DeVilbiss DV1 S HVLP KIT (1.0,1.2, DV1-S2, CUPPED) 704533 Service Manual

SERVICE MANUAL

EN

DV1 S Gravity Spray Gun

II 2 G X / Ex h II Gb X

IMPORTANT! DO NOT DESTROY

It is the Customer's responsibility to have all operators and service personnel read and understand this manual.

Contact your local Carlisle Fluid Technologies representative for additional copies of this manual.

READ ALL INSTRUCTIONS BEFORE OPERATING THIS PRODUCT.

SB-E-2-984 R1.0 (03/2021) www.carlisleft.com

EN

FUNCTIONAL DESCRIPTION

The DV1 S spray gun is a professional quality spray gun designed to comply with all global legislations.

SPECIFICATIONS

AIR INLET PRESSURES

P1 = Max. Static Air Input Pressure 12 bar [175 psi]

Gun Air Inlet Pressure with gun triggered

See Table 1

Page 8

Vibration Level: <2.5 m/s²

Sound Power Level: Available On Request

Sound Pressure Level: Available On Request

ENVIRONMENTAL

Max. Ambient Operating Temperature 40°C Nominal [104°F]

MATERIALS OF CONSTRUCTION

Gun Body Material Anodised Aluminum

Fluid Nozzle, Fluid Needle and Trigger Stud Stainless Steel

Air Cap Material Electroless Nickel Plated Brass

Retaining Ring, Sprayhead, Adjusting Knobs, Air Valve

Cage, Sleeve

Anodised Aluminum

Springs, Clips, Screws Stainless Steel

Seals and O-Rings Solvent Resistant

Trigger Chrome Plated Steel

Valve Bodies, Rear Housing, Packing Nut, Sleeve Nut Chrome Plated Brass

Air Valve Stem Electroless Nickel Plated Brass

CONNECTIONS

Air Inlet Size 1/4'' Universal

Fluid Inlet Size 7/16" - 14 UNC

WEIGHT

GUN ONLY 340g [12.0 oz]

DIMENSIONS

L x H x W mm [inches] 139 x 160 x 35.6 [5.5 x 6.3 x 1.4 in]

SB-E-2-984 R1.0

2/24

www.carlisleft.com

Product Description / Object of Declaration: DV1 S

This Product is designed for use with:

Suitable for use in hazardous area:

Protection Level:

Solvent and waterborne materials

Zone 1 / Zone 2

II 2 G X/Ex h II Gb X

Notified body details and role:

This Declaration of conformity / incorporation is issued under the sole responsiblity of the manufacturer:

Element Materials Technology (0891)

Lodging of Technical file

Carlisle Fluid Technologies UK Ltd,

Ringwood Road,

Bournemouth, BH11 9LH. UK

EU Declaration of Conformity

The object of the declaration described above is in conformity with the relevant Union harmonisation legislation:

ATEX Directive 2014/34/EU

Machinery Directive 2006/42/EC

By complying with the following statutory documents and harmonised standards:

EN 1127-1:2011 Explosive atmospheres - Explosion prevention - Basic concepts

BS EN 1953:2013 Atomizing and spraying equipment for coating materials - Safety requirements

EN ISO 12100:2010 Safety of Machinery - General Principles for Design

EN ISO 80079-36:2016 Explosive Atmospheres- Part 36:Non Electrical equipment for explosive atmospheres-

Basic methods and requirements.

EN ISO 80079-37:2016 Explosive Atmospheres- Part 37: Non Electrical equipment for explosive atmospheres - protection by methods "c", "b" and "k".

HVLP and High Efficiency products comply with the requirements of PG6 from the EPA guidelines and offer greater than 65% transfer efficiency.

High volume, low pressure (HVLP) sprayguns are designed to reduce overspray and provide maximum transfer efficiency by limiting air cap pressure to 0.69 bar (10 psi) (complies with rules issued by SCAQMD and other authorities).

Providing all conditions of safe use / installation stated within the product manuals have been complied with and also installed in accordance with any applicable local codes of practice.

