Stamina Owner`s Manual

Product May Vary Slightly From Pictured.

CAUTION:

Weight on this product should not exceed 300 lbs.

This Product is Distributed Exclusively by

Owner's

Manual

!

WARNING

Exercise can present a h e a l t h r i s k . C o n s u l t a physician before beginning any exercise program with this equipment. If you feel faint or dizzy, immediately discontinue use of this equipment. Serious bodily injury can occur if this equipment is not assembled and used correctly. Serious bodily injury can also occur if all instructions are not followed. Keep others and pets away from equipment when in use. Always make sure all bolts and nuts are securely tightened prior to each use. Follow all safety instructions in this manual.

When calling for parts or service, please specify the following number :

Model#: 15-1100A

2040 N. Alliance, Springfield, MO 65803

Customer Service

1 (800) 375-7520

www.staminaproducts.com

STAMINA PRODUCTS

MADE IN CHINA

©

2011 Stamina Products, Inc.

2011, 11

TABLE OF CONTENTS

Safety Instructions ...................................... 2

Before You Begin ........................................ 4

Equipment Warning, Caution & Notice Labels ... 5

Hardware Identification Chart .................... 6

Assembly Instructions ................................ 7

Set Up Instructions ................................... 13

Operational Instructions ........................... 14

Storage ....................................................... 16

Maintenance ............................................... 16

Conditioning Guidelines ........................... 17

Warm-Up and Cool-Down ......................... 18

Warranty ..................................................... 19

Product Parts Drawing .............................. 20

Parts List .................................................... 21

Fax/Mail Ordering Form ............................ 23

SAFETY INSTRUCTIONS

!

!

!

WARNING This product contains a chemical known to the State of California to cause cancer and birth defects or other reproductive harm.

WARNING Consult your physician before starting this or any exercise program. This is especially important if you are over the age of 35, have never exercised before, are pregnant, or suffer from any health problem. This product is for home use only. Do not use in institutional or commercial applications. Failure to follow

WARNING all warnings and instructions could result in serious injury or death.

To reduce the risk of serious injury, read the following Safety Instructions before using the Airgometer 1100.

1. Read all warnings and cautions posted on the

Airgometer 1100.

2. The

Airgometer 1100 should only be used after a thorough review of the Owner’s Manual.

3. We recommend that two people be available for assembly of this product.

4. Keep children away from the Airgometer 1100. Do not allow children to use or play on the Airgometer

1100. Keep children and pets away from the Airgometer 1100 when it is in use.

5. The Airgometer 1100 is not a freewheeling exercise bike; therefore, pedal speed should be reduced in a controlled manner to prevent injury from spinning pedals.

6. Remain seated while pedaling the Airgometer 1100. Failure to do so could result in serious injury.

7. It is recommended that you place this exercise equipment on an equipment mat.

8. Set up and operate the Airgometer 1100 on a solid level surface. Do not position the Airgometer 1100 on loose rugs or uneven surfaces.

9. Make sure that adequate space is available for access to and around the


10. Adjust the LEVELING CAPS(73) on the Rear Stabilizer so that the bike sits on the floor without rocking.

11. Before using, inspect Airgometer 1100 for worn or loose components, and securely tighten or replace any worn or loose components prior to use.

12. Before getting on the Airgometer 1100, always check the SEAT POST(4), PEDALS(55, 56), REST

PEDALS(62, 63), and HANDLEBARS(6, 7) to be sure they are secure. The ADJUSTMENT KNOB(72) must be inserted into one of the holes in the SEAT POST(4) and securely tightened.

13. Each user should adjust the seat per instructions on page 14.

14. Do not attempt to adjust the seat while you are on the


15. Consult a physician prior to commencing an exercise program and follow his/her recommendations in developing your fitness program. If at any time during exercise you feel faint, dizzy, or experience pain, stop and consult your physician.

16. Always choose the workout which best fits your physical strength and flexibility level. Know your limits and train within them. Always use common sense when exercising.

17. Do not wear loose or dangling clothing while using the


18. Never exercise in bare feet or socks; always wear proper footwear such as running, walking, or cross training shoes that fit well, provide foot support, and feature non-skid rubber soles.

19. Be careful to maintain your balance while using, mounting, dismounting, or assembling the

Airgometer

1100, loss of balance may result in a fall and serious bodily injury.

20. The Airgometer 1100 should not be used by persons weighing over 300 pounds.

21. The

Airgometer 1100 should be used by only one person at a time.

22. The Airgometer 1100 is for consumer use only. It is not for use in public or semipublic facilities.

2

Call Us First

1

Customer Service

(800) 375-7520


THANK YOU FOR PURCHASING THE

Airgometer 1100

To enact your warranty, please register your product by going to register.staminaproducts.com

To help you get started, we have pre-assembled most of your

Airgometer 1100 at the factory with the exception of those few parts left unassembled for shipping purposes.

Simply follow the few assembly instructions set forth in this manual.

With regular workouts, you will be getting your body into shape and be on your way to achieving a happier and healthier lifestyle.

Should you have any questions, please call our Customer Service Department toll-free number,

1 (800) 375-7520

Monday - Thursday, 7:30 A.M. - 5:00 P.M., Central Time.

Friday, 8:00 A.M. - 3:00 P.M., Central Time.

ONLINE

CUSTOMER SERVICE [email protected]


TELEPHONE

CUSTOMER SERVICE

Tel: 1 (800) 375-7520

3

FAX


Fax: (417) 889-8064

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071

Springfield, MO. 65801-1071

BEFORE YOU BEGIN

Thank you for choosing the Airgometer 1100.

We take great pride in producing this quality product and hope it will provide many hours of quality exercise to make you feel better, look better, and enjoy life to its fullest.

It's a proven fact that a regular exercise program can improve your physical and mental health.

Too often, our busy lifestyles limit our time and opportunity to exercise. The

Airgometer 1100 provides a convenient and simple method to begin your assault on getting your body in shape and achieving a happier and healthier lifestyle.

Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled.

Read this manual carefully before using the


Although Stamina constructs its products with the finest materials and uses the highest standards of manufacturing and quality control, there can sometimes be missing parts or incorrectly sized parts. If you have any questions or problems with the parts included with your Airgometer 1100, please do not return the product. Contact us

FIRST!

If a part is missing or defective, please go to staminaproducts.com to the Services section and order the part needed, or call us toll free at 1-800-

375-7520 (in the U.S.). Our Customer Service Staff is available to assist you from 7:30 A.M. to 5:00 P.M.

(Central Time) Monday through Thursday and 8:00

A.M. to 3:00 P.M. (Central Time) on Friday.

Be sure to have the name and model number of the product available when you contact us.

Left Handlebar

Water Bottle

Left Rest Pedal

Adjustment Knob

Meter

Right Handlebar

Meter Post

Seat

Seat Post

Main Frame

Right Cover

Leveling Cap

Rear Stabilizer

Warning Label

Linkage

Right Crank

Right Pedal

Right Fan Cage

Right Rest Pedal

Wheel

Endcap

Front Stabilizer

THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY :

Socket Wrench

Allen Wrench w/ Screwdriver (6mm)

4

Large Wrench

Wrench

EQUIPMENT WARNING, CAUTION & NOTICE LABELS

This chart is provided to help identify the warning, caution, and notice labels on the

Airgometer

1100. Please take a moment to familiarize yourself with all of the warning, caution, and notice labels.

Label is larger than actual size

W1 WARNING LABEL(99)

5

HARDWARE IDENTIFICATION CHART

This chart is provided to help identify the hardware used in the assembly process. Place the washers or the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to check the length of the bolts and screws.

3/16" 1/4" 5/16" 3/8" 1/2"

INCHES

0 1/2 1 1/2 2 1/2 3 1/2 4 1/2 5 1/2 6 in.

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 mm.

MILLIMETERS

6 8 10 12

NOTICE: The length of all bolts and screws, except those with flat heads, is measured from below the head to the end of the bolt or screw. Flat head bolts and screws are measured from the top of the head to the end of the bolt or screw.

length length

After unpacking the unit, open the hardware bag and make sure that you have all the following items.

Some hardware may be already attached to the part.

Part Number and Description

45 Tooth Lock Washer (M10)

Qty

2

46 Left Flange Nut, Brass Color (M10 x 1.25, Left Hand Threads) 1

47 Right Flange Nut, Black Color (M10x1.25, Right Hand Threads) 1

49 Wavy Washer (ø17 x ø22 x 0.4mm) 2

80 Carriage Bolt (M8 x 1.25 x 75mm)

85 Screw, Round Head (M5 x 15mm)

87 Bolt, Button Head (M8 x 1.25 x 15mm)

4

2

4

94 Acorn Nut (M8 x 1.25)

97 Arc Washer (M8)

60 Washer (ø16.2 x ø22 x 1.5mm)

61 Washer (ø10 x ø25.4 x 2mm)

96 Washer (M8)

92 Nylock Nut (M8x1.25)

98 Lock Washer (M8)

58 Plastic Washer (ø10 x ø18 x 2mm)

6

4

6

2

2

8

6

8

4

ASSEMBLY INSTRUCTIONS

Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all packing materials from your area and place them back into the box. Do not dispose of the packing materials until assembly is completed. Read each step carefully before beginning. If you are missing a part, please go to staminaproducts.com to the Services section and order the part needed, e-mail us at [email protected], or call us toll free at 1-800-375-7520 (in the U.S.). Our

Customer Service Staff is available to assist you from 7:30 A.M. to 5:00 P.M. (Central Time) Monday through Thursday and 8:00 A.M. to 3:00 P.M. (Central Time) on Friday.

