5-Ton Dual-Wedge Log Splitter
model number 060-3895-8
Please read and understand this manual before beginning any use or assembly of the product, and make sure all parts are present.
Questions?
If you have any questions or need replacement parts, please call our toll-free helpline at 1-866-523-5218.
Instruction
Manual
65558CA01M130_GB.indd 1
YW_060_3895_8_ElectricLogSplitter.indd
978343 CTC Generic AD8343 LITHO FLEXO
PANTONE
388
WO
Date
Artist w01a
PANTONE
3145
03
12/01/16 12/05/16 12/16/16 12/20/16
PA
02
PROCESS
BLACK mm/dd/yy w02a
PANTONE
COOL GRAY 11 mm/dd/yy
04 mm/dd/yy
05 mm/dd/yy w07a
12/29/16 02/08/17
Cindy Alexa
07 mm/dd/yy xxxxxx
2017/11/22 20:59:22
65558CA01M130_GB.indd 2 2017/11/22 20:59:22
STOP
ARRÊT
For problems or questions, DO NOT
RETURN TO STORE.
Please contact one of our Customer Service Agents who would be happy to assist you.
En cas de problèmes ou si vous avez des questions, NE RETOURNEZ PAS
L’ARTICLE AU MAGASIN.
Contactez plutôt un de nos agents du service à la clientèle, qui se fera un plaisir de vous aider.
For Customer Assistance Please Call:
Pour le service à la clientèle, veuillez composer:
CANADA: 1-866-523-5218
65558CA01M130_GB.indd 3 2017/11/22 20:59:22
4 model no. 060-3895-8 | contact us 1.866.523.5218
Specifications
Important Safety Instructions
Symbols
Parts List
Exploded View
Parts Location
Important Information
Before Assembly
Assembly
Operation
Maintenance
Storage
Troubleshooting
Environmental Protection
Warranty
25
26
27
27
15
17
18
23
9
12
13
14
5
6
8 model no. 060-3895-8 | contact us 1.866.523.5218
65558CA01M130_GB.indd 4 2017/11/22 20:59:22
model no. 060-3895-8 | contact us 1.866.523.5218
model no. 060-3895-8 | contact us 1.866.523.5218
Product Name
Model Number
Motor
Log Capacity
(Diameter)
Log Capacity (Length)
Splitting Force
Hydraulic Pressure
Hydraulic Oil Capacity
5-Ton Dual-Wedge Log Splitter
060-3895-8
120 V 60 Hz 15 A 1 3/4 HP
10" (25 cm) (single wedge)
10" (25 cm) (dual wedge)
20 1/2" (52 cm) (single wedge)
17 11/32" (44 cm) (dual wedge)
5 Tons
20 MPa
3.2 L
DIMENSIONS
Length
Width
Height
Product Weight
37" (94 cm)
10 1/2" (27 cm)
20" (51 cm)
103 lb (46.8 kg)
5
65558CA01M130_GB.indd 5
NOTE: The log capacity in diameter is only a guideline. A small log can be difficult to split if it has knots or very tough fibre.
2017/11/22 20:59:22
6 model no. 060-3895-8 | contact us 1.866.523.5218
IMPORTANT! READ AND UNDERSTAND
ALL INSTRUCTIONS.
Failure to follow safety instructions may result in electric shock, fire, and/or serious personal injury.
• Read and understand all instructions and all labels affixed to the log splitter. Learn the applications, limitations, and specific potential hazards before using this log splitter.
PERSONAL SAFETY
• Do not operate the log splitter while under the influence of drugs, alcohol, or any medication.
• Stay alert, watch what you are doing, and use common sense. Do not operate the log splitter when you are tired.
• Dress properly. Do not wear loose clothing, neckties, or jewellery that can get caught and draw you into moving parts. Rubber gloves and non-skid, steel-toed footwear should be worn when working with the log splitter. Wear protective hair covering to contain long hair and prevent it from getting caught in the log splitter.
• Always wear safety goggles. The use of a log splitter can result in foreign objects being thrown into your eyes which can result in severe or permanent eye damage. Everyday eyeglasses only have impact-resistant lenses; they are not safety glasses.
• Never stand on the log splitter. Never allow anyone to ride on the machine. Do not transport anything or anyone on the log splitter. Serious injury could occur if the machine is tipped or jarred.
• Do not remove jammed logs using your hand.
• Keep hands away from moving parts. Do not place your hands in splits and cracks that open in the log. They may close suddenly which could cause severe crushing or amputation.
