Impassa PT4 User manual

Self-Contained Wireless
Alarm System
v1.1 User Manual
WARNING: This manual contains information on limitations regarding product use and
function and information on the limitations as to liability of the manufacturer. The entire
manual should be carefully read.
Table of Contents
1. About Your Security System
1
1.1 Fire Detection (must be enabled by Installer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Carbon Monoxide Detection (must be enabled by Installer). . . . . . . . . . . . . . . . . . . . . . 1
1.3 Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.4 Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.5 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.6 General System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2. Keypad Controls & Indicators
2
3. Language Selection
2
4. Arming and Disarming the System
2
4.1 Stay Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
4.2 Night Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4.3 Silent Exit Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4.4 Away Arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4.5 Quick Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4.6 Siren Sounds After Away Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4.7 Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4.8 Remote Arming and Disarming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5. Emergency Keys
4
6. When Alarm Sounds
4
6.1 Intrusion (Burglary) Alarm Continuous Siren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
6.2 Fire Alarm Pulsed Siren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
6.3 Carbon Monoxide (CO) Alarm (must be enabled by your installer) . . . . . . . . . . . . . . . . 4
7. 2-Way/1-Way Audio Operation (SCW9057 only)
4
8. Time & Date Programming and Temperature Display
5
9. Bypassing Zones
5
9.1 Bypass Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
10.Trouble Conditions
6
11.Alarm Memory
6
12.Door Chime
6
13.Access Code Programming
7
13.1 Access Codes — [][5][Master Code] (when disarmed) . . . . . . . . . . . . . . . . . . . . . . . . 7
13.2 User Code Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
13.3 Inherent Attributes (all codes except installer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
13.4 Zone Bypassing Attribute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
13.5 Phone Access Attribute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
13.6 Bell/Siren Squawk Attribute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
13.7 Erasing an Access Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
14.Proximity Tag Enrollment (PT4/PT8)
8
15.User Function Commands
9
15.1 Changing Brightness/Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
15.2 Changing the Buzzer Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
15.3 Viewing the Event Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
16.Changing SMS Phone Numbers
10
17.Late to Open
10
18.SMS (Short Message Service) Notification
11
18.1 The SMS Notification Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
18.2 SMS Remote Access Connection Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
18.3 On-board LCD Display SMS Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
19.Two-Way Wireless Key (WT4989, WT8989)
12
19.1 Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
19.2 WT4989/WT8989 Status Display Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
19.3 Buzzer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
19.4 Keylock Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
20.Testing Your System
13
20.1 Siren and Keypad Display Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
20.2 Walk Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
20.3 Allowing Computer Access to your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
21.Reference Sheets
14
21.1 Access Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
21.2 Sensor / Zone Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
21.3 SMS Telephone Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
22.Keypad Quick Guide
16
23.Guidelines for Locating Smoke & CO Detectors
18
24.Household Fire Safety Audit
19
25.Fire Escape Planning
19
i
Always ensure you obtain the latest version of the User Guide. Updated versions of this User Guide
are available by contacting your distributor.
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electric shock and/or injury, observe the following:
• Do not spill any type of liquid on the equipment.
• Do not attempt to service this product yourself. Opening or removing the cover may expose you
to dangerous voltage or other risk. Refer servicing to qualified service personnel. Never open the
device yourself.
• Do not touch the equipment and its connected cables during an electrical storm; there may be a
risk of electric shock.
• Do not use the Alarm System to report a gas leak if the system is near a leak.
REGULAR MAINTENANCE AND TROUBLESHOOTING
Keep your Alarm Controller in optimal condition by following all the instructions that are included
within this manual and/or marked on the product.
CLEANING
• Clean the units by wiping with a damp cloth only.
• Do not use abrasives, thinners, solvents or aerosol cleaners (spray polish) that may enter through
holes in the Alarm Controller and cause damage.
• Do not use any water or any other liquid.
• Do not wipe the front cover with alcohol.
TROUBLESHOOTING
Occasionally, you may have a problem with your Alarm Controller or telephone line. If this happens,
your Alarm Controller will identify the problem and display an error message. Refer to “Trouble Conditions” on page 6 when you see an error message on the display. If additional help is required, contact your distributor for service.
