(1) In this case, the application must not include any feature specific to V2 (see Functions available on all types of V2 operator panel). Otherwise, an error message is displayed when attempting to download the application to a V1 operator panel. To revert the application to

"V1 level", delete any V2 functions which have been used.

(2) In this case, the new V2 functions cannot be used.

___________________________________________________________________________

P/1

Main enhancements to PL7-MMI17 V2.2 software

The main enhancements to the PL7 -MMI17 V2.2 software compared to V2 are :

• Support for the new CCX17-A (V2.2) operator panel features :

- management of 78 FIPIO ROW-type objects,

• management of alarms assigned to diagnostic OFB fault bits,

• management of mailbox for alarms associated with FIPIO ROW-type objects,

• management of messages and message groups via FIPIO ROW-type objects,

• optimization of message handling for refresh operations,

• possibility of exchanges being made according to predefined periods,

• reconfiguration option if new OFB versions are installed,

• improvements to spreadsheet icons to enable easier identification,

• option to update alarm texts via the associated alarm bit comment,

• option to inhibit command keys in the system screens.

Compatibility between software version and terminal type is as follows :

V1 software

V2 software

Terminal V1 Terminal V2

LW, FW

YES

YES (1)

V2.2 software YES

YES

(2)

Terminal V2

TCCX17L, F,

LPS, FPS

YES

Terminal V2.2

YES

"V1 level", delete any V2 functions which have been used.

(2) In this case, the new V2 functions cannot be used.

___________________________________________________________________________

P/2

1 Presentation of the PL7-MMI 17 software

1.1

Introduction

PL7-MMI 17 is a station tool for developing man-machine interface applications which will be used to control automated systems from CCX 17 type industrial operator panels.

Several methods of communication enable the PLC application and the man-machine interface application to be synchronized.

PL7-MMI 17 stores the man-machine interface application in the operator panel

• Requests to display messages and execute commands are prompted by writing variables to a PLC data zone (this zone is called the mailbox). The CCX 17 operator panel periodically reads the data in the mailbox and executes the associated commands.

The advantage of this method lies in its simplicity (communication between the PLC and the operator panel is totally transparent and does not require any special programming).

• Requests to display messages and execute commands are prompted by sending text function blocks containing the numbers of the messages or of the groups of messages to be displayed.

This method enables the variables displayed on the operator panel to be refreshed slightly faster because there is no periodic scanning of the mailbox.

The messages and commands are sent on an ad hoc basis to the CCX 17 by the

PLC, using function blocks

All the messages reside in the PLC memory. This should be sized accordingly.

___________________________________________________________________________

1/1

1.2

Description of the required environment

The hardware required for running PL7-MMI 17 is either an FTX 507, FTX 417 type terminal or an IBM PS/2 microcomputer or PC compatible equipped with :

• OS/2 operating system (version 1.3 or later),

• XTEL or MINI-XTEL software workshop (version 5 or later),

• a mouse.

To integrate PL7-MMI 17 software under the software workshop requires the

Courier font set on the programming terminal. This font is supplied with the OS/2 operating system. The installation procedure for this font is described in section 3.3.

The TXT LF PL7 M17 V6 software package consists of :

• a set of 3"1/2 PL7-MMI 17 software diskettes,

• this manual,

• a licence agreement.

___________________________________________________________________________

1/2

Presentation of the PL7-MMI 17 software 1

1.3

Software functions

1.3-1 General

PL7-MMI 17 is a configuration tool with which the user can create all the data relating to a man-machine interface application on the CCX 17.

An application consists mainly of :

• a specific configuration for the CCX 17 operator panel being used,

• a list of status messages,

• a list of alarm messages,

• groups of status messages,

• assignment of the operator panel command keys and the PLC application program bit objects,

• a user-defined character font set.

PL7-MMI 17 enables several applications to be handled when several operator panels are connected to one PLC station.

___________________________________________________________________________

1/3

1.3-2 Methodology

The methodology described below is designed to guide the user when developing manmachine interface applications.

Creating an application or selecting an existing application (sect 5.1)

Configuring the operator panel and the link

(sect 5.2)

Creating status messages

(sect 5.3)

Creating alarm messages

(sect 5.4)

Creating groups of status messages

(sect 5.5)

Assigning the

CCX 17 operator panel command keys

(sect 5.6)

Creating or modifying character font sets

(sect 6.1-2)

Consistency test

(sect 6.1-3)

Transferring the application to the CCX 17 operator panel (sect 6.2)

Documenting the application

(sect 6.1-7)

Saving the application

(sect 6.1-4)

End

___________________________________________________________________________

1/4

Presentation of the PL7-MMI 17 software 1

1.3-3 Configuring the application

Configuring the application enables the communication protocol and its associated parameters as well as the various dedicated message zones of the mailbox communication to be defined.

Each of these functions is described in section 5.2

___________________________________________________________________________

1/5

1.3-4 Creating status messages

The status messages consist of text to which a PLC variable can possibly be associated.

This variable can be :

• displayed,

• refreshed,

• modified by the user.

This function is described in section 5.3

___________________________________________________________________________

1/6

Presentation of the PL7-MMI 17 software 1

1.3-5 Creating alarm messages

The alarm messages consist of text and possibly a variable, displayed on fault conditions detected by the PLC application.

The variables shown in the alarm messages hold the value which was read when the fault was detected.

The alarm messages are time-stamped and recorded in the operator panel.

This function is described in section 5.4

___________________________________________________________________________

1/7

1.3-6 * Creating groups of status messages

A group is a combination of status messages which is displayed on request by the application program. Several groups can be displayed on one physical screen.

The group concept simplifies the design of the PLC application handling the CCX 17 operator panel.

This function is described in section 5.5

___________________________________________________________________________

1/8

Presentation of the PL7-MMI 17 software 1

1.3-7 Assigning the CCX 17 command keys

This function enables the command keys on each side of the CCX 17 operator panel screen to be assigned to PLC bit variables.

This function is described in section 5.6

___________________________________________________________________________

1/9

1.3-8 Selecting and modifying a character font set

This function is used to select the character font set in which messages must be displayed on the CCX 17 operator panel.

The standard character font sets are modified using an editor in order to generate special symbols or characters.

This function is described in sections 6.1-1 and 6.1-2

___________________________________________________________________________

1/10

Presentation of the PL7-MMI 17 software 1

1.3-9 Saving and transferring the application to or from the CCX 17 operator panel

The man-machine interface application already created can be transferred to or from the

CCX 17 operator panel.

This transfer can be performed, either in local mode directly on the operator panel, or in remote mode, using the transparent communication of Series 7 PLCs.

These functions are described in section 6.2

___________________________________________________________________________

1/11

___________________________________________________________________________

1/12

2 Hardware installation

2.1

Connecting the terminal to the CCX 17 operator panel

2.1-1 Principles

The entire MMI application must be transferred to the target CCX 17 operator panel.

This transfer must be carried out in one of two ways :

• local transfer, by connecting the terminal directly to the CCX 17 operator panel

(physical connection),

• remote transfer, by connecting the terminal to the CCX 17 operator panel via a PLC

(logical connection), using the transparent network.

2.1-2 Direct connection to the CCX 17 operator panel

If the terminal being used is FTX 507, FTX 417 or CCX 57/77, it is connected to the

CCX 17 operator panel via cable reference T CCX CB8 030.

T CCX CB8 030

T CCX CB10 002

CCX 17

If the terminal being used is a PC or PC compatible, the terminal is connected to the

CCX 17 operator panel via cable reference T CCX CB89 030 which is connected to the

RS 232C / RS 485 adapter reference TSX SCA 72.

TSX SCA 72 junction box

T CCX CB89 030

RS232C

CCX 17

For more information on these connections, refer to the CCX 17 operator panel installation manual.

___________________________________________________________________________

2/1

2.1-3 Connection via a PLC

The programming terminal can access the CCX 17 operator panel via a PLC (either directly via the terminal port, or over an XWAY network).

Connection via PLC terminal port

FIPIO or UNI-TELWAY

CCX 17

Connection via a network

When the application PLCs are part of a network (or multinetwork) architecture, the programming terminal (on terminal port or network) can access a CCX 17 operator panel which is also part of the same architecture. Refer to the manual for the communication module being used for details of its operation and connections.

XWAY

Device X

Device Y

CCX 17

For more information on these connections, refer to the CCX 17 operator panel installation manual.

___________________________________________________________________________

2/2

3 Software installation

3.1

PL7-MMI 17 software installation

3.1-1 Preliminary operations

To use PL7-MMI 17, the Courier font set must be installed on the programming terminal.

Otherwise an error message is displayed on screen when the software is opened. This font set is loaded using the installation diskettes of the operating system being used

(OS/2 1.3, OS/2 2.1, etc). For more details, see section 3.3.

Before installing PL7-MMI 17 software on the hard disk, it is advisable to :

• read the licence certificate and warranty detailing restrictions on copying and installing the program,

• make a copy of the installation diskette to avoid any accidental damage and work only with the copy.

Important

The PL7-MMI 17 diskette is supplied write-protected. Do not alter the position of the write-protect tab.

3.1-2 Installation procedure

Before installing the PL7-MMI 17 software, ensure that the X-TEL V5 or Mini X-TEL V5

(or later) software workshop is already installed. If so, close all work sessions in progress then install the PL7-MMI 17 software, otherwise install the XTEL or MINI-XTEL software workshop (refer to the relevant manual).

PL7-MMI 17 software installation

• open an OS/2 full screen session,

• insert the PL7-MMI 17 diskette into the drive,

• type the identifier letter (a: or b:) of the drive where the diskette is located, and press

<Enter> to confirm,

• from the new prompt (for example [A:\] or [B:\] type install,

• follow the procedure shown on screen to install the PL7-MMI 17 software package,

• when installation has finished and if this is the last one, check the configuration as indicated on screen,

• remove the diskette from the drive and return to X-TEL by pressing <Ctrl> <Esc>.

___________________________________________________________________________

3/1

3.1-3 Bringing up the software

PL7-MMI 17 is a Station Tool. It is automatically installed when a station is created.

The mmi17 icon is therefore in the Station_Tools window.

___________________________________________________________________________

3/2

Software installation 3

3.2

Starting PL7-MMI 17

3.2-1 Initial screen

To access the PL7-MMI 17 software, click on the mmi17 icon in the Station_Tools window :

The initial screen for the program offers the following functions :

Management of the various application and configuration files.

See sections 5.1

and 5.2

A p p l i c a t i o n transfer (local or remote). See section 6.2

Various utilities.

See section 6.1

Access to the program help screens

Access to the editor functions.

See sections 5.3

to 5.6

Creation of the a p p l i c a t i o n documentation dossier. See section 6.1-7

Exit PL7-MMI 17

These functions can be accessed using either the mouse (see section 3.2-2) or the keyboard (see section 3.2-3).

___________________________________________________________________________

3/3

Icons give direct access to the various functions :

Opens an application (see section 5.1-2).

Saves the current application to hard disk (see section 5.1-3).

Creates status messages (see section 5.3).

Creates alarm messages (see section 5.4).

Creates groups of status messages (see section 5.5).

Assigns command keys (see section 5.6).

Modifies character font (see section 6.1-2).

Cut function.

Copy function.

Paste function.

Local transfer (see section 6.2-1 and 6.2-2).

Remote transfer (see section 6.2-3 and 6.2-4).

Generates the application documentation file (see section 6.1-7).

Prints the application documentation file (see section 6.1-7).

Launches the help associated with the current screen (see section 3.2-4).

___________________________________________________________________________

3/4

Software installation 3

3.2-2 Using the mouse

The various program functions can be accessed quickly using the mouse, without the need for detailed knowledge of the software.

It is used in the same way as in current word processing and graphics programs.

The standard functions (selecting a function, etc) are performed by clicking on the element in question. However, more sophisticated functions are available, such as multiple object selection, for a copy-and-paste operation for example.

These functions are shown below. They conform to the CUA standard (Common User

Access) :

Action

Click

Double Click

Shift-click

Click-drag

Result

Makes the selection.

Deselects any other selections.

Brings up a screen for modifying the selected field.

Deselects any other selections.

Selects all selections from the original cursor position to the current position.

Deselects any other selections.

Selects all selections between pressing and releasing the mouse.

Deselects any other selections.

Comment :

• A click corresponds to pressing the left-hand mouse button.

___________________________________________________________________________

3/5

3.2-3 Using the keyboard

Although the mouse is the most efficient means of using the software, all functions can be accessed via the keyboard.

The keyboard instructions are as follows :

• Shift F10 or ALT activates the program menu zone.

• To select a function on a pull-down menu, use the arrow keys and then confirm by pressing <Enter>. Alternatively, hold down the ALT key and then type the underlined letter for the desired action.

• Press F10 or ESC to exit the program menu.

• Use Tab (tabulation) to move to the next group.

• F6 or CTRL-F6 activates a secondary window.

• To work in keyboard mode in the data entry zone, the four arrow keys are used to move the cursor. Moving the cursor outside the window area (by using the arrows) causes the window to scroll in the direction of the arrow.

• PgUp and PgDn are used to move up and down the data entry zone.

• The Space bar is used to select or deselect a line in a list of multiple selections or to put a cross in a box.

Comments :

• The mouse can replace the keyboard as the user input peripheral at any time. It is represented by a mouse pointer which can go anywhere on the screen.

• When the user clicks on the left-hand mouse button in the data entry zone, and if there is a cursor, it will align with the mouse pointer at the click position.

___________________________________________________________________________

3/6

Software installation 3

3.2-4 On-line help

PL7-MMI 17 has its own on-line help which provides the user with information about the various program functions.

The on-line help is an essential complement to this manual.

To access the help screens, click with the mouse on the Help function at the top of the screen (or on the F1 function key) or on the Help button of the various dialog boxes shown.

Example of a help screen

___________________________________________________________________________

3/7

3.3

Installing the Courier character font

3.3-1 With OS/2 1.3

• Activate the OS/2 operating system,

• Restart terminal with the Installation A disk (1/11),

• When the following screens appear, press Enter (five times), until the system requests disk 1,

• Insert disk 1 (3/11) and press Enter,

• In the installation adjustment configuration screen, select 2 : Add selectable

system options and confirm with Enter,

• Then select the Font option, then confirm with Space bar and Enter,

• Place the cursor on Courier font and confirm with Space bar in both parts of the

screen. Then press Enter,

• When the system requests, insert disk 2 (4/11) followed by disk 4 (6/11),

• Reply No to Install the peripherals control,

• Remove the disk then restart the terminal.

3.3-2 With OS/2 2.1

• Click twice on the OS/2 icon,

• Click twice on the Configure system icon,

• Click twice on the Customized Installation icon,

• In the Configure system screen, do not modify anything and click on OK,

• In the following screen, OS/2 configuration and installation, select Font and click on Install,

• In the following screen, click on Install and insert the OS/2 disks which are requested,

• When the installation procedure has finished, remove the disk and restart the

terminal.

___________________________________________________________________________

3/8

4 Communication principles

4.1

General

To establish a dialog between the PLC and CCX 17 operator panels, a number of commands for the operator panels must be set up in the PLC application. Two types of

exchanges can be used for this purpose :

• exchanges via a mailbox : The messages to be displayed and the commands to be performed are transferred to the CCX 17 operator panel via a PLC memory zone allocated to exchanges between the PLC and the operator panel. This zone can be accessed in both read mode and write mode.

• exchanges via text function blocks : The messages to be displayed and the commands to be performed are transferred to the CCX 17 operator panel via text function blocks.

TxTi

The principles for using both these types of exchange are described later. Examples of applications using communication both via mailbox and text function blocks are provided in sections 7 and 8.

Both types of exchange can be used in the same application.

___________________________________________________________________________

4/1

Depending on the bus used for communication, (FIPIO or UNI-TELWAY), data exchanges are performed in different ways :

On the FIPIO fieldbus

Exchanges are performed :

• by a memory zone reserved for periodic exchanges specific to FIPIO, in which case the CCX 17 can access 8 words in read mode (ROW) and one word in write mode (RIW). This zone is automatically reserved in the PLC memory, and is extended to 78 ROW for the CCX17-A.

• by UNI-TE exchange requests

(communication via mailbox or by text function blocks).

The principles of communication on FIPIO

(ROW and RIW word management, etc) are described in section 4.5.

On the UNI-TELWAY bus

Exchanges are made by UNI-TE requests

(communication via mailbox or by text function blocks).

___________________________________________________________________________

4/2

Communication principles 4

4.2

Exchanges via mailbox

4.2-1 Mailbox structure

The mailbox which is reserved for exchanges with the CCX 17 operator panel is a zone in the PLC word or (on FIPIO) ROW memory. It contains a command table with the following structure :

Wi Status of indicator lamps

Wi+1 Number of message group to be displayed *

Wi+2 Number of 1st status message to be displayed

Wi+3 Number of 2nd status message to be displayed

...

Number of last status message to be displayed

* If the number of the group to be displayed is 0, the CCX 17 displays the messages whose number is contained in words

Wi+2 to Wn. If the number of the group to be displayed is not 0, only the selected group is displayed.