• Keep your hands away from the controls while logs are being loaded and unloaded.
Ensure that the loader and the operator are positioned in the safe area at the control end of the log splitter while the log pusher is moving.
ELECTRICAL SAFETY
• Always unplug the log splitter from the power supply when it is not in use, and before making adjustments, changing parts, cleaning, or servicing the log splitter.
• If an extension cord is needed, make sure to use a proper extension cord. The cord should be no longer than 32.5’ (10 m) with a cross-section of no less than 1/8” (2.5 mm) and a wire size (A.W.G.) of 12 in order to allow sufficient flow of electric current to the motor. An undersized cord may result in loss of power and overheating.
• Electrical connections must be made with protected material suitable for outdoor use. Avoid using loose and inadequately insulated connections.
• Only use an electrical circuit having adequate protection and capacity corresponding to the power, voltage, and frequency of the log splitter. Ensure that there is a ground connection and a regulation differential switch upstream.
• Ground the log splitter. This log splitter is equipped with an electric cord having an equipment-grounding conductor and a grounding pin. Insert the plug to a matching electrical outlet. Do not modify the plug or remove the grounding pin.
• Do not touch the metal prongs of the electric cord plug when inserting or removing the plug from an electrical outlet. Prevent body contact with grounded surfaces such as pipes, radiators, rangers, and refrigerators.
• Never open the pushbutton box. Contact a qualified electrician if it is necessary to open this box.
WORK AREA SAFETY
• Place the log splitter on a flat, stable, and level surface that is 24–30” (60–75 cm) high.
Operate the log splitter in a location where there is plenty of room for handling.
• To prevent unintended movement during operation, anchor the log splitter to the work area if it tends to slip, move, or slide.
• Keep the work area clean. A cluttered workplace invites accidents. Do not leave tools or pieces of wood on the log splitter during operation.
• Before beginning any work using the log splitter, make sure the work area has sufficient lighting and that no obstructions will interfere with the safety of operation.
model no. 060-3895-8 | contact us 1.866.523.5218
65558CA01M130_GB.indd 6 2017/11/22 20:59:22
model no. 060-3895-8 | contact us 1.866.523.5218
model no. 060-3895-8 | contact us 1.866.523.5218
• Do not operate the log splitter in dangerous environments. Do not use the log splitter in wet or damp conditions, and do not expose it to rain. In order to avoid potential fire hazards, never use the log splitter in an explosive atmosphere where there are fumes from paint, solvents, and other flammable liquids.
• Keep children and visitors away. Never allow children or untrained adults to operate the log splitter.
• Make the workshop childproof. Disconnect the power cord. Store the log splitter away from children and other individuals not qualified to use it. Keep the workshop locked.
SAFE OPERATION
• Always check the oil level before using the log splitter.
• Keep all guards in place and in working order.
• Always inspect the log splitter before turning it on. Make it a habit to check the log splitter for oil leaks around the ram cylinder. Do not operate the log splitter if oil is leaking. Refer to the Troubleshooting section in this manual.
• Check for damaged parts. Inspect the log splitter, including the splitting wedge and guards, for any malfunctioning or damaged components, cracks, and deformation.
Replace damaged, missing, or faulty parts before using the log splitter.
• Check for alignment of moving parts, binding of moving parts, mounting and any other conditions that may affect the operation of the log splitter.
• Do not place the log splitter on the ground during operation. Doing so creates an awkward operating position in which the operator’s face is close to the machine thus increasing the risk of being struck by wood chips or debris.
• The log splitter must always be operated by only one person. If another person is helping to load logs to be split, do not start the machine until that person is clear of the operating zone. Never ask another person for help in freeing a jammed log.
• Inspect the log before loading it on the log splitter. Ensure there are no nails or foreign objects in the logs to be split. The logs should be cut as squarely as possible.
Branches must be cut off flush with the trunk.
• Always pay attention to the movement of the log pusher. Do not load a log until the log pusher has stopped. Do not attempt to remove split logs until the machine has totally completed its work cycle and has stopped.
• Never attempt to split more than one log at a time.
• Do not force the log splitter. It will do the job better and safer at the feed rate for which it was designed.
• Do not attempt to split logs that are larger than the log capacity indicated in the Specifications section. Doing so is dangerous and may damage the machine.
• Only use the log splitter for its intended purpose. Do not force the machine to do a job for which it was not designed.
