advertisement
Torque Wrench Kit
#TLTWSAE Imperial
( 5
/
8
, 11
/
16
, 13
/
16
, 15
/
16
, 1 1
/
16
, 1 5
/
16
)
Instructions for Use
Français, Español, Deutsch and latest updates: www.cpsproducts.com
cpsproducts.com
Fig. 1
Removable
Wrench End
Socket
Arrow
Indicates
Tightening
Direction
Pivot Point
Wrench
Body
Values on
Vertical
Scale
Handle
Scale (0 to 5)
Handle
Locking
Knob
Wrench Size and Arrow
Must Be
Same Side
Handle
Edge
BEFORE USE
• To retain wrench accuracy, DO NOT
LOOSEN nuts, bolts, etc. USE ONLY
FOR TIGHTENING.
• Apply a small amount of oil between handle and wrench body.
Note: If wrench is not used for an extended time, turn handle to lowest torque setting on wrench body. Rotate handle in both directions while making a few “clicks”. This re-lubricates the wrench.
INSTRUCTIONS
1.
Select Wrench from case.
2. Insert END into socket. Wrench size and arrow must be same side .
Fig. 1
3.
Loosen Locking Knob counterclockwise to unlock handle.
4. Select FOOT-Pound Scale Fig. 2 or
INCH-Pound scale Fig. 3
5.
Determine Proper Torque Setting
For Equipment Being Serviced
(use setting specified by equipment manufacturer).
6.
To obtain torque values ending in ‘0’, align (0) and Handle Edge with Torque Value On Vertical
Scale See Fig. 2 and Fig. 4 .
7. For torque values NOT ending in ‘0’, twist handle and align appropriate handle mark at handle edge with Torque Value On
Vertical Scale .
8. Tighten Locking Knob clockwise to lock in your torque setting.
9. Tighten Equipment Fitting, Bolt,
Nut Until Clicks Are Felt/Heard
From Pivot Point Note: To prevent tool damage, avoid further pressure on wrench after torque (clicks) achieved.
2
Fig. 2
Foot/Pound Scale (5-80) Inch/Pound Scale (60-960)
Fig. 3
Shown is 30 ft/lbs.
Center-line
Torque
Values
Handle Edge
Each mark on handle = ½ ft/lb
UP
DOWN
HANDLE
Each mark on handle
= 6 in/lb
Example 1: Set Wrench to 7 ft/lb a) Position wrench handle so Foot/Pound scale is visible.
b) Twist handle until “0” mark aligns with Center-line and 5 Foot/Pound torque value.
c) Twist handle RIGHT 4 detents (1 detent =
½ Foot/Pound) stopping at the “2” Mark on the Handle (while aligned VERTICALLY with the
Center-line). d) Final setting (5 + ½ + ½ + ½ + ½ = 7) e) Wrench is now set to 7 Foot/Pounds.
Example 2: Set Torque Wrench to
72 in/lb a) Position wrench handle so Inch/Pound scale is visible.
b) Twist handle until ‘0’ mark aligns with Center-line and 60 Inch/Pound torque value. c) Twist handle RIGHT 2 detents (2 detent = 12
Inch/Pound) stopping at first “1” mark on handle. d) Final setting (60 + 6 + 6 = 72) e) Wrench is now set at 72 Inch/Pounds.
5
5
5
5
5
+
0
+½ detent
+1 detent
+1 ½ detents
+2 detents
=
60
60
60
+
0
+ ½ detent
+1 detent
=
60
66
72
5
5.5
6
6.5
7
3
Fig. 4
FOOT/P
Ound
S eTTingS
On Wrench Body
65
70
75
80
45
50
55
60
25
30
35
40
5
10
15
20
H andle
S
S cale etting
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 inCH/P
Ound
S eTTingS
540
600
660
720
780
840
900
960
60
120
180
240
300
360
420
480
A
CCurACy
+/- 4%
(All Settings)
STORAGE
1. Loosen Locking Knob.
Turn Knurled Handle to lowest torque setting on Body Scale.
2. Remove Wrench End and place all components back in Storage Case.
3. Store kit in dry location.
REPLACEMENT PARTS
TLTWSAE
TLXTWSAE
SAE Multi-Head Torque
Wrench Set with handle, heads and case (
1 1 /
16
” , 1 5 /
16
” )
5 /
8
” , 11 /
16
” , 13 /
16
” , 15 /
16
” ,
5
Set of SAE Wrench Heads
/
8
” , 11 /
16
” , 13 /
Jaw Sizes
16
” , 15 /
16
” , 1 1 /
16
” , 1 5 /
16
”
TLXTWSAEW SAE Torque Wrench Handle
TLXTW58
TLXTW1116
5 /
8
”
11 /
16
Individual wrench head
” Individual wrench head
TLXTW1316
TLXTW1516
13 /
16
15 /
16
”
” Individual wrench head
Individual wrench head
TLXTW1L116 1 1 /
16
” Individual wrench head
TLXTW1L516 1 5 /
16
” Individual wrench head
LOCATIONS
CPS PRODUCTS, INC. U.S.A. (Headquarters)
1010 East 31st Street,
Hialeah, Florida 33013, USA
Tel: 305-687-4121,
1-800-277-3808
Fax: 305-687-3743
E-mail: [email protected]
Website: www.cpsproducts.com
CPS PRODUCTS CANADA LTD.
1324 Blundell Road
Mississauga, ON, L4Y 1M5
Tel: 905.615.8620, Fax: 905.615.9745
E-mail: [email protected]
Website: www.cpsproducts.com
CPS PRODUCTS N.V
Krijgsbaan 241, 2070
Zwijndrecht, Belgium
Tel: (323) 281 30 40,
E-mail: [email protected]
CPS AUSTRALIA PTY. LTD.
109 Welland Avenue,
Welland, South Australia 5007
Tel: +61 8 8340 7055,
E-mail: [email protected]
For the latest update(s) to these instructions, go to www.cpsproducts.com
#73-165 Rev. E
092617JA
advertisement
Related manuals
advertisement