STEP 1

Position the FRONT STABILIZER(3) with the R mark on the right side so the WHEELS(76) face the front.

Attach the FRONT STABILIZER(3) to the MAIN FRAME(1) with CARRIAGE BOLTS(M8x1.25x75mm)

(80), ARC WASHERS(M8)(97), LOCK WASHERS(M8)(98), and ACORN NUTS(M8x1.25)(94).

STEP 2

Attach the REAR STABILIZER(2) to the MAIN FRAME(1) with CARRIAGE BOLTS(M8x1.25x75mm)(80),

ARC WASHERS(M8)(97), LOCK WASHERS(M8)(98), and ACORN NUTS(M8x1.25)(94).

NOTE: You can adjust the LEVELING CAPS(73) on the REAR STABILIZER(2) to keep the Airgometer

1100 stable.

R

7


STEP 3

Connect the

CONNECTION WIRE(38) to the SENSOR WIRE(39). Insert the METER POST(5) onto the

MAIN FRAME(1) and secure with BUTTON HEAD BOLTS(M8x1.25x15mm)(87), WASHERS(M8)(96),

ARC WASHERS(M8)(97), and LOCK WASHERS(M8)(98).

STEP 4

Attach the WATER BOTTLE HOLDER(78) to the METER POST(5) with ROUND HEAD SCREWS

(M5x15mm)(85).

8


WARNING:

The SMALL CRANKS(44) require a special tool to remove once assembled. Read all of the following ASSEMBLY INSTRUCTIONS before attaching the SMALL CRANK(44).

NOTE:

1. Align the ARROW MARK on the SMALL CRANK(44) with the WHITE MARK on the AXLE(9) when installing the two SMALL CRANKS(44) onto the AXLE(9). Refer to inset drawing A.

2. The RIGHT FLANGE NUT(M10x1.25)(47), black color, has right hand threads and is tightened by turning clockwise. The LEFT FLANGE NUT(M10x1.25)(46), brass color, has left hand threads and is tightened by turning counterclockwise.

3. There is an “L” decal on the LEFT CRANK(53), and an “R” decal on the RIGHT CRANK(54).

STEP 5

To assemble the RIGHT CRANK(54), install the SMALL CRANK(44) onto the AXLE(9) with TOOTH LOCK

WASHER(M10)(45) and RIGHT FLANGE NUT(M10x1.25)(47). SECURELY TIGHTEN the RIGHT FLANGE

NUT(M10x1.25)(47) with the socket wrench. Push the CRANK CAP(48) into the SMALL CRANK(44).

CAUTION:

It is possible to assemble the LEFT CRANK(53) and the RIGHT CRANK(54) the wrong way as shown in inset drawings B and C. The SMALL CRANK(44) on the LEFT CRANK(53) must be assembled in the opposite direction from the right side. Refer to the below illustration. Use the same procedure as above to assemble the

LEFT CRANK(53).

B.

White Mark

A.

Arrow Mark

C.

L

R

Socket Wrench

9


STEP 6

Bolt the HANDLEBAR SHAFTS(69) to the MAIN FRAME(1) on both sides and securely tighten.

STEP 7

Slide the WASHER(ø16.2xø22x1.5mm)(60) onto the HANDLEBAR SHAFT(69). Slide the RIGHT

HANDLEBAR(7) onto the HANDLEBAR SHAFT(69) in approximately the center of the sliding range.

Place the PLASTIC WASHER(ø10xø18x2mm)(58) on the SHAFT on the lower end of the RIGHT

HANDLEBAR(7). Connect the right LINKAGE(8) to the RIGHT HANDLEBAR(7), then slide the RIGHT

HANDLEBAR(7) completely onto the HANDLEBAR SHAFT(69). Secure the right LINKAGE(8) with the

PLASTIC WASHER(ø10xø18x2mm)(58), WASHER(M8)(96), and NYLOCK NUT(M8x1.25)(92). Repeat on other side.