• Never leave the log splitter unattended while it is running. Turn the power off. Do not leave the machine until it comes to a complete stop.
• Consult the instruction manual before servicing. Product repairs and service must be performed only by qualified repair personnel.
• Maintain the log splitter with care. Keep the log splitter clean and the blade sharp for better and safer performance. Follow instructions for lubricating and changing accessories.
• Do not dump used oil into drains, soil, or water. Dispose of used oil only at an authorized collection point, or follow the regulations that are in effect in your area.
• Only use the parts and accessories supplied with this product or specifically designated for use with this product by the manufacturer. Using other parts and accessories not designated by the manufacturer could result in personal injury or property damage.
SAVE THESE INSTRUCTIONS.
7
65558CA01M130_GB.indd 7 2017/11/22 20:59:22
8 model no. 060-3895-8 | contact us 1.866.523.5218
Symbol Name Designation/Explanation
Read the instruction manual.
Inspect the log splitter.
Dress properly.
Protect your eyes and face.
Keep visitors and children away.
User must read and understand the instruction manual and all labels affixed to the product before using this product.
Inspect the log splitter for any malfunctioning or damaged components.
Do not wear loose clothing, gloves, neckties, or jewellery (rings, wrist watches), because they can get caught in moving parts. Wear nonconductive protective gloves and non-skid, steel-toed footwear. Wear protective hair covering to contain long hair.
Always wear safety goggles.
Everyday eyeglasses only have impact-resistant lenses. They are not safety glasses.
Always keep other people a safe distance away from the work area, especially when the log splitter is in use. The log splitter must always be operated by only one person.
Symbol Name
Avoid injury from unexpected accidents.
Protect your hands.
Disconnect the power.
Protect the environment.
Warning
Caution
Note
Designation/Explanation
Always pay attention to the movement of the log pusher. Keep hands and body out of the way of all moving parts.
Keep your hands away from splits and cracks that open in the log. Do not remove jammed logs using your hands. Keep hands off the controls while logs are being loaded and unloaded.
Unplug the log splitter when it is not in use and before making adjustments, changing parts, cleaning, or servicing.
Dispose of used oil only at an authorized collection point, or follow the regulations that are in effect in the area where the log splitter is used.
Indicates a potentially hazardous situation, which, if not avoided could result in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
Notes and reminders for the operator.
model no. 060-3895-8 | contact us 1.866.523.5218
65558CA01M130_GB.indd 8 2017/11/22 20:59:23
model no. 060-3895-8 | contact us 1.866.523.5218
9 model no. 060-3895-8 | contact us 1.866.523.5218
37
38
39
40
32
34
35
36
28
29
30
31
24
25
26
27
20
21
22
23
12
13
18
19
8
9
10
11
4
5
6
7
Item
1
2
3
Description
Lever Mount Nut
Nut Cap M10
Lever
Lever Knob
Guard Plate
Nut
Copper gasket
Screw M8
O-Ring 5.5 x 2
Snap Washer – Shaft
Valve Retract Spring
O-Ring 6.7 x 1.8
Valve Core Rod
Aluminum Cover (Rear)
O-Ring 55 x 3.1
Piston
Piston ring
O-Ring 32 x 3.5
Spring
Stud
Hydraulic Cylinder
Aluminum Cover (Front)
Piston Rod Seal
O-Ring 7 x 1.9
Bleed Screw
Flat Washer Groupware M14
Dipstick
Piston Rod
Screw M6 x 16
Frame Tube
Lead Plank
Spring Washer M6
Screw M6x10
Nut M14
Flat Washer
65558CA01M130_GB.indd 9
2
2
4
6
1
2
1
2
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
2
4
1
1
Qty
1
3
1
2017/11/22 20:59:23
10 model no. 060-3895-8 | contact us 1.866.523.5218
70
71
72
73
74
75
66
67
68
69
62
63
64
65
58
59
60
61
54
55
56
57
50
51
52
53
46
47
48
49
Item
41
42
43
44
45
Description
Nut
Nut plug
Flat Washer Groupware M18
Valve Sleeve
O-Ring 12.5 x 1.8
Adjusting Screw
Steel Ball
Pressure Limited Valve Spring
Adjusting Screw