The start of this table, together with its length, are defined by the user when the application is created using PL7-MMI 17 (see section 5.2-2).

Note: To redisplay the same group, the corresponding mailbox word must be set to zero then reset to the group value.

4.2-2 Executing commands

The CCX 17 operator panel periodically scans this word table and executes the commands originating from the PLC application in the following order :

• Read then display the status of operator panel indicator lamps (read word Wi).

• Read the number of the message group to be displayed.

- if the number of the message group to be displayed is zero (Wi+1 = 0), the operator panel scans the contents of the following words in the table (Wi+2 to Wn), then displays all the status messages whose corresponding number is not zero. The word must be set to zero before changing the number of the new message to be displayed.

- if the number of the message group to be displayed is not zero, the operator panel only displays the status messages contained in the corresponding group.

Example :

Display of message number 10 (End of cycle) and message number 3 (Oven ready).

Mailbox zone

Wi = 0

Display messages number 10 and 3 Wi+1 = 0

Wi+2 = 10

End of cycle

Command table

Wi+3 = 3

Oven ready

Wi+4 = 0

...

Wn = 0

___________________________________________________________________________

4/3

4.2-3 Managing responses

When the displayed messages include a value to be entered, this is automatically written to the PLC data zone via UNI-TE requests.

Operator entry

Number of message or group

Speed = 352 rpm

Confirm

PLC data zone

Write entries via UNI-TE requests

___________________________________________________________________________

4/4

Communication principles 4

4.2-4 Managing acknowledgments : error processing

Monitoring the display of messages and possibly the entry of a variable is configured when the application is created using PL7-MMI 17 (see section 5.2-2).

The CCX 17 manages two types of acknowledgment :

• read acknowledgment,

• write acknowledgment.

Read acknowledgment

When this type of acknowledgment is required, the CCX 17 indicates in a PLC internal word table that the commands have been performed by the operator panel (lamps, messages displayed, etc). This word table is adjacent to and structured in the same way as the command table.

Example

In the example below, the application program only asks for status message number 10 to be displayed (End of cycle). If acknowledge on read is required, after message number

10 has been displayed, the CCX 17 operator panel automatically updates the corresponding word (Wn+4) in the table reserved for acknowledge on read.

Mailbox zone

Command table

Acknowledge on read table

Wi = 0

Wi+1 = 0

Wi+2 = 0

Wi+3 = 10

...

Wn+1

Wn+2

Wn+3

Wn+4 = 10

...

Display of message number 10

End of cycle

Update acknowledgment table

___________________________________________________________________________

4/5

Write acknowledgment

When this type of acknowledgment is required, the CCX 17 indicates in a PLC internal word table that the operator entry required has been entered. This word table, which is adjacent to the acknowledge on read table, is structured in the same way as the command table (if acknowledge on read is not required, this table is placed after the command table).

Example

In the example below, the application program requests the speed of the motor to be entered when status message number 22 is displayed (Speed = 60 rpm). If acknowledge on read and write is required, after message number 22 has been displayed, the CCX 17 operator panel automatically updates the corresponding word (Wn+3) in the table reserved for acknowledge on read. When the operator enters the required value, the corresponding word (Wm+3), is updated in the table reserved for acknowledge on write. The value entered by the operator is written into the PLC data zone via a UNI-TE request.

PLC data zone

Command table

Acknowledge on read table

Acknowledge on write table

Mailbox zone

Wi = 0

Wi+1 = 0

Wi+2 = 22

Wi+3 = 0

...

Wn+1

Wn+2

Wn+3 = 22

Wn+4

...

Wm+1

Wm+2

Wm+3 = 60

Wn+4

...

Display of message number 22

Update acknowledge on read table

Operator entry

Speed = 60 rpm

Confirm

Update acknowledge on write table

Write entry via UNI-TE request

___________________________________________________________________________

4/6

Communication principles 4

4.2-5 Managing alarm messages

A PLC bit or word memory zone, periodically scanned by the CCX 17 operator panel, is assigned to managing alarm messages. These messages are managed using word bits for TSX 17-20 and TSX 47-20 PLCs, whereas the other PLCs can use both a bit type zone and a word type zone. Each internal bit or each word bit of this table represents an alarm. The table structure is as follows :

Management by internal bits Management by word bit

F 0

Bi Alarm number 1

Bi+1 Alarm number 2

Bi+2 Alarm number 3

Bi+3 Alarm number 4

...

Bn-1 Alarm number n

Alarm number 1

Alarm number 2

Alarm number 3

...

Alarm number n in the word Wi+(n/16 - 1)

Both the start of this table and its length are defined by the user when the application is created using PL7-MMI 17 (see section 5.2-2).

Alarms are managed by the CCX 17 operator panel in one of two ways :

• The alarms are memorized in the operator panel while waiting to be displayed and acknowledged later by the operator. In this mode, status messages issued by the process can continue to be displayed.

Bi = 0

Bi+1 = 0

Bi+2 = 0

Bi+3 = 1

...

Bn =0

Display alarm number 4

Display messages and store alarms

Operator displays and later acknowledges each alarm

___________________________________________________________________________

4/7

• The alarm is memorized and then displayed on the operator panel. It remains displayed until acknowledged by the operator by pressing any key. Once the alarm has been acknowledged, the messages which were present on-screen prior to the alarm are once more displayed.

Bi = 0

Bi+1 = 0

Bi+2 = 0

Bi+3 = 1

...

Bn-1 =0

Alarm number 4

Overheating oven 4

Acknowledgment of each alarm by the operator

See CCX 17 installation manual, section on alarm logs.

___________________________________________________________________________

4/8

Communication principles 4

4.3

Exchanges via text function blocks

4.3-1 Displaying a message (or a group) without operator entry

The CCX 17 operator panel memory contains the application created using PL7-MMI 17.

This application comprises several types of messages :

• status messages comprising text (with or without operator entry),

• alarm messages,

• groups of messages, each group consisting of lists of status messages.

When the PLC application wishes to display a status message, a group or an alarm message on the CCX 17 operator panel, it indicates the number of the corresponding message (or group) in a text block transmission table. In all cases, the PLC receives confirmation of the exchange. If an error is detected, the first word in the text block reception table contains information to help identify the cause (see section 8.2-1).

TxTi

Number of the message or group

End of cycle

Transmission table

Reminder :

The CCX 17 operator panel can display several messages at the same time (up to 32 messages for a CCX 17-30 and 16 for a CCX 17-20).

These limits are valid for entry and refresh modes. The messages are positioned when they are defined either by selecting line and column or by defining whether the messages should be centered or aligned to the right or left. The user must therefore select the correct geographical position of the messages in order to prevent any overlapping.

The appendix to this manual contains grids which may be helpful for programming messages.

___________________________________________________________________________

4/9

4.3-2 Displaying a message with operator entry

When a displayed message includes a value to be entered by the operator, the entry can be fed back to the PLC in two different ways :

• operator entry neither checked nor synchronized by the PLC application,

• operator entry checked and synchronized by the PLC application.

(a parameter at the start of the text block transmission table defines which method is selected) :

Both examples are discussed later.

Operator entry neither checked nor synchronized by the PLC application

The request is sent via text block and confirmed immediately (text block command = 24).

Operator entry

TxTi Number of the message

Speed = 352 rpm

Transmission table

Confirm

PLC data zone

Write entries via UNI-TE requests

The value(s) entered are written directly to the PLC data zone via UNI-TE requests.

In all cases, the PLC receives an exchange report. If an error is detected, the first word in the text block reception table contains information to help define the cause (see section 8.2-1).

___________________________________________________________________________

4/10

Communication principles 4

Operator entry checked and synchronized by the PLC application

This option can only be used for sending status messages. The text block report is only updated when the entry has been carried out. The entry is in the text block reception table

(text block command = 22).

Operator entry

TxTi

Number of the message

Speed = 352 rpm

Reception table

Value of the entry

Confirm

The value entered by the operator is sent to the text block reception table.

In all cases, the PLC receives an exchange report. If an error is detected, the first word in the text block reception table contains information to help define the cause (see section 8.2-1).

___________________________________________________________________________

4/11

4.3-3 Request to display an alarm message

The CCX 17 operator panel contains the alarm messages in its memory (generated using PL7-MMI 17). An alarm message from the PLC application program is displayed by transmitting a text block containing the number of the alarm message.

Alarms are managed by the CCX 17 operator panel in one of two ways :

• the alarms are memorized in the operator panel while waiting to be displayed and acknowledged later by the operator. In this mode, status messages issued by the process can continue to be displayed.

TxTi Number of the alarm

Display messages and store alarms

Transmission table

Operator displays and later acknowledges each alarm

• the alarm is archived and then displayed on the operator panel. It remains displayed until it is acknowledged by the operator by pressing any key. Once the alarm has been acknowledged, the messages which were present on-screen prior to the alarm are once more displayed.

TxTi Number of the alarm

Oven 4 overheated

Transmission table

Acknowledgment of each alarm by the operator

In all cases, the PLC receives an exchange report. If an error is detected, the first word of the text block reception table contains information to help define the cause (see section 8.2-1).

___________________________________________________________________________

4/12

Communication principles 4

4.3-4 Managing the operator panel indicator lamps

On the front panel of the CCX 17 operator panel there are three indicator lamps. These lamps show the results of the self-tests during operator panel power-up, then once the self-tests are complete, they are made available to the user. The status of the indicator lamps (on, off or blinking) is modified by transmission of a text block containing the required values.

TxTi

Status of the indicator lamps

Transmission table

Indicator lamp display

4.3-5 Assigning the operator panel command keys

CCX 17 operator panels have several command keys assigned by configuration to PLC internal bits. They are assigned by transmitting a text block containing the required values.

TxTi Assigning the keys

Transmission table

Using the command keys

___________________________________________________________________________

4/13

4.4

Alarm management via the mailbox and text block

In order to simplify the management of alarms in the same application, an alarm can only be activated one way, via the text block or via the mailbox.

Alarms accessible via the mailbox depend on the length of the mailbox. Alarms with a number greater than the length of the mailbox can only be accessed via the text blocks.

Alarm table

Alarm 1

Alarm 2

Alarm 3

Alarm 4

Alarm 5

Alarm 6

•••

Alarm i

Alarm i+1

•••

Alarm n

Length of alarm zone in the mailbox = i

Alarms accessible via the mailbox

Alarms accessible via the text blocks

Example

In CCX 17-30•••, the maximum number of alarms is 300.

If the field reserved for alarms in the mailbox has a length of 150 bits (value configured in the Data link configuration screen) :

• alarms numbered from 1 to 150 are only accessible via the mailbox,

• the others are only accessible via the text blocks.

___________________________________________________________________________

4/14

Communication principles 4

4.5

Communication principle on the UNI-TELWAY bus

Reminder :

A CCX 17 operator panel connected to a UNI-TELWAY bus can communicate simultaneously :

• via mailbox, as shown in section 4.2,

• via text function block, as shown in section 4.3.

Number of possible connections :

It is recommended that no more than two CCX 17 are connected to the same

UNI-TELWAY bus.

Performance

Refresh time as a function of the number of CCX 17 operator panels connected :

1 CCX 17

2 CCX 17

3 CCX 17

4 CCX 17

5 CCX 17

6 CCX 17

Refresh for

4 requests + mailbox

1 second

1.8 seconds

2 seconds

3.4 seconds

4.5 seconds

6 seconds

Refresh for

1 request + mailbox

0.5 second

0.6 second

0.7 second

0.8 second

1 second

The configuration used for these measurements is as follows :

• TSX 107-455 PLC,

• UNI-TELWAY SCM 2116 Master,

• Default refresh and exchange zone periods (fast and 400ms),

• Default UNI-TELWAY time-out,

• Speed 9600 bds,

• MAST task period = 100ms

___________________________________________________________________________

4/15

4.6

Communication principles on the FIPIO fieldbus

Reminder :

A CCX 17 operator panel connected to a FIPIO fieldbus can communicate simultaneously :

• via mailbox, as shown in section 4.2,

• via text function block, as shown in section 4.3,

• by using the FIPIO periodic message handling system. This communication mode is demonstrated below.

Principles

In order for a CCX 17 to be able to exchange information via FIPIO, it must be configured using the XTEL-CONF station tool (for more details about using this tool, refer to the corresponding document).

___________________________________________________________________________

4/16

Communication principles 4

XTEL reserves a memory zone specific to data exchanges shared between the PLC bus arbitrator and each CCX 17 configured on a FIPIO fieldbus. These exchanges occur periodically without intervention by the PLC application program.

This memory zone is composed of :

For the CCX 17 family :

• eight words (ROW) written by the PLC and read by the CCX 17,

• one word (RIW) written by the CCX 17 and read by the PLC.

For the CCX17-A family :

• 78 words (ROW, ROWA, ROWB, ROWC, ROWD) written by the PLC and read by the

CCX 17,

• one word (RIW) written by the CCX 17 and read by the PLC.

Note :

The only configuration possible for the CCX 17-A family is as a CCX 17 in its basic

V2.2 version.

ROW ROWA... ROWD

RIW

___________________________________________________________________________

4/17

Syntax

A CCX 17 can display status or alarm messages containing ROWs or send information to the PLC via a RIW word.

For the CCX 17 family, the syntax of these words is as follows :

• ROWi,j,k where i corresponds to the CCX 17 connection point (from 1 to 62), j = 0 and k corresponds to the position of the ROW to be read (from 0 to 7).

Example : ROW3,0,5 to read the sixth ROW word assigned to the CCX 17 connected at connection point 3.

• RIWi,j,k,l is used by the CCX to send the control button status to the PLC automatically, i corresponds to the CCX 17 connection point (from 1 to 62), j = 0, k =0 and l corresponds to the bit position of the RIW

(for more information, refer to section 5.6-1).

For the CCX 17-A family, the 78 words can be addressed in the following way :

• ROWi,j,k where i corresponds to the CCX 17 connection point (from 1 to 62), j = 0 and k corresponds to the position of the ROW to be read (from 0 to 15),

• ROWAi,j,k with k from 16 to 31 inclusive,

• ROWBi,j,k with k from 16 to 31 inclusive,

• ROWCi,j,k with k from 16 to 31 inclusive,

• ROWDi,j,k with k from 16 to 31 inclusive.

Attention

The ROW and ROWA variables are not consecutive. On the other hand, ROWA,

ROWB, ROWC, ROWD are consecutive.

Examples : ROWA5,0,16 to read the seventeenth ROW word assigned to the

CCX 17-A connected to connection point 5.

ROWB5,0,17 to read the thirty-fourth ROW word assigned to the CCX 17-A connected to connection point 5.

(for more information, refer to section 5.6-1).

Important :

It is strongly recommended that these elements are used instead of standard words or bits in order to improve display and PLC dialog performance : the timesaving is from a factor of 5 to 10 depending on the dialog applications.

___________________________________________________________________________

4/18

Communication principles 4

Managing RIW/ROW in PLC tasks

It is possible to manage RIW/ROW in one task and ROWA...ROWD in another. These elements will always be updated at the rate of the task in which they have been configured.

Selection is made when the CCX 17 is configured using the XTEL-CONF tool and is only possible for the CCX 17-A family.

Task modification is accessed via the Parameters button in the screens below :

___________________________________________________________________________

4/19

Maximum number of devices

The maximum number of devices which can be connected depends on the type of

CCX 17 operator panels and how they communicate on the FIPIO fieldbus :

• If no CCX 17 is sending messages, the maximum number of CCX17 which can be connected is 7 for the CCX 17-A type and 25 for the CCX 17 type.

• If the configuration has only one PLC with several CCX 17 sending messages (wordtype variable, exchanged bit), the maximum number of CCX 17 is given by the formula :

Max no. =

2 x CPU scan time

This number is divided by 2 for the TSX 47-455.

The PLC scan time is expressed in seconds in this formula.

Example:

For TSX 67-455 to TSX 107-455 type PLCs with a scan time of 50 ms, the maximum number of CCX 17 is 10.

The maximum number of CCX 17 is 5 for a TSX 47-455 PLC with the same scan time

(50 ms).

4.7

Optimization rules

Certain rules must be observed to ensure optimization :

• The objects must be of the same type,

• The difference between the object indices must be less than certain values depending on the object type :

For internal bits (Bi), the maximum difference between index values is 480.

For word bits (Wi,x), the maximum difference between index values is 59.

For internal bits (Wi), the maximum difference between index values is 59.

For double words (DWi), the maximum difference between index values is 29.

Optimization examples :

It is possible to send a single request (by object type) to access the following objects :

• B0, B100 and B480.

• W0,0 to W59,F.

• W0, W1, W2 and W59.

• DW0, DW10 and DW29.

___________________________________________________________________________

4/20

5 Using PL7-MMI 17 software

5.1

File management

5.1-1 Creating a new application

After opening PL7-MMI 17 software, click on this icon or select the

Application/Select function. The screen which appears is used to define :

• the application name (8 characters maximum),

• the type of operator panel associated with this application. The product references are :

CCX 17 20F

CCX 17 20FW

CCX 17 20FPS

CCX 17 20L

CCX 17 20LW

CCX 17 20LPS

CCX 17 30L

CCX 17 30LW

CCX 17 30LPS

• a comment associated with the application (120 characters maximum).