Shaft

10

Shaft


STEP 8

There is an “L” mark on the bottom side of the LEFT REST PEDAL(62), and an “R” mark on the bottom side of the

RIGHT REST PEDAL(63).

Attach the RIGHT REST PEDAL(63) to the HANDLEBAR SHAFT(69) in the RIGHT HANDLEBAR(7) with WAVY WASHER(ø17xø22x0.4mm)(49), WASHER(ø10xø25.4x2mm)(61), and the SHAFT

BOLT(65). Press the PEDAL COVER(64) into the RIGHT REST PEDAL(63). Repeat on other side.

STEP 9

NOTE: The RIGHT PEDAL(56) has R stamped on the end of the pedal shaft. The RIGHT PEDAL(56) has right hand threads and is tightened by turning clockwise. The LEFT PEDAL(55) has L stamped on the end of the pedal shaft. The LEFT PEDAL(55) has left hand threads and is tightened by turning counterclockwise.

Thread the

RIGHT PEDAL(56) into the RIGHT CRANK(54) as shown. Tighten the pedal securely.

Repeat on the left side to attach the LEFT PEDAL(55) to the LEFT CRANK(53).

L

R

11


STEP 10

Attach the SEAT(70) to the SEAT POST(4) with NYLOCK NUTS(M8x1.25)(92) and WASHERS(M8)(96).

Insert the SEAT POST(4) into the MAIN FRAME(1) and secure with the ADJUSTMENT KNOB(72).

NOTE: The pin of the ADJUSTMENT KNOB(72) must be inserted into one of the adjustment holes in the

SEAT POST(4) and the ADJUSTMENT KNOB(72) must be screwed in tight to ensure that the

SEAT POST(4) will fit securely in the MAIN FRAME(1).

STEP 11

Install two AA batteries into the METER(37), the batteries are not included. See page 15 for detailed battery installation instructions. Plug the

CONNECTION WIRE(38) into the METER(37), and push the excess wires back into the METER POST(5). Slide the METER(37) onto the plate on the METER

POST(5). Be careful not to damage the wires when attaching the METER(37).

STEP 12

Place the WATER BOTTLE(79) in the WATER BOTTLE HOLDER(78).

12

SET UP INSTRUCTIONS

Place the Airgometer 1100 in the area where it will be used. It is recommended that the Airgometer 1100 be placed on an equipment mat. The Airgometer 1100 is approximately 48 inches long x 24.6 inches wide x 52 inches tall. An area 4 feet wide x 6 feet long is required for safe operation of the Airgometer 1100.

Make sure that adequate space is available for access to and passage around the


LEVELING: Adjust the LEVELING CAPS(73) on the REAR STABILIZER(2) so that the Airgometer

1100 sits on the floor without rocking.

MOVING: The Airgometer 1100 has a pair of WHEELS(76) on the FRONT STABILIZER(3). Lift up the REAR STABILIZER(2) to move the Airgometer 1100.

Equipment Mat

FUNCTION INSPECTION:

Visually inspect the Airgometer 1100 to verify that assembly is as shown in the above illustration. Check the function of the Airgometer 1100 by turning the crank slowly through one complete revolution to verify that the drive train functions properly.

CAUTION: Locate and read the WARNING LABEL(99) on the Airgometer 1100. Make sure that all users read the WARNING LABEL(99) before using the product.

13

OPERATIONAL INSTRUCTIONS

SEAT HEIGHT ADJUSTMENT

Proper seat height is important for efficient exercise. To determine proper seat height, sit on the

Airgometer

1100 and center the ball of your foot on the pedal in the down position. Your leg should be slightly bent and relaxed as shown.

If your leg is too straight or if your foot cannot touch the pedal when extended at the downstroke, you will need to lower the seat. If your leg is bent too much, you will need to raise the seat.

Loosen and pull the

ADJUSTMENT KNOB(72), then lower or raise the SEAT(70) to the desired height, and secure with the

ADJUSTMENT KNOB(72). Make all adjustments to seat height while off of the bike.

NOTE: The pin of the ADJUSTMENT KNOB(72) must be inserted into one of the adjustment holes in the

SEAT POST(4). and the ADJUSTMENT KNOB(72) must be screwed in tight to ensure that the

SEAT POST(4) will fit securely in the MAIN FRAME(1).

14

OPERATIONAL INSTRUCTIONS

USING THE FITNESS METER

POWER ON:

POWER OFF:

Pedal movement or press the

MODE button.

Automatic shut off after four minutes of inactivity.

FUNCTION BUTTONS:

MODE :

Press and release to select functions for display or to preset target values.

