STMicroelectronics X-NUCLEO-OUT12A1 industrial digital output expansion board for STM32 Nucleo User Manual
STMicroelectronics X-NUCLEO-OUT12A1 industrial digital output expansion board for STM32 Nucleo provides a powerful and versatile platform to evaluate the ISO808A octal high-side smart power solid state relay. With embedded galvanic isolation and 20MHz SPI control interface, this expansion board enables safe output load control in industrial applications. The X-NUCLEO-OUT12A1 is compatible with STM32 Nucleo development boards and features Arduino® UNO R3 connectors for easy interfacing.
Advertisement
Advertisement
UM3080
User manual
Getting started with the X-NUCLEO-OUT12A1 industrial digital output expansion board for STM32 Nucleo
Introduction
The X-NUCLEO-OUT12A1 is an industrial digital output expansion board for STM32 Nucleo . It provides a powerful and flexible environment for the evaluation of the driving and diagnostic capabilities of the ISO808A octal high-side smart power solid state relay, with embedded galvanic isolation and 20MHz SPI control interface, in a digital output module connected to 0.7 A industrial loads.
The X-NUCLEO-OUT12A1 directly interfaces with the microcontroller on the STM32 Nucleo driven by GPIO pins and Arduino
®
R3 connectors.
The galvanic isolation between the microcontroller and the process stage is guaranteed by the ISO808A .
The expansion board can be connected to either a NUCLEO-F401RE or a NUCLEO-G431RB development board.
It is also possible to evaluate a 16 channel digital output system enabling the daisy chaining feature on two X-NUCLEO-
OUT12A1 stacked expansion boards.
Figure 1. X-NUCLEO-OUT12A1 expansion board
UM3080 - Rev 1 - December 2022
For further information contact your local STMicroelectronics sales office.
www.st.com
1
1.1
UM3080
Getting started
Getting started
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Overview
The X-NUCLEO-OUT12A1 embeds the ISO808A intelligent power switch (IPS), which features galvanic isolation,
20 MHz SPI and Power Good diagnostic, overcurrent and overtemperature protection for safe output loads control.
The board is designed to meet the application requirements for the galvanic isolation between the user and power interfaces.
The galvanic isolation embedded by the ISO808A satisfies this requirement, avoiding the necessity of external optocouplers, with a consequent cost saving and a reduced application size.
The expansion board features:
–
–
Based on the ISO808A octal high-side switch, which features:
–
–
–
Operating range 9.2 to 36 V
Low power dissipation (R
ON(MAX)
= 260 mΩ)
Process side operating current: up to 0.7 A per channel
Embedded 2k V
RMS
galvanic isolation
PGOOD (VCC voltage level alarm signalization)
–
–
–
–
–
–
20 MHz SPI with daisy chaining
Fast decay for inductive loads
Undervoltage lock-out
Overload and overtemperature protections
Loss of ground protection
PowerSO36 package
Application board process side operating range: 10 (J10 open) to 33 V (J9 closed)
Extended operating range of process side from 9.2 (J10 closed) up to 36 V (J9 open)
Application board logic side operating voltage 3.3 to 5 V
Green LEDs for outputs on/off status (J6 and J7 close 1-2, 3-4, 5-6, 7-8)
Red LED for common overheating and communication error diagnostic (J3 close 1-2)
Red LED for PGOOD signalization (J3 close 3-4)
Yellow LED for output enable status signalization (J3 close 5-6)
Process and logic supply rails reverse polarity protections
Compatible with STM32 Nucleo development boards
Equipped with Arduino ® UNO R3 connectors
RoHS and China RoHS compliant
CE certified
Radiated emission: class B according to the standard EN 55032
UM3080 - Rev 1 page 2/19
1.2
UM3080
Digital section
Digital section
The digital section is associated with the STM32 interface and the digital supply voltage to and from the
X-NUCLEO-OUT12A1 expansion board.
