Surface Fixed
Liberty Bells
Page 1 of 2
Components: x6
M10x30 Security Screw x4
2 Part Cover Cap
TX40x25mm
Driver Bit x1
Installation Instructions
(1)
1. Lay packaging out on floor and clear workspace with non-abrasive surface for assembly to prevent marking of polished stainless steel.
2. Unpack surface fix posts and plate.
3. Sheath posts over the surface plate stanchions in the order shown in image (1).
4. Secure posts to surface plate with M10x30 Security
Screws with provided Driver bit.
5.Locate Bells in desired location and mark holes to fix to desired surface.
6. Fix to Surface using recommended ground anchors (Ground Anchors are not supplied).
7. Make sure all fixings are covered and secure using cover caps provided.
8. Unpack Liberty Bell chimes.
Weight of heaviest part 8Kg (Large Bell)
9. Align the first small chime grate with the dowels on the end of the smallest post.
Screw C5 (Indigo) chime onto the smallest post, over chime grate.
10. Repeat in ascending order of post height, matching the bells in ascending order of size.
The three small chime grates match with the three smaller bells, and the three larger match with the three largest bells.
Ground Surface
Small
Beaters X4
1.5m
1330mm
1.5m
Install
Instrument with 1.5m free space (from widest point) around it.
CAUTION: Frame surface can get hot in direct sunlight, if possible install in shaded areas.
Spares available from percussionplay.com or from your local distributor
24 Kg
BS EN 1176
Surface Fixed
Liberty Bells
Page 2 of 2
Bell Assembly
1. Align chime grate with dowels and place on end of post. Ensure you have matched the correct grate size to the post (the larger match with the three larger posts and bells).
2. Select matching bell to secure onto the post. Align and gently begin to fasten clockwise.
3. With comfortable alignment, continue to rotate bell down onto post until fastened securely.
Pre-applied threadlocker on the end of the bell’s screw will prevent the bell from unfastening.
4. Lastly tighten pan-head screw on top of bell gently with spanner (16mm).
4.
Small
Beaters X4
BS EN 1176
3.
2.
1.
Spares available from percussionplay.com or from your local distributor
24 Kg
Surface Fixed
Harmony Bells
Page 1 of 3
Components: x3
M10x30 Security Screw x4
2 Part Cover Cap
Metric Conversion:
1650mm/ 64 61/64”
1.5m/ 59”
Installation Instructions
1. Unpack ground fixing legs
3no.
2. Lay packaging out on floor or assemble on non-abrasive surface to prevent marking of polished stainless steel.
3. Align holes on legs to holes on surface fixing(opposite end to polished domes) and secure in place using 3no.
M10 x 30mm Screws provided. Tools required TX
45 Driver Bit)
4. Invert assembled frame so
Bells are at the top.
5.Locate Bells in desired location and mark holes to fix to desired surface.
6. Fix to Surface using recommended ground anchors (Ground Anchors are not supplied)
7. Make sure all fixings are covered and secure using cover caps provided
Weight of heaviest part 8kg (Large Bell)
Small
Beaters X3
BS EN 1176
1650mm from Plate
1.5m
1.5m
Install
Instrument with 1.5m free space (from widest point) around it.
Ground Surface
Ground Anchors not supplied
Spares available from percussionplay.com or from your local distributor
30 Kg
Surface Fixed
Harmony Bells
Page 2 of 3
Installation Instructions
Remove nylon nut and 40mm spacer to expose threadlocker, and screw bell into post.
Components:
Saddle Straps x3 x6
M6x20 Security Screw
*Bell Flowers arrive pre-assembled.
Small
Beaters X3
BS EN 1176
Spares available from percussionplay.com or from your local distributor
30 Kg
Assembly Guide PPHARMB
Tools: x1
TX 45 Driver Bit
Surface Fixed
Harmony Bells
Page 3 of 3
1
Components: x3
M10x30 Security Screw x4
2 Part Cover Cap
Thread Lock Solution
Required
BS EN 1176
Locate the Surface fix
Plate into the leg of the instrument.
Small
Beaters X3
Thread Lock Solution
Required
2 3
Fix instrument to Surface fix plate using M10
Screws and use thread locking solution to prevent fixings working loose.
Fix Surface Plate to the ground surface Ground
Anchors Not provided cover fixings with caps provided
Ground Anchors not supplied
Spares available from percussionplay.com or from your local distributor
30 Kg
Surface Fixed
Petal Drum
Page 1 of 3
Instrument
Components: x4
M6x20 Security Screw x2
M6 Saddle Strap
Metric Conversion:
1080mm/ 42.5”
1.5m/ 59”
BS EN 1176
Installation Instructions
1. Instrument will arrive on site fully assembled. (1.1)
(See Assembly Guide)
2. Attach Surface Fixing posts to legs(1.2) (See Surface Fix
Post Installation Sheet)
3.Locate Plate in desired location and mark holes to fix to desired surface.
(1.1)
4. Fix to Surface using recommended ground anchors not supplied
(1.3) (1.2)
5. Make sure all fixings are covered and secure using cover caps provided
6. Attach the 1 of the beaters to each of the saddle strap on the hex frame. (1.3)
Weight of heaviest part 7.5kg
Pair Small Red
Beaters X1
Surface Fix
Components: x1
M10x70 Security Screw x1
M10 Barrel Nut
1.5m
1080mm
1.5m
Install Instrument with 1.5m free space
(from widest point) around it.
Ground Surface
Spares available from percussionplay.com or from your local distributor
17 Kg
Surface Fixed
Petal Drum
Page 2 of 3
Instrument
Components: x4
M6x20 Security Screw x2
M6 Saddle Strap
Assembly Guide PPPETA
(1.1)
Thread Lock Solution
Required (Not Supplied)
BS EN 1176
Thread Lock Solution
Required (Not Supplied)
Pair Small Black
Beaters X1
Surface Fix
Components: x1
M10x70 Security Screw x1
M10 Barrel Nut
Tools:
Install 3X PU Inserts into each arm x1
TX 30 Driver Bit before installing petal section x2
TX 45 Driver Bit
Spares available from percussionplay.com or from your local distributor
17 Kg
Surface Fix Post Installation
Surface Fixed
Petal Drum
Page 3 of 3
1 2
(1.1)
Components: x1
M10 Barrel Nut x1
M10x70 Security Screw
Thread Lock Solution
Required (Not Supplied)
Locate the Surface fix
Plate into the leg of the instrument.
3
Thread Lock Solution
Required (Not Supplied)
Fix instrument to Surface fix plate using M10 bolt and Barrel Nut and use thread locking solution to prevent fixings working loose.
Fix Surface Plate to the ground surface Ground
Anchors Not provided cover fixings with caps provided
BS EN 1176