SET :

Press to set target values for TIME, DISTANCE , and CALORIE.

RESET :

This button will reset each function to zero.

To reset all functions to zero, press the button and hold it down for four seconds.

SPEED INDICATOR:

When pedaling, the LCD will display a bar to show the approximate current speed.

MODE

PRESET VALUES OPERATION:

Stop pedaling for four seconds. When “STOP” appears on display the meter is in setting mode. The meter will cycle through the functions as follows and allow you to set the function values.

Time (0:00 to 99:00) Distance (0.0 to 99.99 mile) Calorie (0.0 to 999.9 Kcal)

Use SET and RESET buttons to choose desired setting values, and press MODE button to confirm. Or, just press the MODE button to skip the setting and move on to the next function. After all the desired settings are chosen, begin pedaling to start the workout.

FUNCTIONS:

SCAN:

TIME:

SPEED:

DISTANCE:

CALORIE:

Automatically scans TIME, SPEED, DISTANCE, and CALORIE in sequence with a change every four seconds. Press and release the

MODE button until “SCAN” appears on display.

Press MODE button until “TMR” appears to display the time from one second up to 99:59 minutes.

Counts down from preset value.

Press MODE button until “SPD” appears to display the current speed from zero to 999.9 miles per hour.

Press MODE button until “DST” appears to display the distance from zero to 99.99 miles. Counts down from preset value.

Press MODE button until “CAL” appears to display the calorie consumption from zero to 999.9 Kcal.

Counts down from preset value.

The calorie readout is an estimate for an average user. It should be used only as a comparison between workouts on this unit.

NOTE:

The meter will shut off automatically after four minutes of inactivity. All function values will be kept.

Press the RESET button and hold it down for four seconds to reset all functions to zero.

AA Batteries

HOW TO INSTALL AND REPLACE BATTERIES:

1. Open the Battery Door on the back of the meter.

2. The meter operates with two AA batteries, the batteries are not included. Refer to the illustration to install or replace the batteries.

NOTE:

1. Do not mix a new battery with an old battery.

2. Use the same type of battery. Do not mix an alkaline battery with another type of battery.

3. Rechargeable batteries are not recommended.

15

STORAGE

1. To store the Airgometer 1100, simply keep it in a clean dry place.

2. The

Airgometer 1100 is approximately 48 inches long x 24.6 inches wide x 52 inches tall. These dimensions may vary. Please measure your Airgometer 1100 if exact dimensions are needed.

3. To move the Airgometer 1100, lift the REAR STABILIZER(2) and use the WHEELS(76) on the FRONT

STABILIZER(3).

4. To avoid damage to the electronics, remove the batteries before storing the Airgometer 1100 for one year or more.

MAINTENANCE

The safety and integrity designed into the Airgometer 1100 can only be maintained when the

Airgometer 1100 is regularly examined for damage and wear. Special attention should be given to the following:

1. Pedaling slowly and verify that the Air Resistance System provides tension. The Air Resistance

System should provide many years of use.

2. Use a wrench to verify that the pedals are tightened securely. If tightening is required, remember that the left pedal has left hand threads and is tightened by turning counterclockwise.

3. Verify that all nuts and bolts are present and properly tightened. Replace missing nuts and bolts.

Tighten loose nuts and bolts.

4. Verify that the WARNING LABEL(99) is in place and easy to read. Call Stamina Products immediately at 1-800-375-7520 for a replacement WARNING LABEL(99) if it is missing or damaged.

5. It is the sole responsibility of the user/owner to ensure that regular maintenance is performed.

6. Worn or damaged components shall be replaced immediately or the Airgometer 1100 removed from service until repair is made.

7. Only Stamina Products supplied components shall be used to maintain/repair the


8. Keep your Airgometer 1100 clean by wiping it off with an absorbent cloth after use.

16

CONDITIONING GUIDELINES

How you begin your exercise program depends on your physical condition. If you have been inactive for several years or are severely overweight, start slowly and increase your workout time gradually. Increase your workout intensity gradually by monitoring your heart rate while you exercise.

Remember to follow these essentials:

Have your doctor review your training and diet programs.

Begin your training program slowly with realistic goals that have been set by you and your physician.

Warm up before you exercise and cool down after you work out.

Take your pulse periodically during your workout and strive to stay within a range of 60% (lower intensity) to 90% (higher intensity) of your maximum heart rate zone. Start at the lower intensity, and build up to higher intensity as you become more aerobically fit.

If you feel dizzy or lightheaded you should slow down or stop exercising.