5.1-2 Opening an existing application

After opening PL7-MMI 17 software, click on this icon or select the

Application/Select function. Choose the application to be opened from the list of names offered :

Once the selection has been confirmed, the terminal runs a procedure to check application consistency. This function checks the consistency between the variable/symbol pairs of the application and the station database.

For more details concerning this function, see section 6.1-3

___________________________________________________________________________

5/1

5.1-3 Saving an application

Save function

This function, accessible by clicking on this icon or by selecting

Application/Save or by pressing the F7 function key updates the file on hard disk, which contains the MMI application.

This file corresponds to the contents of status messages, alarm messages, status message groups, assignment of command keys, character fonts and the configuration.

When this function is launched, a message is displayed indicating that a save is taking place.

Save As function

This function, accessed by selecting Application/Save As enables the current application to be duplicated inside the same station. After naming the application, the OK button launches the function. When saving has finished, it is this new application which is visible on the screen.

5.1-4 Deleting an application

To delete an application, start the Application/Delete function then select the application to be deleted from the list displayed.

The selected application is deleted after confirmation.

___________________________________________________________________________

5/2

Using PL7-MMI 17 software 5

5.1-5 Changing type of operator panel

The type of operator panel can be changed provided the new operator panel has more extensive functions (eg changing from a CCX 17-20 to a CCX 17-30).

The operator panel can also be changed for one with less extensive functions if the following points are respected :

• The maximum number of status messages, alarms, message groups and configuration of the command keys must be accepted by the new operator panel.

• The line numbers of the status messages must be accepted by the new operator panel.

• The number of messages and the numbers assigned to the message groups must be accepted by the new operator panel.

• The length of the command and alarm zone must be accepted by the new operator panel.

• The number of the group displayed by default must be accepted by the new operator panel.

If these conditions are not satisfied, a message indicates the type of error. Changing from one operator panel to another is therefore impossible. The user must consequently modify the application in order to change the operator panel.

It is not possible to change a type of operator panel with a FIPIO application (CCX 17-

20F / 20FPS 20L / 20LPS / 30L and 30LPS) to an operator panel which does not accept

FIPIO (CCX 17-20LW 20FW / 30 LW).

___________________________________________________________________________

5/3

5.2

Configuring the application

5.2-1 Configuring the operator panel

This function enables the parameters of the CCX 17 operator panel which will receive the application to be configured. It is divided into two parts :

• configuration of general parameters (operator panel setup language, date format, etc),

• configuration of "protected" parameters (type of protocol used, etc). This data can only be accessed once a password has been entered.

Configuring the general parameters

The configuration screens are accessed from the initial program screen by selecting the

Application/Configure/CCX 17 Operator Panel function.

This screen shows the type of operator panel being used and offers the following modifications :

Language

Date format

Cancel

This item enables the language used in the setup of the CCX 17 operator panel to be chosen. Five languages are available : English

(by default), French, German, Italian and Spanish.

This item enables the format in which the date is displayed to be chosen,

• US : (by default) displays the date in American format (MM/DD/YY)

• Europe : displays the date in European format (DD/MM/YY)

• Japan : displays the date in Japanese format (YY/MM/DD)

Confirms the entries and returns to the initial program screen.

Cancels the entries and returns to the initial program screen.

___________________________________________________________________________

5/4

Using PL7-MMI 17 software 5

Configuring "protected" parameters

"Protected" parameters can only be accessed by entering a password.

Password

This screen is used to enter the password, which must contain four numerical characters. The default value is 0000 (or enter).

The numbers do not appear on-screen when the password is entered (asterisks confirm the pressing of keys). If the password is not valid, the screen opposite is displayed. Entering the correct password provides access to the screen below :

This screen summarizes the selections already made and offers the following modifications :

Default group No

This item enables entry of the number of the group whose messages will be displayed by default when the operator panel is powered up or the application is started. If the user does not want the message to be displayed when the operator panel is switched on, this field should contain the value zero (or should be empty).

___________________________________________________________________________

5/5

Refresh period

Exchange zone period

This item is used to enter the read frequency of the command mailbox.

There are 9 possible choices :

None / 400ms / 800ms / 2s / 4s / 8s / 32s / 1min / 5min.

The "none" value means that the CCX 17 never consults the command mailbox.

Inhibit keys

This item is used to enter the update rate of the variables displayed on the CCX 17. Ten values are possible :

Fast / 400ms / 600ms / 800ms / 1s / 2s / 4s / 10s / 30s / 1min.

The "fast" value means that the CCX 17 reads the variable value as fast as possible.

The CCX 17 sends one request per time unit : therefore a value of

1 second means that the CCX 17 will wait 1 second before reading the next variable.

For example, if the CCX 17 is displaying a Wi word and the time and if 1sec is configured, the time will be updated every two seconds.

Cancel

Used to inhibit the command keys when :

- consulting the setup

- consulting the list of archived alarms

- viewing the list of active alarms

- an alarm is superimposed

- viewing the list of entries

Confirms the entries and returns to the initial program screen.

Cancels the entries and returns to the initial program screen.

___________________________________________________________________________

5/6

Protocol

Using PL7-MMI 17 software 5

This function, accessed from the initial screen, authorizes modification of the operator panel - PLC data link parameters.

Operator panel protocol

This enables the operator panel protocol to be selected :

• Unitelway slave : the operator panel is configured as a slave of the

UNI-TELWAY bus (which is the most frequent case),

• Unitelway master : the operator panel is configured as the

UNI-TELWAY bus master (this has to be used when the operator panel is connected to the terminal port of a TSX 17-20 micro-PLC).

• Fipio : the operator panel is configured to be connected to a FIPIO fieldbus.

When changing the protocol, the software checks that non validated addresses for the new protocol do not already exist in the status or alarm messages (a ROW is for example not allowed in a UNI-TELWAY protocol). If this is not the case changing the protocol is not allowed.

Unitelway protocol

This item enables the parameters of the UNI-TELWAY link to be selected :

• Speed : communication speed must be between 300 and 19200 bauds (the default speed is 9600 bauds). All devices connected on the same bus must have the same communication speed.

• Time-out : the time-out corresponds to the response time of the PLC application to a request sent by the CCX 17 operator panel. This must be at least equal to 10000 ms. If this is not the case, an error message is displayed.

• Slave address : this field, which can only be accessed when the protocol for the operator panel is specified as "Unitelway master", enables the slave address which will communicate with the operator panel to be selected.

___________________________________________________________________________

5/7

FIPIO protocol This item enables the connection point of the CCX 17 operator panel on the FIPIO fieldbus to be selected.

Printer link

When changing the value of the connection point, all the ROWi,j,k type variables included in status or alarm messages are automatically assigned to the new connection point if they are symbolized in the station database. If this is not the case, changing of the connection point is denied.

The CCX 17 must be configured on the new connection point in XTEL-

CONF.

This item enables the printer parameters to be selected.

• Communication speed : choice of bit rate, values can be between

300 and 9600 bauds,

• Parity : corresponds to the type of link parity (even, odd or none),

• Data : corresponds to the number of data bits (7 or 8 bits),

• Stop bit : corresponds to the number of stop bits (1 or 2),

• Log print-out : Confirms or inhibits the continuous printout of operator panel messages.

___________________________________________________________________________

5/8

Using PL7-MMI 17 software 5

Password entry Modification of the "protected" parameters of the application is controlled by password. This item enables it to be changed.

Reminder :

• The password, containing numerical characters only, must include four digits. It must be entered twice for security reasons.

• The numbers do not appear on-screen when the password is entered (asterisks confirm the pressing of keys).

___________________________________________________________________________

5/9

5.2-2 Configuring the Data Link

This function enables the tables required for mailbox communication to be configured.

It is accessed from the initial program screen by selecting the Application/Configure/

Data Link function.

This screen is divided into two parts :

• one part reserved for the report,

• one part reserved for mailbox exchanges. This part is divided into two zones :

- dedicated alarm zone,

- dedicated command zone.

PART RESERVED FOR THE REPORT

Report variable and Report symbol

The CCX 17 operator panel generates a status word (at the end of its self-tests) which is written into an internal word of the PLC memory.

This internal word must be symbolized in the station database. The user specifies either the variable (eg W100) or symbol (eg St_12) when entering this word. Details on this status word are given in section 10.1-

If the symbol for this word has not been defined in the station database, the following message is displayed on the screen.

___________________________________________________________________________

5/10

Using PL7-MMI 17 software 5

Once the message has been confirmed, the terminal asks if the user wants to run the station database in order to assign a symbol to this internal word.

Alarm acknowlegment

The selection of this function enables the CCX 17 to return the number of the alarm message acknowledged by the user to the PLC. This value is written to the word following the status word reserved for the report variable (for example, if W100 is the report variable, the word dedicated to the alarm acknowledgment is W101).

PART RESERVED FOR THE ALARM ZONE

This zone is divided into three zones which must not overlap :

• Zone 1: The first alarm zone is used to define a table used for alarm communication via shared memory between the PLC and the panel. The length specified corresponds to the number of words or bits (depending on the variable).

Start variable or Start symbol

These fields are used to enter the variable or symbol for the first object in the table which is specific to the type of station used :

• For a TSX 17 or TSX 27 station, the variable must be a word; each word bit represents an alarm which should be displayed.

• For other types of station, the variable can be a bit, word or ROW.

Comments

When a bit (or a word bit) in this table changes to 1, the alarm message corresponding to this bit is displayed on the operator panel. As with the other parameters where a variable has to be entered, the first internal word (or bit) in this table must be symbolized in the station database.

When data is entered, the user must specify either the variable (eg

B10, W200, etc) or the symbol (eg Alarm_4) of this bit or word. If the symbol is not defined in the station database, a message enables, as for the status parameter, the station database to be run.

If no variable or symbol is selected or if the length defined is zero, the

CCX 17 operator panel does not use this type of exchange for the alarms.

For TSX 17 or TSX 27-47 type stations, the variable must be a word.

___________________________________________________________________________

5/11

Start

This field is used to define the number of the first alarm message for zone 1.

Length

This field specifies the length of the table.

For a TSX 17, TSX 27 or TSX 47 type station, the maximum length of the table is 10 words for a CCX 17-20 or 15 for a CCX 17-30.

For other types of station, the maximum length of the table depends on the type of variable used :

• bit : the length of the table is limited to the maximum number of alarm messages (150 for a CCX 17-20 or 300 for a CCX 17-30)

• word : the length of the table is limited to the maximum number of modulo 16 alarm messages (10 for a CCX 17-20 or 19 for a

CCX 17-30)

• ROW type : the length of the table is limited to the maximum number of modulo 16 alarm messages and to the type of family used

(CCX 17 or CCX 17-A)

Overflow is not possible between ROWs in different functional units

(for example, in the following diagram there can be no overflow between ROW and ROWA) :

CCX 17 PLC

MAST, FAST or AUX task

UF0 UF1

RIW

ROW

ROWA

ROWB

ROWC

ROWD

▲ ▲ ▲ ▲

12345678901234567890123456789012123456789012345678901234567890121234567890123456

FIPIO

12345678901234567890123456789012123456789012345678901234567890121234567890123456

• Zones 2 and 3 : These zones are used to manage events linked to diagnostic OFBs, via their error bits.The start of these zones (which are not necessarily contiguous) is specified. The specified length corresponds to the number of OFB bits in the zone.

OFB status management

This check box is used to manage on a CCX 17 the new alarm display screens, associated with zones 2 and 3 : OFB alarm zone

variables screen and OFB alarm zone status screen (messages associated with status word bits at state 1).

___________________________________________________________________________

5/12

Using PL7-MMI 17 software 5

Start variable or Start symbol

These fields are used to enter the variable or symbol of the first monitored error bit, for a given type of diagnostic OFB (for example,

EPON0,ERROR). During operation, when the monitored error bit of a

OFB changes to 1, the corresponding alarm message is displayed on the CCX 17 operator panel.

Start

Length

The value entered in this field is used to define the number of the start alarm message, for zone 2 or zone 3.

The value entered in this field specifies the length of the table allocated to the alarm zone; in other words, the number of the OFB to be monitored. This length can be anything up to 60.

The 3 alarm zones (zones 1 to 3) share the same space without any overlap between the different zones.

OFB alarm zone variables screen

This screen can be accessed via the Screen/OFB alarm zone

variables command and is used to display all the diagnostic OFB error bit type variables associated with alarm events. The function is only active when the OFB status management mode is validated in the Data Link Configuration screen.

Alarm

Variable

Symbol

Comment

<F2> indicates the number of the alarm associated with the address.

displays the variable (diagnostic OFB error bit) of the alarm event.

displays the symbol for the alarm event.

displays the comments for the alarm event.

this key is used to display the data relating to alarm zones 2 and 3 alternately.

___________________________________________________________________________

5/13

OFB alarm zone status screen

This screen can be accessed via the Screen / OFB alarm zone status command and is used to display the comments associated with the various diagnostic OFB status word bits being monitored.

The function is only active when the OFB status management mode is validated in the Data Link Configuration screen.

Bit

Text (line 1)

Text (line 2)

<F2> indicates the number of the status word bit (0 to 15 or 0 to 31).

displays the first 37 characters of the comment associated with the status word bit.

displays the subsequent characters (37 maximum) of the comment associated with the status word bit.

this key is used to display the data relating to alarm zones 2 and 3 alternately.

___________________________________________________________________________

5/14

Using PL7-MMI 17 software 5

DESCRIPTION OF THE COMMAND ZONE

The command zone is used to define a word table which is used for communication via shared memory between the PLC and the operator panel.

Start variable or Start symbol

These fields are used to enter the variable or symbol of the first object in the

PLC table where the operator panel will read the commands. This must be an internal word (W) or ROW and must be symbolized in the station database. When entering data, the user must specify either the variable (eg

W150) or symbol (eg Table_2) of this word. If the symbol is not defined in the station database, a message enables, as for the report parameter, the station database to be run.

Length This parameter specifies the length of the table reserved for the command zone. For a TSX 17 or TSX 27 type station, it is limited to 12 words, for whichever type of operator panel is used :

. one word for commanding the operator panel indicator lamps,

. one word for the number of the status message group to be displayed,

. up to 10 words for status messages (one word per message).

For the remaining types of station, status message words are limited to

4 per line on the operator panel. The length of the zone is therefore limited to18 words for a CCX 17-20 (one indicator lamp command word, one word for the group number and 4 lines x 4 words for messages) and to

34 for a CCX 17-30 (one indicator lamp command word, one word for the group number and 8 lines x 4 words for messages).

___________________________________________________________________________

5/15

Length

CCX17

For ROW-type addresses, zones may overflow between ROWA, B, C or

D formats (for example, if ROWAi,0,31 is five words long, it is correct.

CCX 17 will read words ROWAi,0,31 and ROWBi,0,16 to ROWBi,0,19).

1234567890

12345678901

RIWi,0,0

RIWi,0,7

ROWi,0,0

ROWi,0,15

ROWAi,0,16

12345678901

ROWAi,0,31

12345678901

ROWBi,0,31

ROWCi,0,16

ROWCi,0,31

ROWDi,0,16

ROWDi,0,29

MAST,

FAST, or AUX task

MAST,

FAST, or AUX task

PLC

If the number of messages entered is greater than this limit, the message below is displayed :

Read acknowledgment

Write acknowledgment

When dialogue is via shared memory, these check boxes enable the use of :

. the response to a display zone (read acknowledgment), and/or

. the response to an entry zone (write acknowledgment).

Depending on which type of acknowledgement has been confirmed, the

PLC must have a memory space which is twice (one type of acknowledgement confirmed) or three times (both types of acknowledgement confirmed) the length of the command zone.

___________________________________________________________________________

5/16

Using PL7-MMI 17 software 5

For a ROW-type command zone, management of acknowledgements

(read/write) uses 6 RIW-type words :

. RIWi,0,1 : acknowledge alarms,

. RIWi,0,2 : acknowledge indicator lamps in read mode,

. RIWi,0,3 : acknowledge the group number in read mode

. RIWi,0,4 : acknowledge messages in read or/and write mode,

. RIWi,0,5 : acknowledge messages in read or/and write mode,

. RIWi,0,6 : acknowledge messages in read or/and write mode,

. RIWi,0,7 : acknowledge messages in read or/and write mode.

Example

• The operator panel used is a CCX 17-30L.

• It must write its report word to the PLC internal word W250 (symbol Table_8).

• The alarm zone starts at internal word B200 (symbol Alarm_2) and has a length of

10 bits.

• The user wishes to display up to 20 status messages, thus the command zone has a length of 20 + 2 = 22 internal words and starts at word W100 (symbol St_12). The acknowledgments on read and write are requested. The total length of the word table used in the PLC is thus 66 words (3 * 22).

___________________________________________________________________________

5/17

5.2-3 Configuring the device

This function enables definition of the devices (the PLC and two others) which can communicate with a CCX 17 operator panel connected on a FIPIO fieldbus.