Vice President of Engineering

Signed for and on behalf of Carlisle Fluid

Technologies UK Ltd:

SB-E-2-984 R1.0

3/24

M.Munoz

31/3/21 www.carlisleft.com

Product Description / Object of Declaration: DV1 S

This Product is designed for use with:

Suitable for use in hazardous area:

Protection Level:

Solvent and water based materials

Zone 1 / Zone 2

II 2 G X/Ex h II Gb X

Notified body details and role:

This Declaration of Conformity /

Incorporation is issued under the sole responsiblity of the manufacturer:

Element Materials Technology (0891)

Lodging of Technical file

Carlisle Fluid Technologies UK Ltd,

Ringwood Road,

Bournemouth, BH11 9LH. UK

UKCA Declaration of Conformity

The object of the declaration described above is in conformity with the relevant British harmonisation legislation:

Equipment and Protective Systems Intended for use in Potentially Explosive Atmospheres Regulations 2016

Supply of Machinery (Safety) Regulations 2008 by complying with the following statutory documents and harmonised standards:

BS EN 1127-1:2011 Explosive atmospheres - Explosion prevention - Basic concepts

BS EN 1953:2013 Atomising and spraying equipment for coating materials - Safety requirements

BS EN ISO 12100:2010 Safety of Machinery - General Principles for Design

BS EN ISO 80079-36:2016 Explosive Atmospheres- Part 36:Non Electrical equipment for explosive atmospheres-

Basic methods and requirements.

BS EN ISO 80079-37:2016 Explosive Atmospheres- Part 37: Non Electrical equipment for explosive atmospheres -

protection by methods "c", "b" and "k".

Providing all conditions of safe use/installation stated within the product manuals have been complied with and also installed in accordance with any applicable local codes of practice.

Vice President of Engineering

Signed for and on behalf of Carlisle Fluid

Technologies UK Ltd:

SB-E-2-984 R1.0

4/24

M.Munoz

31/3/21 www.carlisleft.com

In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasise important safety information as follows:

WARNING CAUTION NOTE

EN

Hazards or unsafe practices which could result in severe personal injury, death or substantial property damage.

Hazards or unsafe practices which could result in minor personal injury, product or property damage.

Important installation, operation or maintenance information.

WARNING

Read the following warnings before using this equipment.

SOLVENTS AND COATING MATERIALS. Can be highly flammable or combustible when sprayed. Always refer to the coating supplier's instructions and safety sheets before using this equipment.

INSPECT THE EQUIPMENT DAILY. Inspect the equipment for worn or broken parts on a daily basis. Do not operate the equipment if you are uncertain about its condition.

READ THE MANUAL. Before operating finishing equipment, read and understand all safety, operation and maintenance information provided in the operation manual. Users must comply with all local and national codes of practice and insurance company requirements governing ventilation, fire precautions, operation and house-keeping of working areas.

EQUIPMENT MISUSE HAZARD. Equipment misuse can cause the equipment to rupture, malfunction or start unexpectedly and result in serious injury.

FIRE AND EXPLOSION HAZARD. Never use 1,1,1-Trichloroethane,

Methylene Chloride, other Halogenated Hydrocarbon solvents or fluids containing such solvents in equipment with aluminium wetted parts. Such use could result in a serious chemical reaction, with the posibility of explosion.

Consult your fluid suppliers to ensure that the fluids being used are compatible with aluminium parts.

GLOVES. Must be worn when spraying or cleaning the equipment.

WEAR SAFETY GLASSES. Failure to wear safety glasses with side shields could result in serious eye injury or blindness.

STATIC CHARGE. Fluid may develop a static charge that must be dissipated through proper grounding of the equipment, objects to be sprayed and all other electrically conductive objects in the dispensing area. Improper grounding or sparks can cause a hazardous condition and result in fire, explosion or electric shock and other serious injury.

TOXIC VAPOURS. When sprayed, certain materials may be poisonous, create irritation, or are otherwise harmful to health. Always read all labels, safety sheets and follow any recommendations for the material before spraying. If in doubt contact your material supplier.