Initially you may only be able to exercise within your target zone for a few minutes; however, your aerobic capacity will improve over the next six to eight weeks. It is important to pace yourself while you exercise so you don't tire too quickly.

To determine if you are working out at the correct intensity, use a heart rate monitor or use the table below. For effective aerobic exercise, your heart rate should be maintained at a level between 60% and 90% of your maximum heart rate. If just starting an exercise program, work out at the low end of your target heart rate zone. As your aerobic capacity improves, gradually increase the intensity of your workout by increasing your heart rate.

Measure your heart rate periodically during your workout by stopping the exercise but continuing to move your legs or walk around. Place two or three fingers on your wrist and take a six second heartbeat count. Multiply the results by ten to find your heart rate. For example, if your six second heartbeat count is 14, your heart rate is 140 beats per minute. A six second count is used because your heart rate will drop rapidly when you stop exercising. Adjust the intensity of your exercise until your heart rate is at the proper level.

wrist pulse

Target Heart Rate Zone Estimated by Age*

Age

20 years

25 years

30 years

35 years

40 years

45 years

50 years

55 years

60 years

65 years

70 years

Target Heart Rate Zone

(55%-90% of Maximum Heart Rate)

110-180 beats per minute











Average Maximum

Heart Rate 100%

200 beats per minute











* For cardiorespiratory training benefits, the American College of Sports Medicine recommends working out within a heart rate range of 55% to 90% of maximum heart rate. To predict the maximum heart rate, the following formula was used: 220 - Age = predicted maximum heart rate

17

WARM-UP and COOL-DOWN

Warm-Up

The purpose of warming up is to prepare your body for exercise and to minimize injuries.

Warm up for two to five minutes before strength training or aerobic exercising. Perform activities that raise your heart rate and warm the working muscles. Activities may include brisk walking, jogging, jumping jacks, jump rope, and running in place

Stretching

Stretching while your muscles are warm after a proper warm-up and again after your strength or aerobic training session is very important. Muscles stretch more easily at these times because of their elevated temperature, which greatly reduces the risk of injury. Stretches should be held for 15 to 30 seconds. Do not bounce.

Suggested Stretching Exercises

Lower Body Stretch

Place feet shoulder-width apart and lean forward.

Keep this position for 30 seconds using the body as a natural weight to stretch the backs of the legs.

DO NOT BOUNCE!

When the pull on the back of the legs lessens, gradually try a lower position.

Bent Torso Pulls

While sitting on the floor, have legs apart, one leg straight and one knee bent.

Pull the chest down to touch the thigh on the leg that is bent, and twist at the waist.

Hold this position at least 10 seconds. Repeat 10 times on each side.

Floor Stretch

While sitting on the floor, open the legs as wide as possible. Stretch the upper body toward the knee on the right leg by using your arms to pull your chest to your thighs. Hold this stretch 10 to 30 seconds.

DO NOT BOUNCE!

Do this stretch 10 times.

Repeat the stretch with the left leg.

Bent Over Leg Stretch

Stand with feet shoulderwidth apart and lean forward as illustrated. Using the arms,

gently pull the upper body towards the right leg.

Let the head hang down.

DO NOT BOUNCE!

Hold the position a minimum of 10 seconds. Repeat pulling the upper body to the left leg. Do this stretch several times slowly.

Remember to always check with your physician before starting any exercise program.

Cool-Down

The purpose of cooling down is to return the body to its normal, or near normal, resting state at the end of each exercise session. A proper cool-down slowly lowers your heart rate and allows blood to return to the heart. Your cool-down should include the stretches listed above and should be completed after each strength training session.

18

LIMITED WARRANTY

MODEL 15-1100A

WARRANTY

Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship under normal use, service and proper operation for a period of 90 days on the parts and three years on the frame from the date of the original purchase from an authorized retailer.

THIS WARRANTY SHALL

NOT APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE,

MISUSE, ALTERATION OF ANY TYPE OR CAUSE OR TO ANY DEFECT OR DAMAGE CAUSED BY

REPAIR, REPLACEMENT, SUBSTITUTION OR USE WITH PARTS OTHER THAN PARTS PROVIDED

BY STAMINA PRODUCTS, INC. Commercial use includes use of the product in athletic clubs, health clubs, spas, gymnasiums, exercise facilities, and other public or semipublic facilities whether or not the product's use is in furtherance of a profit making enterprise, and all other use which is not for personal, family, or household purposes.

To implement this limited warranty, send a written notice stating your name, date, and place of purchase and a brief description of the defect along with your receipt to

Stamina Products, Inc. P.O. Box 1071,

Springfield Missouri, USA, 65801-1071, or email us at [email protected], or call us at

1-800-375-7520. If the defect is covered under this limited warranty, you will be requested to return the product or part to us for free repair or replacement at our option.

NO ACTION FOR BREACH

OF THIS LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER THE

DATE THE ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED. NO ACTION FOR

BREACH OF ANY IMPLIED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER

DELIVERY OF THE PRODUCT TO THE PURCHASER. This limited warranty is not transferable. IF

ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED WARRANTY OR ANY

IMPLIED WARRANTY, THE REMEDY OF REPAIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY

AVAILABLE TO YOU. In the event that the purchaser makes any claim under this limited warranty or any implied warranty, the Warrantor reserves the right to require the product to be returned for inspection, at the purchaser's expense, to the Warrantor's premises in Springfield, Missouri. Return of the enclosed warranty registration card is not required for warranty coverage, but is merely a way of establishing the date and place of purchase.

Stamina Products, Inc.

SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS

OF TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL,

SPECIAL OR INCIDENTAL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY

IMPLIED WARRANTY.

This limited warranty is the only written or express warranty given by Stamina Products, Inc. This warranty gives you specific legal rights, and you may also have other legal rights which vary from state to state.

ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OR

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED IN DURATION TO

THE DURATION OF THIS WARRANTY.

The laws in some jurisdictions restrict the rights of manufacturers and distributors of consumer goods to disclaim or limit implied warranties and consequential and incidental damages with respect thereto.

If any such law is found to be applicable, the foregoing disclaimers and limitations of and on implied warranties and consequential and incidental damages with respect thereto shall be disregarded and shall be deemed not to have been made to the extent necessary to comply with such legal restriction.

19

PRODUCT PARTS DRAWING

FRONT

BACK

20

PARTS LIST

PART#

32

34

35

36

28

29

30

31

24

25

26

27

20

21

22

23

13

14

16

17

9

10

11

12

5

6

7

8

1

2

3

4

45

46

47

48

49

51

53

54

41

42

43

44

37

38

39

40

55

56

57

58

PART NAME QTY

Main Frame

Rear Stabilizer

Front Stabilizer

Seat Post

Meter Post

Left Handlebar

Right Handlebar

Linkage

Pulley and Axle

Bearing (6003z)

Inner C Ring (35mm)

Spacer Washer (ø17 x ø22 x 0.5mm)

C Ring (17mm)

V-Ribbed Belt

Idler Wheel

Idler Wheel Spacer

Large Washer (ø16 x ø32 x 0.5mm)

Fan Wheel

Bearing (6000z)

Fan Axle

Wavy Washer (ø10 x ø13 x 0.4mm)

Spacer Washer (ø10 x ø13 x 0.5mm)

Spacer (ø10 x ø16 x 13.5mm)

Thin Nut (3/8" - 26 x 0.2" thick)

Thin Nut (3/8" - 26 x 0.28" thick)

Thin Nut (3/8" - 26 x 0.35" thick)

Eye Bolt (M6 x 1 x 50mm)

Tension Bracket

Left Fan Cage

Trim Strap

Left Cage Cover

Right Cage Cover

Meter

Connection Wire

Sensor Wire

Sensor Clip

Magnet

Left Cover

Right Cover

Small Crank

Tooth Lock Washer (M10) 4

Left Flange Nut, Brass Color (M10 x 1.25, Left Hand Threads) 1

Right Flange Nut, Black Color (M10x1.25, Right Hand Threads) 3

Crank Cap

Wavy Washer (ø17 x ø22 x 0.4mm)

Bearing (6003z)

Left Crank

Right Crank

Left Pedal

Right Pedal

Linkage Bushing

Plastic Washer (ø10 x ø18 x 2mm)

21

1

1

1

2

4

1

1

1

2

1

1

1

1

4

6

2

1

1

1

1

1

2

2

2

2

1

2

1

1

1

1

2

1

2

1

1

1

1

2

2

3

1

1

1

2

1

1

1

1

PARTS LIST

PART#

83

84

85

86

87

88

90

91

75

76

77

78

79

80

81

82

67

68

69

70

71

72

73

74

59

60

61

62

63

64

65

66

101

102

103

104

105

106

107

108

92

93

94

95

96

97

98

99

109

110

111

PART NAME

Handlebar Bushing

Washer (ø16.2 x ø22 x 1.5mm)

Washer (ø10 x ø25.4 x 2mm)

Left Rest Pedal

Right Rest Pedal

Pedal Cover

Shaft Bolt

Foam Grip

Round Plug (25.4mm)