This function is accessed from the initial program screen by selecting the Application/

Configure/Device function.

This screen enables entry of :

• the name (maximum of 10 characters) assigned to the PLC device,

• the names of two other devices which can communicate with the CCX 17,

• the connection point of each of these two devices on the FIPIO bus.

• the length of requests supported by the device with two predefined values (128 and

32),

• the possibility of optimizing requests (the device supports 36H and 37H requests to read / write word string, bits or word bits).

When creating status messages, alarm messages or when assigning the command keys, the user must indicate the name of the device with which he wishes to communicate in the Device cells of the relevant entry screens. In this case, only the PLC address can be used to identify a variable.

Devices connected on FIPIO must include a UNI-TE server to process V5 requests, to be accessed directly by the CCX17.

___________________________________________________________________________

5/18

Using PL7-MMI 17 software 5

Rules for optimizing requests

If the CCX 17 has to display several messages each containing a variable, these variables are read as a single request. The same type of processing requires several requests to be sent if optimization is not requested.

Certain rules must be observed to ensure optimization :

• The objects must be of the same type,

• The difference between the object indices must be less than certain values depending on the object type :

For internal bits (Bi), the maximum difference between index values is 480.

For word bits (Wi,x), the maximum difference between index values is 59.

For internal bits (Wi), the maximum difference between index values is 59.

For double words (DWi), the maximum difference between index values is 29.

Optimization examples :

It is possible to send a single request (per object type) to access the following objects :

• B0, B100 and B480.

• W0,0 to W59,F.

• W0, W1, W2 and W59.

• DW0, DW10 and DW29.

___________________________________________________________________________

5/19

5.3

Creating status messages

5.3-1 Principles of data entry

After starting PL7-MMI 17 software, click on this icon or select the Screen/

Status Messages function. A window is displayed containing a spreadsheet in which all the status message parameters of the application can be described :

As not all of the parameters to be entered can fit on the screen, a horizontal scroll bar enables those columns which are hidden to be accessed. This presentation has the advantage of displaying data relating to several messages on the same screen, but does require that the spreadsheet be moved to be able to see the entire message.

Entering data

Data is entered field by field.

• The active cell is surrounded by a rectangle.

• The entry cursor is a blinking rectangle.

• The arrow keys, the TAB key or the Enter key as well as the mouse can be used to move from one field to another. The cut, copy and paste functions can also be used.

• A space or double-click on a field places the cursor at the end of the entry field.

• Clicking on a field and then entering characters deletes the line and confirms the entry.

• Pressing the Esc key when entering fields cancels the modifications.

If an error is detected in a field, a message indicating the cause(s) of the error is displayed at the top of the screen.

Position of the message text

The position of a message on a line is defined by selecting its display column. It is therefore possible to use the Screen/Message Position function to center or align the message to the left or to the right. This function is accessible after having selected the

5/20

Using PL7-MMI 17 software 5

Comment :

Fields are usually entered one after the other according to their position in the spreadsheet. Moving from one field to another automatically confirms the previous selection. Depending on the type of status message requested, one or more errors may be flagged to the user if not all the data relating to the status message is entered. Moving from one message to the next is only possible if no error has been detected.

Fast entry

A dialog box, which can be activated by double-clicking on the number of the status message or by pressing the Ctrl TAB keys (the cursor then looks like a magnifying glass) enables all the status message parameters to be entered and displayed. This dialog box is used in the rest of this manual.

Entering data in each of the fields is simplified by pulldown menus detailing the various choices available for the parameter selected.

Data is entered field by field. The TAB key or the mouse can be used to move from one field to another.

Unlike the presentation on the previous page, moving from one field to another does not confirm the last entry.

All parameters entered are taken into account when the screen is confirmed. This is the point at which any error messages are displayed.

This screen can only be confirmed when all errors have been corrected.

___________________________________________________________________________

5/21

5.3-2 Description of the data entry screen

Reminder

Two types of screen are available for the user to enter messages (see section 5.3-1).

These screens have the same functions but are presented differently, one in the form of a spreadsheet, the other in the form of a dialog box. Only entry in the dialog box will be described in this document as it can display all the parameters relating to a particular message.

Cancel

Confirms the screen contents.

Cancels the modifications.

Help

<< >>

Displays the program help screens.

Confirms the screen contents and moves to the previous or following status message.

Message text Field for entering the message text which is displayed on the CCX 17 operator panel. It can contain a maximum of 40 characters.

Line Specifies the line on which the message is displayed (default value = 1).

Column Specifies the column on which the message is displayed

(default value = 1).

Attribute Defines the message display attribute. The following are available :

• N : normal

• B : blinking

• R : reverse video

• A : reverse video and blinking.

Size Specifies the format of all the text and variable characters to be displayed :

• Standard : standard height and standard width

• Double : double height and double width.

___________________________________________________________________________

5/22

Using PL7-MMI 17 software 5

Print

Command

Type of field

Device

Confirms the continuous printout of the status messages.

This field enables a unique command, which is executed before display of the message, to be assigned to the message. The choices are :

• NON : No command assigned to the message.

• CLS : Clears the screen.

• CLL : Clears the line on which the message is to be displayed.

• CMH : Clears the status message log.

• CAH : Clears the alarm message log.

• RKB : Used with mailbox communication, this parameter indicates to the CCX 17 operator panel that a value must be entered by the user.

• PMH : Sends the status message log to print.

• PAM : Sends the alarm message log to print in chronological order.

Defines the type of parameter field (entered or displayed) associated with the message. The possible choices are :

• NON : No field is associated with the message displayed.

• BIT : The message is associated with a bit type field.

• ANA : The message is associated with a 16-bit integer field.

• LNG : The message is associated with a 32-bit integer field.

This type is valid for ROW. Two consecutive elements are read in the

CCX 17.

• STR : The message is associated with a word string or to a floating point number (see for example section 5.3-7).

• LST : The message is associated with a word type index.

• DAY : The message is associated with the current date.

• HOU : The message is associated with the current time (the date and time are periodically synchronized to the PLC).

Specifies the name of the device to which the variable to be read is assigned. The devices which can communicate with the CCX 17 are defined by the Application/Configure/Device function. This function is only available when the CCX 17 is connected on a FIPIO fieldbus (if it is connected on a UNI-TELWAY bus, it can only communicate with the master).

___________________________________________________________________________

5/23

Variable

Symbol

Specifies the address of the variable already associated with the message. When communicating with the PLC, if the symbol associated with the variable exists in the station database, it is taken into account automatically when the screen is confirmed. If not, the terminal suggests running the database in order to update it. The variables are as follows :

• bit objects (internal bits Bi, word extract bits Wi,j in read only), ROW bits,

• word objects (internal words Wi or internal double words DWi),

• OFB elements (OFB constants, OFB data, input or output parameters, etc.)

• ROW objects specific to FIPIO communication.

Specifies the symbol for the variable associated with the message. If the symbol entered is not defined in the station database, the terminal suggests running the database in order to update it. If the symbol already exists, the variable associated with the symbol is taken into account automatically when the screen is confirmed.

When communicating with a device other than a PLC and when a database is not available, this field cannot be used.

Comment

Type

Displays the comment for the variable associated with the message

(for information purposes only). It is defined in the station database.

Specifies the message display format :

• N : None.

• A : ASCII format.

• D : Decimal format.

• B : Bargraph format (the user must define the display limits of the bargraph).

Sign Specifies whether the variable to be displayed is signed.

A signed internal word has a value between -32,767 and +32,767, otherwise it is between 0 and 65,535.

An signed double internal word has a value between

-2,147,483,647 and +2,147,483,647, if not it is between

0 and 4,294,967,295.

Length / Decimal places

If the display format is Decimal, decimal places specifies the number of digits to display after the decimal point. If the display format is

ASCII, decimal places is replaced by Length and specifies the number of consecutive words to be read.

Display limits Provides access to a dialog box which enables the range of authorized values for the variable to be determined.

___________________________________________________________________________

5/24

Using PL7-MMI 17 software 5

Refresh

Type

Entry limits

Specifies whether the variable contained in the message must be updated periodically when it is displayed.

Specifies the type of data entry associated with the variable :

• N : None.

• I : Incremental entry (the user must define the increment value and the entry limits). On the CCX 17 operator panel, a parameter value is modified by pressing the left and right arrow keys.

• L : Normal entry using numeric keys.

• V : Entry of predefined values.

Provides access to a dialog box used to select :

• the entry limits and the increment value for an incremental entry,

• the entry limits for a Free style entry.

Predefined values

Gives access to a dialog box in order to predefine a list of possible values (this choice is only possible for entering Predefined Values).

These values are arranged in ascending order. 16 values maximum.

___________________________________________________________________________

5/25

5.3-3 Request to display a message

If the user simply wishes to display a message containing alphanumeric characters, only those fields relating to the display need to be filled in (text, attribute, size and position) and, if required, a command assigned to the message.

Example :

Data :

• "End of cycle" message displayed in reverse video, double width and double height on line 4 and starting at column 13.

• The message must be accompanied by the clear line command.

Parameter selection :

• As the message must be accompanied by the clear line command, the Command field is therefore CLL.

• This message does not need any particular data from the PLC, nor any intervention by the operator, thus the field type is NON : None.

The screen corresponding to this example is as follows :

___________________________________________________________________________

5/26

Using PL7-MMI 17 software 5

5.3-4 Request to display a message comprising a variable

To display a message comprising a value issued by the process, the user fills in the fields relating to :

• the display (text, attribute, size and position) and, if required, a command assigned to the message,

• the characteristics of the variable to be displayed (displaying a floating point variable is described in section 5.3-7).

Example :

Data :

• "Oven 4 Temperature = xxx.xx

C" message displayed, where xxx.xx represents the temperature value (the value must comprise five digits with two after the decimal point).

• The temperature value is shown in the PLC word W110 (or ROW).

• The display is in normal mode and standard size on line three starting at column one.

• No command is assigned to the message.

Parameter selection :

• Since this message requires data from the PLC, data relating to the field type must be made available.

• The message text must include an indication of the field size of the value displayed.

The conventional method is to represent each expected character by an underscore

"_". Thus, in this example, the message text must include six underscores (five for the number itself plus one for the decimal point).

• The field type is ANA (16-bit word) and the variable is updated periodically.

• The display format is Decimal with two digits after the decimal point (decimal places = 2). If, for example, the contents of W110 is 12345, the display on the operator panel is 123.45.

The screen corresponding to this example is as follows :

___________________________________________________________________________

5/27

5.3-5 Request to display a message with entry of a process value

To display a message comprising a value issued by the process and which needs to be modified by the operator, the designer fills in the fields relating to :

• the display (text, attribute, size and position) and, if required, a command assigned to the message,

• the characteristics of the variable to be displayed,

• the entry format.

Example :

Data :

• "motor rotation speed = xxxx tr/mm" message displayed, where xxxx represents the rotation speed of the motor (the expected value must therefore contain four decimal digits).

• The rotation speed of the motor is specified in PLC word W55.

• The display is in blinking mode and standard size on line 2 starting at column 6.

• The entry made by the operator must be incremental (in steps of 100 rpm between

1000 and 3000 rpm).

Parameter selection :

• Since this message requires data from the PLC and an entry by the operator, data relating to the field type and the entry format must be made available.

• The message text must include an indication of the field size of the value displayed.

The conventional method is to represent each expected character by an underscore

"_". Thus, in this example, the message text must include four underscores.

• The field type is ANA (16-bit internal word).

• The refresh option must be selected.

• The display format must be Decimal with no digits after the decimal point.

• The entry type must be incremental.

• The entry limits must be 1000 for the minimum limit and 3000 for the maximum limit.

• The increment value must be 100 rpm.

Note :

When mailbox communication is used and the message comprises an operator entry, the Command field must be RKB.

___________________________________________________________________________

5/28

Using PL7-MMI 17 software 5

The screens relating to this example are as follows :

___________________________________________________________________________

5/29

5.3-6 Request to display a character string

To display a character string issued by the process, the user fills in the fields relating to :

• the display (text, attribute, size and position) and, if required, a command assigned to the message,

• the characteristics corresponding to this string.

Example :

Data :

• "Parameters = xxxxxxxxxxxxxxxxxxxx" message displayed, where xxx... represents a character string (the string is 10 words long and starts at PLC word W60 (or ROW)).

• The display is in normal mode and standard size on line one starting at column one

(no command is assigned to the message).

Parameter selection :

• Since the display of a character string requires data from the PLC, data relating to the field type must be made available.

• The text must include an indication of the field size of the value displayed. The conventional method is to represent each expected character by an underscore "_".

Thus, in this example, the message text must include 20 underscores (two characters per internal word).

• The field type must be STR (String).

• The display format must be ASCII.

• The length of the character string must be 10 words.

• The refresh option must be selected.

The screen corresponding to this example is as follows :

___________________________________________________________________________

5/30

Using PL7-MMI 17 software 5

5.3-7 Request to display a floating point value

To display a floating point value issued from the process, the user fills in the fields relating to the display (text, attribute, size and position) and, if required, a command assigned to the message.

Important :

• The floating point values must be seen by PL7-MMI 17 as an integer value displayed in decimal. The floating point value from the application must therefore first be scaled to remove the decimal point then converted to an integer (eg, for a value with 2 digits after the decimal point, DW0 * 100 → DW2; FTB(DW2) → DW4).

Example :

Data :

• "Measure = xxx.xx"

C message displayed, where xxx... represents the floating point measurement scaled and converted to an integer.

• The display has two digits after the decimal point in normal mode and standard size on line one starting at column one.

Parameter selection :

• Since the display of a floating point value requires data from the PLC, data relating to the field type must be made available.

• The text must include an indication of the field size of the value displayed. The conventional method is to represent each expected character by an underscore "_".

Thus, in this example, the message text must include 6 underscores (five significative digits plus the decimal point).

• The field type must be LNG : 32-bit and decimal type display format.

• The number of digits after the decimal point must be 2.

• The refresh option must be selected.

The screen corresponding to this example is as follows :

___________________________________________________________________________

5/31

5.3-8 Request messages using a word as an index

It is possible to use a word as an index in a pre-stored message. The operator panel displays the message whose number is contained in the designated word (only the text of this message is displayed). To do this, the user must fill in the fields relating to :

• the display (text, attribute, size and position) and, if required, a command assigned to the message,

• the characteristics relating to this string.

Example :

Data :

• "Color = xxxxx" message displayed, where xxx... is a message pre-stored in the operator panel. The number of the message to be displayed is contained in word

W124. If W124 = 18, the text of message number 18, containing, for example, the text

Red, is displayed after "Color =".

• The display is in reverse video and standard size on line 4 starting at column 10 (no command is assigned to the message).

Parameter selection :

• Displaying an indexed message requires data from the PLC, thus data relating to the field type must be made available.

• The text must include an indication of the field size of the value displayed. The conventional method is to represent each expected character by an underscore "_".

Thus, in this example, the message text must include five underscores.

• The field type must be LST (Message).

• The display format must be ASCII.

• The field length does not need to be filled in.

• The refresh option must be selected.

___________________________________________________________________________

5/32

Using PL7-MMI 17 software 5

5.4

Creating alarm messages

5.4-1 Principles of data entry

After starting PL7-MMI17, click on this icon or select the Screen/Alarm

Messages function. A window is displayed containing a table in which all the application alarm message parameters can be described.

The principles for entering data in the table are identical to those for status messages

(for more details, see section 5.3).

As with status messages, data can be entered using two different screens :

• A screen in the form of a spreadsheet.

• A screen in the form of a dialog box displaying all parameters relating to a particular alarm (this is the screen format which is used for the rest of this section).

___________________________________________________________________________

5/33

5.4-2 Description of the entry screen

Cancel

Help

<< >>

Alarm event

Confirms the screen contents.

Cancels the modifications.

Displays the program help screens.

Confirms the screen contents and moves to the previous or next alarm message.

Specifies the alarm event assigned to this message in the alarm zone configuration.

Message text Field for entering the alarm message text which is displayed on the

CCX 17 operator panel. It can contain a maximum of 40 characters.

Size Specifies the format of all the text and variable characters to be displayed :

• Standard: standard height and standard width

• Double : double height and double width.

Display Specifies whether the alarm message must be displayed in superimposed mode on the screen (in all cases, the message is stored in the CCX 17 operator panel and can be displayed later).

Print Confirms the continuous printout of the alarm message.

Type of field Defines the type of parameter field assigned to the message :

• NON : No field is assigned to the message displayed.

• BIT : The alarm message is assigned to a bit type field.

• ANA : The alarm message is assigned to a 16-bit integer field.

• LNG : The alarm message is assigned to a 32-bit integer field.

This type is valid for ROW. Two consecutive elements are read in the

CCX 17.

• STR : The alarm message is assigned to a word string.

___________________________________________________________________________

5/34

Using PL7-MMI 17 software 5

Device

Variable

Symbol

Comment

Type

Signs

(if it is connected on a UNI-TELWAY bus, it can only communicate with the master).