Log Pusher Connection Weldment
Plastic Insert 1
Plastic Insert 2
Log Pusher
Nut M10
Flat Washer
Screw M10 x 25
Wheel Cover
Block Turn
Wheel
Washer
Wheel Shelf
Bolt
Spring Washer
Washer
Gear Pump Cover
O-Ring 10.6 x 2.65
Gear Housing Plate
C-Clip
Gear Shaft
Steel Ball
Gear
Pin
Washer
Bolt
Motor Cover
65558CA01M130_GB.indd 10
1
6
1
2
3
1
2
1
2
1
9
1
6
9
4
1
2
2
4
2
4
5
1
1
1
1
1
1
1
1
Qty
1
1
2
1
5
2017/11/22 20:59:23 model no. 060-3895-8 | contact us 1.866.523.5218
model no. 060-3895-8 | contact us 1.866.523.5218
model no. 060-3895-8 | contact us 1.866.523.5218
106
107
108
110
111
98
99
100
101
102
103
104
105
94
95
96
97
88
89
91
93
84
85
86
87
80
81
82
83
Item
76
77
78
79
Description
Seal
Nut
Screw
Motor
Fan
Block Turn
Shroud
Spring Washer
Screw
Leg
Washer
Bolt
Leg Cover
Cable & Plug
Cord Stop
Screw
Switch Box Cover
Airproof Underlay
Connection Terminal
Capacitor
Switch
Switch Box
Waterproof Underlay
Left Motor Support Shoe
Right Motor Support Shoe
Pin
Spring
Sliding Sleeve
Bolt
Fuse
Manual
Retaining Valve
Duo-Cut Blade
1
1
3
1
1
2
4
1
2
1
1
1
1
1
1
1
1
1
1
1
11
2
2
3
1
1
3
1
1
Qty
1
1
1
1
11
65558CA01M130_GB.indd 11 2017/11/22 20:59:23
12 model no. 060-3895-8 | contact us 1.866.523.5218
model no. 060-3895-8 | contact us 1.866.523.5218
65558CA01M130_GB.indd 12 2017/11/22 20:59:23
model no. 060-3895-8 | contact us 1.866.523.5218
model no. 060-3895-8 | contact us 1.866.523.5218
11
12
13
14
15
7
8
9
10
5
6
3
4
Item
1
2
9
11
10
Description
Log pusher
Work table
Wedge
Support leg
Log retaining plates
Motor
Pushbutton box
Pushbutton switch
Wheels (for minor moving only)
Hydraulic control lever
Control lever guard
Bleed screw
Oil drain bolt with dipstick
Maximum pressure limiting screw
Dual wedge wedge
1
2 3
8 7 6 5 4
15
10
14
13
12
13
65558CA01M130_GB.indd 13 2017/11/22 20:59:23
14 model no. 060-3895-8 | contact us 1.866.523.5218
NOTE: The safe use of this product requires an understanding of the information on the product and this operator’s manual as well as knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features and safety rules.
1. INTENDED USE
This log splitter is intended for household use only. Do not use this log splitter for industrial or other commercial application. Do not use the log splitter for processing any material other than wood.
2. OPERATING FEATURES
2.1 BLEED SCREW
The bleed screw allows air to flow in and out of the oil tank.
WARNING! Failure to loosen the bleed screw may cause the seals in the hydraulic system to rupture and cause serious physical injuries and/ or permanent damage to the log splitter. Make sure to loosen the bleed screw prior to operating the log splitter.
2.2 MAXIMUM PRESSURE LIMITING SCREW
The maximum pressure was set at 5 tons in the factory. The limiting screw is sealed with glue to ensure this setting will not change and the log splitter does not operate in splitting pressures less than or exceeding 5 tons. The pressure was set by a qualified mechanic using professional instruments.
WARNING! Do not adjust the maximum pressure limiting screw.
Unauthorized resetting may cause the hydraulic pump to weaken its splitting pressure or it may result in serious personal injury and/or damage to the log splitter.
2.3 DUAL WEDGE WEDGE
The Dual wedge wedge allows twice the effective splitting capacity of other similarly rated electric log splitters
3. SAFETY FEATURES
3.1 ZHB CONTROL SYSTEM
This log splitter is equipped with a ZHB control system which means that the operator must use both hands. The left hand controls the hydraulic lever, while the right hand controls the pushbutton switch. If one hand lets go of either the switch or the lever, the log splitter stops immediately.
65558CA01M130_GB.indd 14 2017/11/22 20:59:23
model no. 060-3895-8 | contact us 1.866.523.5218
model no. 060-3895-8 | contact us 1.866.523.5218
TOOLS NEEDED FOR ASSEMBLY (NOT SUPPLIED):
#6 Hex wrench
7/16 Box end wrench
UNPACKING INSTRUCTIONS
This log splitter is shipped completely assembled with the exception of installing the wheels.