Figure 2. X-NUCLEO-OUT12A1 expansion board: digital interface section
UM3080 - Rev 1
The dotted green line indicates the whole digital interface section. The pink rectangles identify the Arduino® UNO
R3 connectors.
The four Arduino® UNO R3 connectors:
•
• allow the expansion board to communicate with the STM32 Nucleo development board microcontroller accessing the STM32 peripheral and GPIO resources; provide the digital supply voltage between the STM32 Nucleo development board and the X-NUCLEO-
OUT12A1 expansion board, in either direction.
Usually, the STM32 Nucleo development board supplies the expansion board by a 3.3 V or 5.0 V generated by the USB.
Alternatively, it is possible to supply the STM32 Nucleo development board by the expansion board. In this case, an external supply voltage (7-12 V) should be connected to the CN11 connector (not mounted by default) on the expansion board and the ground loop should be closed by mounting D2 (enabling the reverse polarity protection) or by closing J5 (without reverse polarity). In this scenario, the logic side of the ISO808A can be supplied by the
3.3 V supply rail generated by the expansion board: in this case, on the X-NUCLEO-OUT12A1 , J4 must be closed between pins 5 and 6.
To supply the VIN voltage rail, it is necessary to:
•
• close the JP5 jumper between pins 2 and 3 and open the JP1 jumper on the NUCLEO-F401RE ; open the JP5 jumper between pins 1 and 2 and close the JP5 jumper between pins 3 and 4 on the
NUCLEO-G431RB .
The pin 3 of the connector CN11 can be used to supply the logic side of the ISO808A independently by the expansion board. In this case, on the X-NUCLEO-OUT12A1 , the pins 1 and 2 of J4 must be closed (pins 5-6 open).
page 3/19
1.3
UM3080
Power section
4.
5.
6.
1.
2.
3.
Power section
The power section involves the power supply voltage (CN1, pin 1 for V
CC
, pin 2 for GND), the load connection
(eight loads can be connected between each pin of CN2, CN3, CN4, and CN12 and pin 2 of CN1), EMC protections (U2), and supply reverse polarity protection (D1).
Figure 3. X-NUCLEO-OUT12A1 expansion board: power section components
ISO808A
Output and power supply connector
Output channels - green LEDs
Status (overtemperature) red LED
Output Enable yellow LED
Power Good - red LED
UM3080 - Rev 1
For EMC:
•
•
• the SM15T39CA transient voltage suppressor (U2), enabled by closing J9, is placed between V
CC
and
GND tracks to protect the ISO808A against surge discharge on the supply rail path up to ±1 kV/2 Ω coupling; in the common mode surge testing, two single-layer capacitors (C11 and C12 - not included) must be soldered at the predisposed locations; the ISO808A output stages do not require additional EMC protections with respect to the IEC61000-4-2,
IEC61000-4-3, IEC61000-4-4, IEC61000-4-5, IEC61000-4-8 standards.
The EMC performance of the X-NUCLEO-OUT12A1 is detailed below:
• for emission (when the DC input port of the board is powered by an AC-DC, DC-DC or battery with a cable that does not exceed a three-meter length), compliance with standards:
•
–
–
–
–
EN IEC 61000-6-3:2021
EN 55032:2015 +A1:2020 for immunity, compliance with standards:
EN IEC 61000-6-1:2019
EN 55035:2017 +A11:2020 page 4/19
1.4
UM3080
Hardware requirements
Hardware requirements
The X-NUCLEO-OUT12A1 expansion board is designed to be used with the NUCLEO-F401RE or NUCLEO-
G431RB STM32 Nucleo development boards.
To function correctly, the X-NUCLEO-OUT12A1 must be plugged onto the matching Arduino ® UNO R3 connector pins on the STM32 Nucleo board as shown below.