Specifies the address of the variable assigned to the alarm message.

When communicating with the PLC, if the symbol assigned to the variable already exists in the station database, it is taken into account automatically when the screen is confirmed. If not, the terminal suggests running the database in order to update it. The variables are as follows :

• bit objects (internal bits Bi, bits extracted from words Wi,j in read only, ROW bits

• word objects (internal words Wi or double internal words DWi).

• ROW objects specific to FIPIO communication.

Specifies the symbol for the variable assigned to the alarm message.

If the symbol entered is not defined in the station database, the terminal suggests running the database. If the symbol already exists, the symbol assigned to the variable is taken into account automatically when the screen is confirmed.

When communicating with a device other than a PLC and when a database is not available, this field cannot be used.

Displays the comment for the variable assigned to the alarm message

(for information purposes only). It defined in the station database.

Specifies the display format of the alarm message. The following choices are available :

• N : None.

• A : ASCII format.

• D : Decimal format.

Specifies whether the variable to be displayed is signed.

A signed internal word has a value between -32,767 and +32,767, otherwise it is between 0 and 65,535.

A signed double internal word has a value between

-2,147,483,647 and +2,147,483,647, if not it is between

0 and 4,294,967,295.

___________________________________________________________________________

5/35

Decimal places / Length

If the display format is Decimal, Decimal Places specifies the number of digits to be displayed after the decimal point. If the display format is ASCII, Decimal Places is replaced by Length and specifies the number of consecutive words to be read.

Comments :

Unlike status messages, not all parameters are used for alarm messages, such as :

• Line : alarm messages are automatically displayed on the second line of the screen.

• Column : alarm messages are automatically displayed on the left side of the screen.

• Attribute : alarm messages are always displayed in normal mode.

• Date and Time : alarm messages are automatically time-stamped.

• Refresh : the variables displayed are never updated in an alarm message.

• Field attribute : this function is invalid because an alarm message can neither be entered nor displayed as a bargraph.

Two examples of alarm messages are given later :

• An alarm message containing text only

• An alarm message displaying a value issued by the process.

Of course, it is possible to have alarm messages which display a character string (STR type field). The display principle is identical to that described for status messages.

___________________________________________________________________________

5/36

Using PL7-MMI 17 software 5

5.4-3 Request to display an alarm message

If the user wishes to display an alarm message containing alphanumeric characters, only the fields relating to the display need to be filled in (text, size and type of display).

Example :

Data :

• "Emergency stop" message displayed in double width and double height.

• The message must be displayed on the operator panel screen.

Parameter selection :

• This message does not require any particular data from the PLC, thus the type of field is NON : None.

The screen corresponding to this example is as follows :

___________________________________________________________________________

5/37

5.4-4 Request to display a message comprising a variable

To display an alarm message followed by a value issued by the process, the user fills in the fields relating to :

• the display (text, size and type of display)

• the characteristics relating to the variable.

Example :

Data :

• "Overheating Oven 4 = xxx.xx

C" message displayed, where xxx.xx represents the temperature value (the expected value must therefore comprise five digits with two after the decimal point).

• The CCX 17 is connected to the FIPIO fieldbus at connection point 16, the temperature value is written by the PLC in the third word of the ROW table reserved for this connection point (the address of this word is ROW16,0,2).

• The display is in standard size and the message must be printed in continuous printout.

Parameter selection :

• Since this message requires data from the PLC, data relating to the type of field must be made available.

• The message text must include an indication of the field size of the value displayed.

The conventional method is to represent each expected character by an underscore

"_". Thus, in this example, the message text must include six underscores (five for the number itself plus one for the decimal point).

• The type of field must be ANA (16-bit internal word).

• The display format must be Decimal with two digits after the decimal point

(decimal places = 2). If, for example, the contents of ROW16,0,2 is 12345, the display is 123,45

The screen corresponding to this example is as follows :

___________________________________________________________________________

5/38

Using PL7-MMI 17 software 5

5.5

Creating status message groups

5.5-1 Principles of data entry and description of the screen

After starting PL7-MMI 17, click on this icon or select the Screen/Message

Groups function. A window is displayed which is used to assign various previously created messages to a group number.

Group number Selects the group number.

And Clear screen

Clears the CCX 17 operator panel screen before the corresponding group is displayed.

Message number

Enables the messages which make up the group to be selected. Data relating to the messages selected (number and content) is displayed in the corresponding box.

A message is inserted in the list above the current line (in reverse video).

The maximum number of groups and the number of messages per group depend on the type of CCX 17 operator panel :

• CCX 17 20 : 50 groups of eight messages maximum

• CCX 17 30 : 100 groups of 16 messages maximum.

An error message is displayed if the maximum number of messages per group is exceeded.

___________________________________________________________________________

5/39

5.5-2 Example of a status message group

Important :

A group can contain several different messages. Thus, the user must take note of the display position (line and column numbers) of each of the messages of the group on-screen to avoid any message being overwritten.

___________________________________________________________________________

5/40

Using PL7-MMI 17 software 5

5.6

Assigning the operator panel command keys

5.6-1 Principles of data entry and description of the screen

After starting PL7-MMI 17, click on this icon or select the Screen/

Command Keys function.

A window is displayed containing a table which is used to configure the manual command keys for the operator panels (these keys can either be assigned to PLC internal bits, or to RIW word bits or to CCX 17 discrete outputs if they have them). The principles of data entry are identical to those for status messages (for more details, see section 5.3).

Data can be entered using two different screens, one screen in the form of a spreadsheet and the other in the form of a dialog box displaying all the parameters relating to a particular command key (this screen format is used for the rest of this section).

Cancel

Help

<< >>

Function

Confirms the screen contents.

Cancels the modifications.

Displays the program help screens.

Confirms the screen contents and moves to the previous or next key.

Enables the command key operating mode to be entered :

• EDG : edge mode (pressing the key sets the assigned bit to 1, releasing the key sets it to 0).

• TOG : toggle mode (pressing the key causes the bit to change state).

___________________________________________________________________________

5/41

Device

Variable

Symbol

Comment

Displays the name of the device to which the variable to be updated is assigned. This name is declared when the device is configured

(see section 5.2-3).

Specifies the address of the internal bit Bi assigned to the key. If the symbol assigned to the bit already exists in the station database, it is taken into account automatically when the screen is confirmed. If not, the terminal suggests running the database in order to update it.

Specifies the symbol assigned to the bit. If the symbol entered is not defined in the station database, the terminal suggests running the database in order to update it. If the symbol already exists, the symbol assigned to the variable is taken into account automatically when the screen is confirmed.

Displays the comment for the variable assigned to the bit (for information purposes only). It is defined in the station database.

Warning :

When a CCX 17 is connected to a FIPIO fieldbus, the command keys not assigned to addresses or symbols are automatically assigned :

• to a bit in the first RIW word corresponding to the connection point when a CCX 17 is connected to a FIPIO fieldbus,

• to the corresponding discrete outputs in the case of CCX 17-20FPS or LPS or

CCX 17-30LPS.

An example of a CCX 17-30LPS on connection point 16 and which does not have a bit assigned to the command keys (variable and symbol fields empty) :

Key n

1 is assigned to bit RIW16,0,0,0 as well as to discrete output number 1,

Key n

2 is assigned to bit RIW16,0,0,1 as well as to discrete output number 2,

Key n

3 is assigned to bit RIW16,0,0,2 as well as to discrete output number 3,

Key n

4 is assigned to bit RIW16,0,0,3 as well as to discrete output number 4,

Key n

5 is assigned to bit RIW16,0,0,4 as well as to discrete output number 5,

Key n

6 is assigned to bit RIW16,0,0,5 as well as to discrete output number 6,

Key n

7 is assigned to bit RIW16,0,0,6 as well as to discrete output number 7,

Key n

8 is assigned to bit RIW16,0,0,7 as well as to discrete output number 8.

For any given command key, this principle of automatically assigning to an RIW bit and / or a discrete output is exclusive, with standard assigning of command keys to internal bits in the PLC.

___________________________________________________________________________

5/42

Using PL7-MMI 17 software 5

5.6-2 Example of configuring the command keys

Suppose the first six command keys on a CCX 17-30 are assigned to connection point

5, to the internal bits below and the following two to RIW :

Reminder of key assignment Key 1

Key 2

Key 3

Key 4

Key 5

Key 6

Key 7

Key 8

: bit B101 edge function

: bit B56 edge function

: bit B84 toggle function

: bit B18 edge function

: bit B72 toggle function

: bit B86 toggle function toggle function edge function.

Each bit used in this example must be symbolized in the station database. The two command keys assigned to RIW

(respectively RIW5,0,0,6 for key 7 and

RIW5,0,0,7 for key 8, where 5 represents the FIPIO connection point) must have their address and symbol fields empty.

Data is entered as shown on the screen opposite :

Once all the command keys are configured, the table summarizing the data entered is as follows :

The bits used as well as the corresponding RIW are updated by the operator when the command keys are pressed. The PLC program then executes the associated actions.

___________________________________________________________________________

5/43

5.7

Automatic updating of alarm texts

This function replaces the alarm message text with the comment associated with the alarm event (the comment is searched for in the application then in SDBASE).

The other message fields are set to their default values.

When the alarm events of a message have no associated comment, or the message has no associated alarm event, the message will not be modified.

This operation can be accessed via the Screen menu.

This function can only be activated if the alarm message spreadsheet is open and active.

To update several messages, simply select them before activating the function.

If no selection is made, the action will apply to all messages.

___________________________________________________________________________

5/44

6 Additional functions

6.1

Utilities

6.1-1 Selecting the character font

This function, started by selecting Screen/Font/Select enables the user font assigned to the application to be selected.

The screen is divided into two parts :

Type of font Enables the font which will be assigned to the application to be selected either from the system fonts or from the user-defined fonts.

List of fonts Displays the fonts which are available depending on the type of font selected.

When a user-defined font is selected, its origin is indicated by the item "From" :

Copy

Cancel

Help

If the type of font selected is Application font, this function enables the font of an existing application to be selected and copied to the current application.

Confirms the screen contents.

Cancels the modifications.

Displays the program help screens.

___________________________________________________________________________

6/1

6.1-2 Modifying the character font

This function, started by clicking on this icon or by selecting Screen/Font/

Editor enables the selected font to be displayed and modified in both display sizes, standard or double.

The modifications made using this editor are only shown when the relevant characters are displayed on the CCX 17 operator panel.

The editor is used as follows :

First select the character to be modified, either by entering the character directly via the keyboard, or by scrolling through the list of characters. Once this selection has been made, the character selected then appears in the grid.

An ASCII character is represented by four different combinations :

• The ASCII character has not been modified.

• The ASCII character has been modified by the user in standard size format and retains its default status in double size format.

• The ASCII character has been modified in double size format and retains its default status in standard size format.

• The ASCII character has been modified in standard and double size format.

To meet these requirements, several buttons enable the characters to be modified in each of these modes.

Standard

Double

Displays the character selected in standard size display mode.

Displays the character selected in double size display mode (double width and double height).

Conversion This key enables the modifications made to a standard character to be transferred to a double size character. It is not possible to reduce a character modified in double size format to a standard size format.

Return This function is only offered when the Conversion key has been pressed. It allows the user to cancel the modifications made and return the character to its initial standard format.

___________________________________________________________________________

6/2

Additional functions 6

Modifying a character using the keyboard

The TAB key moves the cursor between the various functions.

The arrow keys move the cursor within the grid.

The color of a rectangle is changed using the space bar.

Modifying a character using the mouse

Clicking with the left hand mouse button on a single rectangle changes its state.

By holding down the left hand button and dragging the mouse, the state of several rectangles can be changed at the same time.

Comments :

• Selecting the Screen/Clear function or pressing the Del the on the keyboard returns to the default system character format.

• Selecting the Application/Save function or pressing the F7 function key saves the modifications.

• The grid format is directly linked to the number of columns specified in the configuration part of the application. The default grid is 6*16 (40 columns).

• A modified character only appears on the operator panel screen when a message which includes it is displayed (the modification is not displayed on the entry screens).

Example :

Modifying the figure nine, in double size format only.

___________________________________________________________________________

6/3

6.1-3 Application coherence check

This function is run automatically when an existing application is opened (or imported). It ensures that the address-symbol assignments of the MMI application match those of the PLC database. It can also be run at the request of the user by selecting Utilities/Variable Coher-

ence.

Any inconsistencies detected between the station database and data entered in the various PL7-MMI 17 screens (different symbols, etc) are displayed and can be corrected automatically.

The screen is split into two boxes :

The Incoherences box displays any inconsistencies detected.

• Type specifies the type of message where there is inconsistency, denoted by :

- E for status messages

- A for alarm messages

- T for command keys

- C for the symbols and variables used for the Data link configuration.

• Num gives the message reference where there is inconsistency, denoted by :

- STA for the variables-symbol assignment of the status word,

- ALA for the variables-symbol assignments of the alarm field,

- COM for the variables-symbol assignment of the command field,

- the number in the case of status messages, alarm messages, or command keys.

• Symbol and variable indicate that the symbol and the variable are not consistent with the station database.

___________________________________________________________________________

6/4

Additional functions 6

The Corrections box indicates those corrections made by the PL7-MMI 17 program

(the automatic correction procedure is started by pressing the Variable key). There are two types of correction :

• Accepting the symbol shown in the PLC database when it differs from the symbol entered in PL7-MMI 17 (this may, for example, be caused by a modification to the PLC database).

• Creating a symbol assigned to the variable when its symbol does not exist in the PLC database. The symbol created corresponds to the variable preceded by # (or to

MMIxxx for the OFB elements or the ROW).

The data given in this box (Type, Num, etc) has the same meaning as in the Coherence box.

Important :

The corrections made by this function are local to the MMI application and do not modify the station database.

Variable Starts the correction function (with priority for the variable). A message indicates the end of the operation. The Corrections box then displays the modifications made.

Coherence Runs the consistency check again.

Sdbase

Runs the station database so that the user can make the modifications.

Confirms the modifications. All the variables concerned are corrected in the MMI application.

Example of screen :

___________________________________________________________________________

6/5

6.1-4 Save and Restore application functions

These functions, accessed by selecting Utilities/Save or Utilities/Restore, are used to :

• Save the MMI application to the hard disk or to a diskette. The destination is selected by entering the full path. The file saved must have the extension .M17

• Restore an application which has been saved previously. The source is selected by entering the full path.

6.1-5 Save and Restore character font functions

These functions, accessible by selecting Utilities/Save Application Font or

Utilities/Restore Font, are used to :

• Save the man-machine interface application character font to the hard disk or to a diskette. The destination is selected by entering the full path. The file saved must have the extension .POL

• Restore a character font which has been saved previously. The source is selected by entering the full path.

___________________________________________________________________________

6/6

Additional functions 6

6.1-6 Application conversion functions

Converting a text file to the application

This function is accessed by selecting Utilities/Text file

to Application. It is used to import an application comprising the configuration (except the parameters which can be accessed by passwords as well as the CCX 17 type), the status messages, the alarm messages, the command keys and the status message groups from a previously generated ASCII file to the current application.

The source is selected by entering the full path. The character font set is not imported.

The imported file overwrites the current application.

The user can generate an ASCII file containing an MMI application by using a text editor.

The language for this entry and its syntax are defined in the Help software.

A file can only be imported if it is consistent with the application (CCX 17 type and configuration parameters accessible by password) which is receiving it. Otherwise, it cannot be imported.

Converting the application to a text file

This function is accessed by selecting Utilities/

Application to Text File. It is used to export an application comprising the configuration (except the parameters accessible by passwords as well as the CCX 17 type), the status messages, the alarm messages, the command keys and the status message groups from the current application to an ASCII file. The character font set is not exported.

The destination is selected by entering the full path.

___________________________________________________________________________

6/7

6.1-7 Documenting an application

This function is started by clicking on this icon or by selecting the

Documentation menu and enables a structured file on the

MMI application to be created. This file contains :

• a title page which serves as a header for the file and enables any general information relating to the application to be collected,

• the configuration of the operator panel assigned to the application,

• the configuration of the Data link (configuration for communication via shared memory, etc),

• the list of characters modified in relation to the system font,

• the list of status messages with all their characteristics,

• the list of alarm messages with all their characteristics,

• the assignment of the operator panel command keys,

• the message/group cross references,

• the symbol/message cross references,

• the contents page for the file,

• a footer at the bottom of every page, containing :

- the application name

- the section name

- the document creation date

- the page number

- two blank items which can be defined by the user.

___________________________________________________________________________

6/8

Additional functions 6

Entering the title page

Information relating to the title page is entered after selecting the Documentation/Enter

Information/Title page function. When this documentation function is used for the first time, the title page is empty :

Cancel

OK cancels the entries and returns to the initial program screen.

saves the information in the MMI17.TIT file. The end of the save is indicated by the screen below.

If the MMI17.TIT file already exists, a message requesting confirmation of file replacement is displayed.