Oval Plug (20mm x 40mm)

Handlebar Shaft

Seat

Sleeve

Adjustment Knob

Leveling Cap

Cap Bushing

Securing Cap

Wheel

Endcap (60mm)

Water Bottle Holder

Water Bottle

Carriage Bolt (M8 x 1.25 x 75mm)

Screw, Round Head (M4 x 12mm)





Screw, Round Head (M4 x 0.6 x 35mm)

Bolt, Button Head (M8 x 1.25 x 15mm)

Bolt, Button Head (M8 x 1.25 x 38mm)

Bolt, Flat Head (M10 x 1.5 x 35mm)

Nylock Nut (M10 x 1.5)

Nylock Nut (M8 x 1.25)

Nylock Nut (M6 x 1)

Acorn Nut (M8 x 1.25)

Nut (M4 x 0.6)

Washer (M8)

Arc Washer (M8)

Lock Washer (M8)

Warning Label

Allen Wrench w/ Screwdriver (6mm)

Large Wrench

Wrench

Manual

Socket Wrench

Right Fan Cage

Idler Arm

Tension Spring (ø14 x 60mm, wire ø2.3mm)

Bolt, Flat Head (M10 x 1.5 x 25mm)

C Ring (35mm)

Spacer Washer (ø17 x ø22 x 1mm)

22

QTY

4

2

1

1

4

2

3

1

1

4

2

8

2

2

2

1

1

1

2

2

2

4

2

1

1

2

2

2

4

2

2

1

1

1

1

1

1

1

1

1

8

6

8

1

8

2

4

1

1

4

2

For your convenience, Stamina’s customer service representatives can be reached by email at customerservice@ staminaproducts.com or by phone at 1-800-375-7520 (in the U.S.). Our customer service representatives are available Monday through Thursday from 7:30 a.m. until 5:00 p.m., and Friday 8:00 a.m. until 3 p.m. Central Time.

ONLINE

CUSTOMER SERVICE [email protected]


TELEPHONE


Tel: 1 (800) 375-7520

FAX


Fax: (417) 889-8064

MAIL

STAMINA PRODUCTS, INC.

ATTN: Customer Service

P.O. Box 1071 Springfield, MO. 65801-1071

Would you like to recieve email information or special offers from Stamina Products? Register at contact.staminaproducts.com

To enact your warranty, please register your product by going to register.staminaproducts.com. Please have your product model number (printed on the cover of this owner’s manual) and the serial number (printed on the black and white sticker on your product) ready.

If you don’t have internet access, you can call customer service at 1-800-375-7520, or fill out and mail the product registration form below to Stamina Products, Inc.; P.O. Box 1071; Springfield, MO 65801-1071.

PRODUCT REGISTRATION FORM Stamina Products, Inc.

P.O. Box 1071

Springfield, MO 65801-1071

Model Number: ...................................................................................... Serial Number: .............................................................................................

Product Name: ..................................................................................................................................................................................................................................

Place Purchased: ..............................................................................................................................................................................................................................

Date of Purchase: ..................................................................................

First Name: ............................................................................................

Purchase Price: ............................................................................................

Last Name: ...................................................................................................

City: .................................................................. State: ................................................................

Email Address: .......................................................................................

Zip Code: .................................................

Phone #: ( ) ......................................................................................

Would you like to receive email information or special offers from Stamina Products?* ____Yes ____No

*If yes, be sure your email address is included above.

Detach and Mail or Fax the Form Above

If there are missing or damaged parts, you can go to parts.staminaproducts.com and order those parts. If you have questions, please contact customer service. Do not return the product. To order parts by mail, fill out the sheet below and fax it to

417-889-8064. The part will be mailed to your address.

Detach and Mail or Fax the Form Below

PARTS ORDER FORM Stamina Products, Inc.

P.O. Box 1071

Springfield, MO 65801-1071

Mr./Ms: ..............................................................................................................................................................................................................................................

Address: ........................................ ............................................................................................. Apt. #:..........................................................................

City: .................................................................. State: ................................................................ Zip Code: .................................................

IMPORTANT : We must have your phone number to process the order!

Phone #: ( ) ................................................................................ Work Phone #: ( ) .............................................................................

Date of Purchase: ..................................................................................

Model #: ............................................................................................................................................................................................................................................

Purchased From: ..............................................................................................................................................................................................................................

IMPORTANT : Before filling out the form below make sure you have the correct information.

Refer to the parts list to make sure you're ordering the right parts!

PART #

EXAMPLE:

1

DESCRIPTION

Rear Unit Assembly

QUANTITY

1

No results