Lithonia Lighting Contractor Select EU2C Emergency Light Installation Instructions

*/45"--"5*0/*/4536$5*0/4GPS-JUIPOJB-JHIUJOH&6$.PEFMT

LED DUAL HEAD EMERGENCY LIGHTING FIXTURE

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS

AND WARNINGS MAY RESULT IN DEATH, SERIOUS INJURY OR

SIGNIFICANT PROPERTY DAMAGE. For your protection, read and follow these warnings and instructions carefully before installing or maintaining this equipment. These instructions do not attempt to cover all installation and maintenance situations. If you do not understand these instructions or additional information is required, contact

LITHONIA LIGHTING or your local LITHONIA LIGHTING distributor.

WARNING: RISK OF ELECTRIC SHOCK - NEVER CONNECT

TO, DISCONNECT FROM, OR SERVICE WHILE EQUIPMENT IS

ENERGIZED.

WARNING: RISK OF FIRE. Lamps are hot. Keep combustible material away from hot parts. Observe lamp manufacturer’s warnings, recommendations and restrictions on lamp operation and maintenance. Make sure lamps are correctly installed.

CAUTION: The battery in this unit may not be fully charged. After electricity is connected to unit, let battery charge for at least 24 hours, then normal operation of this unit should take effect. To check, press the TEST button. The lamps on the unit should turn on.

127(

:

&RPSOLHVZLWK&DOLIRUQLD7LWOH3URGXFWODEHOLVPDUNHGZLWK

IMPORTANT SAFEGUARDS: When using electrical equipment, basic safety precautions should always be followed, including the following:

• Do not use outdoors.

• Consult local building code for approved wiring and installation.

• Disconnect AC power before servicing and installation.

• Do not mount near gas or electric heaters.

• Do not use this equipment for anything other than its intended use.

• The use of accessory equipment not recommended by the manufacturer will void product listing and warranty and may cause an unsafe condition.

• Any service on this equipment should be performed by

TXDOLILHGSHUVRQQHORQO\

• Equipment should be mounted in locations and at heights where it will not be subject to tampering by unauthorized personnel.

•

'RQRWFHLOLQJPRXQW

• Use caution when servicing batteries.

• Cap unused wires with enclosed wire nuts or other approved method.

• Make sure wire terminations are secure and leads are properly tucked in appropriate wire channels.

INSTALLATION:

NOTE:

0D[PRXQWLQJKHLJKWLVIWWRDFKLHYHDWOHDVWIWFDQGOHRILOOXPLQDQFHLQHPHUJHQF\PRGH

PAGE: 1 of

BATTERY CONNECTOR

PLUG IN

Fig.A (J-Box) Fig.B

SAVE THESE INSTRUCTIONS and deliver to owner after installation

Fig.C

INSTALLATION INSTRUCTIONS

J-BOX MOUNTING:

)HHG¿[WXUHOHDGVWKURXJKWKHEDFNSODWHDQGFRQQHFWWR$&SRZHUVXSSO\)LJ$SDJH)RU9XVHEODFNDQGZKLWHZLUHV

DQGIRU9XVHUHGDQGZKLWHZLUHV

Attach back plate to J-Box and secure with screws.

Complete the battery connection. (Fig. B

SDJH

)

Align snaps and push housing directly onto the back plate (Fig. C

SDJH

). Apply continuous AC power.

After the battery has been left to charge for 24 hours, test the unit by pushing the test switch and the LED lamp head will

WXUQ

ON.

CONDUIT MOUNTING:

6HFXUHEDFNSODWHWRZDOOVXUIDFHXVLQJNH\KROHNQRFNRXWVRQWKHEDFNSODWH

5RXWHZLUHVWKURXJKKROHLQFRQGXLWIODQJHDQGPDNHFRQGXLWFRQQHFWLRQ)RU9XVHEODFNDQGZKLWHZLUHVDQGIRU9XVH

UHGDQGZKLWHZLUHV

&RPSOHWHWKHEDWWHU\FRQQHFWLRQ)LJ%SDJH

$OLJQVQDSVDQGSXVKKRXVLQJGLUHFWO\RQWRWKHEDFNSODWH$SSO\FRQWLQXRXV$&SRZHU

$IWHUEDWWHU\KDVEHHQOHIWWRFKDUJHIRUKRXUVWHVWWKHXQLWE\SXVKLQJWKHWHVWVZLWFKDQGWKH/('ODPSKHDGZLOOWXUQ21

WALL MOUNTING:

6HFXUHEDFNSODWHWRZDOOVXUIDFHXVLQJNH\KROHNQRFNRXWVRQWKHEDFNSODWH

)HHGIL[WXUHOHDGVWKURXJKEDFNSODWHDQGFRQQHFWWR$&SRZHUVXSSO\)RU9XVHEODFNDQGZKLWHZLUHVDQGIRU9XVH

UHGDQGZKLWHZLUHV

&RPSOHWHWKHEDWWHU\FRQQHFWLRQ)LJ%SDJH

$OLJQVQDSVDQGSXVKKRXVLQJGLUHFWO\RQWRWKHEDFNSODWH$SSO\FRQWLQXRXV$&SRZHU

$IWHUEDWWHU\KDVEHHQOHIWWRFKDUJHIRUKRXUVWHVWWKHXQLWE\SXVKLQJWKHWHVWVZLWFKDQGWKH/('ODPSKHDGZLOOWXUQ21

23(5$7,21

During an electrical power failure, the LED lamps will automatically come on for a minimum of 90 minutes.