LOCK OUT / TAG-OUT. Failure to de-energise, disconnect, lock out and tagout all power sources before performing equipment maintenance could cause serious injury or death.

WEAR RESPIRATOR. The use of respiratory protective equipment is recommended at all times. The type of equipment must be compatible with the material being sprayed.

NEVER MODIFY THE EQUIPMENT. Do not modify the equipment unless the manufacturer provides written approval.

PROJECTILE HAZARD. You may be injured by venting liquids or gases that are released under pressure, or flying debris.

NOISE LEVELS. The A-weighted sound level of pumping and spray equipment may exceed 85 dB(A) depending on equipment settings. Actual noise levels are available on request. It is recommended that ear protection is worn at all times while equipment is in use.

PRESSURE RELIEF PROCEDURE. Always follow the pressure relief procedure in the equipment instruction manual.

KNOW WHERE AND HOW TO SHUT OFF THE EQUIPMENT

IN CASE OF AN EMERGENCY.

HIGH PRESSURE CONSIDERATION. High pressure can cause serious injury. Relieve all pressure before servicing. Spray from the gun, hose leaks or ruptured components can inject fluid into your body and cause extremely serious injury.

OPERATOR TRAINING. All personnel must be trained before operating finishing equipment.

IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PROVIDE THIS INFORMATION TO THE OPERATOR OF THE EQUIPMENT.

SB-E-2-984 R1.0

5/24

www.carlisleft.com

EXPLODED VIEW

EN

PARTS LIST

REF.

PART No.

1

2

3

4

5

6

DESCRIPTION

-

-

-

704472

-

704480

RETAINING RING

SLIP RING

RETAINING RING SEAL

RETAINING RING SUB ASSEMBLY

AIR CAP

SPRING CLIP (KIT OF 5)

7 SEE TABLE 1 AIR CAP & RETAINING RING

8 SEE TABLE 2 FLUID NOZZLE

SB-E-2-984 R1.0

6/24

QTY.

1

1

1

1

1

1

1

1 www.carlisleft.com

32

44

45

46

47

40

41

42

43

33

34

35#+

36

37

38

39

22*

23#

24

25#

26

27

28+

29

30

31

17+

18

19

20

21*

9

10+

11

12+

13

14

15

16

PARTS LIST (Continued)

REF.

PART No.

DESCRIPTION

-

-

704469

-

-

-

704470

704471

-

-

704473

704464

704403

-

704463

704462

-

905294

-

-

-

-

-

DEFLECTOR PLATE

SCREW (KIT OF 3)

SPRAYHEAD

GASKET (KIT OF 2)

SPRAY HEAD KIT

NEEDLE PACKING

PACKING SPRING

PACKING NUT

PACKING, SPRING & PACKING NUT KIT

O RING

AIR VALVE CAGE

SEAL

SEAL GUIDE

VALVE SEAT

FRONT CAGE ASSEMBLY

AIR VALVE STEM

AIR VALVE SPRING

REAR SEAL HOUSING

REAR SEAL ASSEMBLY

AIR VALVE ASSEMBLY

IDENTIFICATION SLEEVE

SLEEVE NUT

SLEEVE KIT

SEE TABLE 2 FLUID NEEDLE

-

-

704405

704465

-

-

-

-

704417

-

-

-

-

-

704466

NEEDLE SPRING

SPRING PAD

NEEDLE SPRING KIT

FLUID ADJUSTING KNOB

O RING

FLOW VALVE BODY

FLOW VALVE KNOB

CIRCLIP

INLINE FLOW VALVE

PLUG

TRIGGER SCREW

SPRING

TRIGGER STUD

TRIGGER

TRIGGER, STUD, SPRING & SCREW KIT

SB-E-2-984 R1.0

7/24

EN

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

QTY.

1

1

1

1

2

2

1

1

1

1

1

1

1

3

1

1

1

1

1

1

1

1

1 www.carlisleft.com

PARTS LIST (Continued)

REF.

PART No.