Figure 4. X-NUCLEO-OUT12A1 and STM32 Nucleo stack
1.5
System requirements
To use the STM32 Nucleo development boards with the X-NUCLEO-OUT12A1 expansion board, you need:
•
• a Windows PC/laptop (Windows 7 or above) a type A to mini-B USB cable to connect the STM32 Nucleo board to the PC when using a NUCLEO-
F401RE development board
•
• a type A to micro-B USB cable to connect the STM32 Nucleo board to the PC when using a NUCLEO-
G431RB development board the X-CUBE-IPS firmware and software package installed on your PC/laptop
UM3080 - Rev 1 page 5/19
1.6
UM3080
Board setup
Board setup
Step 1.
Connect the mini-USB or micro-USB cable to your PC to use the X-NUCLEO-OUT12A1 with NUCLEO-
F401RE or NUCLEO-G431RB development board
Step 2.
Download the firmware (.bin) onto the STM32 Nucleo development board microcontroller through
STM32 ST-LINK utility , STM32CubeProgrammer , and according to your IDE environment as detailed in the table below.
IAR
EWARM-OUT12_14-
STM32F4xx_Nucleo.bin
Table 1. NUCLEO-F401RE development board supported IDEs - bin files
NUCLEO-F401RE
Keil
MDK-ARM-OUT12_14-
STM32F4xx_Nucleo.bin
STM32CubeIDE
STM32CubeIDE-OUT12_14-
STM32F4xx_Nucleo.bin
IAR
EWARM-OUT12_14-
STM32G4xx_Nucleo.bin
Table 2. NUCLEO-G431RB development board supported IDEs - bin files
NUCLEO-G431RB
Keil
MDK-ARM-OUT12_14-
STM32G4xx_Nucleo.bin
STM32CubeIDE
STM32CubeIDE-OUT12_14-
STM32G4xx_Nucleo.bin
Note:
–
–
–
By default, the X-NUCLEO-OUT12A1 is configured to work stand-alone. However, it is possible to stack two X-NUCLEO-OUT12A1 and enable the related control by enabling the daisy chaining communication:
Close J12 [1-2] and J13 [3-4 ] in board #1
Close J12 [3-4] and J13 [1-2 ] in board #2
Rework board #1: remove R105 and mount R102
– Rework board #2: remove R119, R108, R107, R104 and mount R102, R113, R111, R109
In terms of software, it is necessary to generate the new binary file after having defined the preprocessor directive USE_DAISY_CHAIN and removed the directive USE_PAR_IND (or changed in noUSE_PAR_IND). The modification to control mode becomes effective on the binary files after rebuilding.
Step 3.
Connect the ISO808A device supply voltage via CN1 (see
).
Step 4.
Provide the digital supply voltage (see
Section 1.2 Digital section ).
Step 5.
Connect the load on the output connector (see Section 1.3 Power section ).
Step 6.
Reset the example sequence by pushing the black button on the STM32 Nucleo board.
Step 7.
Push the blue button on the STM32 Nucleo board to choose among the examples provided in the default firmware package.
UM3080 - Rev 1 page 6/19
2 Schematic diagrams
CN6
7
8
5
6
3
4
1
2
SSQ-108-04-F-S
I OREF
NRST
3V3
5V
VIN
3v3 5v0
CN8
3
4
1
2
5
6
PA0
PA1
PA4
PB0
PC1
PC0
SSQ-106-04-F-S
R120
R119
R118
R117
R116
R115
21
23
25
27
11
13
15
17
19
29
31
33
35
37
1
7
9
3
5
CN7
22
24
26
28
12
14
16
18
20
30
32
34
36
38
2
4
6
8
10
SSQ-119-04-L-D
N.M.
Figure 5. X-NUCLEO-OUT12A1 circuit schematic (1 of 2)
Morpho connectors
(not mounted)
21
23
25
27
11
13
15
17
19
29
31
33
35
37
1
7
9
3
5
CN10
22
24
26
28
12
14
16
18
20
30
32
34
36
38
2
4
6
8
10
SSQ-119-04-L-D
N.M.
