hattrick STYLE M Operating Instructions Manual

HATTRICK STYLE M MOTORIZED TREADMILL
OPERATING INSTRUCTIONS MANUAL
1
IMPORTANT SAFEGUARDS
Read all instructions carefully before using this product. Keep this owner’s manual for further reference:
CAUTION
Exercise of a strenuous nature, as is customarily done on this equipment should not be undertaken
without first consulting a physician.
No specific health claims are made or implied as they relate to the equipment.
1. It is the responsibility of the owner to be sure that all users of this treadmill are informed of all
warnings and precautions.
2. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a garage or
covered patio, outdoors or near water.
3. Keep pets and small children away from the treadmill at all times.
4. Never start the treadmill while you are standing on the walking belt.
5. Always hold the handrails while using the treadmill.
6. The treadmill is capable of high speeds. To avoid sudden jumps in speed, adjust the speed in small
increments.
7. Regularly inspect and tighten all parts of the treadmill. Keep hands away from all moving parts.
8. When folding or moving the treadmill, make sure that the safety lock is fully engaged. Please refer
to the folding instructions pages of this manual for safety lock operation.
9. Always unplug the power cord before performing the maintenance and adjustment procedures
described in this manual. Do not remove the motor cover unless instructed to do so by an
authorized service representative. Servicing other than the procedures in this manual should be
performed by an authorized service representative only.
10. Keep all electrical components, such as the motor and power cord away from water or other liquids
to prevent shock. Do not set anything on the handrail, computer console or belt. Never place liquids
on any part of the unit.
11. Always insert the safety key and attach the clip to your clothing at your waist before beginning your
workout. If you encounter problems and need to stop the console quickly, simply pull on the cord to
disengage the safety key from the console. To continue operation, simply put the safety key on the
console.
12. Remove the safety key and store it away in a safe place when the treadmill is not in use. Keep the
safety key away from children.
13. Wear the proper exercise clothing and shoes for your workout. Do not ware loose clothing or shoes
with leather soles or heels. Be sure to tie long hair back.
14. Keep all loose clothing and towels away from running surface. The belt will not stop immediately if
an object becomes caught in the rollers or belt. If an object become caught, turn the unit off
immediately.
15. Proceed with caution when getting on or off the treadmill. Use the handrails whenever possible.
Only step onto the running surface when the treadmill is running at a very low speed. Do not step
off the treadmill while the belt is moving.
16. To get on or off the running surface, straddle the running surface by standing on the side rails. Use
this procedure before starting the belt (to begin your workout ) and after it has stopped (at the end
2
of your workout).
17. Never attempt to turn around while on the running belt. Keep your head and body facing forward at
all times.
18. Never turn on the treadmill while someone is standing on the running surface.
19. Be careful not to over exert yourself during your workout, stop your workout immediately if you feel
any pain or discomfort. Consult your physician immediately.
20. Do not modify or attempt any service on the treadmill yourself other than assembly and
maintenance described in this manual.
21. The treadmill should not be operated for more then 45-50 min in a stretch.
3
ASSEMBLY INSTRUCTIONS
When you open the carton, you will find the below spare parts:
Spare parts list:
NO.
DES.
1
MAIN FRAME
96
NO.
DES.
Specification
Nos.
1
66
LOCK NUT
8
6
CONNECTING FRAME
1
69
SPRING WASHER
8
9
97
SUPPORTING FRAME
1
68
FLAT WASHER
8
9
101
MASSAGE HEAD
1
47
BOLT
M8*25 L20
6
102
MASSAGE BELT
1
48
BOLT
M8*40 L20
2
46
BOLT
M8*10
3
100
ARC WASHER
￠8
9
14
BOLT
M8*15
10
45
NUT
M8
2
1
12
5mm
1
11
Specification Nos.
WRENCH W/SCREW
S=13、14、15
DRIVER
5#ALLEN WRENCH
FIXING TOOLS:
5#ALLEN WRENCH 5mm
1pcs、
WRENCH W/SCREW DRIVER S=13、14、15
1pcs
Notice: Do not connect to power source before assembly is completed
4
ASSEMBLY STEP ONE：
Open the carton， take out the above
spare parts，put the MAIN FRAME on the
ground.
ASSEMBLY STEP TWO:
Pull up the display and upright as arrow
direction.
Notice: When you pull up display, make
sure the upright not press the wires in
upright; keep touch the upright and
display by hand, that they will not fall
down escaping any hurt.
ASSEMBLY STEP THREE:
Use the 5# allen wrench, drill through the
bolt (46) to lock washer(66), then lock
the Left upright (3) onto MAIN FRAME
(1)
Notice: Support the Left upright with
hand, avoid falling down to cause any
hurt.
5
ASSEMBLY STEP FOUR:
Use the 5# allen wrench, drill through
the bolt (46) to lock washer(66), then
lock the Right upright (4) onto MAIN
FRAME (1)
ASSEMBLY STEP FIVE:
Use the 5# allen wrench, drill through
the bolt (46) to lock washer(66), then
lock the COMPUTER (64) onto R&L
upright (3,4).
ASSEMBLY STEP SIX:
1.Use 5# Allen Wrench，drill the bolt
M8*25(47) through the flat washer
8 (69), spring washer 8 (68), then
lock the connecting frame (96) onto
the left&right upright tube(3,4)
6
ASSEMBLY STEP SEVEN:
1.Use 5# Allen Wrench ， drill the
bolt M8*25(47) through the flat
washer 8 (68), spring washer 8
(69), then lock the supporting
frame (97) onto the main frame
(1);
2. Use 5# Allen Wrench, drill the
bolt M8*40(48) through the arc
washer (100), nut(45), lock the
supporting
frame
onto
the
connecting frame .
ASSEMBLY STEP EIGHT:
1. Use 5# Allen Wrench, drill Bolt
M8*15 (14) through the spring
washer (68), flat washer (69), lock
the massage head (101) onto the
supporting frame (97)
2. Hang the massage belt (102)
onto the massage head (101)
ATTENTION：must confirm complete assembly as the require above and
lock all the bolt. Do the following operation after checking everything is OK.
Before you use the treadmill, please read the instruction carefully.
7
FOLDING INSTRUCTION
Pulling up:
A
Support the rear roller A with hand, then
pull up the running deck, till hearing the
sound that the cylinder B is locked into
the round tube
B
Pulling down:
A
Support the rear roller A with hand ,
depress the air pressure control bar B,
then the base frame will fall down
automaticlly
B
8
TECHNICAL PARAMETER
BUILT UP SIZE(mm)
1750*715*1315
FOLDABLE SIZE(mm)
1040*715*1470
RUNNING
SURFACE
SIZE(mm)
MAX WEIGHT
DISPLAY
1250*450
POWER
MAX OUTPUT
POWER
See product specs
See product specs
INPUT CURRENT
See product specs
SPEED RANGE
1.0-18KM/h
130KG
SPEED、 TIME 、DISTANCE、INCLINE、 CALORIES、 PULSE
This product must be grounded. If it should malfunction or breakdown, grounding provides
a path of least resistance for electric current to reduce the risk of electric shock. This
product is equipped with a cord having an equipment-grounding conductor and a
grounding plug. The plug must be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes and ordinances.
DANGER – Improper connection of the equipment-grounding conductor can result in
a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt
as to whether the product is properly grounded. Do not modify the plug provided with the
product – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
This product is for use on a nominal voltage circuit and has a grounding plug that
looks like the plug illustrated in sketch A in following figure. Pleaase ensure that the product is
connected to an outlet having the same configuration as the plug. No adapter should be
used with this product.
9
OPERATION GUIDE
WINDOW DISPLAY:
1.“SPEED” window:Display speed, show range: 1.0-18KM/h.
2.“INCL” window：Show the incline, the incline range is 0-20 level;
3、“TIME” window:Show the running time, count from 0:00 to 99:59. When up to 99:59,
the machine will stop smoothly and show ‘END’ in the computer; When you set the time count down, it
will count down from the setting data to 0, when down to 0:00, the machine will stop smoothly and
show ‘END’ in the computer.
4、“DIS”window: Show running distance，count from 0.00 to 99.9, when up to 99.9, the machine will
clear the data, and recount from 0; When you set the distance count down, it will count from the
setting data to 0. when down to 0, the machine will stop smoothly and show ‘END’ in the computer,
after 5 seconds, the machine will be in the default state.
5、“CAL /PULSE” window: Display runner calories and pulse. When show calories, count from 0 to 999,
to 999 will spill over to clear 0; when calories count down, it will count down from setting data to 0, then
the machine will stop smoothly and show ‘End’, enter the beginning state after 5 seconds. When
runner grasps the hand pulse, it will test pulse after 5 seconds and show the data in window, the
relevant direct light will show at the same time, pulse range is 40 to 200 hypo/min ( the data is just for
reference, can not be as medicinal data.
10
BUTTON FUNCTION:
1. “PROGRAM” Button：When the treadmill is not running, press the button can circle choose and
set up the exercise time and program from “0：00” “ P1-------P5--------P10-------P15-------P24FAT”.
Manual mode is the default program, the default speed in kilometer is 1KM/H. (0:00 is manual
mode,pre-set program :P1-P25)
2. “MODE” Button：Press this button to choose circle modes: “0：00” “15：00”、“1.0”、“50” (“0：00” is
manual model, “15：00” is the time count down, “1.0” is distance count down and “50” calorie count
down); when you choose every mode,you can press the speed button and incline button to set
count,after that ,press the START button to start this treadmill.
3．“START”button：when start the power and attach the magnet end of the safety pulling rope to the
computer. Press the button at any time, it can start motor.
4. “STOP”button: press this button while running,it can stop motor and set program default;
5. “SPEED+”、“SPEED-” Button：set default count;to adjust speed when treadmill start,the scope is
0.1km/hypo in kilometer. Press the button more than 0.5 seconds,will be up or down duratively.
6. “INCLINE+”、“INCLINE-” Button: set the default incline; to adjust incline when treadmill start, the
scope is 1 section;
START-UP QUICKLY(MANUAL)
1. Open the power switch, attach the magnet end of the safety pulling rope to the computer.
2. Press STATR/STOP button，the system will enter into 3 seconds count down, the buzzer will make
sound and the time window display count down, the speed will run 1.0km/hour after 3 seconds.
3. After start-up, you can use “SPEED+”、 “SPEED -” to adjust the speed up or down; use “INCLINE+”、
“INCLINE -” to adjust the incline up or down.
THE OPERATION OF EXERCISE PROCESS:
1. Press speed-down will reduce the running speed.
2. Press speed-up will increase the running speed.
3. Press incline down will reduce the incline section.
4. Press incline up will increase the incline section.
5. Press STOP will reduce until it stopped.
6. When the user hold the hand pulse by both hand, the computer will show the user’s pulse data after
5 seconds
MANUAL MODE:
1. If you do not make any setting and press START button directly, the treadmill will start to run from
the speed 1.0km/h, incline 0. The other windows will start to count from positive direction from windows
11
default, press “SPEED+”, “SPEED-” change the speed, press “INCLINE+”、“INCLINE -”to change the
incline;
2. set up the Time, press “MODE” button to enter into time count down, the TIME window will
display“15：00” and glittering. Press “SPEED+”, “SPEED-” , “INCLINE+”、 “INCLINE –“ to set up the
time what you need. The setting range is 5:00-99:00.
3.In Time setting model, press “ MODE “ button to enter into distance count down, the DISTANCE
window will display “1.0” and glittering. Press “SPEED+”, “SPEED-”, “INCLINE+”、 “INCLINE –“ to set
up the distance what you need. The setting range is 0.5—99.9.
4、To set up the Calories, press “MODE” button to enter into calories count down, the CAL window will
display “50’ and glittering. Press “SPEED+”, “SPEED-” , “INCLINE+”、 “INCLINE –“ to set up the
calories what you need. The setting range is 10-999.
5、When setting is finished, press “START” button to start up, the treadmill will run after 3 seconds,
press “SPEED+”, “SPEED-”, “INCLINE+”、 “INCLINE –“ to adjust the speed and the incline; press
the STOP, the treadmill will stop.
INNER INSTALL PROGRAM
Press “PROGRAM” button SPEED window will display P1-P24 to choose the program you like. Setting
of running time, then the TIME window display glittering. Display the advance setting time10:00, press
“SPEED+”, “SPEED-”, “INCLINE+”、 “INCLINE –“ to set up the exercise time what you need. Press
“START” button to start the inner install program, the inner install program is divided into 10 sect. Each
exercise time=the setting time/10. When the system enter into the next sect will make 3 sound
“B—B—“ and the speed will be changed according to the setting program, then press
“SPEED+”,
“SPEED-”, “INCLINE+”、 “INCLINE –“ to change the SPEED and INCLINE, When the program enter
next sect will come back to the current speed and incline, and run the one program, the system will
make 3 sound “B—B—“ and change to the manual program automatically.
PROGRAM EXERCISE CHART
Each program will divide into 10 grades for the exercise time and each time section has the speed and
incline accordingly.
Time
TIME INTERVAL
Mode
1
2
3
4
5
6
7
8
9
10
SPEED
2
4
3
4
3
5
4
2
5
3
INCLINE
1
2
3
3
1
2
2
3
2
2
SPEED
2
5
4
6
4
6
4
2
4
2
P1
P2
12
INCLINE
1
2
3
3
2
2
3
4
2
2
SPEED
2
5
4
5
4
5
4
2
3
2
INCLINE
1
2
2
3
1
2
2
2
2
1
SPEED
3
6
7
5
8
5
9
6
4
3
INCLINE
2
2
3
3
2
2
4
6
2
2
SPEED
3
6
7
5
8
6
7
6
4
3
INCLINE
1
2
4
3
2
2
4
5
2
1
SPEED
2
8
6
4
5
9
7
5
4
3
INCLINE
2
2
6
2
3
4
2
2
2
1
SPEED
2
6
7
4
4
7
4
2
4
2
INCLINE
4
5
6
6
9
9
10
12
6
3
SPEED
2
4
6
8
7
8
6
2
3
2
INCLINE
3
5
4
4
3
4
4
3
3
2
SPEED
2
4
5
5
6
5
6
3
3
2
INCLINE
3
5
3
4
2
3
4
2
3
2
SPEED
2
3
5
3
3
5
3
6
3
3
INCLINE
4
4
3
6
7
8
8
6
3
3
SPEED
2
5
8
10
6
9
5
3
2
2
INCLINE
1
3
5
8
10
7
6
3
2
3
SPEED
2
5
5
4
4
6
4
2
3
4
INCLINE
3
5
6
7
12
9
11
11
6
3
2
7
4
7
8
9
4
5
3
2
5
6
6
4
6
5
8
9
4
2
2
6
5
4
8
6
5
2
3
3
5
6
5
8
4
5
5
10
6
3
2
6
5
4
8
7
5
3
3
2
3
4
5
6
3
5
5
6
4
3
2
5
7
5
8
6
5
2
4
2
1
5
6
8
12
9
10
9
5
3
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
SPEED
P13
INCLINE
SPEED
P14
INCLINE
SPEED
P15
INCLINE
SPEED
P16
INCLINE
13
SPEED
P17
INCLINE
SPEED
P18
INCLINE
SPEED
P19
INCLINE
SPEED
P20
INCLINE
SPEED
P21
INCLINE
SPEED
P22
INCLINE
SPEED
P23
INCLINE
SPEED
P24
INCLINE
2
5
6
7
8
9
10
5
3
4
3
5
6
8
6
5
8
7
5
3
2
3
5
6
8
6
9
6
5
2
5
7
5
8
6
5
9
10
6
2
3
7
6
5
9
7
6
3
5
2
3
5
6
8
5
6
5
12
8
3
3
7
9
10
11
12
10
8
5
2
2
5
6
7
6
5
8
6
3
2
3
6
8
7
9
10
5
8
3
2
3
6
8
9
9
6
8
10
6
3
3
5
8
6
9
10
8
12
6
3
2
6
8
10
12
10
12
8
5
2
3
5
9
11
12
8
6
5
3
2
2
6
8
10
9
7
8
10
6
3
3
8
10
11
12
10
10
8
5
3
3
6
8
9
10
12
9
6
3
2
RANGE OF PROGRAM
PROGRAM
BEGIN
SET UP RANGE
DISPLAY RANGE
TIME(MIN:SECOND)
0:00
15:00
5:00-99:00
0:00－99:59
INCLINE(LEVEL)
0
0
0-20
0-20
1.0-18
1.0-18
SPEED(K/h)
1.0
1.0
DISTANCE(K)
0
1.0
0.5-99.9
0.00－99.9
PULSE(hypo/min)
P
N/A
N/A
50-200
CALORIE(THERM)
0
50
10-999
0－999
BODY TESTER:
At the beginning state, press “ PROGRAM” continuely entering FAT body fat tester, press “ MODE
“ enter F-1、F-2、F-3、F-4、F-5 ( F-1 SEX, F-2 AGE, F-3 HEIGHT, F-4 WEIGHT, F-5 FAT TESTER ),
14
Press “SPEED+”、“SPEED -” to set F-1 – F4 ( refer to the following chart), after that, press “ MODE” to
set F-5, grasp the hand pulse, the window will display your body quality index after 3 seconds. The
body quality index is to test the relation between height and weight. The body FAT suits for any male
and female, to adjust the weight according it together with other body quality index. The idea FAT
should be 20-25, if under 19, it means too thin. If between 25 and 29, it means overweight, if over 30, it
means obesity. ( The data is just for reference, can not be as medicinal data)
F-1
F-2
Seg
Age
F-3
F-4
Hight
Weight
01 male
100----200
20-----150
≤ 19
=(20---25)
=(26---29)
FAT
F-5
02 female
10------99
FAT
FAT
FAT
≥ 30
Underweight
Normalweight
Overweight
Obesity
SAFETY LOCK FUNCTION:
Pull out the safety pulling rope, then the treadmill will stop immediately. All the windows
display“―――”，the buzzer will make 3 sound “B—B—”,now the treadmill must be stop. Attach the
magnet end of the safety pulling rope to the computer, the treadmill will be at the beginning of running.
SAVE ON POWER FUNCTION:
The system is with saving on power function, at the state of waiting for operation, if without any
operation, the saving on power function will be available after 10 mins, the display will be closed up.
You can press any button to turn on the display.
MP3 FUNCTION
When the power is on, contacting the external MP3 equipment, the computer will play. The voice is
adjustable from operate the external MP3 equipment, the voice should be adjusted on the proper
section to protect the computer loudhailer.
CLOSE UP:
Switch off the power: You can switch off the power to stop the treadmill, which won’t be damaged at any
time.
CAUTION:
1. We recommend that you maintain a slow speed at the beginning of a session and hold on to the
handrails until you become comfortable and familiar with the treadmill.
2. Attach the magnet end of the safety pulling rope to the computer and also attach the clip of the
safety pulling rope to your clothing.
15
3. To end your workout safely, press the STOP button or pull out the safety pulling rope, then the
treadmill will stop immediately.
EXERCISE INSTRUCTIONS
1. The Warm Up Phase
This stage helps get the blood flowing around the body and the muscles working properly. It will also
reduce the risk of cramp and muscle injury. It is advisable to do a few stretching exercises as shown
below. Each stretch should be held and count to approximately 30 seconds, do not force or jerk your
muscles into a stretch - if it hurts, STOP.
2. The Exercise Phase
This is the stage where you put the effort in. After regular use , the muscles in your legs will
become Stronger. Work to you but it is very important to maintain a steady tempo throughout. The rate
of work should be sufficient to raise your heart beat into the target zone shown on the graph below.
