Step 7.
Push the STM32 Nucleo blue button to select the example provided in the firmware package.
Multiple board configuration
It is also possible to evaluate a four channel digital output module by stacking four STEVAL-IFP045V1 with shared or independent supply rail and independent loads.
In this case, the four expansion boards (board 0, 1, 2, 3 as shown in the table below) must be properly configured: for board 1, 2 and 3, it is necessary to unsolder three resistors for each board from the default position and solder them back in the alternate positions according to the following table.
Board 0
Board 1
Board 2
Board 3
Board no.
Table 3. Configuration of a stack of four expansion boards
IN1 FLT1
R101
R102
R115
R120
R103
R104
R116
R119
R114
R117
R107
R118
FLT2
UM3057 - Rev 1 page 6/19
2 Schematic diagrams
15
17
19
21
23
25
27
11
13
7
9
1
3
5
29
31
33
35
37
CN7
N.M.
16
18
20
22
24
26
28
2
4
6
8
10
12
14
30
32
34
36
38
SSQ-119-04-L-D
CN6
6
7
4
5
1
2
3
8
I OREF
NRST
3V3
5V
VIN
SSQ-108-04-F-S
3v3 5v0
Figure 5. STEVAL-IFP045V1 circuit schematic (1 of 2)
Morpho Connectors
(N.M.)
15
17
19
21
23
25
27
11
13
7
9
1
3
5
29
31
33
35
37
CN10
N.M.
16
18
20
22
24
26
28
2
4
6
8
10
12
14
30
32
34
36
38
SSQ-119-04-L-D
OUT1
VCC
C6
+ C10
100uF
N.M.
2.2uF
J4 default open
D1 STPS1H100A
Analog supply
8V - 60 V
J3
TR1 TP4
5001
EARTH
C1
4700pF
N.M.
default closed
C2
4700pF
N.M.
3
4
5
1
2
CN1
OUT
OUT
GND
VCC
VCC
691137710005
ALTERNATE USE
DEFAULT
FLT1
FLT1
ALTERNATE USE
ALTERNATE USE
DEFAULT
ALTERNATE USE
ALTERNATE USE
FLT1
IN1
IN1
IN1
IN1
R104
R103
R119
R120
R101
R102
R115
100 N.M.
100
100 N.M.
100 N.M.
100
100 N.M.
100 N.M.
D13
D12
D11
D10
D9
D8
D15
D14
AVDD
PB8
PB9
PA5
PA6
PA7
PB6
PC7
PA9
6
5
4
3
2
1
10
9
8
7
CN5
SSQ-110-04-F-S
VIN
TP2
5001
Alternate Nucleo Supply
7V - 12 V
(7V-12V NUCLEO supply voltage)
TR2 N.M.
ESDA15P60-1U1M
D2 N.M.
BAT48JFILM
J2 default open
2
1
CN2
N.M.
691214110002
CN8
5
6
3
4
1
2
PA0
PA1
PA4
PB0
PC1
PC0
A0
A1
A2
A3
A4
A5
R118
R114
R107
SSQ-106-04-F-S
100 N.M.
100
100 N.M.
FLT2
FLT2
FLT2
ALTERNATE USE
DEFAULT
ALTERNATE USE
ALTERNATE USE FLT1
ALTERNATE USE FLT2
Arduino Connectors
R116
R117
CN9
100 N.M.
100 N.M.
D7
D6
D5
D4
D3
D2
D1
D0
PA8
PB10
PB4
PB5
PB3
PA10
PA2
PA3
8
7
6
5
4
3
2
1
SSQ-108-04-F-S
MH1
M3 HOLE NOT PLATED
MH2
M3 HOLE NOT PLATED
MH3
M3 HOLE NOT PLATED
MH4
M3 HOLE NOT PLATED
FIDUCIAL1
Fiducial
FIDUCIAL2
Fiducial
IN1
FLT1
FLT2
FIDUCIAL3 FIDUCIAL4
Fiducial Fiducial
IN1
FLT1
FLT2
VCC
IN1
ISO1
J5 default closed
R2
390
R1
27K
J6 default closed
R12
22k
TP1
5001
FLT1
SW2 con3-strip-male default: CLOSE 1-2
Figure 6. STEVAL-IFP045V1 circuit schematic (2 of 2)
2
SW1 con3-strip-male
3
1 default: CLOSE 1-2
J9 con6-2x3-strip-male
R710k
R8
10k
R11
2.2K
ISO2
R10
0
DR1
R9
0
J7
TP3
5001
C4
0.1uF
C5
0.1uF
49
Exp-VCC
J8 default: closed
U1
IPS1025HQ
GND
6
OUT1
J1 default closed
TP5
5001
3v3
5v0
1
3
SW3
2 con3-strip-male default: CLOSE 1-2
FLT2
R6 2.2K
SW4 con3-strip-male default: CLOSE 1-2
ISO3
R5
0
DR2
R4
0
R3
22k
DG1
3
UM3057
Bill of materials
Bill of materials
Item Q.ty
Ref.