DESCRIPTION

48

49#+

50

51#+

52

53#+

54

55

-

-

-

-

-

-

-

704468

56

57

58

59

60

704467

-

-

-

704474

* NOT REPLACEABLE

SCREW

SPREADER VALVE PIN

SPREADER VALVE STEM

O RING

VALVE BODY

O RING

SPREADER VALVE ADJUSTING KNOB

SPREADER KNOB KIT

SPREADER VALVE ASSEMBLY

VALVE TOOL

TORX DRIVER

TIP WRENCH

TOOL KIT

GRAVITY CUP

PART No.

905202

905308

905309

905311

905312

DRIP CHECK LID (KIT OF 5)

GRAVITY CUP LID (KIT OF 2)

FILTER (KIT OF 3)

GRAVITY CUP KIT

FUNNEL (KIT OF 12)

DESCRIPTION

SERVICE PARTS

704475 MINOR SERVICE KIT

704476 MAJOR SERVICE KIT

INCLUDES ITEMS MARKED #

INCLUDES ITEMS MARKED +

WARNING

QTY.

1

1

1

1

1

The spray gun must be earthed to dissipate any electrostatic charges which may be created by fluid or air flows. This can be achieved through the spray gun mounting, or conductive air/fluid hoses.

Electrical bond from the spray gun to earth should be checked and a resistance of less than 10⁶ Ohms is required.

QTY.

1

1

1

1

1

1

1

1

1

1

1

1

1

EN

SB-E-2-984 R1.0

8/24

www.carlisleft.com

EN

DV1 S - PART SELECTION GUIDE

TABLE 1 – DV1 S AIR CAP PERFORMANCE GUIDE

Part Number

704451 M1

Air Cap & Type

HVLP MICRO

Recommended Air Inlet

Pressure

Air Consumption

L/min

1.0 bar [15 psi] 50 [1.8 cfm]

Typical Fluid

Flow*

1 - 50 ml/min

Typical Fan Pattern Size**

60mm

704452 S1 HVLP PLUS 2.0 bar [29 psi] 115 [4.1 cfm] 5 - 125 ml/min

704453 S2 HVLP 2.0 bar [29 psi] 130 [4.6 cfm]

*

**

Flow rates may vary according to paint/material and pressure used.

Fan pattern size @ 50-100mm [2-4"] distance.

5 - 125 ml/min

200mm

180mm

TABLE 2 – DV1 S FLUID NOZZLE & NEEDLES

Fluid Nozzle

Part Number

704454

704455

704456

704457

704458

Fluid Nozzle Size

0.7 mm

0.9 mm

0.8 mm

1.0 mm

1.2 mm

Marking

DV1 0.7M

DV1 0.9M

DV1 0.8S

DV1 1.0S

DV1 1.2S

Part Number

704460

704459

Needle

TABLE 3 – DV1 S RECOMMENDED FLUID NOZZLE / AIR CAP COMBINATIONS

M1

S1

S2

Air Cap & Type

HVLP MICRO

HVLP PLUS

HVLP

0.7 M

✔

-

-

0.9 M

✔

-

-

Fluid Nozzle Size

0.8 S

-

✔

✔

1.0 S

-

✔

✔

Marking

DV1-M

DV1-S

1.2 S

-

✔

✔

TABLE 4 – DV1 S AIR CAP TEST KITS

Part Number

704477

704478

704479

Recommended Air Inlet Pressure

M1

S1

S2

Air Cap & Type

HVLP MICRO

HVLP PLUS

HVLP

(with gun fully triggered)

1.0 bar [15 psi]

2.0 bar [29 psi]

2.0 bar [29 psi]

At Gun Handle

Atomisation Pressure

0.69 bar [10 psi]

0.69 bar [10 psi]

0.69 bar [10 psi]

SB-E-2-984 R1.0

9/24

www.carlisleft.com

CAUTION

IMPORTANT: This spraygun is suitable for use with both waterbased and solvent based coating materials.

• The gun is not designed for use with highly corrosive and/or abrasive materials.