VCC
+ C9
47uF
N.M.
C10
2.2uF
J10 default open
D1 STPS1H100A
Analog supply
10-36 V
1
2
CN1
691214110002
J9
U2 C11
4700pF
N.M.
TP8
5001 EARTH
C12
4700pF
N.M.
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
OUT8
691214110002
2
1
2
CN2
691214110002
1
2
1
CN3
691214110002
2
1
CN4
691214110002
CN12
100 N.M.
100
100 N.M.
100 N.M.
100 N.M.
100 N.M.
PGOOD
OUT_EN
SPI_SS
DaisyChain
STATUS
OUT_EN
Al t er nat e use
DEFAULT
Al t er nat e use
Al t er nat e use
Al t er nat e use
Al t er nat e use
DEFAULT
DEFAULT
STATUS
PGOOD
DEFAULT
DEFAULT
DEFAULT
DEFAULT
Al t er nat e use
Al t er nat e use
SPI_CLK
SPI_MISO
SPI_MOSI
SPI_SS
DaisyChain
DaisyChain
R108
R107
R106
R105
R104
R103
R102
R101
Al t er nat e use
Al t er nat e use
Al t er nat e use
Al t er nat e use
SPI_SS
STATUS
DaisyChain
PGOOD
Al t er nat e use OUT_EN
R114
R113
R112
R111
R109
100
100
100
100
100
100
100 N.M.
100 N.M.
100 N.M.
100 N.M.
100 N.M.
100 N.M.
100 N.M.
PB8
PB9
AVDD
10
9
8
7
PA5
PA6
PA7
PB6
PC7
PA9
6
5
4
3
2
1
CN5
SSQ-110-04-F-S
CN9
PA8
PB10
PB4
PB5
PB3
PA10
PA2
PA3
8
7
6
5
4
3
2
1
SSQ-108-04-F-S
EXT_Vdd
I SO808A di r ect suppl y vol t age:
- set t o max 3. 3V when X- NUCLEO- OUT12A1 i s usded wi t h NUCLEO boar d
- can be set t o max 5. 5V when X- NUCLEO- OUT12A1 i s used st and- al one
D2
D12
ESDA7P60-1U1M
N.M.
N.M.
691214110003
3
2
1
BAT48JFILM
N.M.
CN11
J5 N.M. default open
U3
ESDA15P60-1U1M
N.M.
JUMPER-con2-strip-male
VIN
( 7V- 12V NUCLEO suppl y vol t age)
SPI_CLK
SPI_MISO
SPI_MOSI
SPI_SS
PGOOD
DaisyChain
STATUS
OUT_EN
SPI_CLK
SPI_MISO
SPI_MOSI
SPI_SS
PGOOD
DaisyChain
STATUS
OUT_EN
Arduino connectors
D11
RED LED
R15
1k
OUT_EN
SPI_SS
SPI_CLK
SPI_MOSI
PGOOD
SPI_MISO
Dais yChain
R121
1k
D16
RED LED
R17
390
EXT_Vdd
3v3
D15
LED YELLOW
SPI_MOSI
Dais yChain
1
3
J 12
SPI_MISO
Dais yChain default: clos e 1-2
2
4
1
3 con4-2x2-s trip-male
J 13 default: clos e 1-2
2
4 con4-2x2-s trip-male
Figure 6. X-NUCLEO-OUT12A1 circuit schematic (2 of 2)
1
3
5
J 3 default: clos e 1-2, 3-4, 5-6
2
4
6 con6-2x3-s trip-male
1
3
5
J 4 default: clos e 5-6
2
4
6 con6-2x3-s trip-male
C25
2.2uF
C26
0.1uF
D13
SMBJ 5.0A-TR
R8 390
R1
R9
R10
R11
390
390
390
390
R2 0
