A
A
K
K
DPAK
A
A
Product label
STPST10H100SB-Y
Datasheet
Automotive 100 V - 10 A DPAK power Schottky trench rectifier
Features
•
•
•
•
•
•
•
•
•
AEC-Q101 qualified
PPAP capable
ST trench patented process
Low forward voltage drop
Low recovery charges
Reduces conduction, reverse and switching losses
100% Avalanche tested in production
Operating T j
from -40 °C to +175 °C
ECOPACK2 compliant
Applications
•
•
•
•
Automotive LED lighting
Flyback topology
On-board DC/DC converter
ECU power supply
Description
This 10 A, 100 V rectifier is based on ST trench technology that achieves the bestinclass V
F
/I
R
trade-off for a given silicon surface.
Integrated in a DPAK package, this STPST10H100SB-Y trench, and automotivegraded device is intended to be used in high frequency miniature switched mode power supplies such as in automotive, DC/DC converters or ECU power supply. It is also adapted to freewheeling applications, OR-ring, or reverse polarity protection.
Product status link
STPST10H100SB-Y
I
F(AV)
V
RRM
Product summary
10 A
T j
(max.)
V
F
(typ.)
100 V
175 °C
0.570 V
DS14178 - Rev 1 - December 2022
For further information contact your local STMicroelectronics sales office.
www.st.com
1
STPST10H100SB-Y
Characteristics
Characteristics
Table 1. Absolute ratings (limiting values at 25 °C, unless otherwise specified, with 2 anode terminals short-circuited)
Symbol
V
RRM
I
F(RMS)
I
I
F(AV)
I
FSM
AS
Repetitive peak reverse voltage (T
Forward rms current
Single pulse avalanche current (1)
j
Parameter
= -40°C to + 175°C)
Average forward current, δ = 0.5 square wave
Surge non repetitive forward current
T c
= 165 °C t p
= 10 ms sinusoidal
T j
= 25°C, L = 300 µH,
V
DD
= 15 V
Value
100
45
10
210
14
T stg
T j
Storage temperature range
Maximum operating junction temperature range (2)
-65 to +175
-40 to +175
1. Please refer to Figure 1 and Figure 2
for the unclamped inductive switching test circuit, and waveform.
2. (dP tot
/dT j
) < (1/R th(j-a)
) condition to avoid thermal runaway for a diode on its own heatsink.
A
Unit
V
A
A
A
°C
°C
Symbol
R th(j-c)
Junction to case
Table 2. Thermal resistance parameter
Parameter Typ. value
0.7
Unit
°C/W
For more information, please refer to the following application note:
• AN5088 : Rectifiers thermal management, handling and mounting recommendations
Symbol
I
R
(1)
V
F
(2)
Parameter
Reverse leakage current
Forward voltage drop
Table 3. Static electrical characteristics
T j
= 125 °C
T j
= 25 °C
T j
= 125 °C
T j
= 25 °C
T j
= 125 °C
T j
= 25 °C
T j
= 125 °C
Test conditions
V
R
= 70 V
I
I
V
F
F
R
= 100 V
= 5 A
= 10 A
1. Pulse test: t p
= 5 ms, δ < 2%
2. Pulse test: t p
= 380 µs, δ < 2%
•
•
To evaluate the conduction losses, use the following equation:
P = 0.435 x I
F(AV)
+ 0.019 x I
F
2
(RMS)
For more information, please refer to the following application notes related to the power losses :
AN604 : Calculation of conduction losses in a power rectifier
AN4021 : Calculation of reverse losses on a power diode
-
-
-
Min.
Typ.
Max.
