Schlage AD-400 PIM400-485 Wiring Diagram

 RS485 4000' MAX
BELDEN 3106A
GALAXY 600/635 CONTROLLER
< Im
y O
<— 10' MAX DROP BELDEN 3106A K— 10' MAX DROP BELDEN 3106A :
120
2x18 [12/24VDC L > ТИ
1 on 120 PIM400-485 | Power | ~ VAC >
POWER |? vac X SUPPLY =
SUPPLY — Y
=” Ш
©
—
s
2x18 2
о
a= 8) []
\
ELECTRIC L 120VAC
AD300 HINGE AD400
LOCK LOCK
GALAXY 600/635
DSI MODULE
A SHIELD
| | BELDEN 3106A +
< WHT/ORG ——]
< ORG/WHT т
< BLU/WHT END
R-
R+
AD300 LOCK BELDEN 3106A |
———] — — PIM400-485 |
Г — ELECTRIC —]
| | HINGE ||
| | — J2 J5
| GND
| | — == TB+ =
| | | | J1 RB+ GND
| || H TA- =
| | L _ o RA- R+
| | + GND J8 J7 J10 J11 ~—
| REMOVE SHORTING - NEU | 120 A a HO —
| —
| BLOCKS ON RS485 | UL 294 LINE | VAC \ |
| MODULE | 12/24VDC \ + GND
LA SUPPLY \ | UL294 [Neu (420 —
a \ 12/24VDC [Une [ VAC
INSTALL J19 AND J20 SUPPLY —
SHORTING JUMPERS
NOTES:
1> ALL LOW VOLTAGE WIRING TO BE STANDARD,
MULTI-CONDUCTOR COLOR CODED WITHOUT SPLICES.
2> WIRING TO CONFORM TO APPLICABLE NATIONAL,
STATE AND LOCAL ELECTRICAL CODES.
3> REFER TO SPECIFIC PRODUCT INSTALLATION
INSTRUCTIONS FOR SPESCIFIC WIRING
REQUIREMENTS,
42 THIS DRAWING IS FOR GRAPHICAL
REPRESENTATION OF PRODUCTS DETAILED IN THE
HARDWARE SET ONLY.
5) x CONDUCTOR COUNT TO BE DETERMINED BY
ACCESS CONTROL PANEL PROVIDER,
EARTH GROUND SHIELD ON BELDEN 3106A CABLE AT GALAXY 600/635 CONTROLLER ENCLOSURE ONLY.
WIRING SHOWN REFLECTS WIRING TO SCHLAGE PIM-485 AND AD-300 FROM GALAXY 600/635 ONLY. ADDITIONAL WIRING WILL BE REQUIRED ON THE GALAXY 600/635 AND WILL NOT BE SHOWN HERE.
RS485 TERMINATION IS NOT TYPICALLY REQUIRED. IF YOU ARE EXPERIENCING INTERMITTENT OR ERRATIC COMMUNICATION PROBLEMS, INSTALL A 120 ohm RESISTOR AT THE BEGINNING AND AT THE
END OF THE RS485 DATA LINE PARALLELED ACROSS DATA LINES. NOTE, INCORRECTLY INSTALLED TERMINATION RESISTORS CAN CREATE MORE PROBLEMS AND SHOULD ONLY BE USED OF REQUIRED.
WITH HHD SET LO AND HI WAPM ID'S. BY DEFAULT, PIM USES 0-15, MUST BE CHANGED TO 1-16. IF LO IS 0 THEY WILL NOT COMMUNICATE.
UL 294 POWER SUPPLIES USED SHOULD NOT BOND EARTH GROUND TO SIGNAL GROUND.
IF PLENUM RATED CABLE IS REQUIRED USE BELDEN 82842 OR EQUIVALENT.
A PIM400-485 WILL SUPPORT UP TO SIXTEEN AD400 OR WRI400 OR WPR400 OR WSM400 TOTAL.
NOTE: CONFIGURATION HAS BEEN TESTED IN IALLEGION LABS AND HAS BEEN REVIEWED AND APPROVED BY GALAXY.
OPERATION! MAX SIXTY-FOUR AD400/AD300 PER GALAXY 600/635 CPU. EACH DSI BOARD HAS TWO RS485 PORTS EACH SUPPORTING UP TO SIXTEEN AD LOCKS EACH.
_ AB
ALLEGION &%
TITLE:
GALAXY 600/635 CONTROLLER
PIM400-485 WITH AD400/AD300 LOCK
105337
DATE DRAWN: 09-23-11
REVISION DATE:
[1-01-13
APPROVED BY
DAN GRAMLICH 07-23-13
DWG NO: REV
823112-6 GALAXY
DRAWN/CHECKED BY:
BRENDA DOVE 08/23/11
copyright 2013