10
11
8
9
12
13
14
15
16
17
18
5
6
7
3
4
1
2
U1
NC1
Vdd
OUT_EN
SS
CLK
SDI
PGOOD
NC8
NC9
NC10
NC11
NC12
SDO
FAULT
GNDdd
NC16
NC17
NC18
VCC_EP
OUT1_1
OUT1_2
OUT2_1
OUT2_2
OUT3_1
OUT3_2
OUT4_1
OUT4_2
OUT5_1
OUT5_2
OUT6_1
OUT6_2
OUT7_1
OUT7_2
OUT8_1
OUT8_2
NC20
GNDcc
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
C13
0.1uF
ISO808A
R3 0
STATUS
C1
C2
VCC
10nF
10nF
C3 10nF
C4 10nF
C5
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
OUT8
10nF
C6 10nF
C7 10nF
C8 10nF
J 6 con8-2x4-s trip-male default clos e: 1-2, 3-4, 5-6, 7-8
J 7 con8-2x4-s trip-male default clos e: 1-2, 3-4, 5-6, 7-8
R25
15k
R26
15k
R27
15k
R28
15k
R29
15k
R30
15k
R18
15k
R19
15k
D3 D4 D5 D6 D7 D8 D9 D10
3
UM3080
Bill of materials
Bill of materials
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Item
8
0
1
0
2
5
1
5
1
2
0
1
0
1
0
Q.ty
C1 C2 C3 C4
C5 C6 C7 C8
C9
C10
C11 C12
C13 C26
C14 C21 C22
C23 C24
C25
CN1 CN2 CN3
CN4 CN12
CN5
CN6 CN9
CN7 CN10
CN8
CN11
D1
D2
Ref.
Table 3. X-NUCLEO-OUT12A1 bill of materials
Part/value
10nF 0603
(1608 Metric)
50V 10%
47uF Radial,
Can 100V 20%
2.2uF 1206
(3216 Metric)
100V 10%
4700pF 1825
(4564 Metric)
3000V (3kV)
10%
0.1uF 0805
(2012 Metric)
100V 10%
33pF 0402
(1005 Metric)
10V 5%
2.2uF 0402
(1005 Metric)
10V 20%
691214110002
7.4X7 pitch 3.5
10 ways, 1 row
8 ways, 1row
6 ways, 1 row
691214110003
10.5X7.4 pitch
3.5mm
STPS1H100A
DO-214AC,
SMA 1A
BAT48JFILM
SC-76,
SOD-323
750mV @
200mA 350mA
(DC)
CAPACITOR
CERAMIC SMD
0402
CAP CER
2.2UF 10V X5R
0402
TERM BLK
2POS SIDE
ENT 3.5MM
PCB
CONN RCPT
10POS 0.1
GOLD PCB
CONN RCPT
8POS 0.1
GOLD PCB
CONN RCPT
38POS 0.1
GOLD PCB (not mounted)
CONN RCPT
6POS 0.1
GOLD PCB
TERM BLK
3POS SIDE
ENT 3.5MM
PCB (not mounted)
DIODE
SCHOTTKY
100V 1A SMA
Description
CAP CER
10000PF 50V
X7R 0603
CAP 47 UF
20% 100 V (not mounted)
CAP CER
2.2UF 100V
X7R 1206
CAP CER
4700PF 3KV
X7R 1825 (not mounted)
CAP CER
0.1UF 100V
X7R 0805
Manufacturer
Wurth
Electronics Inc.
Wurth
Electronics Inc.
AVX
Corporation
Wurth
Electronics Inc.
Wurth
Electronics Inc.
Wurth
Electronics Inc.
Wurth
Electronics Inc.
SAMTEC
4UCON
SAMTEC
4UCON
Samtec Inc.
SAMTEC
4UCON
Wurth
Electronics Inc.