EN

• To avoid premature degradation of parts, DeVilbiss recommends the gun is washed in neutral cleaning solution (pH 6 to 8).

• The gun is not designed to be cleaned within an ultrasonic bath.

If there is any doubt regarding the suitability of a specific material, contact your DeVilbiss Distributor or DeVilbiss direct.

START-UP SEQUENCE

1. Connect the gun to a clean, moisture and oil free air supply using a conductive hose of at least

8mm I.D.

2. Mix coating material to Manufacturer's instructions and strain material.

3. Turn fluid adjusting knob (36) clockwise to prevent fluid needle movement.

4. Turn spreader valve adjusting knob (54) counter clockwise to fully open.

5. Adjust inlet air pressure if required.

6. Turn fluid adjusting knob counter clockwise until first thread shows.

7. Test spray. If the finish is too dry, reduce airflow by reducing air inlet pressure.

8. If finish is too wet, reduce fluid flow by turning fluid adjusting knob (36) clockwise. If atomisation is too coarse, increase air inlet pressure. If too fine, reduce inlet pressure.

9. The pattern size can be reduced by turning spreader valve knob (54) clockwise.

10. Hold gun perpendicular to surface being sprayed. Arcing or tilting may result in uneven coating.

11. The recommended spray distance is 50-100mm.

12. Spray edges first. Overlap each stroke a minimum of 75%. Move gun at a constant speed.

13. Always turn off air supply and relieve pressure when gun is not in use.

SB-E-2-984 R1.0

10/24

www.carlisleft.com

EN

NOTE

Depending on hose length, larger I.D. hose may be required. Install an air gauge at the gun handle.

When gun is triggered on, adjust regulated pressure as required. Do not use more pressure than is necesarry to atomise the material being applied. Excess pressure will create additional overspray and reduce transfer efficiency.

NOTE

If quick connect couplings are required, use only high flow quick connects. Other types will not flow enough air for correct gun operation.

SPRAY GUN MAINTENANCE & CLEANING

To clean air cap and fluid tip, brush exterior with a stiff bristle brush. If necesarry to clean cap holes, use a broom straw or toothpick if possible. If a wire or hard instrument is used, extreme care must be taken to prevent scratching or burring of the holes which will cause a distorted spray pattern.

To clean fluid passages, remove excess material, then flush with gun wash solution. Wipe the gun exterior with a dampened cloth. Never completely immerse in any solvent or cleaning solutions as this is detrimental to the lubricants and life of the spray gun.

SB-E-2-984 R1.0

11/24

www.carlisleft.com

EN

SPRAY GUN DISASSEMBLY / ASSEMBLY

#

KEY

Order for disassembly

(reverse for assembly)

DISASSEMBLY TIP & NEEDLE

18mm HEX

11 Nm

[97.5 in-lbs]

✓

NOTE

When replacing the fluid tip or fluid needle, replace tip, needle and fluid packing at the same time.

Using worn parts can cause fluid leakage. Do not overtighten.

NOTE

When removing air cap from retaining ring, do not remove slip ring or retaining ring seal from retaining ring. Damage to the parts may occur.

The slip ring and retaining ring seal are not available as replacement parts.

Simply wipe parts clean and reassemble with new or clean air cap.

SB-E-2-984 R1.0

12/24

www.carlisleft.com

DISASSEMBLY PACKING

EN

DISASSEMBLY TRIGGER

T10 TORX

1 Nm [10 in-lbs]

SB-E-2-984 R1.0

13/24

www.carlisleft.com

DISASSEMBLY SPRAYHEAD

T10 TORX

1 Nm [10 in-lbs]

DISASSEMBLY FLOW VALVE

SB-E-2-984 R1.0

14/24

7mm HEX

15 Nm

[133 in-lbs] www.carlisleft.com

EN

EN

DISASSEMBLY AIR VALVE

12 Nm

[110 in-lbs]

6mm HEX

18 Nm [160 in-lbs]

TO CHANGE IDENTIFICATION SLEEVE ONLY

1 2 4 5

SPREADER VALVE REPLACEMENT

9mm HEX

6 Nm [53 in-lbs]

SB-E-2-984 R1.0

15/24

T10 TORX

1 Nm

[10 in-lbs] www.carlisleft.com

EN

TROUBLESHOOTING MECHANICAL PERFORMANCE

GENERAL FAULTS CAUSE CORRECTION

No air pressure at gun.

Check air supply and air line.

Will not spray.

Fluid needle adjustment knob not open enough.

Open fluid needle adjustment knob.

Incorrect needle fitted to gun.

Gun spits paint when triggering on and off.

Excessive needle wear.

Excessive fluid nozzle wear.

Check fluid nozzle/needle selection chart and fit correct item.

Replace with new needle.

Replace with new fluid nozzle.

Gun spits paint when triggering on due to paint build-up inside air cap between spraying operations.

Fluid nozzle not fitted correctly in gun head.

Fluid nozzle/needle leakage.

Tighten.

Check for damage or blockage.

Fluid nozzle not fitted correctly in gun head.

Tighten.

Paint build-up on fluid tip.

Fluid nozzle/needle leakage.

Check for damage or blockage.

Damaged air cap holes.

Replace with new air cap.

Paint build-up on air cap.

Gradual build-up of bounce-back on gun head.

Thoroughly clean.

Unable to get round spray

Fluid nozzle or sprayhead incorrectly fitted.

Remove, check components for damage and refit correctly.

SB-E-2-984 R1.0

16/24

www.carlisleft.com

EN

When removing air cap from retaining ring, do not remove the ring seat from the retaining ring.

Damage to the parts may occur. Simply wipe parts clean and reassemble with new or clean air cap.

FLUID FAULTS CAUSE

Fluid nozzle internal seat scored damaged or worn.

Replace.

CORRECTION

Fluid needle external profile damaged or worn.

Replace.

Contamination on needle or tip mating surfaces preventing good seal.

Thoroughly clean.

Slow fluid leak from fluid nozzle and needle seat.

Incorrect fluid nozzle for fluid needle fitted to gun.

Check nozzle/needle selection chart and fit correct item.

Sluggish needle.

Lubricate packing.

Tight packing nut.

Adjust.

Major fluid leak or fluid jetting from fluid nozzle and needle seat.

Contamination on needle or tip mating surfaces preventing good seal.

Remove nozzle and needle and thoroughly clean.

Incorrect fluid nozzle for fluid needle fitted to gun.

Check nozzle/needle selection chart and fit correct item.

Slow fluid leak from needle packing.

Fluid needle packing worn or loose.

Tighten or replace as necessary.

SB-E-2-984 R1.0

17/24

www.carlisleft.com

EN

AIR FAULTS CAUSE CORRECTION

Air Valve Stem contaminated and not correctly seating.

Remove Air Valve Stem and thoroughly clean valve shaft and seating surfaces.

Small air leak from air cap when gun is not triggered.

Air Valve Stem seal damaged or missing.

Replace.

SB-E-2-984 R1.0

18/24

www.carlisleft.com

TROUBLESHOOTING SPRAY PERFORMANCE

CONDITION

Heavy top or bottom pattern.

CAUSE CORRECTION

Paint or coating build-up on air cap, plugged horn holes, centre holes or jets.

Soak cap or nozzle in suitable solvent and thoroughly clean.

EN

Heavy right or left side pattern.

Paint or coating build-up on fluid nozzle exterior or partially plugged fluid tip.

Replace fluid nozzle or air cap if necessary.

Fluid nozzle or cap dirty or damaged.

Replace fluid nozzle or air cap if necessary.

Left or right side horn holes plugged.

Soak cap or nozzle in suitable solvent and thoroughly clean.

Dirt or damage on left or right side of fluid nozzle exterior.

Replace fluid nozzle or air cap if necessary.

Remedies for the top-heavy, bottom-heavy, right-heavy and left-heavy patterns.

Determine if the obstruction is on the air cap or the fluid nozzle. Do this by making a test spray pattern. Then, rotate the cap one-half turn and spray another pattern. If the defect is inverted, obstruction is on the air cap.