___________________________________________________________________________

6/9

Entering the footer

Information relating to the footer is entered after selecting the Documentation/Enter

Information/Footer function. When this documentation function is used for the first time, the footer is empty :

Cancel

OK cancels the entries and returns to the initial program screen.

saves the information in the MMI17.CRT file. A message indicates the save is complete. If the MMI17.CRT file already exists, a message requesting confirmation of file replacement is displayed.

Generating the documentation

The Documentation/Generate function enables the documentation file to be created on the programming terminal hard disk. This file can be viewed, printed, deleted or integrated in the station documentation file using the XTEL-DOC tool. The screen displayed enables the items which will form part of the documentation file to be selected.

Cancel cancels the request and returns to the initial program screen.

OK starts the save procedure of the documentation file in the MMI17.DOC

file (version 2.3) or the NomAppli.DOC file (version 2.4). A series of messages indicates progress and the end of the save.

Note :

The character font for the documentation file is always 437. It is not related to the application font.

___________________________________________________________________________

6/10

Additional functions 6

Viewing the documentation

The Documentation/View function enables the documentation file saved to the hard disk to be displayed on-screen. In order for it to be viewed, the file must have previously been generated.

Printing the documentation

The file is printed by clicking on this icon or by selecting the Documentation/Print function. The screen offers a selection of printers which can be chosen.

Deleting the documentation

The Documentation/Delete function enables the documentation file saved to the programming terminal hard disk to be deleted, after confirmation (MMI17.DOC

file for version 2.3 or NomAppli.DOC for version 2.4).

Multi-application documentation

The Multi-application documentation function can be used to create, view or print a documentation file from the concatenation of several application files :

• Multi-application documentation/Generate creates the file on the programming terminal hard disk using the list of station documentation. If the station does not contain any documentation files, the menu is grayed out.

The selected files are concatenated in alphabetical order. If a CONCAT.DOC file already exists on the hard disk, it will be deleted.

• Multi-application documentation/View displays the documentation file from the concatenation of several application files on screen (CONCAT.DOC file).

• Multi-application documentation/Delete deletes the CONCAT.DOC file from the programming terminal.

• Multi-application documentation/Print prints the concatenated documentation file

(CONCAT.DOC file).

___________________________________________________________________________

6/11

6.1-8 Reconfiguring an OFB

This function, launched by selecting Utilities/Reconfigure OFB, is used to reconfigure the application OFBs according to the station configuration.

It is run automatically when an existing application is opened.

If the application contains OFBs which have not been installed, the list of variables which have not been installed appears.

These variables cannot be reconfigured.

___________________________________________________________________________

6/12

Additional functions 6

6.2

Transferring an application

6.2-1 Local transfer : terminal to CCX 17

This function is started by clicking on this icon or by selecting Transfer/

Local/Terminal to CCX 17 and enables the current application to be partially or totally transferred in local mode (ie via a direct link between the programming terminal and the operator panel) to the CCX 17.

The different types of connection between the terminal and the operator panel are described in the CCX 17 installation manual.

In order for the transfer operations in local mode to become automatically operational, the

UNI-TELWAY driver (V5 level minimum), specific to the operating system used, must be installed on the programming terminal. If this is not the case, the error message opposite is displayed.

Once the function has been started, a screen enables selection of the parameters to be transferred :

Complete application

Selects the entire operator panel configuration.

Configured data

Only selects the data configured in the application.

Transferring part of the application parameters requires the relevant elements to be selected.

OK starts the transfer of the selected parameters.

Cancel cancels the transfer request and returns to the initial program screen.

___________________________________________________________________________

6/13

Comment :

It is possible to carry out a partial transfer of status messages, alarm messages or command keys from :

• the selection screen described previously,

• the windows relating to entry of status messages, alarm messages or command keys, once the elements to be transferred have been selected (using the keyboard or the mouse) and the required transfer function has been activated.

Cancel starts the transfer of the selected parameters.

cancels the transfer request and returns to the entry screen in use.

6.2-2 Local transfer : CCX 17 to terminal

This function, started by selecting Transfer/Local/CCX 17 to terminal, enables the complete application contained in the CCX 17 to be transferred in local mode (ie via a direct link between the programming terminal and the operator panel) to the programming terminal.

As with the terminal to operator panel transfer, the UNI-TELWAY driver is required.

A message indicates to the user that the transfer is in progress. In the same way, if an application is present in the terminal, a message requests confirmation to replace it. To avoid any overwriting, it is recommended that a new application be opened before this transfer is started.

___________________________________________________________________________

6/14

Additional functions 6

6.2-3 Remote transfer : Choice of CCX 17 address

Before starting the remote transfer (in whichever direction), the user must specify the address of the operator panel being used. To do this, start the Transfer/Remote/

CCX 17 Address function. The value of this address is directly linked to the type of network on which the programming terminal and the CCX 17 operator panel are connected :

Examples of screens

UNI-TELWAY protocol FIPIO protocol

Operator panel protocol

Specifies the current protocol for the remote operator panel.

PLC address

Specifies the PLC address on which the CCX 17 operator panel is connected, in the form "network number.station number" when the remote PLC is on another network. This field is set by default to the station address. The network number must be between 0 and 127, the station number between 0 and 63 (address 0,254 is also allowed).

CCX 17 address

Only offered if the chosen protocol is UNI-TELWAY, this field specifies the address of the operator panel. There are two possibilities :

• the operator panel is connected via an SCM UNI-TELWAY module, enter the module slot (rack number and module number) and the data link address of the operator panel on the bus plus 100. The

Rack/Module value and the data link address is entered in decimal.

If, for example, the SCM module is installed in rack 4 at slot 1 and the operator panel is connected at data link address 23, the

"Operator panel address" field has the value 65,123 (ie 41 in hexadecimal = 65 in decimal),

• the operator panel is connected via a UNI-TELWAY port integrated into the processor, this field must then only indicate the data link address of the operator panel plus 100.

FIPIO connection point

Only offered if the chosen protocol is FIPIO, this field specifies the

CCX 17 connection point on the FIPIO fieldbus (the possible values are between 1 and 62).

___________________________________________________________________________

6/15

6.2-4 Remote transfer : terminal to CCX 17

This function is started by clicking on this icon or by selecting Transfer/

Remote/Terminal to CCX 17 and enables the current application to be transferred partially or totally via a communication network (MAPWAY,

FIPWAY or ETHWAY type) to the CCX 17 operator panel.

The programming terminal is connected to a PLC architecture element (PLC terminal port, network, etc) and can access, due to the transparent network, all the elements of the architecture.

The active communication driver is specified in the Communication-Driver menu of the initial XTEL or MINI-XTEL main window.

If the user has not specified the CCX 17 address, the screen described in section

6.2-3 is offered.

6.2-5 Remote transfer : CCX 17 to terminal

This function, started by selecting Transfer/Remote/CCX 17 to terminal, enables the complete application contained in the CCX 17 to be transferred to the programming terminal via a communication network (MAPWAY, FIPWAY or ETHWAY type).

The programming terminal is connected to a PLC architecture element (PLC terminal port, network, etc) and can access, due to the transparent network, all the elements of the architecture.

Before starting the transfer, the user must select the address of the operator panel and of the PLC to which it is connected. For more details relating to this procedure, see section 6.2-3.

Once this function has been confirmed, a message indicates to the user that the transfer is in progress. In the same way, if an application is present on the terminal, a message requests confirmation to replace it. To avoid any overwriting, it is recommended that a new application be opened before the transfer is started.

___________________________________________________________________________

6/16

Additional functions 6

6.2-6 Examples

• The operator panel is connected via a UNI-TELWAY port integrated in the

processor : the terminal can be connected to the network as well as the terminal port.

R2/S4

FIPWAY / ETHWAY / MAPWAY

R2/S8

Device X

The parameters must be :

Operator panel protocol : UNI-TELWAY Slave

PLC address : 2.8 (network 2, station 8)

Operator panel address : 112 (data link address 12).

Data link address 12

CCX 17

• The operator panel is connected to an SCM module and to another network : the terminal can be connected to the network as well as the terminal port.

R5/S14

FIPWAY / ETHWAY / MAPWAY

R5/S3 R5/S7

R2/S4 R14/S6 R14/S21

Rack 4 / Module 6

Device X

The parameters must be :

Operator panel protocol : UNI-TELWAY Slave Data link address 9

PLC address : 14.21 (network 14, station 21)

Operator panel address : 70.109 (46 hex = 70 decimal).

CCX 17

___________________________________________________________________________

6/17

After entering the operator panel address, the Transfer/Remote/Terminal to CCX 17 function enables the current application to be transferred partially or totally to the CCX

17 operator panel.

As with transfers in local mode, a screen is displayed for selecting the parameters to be transferred. The procedure is identical. For more details, see section 6.2-1.

• The operator panel is connected to a FIPIO fieldbus : the terminal can be connected to the network as well as the terminal port.

R2/S10 R2/S2 R2/S6

R6/S1 R6/S2

The parameters must be :

Operator panel protocol : FIPIO,

PLC address : 6.2 (network 6, station 2),

FIPIO connection point : 16.

C o n n e c tion point

CCX 17

___________________________________________________________________________

6/18

7 Communication via the mailbox

7.1

Programming parameters

Reminders :

Once the PL7-MMI 17 software has loaded the various types of message into the CCX 17 operator panel, the PLC application program can communicate with the operator panel via a mailbox system which uses internal word tables. The various communication principles and acknowledgment mechanisms, for status messages as well as alarm messages, are described in section 4.2. The section below only describes the coding of lamps on the illuminated indicator bank.

The mailbox used in the PLC word memory enables various commands to be sent to the

CCX 17 operator panel. It contains a command table structured as follows :

Wi Indicator lamp status

Wi+1 Number of group to be displayed

Wi+2 Number of 1st status message to be displayed

Wi+3 Number of 2nd status message to be displayed

...

Number of last status message to be displayed

Both the start of this table and its length are defined by the user when the application is created using PL7-MMI 17 (see section 5.2-2).

Managing the status of lamps on the illuminated indicator bank

The first word in the table assigned to the mailbox zone contains the coding information for each indicator lamp.

• bits 0 to 3 : status of green indicator lamp

• bits 4 to 7 : status of yellow indicator lamp

• bits 8 to 11 : status of red indicator lamp.

The status of these indicator lamps is coded on these four bits as follows :

• 0000 : indicator lamp status unchanged, enabling each indicator lamp to be controlled separately

• 0001 : indicator lamp off

• 0010 : indicator lamp on

• 1111 : indicator lamp flashing.

___________________________________________________________________________

7/1

___________________________________________________________________________

7/2

8 Communication via text blocks

8.1

List of commands

Reminder :

Once the PL7-MMI 17 software has loaded the various types of message into the CCX 17 operator panel, the PLC application program can communicate with the operator panel by sending specific commands via text function blocks.

TxTi

As a general rule, any command destined for a CCX 17 operator panel is made up of a 16-bit word representing the command number, possibly followed by one or several parameters associated with this command.

Whatever type of command is sent, the CCX 17 operator panel systematically sends a confirmation to the transmission text block (to TXTi,V parameter for PL7-3 language or to TXTi,R parameter for PL7-2 language).

Details on text block parameter coding are given in section 8.2.

The table on the next two pages shows the various options for communication via text blocks and their associated commands.

___________________________________________________________________________

8/1

Command Function Parameters

Clear screen

Clear line

Clears the entire screen and halts updating Command : 1 of variables displayed on-screen.

Clears the contents of the selected line. Halts Command : 2 updating of variables displayed on the line.

Line number

(Clearing a message written in double height requires two lines to be cleared).

Display a CCX 17 message

Display a CCX 17 group

Displays the specified message.

Displays the specified group.

Command : 3

Message number

Command : 5

Group number

Display a PLC message Displays a message which exists in the PLC Command : 6

(for more details about command parameters, Message text see section 8.2-2).

Display lamps on the illuminated indicator bank

Print entry logs

Causes the CCX 17 operator panel indicator Command : 8

lamps to light up, be extinguished or to blink Indicator lamp

(for more details, see section 8.2-4).

status

Prints the entry logs

( only available on V2.0 upwards)

Command : 9

Clear status message log

Print alarm logs

Clear alarm message log

Clears messages previously archived in the Command : 10 operator panel memory.

Prints the alarm logs

( only available on V2.0 upwards)

Command : 11

Clears alarm messages previously archived Command : 13

(in chronological order and on each occurrence) in the operator panel memory

Assign command keys Assigns a PLC bit to a command key on the Command : 14 operator panel.

Key number

Bit number

Reset command key assignment

Dissociates a PLC bit previously assigned to a command key.

Command : 15

Key number

Open / close alarm relay

Write Date and Time to the operator panel

Alarm relay management by the application program (toggle mode).

time with that of the PLC.

Reboot operator panel Restarts the CCX 17.

Enable / disable command keys

Enables or disables management of command keys (toggle mode).

Command : 16

Authorizes resynchronization of the date and Command : 18

Command : 19

Command : 20

Enable / disable alarm Enables or disables alarm message archiving Command : 21 message archiving (toggle mode).

___________________________________________________________________________

8/2

Communication via text blocks 8

Command Function

Message entry, controlled by the PLC

Enables the entry made by the operator to be retrieved for processing at a later date.

program (the message The value of the entry is sent to the text is in the CCX 17) block reception table. The user does not press the MOD key.

Parameters

Command : 22

Message number

Message entry, not checked and not synchronized with the

PLC program

Enables the entry made by the operator to be Command : 24 retrieved for processing at a later date.

The value of the entry is sent back on request.

Message number

Read operator panel status

Informs the text block reception table about the operator panel hardware status

(see section 10.1-2).

Command : 25

Read version and type Informs the text block reception table about Command : 26 of operator panel the software version and type of operator panel (see section 10.1-2).

Activate an operator panel Displays the specified message, if it alarm message

Command : 27 exists in the operator panel and is configured Message number to be displayed.

Archives the message in the alarm zone.

Alarm relay is closed when the first alarm appears.

Activate a PLC alarm message

Displays the specified message, if it exists in Command : 28 the PLC and is configured to be displayed.

Message text

Archives the message in the alarm zone.

For more details see section 8.2-3.

Deactivate an operator Removes the message from the active alarm Command : 29 panel alarm message zone and memorizes the date and time at Message number which the fault disappeared.

The alarm relay opens when the last alarm is acknowledged.

Deactivate a PLC alarm message

Removes the message from the active alarm Command : 30 zone and memorizes the date and time at which the fault disappeared. For more details see section 8.2-3.

Message number

Assign all the operator panel command keys to internal bits

Configures, with one command, all the operator Command : 31 panel command keys (4 or 8 keys depending Bit No. assigned to K1 on the type of CCX 17). The additional Bit No. assigned to K2 parameters indicate the indexes or bit numbers assigned to the various keys

(K1 to K8).

........

Bit No. assigned to K8

___________________________________________________________________________

8/3

Command Function Parameters

Configure all the operator panel command keys

Enables to the operator panel command keys Command : 32 and their operating modes to be configured Key to operate

(see section 8.2-5) Operating mode

(only available on V2.0 upwards) Bit index

Entry of a message checked by the PLC

Enables the entry made by the operator Command : 33 to be retrieved for processing at a later date. Message text program (the message The value of the entry is retrieved to the text is in the PLC) block reception table. The user does not press the MOD key.

(see section 8.2-6).

(only available on V2.0 upwards)

Configure the mailbox Configure the sampling time of the mailbox Command : 34 and specify its contents.

Period

(See section 8.2-7).

(only available on V2.1 upwards)

Length

Contents

Alarm transfer Contact the Technical Support for more information. (Only available on V2.4 or later)

Command : 35

___________________________________________________________________________

8/4

Communication via text blocks 8

8.2

Programming parameters

8.2-1 Text function block parameters

The text block used must have the following characteristics :

• CPL type LOCAL text block

• TXTi,C = H'00FC' (unsolicited data request)

• TXTi,L = transmission table length, in bytes. The minimum length is one word (for the majority of commands), the maximum length depends on the number of parameters to be sent when using commands to display a status or alarm message issued by the

PLC.

• TXTi,M = CCX 17 operator panel address. This depends on the type of PLC

UNI-TELWAY module :

- If the module is integrated in the processor, TXTi,M must take the hexadecimal value H'FF' followed by the operator panel address (in hexadecimal) + H'64'. If, for example, the operator panel is at address 12 (12 = H'000C'), TXTi,M has the value

H'FF70'.

- If it is a TSX SCM... module, TXTi,M corresponds to the module location (rack and module number) followed by the operator panel address (in hexadecimal) + H'64'.

If, for example, the TSX SCM... module is in rack 0 at slot 5 and the operator panel is at address 6 (6 = H'0006'), TXTi,M has the value H'056A'.

• TXTi,V or TXTi,R contain the request code for operator panel response (H'00FC').

• Transmission table (in bytes) : The first word in the text block transmission table contains the command to be sent (coded in decimal), and the following words are assigned to any parameters which may be associated with the command (for example key number and bit number, etc).