ST
Order code
885382206002
860040875002
12061C225KAT2A
Vishay Vitramon HV1825Y472KXHATHV
885012207128
885012005010
885012105013
691214110002
ESQ-110-14-T-S 17896
ESQ-108-14-T-S 15782
SSQ-119-04-L-D
ESQ-106-04-T-S 15781
691214110003
STPS1H100A
DIODE
SCHOTTKY
40V 350MA
SOD323 (not mounted)
ST BAT48JFILM
UM3080 - Rev 1 page 9/19
UM3080 - Rev 1
UM3080
Bill of materials
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Item
8
2
0
1
1
1
1
0
2
2
2
5
2
2
1
2
Q.ty
Ref.
D3 D4 D5 D6
D7 D8 D9 D10
D11 D16
D12
D13
D15
J3
J4
J5
J6 J7
J9 J10
J12 J13
R1 R8 R9 R10
R11
R2 R3
R14 R20
R17
R15 R121
Part/value
LED GREEN
0603 (1608
Metric) 20mA
RED LED 0603
(1608 Metric)
20mA
Description
LED GREEN
CLEAR 0603
SMD
LED RED
CLEAR 0603
SMD
ESDA7P60-1U1
M 2-UDFN
TVS DIODE
5VWM 11.6VCL
1610 (not mounted)
SMBJ5.0A-TR
DO-214AA,
SMB 600W
LED YELLOW
0603 (1608
Metric) 20mA
TVS DIODE 5V
13.4V SMB con6-2x3-stripmale con6-2x3-stripmale
JUMPER-con2strip-male con8-2x4-stripmale
JUMPER-con2strip-male con4-2x2-stripmale
390 0402 (1005
Metric) 0.1W,
1/10W 5%
0 0402 (1005
Metric) 0.1W,
1/10W 0%
Manufacturer
Wurth
Electronics Inc.
Wurth
Electronics Inc.
ST
ST
LED YELLOW
CLEAR 0603
SMD
CONN
HEADER .100
DUAL STR
6POS
CONN
HEADER .100
DUAL STR
6POS
JUMPER-
CONN
HEADER .100
STR 2POS (not mounted)
CONN
HEADER VERT
8POS 2.54MM
JUMPER-
CONN
HEADER .100
STR 2POS
CONN
HEADER .100
DUAL STR
4POS
CHIP
RESISTOR
SMD 5% 1/10W
0402
CHIP
RESISTOR
SMD 0% 1/10W
0402
RES SMD 22K
OHM 1% 1/10W
0603
Wurth
Electronics Inc.
Wurth
Electronics Inc.
Wurth
Electronics Inc.
Wurth
Electronics Inc.
Wurth
Electronics Inc.
Wurth
Electronics Inc.
Wurth
Electronics Inc.
Panasonic
Panasonic
Yageo
22k 0603 (1608
Metric) 0.1W,
1/10W 1%
390 0603 (1608
Metric) 0.1W,
1/10W 1%
1k 0603 (1608
Metric) 0.1W,
1/10W 1%
RES SMD 390
OHM 1% 1/10W
0603
RES SMD 1K
OHM 1% 1/10W
0603
Yageo
Yageo
Order code
150060VS75000
150060RS75000
ESDA7P60-1U1M
SMBJ5.0A-TR
150060YS75000
61300621121
61300621121
61300211121
61300821121
61300211121
61300421121
ERJH2GJ391X
ERJH2G0R00X
RC0603FR-0722KL
RC0603FR-07390RL
RC0603FR-071KL page 10/19
UM3080 - Rev 1
UM3080
Bill of materials
32
33
34
35
36
37
38
39
Item
8
0
7
1
1
1
16
0
Q.ty
Ref.
R18 R19 R25
R26 R27 R28
R29 R30
R101 R102
R109 R111
R112 R113
R114 R115
R116 R117
R118 R120
R103 R104
R105 R106
R107 R108
R119
Part/value
15k 0603 (1608
Metric) 0.1W,
1/10W 1%
Description
RES SMD 15K
OHM 1% 1/10W
0603
Manufacturer
Yageo
100 0603 (1608
Metric) 0.1W,
1/10W 1%
RES SMD 100
OHM 1% 1/10W
0603
Yageo
Order code
RC0603FR-0715KL
RC0603FR-07100RP
TP8
U1
U2
N/A
U3
100 0603 (1608
Metric) 0.1W,
1/10W 1%
RES SMD 100
OHM 1% 1/10W
0603
Yageo RC0603FR-07100RP
5001 0.100" Dia x 0.180" L
(2.54mm x
4.57mm)
TEST POINT
PC MINI .040"D
BLACK
ISO808ATR
PowerSO-36
Galvanic isolated octal high side smart power solid state relay with
SPI interface
SM15T39CA
DO-214AB,
SMC 1500W
(1.5kW)
TVS DIODE
33.3V 69.7V
SMC
Keystone
Electronics
ST
ST
2.54mm
Close Jumper
Wurth
Electronics Inc.
ESDA15P60-1U
1M 2-UDFN
TVS DIODE
13.2V 22.7V
1610
ST
5001
ISO808ATR
SM15T39CA
60900213421
ESDA15P60-1U1M page 11/19
4
UM3080
Board versions
Board versions
Table 4. X-NUCLEO-OUT12A1 versions
Finished good
X$NUCLEO-OUT12A1
Schematic diagrams
X$NUCLEO-OUT12A1 schematic diagrams
1. This code identifies the X-NUCLEO-OUT12A1 evaluation board first version.
Bill of materials
X$NUCLEO-OUT12A1 bill of materials
UM3080 - Rev 1 page 12/19
5
UM3080
Regulatory compliance information
Regulatory compliance information
Notice for US Federal Communication Commission (FCC)
For evaluation only; not FCC approved for resale
FCC NOTICE - This kit is designed to allow:
(1) Product developers to evaluate electronic components, circuitry, or software associated with the kit to determine whether to incorporate such items in a finished product and
(2) Software developers to write software applications for use with the end product.
This kit is not a finished product and when assembled may not be resold or otherwise marketed unless all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of an FCC license holder or must secure an experimental authorization under part 5 of this chapter 3.1.2.
Notice for Innovation, Science and Economic Development Canada (ISED)
For evaluation purposes only. This kit generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to Industry Canada (IC) rules.
À des fins d'évaluation uniquement. Ce kit génère, utilise et peut émettre de l'énergie radiofréquence et n'a pas
été testé pour sa conformité aux limites des appareils informatiques conformément aux règles d'Industrie Canada
(IC).
Notice for the European Union
This device is in conformity with the essential requirements of the Directive 2014/30/EU (EMC) and of the
Directive 2015/863/EU (RoHS).
Notice for the United Kingdom
This device is in compliance with the UK Electromagnetic Compatibility Regulations 2016 (UK S.I. 2016 No. 1091) and with the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment
Regulations 2012 (UK S.I. 2012 No. 3032).
UM3080 - Rev 1 page 13/19
6 References
Freely available on www.st.com
:
•
•
•
•
ISO808A datasheet
UM3035: "Getting started with X-CUBE-IPS industrial digital output software for STM32 Nucleo"
NUCLEO-F401RE documentation
NUCLEO-G431RB documentation
UM3080
References
UM3080 - Rev 1 page 14/19
Revision history
Date
19-Dec-2022
Table 5. Document revision history
Revision
1 Initial release.
Changes
UM3080
UM3080 - Rev 1 page 15/19
UM3080
Contents
Contents
UM3080 - Rev 1 page 16/19
UM3080
List of tables
List of tables
UM3080 - Rev 1 page 17/19
UM3080
List of figures
List of figures
UM3080 - Rev 1 page 18/19
UM3080
IMPORTANT NOTICE – READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgment.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, refer to www.st.com/trademarks . All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2022 STMicroelectronics – All rights reserved
UM3080 - Rev 1 page 19/19
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement