advertisement
PCM
-2811
PC/104 VGA/LCD Module
User’s Manual
(Version 1.0)
Copyright Notice
This document is copyrighted, 2002 by the manufacturer.
All rights are reserved. The information in the manual is subject to change without notice in order to improving products.
No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of the manufacturer.
The manufacturer
assumes no responsibility for any inaccuracies that may be contained in this document. The manufacturer
makes no commitment to update or to keep current the information contained in this manual.
Copyright 2002
All rights reserved. Ver.1.0 2002,
Printed in Taiwan
Trademarks Acknowledgments
All brand names and trademarks are the properties and registered brands of their respective owners. ii
T a b l e o f C o n t e n t s
T a b l e o f C o n t e n t s
C h a p t e r 0 Packing List........................................... 1
C h a p t e r 1 Specifications........................................ 2
C h a p t e r 2 Jumper Setting ...................................... 5
C h a p t e r 3 Connectors ............................................ 6
C h a p t e r 4 SVGA Setup ........................................... 7
Warranty ............................................................................16
iii
C h a p t e r 0
Packing List
P
Function Function
CM-2811
VGA/LCD
Module
Package
P
CM-2811 PC/104 VGA Module
Utility and Drivers x 1
(Optional)
PC/104 VGA/LCD Module User's Manual
1
C h a p t e r 1
Specifications
Features PCM-2811
Chipset
Bus Interface
Video Memory
Resolution
VGA BIOS Socket
Display Connector
Power Requirement
Board Weight
Board Size
Storage Temperature
TOPRO (HMC) TP6508IQ
PC/104 standard compliant
1MB
Up to 1024X768 @ 256 colors or
1280X1024 @ 16 colors
1
15-Pin D-type VGA,
10-Pin box-header VGA
44-pin box-header LCD)
+5V @ 200mA
75 g
96mm X 90 mm
0 ~ +60°C
2
PC/104 VGA/LCD Module User's Manual
Description
The TP6508IQ is an advanced single-chip flat panel VGA controller. It’s used for small-size computer or notebook computer system with simple operation and powerful features. Also it contains all of the functions and supports logic required to implement the IBM VGA display standards and enhanced display modes on LCD, PLASMA, EL panel and TV display at register and BIOS level compatiable. A simultaneous display technology is implemented in TP6508IQ to be used for CRT/Flat panel, LCD/TV display.
For minimum chip-count or board-space, it can design to complete a video subsystem with only one 256kx16 DRAM (512k Bytes). This video subsystem can support all panel type without any glue logic or external frame buffer.
Display memory
With 1 MB memory, the VGA controller can drive CRT displays with resolutions up to 1024 x 768 at 256 colors (or 1280 X 1024 at 16 colors).
Resolution
1280x1024 @ 16 colors
1024x768 @ 256 colors
800x600 @ 64K colors
640x480 @ 16.7M colors
Software Support/Application Drivers:
Windows 3.1/ 95/ 98/ NT
Interface
PC/104 standard compliant
Connector:
15-pin D-Type VGA external connector
10-pin box header VGA connector
44-pin box header for LCD connector
PC/104 VGA/LCD Module User's Manual
3
4
Component Location
CON1 J9
J8
J7
J6
J5
J2 J1
J3 J4
PC/104 VGA/LCD Module User's Manual
IRQ 9 Select (J1)
Close: ENABLE
Open: DISABLE
LCD Type Select (J2)
C h a p t e r 2
Jumper Setting
Type of Display 1-2 3-4 5-6 7-8 Address of VGA BIOS
DSTN Hex
3 Color DSTN 640x480
4 16-bit TFT 640x480
C C O C
C C O O
10000~17FFF Hex
18000~1FFFF Hex
5 18/24-bit TFT 640x480 C O C C 20000~27FFF Hex
6 16-bit TFT 800x600 C O C O 28000~2FFFF Hex
7 18/24-bit TFT 800x600 C O O C 30000~37FFF Hex
* Note: “C” means “close”; “O” means “open”
LCD Voltage Select (J7)
1-2: 5V
2-3: 3.3V
PC/104 VGA/LCD Module User's Manual
5
J1
J2
J3
J4
J5
J6
J7
C h a p t e r 3
Connectors
IRQ 9 Enable / Disable
LCD type select
64-pin PC/104 bus
40-pin PC/104 bus
10-pin box-header VGA connector
15-pin D-Type VGA connector
LCD Voltage Select
J8
J9
Power In
(Note)
Power Out
(Note)
CON1
44-pin LCD connector
Note
: J8 and J9 are for “Voltage to LCD after H-Sync signal ouput”
To avoid the frame flickering when power on the LCD, please use J8
(Power In) and J9 (Power out) between power supply and LCD, then the power will get in the LCD after the H-Sync appears. This is an extra function, you can use it or not.
J8 J9
Supply
LCD
6
This is an extra function, you can use it or not.
PC/104 VGA/LCD Module User's Manual
C h a p t e r 4
SVGA Setup
4.1 Introduction
The PCM-2811 has an on-board VGA interface. The specifications and features are described as follows:
4.1.1 Chipset
The PCM-2811 uses a TOPRO TP6508IQ for its SVGA controller, which supports conventional analog CRT monitor or flat panel. In addition, it also supports interlaced and non-interlaced analog monitors (color and monochrome VGA) in high-resolution modes while maintaining complete IBM VGA compatibility. Multiple frequency (multisync) monitors are handled as if they were analog monitors.
4.1.2 Display Memory
With 1 MB memory, the VGA controller can drive CRT displays or color panel displays with resolutions up to 1024 x 768 at 256 colors.
4.2 Flat Panel BIOS and Wiring
Below is a list of optional Flat Panel SVGA BIOS. The VGA BIOS is combined with the system BIOS in a single. To change to another BIOS please contact your local dealer.
MLCD.dat - Data File for MONO DSTN640*480 (Default) example : (1) HOSIDEN HLM6667
(2) HITACHI LMG5160XUFC
(3) CASIO MD650TS00-01
(4) OPTREX DMF_50260NFU-FW-8
DSTN.dat - Data file for Color DSTN640*480 example : (1) Sanyo LCM-5331-22NTK
(2) SHARP LM64C35P
TFT_S1.dat - Data File for TFT640*480-Sync (16 BIT)
PC/104 VGA/LCD Module User's Manual
7
8
TFT_S2.dat - Data File for TFT640*480-Sync (18/24 BIT) example : (1) HITACHI TX26D60/TX24D55
(2) TOSHIBA LTM09C015A
(3) SHARP LQ10D321
TFT_LP1.dat - Data File For TFT640*480-LP (16 BIT)
TFT_LP2.dat - Data File For TFT640*480-LP (18/24 BIT) example : (1) Toshiba LTM09c015A)
TFT86_S1.dat - Data File for TFT800*600_sync (16 BIT)
TFT86_S2.dat Data File for TFT800*600_sync (18/24 BIT) example : (1) NEC NL8060AC26-05
(2) NEC NL8060AC26-04
(3) NEC NL8060BC31-02
EL.dat - Data File for EL640*480 example : (1) PLANAR EL640.480-A
PLASMA.dat - Data File for PLASMA640*480 example : (1) PANASONIC S817
CRT/Flat Panel Mode
All the above BIOS support either CRT only, Flat Panel only or CRT/Flat
Panel simultaneously. To set the mode a Panel Switching Utility is used.
USAGE:
At DOS prompt type >SW508 then Screen will show
1. CRT Only
2. Panel Only
3. CRT/Panel Simutaneous
NEC NL6448AC33-18 wiring
NEC NL6448AC33-18 PCM-2811 CON1
CN1-1 GND 3 GND
PC/104 VGA/LCD Module User's Manual
CN1-15
CN1-16
CN1-17
CN1-18
CN1-19
CN1-20
CN1-21
CN1-22
CN1-23
CN1-24
CN1-25
CN1-26
CN1-27
CN1-28
CN1-2
CN1-3
CN1-4
CN1-5
CN1-6
CN1-7
CN1-8
CN1-9
CN1-10
CN1-11
CN1-12
CN1-13
CN1-14
PC/104 VGA/LCD Module User's Manual
GND
B0
B1
B2
B3
G2
G3
G4
G5
B4
B5
GND
ENAB
Vcc
CLK
Hsync
Vsync
GND
R4
R5
GND
G0
G1
R0
R1
R2
R3
34
11
12
13
14
21
22
23
24
15
16
39
37
43
31
32
33
19
20
27
28
29
30
35
38
36
4
-
P2
P3
P4
P5
P12
P13
P14
P15
P6
P7
-
MDE
Vcc
SHFCLK
LP
FLM
-
P18
P19
P20
P21
P22
P23
-
P10
P11
9
10
CN1-29
CN1-30
Vcc
NC
44
-
Vcc
-
- CN1-31 NC
NEC NL6448AC30-10 wiring
-
NEC NL6448AC30-10 PCM-2811 CON1
CN1-10
CN1-11
CN1-12
CN1-13
CN1-14
CN1-15
CN1-16
CN1-17
CN1-1
CN1-2
CN1-3
CN1-4
CN1-5
CN1-6
CN1-7
CN1-8
CN1-9
CN1-18
G2
G3
-
R0
-
-
G0
G1
CLK
Hsync
Vsync
DE
-
B0
B1
B2
B3
R1
P9
P10
P11
P12
P5
P6
P7
P8
SHFCLK
LP
FLM
MDE
P0
P1
P2
P3
P4
P13
18
19
20
21
14
15
16
17
-
10
11
12
13
42
38
36
37
22
PC/104 VGA/LCD Module User's Manual
CN1-19
CN1-20
CN1-21
CN1-22
CN1-23
CN1-24
