‹ RS485 4000’ MAX BELDEN 9842 OR EQUIVALENT
RS485 4000’ MAX BELDEN 9842 OR EQUIVALENT | 6000
< CONTROLLER COMMAND
2x8 [| 294 и CENTRE
12/24vDC | „VAC UL294
supply | МРОТ PIM400 | 2x18 |, /24vpc|_~ VAC SERVER
—485 POWER | > INPUT
L À SUPPLY | 2x18
| POWER| „ VAC
UP TO 200° MAX SUPPLY [> INPUT
ELECTRIC | = aS
HINGE a |
AD—300
LOCK AD—400 AD—400
LOCK LOCK
+|13,6 | vac
JV DCT’ INPUT
AD300 LOCK ; ac < HF | |
o an 294 | INPUT НЕМ
ra >, ELECTRIC 12/24wDC PIM400— SHIELD
| 489 BLUZUHT TR |
| ЕЕ — WHT/ORG -В IRS 485
| + |1
| — ГА
| e an + bh INSTALL -В IRSA85 CONTROLLER
INSTALL SHORTING AC um H BLDCKS +12 6000
¡BLOCKS ON RS485 INPU[_UNE| UL 294 VIE FP RS-485 —— GALLAGHER
MODULE 12/24VD0 ИНЫЕ
L _ oo 12/24 bi 0 RE [I an
< SHIELD = [
U LI PA
< ВИНТ п u NOTE! WHEN PIV/CAC CARDS ARE USED А GALLAGHER
р WHT/BLU A < SLDEN 9842 HS6000 PIV AND SOFTWARE MUST BE USED
< tee tt 120 OHM TERMINATION RESISTOR TO BE USED ON LAST
< SHIELD _\ DEVICE ON RS485 DATA LINE,
BELDEN 9842
OPERATION!
NOTES:
1 ALL LOW VOLTAGE WIRING TO BE STANDARD,
MULTI-CONDUCTOR COLOR CODED WITHOUT SPLICES.
2) WIRING TO CONFORM TO APPLICABLE NATIONAL, STATE
AND LOCAL ELECTRICAL CODES.
3) REFER TO SPECIFIC PRODUCT INSTALLATION
INSTRUCTIONS FOR SPECIFIC WIRING REQUIREMENTS.
4) THIS DRAWING IS FOR GRAPHICAL REPRESENTATION OF
PRODUCTS DETAILED IN THE HARDWARE SET ONLY.
9) X CONDUCTOR COUNT TO BE DETERMINED BY ACCESS
CONTROL PANEL PROVIDER.
GALLAGHER 6000 CONTROLLER SUPPORTS ЦР TO 16 AD—400 AND AD-300 TOTAL LOCKS ON 2 RS485 DATA
RS485 DATA LINE SUPPORTS UP TO 8 PIM400—485 OR 8 AD-300 WITH NO MORE THAN 8 AD300 AND PIMS
DATA LINE.
UL294 POWER SUPPLIES USED SHOULD NOT BOND EARTH GROUND TO SIGNAL GROUND.
IF PLENUM RATED CABLE IS REQUIRED USE BELDEN 82842 OR EQUIVALENT.
WIRING SHOWN REFLECTS WIRING FROM 6000 CONTROLLER TO PIM400-485 AND AD-300 ONLY. ADDITIONAL WIRING WILL BE |"
REQUIRED AND IS NOT SHOWN HERE.
CONTRO
LLER. F
INES. EACH
LOAT SHIELD ON LAST DEVICE ON RS485 DATA LINE.
SHIELD ON COMMUNICATION WIRES, BELDEN 3106A, SHOULD CONNECT TO EARTH GROUND AT ONE LOCATION ONLY, 6000
NOTE: CONFIGURATION HAS NOT BEEN TESTED BY ALLEGION BUT HAS BEEN REVIEWED AND APPROVED BY GALLAGHER
L
PER RS485
ri
ALLEGION YN.
"GALLAGHER 6000 CONTROLLER WITH
PIM400-485/AD-400 AND AD-300
DATE DRAWN! 04-08-22
REVISION O A _ 0 Q __ 2 2
APPROVED BY!
BLAKE SMITH
DWG NO:
115509
DRAWN BY:
B DOVE
REV
">
