CPS Products TLTWSM Metric Torque Wrench Kit (17-29mm Jaw Sizes) Owner's Manual

Torque Wrench Kit

#TLTWSM Metric

(17, 22, 24, 26, 27, 29mm)

Instructions for Use

Français, Español, Deutsch and latest updates: www.cpsproducts.com

cpsproducts.com

Wrench

Body

Torque

Values on

Vertical

Scale

Handle

Scale

Handle

Fig. 1

Removable

Wrench

End

Socket

Arrow

Indicates

Tightening

Direction

Pivot Point

Locking

Knob

Wrench Size and Arrow

Must Be

Same Side

Handle

Edge

BEFORE USE

• To retain wrench accuracy, DO NOT

LOOSEN nuts, bolts, etc. USE ONLY

FOR TIGHTENING.

• Apply a small amount of oil between handle and wrench body.

Note: If wrench is not used for an extended time, turn handle to lowest torque setting on wrench body. Rotate handle in both directions while making a few “clicks”. This re-lubricates the wrench.

INSTRUCTIONS

1.

Select Wrench from case.

2. Insert END into socket. Wrench size and arrow must be same side .

Fig. 1

3.

Loosen Locking Knob counterclockwise to unlock handle.

4.

Determine Proper Torque

Setting For Equipment Being

Serviced (use setting specified by equipment manufacturer).

5. Using Newton-Meter chart

Fig. 3 , twist handle and align appropriate handle mark with torque value on vertical scale.

6. For other settings, twist handle to advance by 1 or more detents to desired setting. (Each handle detent = 1 Nm).

7. Tighten Locking Knob clockwise to lock in your torque setting.

8. Tighten Equipment Fitting, Bolt,

Nut Until Clicks Are Felt/Heard

From Pivot Point Note: To prevent tool damage, avoid further pressure on wrench after torque (clicks) achieved.

2

Newton-Meter Scale (10-75)

Fig. 2

Shown is setting for 10 Nm

Center-line

Torque

Values

Handle Edge

Each mark on handle =

1Nm

UP

DOWN

HANDLE

Example 1: Set Torque Wrench to 14 Nm a) Twist handle until “10” mark aligns with Center-line and 10 Nm torque value.

b) Twist handle RIGHT 4 detents (1 detent = 1 Nm) stopping at the “4 th ” Mark on the Handle

(while aligned VERTICALLY with the Center-line). c) Final setting (10 + 1 + 1 + 1 + 1 = 14) d) Wrench is now set at 14 Nm.

10

10

10

10

10

+

Handle Scale Value

0

+1 detent

+2 detents

+3 detents

+4 detents

=

Final Torque Value

10

11

12

13

14

3

Fig. 3

Standard Newton/Meter Torque Settings On #TLTWSM

T orque

S eTTingS

(o n

W rench

B ody

)

H andle

S etting

S cale

A ccurAcy

75 Nm (100 Kg x cm)

65 Nm (100 Kg x cm)

55 Nm (100 Kg x cm)

42 Nm (100 Kg x cm)

18 Nm (100 Kg x cm)

10 Nm (100 Kg x cm)

0

42

18

10

0

0

+/- 4%

(All Settings)

STORAGE

1. Loosen Locking Knob.

Turn Knurled Handle to lowest torque setting on Body Scale.

2. Remove Wrench End and place all components back in Storage Case.

3. Store kit in dry location.

TLTWSM

TLXTWM

TLXTWMW

REPLACEMENT PARTS

Metric multi-head torque wrench set with handle, heads and case (17, 22, 24, 26, 27,

29 mm)

Set of metric wrench heads:

17, 22, 24, 26, 27, 29mm jaw sizes

Metric torque wrench handle

TLXTWM17 17mm Individual wrench head

TLXTWM22

TLXTWM24

TLXTWM26

TLXTWM27

TLXTWM29

22mm Individual wrench head

24mm Individual wrench head

26mm Individual wrench head

27mm Individual wrench head

29mm Individual wrench head

LOCATIONS

CPS PRODUCTS, INC. U.S.A. (Headquarters)

1010 East 31st Street,

Hialeah, Florida 33013, USA

Tel: 305-687-4121,

1-800-277-3808

Fax: 305-687-3743

E-mail: [email protected]

Website: www.cpsproducts.com

CPS PRODUCTS CANADA LTD.

1324 Blundell Road

Mississauga, ON, L4Y 1M5

Tel: 905.615.8620, Fax: 905.615.9745

E-mail: [email protected]

Website: www.cpsproducts.com

CPS PRODUCTS N.V

Krijgsbaan 241, 2070

Zwijndrecht, Belgium

Tel: (323) 281 30 40,

E-mail: [email protected]

CPS AUSTRALIA PTY. LTD.

109 Welland Avenue,

Welland, South Australia 5007

Tel: +61 8 8340 7055,

E-mail: [email protected]

For the latest update(s) to these instructions, go to www.cpsproducts.com

#73-166 Rev. E

092617JA