16
This stage should last for a minimum of 12 minutes although most people
start at about 15-20 minutes
3. The Cool Down Phase
This stage is to let your Cardio-vascular System and muscles wind down. This is a repeat of the
warm up exercise e.g. reduce your tempo, continue for approximately 5 minutes. The stretching
exercises should now be repeated, again remembering not to force or jerk your muscles into the
stretch.
As you get fitter you may need to train longer and harder. It is advisable to train at least three times a
week, and if possible space your workouts evenly throughout the week
To tone muscle while on your treadmill you will need to have the resistance set quite high. This will
put more strain on our leg muscles and may mean you cannot train for as long as you would like. If you
are also trying to improve your fitness you need to alter your training program. You should train as
normal during the warm up and cool down phases, but towards the end of the exercise phase you
should increase resistance, making your legs work harder than normal. You may have to reduce your
speed to keep your heart rate in the target zone.
The important factor here is the amount of effort you put in. The harder and longer you work the more
calories you will burn. Effectively this is the same as if you were training to improve your fitness, the
difference is the goal.
MAINTENANCE INSTRUCTIONS
WALKING BELT CENTERING AND TENSION ADJUSTMENT
DO NOT OVERTIGHTEN the walking belt. This may cause reduced motor performance and excessive
roller wear.
17
TO CENTER WALKING BELT:
● Place treadmill on a level surface
● Run treadmill at approximately 3.5 mph
● If the belt has drifted to the right, turn the right adjusting bolt 1/2 turn clockwise and the left adjusting
bolt 1/2 turn counterclockwise
● If the belt has drifted to the left, turn the left adjusting bolt 1/2 turn clockwise and the right adjusting
bolt 1/2 turn clockwise and the right adjusting bolt 1/2 turn counterclockwise
PIC A
Picture A If the belts has drifted to the RIGHT
PIC B
Picture B If the belts has drifted to the LEFT
WARNING: ALWAYS UNPLUG THE TREADMILL FROM THE ELECTRICAL OUTLET BEFORE
CLEANING OR SERVICING THE UNIT.
CLEANING
General cleaning or the unit will greatly prolong the treadmill.Keep treadmill clean by dusting regularly.
Be sure to clean the exposed part of the deck on either side of the walking belt and also the side rails.
This reduces the build up of foreign material underneath the walking belt.
The top of the belt may be cleaned with a wet, soapy cloth. Be careful to keep liquid away from inside
the motorized treadmill frame or from underneath the belt. Warning：Always unplug the treadmill
from the electrical outlet before removing the motor cover. At least once a year remove the motor
cover and vacuum under the motor cover.
18
WALKING BELT AND DECK LUBRICATION
This treadmill is equipped with a pre-lubricated, low maintenance deck system. The belt/
deck friction may play a major role in the function and life of your treadmill, thus requiring
periodic lubrication. We recommend a periodic inspection of the deck.
We recommend lubrication of the deck according to the following timetable:
a) Light user (less than 3 hours/ week)
triweekly
b) Medium user (3-5 hours/ week)
fortnightly
c) Heavy user (more than 5 hours/ week)
once a week
EXPLODED DRAWING
19
PARTS LIST
No.
Description
1
Base frame
Specification
Q’ty
No.