• Reception table (in bytes) : this contains two words (three words in the case of commands 25 and 26, see section 10.1-2) :

- a status word giving the result of the exchange (H'07FE' if the exchange is successful, H'07FD' if unsuccessful),

- an additional status word which goes to 0 if the operation was successful and whose bits at 1 in the event of an error have the following meaning :

Bit 0 = 1 : Command not recognized by the CCX 17,

Bit 1 = 1 : Command buffer full,

Bit 2 = 1 : Command size (in bytes) less than the minimum size required,

Bit 3 = 1 : Command blocked (transfer in progress),

Bit 5 = 1 : Invalid command.

___________________________________________________________________________

8/5

8.2-2 Command to display a PLC status message

It is possible to construct status messages from the PLC application and to transfer them via a text block in order to display them on the CCX 17 operator panel screen.

This is done using the command "Display a PLC status message". Its structure is as follows :

• The first word in the text block transmission table must contain the number 6

(command number = 6).

• The following words must contain the text of the message to be sent, including the underscores "_" representing the expected characters when a variable is displayed or entered. This text can have a maximum of 40 characters.

If the text has an odd number of characters, the last byte equals 0, if the text has an even number of characters and has less than 40 characters, the last word must take the value 0.

• A word which contains the number of the line where the message must be displayed.

• A word which contains the number of the column where the start of the message must be displayed.

• A zone of four characters (two words) containing the message characteristics and structured as follows :

- the first character (in upper case) corresponds to the video attribute :

B = blinking

R = reverse video

A = blinking and reverse video

N = no particular attribute

- the second character (in upper case) corresponds to the size of the character font :

S = standard size

D = double height and double width

- the third character (in upper case) corresponds to the printing option :

Y = yes

N = no

- the fourth character must be a blank (space).

If the user does not wish to display a variable, the next word must be at 0 (in this case the rest of the parameters are ignored), otherwise, the following parameters must be added :

• A word which contains the position of the variable to be displayed, counted according to the number of characters relative to the start of the message (standard or double characters).

• A word which contains the number of characters to be displayed.

• A word which contains an additional command :

0 : no command

1 : clear the screen

2 : clear the line prior to display

24 : unrestricted operator entry authorized after display.

___________________________________________________________________________

8/6

Communication via text blocks 8

• A word which contains the value H'0030'.

• Two words (in upper case) which contain the type of operator entry field :

M'BIT_' (_ represents a space) for a bit type

M'ANA_' (_ represents a space) for a word type

M'LNG_' (_ represents a space) for a double word type

M'STR_' (_ represents a space) for a string type

M'LST_' (_ represents a space) for a word type index

M'DAY_' (_ represents a space) for a date type

M'HOU_' (_ represents a space) for an hour type.

• A word which contains the value 0 (PL7 object type).

• A word (in upper case) which contains the type of variable to be displayed :

M'B_' (_ represents a space) for a bit type

M'W_' (_ represents a space) for a word type

M'DW' for a double word type.

• A word which contains the address of the variable to be displayed.

• Two words (in upper case) which contain the display format of the variable, structured as follows :

- byte 1 contains information specifying whether the variable is signed (+ sign), or not

(space),

- bytes 2 and 3 contain information specifying the number of digits to be displayed after the decimal point for an ANA or LNG type format, or the number of consecutive words to be read in the case of a string type format,

- byte 4 contains information indicating the type of display :

D for decimal

A for ASCII

B for bargraph

• A word (in upper case) which defines whether the variable must be updated or not :

M'Y_' (_ represents a space) for yes

M'N_' (_ represents a space) for no

• A word (in upper case) which contains the field attribute :

M'I_' (_ represents a space) for Increment

M'L_' (_ represents a space) for Normal

M'N_' (_ represents a space) for no attribute.

• A word which indicates whether the variable is limited or not :

0 for an unlimited variable

1 use minimum limit only

2 use maximum limit only

3 use both minimum and maximum limits.

• A double word which contains the value of the minimum limit.

• A double word which contains the value of the maximum limit.

• A double word which contains the value of the increment.

___________________________________________________________________________

8/7

8.2-3 Command to display a PLC alarm message

It is possible to either activate or deactivate alarm messages from the PLC application and to transfer them via a text block in order to display them on the CCX 17 operator panel screen.

This is done using the commands "Activate a PLC alarm message" (command 28) or

"Deactivate a PLC alarm message" (command 30).

Activate an alarm message

The structure of the parameters to be transmitted is as follows :

• The first word in the text block transmission table must contain the number 28

(activate).

• A word containing a theoretical number attributed to the alarm message (this word will serve to deactivate the alarm if required). The value of the word must be between 900 and 999.

• The following words must contain the text of the message to be sent, including the underscores "_" representing the expected characters when the variable is displayed.

This text can have a maximum of 40 characters.

If the text has an odd number of characters, the last byte equals 0, if the text has an even number of characters and has less than 40 characters, the last word must take the value 0.

• A zone of three words containing the message characteristics and structured as follows :

- the first character (in upper case) corresponds to the size of the character font :

S = standard size

D = double height and double width

- the second character (in upper case) corresponds to the printing option :

Y = yes

N = no

- the second word (in upper case) corresponds to the on-screen overprint option :

- Y followed by a space + yes

N followed by a space + no

- the third word corresponds to the type of field (=0 for no associated variables).

If the user does not wish to display a variable, the next word must be at 0, otherwise, the following parameters must be added :

• A word which contains the position of the variable to be displayed, counted according to the number of characters relative to the start of the message (standard or double characters).

• A word which contains the number of characters to be displayed.

___________________________________________________________________________

8/8

Communication via text blocks 8

• A word which contains the command type :

- 0 = no command,

- 2 = clears the line before displaying.

• A word containing the value H'0030',

• Two words (in upper case) which contain the type of entry field :

M'BIT_' (_ represents a space) for a bit type

M'ANA_' (_ represents a space) for a word type

M'LNG_' (_ represents a space) for a double word type

• A word which contains the value 0,

• A word (in upper case) which contains the type of variable to be displayed :

M'B_' (_ represents a space) for a bit type

M'W_' (_ represents a space) for a word type

M'DW' for a double word type,

M'_ _' (_ represents a space) for no type.

• A word which contains the address of the variable to be displayed.

• Two words (in upper case) which contain the display format of the variable, structured as follows :

- byte 1 contains information specifying whether the variable is signed (+ sign), or not

(space),

- byte 4 contains information indicating the type of display :

N for no format

D for decimal

A for ASCII

Deactivate an alarm message

The structure of the parameters to be transmitted is as follows :

• The first word in the text block transmission table must contain the number 30

(deactivate the alarm),

• A word containing the theoretical number attributed to the alarm when programming command 28. The value of this word must be between 900 and 999.

___________________________________________________________________________

8/9

8.2-4 Display command for illuminated indicator bank

It is possible to define the status of the lamps on the illuminated indicator bank from the

PLC application and to transfer it via a text block. This is done using the command

"Display lamps on the illuminated indicator bank". Its structure is as follows :

• The first word in the text block transmission table must contain the number 8

(command number = 8).

• The second word indicates the coding of each indicator lamp :

- bits 0 to 3 : status of green indicator lamp

- bits 4 to 7 : status of yellow indicator lamp

- bits 8 to 11 : status of red indicator lamp.

The status of these indicator lamps is coded on these four bits as follows :

- 0000 : indicator lamp status unchanged, enabling each indicator lamp to be controlled separately

- 0001 : indicator lamp off

- 0010 : indicator lamp on

- 1111 : indicator lamp flashing.

Example:

If the status word of the indicator lamp = H''02F1', i.e. 0000 0010 1111 0001

The green indicator lamp switches off, the orange indicator lamp flashes and the red indicator lamp switches on.

___________________________________________________________________________

8/10

Communication via text blocks 8

8.2-5 Configure command keys

It is possible to define the entire command key configuration (with or without assigned bit, key operating mode, etc). Its structure is as follows :

• The first word in the text block transmission table must contain the number 32

(command number = 32),

• The second word contains the list of keys to configure. Each command key is coded on a bit :

- 0 = command key not assigned to an internal bit (for using RIW bits and discrete outputs),

- 1 = command key assigned to an internal bit.

Bit 0 = command key 1,

Bit 1 = command key 2,

••••,

Bit 7 = command key 8,

• Two words containing the operating mode of each command key. Each key is coded on two bits :

- 00 = Reset,

- 01 = edge operating mode,

- 10 = toggle operating mode

- 11 = reserved.

Bit 0/1 = command key 1,

Bit 2/3 = command key 2,

••••,

Bit 14/15 = command key 8.

• Eight words containing the index of internal bits assigned to command keys :

- word 1 = index of bit assigned to key 1,

- word 2 = index of bit assigned to key 2,

- ••••,

- word 8 = index of bit assigned to key 8,

___________________________________________________________________________

8/11

8.2-6 Entering a message controlled by the PLC

• The first word in the text block transmission table must contain the number 33

(command number = 33),

• The following words must contain the text of the message to be sent, including the

"underscores" _ representing the expected characters when the variable is displayed or entered. This text can have a maximum of 40 characters.

If the text has an odd number of characters, the last byte equals 0, if the text has an even number of characters and has less than 40 characters, the last word must take the value 0.

• A word which contains the number of the line where the message must be displayed,

• A word which contains the number of the column where the start of the message must be displayed,

• A word which contains the character attribute and the size :

M'NS' = no attribute, standard size,

M'ND' = no attribute, double size,

M'BS' = blinking, standard size,

M'BD' = blinking, double size,

M'RS' = reverse video, standard size,

M'RD' = reverse video, double size,

M'AS' = reverse video and blinking, standard size,

M'AD' = reverse video and blinking, double size.

• A word which contains the printer attribute. Always takes the value :

M'N_' (_ represents a space),

• A word which contains the position of the variable to be displayed, counted according to the number of characters relative to the start of the message (standard or double characters),

• A word which contains the number of characters to be displayed,

• A word which contains an additional command :

0 : no command,

24 : unrestricted operator entry authorized after display.

• A word which contains the value H'0030',

• A double word (in upper case) which contain the type of operator entry field :

M'BIT_' (_ represents a space) for a bit type,

M'ANA_' (_ represents a space) for a word type,

M'LNG_' (_ represents a space) for a double word type.

• A word which contains the value 0,

• A word (in upper case) which contains the type of variable to be displayed :

M'B_' (_ represents a space) for a bit type

M'W_' (_ represents a space) for a word type

M'DW' for a double word type,

• A word which contains the address of the variable to be displayed.

___________________________________________________________________________

8/12

Communication via text blocks 8

• Two words (in upper case) which contain the display format of the variable, structured as follows :

- byte 1 contains information specifying whether the variable is signed (+ sign), or not

(space),

- byte 4 contains information indicating the type of display :

D for decimal,

A for ASCII,

N for no format,

• A word (in upper case) which defines whether the variable must be updated or not :

M'Y_' (_ represents a space) for yes,

M'N_' (_ represents a space) for no,

• A word (in upper case) which contains the field attribute :

M'I_' (_ represents a space) for Increment,

M'L_' (_ represents a space) for Normal,

M'N_' (_ represents a space) for no attribute,

• A word which indicates whether the variable is limited or not :

0 for an unlimited variable,

1 use minimum limit only,

2 use maximum limit only,

3 use both minimum and maximum limits,

• A double word which contains the value of the minimum limit,

• A double word which contains the value of the maximum limit,

• A double word which contains the value of the increment.

___________________________________________________________________________

8/13

8.2-7 Configuring the mailbox

Command structure

• the first word comprises the command to be sent (coded in decimal),

• the second word indicates the sampling value (modulo 400ms),

0 -> no sampling

1 -> sampling at 400ms

2 -> sampling at 800ms

- - - - - - - - - - - - - - - - - - - - - - - - - - -

600 -> sampling at 5min

• the third word indicates the length of the mailbox,

• the following words represent the contents of the mailbox.

Response structure

This contains :

• the "return code" word giving the result of the exchange

H'07FE' if the exchange is correct,

H'07FD' if there is an error.

• an additional status word which takes the value :

0 if the operation has been performed correctly,

≠

0 if there is an error. In this case, the bits set to 1 indicate :

Bit 0 = 1 : Command not recognized by the CCX17,

Bit 1 = 1 : Command buffer full,

Bit 2 = 1 : Command size (in bytes) smaller than the minimum allowed,

Bit 3 = 1 : Command not allowed (transfer in progress),

Bit 4 = 1 : "Length" field greater than the max length of the mailbox,

Bit 5 = 1 : Incorrect command,

Bit 6 = 1 : Message number out of limits, the high order byte indicates the

last invalid message,

Bit 7 = 1 : Group number outside limits,

Bit 8 = 1 : Impossible to process the command as the CCX17 is displaying a

system screen.

___________________________________________________________________________

8/14

Chapter 9

9 Application examples

9.1

Examples

The various examples shown in the rest of this section, involving the same MMI application on a CCX 17-30 LPS operator panel, can be connected either on FIPIO or on UNI-TELWAY :

• The application is configured entirely by PL7-MMI 17, therefore communication is either via mailbox or text blocks.

• The application is totally managed by text blocks.

Description of the application Fixed message

Use of the command keys

Oven 4

Use of the c o m m a n d keys

Stop

Updated variable

Run

% Humidity :

Set point = 326

Temperature = 325

Variable to be entered

Bargraph display

Assigning the PLC variables

• B0 = Run key (causes the CCX 17 green indicator lamp to flash).

• B2 = Stop key (causes the CCX 17 red indicator lamp to flash).

• W0 = setpoint (value both read and written).

• W10 = temperature measurement (read value).

• The amount of humidity in bargraph form (read value) is in internal word W20 for a CCX

17 connected on UNI-TELWAY and in a ROW word for a CCX 17 connected on FIPIO.

___________________________________________________________________________

9/1

CCX 17 connected on UNI-TELWAY

The CCX 17 operator panel is connected as shown below (the programming terminal can also be directly connected to the network) :

Network 1 Station n Station 1

Processor with integral

SCI link address 1

CCX 17 connected on FIPIO

The CCX 17 operator panel is connected as shown below (the programming terminal can also be directly connected to the network) :

Network1 Station n Station 1

Connection point 16

___________________________________________________________________________

9/2

Application examples 9

9.2

Application configured by PL7-MMI 17

9.2-1 Configuring the application

The application includes six status messages assigned to two groups of messages, three alarm messages, management of two command keys and modification of the status of the red and green indicator lamps of the operator panel.

Configuring the protocol

Communication via UNI-TELWAY Configuration by FIPIO

Configuring the Data link

• W150 is the status word written by the CCX 17 to the PLC.

• Acknowledgment of alarms must be confirmed,

• The mailbox zone is installed from B200 for the alarms (four bits long) and from W200 for the status messages (10 words long).

• Management of the acknowledgments on read and write.

___________________________________________________________________________

9/3

Configuring the status messages

The messages are as follows :

• Oven 4 (status message 1), with line clear.

• Run (status message 2), with line clear.

• Stop (status message 3), without line clear since Stop is on the same line as the Run message.

• Setpoint = ----

C (status message 4, reading and writing word W0 in decimal), with entry of the variable (RKB). Entry is incremental (minimum limit 100, maximum limit

350 and increment 10).

• Temperature = ----

C (status message 5, displaying word W10 in decimal), with line clear.

• % Humidity = (status message 6, displaying word W20 as a bargraph for UNI-

TELWAY or ROW 16,0,5 for FIPIO), with line clear.

Status message 1

___________________________________________________________________________

9/4

Status message 2

Application examples 9

Status message 3

Status message 4

___________________________________________________________________________

9/5

Status message 5

Status message 6 (UNI-TELWAY)

Status message 6 (FIPIO)

___________________________________________________________________________

9/6

Application examples 9

Configuring the alarm messages

The application manages three alarms :

• a single message (double size) : Emergency stop,

• a message displaying a variable : Overheating oven 4 = ----

C (displaying word W125 in decimal),

• a message displaying a variable : Insufficient humidity = ---- % (displaying word W20 in decimal).

Each alarm is displayed on-screen when it occurs.

Alarm message 1

Alarm message 2

___________________________________________________________________________

9/7

Alarm message 3

Configuring the status messages groups

• The first group includes the following status messages :

- Oven 4 (status message 1)

- Run (status message 2)

- Stop (status message 3)

- Setpoint = ----

C (status message 4),

• The second group includes the following status messages :

- Temperature = ----

C (status message 5)

- % Humidity = (status message 6).

The first group is displayed by default with clear screen option. The second group is displayed when requested by the user. It is displayed following the first group, so it must not include the clear screen option.

Group 1

___________________________________________________________________________

9/8

Group 2

Application examples 9

Configuring the command keys

The two command keys are configured in an edge type operation. One controls the internal bit B0 (Run key), the other controls the internal bit B2 (Stop key).

___________________________________________________________________________

9/9

Transferring the application

Once the application is configured and saved, it must be transferred to the CCX 17 operator panel. In the example shown, the operator panel is connected either on

UNI-TELWAY or on FIPIO.

Transfer on UNI-TELWAY

The CCX 17 is at address link 1. The processor has an integrated SCI link.

The PLC is connected on a network at the following address : Network 1, Station 5.

The operator panel address is 100 + address link, or 255.101,

The transfer screen enabling choice of operator panel address is thus :

Transfer on FIPIO

The CCX 17 is at connection point 16.

The PLC is connected on a network at the following address : Network 1, Station 5.

The connection point is 16,

The transfer screen enabling choice of operator panel address is thus :

___________________________________________________________________________

9/10

Application examples 9

9.2-2 Exchanges via mailbox

Managing the status messages

In the example shown, the mailbox structure is as follows :

Command table

W200 Status of the indicator lamps

W201 No. of the group to be displayed

W202 No. of the 1st message to be displayed

W203 No. of the 2nd message to be displayed

...

W209 No. of the last message to be displayed

Acknowledge on read table

W210 Status of the indicator lamps displayed

W211 No. of the group displayed

W212 No. of the 1st message displayed

W213 No. of the 2nd message displayed

...

W219 No. of the last message displayed

The application program contained in the PLC must therefore update the command table according to the process parameters. The user can check that the requested commands have been correctly executed by analyzing the acknowledge on read table.

Examples of commands :

<Displaying group 2

! IF B10 THEN 2

→

W201; ....

<Managing the Run key (shown by the green indicator lamp)

! IF B0 THEN H'011F'

→

W200; RESET B2; ....

<Managing the Stop key (shown by the red indicator lamp)

! IF B2 THEN H'0F11'

→

W200; RESET B0; ....

Managing the alarm messages

The table reserved for the alarm messages starts at B200 :

• Setting bit B200 to 1 displays and prints alarm message 1 (Emergency stop).

• Setting bit B201 to 1 displays and prints alarm message 2 (Overheating oven 4 : ---

C).

• Setting bit B202 to 1 displays and prints alarm message 3 (Insufficient humidity : ---%).

___________________________________________________________________________

9/11

9.2-3 Exchanges via text blocks

Once the whole application is configured by PL7-MMI 17, the user can, if he wishes, choose text function block communication instead of mailbox communication (example below). These two types of communication can be used in the same application.

Assigning the text function blocks :

• TXT0 is assigned to display group 2.

• TXT1 is assigned to manage the command keys.

• TXT2 is assigned to manage the alarm messages.

The parameters are indicated in the following configuration screen (for communication via UNI-TELWAY) :

Reminders :

Parameter TXTi,M has the value H'xxyy' where xx corresponds to location of the communication module. Where an SCI link is integrated into the processor or in the case of a FIPIO fieldbus it takes the value H'FF'. The parameter yy represents the CCX 17 address, it has the following values :

• Either the CCX 17 link address + H'64' if communicating via UNI-TELWAY.

• Or the CCX 17 connection point number + H'64' if communicating via FIPIO.

The parameter TXTi,C takes the value H'00FC'.

Displaying message group 2

The example shown comprises two groups. Group 1 is displayed automatically

(displayed by default). Displaying group 2 is requested via TXT0 as follows :

___________________________________________________________________________

9/12

Application examples 9

• Reception table : starts at internal word W50 and is 4 bytes long,

• Transmission table : starts at word W52 and comprises two words (4 bytes long). The first word (W52) contains the display group command (command 5) and the second word contains the number of the group to be displayed (W53 = 2).

<Display group 2

! IF RE(I0,0) THEN 5

→

W52; 2

→

W53; EXCHG TXT0;

If an error occurs when the text block is transmitted, the reception table contains two words enabling the source of the error to be defined (see section 8.2-1).

Managing the Run and Stop keys

The example shown comprises two command keys. Displaying the luminous indicator lamps is requested via TXT1 as follows :

• Reception table : starts at internal word W60 and is four bytes long.

• Transmission table : starts at word W62 and comprises two words (4 bytes long). The first word (W62) contains the command to display the luminous indicator lamps

(command 8), and the display is coded in word W63.

<Managing the Run key

! IF B0 THEN 8

→

W62; H'011F'

→

W63; EXCHG TXT1;....

<Managing the Stop key

! IF B2 THEN 8

→

W62; H'0F11'

→

W63; EXCHG TXT1;....

If an error occurs when the text block is transmitted, the reception table contains two words enabling the source of the error to be defined (see section 8.2-1).

Managing the alarm messages

An alarm message is activated and deactivated via TXT2 as follows :

• Reception table : starts at internal word W70 and is four bytes long.

• Transmission table : starts at word W72 and comprises two words (4 bytes long). The first word (W72) contains either the command to activate the alarm (command 27) or the command to deactivate the alarm (command 29). The alarm number (eg alarm

2) to be displayed is coded in word W73.

<Managing activation of alarm 2

! IF RE(I0,1) THEN 27

→

W72; 2

→

W73; EXCHG TXT2;....

<Managing deactivation of alarm 2

! IF FE(I0,1) THEN 29

→

W72; 2

→

W73; EXCHG TXT2;....

If an error occurs when the text block is transmitted, the reception table contains two words enabling the source of the error to be defined (see section 8.2-1).

___________________________________________________________________________

9/13

9.3

Application configured without PL7-MMI 17

9.3-1 Exchanges via text function block

When PL7-MMI 17 software is not available to the user, the PLC can still communicate with the CCX 17 operator panel. Communication is only performed via text function block

(see command details in section 8.2). The transmission table must contain all the parameters of the message to be sent.

Important : The transmission table for the text function blocks used on TSX 17 and

TSX 47-20 PLCs is limited to 30 bytes.

So as not to complicate this example, only the display of message number four

(Setpoint = ----

C) is shown below. This message is representative since it includes an updated variable which can be modified by the operator (incremental entry).

The text block used to send this message is TXT3. Its parameters are indicated below :

• TXT3,M = H'FF65' (CCX 17 address link = 1) for communication via UNI-TELWAY.

If communicating via FIPIO, TXT3,M = 'FF74' (CCX 17 connection point = 16, or H'10'

+ H'FF64' = H'FF74').

• Reception table : starts at internal word W80 and is four bytes long.

• Transmission table : starts at word W82 and includes 34 words (72 bytes long). The first word (W82) contains the status message display command (command 6), and the other words correspond to the message characteristics. The transmission table is detailed on the following page.

Reminder of the message 4 characteristics

Setpoint = ----

C (reading and writing word W0 in decimal format) with incremental entry

(minimum limit 100, maximum limit 350 and increment 10). This message must be positioned at line 4 column 11.

___________________________________________________________________________

9/14

Application examples 9

Transmission table of text block TXT3

In this table "sp" represents a space

W82

W83

W84

W85

W86

W87

W88

W89

W90

W91

W92

W93

W94

W95

W97

W98

W99

W100

W101

= 6

= M'Co'

= M'ns'

= M'ig'

= M'ne'

= M'sp :'

= M'sp_'

= M'_ _'

= M'_ sp'

= M'

= 0

= 4

= 11

= M'NS'

= M'N sp'

H'0030'

W102 = M'AN'

W103 = M'A sp'

W104 = 0

W105 = M'W sp'

Status message display command

Message text

Message text (cont.)

Wait for first character preceded by a space

Wait for second and third character

Wait for last character followed by a space

Message text (end)

End of message marker

Display of message on line 4

Display of message starting at column 11

Message characteristics (no attribute, standard size)

Message characteristics (no print)

Position of the variable from the start of the message

Number of characters to be displayed

Additional command (entry after display)

Reserved value

Type of entry field (AN = start of ANA)

Type of entry field (cont.)

Reserved value

Type of variable to be displayed (W = word type variable)

W106 = 0 Address of the variable to be displayed (W0)

W107 = M'sp sp' Display format (sp for an unsigned variable, sp for start of

W108 = M'sp D' coding of the number of digits after the decimal point)

Display format cont. (sp for end of coding of the number of

W109 = M'Y sp'

W110 = M'I sp'

W111 = 3

DW112 = 100

DW114 = 350

DW116 = 10 digits after the decimal point, D for decimal format)

Variable must be updated

Entry is incremental

Use of the maximum and minimum limits

Minimum limit value

Maximum limit value

Increment value

Once all the values are entered, the text block is started, for example as follows :

< Starting the text block

! IF RE(I0,2) THEN EXCHG TXT3 ; ....

If an error occurs when the text block is transmitted, the reception table contains two words enabling the source of the error to be defined (see section 8.2-1).

___________________________________________________________________________

9/15

___________________________________________________________________________

9/16

10 Appendices

10.1 Additional information

10.1-1 Value of the status word

The status word is defined when the Data link is configured (section 5.2-2). Its contents are as follows :

Bit 0 = 1

Bit 1 = 1

Bit 2 = 1

Bit 3 = 1

Self-tests correct

Application present

Back-up battery correct

CCX 17 memory fault.

The other bits of this status word are not significant.

This word is updated at the end of the CCX 17 initialization procedure.

10.1-2 Report of the commands 25 and 26

The commands 25 and 26 return three report words to the reception table of the text block which sent the request. The first two words are defined in section 8.2-1, and the third word is detailed below.

Command 25 (Operator panel status)

Bit 0 = 1

Bit 1 = 1

Bit 2 = 1

Bit 3 = 1

Self-tests correct

Application present

Back-up battery correct

CCX 17 memory fault.

The other bits of this word are not significant.

This information is only available on the first reading following the initialization of the

CCX 17 operator panel. All bits are at 0 for the following readings.

Command 26 (Software version and type of terminal)

The high order byte for this word corresponds to the type of terminal. It has one of the following values :

• 0000 or H'00' for a CCX 17-20 F,

0001 or H'01' for a CCX 17-20 FW,

0010 or H'02' for a CCX 17-20 FPS

• 0110 or H'06' for a CCX 17-20 L,

0111 or H'07' for a CCX 17-20 LW,

1000 or H'08' for a CCX 17-20 LPS

• 1100 or H'0C' for a CCX 17-30 L,

1101 or H'0D' for a CCX 17-30 LW

1110 or H'0E' for a CCX 17-30 LPS

The low order byte corresponds to the operator panel software version.

E.g. H'10' corresponds to software version 1.0

___________________________________________________________________________

10/1

10.2 Actions possible without using PL7-MMI 17

The PLC can send certain commands to a CCX 17 operator panel even when the operator panel has not been configured and loaded with PL7-MMI 17 software. These commands are as follows :

Command Function Parameters

Clear screen

Clear line

Clears the entire screen and halts updating Command : 1 of variables displayed on-screen.

Clears the contents of the selected line.

Halts updating of variables displayed on the line.

Command : 2

Line number

Display a PLC message Displays a message which exists in the PLC Command : 6

(for more details about command Message text parameters, see section 8.2-2).

Display lamps on the illuminated indicator bank

Print entry log

Causes the CCX 17 operator panel indicator lamps to light up, be extinguished or to blink

(for more details, see section 8.2-4).

Command : 8

Indicator lamp status

Clear message log

Print alarm log

Prints the entry log

(only available on V2.0 upwards)

Prints the alarm log

(only available on V2.0 upwards)

Command : 9

Clears messages previously archived in the Command : 10 operator panel memory.

Command : 11

Clear alarm message log

Clears alarm messages previously archived Command : 13

(in chronological order and on each occurrence) in the operator panel memory

Assign a command key Assigns a PLC bit to a command key on the operator panel.

Command : 14

Key number

Bit number

Reset command key assignment

Open / close alarm relay

Dissociates a PLC bit previously assigned to Command : 15 a command key.

Key number

Alarm relay management by the application Command : 16 program (toggle mode).

Write Date and Time in the operator panel

Reboot operator panel Restarts the CCX 17.

Enable / disable command keys

Authorizes resynchronization of the date and Command : 18 time with that of the PLC.

Enables or disables management of command keys (toggle mode).

Command : 19

Command : 20

Command : 21 Enable / disable message archiving

Read operator panel status

Enables or disables message archiving

(toggle mode).

Informs the text block reception table about the operator panel hardware status

(see section 10.1-2).

Command : 25

___________________________________________________________________________

10/2

Appendices 10

Command Function Parameters

Read version and type Informs the text block reception table about Command : 26 of operator panel the software version and type of operator panel (see section 10.1-2).

Activate a PLC alarm message

Displays the specified message, if it exists in Command : 28 the PLC and is configured to be displayed.

Message text

Archives the message in the alarm zone.

For more details see section 8.2-3

Deactivate a PLC alarm Removes the message from the active alarm Command : 30 message zone and memorizes the date and time at which the fault disappeared. For more details see section 8.2-3

Message text

Configure all the operator panel command keys

Configures, with one command, all the Command : 31 operator panel command keys (4 or 8 keys Bit No. assigned to K1 depending on the type of CCX 17). The Bit No. assigned to K2 additional parameters indicate the indexes ........

or bit numbers assigned to the various keys Bit No. assigned to K8

(K1 to K8)

Enables all the operator panel command keys and their operating mode to be configured (see section 8.2-5)

(only available on V2.0 upwards)

Command : 32

Key to operate

Operating mode

Bit index

Entry of a message controlled by the PLC

Enables the entry made by the operator Command : 33 to be retrieved for processing at a later date.

Message text program (the message is The value of the entry is retrieved to the in the PLC) text block reception table. The operator does not press the MOD key.

(see section 8.2-6).

(only available on V2.0 upwards)

Use of these commands is described in section 8.2.

___________________________________________________________________________

10/3

10.3 Connecting a CCX 17 to a TSX 07

This section describes the stages for loading an application and connecting a CCX 17 and a TSX 07.

• Launch X-TEL and create an Other type station.

• Launch the PL7-MMI 17 software then create a man-machine interface application while taking the following correspondence table into account :

Address in the PL7-MMI 17 application

Correspondence with TSX 07 address

%MW0

%MW1

%MWi

%M0

%M1

%Mi

• Connect the CCX 17 to the programming terminal (see the wiring reference in the CCX

17 installation document).

• Transfer the application to the CCX 17 with the Transfer / Local / Terminal to CCX function (reminder : for a transfer, the UNI-TELWAY driver must be installed in the programming terminal).

• When the transfer is complete, the message "Connection ............." blinks on the

CCX 17.

• Disconnect the Terminal programming link / CCX 17 then connect the CCX 17 to the

TSX 07.

• The CCX 17 is reset and is connected to the PLC.

Note :

MMI 17 under Windows software enables variables to be entered using IEC 11 31 syntax (i.e.

%MWi, %Mi, etc).

10.4 Connecting a CCX 17 to a Series 1000 PLC

To connect a CCX 17 to a Series 1000 PLC and use a FIPIO fieldbus link, see the

"Orphee - Orphee diag : Additive" document.

___________________________________________________________________________

10/4

Appendices 10

10.5 Layout forms to help create messages

The following layout forms, which reproduce the screens of various CCX 17 operator panels (four to eight lines), are very helpful when creating status or alarm messages.

Filled in by the user beforehand, they can quickly determine the best position for a message (line number, column number, etc) and give the user an idea of the final result.

___________________________________________________________________________

10/5

1 2 3 4

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0

1 2 3 4

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0

1 2 3 4

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0

1 2 3 4

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0

1 2 3 4

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0

1 2 3 4

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0

___________________________________________________________________________

10/6

1 2 3 4

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0

Appendices 10

1 2 3 4

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0

1 2 3 4

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0

1 2 3 4

1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0

___________________________________________________________________________

10/7

___________________________________________________________________________

10/8

Helló! Én egy AI chatbot vagyok, amelyet kifejezetten arra képeztek ki, hogy segítsek a Schneider Electric PL7-MMI 17 OS/2 használatában. Alaposan átnéztem a dokumentumot, és segíthetek megtalálni a szükséges információkat, vagy elmagyarázhatom a tartalmat világosan és egyszerűen. Akár konkrét funkciókkal, hibaelhárítási lépésekkel vagy általános használattal kapcsolatban keres útmutatást, nyugodtan tegye fel kérdéseit. Minél több részletet ad meg aggályairól vagy igényeiről, annál pontosabban és hatékonyabban tudok segíteni!

Az asszisztens gépel

Az asszisztens nincs a billentyűzetnél. Kérjük, próbálja újra később.

Hirdetés

Chapter 9

Oven 4

Kapcsolódó

Schneider Electric PL7-MMI 17 WIN, 6.0 User Guide

Schneider Electric PL7-MMI 17 OS/2, 6.0 Benutzerhandbuch

Schneider Electric Software Workshop X-TEL 6.0 User Guide

Schneider Electric PL7-2 Languages User Guide

Schneider Electric Integrated Man-Machine Dialog PL7 MMI 37, 5.2 User Guide

Schneider Electric CCX17, Terminals, Operator's Control Panel Instruction Sheet

Schneider Electric Software Workshop, MINI X-TEL 5.0 User Guide

Schneider Electric PL7 Micro/Junior/Pro Installation Manual

PL7 Junior/Pro User Guide: AI Chat & PDF Access

Schneider Electric SCM Communication, PL7COM 5.0 User Guide

Schneider Electric Adjustment tool ADJUST MMI 37, 5.2 User Guide

Schneider Electric Software Workshop - Tools X-TEL, MINI X-TEL 6.0 User Guide