• Carefully remove the log splitter and its accessories from the box.
• Check and make sure all parts and accessories are included before using the log splitter for the first time. Refer to the Parts Location section.
• Inspect the log splitter and its accessories for any damage.
• If there is any damage or missing parts and/or accessories, contact the customer service helpline at 1-866-523-5218 before using the log splitter.
CHOOSING A LOCATION
• Choose a location where there is plenty of room for handling. Carefully lift the log splitter from both ends and place the log splitter on a stable, flat, and level work surface that is
24–30" (60–75 cm) high.
15
24-30” (60-75 cm)
NOTE: This log splitter is designed to operate in ambient temperatures between -20° and 40° C (-4° and 104° F). It can be stored or transported in ambient temperatures between -25° and 55° C (-13° and 131° F).
65558CA01M130_GB.indd 15 2017/11/22 20:59:23
16 model no. 060-3895-8 | contact us 1.866.523.5218
ELECTRICAL REQUIREMENTS
• Use a standard 120 V (±10%) 60 Hz (±1 Hz) AC only electrical supply that has undervoltage, over-voltage, and over-current protection devices as well as a residual current device (RCD) with a maximum residual current rated at 0.03 A for the log splitter.
Wiring diagram
L N
Plumbing diagram
KH
SB
M
M
PE
C
WARNING! To reduce the risk of electric shock, this equipment has a grounding type plug that has a third (grounding) pin. This plug will only fit into a grounding type outlet. If the plug does not fit into the outlet, please contact a qualified electrician to install the proper outlet.
Do not modify the plug or remove the grounding pin.
• If an extension cord is needed, use only a 3-wire extension cord that has a 3-prong grounded plug. The cord must be plugged into a matching outlet that has 3 poles in the receptacle.
The extension cord must be no longer than
32.5' (10 m), have a cross-section of no less than 1/8" (2.5 mm), and a wire size (A.W.G.) of
12. When working with the log splitter outdoors, use only extension cords that are clearly marked for outdoor use.
120V
WARNING! Keep the extension cord clear of the working area. Route the cord away from foot traffic so that it will not be tripped over or get caught in lumber, tools, or other obstructions. Failure to do so can result in serious physical injuries.
WARNING! Always check all cords before each use. Never use a damaged cord in order to avoid electrical shock resulting in serious injury. Replace damaged cords before operating the log splitter.
65558CA01M130_GB.indd 16 2017/11/22 20:59:23 model no. 060-3895-8 | contact us 1.866.523.5218
model no. 060-3895-8 | contact us 1.866.523.5218
model no. 060-3895-8 | contact us 1.866.523.5218
CAUTION! To avoid possible electric shock, switch off the power supply at the main fuse or circuit breaker box before assembling, servicing, or cleaning the log splitter.
1. ASSEMBLING THE WHEELS
• Install the wheel onto the axle with the front side of the wheel facing outward.
• Push the hitch pin through the hole in the axle until it locks.
• Place the wheel cover in the centre where the axle protrudes from the wheel and push to lock the wheel cover in place.
CAUTION! Check and make sure that the log splitter is disconnected from the power supply before installing the Dual wedge wedge.
2. INSTALLING THE DUAL WEDGE WEDGE
• Remove the 4 sets of bolts and nuts from the log pusher using a #6 Hex wrench for the bolts and a 7/16 box end wrench for the nuts. Set aside for later use.
• Remove the log pusher.
• Place the Dual wedge wedge in the welded log pusher connection.
• Align the holes of the wedge to the holes on the connection.
• Insert all the previously removed bolts and nuts into the holes.
• Ensure that the wedge is in correct position and then proceed to tighten all bolts and nuts using the wrenches.
Log Pusher
Duo-cut Splitting Wedge
17
65558CA01M130_GB.indd 17 2017/11/22 20:59:24
18 model no. 060-3895-8 | contact us 1.866.523.5218
CAUTION!
• Before using the log splitter, make sure that the work area is clear of obstructions, clutter, children, and pets. Work only in an area with ample lighting.
• Dress properly. Wear rubber gloves and non-skid, steel-toed footwear.
• When splitting logs, wear safety goggles to protect against eye injury.
1. CHECK THE OIL
• Ensure the log splitter is disconnected from the power supply.
• Using the support leg handle, stand the log splitter on the end with the wheels.