1
38
Description
Left speaker cover
1
4
2
Main frame
1
39
Right speaker cover
3
Left upright
1
40
Handpulse plate
4
Right Upright
1
41
Nut
5
Computer Bracket
1
42
EVA Pad
6
Motor Bracket
1
43
7
Fixing pin
2
44
Screw
Nut
8
9
10
Turnning Bushing
Front roller
Rear roller
2
1
1
45
46
47
20
Nut
Screw
Screw
Specification
Q’ty
1
M3
4
2
M8*30
4
M6
8
M8
8
M8*10
12
M8*25
3
11
12
13
Wrench w/ screw
driver
5# Allen Wrench
Screw
S=13、14、15
5mm
Cyliner
1
48
1
49
1
50
14
15
16
17
18
51
Motor top cover
Motor bottom
cover
Console top cover
Console inner
cover
1
52
1
53
1
54
Screw
Screw
Bolt
Screw
Screw
M8*40, 20
3
M8*45, 20
2
M10*55
2
M6*55
3
M8*35
5
M6*35
8
M3*8
2
M5*16
4
M5*8
7
Screw
1
55
19
Console controller
1
56
20
Left rear cover
1
57
21
Right rear cover
1
58
22
Screw
Magnetic sensor
Screw
Screw
1
ST2.9*6.5
19
ST4.2*12
15
ST4.0*20
2
2
23
Side rail
Motor bottom
cover
1
60
24
Running belt
1
61
Screw
ST2.9*8
2
25
Left speaker net
1
62
Bolt
M8*30
2
26
Wheel cover
2
63
Screw
ST4.2*12
18
27
Motor belt
1
64
Adaptor
28
Blue cushion pad
4
65
Washer
6
3
29
Black cushion pad
4
66
Washer
16
30
Moving wheel
2
67
31
Foot pad
2
68
Washer
Screw
8
M3*32
8
6
32
Right speaker net
Ring protecting
wire plug
1
69
Washer
8
6
2
70
Console controller
33
34
35
36
37
75
76
77
78
79
80
81
Power wire buckle
Handpulse panel
Round plug
Foam
Power wire
Square switch
Overload
Protecter
AC wire
AC wire
AC wire
DC motor
82
83
84
Running board
Magnetic core
Magnetic ring
59
Screw
Screw
Brown120
Blue 150
Brown 150
1
4
2
2
1
1
71
72
73
74
91
92
Controller
Quick start/stop button
Quick speed button
Safety accessory
Plain washer
Incline motor
1
1
1
1
1
93
94
95
97
96
bolt
bolt
washer
Supporting frame
Conecting frane
1
1
1
98
99
101
21
Foam handle bar
φ50*φ17*145
1
4
1
10
M10*30
M10*50
10
1
1
1
1
2
1
1
1
2
1
1
Drain cap
4
4
Massage head
1
85
86
87
88
89
90
bolt
Speaker
Amplifier board
Screw
Screw
MP3 wire
ST4.2*12(option)
ST2.9*6.5(option)
option
8
2
1
4
4
1
102
Massage belt
1
TROUBLESHOOTING GUIDE
1、Probable reason for computer not workable after power start: The wire from computer to bottom
control board didn’t connected well or the transformer was burnt out. Check the each wire from
computer to control board, make sure they are connected well. If the wire is destroyed , change it. If the
above can not settle the problem, try to change a good transformer.
2、E01: Message failure. Probable reason: The wires from computer and bottom control board did not
connect well, please check each wire. If the wire was destroyed, change a good one.
3、E02: Burst clash. Check the power is right, if not, use correct power to test; Check if the bottom
22
control was burnt out, change a good one; reconnect the motor wire.
4、E03: No sensor signal. Sensor wire badness, change good wire; It is no use for the motor magnetic,
change the magnetic or reset the magnetic;
5.E04: Incline learning defeated, Check VR wire of incline motor whether connect well. If not, reconnect
VR to make it firm; Check AC wire of motor whether connect well, and AC wire of motor whether insert
well with correct sign of control board; Check connection line of motor whether is destroyed, exchange
it or incline motor. And press “learning” botton of bottom control board to relearn after checked
everything is well.
6、E05: Current overload protecting. Over rated loaded or the motor is stuck, cause excessive current,
machine will start self-protecting system. Adjust the machine and restart; Check if the motor has noise
from motor or if the motor / bottom control board were burnt out, if burnt out, change good motor and
bottom control; Use right voltage.
7、If the motor can not work after pressing START button, the probable reason: the motor wire is broken;
the safety pipe is broken or fell; motor wire is not conneted well; IGBT on bottom control board is
burnt out. Test the above reasons and change the relevant part.
23
">