CN1-25
CN1-26
CN1-27
CN1-28
CN1-29
CN1-30
CN1-31
R2
R3
-
-
-
-
PVcc
Vcc
MODE
-
-
-
-
31
32
5
43
44
27
28
29
30
23
24
-
-
CN1-32
CN1-33
CN1-34
CN1-35
GND
GND
Vdd +12
ENABKL
3
4
1
40
39
GND
GND
+12
ENABKL
GND CN1-36 GND
LJ32H028 wiring
LJ32H028 PCM-2811 CON1
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
LCD Vdd
Vcc
Vcc
CN1-1
CN1-2
CN1-3
CN1-4
CN1-5
D1
D0
D3
D2
CP2
11
12
9
10
35
PC/104 VGA/LCD Module User's Manual
P2
P3
P0
P1
SHF_CLK
11
12
CN1-1
CN1-2
CN1-3
CN1-4
CN1-5
CN1-6
CN1-7
CN1-8
CN1-9
CN1-10
CN1-11
CN1-6
CN1-7
CN1-8
CN1-9
CN1-10
CN1-11
CN1-12
GND
CP1
GND
S
-
-
-
3,4
38
33,34
36
-
-
-
CN1-13
CN1-14
+5V
-
CN1-15 +12V
SHARP LQ10D42 wiring
(640 X 480 TFT Color)
43,44
-
1,2
+5V(Vdd)
-
+12V
SHARP LQ10D42 PCM-2811 CON1
GND
LP
GND
FLM
-
-
-
GND
CLK
Hsync
Vsync
GND
R0
R1
R2
R3
R4
R5
3,4
21
22
23
24
25
26
3,4
42
38
36
GND
SHFCLK
LP
FLM
GND
P12
P13
P14
P15
P16
P17
PC/104 VGA/LCD Module User's Manual
CN1-12
CN1-13
CN1-14
CN1-15
CN1-16
CN1-17
CN1-18
CN1-19
CN1-20
CN1-21
CN1-22
CN1-23
CN1-24
GND
G0
G1
G2
B0
B1
B2
B3
B4
G3
G4
G5
GND
9
10
11
12
13
18
19
20
3,4
3,4
15
16
17
CN1-25
CN1-26
CN1-27
CN1-28
CN1-29
CN1-30
B5
GND
ENAB
Vcc
Vcc
R/L
14
3,4
40
43,44
43,44
-
- CN1-31 U/D
SHARP LQ12S31 wiring
(800 X 600 TFT Color)
SHARP LQ12S31 PCM-6052V CON1
P5
GND
M
Vcc +5V
Vcc +5V
-
-
GND
P6
P7
P8
P0
P1
P2
P3
P4
P9
P10
P11
GND
CN1-1 GND 3 GND
PC/104 VGA/LCD Module User's Manual
13
14
CN1-18
CN1-19
CN1-20
CN1-21
CN1-22
CN1-23
CN1-24
CN1-25
CN1-26
CN1-27
CN1-9
CN1-10
CN1-11
CN1-12
CN1-13
CN1-14
CN1-15
CN1-16
CN1-17
CN1-2
CN1-3
CN1-4
CN1-5
CN1-6
CN1-7
CN1-8
GND
G0
G1
G2
GND
G3
G4
G5
GND
GND
R0
R1
R2
GND
R3
R4
R5
GND
GND
CLK
GND
Hsync
Vsync
GND
GND
GND
39
22
23
24
41
39
19
20
21
41
30
31
32
39
39
27
28
29
8
8
8
8
35
4
38
36
PC/104 VGA/LCD Module User's Manual
GND
P10
P11
P12
P13
P14
P15
GND
GND
P18
P19
P20
GND
P21
P22
P23
GND
GND
SHFCLK
GND
LP
FLM
GND
GND
GND
CN1-28
CN1-29
CN1-30
CN1-31
CN1-32
CN1-33
CN1-34
CN1-35
CN1-36
CN1-37
CN1-38
CN1-39
CN1-40
CN1-41
GND
B0
B1
B2
GND
B3
B4
B5
GND
ENAR
TST
Vcc
Vcc
TST
41
37
-
43
44
41
14
15
16
41
11
12
13
-
GND
P2
P3
P4
GND
P5
P6
P7
GND
M
-
+5Vcc
+5Vcc
-
PC/104 VGA/LCD Module User's Manual
15
Warranty
This product is warranted to be in good working order for a period of one year from the date of purchase. Should this product fail to be in good working order at any time during this period, we will, at our option, replace or repair it at no additional charge except as set forth in the following terms.
This warranty does not apply to products damaged by misuse, modifications, accident or disaster. Vendor assumes no liability for any damages, lost profits, lost savings or any other incidental or consequential damage resulting from the use, misuse of, or inability to use this product. Vendor will not be liable for any claim made by any other related party. Return authorization must be obtained from the vendor before returned merchandise will be accepted. Authorization can be obtained by calling or faxing the vendor and requesting a Return Merchandise Authorization (RMA) number. Returned goods should always be accompanied by a clear problem description.
16
PC/104 VGA/LCD Module User's Manual
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement