PLANET IPOE-175 User's manual
Add to My manuals14 Pages
Planet IPOE-175 is a rugged industrial-grade 1-port 60W 802.3bt PoE++ injector designed to provide power and data to PoE-powered devices (PDs) in harsh environments. It features an IP67-rated aluminum case for protection against dust, water, and other outdoor elements. With a wide input voltage range of 24-56V DC and a maximum power output of 60 watts, the IPOE-175 can power high-power PDs such as PTZ IP cameras, wireless access points, and VoIP phones. It also supports the latest IEEE 802.3bt PoE++ standard, providing up to 60 watts of power to compatible devices.
advertisement
Industrial IP67 1-Port 60W 802.3bt
PoE++ Injector
IPOE-175
User’s Manual
Table of Contents
2.1 Product Outlook ............................................................................. 4
2.2 Power Input Port ........................................................................... 4
2.3 Data Input Port and 802.3bt PoE++ Output Port .............................. 5
2.4 LED Indicators ............................................................................... 5
3.1 Installing Cable Gland with Power Cable and RJ45 UTP Cable ............ 6
3.2 Connecting Waterproof Cable Kit to the Outdoor PoE Injector ............ 6
3.3 Wall-mount Installation .................................................................. 9
3.4 Connecting IPOE-175 to PD ...........................................................10
3.5 Connecting IPOE-175 to PD ...........................................................10
1. Package Contents
Thank you for purchasing PLANET Industrial IP67 1-port 10/100/1000/2500T
802.3bt PoE++ Injector, IPOE-175. In the following sections, the term
“Outdoor PoE Injector” means the IPOE-175.
Open the box of the Industrial Ethernet Switch and carefully unpack it. The box should contain the following items:
IPOE-175 x 1 QR code sheet x 1 Wall-mounted Kit x 1
Spanner x 1
Power Cable with 2-pin
Terminal Block x 1
M22 Waterproof Cable
Gland x 3
Ground Wire x 1
If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.
Remarks: The color of the ground wire is different according to the batch, but its wire specifications meet the standard.
3
2. Hardware Introduction
This section describes the functionalities of the outdoor PoE Injector’s components.
2.1 Product Outlook
PoEin-Use
PWR IPOE-175
Figure 2-1: IPOE-175 product outlook
2.2 Power Input Port
Figure 2-2 shows the power input port side of the IPOE-175
Unit: mm
Figure 2-2: Power Input Port
4
2.3 Data Input Port and 802.3bt PoE++ Output Port
Figure 2-3 shows the data input port and PoE++ output port side of the IPOE-
175.
PoE++ Output Port Data Input Port
Figure 2-3: Two RJ45 Ports
2.4 LED Indicators
LED
PWR
PoE-in-Use
Color
Green
Amber
Function
Indicates it has power.
Indicates the port is providing power.
To install the 2-pin Terminal Block Connector on the Outdoor PoE Injector , simply follow the following steps:
Step 1: Insert positive DC power wire into V+ , negative DC power wire into
V, and grounding wire into Ground .
V
-
V+
2-pin
Step 2: Tighten the wire-clamp screws for preventing the wires from loosening and plug them into the Wall-mount Gigabit Ethernet Router
1. The wire gauge should be in the range from 20 to 22 AWG.
2. The device must be grounded.
5
3. Installation
This section describes how to install the Outdoor PoE Injector and make connections to it. Please read the following topics and perform the procedure in the order being presented.
3.1 Installing Cable Gland with Power Cable and RJ45 UTP
Cable
The cable gland consists of the following:
3.2 Connecting Waterproof Cable Kit to the Outdoor PoE
Injector
Step 1: Turn clockwise to tighten the gland body connected to the Outdoor
PoE Injector.
Step 2: Plug the power cable connector into the power input port.
6
Step 3: Insert the sealing insert into the cable gland body.
Step 4: Attach the clamping nut to the cable gland to complete the cable assembly.
Make sure the clamping nut is tightly attached to the cable gland body and the sealing insert is squeezed tightly.
7
Step 5: Repeat for “Data” Input Port and“PoE (Data + Power)”
Output Port.
8
1. Use only the waterproof cable gland provided in the package of the IPOE-175.
2. If the above installation procedure is not properly followed, the warranty will be invalidated.
3. If the waterproof cable gland is found missing or damage, please contact your local reseller where you purchased from.
40.78mm
5.00mm
11.31mm
14.00
13.72
20.18
4. Never use any waterproof cable gland that is not purchased from PLANET or doesn’t have the same dimensions of the
IPOE-175; it will damage the device permanently.
3.3 Wall-mount Installation
To install the Outdoor PoE Injector on the wall, please follow the instructions described below.
Step 1: Find the wall that you want to mount the Outdoor PoE Injector on.
Step 2: Refer to the picture below to screw the four screws on the wall
140.36mm
Step3: Use a screwdriver to screw them into the wall.
9
3.4 Connecting IPOE-175 to PD
Users MUST complete grounding wired with the device; otherwise, a sudden lightning could cause fatal damage to the device.
Earth Ground
EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.
3.5 Connecting IPOE-175 to PD
Step 1: Connect the additional Cat5e/6/6A cable from the PoE++ Out of the
IPOE-175 to a remote PD .
Ethernet Switch
Data
802.3bt PoE++
100m
PoE
Power Data PoE IP Camera
DC24-56V
DC
Power
IPOE-175
Power Supply
PoE
DC
1000BASE-T UTP
1000BASE-T UTP with PoE
Power Line (DC)
Step 2: The PoE++ Out port is the power injector which transmits DC voltage to the Cat5e/6/6A cable and transfer data from the Data source.
10
Step 3: Once the IPOE-175 detects the existence of an IEEE 802.3at/bt device or Ethernet device, the LAN LED indicator will be lit steadily, showing it is providing power.
According to IEEE 802.3at/bt standard, the IPOE-175 will not inject power to the cable if not connected to a standard IEEE
802.3at/bt device.
11
4. Product Specifications
Product
Hardware Specifications
Input Port
IPOE-175
Output Port
1 x 10/100/1000/2500BASE-T “Data” in RJ45 port
1 x 10/100/1000/2500BASE-T Ethernet with IEEE
802.3bt PoE++ “Data + DC” out RJ45 port
Interface
Data Rate
Input Power
Terminal
Block
1 x 2-pin terminal block
- Pin 1/2 for Power (Pin 1: V+ / Pin 2: V-)
LED Indicator
Input Voltage
10/100/1000/2500Mbps
PWR (Green)
PoE-in-Use x 1 (Amber)
24~56V DC
Power Consumption
ESD Protection
Surge Protection
Enclosure
Installation
Dimensions
(W x D x H)
Weight
MTBF
Network Cable
Voltage
DC 24V
DC 48V
DC 54V
System on
1.2W
1.44W
1.71W
Full Load (Max.)
72W
70.56W
65.8W
Air 8KV DC
Contact 6KV DC
6KV
IP67-rated and IK10 aluminum case
Wall-mount ear
150 x 43.8 x 72.94 mm
169.85 x 43.8 x 72.94 mm, with cable gland
485g
>100,000 hours
10BASE-T: UTP category 3, 5 cable (≤100m)
100BASE-TX: UTP category 5, 5e cable (≤100m)
1000BASE-T: UTP category 5e, 6 cable (≤100m)
2500BASE-T: UTP category 5e, 6, 6A cable (≤100m)
12
Power over Ethernet
PoE Standard
IEEE 802.3bt PoE++ type 3 PSE
Backward compatible with IEEE 802.3at PoE+
PoE Power
Supply Type
802.3btEnd-span/Mid-span
PoE Power
Output
55V DC
Max. 60 watts to 802.3bt PoE++ PD
Max. 30 watts to 802.3at PoE+ PD
Power Pin
Assignment
Stability Testing
802.3bt: 1/2 (-), 3/6 (+), 4/5 (+), 7/8 (-)
End-span: 1/2 (-), 3/6 (+)
Mid-span: 4/5 (+), 7/8 (-)
Standards Conformance
Regulatory
Compliance
FCC Part 15 Class A
CE
IEC 60068-2-32 (Free fall)
IEC 60068-2-27 (Shock)
IEC 60068-2-6 (Vibration)
Standard
Conformances
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3ab 1000BASE-T Gigabit Ethernet
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
IEEE 802.3bt Power over Ethernet Plus Plus
Environment
Operating
Temperature
Storage
Temperature
Humidity
-40 ~ 75 degrees C
-40 ~ 85 degrees C
5 ~ 95% (non-condensing)
The PoE power output ability will depend on the distance.
13
Customer Support
Thank you for purchasing PLANET products. You can browse our online FAQ resource and user’s manual on PLANET web site first to check if it could solve your issue. If you need more support information, please contact PLANET support team.
PLANET online FAQs: https://www.planet.com.tw/en/support/faq
Support team mail address: [email protected]
Copyright © PLANET Technology Corp. 2022.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
advertisement
Related manuals
advertisement
Table of contents
- 3 1. Package Contents
- 4 2. Hardware Introduction
- 4 2.1 Product Outlook
- 4 2.2 Power Input Port
- 5 2.3 Data Input Port and 802.3bt PoE++ Output Port
- 5 2.4 LED Indicators
- 6 3. Installation
- 6 3.1 Installing Cable Gland with Power Cable and RJ45 UTP Cable
- 6 3.2 Connecting Waterproof Cable Kit to the Outdoor PoE Injector
- 9 3.3 Wall-mount Installation
- 10 3.4 Connecting IPOE-175 to PD
- 10 3.5 Connecting IPOE-175 to PD
- 14 Customer Support