• Loosen the oil drain bolt and remove from the oil tank to see the attached oil dipstick.
• Wipe the dipstick clean and then re-insert it back into the oil tank. Pull up the dipstick and check if the oil level is between the
2 grooves on the dipstick.
Oil level
• If there is not enough oil in the tank, refer to “Replacing the Hydraulic Oil” in the
Maintenance section.
• After verifying that the oil level is correct, insert the bolt with dipstick back into the oil tank. Tighten the drain bolt in order to avoid leakage, and then place the log splitter back to its normal horizontal position.
Oil drain bolt with dipstick model no. 060-3895-8 | contact us 1.866.523.5218
65558CA01M130_GB.indd 18
NOTE: Also check for oil leaks around the ram cylinder and other points. Refer to the Troubleshooting section if there are oil leaks.
2017/11/22 20:59:24
model no. 060-3895-8 | contact us 1.866.523.5218
model no. 060-3895-8 | contact us 1.866.523.5218
Bleed screw
2. LOOSEN THE BLEED SCREW
• Turn the bleed screw 3 full turns.
• Leave the bleed screw in a vertical position aligned behind the wedge or in a horizontal position aligned with the work table in order to avoid being sheared off by the split log during operation.
WARNING! Always loosen the bleed screw before operating the log splitter. Failure to loosen the bleed screw may cause the seals in the hydraulic system to rupture and cause serious physical injuries and/or permanent damage to the log splitter.
3. USING THE LOG SPLITTER a. Plug the power cord of the log splitter into the power supply.
b. Load the log into the log splitter by placing the log lengthwise, lying flat on the work table within the log retaining plates, and in the direction of the grain (fig. 1).
1
19
WARNING! After 5 seconds of activation and the wood is not moving, the pressurized oil becomes overheated and could damage the motor.
Never keep pressure on the wood by trying to force the log splitter for more than 5 seconds. If the log is extremely hard, rotate the log 90° in order to split it from the other side. If this doesn’t work, it means that the hardness of the log exceeds the capacity of the log splitter therefore, the log should be discarded. Do not force the log splitter to split very hard wood.
65558CA01M130_GB.indd 19 2017/11/22 20:59:24
20 model no. 060-3895-8 | contact us 1.866.523.5218
WARNING!
• Do not place the log at an angle against the wedge to split the log on the upper part (fig. 2).
Doing so can break the wedge or damage the machine.
• Do not place the log crosswise on the splitter (fig. 3). This is dangerous and may seriously damage the machine.
• Do not split more than one log at a time. One of them may fly out the splitter and cause injury.
• If the log is small, place it against the log pusher before starting the splitter.
• Do not try to split logs that are larger than the log capacity indicated in the Specifications section.
2
3 model no. 060-3895-8 | contact us 1.866.523.5218
4 c. The operator must be positioned at the control end of the log splitter behind the wheels as shown in figure 4.
65558CA01M130_GB.indd 20 2017/11/22 20:59:25
model no. 060-3895-8 | contact us 1.866.523.5218
model no. 060-3895-8 | contact us 1.866.523.5218
WARNING! Do not crouch on the ground, sit down on a log beside the splitter, or kneel down by the log splitter (fig. 5). Always keep your hands and body out of the splitting or operating zone while using the log splitter.
5
21 d. Using your right hand, push and hold down the pushbutton switch (fig. 6).
e. While holding down the switch with your right hand, use your left hand to push the hydraulic control lever down (fig. 6).
6
NOTE: Both hands are required to start the log splitter.
Simultaneously holding the switch with your right hand and pushing the hydraulic control lever down with your left hand starts the hydraulic pump which pushes the log into the wedge.
If either hand is removed from either one of the controls, the log splitter will automatically return to the starting position.
WARNING! After 5 seconds, the pressurized oil becomes overheated and could damage the motor. Never keep pressure on the wood by trying to force the log splitter for more than 5 seconds. If the log is extremely hard, rotate the log 90° and try to split it in a different direction. If this doesn’t work, it means that the hardness of the log exceeds the capacity of the log splitter therefore, the log should be discarded. Do not force the log splitter to split very hard wood.
65558CA01M130_GB.indd 21 2017/11/22 20:59:26
22 model no. 060-3895-8 | contact us 1.866.523.5218
7 f. Stop the log splitter by simultaneously releasing the hydraulic control lever and the switch (fig. 7). Wait for the log pusher to return to its starting position. g. Repeat steps b through f for the other logs.
h. When the splitting of all logs is complete or if the machine will be unattended for any period of time, unplug the cord from the power supply (fig. 8).
i. To avoid oil leakage, tighten the bleed screw when moving the log splitter or when the log splitter is no longer in use.
8
120V
4. FREEING A JAMMED LOG
• Release both the switch and the hydraulic control lever.
• After the log pusher moves back to its starting position and comes to a complete stop, insert a piece of wood or wood wedge that fits on the splitter behind or under the jammed log (fig. 9).
• Simultaneously hold down the switch using your right hand and push the hydraulic control lever down using your left hand to start the log splitter. The piece of wood will move forward freeing the jammed log.
• If the log is not freed, repeat this procedure with a steeper sloped piece of wood until the log is free.
9
120V
WARNING! Do not try to knock the jammed log off the log splitter
(fig. 10). Doing so will damage the machine or cause the log to fly out of the splitter which could result in an injury.
10 model no. 060-3895-8 | contact us 1.866.523.5218
65558CA01M130_GB.indd 22 2017/11/22 20:59:26
model no. 060-3895-8 | contact us 1.866.523.5218
model no. 060-3895-8 | contact us 1.866.523.5218
WARNING! To avoid possible electric shock, always disconnect the log splitter from the power supply and tighten the bleed screw before cleaning, making adjustments, or conducting maintenance work on the log splitter.
REPLACING THE HYDRAULIC OIL
Replace the hydraulic oil in the log splitter after every 150 hours of use.
When replacing the hydraulic oil, it is recommended to use one of the following:
• 10W AW32
• ASLE H-150
• ISO 32
11
• Check and make sure that all moving parts have come to a complete stop.
• Turn off the log splitter and unplug it from the power supply.
• Using the support leg handle, stand the log splitter on the end with the wheels.
• Unscrew the oil drain bolt with dipstick and remove it.
• Tilt the log splitter onto the support leg over a 4-liter container in order to drain the hydraulic oil (fig. 11).
23
• Using the support leg, tilt the log splitter back onto the motor side.
• Using a funnel (not provided), refill the oil tank with the proper volume of fresh hydraulic oil (fig. 12).
12
3.2 L
HYDRAULIC
OIL
65558CA01M130_GB.indd 23 2017/11/22 20:59:27
24 model no. 060-3895-8 | contact us 1.866.523.5218
• Wipe the dipstick clean and insert it back into the oil tank to check for the oil level.
• Remove the dipstick and check for oil level. The level of the refilled oil should be between the 2 grooves of the dipstick. If not, add or decrease the amount of oil in the tank until the level is between the 2 grooves of the dipstick.
Oil level
• After verifying that the oil level is correct, insert the bolt with dipstick back into the oil tank. Tighten the drain bolt in order to avoid leakage, and then place the log splitter back to its normal horizontal position.
Oil drain bolt with dipstick model no. 060-3895-8 | contact us 1.866.523.5218
Note:
• Check the oil level regularly and before starting the log splitter. Ensure that the oil level is between the 2 grooves on the dipstick. When the oil level is below the lower groove, refill the oil tank before operating the log splitter.
• Dispose of used oil only at an authorized collection point, or follow the regulations that are in effect in your area.
65558CA01M130_GB.indd 24 2017/11/22 20:59:27
model no. 060-3895-8 | contact us 1.866.523.5218
model no. 060-3895-8 | contact us 1.866.523.5218
SHARPENING THE BLADE
After using the log splitter for some time, sharpen the blade or wedge using a fine-toothed file. Smooth out any burns or crushed areas along the cutting edge.
CLEANING
• Use a clean cloth to remove dirt, dust, oil, and grease. Use a soft brush on the splitting area and the motor ventilation area to remove any wood debris.
• DO NOT immerse the log splitter in water or other cleaning agents.
25
STORAGE
• Turn off the motor and unplug the log splitter from the power supply.
• Close the bleed screw to prevent oil leakage and clean any debris from the log splitter before storing.
• Store the log splitter in a cool, dry location that is not accessible to children and other unauthorized persons. Secure the log splitter and make sure it cannot fall over and cause damage or injury.
65558CA01M130_GB.indd 25 2017/11/22 20:59:27
26 model no. 060-3895-8 | contact us 1.866.523.5218
Problem
The log splitter does not split logs.
Possible Reason
The log is not positioned correctly.
The size or hardness of the log exceeds the capacity of the machine.
The wedge cutting edge is blunt.
There is an oil leak.
Solution
Refer to the Operation section for instructions on proper log loading.
Reduce the size of the log before splitting it on the log splitter.
Refer to “Sharpening the blade” under the Maintenance section for instructions on how to sharpen the cutting edge.
Locate the leak, and call the helpline.
An unauthorized adjustment was made to the maximum pressure limiting screw—a lower maximum pressure was set.
Call the helpline.
The log pusher moves jerkily, makes an unfamiliar noise, or vibrates excessively.
Not enough hydraulic oil and too much air in the hydraulic system.
Oil leaks around the ram cylinder or from other points.
Check the oil level, and refill the oil if necessary. If the problem persists, call the helpline.
Air was sealed in the hydraulic system during operation.
Loosen the bleed screw by
3 or 4 rotations before operating the log splitter.
The bleed screw was not tightened before moving the log splitter.
Tighten the bleed screw before moving the log splitter.
The hydraulic control valve assembly and/or seal are worn.
Call the helpline.
model no. 060-3895-8 | contact us 1.866.523.5218
65558CA01M130_GB.indd 26 2017/11/22 20:59:27
model no. 060-3895-8 | contact us 1.866.523.5218
Problem
The log splitter does not split logs.
Possible Reason
The log is not positioned correctly.
The size or hardness of the log exceeds the capacity of the machine.
The wedge cutting edge is blunt.
There is an oil leak.
Solution
Refer to the Operation section for instructions on proper log loading.
Reduce the size of the log before splitting it on the log splitter.
Refer to “Sharpening the blade” under the Maintenance section for instructions on how to sharpen the cutting edge.
Locate the leak, and call the helpline.
An unauthorized adjustment was made to the maximum pressure limiting screw—a lower maximum pressure was set.
Call the helpline.
The log pusher moves jerkily, makes an unfamiliar noise, or vibrates excessively.
Not enough hydraulic oil and too much air in the hydraulic system.
Oil leaks around the ram cylinder or from other points.
Check the oil level, and refill the oil if necessary. If the problem persists, call the helpline.
Air was sealed in the hydraulic system during operation.
Loosen the bleed screw by
3 or 4 rotations before operating the log splitter.
The bleed screw was not tightened before moving the log splitter.
Tighten the bleed screw before moving the log splitter.
The hydraulic control valve assembly and/or seal are worn.
Call the helpline.
model no. 060-3895-8 | contact us 1.866.523.5218
Used electrical products are recyclable and should not be discarded in your regular domestic waste. Please actively support us in conserving resources and protecting the environment by returning this appliance to a collection centre (if available).
Do not dump used oil into drains, soil, or water. Dispose of used oil only at an authorized collection point or follow the regulations that are in effect in your area.
WARRANTY
For TWO YEARS from the date of purchase within Canada, YARDWORKS CANADA will, at its option, repair or replace for the original purchaser, free or charge, any part or parts found to be defective in material or workmanship.
This warranty does not cover:
1. Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident, improper maintenance, or alteration; or
2. The unit, if it has not been operated and/or maintained in accordance with the owner’s manual; or
3. Normal wear, except as noted below;
4. Routine maintenance items such as lubricants, blade sharpening;
5. Normal deterioration of the exterior finish due to use or exposure.
Full One Hundred Twenty Days Warranty on Normal Wear Parts: Normal wear parts are defined as blade adaptors, blades, grass bags and tires. These parts are warranted to the original purchaser to be free from defects in material and workmanship for a period of one hundred twenty (120) days from the date of retail purchase.
How to Obtain Service: Warranty service is available by calling the toll-free helpline, at
1 866-523-5218. The factory will not accept the return of a complete unit unless prior written permission has been extended by YARDWORKS CANADA .
Transportation Charges: Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. The purchaser must pay transportation charges for any part submitted for replacement under this warranty unless such return is requested in writing by YARDWORKS CANADA .
Other Warranties: All other warranties, express or implied, including any implied warranty of merchantability is limited in its duration to that set forth in this express limited warranty. The provisions as set forth in this warranty provide the sole and exclusive remedy of YARDWORKS
CANADA obligations arising from the sale of its products.
YARDWORKS CANADA will not be liable for incidental or consequential loss or damage.
27
65558CA01M130_GB.indd 27 2017/11/22 20:59:27
Imported by YardWorks Canada
Toronto, Canada M4S 2B8
65558CA01M130_GB.indd 28 2017/11/22 20:59:27
