Omcan 11067 Instruction Manual

Meat Grinder
Model MG-BR-0022
Item 11067
Instruction Manual
Revised - 09/23/2022
Toll Free: 1-800-465-0234
Fax: 905-607-0234
Email: [email protected]
www.omcan.com
Table of Contents
Model MG-BR-0022
Section
Page
General Information --------------------------------------------------------------------------- 3 - 4
Safety and Warranty --------------------------------------------------------------------------- 4 - 6
Technical Specifications -------------------------------------------------------------------------- 6
Installation -------------------------------------------------------------------------------------------- 7
Operation ----------------------------------------------------------------------------------------- 7 - 8
Maintenance ------------------------------------------------------------------------------------- 8 - 9
Parts Breakdown ---------------------------------------------------------------------------- 10 - 11
Electrical Schematics ---------------------------------------------------------------------------- 12
Notes ------------------------------------------------------------------------------------------- 13 - 14
Warranty Registration ---------------------------------------------------------------------------- 15
2
General Information
Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan
and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or
negligent use of this equipment. The product shall only be operated by someone over the age of 18, of
sound mind, and not under the influence of any drugs or alcohol, who has been trained in the correct
operation of this machine, and is wearing authorized, proper safety clothing. Any modification to the
machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of
the machine while in operation.
CHECK PACKAGE UPON ARRIVAL
Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the
external packaging, open carton to ensure all ordered items are within the box, and there is no concealed
damage to the machine. If the package has suffered rough handling, bumps or damage (visible or concealed),
please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may
initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be
filled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse
for damaged products that were shipped collect or third party.
Before operating any equipment, always read and familiarize yourself with all operation and safety
instructions.
Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save
these instructions for future reference. Also save the original box and packaging for shipping the
equipment if servicing or returning of the machine is required.
--------------------------------------------------------------------------------------------------------------------------------------------------Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et
Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne
ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de
plus de 18 ans, saine d’esprit, et pas sous l’influence d’une drogue ou d’acohol, qui a été formé pour
utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modification
de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine
ou des personnes à proximité de la machine pendant son fonctionnement.
VÉRIFIEZ LE COLIS DÈS RÉCEPTION
Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage
n’est visible sur l’emballage externe, ouvrez le carton afin de s’assurer que tous les éléments commandés
sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises
manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant
d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager
une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine
doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents
d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli
par un tiers transporteur.
3
General Information
Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations
et les consignes de sécurité.
Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces
instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour
l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.
--------------------------------------------------------------------------------------------------------------------------------------------------Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba
Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona
inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona
mayor de 18 años, en su sano juicio y no bajo alguna influencia de droga o alcohol, y que este ha sido
entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada.
Cualquier modificación a la máquina anúla la garantía y puede causar daños a las personas usando la
máquina mientras esta en el funcionamiento.
REVISE EL PAQUETE A SU LLEGADA
Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el
empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la
caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes
o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro
de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre
los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se
muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron
a recoger por terceros.
Antes de utilizar cualquier equipo, siempre leer y familiarizarse con todas las instrucciones de
operación y seguridad.
Omcan quisiera darles las gracias por la compra de esta máquina. Es de la máxima importancia para
guardar estas instrucciones para referencias en el futuro. También guarde la caja original y el embalaje
para envío del equipo si el mantenimiento o la devolución de la máquina es necesaria.
Safety and Warranty
GENERAL SAFETY REGULATIONS
This meat grinder is designed to grind meat products safely and efficiently. Unless the operator is properly
trained and supervised, however, there is the possibility of a serious injury. It is the responsibility of the owner
to ensure that this machine is used properly and safely, strictly following the instructions contained in this
manual and any requirements of local law.
4
Safety and Warranty
This machine can be potentially dangerous when used incorrectly. Therefore, read all the following instructions
carefully to avoid damage:
• Before cleaning, disconnect machine from power source.
• Always turn machine off in case of power supply lack.
• Provide enough space around machine to avoid breakings.
• Never use tools not belonging to machine to help operation.
• Never feed by hand; always use stomper.
• Never put your fingers or any other object but the stomper inside the feed throat.
• Never connect power source with wet hands or wet clothes.
• Never spray water or other liquid substances directly at motor, power switch, or any other electrical
components.
• Keep your working area clean and dry to prevent it from becoming slippery.
• Always install equipment in working area with adequate light and space away from children and visitors.
• Never operate without all warning labels attached and owner/operator manual available to operator.
• Never leave unattended while operating.
• Stop the machine immediately if you hear abnormal noises to prevent injuries.
• Never let dust or water get into electrical and mechanical comp machine.
• Always ground machine properly.
• Do not modify original features of the machine.
• Do not take out nor tear off any safety or identification label.
• Contact your distributor if you have any problems with the installation and operation of this machine.
RESIDENTIAL USERS: Vendor assumes no liability for parts or labor coverage for component failure
or other damages resulting from installation in non-commercial or residential applications. The right
is reserved to deny shipment for residential usage; if this occurs, you will be notified as soon as
possible.
1 YEAR PARTS AND LABOR BENCH WARRANTY
Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule a drop off to either
an Omcan authorized service depot in the area, or to an Omcan Service warehouse to repair the
equipment.
Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not
improper use.
Please see https://omcan.com/disclaimer for complete info.
5
Safety and Warranty
WARNING:
The packaging components are classified as normal solid urban waste and can therefore be disposed of
without difficulty.
In any case, for suitable recycling, we suggest disposing of the products separately (differentiated
waste) according to the current norms.
DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!
Technical Specifications
Model
Power
Throat
Motor RPM
Worm RPM
Electrical
Weight
Packaging Weight
Dimensions
Packaging Dimensions
Item Number
MG-BR-0022
2 HP / 1.5 kW
1.6” / 41mm
1750
150
110V / 60Hz / 1
89.8 lbs. / 40.7 kgs.
105 lbs. / 47.6 kgs.
28” x 13” x 24.8” / 711 x 330 x 629mm
21.5” x 33.5” x 22.5” / 546 x 851 x 572mm
11067
6
Installation
MAIN COMPONENTS
The machine consists of an electrical motor that, through a gear box, operates a worm. The worm feeds the
meat to the knife and hole plate. Several types of hole plates are available. The holes on these plates have
different diameter. The type of plate is chosen depending on
the desired ground meat characteristics.
The feed throat (No. 02; Figure 1) and worm (No. 03; Figure
2) receive an special treatment to isolate and facilitate the
cleaning.
The knife (No. 05; Figure 2) and disc (No. 06; Figure 2) are
made of hard material to provide a long life cutting quality.
INSTALLATION OF THE GRINDER
•
•
•
•
Figure 1
The meat grinder must be installed on a level, non-skid
surface with a maximum recommended height of 850 mm
by qualified or experienced people.
There should have a suitable space for the tray to collect
processed meat in front of the grinding device.
Check the voltage of the machine. The unit voltage must
be the same as the power source.
Grounding wire must always be connected.
01. Stomper
02. Feed Throat
03. Locking Ring
04. Tray
05. Motor Housing
06. ON/OFF Switch
Operation
PRE-OPERATION
•
•
•
•
•
•
Check if the machine is firm; no movement shall be allowed on the supporting surface.
It is recommended that the machine be carefully cleaned before first operation.
Clean the grinder as explained in the maintenance section.
After cleaning, reassemble the components in the following order: barrel, fiber washer, worm, worm pin,
knife, plates, and locking ring (See Figure 2).
Then check if all removable components are reassembled properly.
Turn locking ring (No. 07) counterclockwise until it applies a slight pressure on the hole plate and on the
knife.
NOTE: Do not tighten the locking ring too much, as an excessive pressure on the hole plate and knife may
lead to their abnormal wear.
7
Operation
01. Barrel
02. Fiber Washer
03. Worm
04. Worm Pin
05. Knife
06. Plates: 3 mm, 5 mm or 8 mm (optional)
07. Locking Ring
Figure 2
NOTE: Assemble the components following the order shown above (Figure 2). It is recommended that you
follow the order carefully. Assembling the components in a different order could cause serious damages to
the grinding device. When re-installing the knife in the worm stud, make sure that the cutting edge is facing
outwards.
After following the pre-operation instructions, your meat grinder is now ready to operate.
OPERATING THE MEAT GRINDER
1. Start the machine. This meat grinder is very high speed and, therefore, needs a fast feeding too.
2. Put the meat lumps on the tray.
3. Using the stomper (No. 01; Figure 1), push the meat into the feed throat where they will be sucked in by
the worm.
4. Feed meat at a constant rate for better grinding.
IMPORTANT: Only use the stomper to push the meat into the feed throat; never use your hands or any other
kind of instrument. It is strongly recommended that the meat chopper is not being operated without meat in
feed. Therefore, never let the machine to work without loading. If it happens, the temperature may rise as high
as 180°F in approximately 3 minutes, causing serious damages to the grinding components. Never leave any
kind of knives, metal hooks, or other instruments on the tray.
Maintenance
Clean the machine before first use and after use. To do the cleaning, proceed as follows:
• Turn off the machine and disconnect it from power source.
• Remove pusher (No. 01; Figure 1) and tray (No. 04; Figure 1).
• Remove Locking Ring (No. 03; Figure 1), turning it clockwise, and the internal components of the barrel,
8
Maintenance
pulling them out.
NOTE: Do not try to pull the plate, knife, and worm out off the barrel as this may result in serious injury to the
hands.
•
•
•
To remove the barrel, loosen the locking knob located on the left side of the barrel with both hands, and
move it to the left and right pulling it at the same time.
Proceed washing the components with warm water and neutral soap.
Wipe the body of the machine with a damp clean cloth.
9
Parts Breakdown
Model MG-BR-0022 11067
10
Parts Breakdown
Model MG-BR-0022 11067
Item No.
Description
Position
Item No.
Description
Position
Item No.
Description
Position
09892.2
AF906
Thermal Protector Label Ingles for 11067
33161.9
38388
PFS Sex UNC1/4x1 RTZB for 11067
00035.3
38572
Complete #22 Meat Grinding Head for
11067
38531
PCA Sex UNC 3/8 ZB for 11067
00108.2
38581
Motor Gear for 11067
13831.2
AF907
Attention Ear Wire Label Ingles/Frances
for 11067
33170.8
30258
Washer L 5/16 ZB for 11067
00119.8
30047
Nut M4 DIN 934 for 11067
14175.5
67041
Key 40127 A2E3Q-NA KEMA for 11067
33172.4
27688
Clamp K22 (T 50R) for 11067
00210.0
21842
Fiber Gear for 11067
14791.5
AF908
Attention Warning Label for 11067
33303.4
38548
Throat Set N°22 for 11067
00550.9
AH534
Eng. Box W/Pin (Hammed C.) for 11067
14812.1
AH538
English/French Danger Label for 11067
33306.9
21843
Ball Bearing 6001 for 11067
00738.2
30050
Terminal Cover for 11067
17582.0
AF910
Warning Label Ingl./Franc. for 11067
33307.7
AE670
Term. Eyelet for 11067
01137.1
38528
Term.Positiv Lock 2 A 4 for 11067
17628.1
AH539
PE Extensioner for 11067
35561.5
38545
Blades for Meat Grinders for 11067
01657.8
38542
Copper Tube for 11067
19566.9
AH540
PCA M6 Special ZB for 11067
35614.0
38518
Machine Plate 3” Dia for 11067
01658.6
38590
Lid Coupling Connection for 11067
19567.7
AH541
PCA M4 Special ZB for 11067
35615.8
38546
Disc 5mm Nº22 for 11067
01659.4
38541
Meat Mincer Stable for 11067
19568.5
AH542
Certified Base (Gray) for 11067
35632.8
16401
Retainer Seal 00784BR1(F.0122) for
11067
01741.8
38539
Gear Box Lid (C.Martel.) for 11067
19647.9
AH543
2CV 60Hz W Engine with Thermal
Protector for 11067
35706.5
21844
Worm Gear for 11067
02720.0
38593
Screw M5x6 DIN 84 Stainless Steel
for 11067
22996.2
AH544
Socket NO.22 Certificate for 11067
35732.4
38534
PFS M8x25 DIN 933 ZB for 11067
02728.6
38412
PFS M4x5 DIN 7985 INOX for 11067
23932.1
AH545
CB.3x5.3mm2 SJX2M Certif. for 11067
35739.1
38393
Screw Nut M3 DIN 934 ZB for 11067
03088.0
38177
PFS M10x12 DIN 933 ZB for 11067
24548.8
AH546
Wire EL.Flex.5.3x300mm Cert. for 11067
35784.7
25078.3
AH547
Wire EL.Flex.5.3x670mm Cert. for 11067
35785.5
AH532
PFS M4x16 DIN 7985 ZB for 11067
03139.9
AH535
Cont.CWM32-00-30D13 110V 50/60Hz
for 11067
27695
Allen Screw M6x8 for 11067
03188.7
27720
Omcan Logo (Machines) for 11067
27154.3
AH548
Cable Press PG21 Black6PCA W/
Red.9A14 for 11067
37229.3
38395
PFS M8x10 DIN 933 ZB for 11067
03196.8
30059
Omcan Packaging Logo for 11067
27155.1
AH549
American Plug Certif.30A 125V 4A262
for 11067
37843.7
38530
PFS Sex UNC3/8x2.3/4 RPZB for 11067
03214.0
AH536
Micro Drive Pin for 11067
28237.5
AH550
Warning Label for 11067
38110.1
27696
Nylon Cover CN 4478 for 11067
03678.1
AF901
Shutter 25x5x100 for 11067
29260.5
AH551
CS Tray Support for 11067
39111.5
29340.7
AH552
CS Certified Cabinet for 11067
39415.7
27699
Cramp T 18R Small for 11067
04203.0
67037
Foot Bor.Red.C/PFS M10x30
D.50x34x30 ALT for 11067
30038
Screw M3x6 DIN 84 ZB for 11067
04208.0
AE677
Key W / Prot.30223 M2FT2FE3V / 19
for 11067
30565.0
AH553
Certified Back Cover 1.5CV for 11067
39419.0
21578
Knob with Bar M10x30mm for 11067
04511.0
AH537
Micro Support for 11067
30786.6
AH554
Completed Cabinet Certificate for 11067
39967.1
38523
Rubber Cover for 11067
05065.2
67038
Grounded Wire Label for 11067
31140.5
AH555
Spanish/English Fragile Label for 11067
41966.4
21577
Oil Cap PSN/EE-CMSE for 11067
08900.1
AF905
Thermal Protector Protection for 11067
32629.1
AH556
Mouth Fixation Label for 11067
67136.3
AH533
PFS M3x16 DIN 7985 ZB for 11067
09093.0
67040
Instruction Manual Label for 11067
32832.4
AH557
CS Tray No.22 Cert. for 11067
69620.0
11
Electrical Schematics
Model MG-BR-0022 11067
12
Notes
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
13
Notes
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
14
Warranty Registration
Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at
the perforation and then send to the address specified below. You can also register online by visiting:
Merci d’avoir acheté un produit Omcan. Pour enregistrer votre garantie pour ce produit, complétez les informations ci-dessous, détachez la
carte au niveau de la perforation, puis l’envoyer à l’adresse spécifié ci-dessous. Vous pouvez également vous inscrire en ligne en visitant:
Gracias por comprar un producto Omcan usted. Para registrar su garantía para este producto, complete la información a continuación,
cortar la tarjeta en la perforación y luego enviarlo a la dirección indicada a continuación. También puede registrarse en línea en:
https://omcan.com/warranty-registration/
For mailing in Canada
For mailing in the US
Pour postale au Canada
Pour diffusion aux États-Unis
Por correo en Canadá
Por correo en los EE.UU.
OMCAN
OMCAN
PRODUCT WARRANTY REGISTRATION
3115 Pepper Mill Court,
Mississauga, Ontario
PRODUCT WARRANTY REGISTRATION
4450 Witmer Industrial Estates, Unit 4,
Niagara Falls, New York
Canada, L5L 4X5
USA, 14305
or email to: [email protected]

Purchaser’s Information
Name:
Company Name:
Address:
Telephone:
City:
Province or State:
Postal or Zip:
Country:
Email Address:
Type of Company:
Dealer from which Purchased:
Dealer City:
Dealer Province or State:
Restaurant
Bakery
Deli
Butcher
Supermarket
Caterer
Institution (specify):
Invoice:
Other (specify):
Model Name:
Model Number:
Serial Number:
Machine Description:
Date of Purchase (MM/DD/YYYY):
Would you like to extend the warranty?
Date of Installation (MM/DD/YYYY):
Yes
No
Thank you for choosing Omcan | Merci d’avoir choisi Omcan | Gracias por elegir Omcan
15
Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North
American food service industry. Our success over these many years can be attributed to our commitment
to strengthen and develop new and existing relationships with our valued customers and manufacturers.
Today with partners in North America, Europe, Asia and South America, we continually work to improve
and grow the company. We strive to offer customers exceptional value through our qualified local sales
and service representatives who provide convenient access to over 6,500 globally sourced products.
Depuis 1951 Omcan a grandi pour devenir un des “leaders” de la distribution des équipements et
matériel pour l’industrie des services alimentaires en Amérique du Nord. Notre succès au cours de ces
nombreuses années peut être attribué à notre engagement à renforcer et à développer de nouvelles
et existantes relations avec nos clients et les fabricants de valeur. Aujourd’hui avec des partenaires en
Amérique du Nord, Europe, Asie et Amérique du Sud, nous travaillons continuellement à améliorer et
développer l’entreprise. Nous nous efforçons d’offrir à nos clients une valeur exceptionnelle grâce à
nos ventes locales qualifiées et des représentants de service qui offrent un accès facile à plus de 6500
produits provenant du monde entier.
Desde 1951 Omcan ha crecido hasta convertirse en un líder en la distribución de equipos y suministros
de alimentos en América del Norte industria de servicios. Nuestro éxito en estos años se puede atribuir
a nuestro compromiso de fortalecer y desarrollar nuevas relaciones existentes con nuestros valiosos
clientes y fabricantes. Hoy con socios de América del Norte, Europa, Asia y América del Sur, que trabajan
continuamente para mejorar y crecer la empresa. Nos esforzamos por ofrecer a nuestros clientes valor
excepcional a través de nuestro local de ventas y representantes de los servicios que proporcionan un
fácil acceso a más de 6,500 productos con origen a nivel mundial.