Clean the air cap as previously instructed. Also check for dried paint just inside the cap centre hole opening, remove by washing with solvent.

If the defect is not inverted, it is on the fluid nozzle. Clean nozzle. If problem persists, renew nozzle.

SB-E-2-984 R1.0

19/24

www.carlisleft.com

Heavy centre pattern.

Intermittent or 'fluttering' spray fan.

Split spray pattern

Pattern adjustment valve set too low.

Turn out counter clockwise to achieve correct pattern.

EN

Too much paint or coating.

Reduce fluid flow by turning fluid needle adjusting screw clockwise.

Reduce fluid pressure.

Paint or coating too thick.

Thin to correct consistency.

Atomizing air pressure too low.

Increase air pressure.

Loose fluid nozzle.

Tighten.

Fluid nozzle not seated correctly in gun head.

Remove fluid nozzle, clean components, check cone seating on tip and gun for damage or contamination.

Partially obstructed fluid passage or hose.

Clean or replace.

Not enough paint or coating flow.

Increase fluid flow by changing fluid nozzle size, opening needle control knob or increase fluid pressure on pressure feed container.

SB-E-2-984 R1.0

Too high horn pressure.

Reduce air pressure by rotating pattern control valve clockwise.

Too much air for fluid quanitity used.

Reduce input air pressure.

20/24

www.carlisleft.com

Ball end heavy pattern.

Too much fluid flow.

EN

Change fluid nozzle for smaller size or change air cap for different specification air cap.

Excessive bounce-back.

Too much atomization air pressure.

Reduce air pressure.

Gun too far from surface.

Check distance (normally 150-

200mm [6-8"]).

Too much fluid flow.

Paint or coating too thin.

Runs and sags.

Gun tilted at an angle.

Gun too far from surface.

Thin, sandy coarse finish drying before it flows out.

Too much air pressure.

Fluid flow too low.

Adjust gun or reduce fluid pressure.

Mix properly or apply light coats/reduce fluid flow.

Mount gun at right angle to work.

Check distance.

Reduce air pressure and check spray pattern.

Increase fluid flow by changing fluid nozzle size, supply pressure or turning needle control knob counter clockwise.

SB-E-2-984 R1.0

21/24

www.carlisleft.com

DIMENSIONS

EN

SB-E-2-984 R1.0

22/24

www.carlisleft.com

NOTES

EN

SB-E-2-984 R1.0

23/24

www.carlisleft.com

EN

WARRANTY POLICY

This product is covered by Carlisle Fluid Technologies’ materials and workmanship limited warranty. The use of any parts or accessories, from a source other than Carlisle Fluid

Technologies, will void all warranties. Failure to reasonably follow any maintenance guidance provided, may invalidate any warranty.

For specific warranty information please contact Carlisle Fluid Technologies.

For technical assistance or to locate an authorised distributor, contact one of our international sales and customer support locations below.

Region Industrial / Automotive Automotive Refinishing

Americas

Tel: 1-888-992-4657

Fax: 1-888-246-5732

Tel: 1-800-445-3988

Fax: 1-800-445-6643

Europe, Africa,

Middle East,

India

Tel: +44 (0)1202 571 111

Fax: +44 (0)1202 573 488

China

Japan

Tel: +8621-3373 0108

Fax: +8621-3373 0308

Tel: +81 45 785 6421

Fax: +81 45 785 6517

Australia

Tel: +61 (0) 2 8525 7555

Fax: +61 (0) 2 8525 7575

For the latest information about our products, visit www.carlisleft.com

Carlisle Fluid Technologies is a global leader in innovative finishing technologies.

Carlisle Fluid Technologies reserves the right to modify equipment specifications without prior notice.

BGK™, Binks®, DeVilbiss®, Hosco®, MS®, and Ransburg® are registered trademarks of Carlisle

Fluid Technologies, Inc.

© 2020 Carlisle Fluid Technologies,Inc.

All rights reserved.

SB-E-2-984 R1.0

24/24

www.carlisleft.com