1
2
5
6
3
4
7
8
9
10
11
12
13
14
15
16
0
2
1
1
1
1
0
1
0
1
1
1
2
0
0
1
C1 C2
C6
C7
C8
C9
C4 C5
C10
CN1
CN2
CN5
CN6 CN9
CN7 CN10
CN8
D1
D2
DG1
Part/value
4700pF 1825
(4564 Metric)
3000V (3kV)
10%
0.1uF 0805
(2012 Metric)
100V 10%
2.2uF 1206
(3216 Metric)
100V 10%
470pF 0603
(1608 Metric)
50V 5%
47nF 0603
(1608 Metric)
50V 10%
470nF 0603
(1608 Metric)
25V 10%
-
100uF Radial,
Can 100V 20%
691137710005
691214110002
7.4X7 pitch 3.5
TH 2.54mm
TH 2.54mm
TH 2.54mm
STPS1H100A,
SMA
BAT48JFILM,
SOD323
150060GS7500
0 0603 (1608
Metric) 20mA
Description Manufacturer Order code
CAP CER
4700PF 3KV
X7R 1825 (not mounted)
CAP CER
0.1UF 100V
X7R 0805
CAP CER
2.2UF 100V
X7R 1206
CAP CER
470PF 50V
C0G/NP0 0603
CAP CER
0.047UF 50V
X7R 0603
CAP CER
0.47UF 25V
X7R 0603
CAP 100 UF
20% 100 V (not mounted)
TERM BLK
5POS SIDE
ENTRY 5MM
PCB
TERM BLK
2POS SIDE
ENT 3.5MM
PCB (not mounted)
100 V, 1 A power Schottky rectifier
40 V, 350 mA axial general purpose signal
Schottky diode
(not mounted)
LED GREEN
CLEAR 0603
SMD
Vishay Vitramon HV1825Y472KXHATHV
Würth
Elektronik
AVX
Corporation
Wurth
Electronics Inc.
Murata
Electronics
North America
Wurth
Electronics Inc.
Würth
Elektronik
Würth
Elektronik
Wurth
Electronics Inc.
10 ways, 1 row
8 ways, 1 row
CONN RCPT
38POS 0.1
GOLD PCB (not mounted)
-
6 ways, 1 row
Samtec Inc.
4UCONN
Samtec Inc.
4UCONN
Samtec Inc.
4UCONN
ST
ST
Wurth
Electronics Inc.
-
885012207128
12061C225KAT2A
885012006061
GCM188R71H473KA55D
885012206075
860130878011
691137710005
691214110002
ESQ-110-14-T-S 17896
ESQ-108-14-T-S 15782
ESQ-106-04-T-S 15781
STPS1H100A
BAT48JFILM
150060GS75000
UM3057 - Rev 1 page 9/19
UM3057 - Rev 1
UM3057
Bill of materials
17
18
19
20
21
22
23
24
25
26
26
28
29
30
31
32
Item
2
3
7
0
1
1
1
2
4
2
2
3
0
4
5
1
Q.ty
Ref.
DR1 DR2
ISO1 ISO2
ISO3
J1 J2 J3 J4 J5
J6 J8
J7
J9
R1
R2
R3 R12
R4 R5 R9 R10
R6 R11
R7 R8
R101 R103
R114
Part/value
150060RS7500
0 0603 (1608
Metric) 20mA
140109146000
LSOP04
JUMPER-con2strip-male TH
2.54mm
JUMPER-con2strip-male con6-2x3-stripmale
27K 0603 (1608
Metric) 0.1W,
1/10W 1%
390 0603 (1608
Metric) 0.1W,
1/10W 1%
22k 0603 (1608
Metric) 0.1W,
1/10W 1%
0 0603 (1608
Metric) 0.1W,
1/10W Jumper
2.2K 0603
(1608 Metric)
0.1W, 1/10W
1%
10k 0603 (1608
Metric) 0.1W,
1/10W 1%
100 0603 (1608
Metric) 0.1W,
1/10W 1%
Description
LED RED
CLEAR 0603
SMD
OPTOISO 5KV
TRANSISTOR
JUMPER-
CONN
HEADER .100
STR 2POS
JUMPER-
CONN
HEADER .100
STR 2POS (not mounted)
CONN
HEADER .100
DUAL STR
6POS
RES SMD 27K
OHM 1% 1/10W
0603
RES SMD 390
OHM 1% 1/10W
0603
RES SMD 22K
OHM 1% 1/10W
0603
RES SMD 0
OHM JUMPER
1/10W 0603
RES SMD 2.2K
OHM 1% 1/10W
0603
-
Manufacturer
Wurth
Electronics Inc.
Wurth
Electronics Inc.
Wurth
Electronics Inc.
Wurth
Electronics Inc.
Yageo
Yageo
Yageo
Panasonic
Electronic
Components
Yageo
RES SMD 10K
OHM 1% 1/10W
0603
Yageo
RES SMD 100
OHM 1% 1/10W
0603
Yageo
R102 R104
R107 R115
R116 R117
R118 R119
R120
100 0603 (1608
Metric) 0.1W,
1/10W 1%
RES SMD 100
OHM 1% 1/10W
0603 (not mounted)
SW1 SW2 SW3
SW4
TP1 TP2 TP3
TP4 TP5
TR1 con3-strip-male
TH 2.54mm
CONN
HEADER .100
STR 3POS
5001 0.100" Dia x 0.180" L
(2.54mm x
4.57mm)
SM15T39CA,
SMC
TEST POINT
PC MINI .040"D
BLACK
1500 W, 33.3 V
TVS in SMC
Yageo
Wurth
Electronics Inc.
Keystone
Electronics
ST
-
Order code
150060RS75000
140109146000
61300211121
61300621121
RC0603FR-0727KL
RC0603FR-07390RL
RC0603FR-0722KL
ERJ-3GEY0R00V
RC0603FR-072K2L
RC0603FR-0710KL
RC0603FR-07100RP
RC0603FR-07100RP
61300311121
5001
SM15T39CA page 10/19
34
35
33
Item Q.ty
0 TR2
Ref.
1
12
U1
N/A
UM3057
Bill of materials
Part/value Description
ESDA15P60-1U
1M, QFN-2L
High-power transient voltage suppressor (not mounted)
IPS1025HQ
QFN48L 8x6 mm
High Side
Switch with smart driving for capacitive loads
Manufacturer
ST
ST
2.54mm
Close Jumper
Wurth
Electronics Inc.
Order code
ESDA15P60-1U1M
IPS1025HQ
60900213421
UM3057 - Rev 1 page 11/19
4 References
Freely available on www.st.com
:
1.
IPS1025H datasheet
2.
UM2864: "Getting started with X-CUBE-OUT5 industrial digital output software for STM32 Nucleo"
3.
NUCLEO-F401RE data brief
4.
NUCLEO-G431RB data brief
UM3057
References
UM3057 - Rev 1 page 12/19
5
UM3057
Board versions
Board versions
Table 4. STEVAL-IFP045V1 versions
PCB version
STEVAL$IFP045V1A (1)
Schematic diagrams
STEVAL$IFP045V1A schematic diagrams
Bill of materials
STEVAL$IFP045V1A bill of materials
1. This code identifies the STEVAL-IFP045V1 evaluation board first version. It is printed on the board PCB.
UM3057 - Rev 1 page 13/19
6
UM3057
Regulatory compliance information
Regulatory compliance information
Notice for US Federal Communication Commission (FCC)
For evaluation only; not FCC approved for resale
FCC NOTICE - This kit is designed to allow:
(1) Product developers to evaluate electronic components, circuitry, or software associated with the kit to determine whether to incorporate such items in a finished product and
(2) Software developers to write software applications for use with the end product.
This kit is not a finished product and when assembled may not be resold or otherwise marketed unless all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of an FCC license holder or must secure an experimental authorization under part 5 of this chapter 3.1.2.
Notice for Innovation, Science and Economic Development Canada (ISED)
For evaluation purposes only. This kit generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to Industry Canada (IC) rules.
À des fins d'évaluation uniquement. Ce kit génère, utilise et peut émettre de l'énergie radiofréquence et n'a pas
été testé pour sa conformité aux limites des appareils informatiques conformément aux règles d'Industrie Canada
(IC).
Notice for the European Union
This device is in conformity with the essential requirements of the Directive 2014/30/EU (EMC) and of the
Directive 2015/863/EU (RoHS).
Notice for the United Kingdom
This device is in compliance with the UK Electromagnetic Compatibility Regulations 2016 (UK S.I. 2016 No. 1091) and with the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment
Regulations 2012 (UK S.I. 2012 No. 3032).
UM3057 - Rev 1 page 14/19
Revision history
Date
2 9 Aug -2022
Table 5. Document revision history
Revision
1 Initial release.
Changes
UM3057
UM3057 - Rev 1 page 15/19
UM3057
Contents
Contents
1 Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
1.1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1.1
Digital section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1.2
Power section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2
Hardware requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.3
System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.4
Board setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.5
Multiple board configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 Schematic diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
3 Bill of materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
5 Board versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
6 Regulatory compliance information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
List of tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
List of figures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
UM3057 - Rev 1 page 16/19
UM3057
List of tables
List of tables
Table 1. NUCLEO-F401RE development board supported IDEs - bin files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Table 2. NUCLEO-G431RB development board supported IDEs - bin files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Table 3. Configuration of a stack of four expansion boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Table 4. STEVAL-IFP045V1 versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Table 5. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
UM3057 - Rev 1 page 17/19
UM3057
List of figures
List of figures
Figure 1. STEVAL-IFP045V1 expansion board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Figure 2. STEVAL-IFP045V1 expansion board: digital interface section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Figure 3. STEVAL-IFP045V1 expansion board: power section components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Figure 4. STEVAL-IFP045V1 and STM32 Nucleo stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Figure 5. STEVAL-IFP045V1 circuit schematic (1 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 6. STEVAL-IFP045V1 circuit schematic (2 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
UM3057 - Rev 1 page 18/19
UM3057
IMPORTANT NOTICE – READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgment.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, refer to www.st.com/trademarks . All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2022 STMicroelectronics – All rights reserved
UM3057 - Rev 1 page 19/19