5PUFTUQSFTTUIF5&45TXJUDI5IFFNFSHFODZ-&%MBNQTXJMMJMMVNJOBUFBOE-&%JOEJDBUPSXJMMUVSO0''8IFOUIFTXJUDI

JTSFMFBTFEUIFMBNQTXJMMUVSO0''BOEUIF-&%JOEJDBUPSXJMMUVSO0/

/('67$786,1',&$725.(<DQG7528%/(6+227,1*

Visual Status Indica

Ɵ on

RED ϭ͘

Ba

Ʃ ery connec

Ɵ on is not made.

Ϯ͘

Ba

Ʃ ery has been diagnosed as dead or defec

Ɵ ve a

Ō er 24 hours of con

Ɵ nuous charging with AC power supplied.

GREEN

UNLIT

Ba

Ʃ ery is connected, AC power has been supplied and

Į xture is in charging state.

AC power has not been supplied.

Troubleshoo

Ɵ ng/Ac

Ɵ ons to Take ϭ͘

Make connec

Ɵ on; or if ba

Ʃ ery is connected, disconnect ba

UU ery for eight seconds and then reconnect.

Ϯ͘

Replace the ba UU ery.

This is the normal state. No ac

Ɵ on required.

Supply AC power.

7(67,1*

National Electric Code (NEC) and NFPA regulations require that routine tests need to be performed as listed below: Once every month, the unit needs to be tested for duration of 30 seconds. Push in and hold the test switch to perform this test. Once every 12 months, a full 90 minute (per UL requirements) test needs to be performed on the unit. Disconnect power to the unit and leave it in the emergency mode. The lamps should stay ON for at least 90 minutes. Written records of the testing are to be kept for examination by the authority having jurisdiction.

PAGE: of

SAVE THESE INSTRUCTIONS and deliver to owner after installation

7528%/(6+227,1*

Condition - The emergency lights do not operate

1.

If the charge indicator light is OFF: Check that the circuit breaker for AC supply is ON.

2.

If the charge indicator light is ON: Check that battery is properly connected. If problem persists, Replace battery. If remote lamps (where applicable) are connected to the equipment, then turn OFF the AC supply and disconnect the remote circuit wires from the equipment. Turn ON the

AC supply and depress the test switch. If the local lamps (mounted on the equipment itself) come ON, then check the remote circuit for short or overload condition and correct as required. Reconnect the circuit wires and restore AC power. If the local lamps don’t turn ON after disconnecting the remote circuit wires, then replace battery.

Condition - Emergency lights are dim

1.

Battery not fully charged. Allow battery to recharge for 24 hours and then retest. If lights are still dim, replace battery.

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

WIRING DIAGRAMS

REMOTE CAPABLE

AC INPUT CONNECTOR

(MOUNTING PLATE)

277V

120V

0V

RED

BLACK

WHITE

LAMP

YELLOW(+)

BLUE(-)

YELLOW(+)

BLUE(-)

LAMP

YELLOW(+)

BLUE(-)

CHARGER

BOARD

Note:

Unused input lead must be properly insulated with wire nut or other approved method.

AC INPUT CONNECTOR

(MOUNTING PLATE)

277V

120V

0V

RED

BLACK

WHITE

LAMP

YELLOW(+)

BLUE(-)

YELLOW(+)

BLUE(-)

CHARGER

BOARD

RED

BLACK

BATTERY

LAMP

TO REMOTE

READY

TEST

Note for HO models:

Use 18-22 AWG stranded wire to connect remote lamp heads.

READY

TEST

RED

BLACK

BATTERY

PAGE: of

SAVE THESE INSTRUCTIONS and deliver to owner after installation

INSTALLATION INSTRUCTIONS

AC INPUT CONNECTOR

(MOUNTING PLATE)

277V

120V

0V

RED

BLACK

WHITE

CHARGER

BOARD

YELLOW(+)

WHITE

BLUE(-)

LAMP

YELLOW(+)

WHITE

BLUE(-)

LAMP

READY

TEST

RED

BLACK

BATTERY

PAGE: of

One Lithonia Way, Conyers GA 30012

Phone: 800-334-8694 www.lithonia.com

SAVE THESE INSTRUCTIONS and deliver to owner after installation

3DUW1R(0&6$5(9%