Unit
-
2.0
6.4
26 mA
µA
-
4.0
13.5
0.545 0.605
mA
0.470 0.530
0.645 0.715
0.570 0.625
V
DS14178 - Rev 1 page 2/9
DS14178 - Rev 1
STPST10H100SB-Y
Characteristics
Figure 1. Current and voltage waveforms for avalanche energy test across D.U.T (device under test) i(t), v(t)
V
CL_DUT
I
AS
I
L
I
DUT t p
Figure 2. Unclamped Inductive Switching Test circuit t
EAS = 12 × L × IAS² × tp =
L × IAS
VCLDUT − VDD
VCLDUT
VCLDUT − VDD ≅
1
2 × L × IAS² page 3/9
STPST10H100SB-Y
Characteristics (curves)
1.1
Characteristics (curves)
30
25
20
15
10
5
0
0
Figure 3. Average forward current versus case temperature (δ = 0.5)
35
I
F(AV)(
A)
25 50 75 100 125
T c
(°C)
150 175
Figure 4. Relative variation of thermal impedance junction to case versus pulse duration
1.0
Z th(j-c)
/R th(j-c)
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
1.E-04
Single pulse
1.E-03 1.E-02 t
P
(s)
1.E-01
Figure 5. Reverse leakage current versus reverse voltage applied (typical values)
1.E+05
I
R
(µA)
1.E+04
1.E+03
1.E+02
T j
=150°C
T j
=125°C
T j
=100°C
T j
=75°C
T j
=50°C
1.E+01
T j
=25°C
1.E+00
1.E-01
0 10 20 30 40 50 60 70 80
V
R
(V)
90 100
Figure 6. Junction capacitance versus reverse voltage applied (typical values)
10000
C(pF)
F=1MHz
V
OSC
T j
=30mV
RMS
=25°C
1000
100
0.1
1.0
10.0
V
R
(V)
100.0
Figure 7. Forward voltage drop versus forward current
(typical values)
100.0
I
F
(A)
10.0
1.0
T j
= 25 °C
T j
= 75 °C
T j
= 125 °C
T j
= 150 °C
T j
= -40 °C
0.1
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
V
F
(V)
0.9
Figure 8. Thermal resistance junction to ambient versus copper surface under tab (typical values, epoxy printed board FR4, e
Cu
= 70 µm)
30
20
10
0
0
70
60
50
40
100
Rth(j-a)(°C/W)
90
80
5 10 15 20 25 30
DPAK
35
S
Cu
(cm²)
40
DS14178 - Rev 1 page 4/9
2
2.1
STPST10H100SB-Y
Package information
Package information
In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com
. ECOPACK is an ST trademark.
•
DPAK package information
Epoxy meets UL94, V0
Figure 9. DPAK package outline
Note:
E b4 c2
A
L2
H
L4
D e e1
Seating plane
A1 b (2x)
A2
L
0.25
V2
Gauge
plane
(L1) c
R
D1
E1
This package drawing may slightly differ from the physical package. However, all the specified dimensions are guaranteed.
DS14178 - Rev 1 page 5/9
STPST10H100SB-Y
DPAK package information
Table 4. DPAK mechanical data
Dimensions
Dim.
Millimeters
Typ.
H
L
(L1) c2
D
D1
E
E1 e e1
A
A1
A2 b b4 c
L2
L4
R
V2 0°
5.10
4.70
2.286
4.572
2.80
0.80
0.20
1. Inches dimensions given for reference only
9.35
1.00
2.60
0.65
0.60
4.95
6.40
4.60
2.159
4.445
0.64
5.20
0.45
0.48
6.00
Min.
2.20
0.90
0.03
8° 0°
10.10
1.50
3.00
0.95
1.00
5.25
6.60
4.80
2.413
4.699
0.90
5.40
0.60
0.60
6.20
Max.
2.40
1.10
0.23
0.368
0.039
0.102
0.026
0.024
0.195
0.252
0.181
0.085
0.175
Min.
0.087
0.035
0.001
0.025
0.205
0.018
0.019
0.236
Inches (1)
Typ.
0.201
0.185
0.090
0.180
0.110
0.031
0.008
Figure 10. DPAK recommended footprint (dimensions are in mm)
8°
0.398
0.059
0.118
0.037
0.039
0.207
0.260
0.189
0.095
0.185
Max.
0.094
0.043
0.009
0.035
0.213
0.024
0.024
0.244
Note: For package and tape orientation, reel and inner box dimensions and tape outline please check TN1173
DS14178 - Rev 1 page 6/9
3
STPST10H100SB-Y
Ordering information
Ordering information
Order code
STPST10H100SBYTR
Table 5. Ordering information
Marking
STPST 10H1Y
Package
DPAK
Weight
0.32 g
Base qty.
2500
Delivery mode
Tape and reel
DS14178 - Rev 1 page 7/9
Revision history
Date
16-Dec-2022
Revision
1
Table 6. Document revision history
Changes
Initial release.
STPST10H100SB-Y
DS14178 - Rev 1 page 8/9
STPST10H100SB-Y
IMPORTANT NOTICE – READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgment.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, refer to www.st.com/trademarks . All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2022 STMicroelectronics – All rights reserved
DS14178 - Rev 1 page 9/9