WARNING: This equipment, Alarm System SCW9055/SCW9057 shall be installed and used within
an environment that provides the pollution degree max 2 and over-voltages category II non-hazardous locations, indoor only. It is designed to be installed, serviced and/or repaired by service persons
only [service person is defined as a person having the appropriate technical training and experience
necessary to be aware of hazards to which that person may be exposed in performing a task and of
measures to minimize the risks to that person or other persons]. For EU and Australian markets, the
equipment is permanently connected or direct plug-in connected. For the permanent connection
version, an accessible disconnect device shall be incorporated into the building installation wiring.
For North America the equipment uses a direct plug-in connection. For the direct plug-in version, the
socket outlet shall be installed near the SCW9055/SCW9057 and shall be easily accessible. The plug
of the direct plug-in transformer serves as the disconnect device.
NOTE: There are no parts replaceable by the end-user within this equipment, except the batteries
for the following: the WT5500 keypad, Indoor Siren (WT4901/WT8901) and the Wireless Key
(WT4989/WT8989).
WARNING: Never obstruct the access to the socket-outlet to which this equipment is connected.
These safety instructions should not prevent you from contacting the distributor and/or the manufacturer to obtain any further clarification and/or answers to your concerns.
NOTE: For SIA CP-01 installations, wireless key devices (WS4939, WS4938 and WT4989) shall
not be used for panic/alarm functionality; only for arming and disarming functions. The product
also supports Cross Zoning functionality; two zones shall be activated within the programmed
cross zone timer in order for the system to generate an alarm condition. The product also
supports the Call Waiting Cancel Dial String, which is enabled by the installer through access of
the dialing sequence used to disable call waiting.
ii
1. About Your Security System
Read this manual carefully and have your installer instruct you on your system's operation and on
which features have been implemented in your system. All users of this system should be fully
instructed in its use. Fill out the “System Information” page with all of your zone information and
access codes, and store this manual in a safe place for future reference.
NOTE: Please consult your installer for further information regarding the false alarm reduction
features built into your system, as not all are covered in this manual.
1.1 Fire Detection (must be enabled by Installer)
This equipment is capable of monitoring fire detection devices such as smoke detectors and providing a warning if a fire condition is detected. Good fire detection depends on having an adequate
number of detectors placed in appropriate locations. This equipment should be installed in accordance with NFPA 72 (N.F.P.A., Batterymarch Park, Quincy MA 02269). Please read the Family Escape
Planning guidelines in this manual.
1.2 Carbon Monoxide Detection (must be enabled by Installer)
This equipment is capable of monitoring carbon monoxide detectors and providing a warning if carbon monoxide is detected. Please read the Family Escape Planning guidelines in this manual and
instructions that are available with the carbon monoxide detector.
1.3 Testing
To ensure that your system continues to function as intended, you must test your system weekly.
Please refer to the “Testing your System” section in this manual. If your system does not function
properly, call your installing company for service.
1.4 Monitoring
This system is capable of transmitting alarms, troubles, and emergency information to a central station. If you initiate an alarm by mistake, immediately call the central station to prevent an unnecessary response.
NOTE: The monitoring function must be enabled by the installer before it can become functional.
NOTE: Consult with your installer to determine if your system is configured with a communicator
delay. A communicator delay will prevent a report to the central station if the control panel is
disarmed within 30-45 seconds after an intrusion alarm is triggered. Note that fire-type alarms are
normally reported without a delay.
NOTE: Ensure that your installer verifies that your system is compatible with the Central Station
Receiver format at yearly intervals.
1.5 Maintenance
With normal use, the system requires minimum maintenance. Note the following points:
• Do not wash the security equipment with a wet cloth. Light dusting with a slightly moistened cloth
should remove normal accumulations of dust.
• Replace the standby battery every 3-5 years.
NOTE: Do not attempt to replace the battery or open the enclosure; there is a risk of electric shock
and/or fire.
• For other system devices such as smoke detectors, motion detectors, glassbreak detectors or door/
window contacts, consult the manufacturer’s literature for testing and maintenance instructions.
1.6 General System Operation
Your security system comprises an integrated alarm control/keypad and various sensors and detectors. The keypad is mounted by the main entry/exit location. The system is self-contained; electronics
and standby battery are housed within the keypad unit.
NOTE: Only the installer or service professional should have access to the system.
The security system has several zones of area protection. Each of these zones communicates to a single wireless sensor (motion detectors, glassbreak detectors, door contacts, etc.) or to one or more
hard-wired sensors. A sensor in alarm is indicated by messages on the LCD.
Additional features include Automatic Inhibit (Swinger Shutdown) for Alarm; Tamper and Trouble
signals after 3 occurrences in a given set period; SMS interactive operation (SMS features not investigated by UL/ULC); and a Programmable Keypad Lockout option.
For SIA CP-01 classified installations, the swinger shutdown feature is programmed such that one or
two trips will shut down the zone. The zone will be restored after a manual reset (by entering the
access code at the time of disarming the alarm system) or it will be reset automatically after 48 hours
with no trips on any zones.
1
2. Keypad Controls & Indicators
2x16 LCD
< > indicates user can
scroll through options
System is
Ready to Arm
<>
Scroll Keys
Emergency Keys:
Fire
Auxiliary
Panic
1
2
3
4
5
6
7
8
9
*
0
#
LED Indicators
Ready
Armed
Trouble
Power
Function Keys:
Stay Arm
Away Arm
Chime
Bypass Zones OX
Quick Exit
Select Option
Previous Screen
IMPORTANT NOTICE
A security system cannot prevent emergencies. It is only intended to alert you and your central station (if applicable) to an emergency situation. Security systems are generally very reliable but they
may not work under all conditions and they are not a substitute for prudent security practices or life
and property insurance. Your security system must be installed and serviced by qualified security professionals. These professionals can instruct you on the level of protection that has been provided and
on system operations.
NOTE: When the keypad is in Sleep Mode it is saving battery life (backlighting). The LCD
message display will not be turned on until there is a specific reason: a key is pressed, entry delay
is started. In this mode the keypad is still functioning and nothing will be visible; however if desired,
your installer can enable the product to show the armed status while in Sleep Mode.
3. Language Selection
To display messages in different languages:
1. Press and hold both [<][>] buttons simultaneously for 2 seconds.
2. Using the [<][>] buttons, scroll through the available languages.
3. Press [,] to select your desired language.
4. Arming and Disarming the System
4.1 Stay Arming
Stay arming bypasses the interior (i.e., motion sensors) and arms the perimeter of the system (i.e.,
doors and windows). Ensure all windows and doors are closed. The Ready ( ) indicator will illuminate.
Press and hold the Stay
button until it beeps (approx. 2 seconds). Enter your access code, but
do not leave the premises. During the setting state (Exit Delay active), the Armed ( ) and Ready ( )
indicators will illuminate.
When the exit delay has expired, the alarm system is armed/set and this is indicated on the keypad
as follows: the Ready ( ) indicator will turn off, the Armed ( ) indicator will remain on.
The Armed ( ) indicator and a bypass message will be displayed. The system will automatically
ignore bypassed zones (i.e., motion sensors).
NOTE: Your installer can program a function key on the keypad to enable you to arm the system
in Stay mode instantly by holding down the function key for 2 seconds. The system arms
immediately with no beeps sounding and no exit delay. This feature must not be used in CP-01
installations.
NOTE: For SIA CP-01 listed panels, the Stay Arming Exit Delay will be twice as long as the Away
Arming Exit Delay.
NOTE: If your system is installed in accordance with SIA CP-01 Standard for False Alarm
Reduction, then the security system will arm in the Stay Armed mode if the exit delay time expires
and no exit has been made.
2
4.2 Night Arming
To night arm the system when it has been armed in Stay mode, press [][1] at the keypad. All interior zones will now be armed except for devices programmed as Night zones.
NOTE: Your installer can also program a function key on the keypad that enables you to arm the
system in Night mode by holding down the function key for 2 seconds.
Night zones are only armed in Away mode; this permits limited movement within the premises
when the system is fully armed. Ensure that your installer has provided you with a list identifying
zones programmed as night zones. When the interior zones are activated (i.e., [][1]) you must
enter your access code to disarm the system in order to gain access to interior areas that have not
been programmed as night zones.
4.3 Silent Exit Delay
If the system is armed using the Stay button or using the “No Entry” Arming method ([][9] [Access
Code]), the keypad buzzer will be silenced and the exit time will be doubled for that exit period
only. (CP-01 only).
4.4 Away Arming
Close all sensors (i.e., stop movement around motion detectors, close doors and windows). Ensure
the Ready ( ) indicator is on.
To arm, press and hold the Away button for 2 seconds and/or enter your access code or press [][0]
to Quick Arm.
During the setting state (exit delay active) the Armed ( ) and Ready ( ) indicators will turn on, and
the keypad will sound one beep per second. You now have ___ seconds to leave the premises
(please check with your installer to have this time programmed). A keypad buzzer, whose pulsating
rate is distinct, will sound during the last ten seconds of the exit delay to indicate that the exit delay
is running out. To cancel the arming sequence, enter your access code.
When the exit delay has expired, the alarm system is armed and is indicated by the following: the
Ready ( ) indicator will turn off, the Armed ( ) indicator will remain on and the keypad will stop
sounding.
NOTE: The system can also be armed/disarmed with a wireless key and with prox tags. Refer to
the “Proximity Tags” and “Two-Way Wireless Key” sections for more details.
NOTE: If your system is installed in accordance with SIA CP-01 Standard for False Alarm
Reduction, the following holds true: Violation and restoral, followed by a second violation of the
entry/exit zone before the end of the exit delay, will restart the exit delay.
4.5 Quick Exit
If the system is armed and you need to exit, use the Quick Exit function to avoid disarming and
rearming the system. Press and hold the Quick Exit button
for 2 seconds or press [][0]. You
now have 2 minutes to leave the premises. When the door is closed again, the remaining exit time
is cancelled.
4.6 Siren Sounds After Away Arming
Audible Exit Fault
In order to reduce false alarms, the Audible Exit Fault is designed to notify you of an improper exit
when arming the system. If you fail to securely close the entry/exit door during the programmed exit
delay period, the system will sound the alarm to indicate an improper exit (your installer will tell you
if this feature has been enabled on your system). If this occurs:
1. Re-enter the premises.
2. Enter your access code to disarm the system before the entry delay timer expires.
3. Repeat the Away arming procedure, ensuring that the entry/exit door(s) are secured.
Arming Error
An error tone will sound if the system is unable to arm. This will happen if the system is not ready to
arm (i.e., sensors are open), or if an incorrect user code has been entered. If this happens, ensure all
sensors are secure, press [#] and try again.
4.7 Disarming
To disarm an armed system (Armed ( ) indicator is On), enter your access code. If your keypad is in
Sleep mode, press any key to wake it up then enter your access code. The keypad will sound a continuous tone after the entry delay has been initiated by opening the entry/exit door. Enter your code
within ____ seconds to avoid an alarm condition (check with your installer to program this time).
3
Disarming Error
If your code is invalid, the system will not disarm and a 2-second error tone will sound. If this happens, press [#] and try again.
4.8 Remote Arming and Disarming
The system can be armed and/or disarmed, if programmed by the installer, using a remote control
device (wireless key). When arming the system using the Arm button on a wireless key, the system
will acknowledge the command by sounding a single bell/siren squawk, if programmed to do so by
the installer. When disarming using the Disarm button on a wireless key, the system will acknowledge the command by sounding two bell/siren squawks. Three squawks, when disarming with the
Disarm button, indicates that an alarm occurred while the system was armed. If you are unsure of
the cause of the alarm, proceed with caution (see section on 2-way Wireless Keys).
5. Emergency Keys
Press BOTH
(Fire),
(Auxiliary), or
(Panic) buttons for 2 seconds to
generate a Fire, Auxiliary, or Panic alarm. The keypad buzzer will beep indicating that the alarm
input has been accepted and transmission to the central station is underway. The Fire buttons may
or may not sound the siren depending on installer setup.
NOTE: The Fire buttons can be disabled by the installer.
NOTE: The Auxiliary Alarm buttons are not intended to be used for medical signals.
6. When Alarm Sounds
The system can generate 3 different alarm sounds:
• Continuous Siren = Intrusion/Burglary Alarm
NOTE: The WT4911 siren will sound a dual frequency sweeping tone for burglary alarms.
• Temporal / Pulsed Siren = Fire Alarm
• 4 beeps, 5-second pause, 4 beeps = Carbon Monoxide alarm
NOTE: The priority of signals is fire alarm, carbon monoxide alarm then burglary alarm.
6.1 Intrusion (Burglary) Alarm Continuous Siren
If you are unsure of the source of the alarm, proceed with caution! If the alarm was accidental,
enter your access code to silence the alarm. If the alarm system is disarmed within the programmed
Abort Window (check with the installer if this option has been enabled on your system and what is
the programmed transmitter delay time is), no alarm transmission to the Central Station will occur. A
5-minute Cancel Window follows the Abort Window, during which a user can cancel an alarm that
has been previously transmitted (by entering their access code). A cancel signal will be transmitted to
the central station and the alarm system will also announce that the cancel signal was transmitted.
Call your central station to avoid a dispatch.
6.2 Fire Alarm Pulsed Siren
Follow your emergency evacuation plan immediately!
If the fire alarm was accidental (burned toast, bathroom steam, etc.), enter your access code to
silence the alarm. Call your central station to avoid a dispatch.
6.3 Carbon Monoxide (CO) Alarm (must be enabled by your installer)
Activation of your CO alarm indicates the presence of carbon monoxide (CO), which can be fatal.
During an alarm, the red LED on the CO detector flashes rapidly and buzzer sounds with a repeating
cadence of: 4 quick beeps, 5-second pause, 4 quick beeps. If an alarm sounds:
1. Press the button on the CO detector to silence the alarm.
2. Call emergency services or your fire department.
3. Immediately move outdoors or to an open door/window.
WARNING: Carefully review your Carbon Monoxide Installation/User Guide to determine the
necessary actions required to ensure your safety and ensure that the equipment is operating correctly. Incorporate the steps outlined in the guide into your evacuation plan.
7. 2-Way/1-Way Audio Operation (SCW9057 only)
If programmed by the installer, this feature allows the monitoring station to initiate a 2-way audio
(talk/listen) or 1-way audio (listen-in only) session when an alarm has been received. This feature is
used to verify the nature of the alarm or determine the type of assistance required by the occupant.
NOTE: This feature can be initiated only by the monitoring station after an alarm has been
received. The user can not initiate a 2-way audio session.
4
8. Time & Date Programming and Temperature Display
Press [][6] then enter your master access code to enter User
Functions. Use the [<][>] buttons to view available menu
options, then press [] to select. Enter the time in 24-hr. format
(HH:MM), followed by the date (MM:DD:YY).
Press [#] to exit programming. If you are viewing a “Loss of Clock” trouble from within the trouble
menu ([][2]), press [] to directly enter Date and Time programming (see Trouble Conditions).
NOTE: Your installer may have programmed your system to display the time and date while the
keypad is idle. Press the [#] button to temporarily clear the date and time display if desired.
NOTE: The SCW9055/9057 clock display can be automatically programmed if a 3G
Communicator is connected. This feature must be enabled by your installer.
The SCW9055/SCW9057 system and WT5500 keypad can also display the outdoor temperature
(Farenheit or Celsius) from the 2-way outdoor siren. This feature must be enabled by your installer.
HH:MM MM/DD/YY
09:06 01/31/11
9. Bypassing Zones
Use the zone bypassing feature when you need access to a protected area while the system is
armed, or when a zone is temporarily out of service but you need to arm the system. Bypassed
zones will not be able to sound an alarm. As a result, bypassing zones reduces the level of security.
If you are bypassing a zone because it is not working, call a service technician immediately so that
the problem can be resolved and your system returned to proper working order. Ensure that no
zones are unintentionally bypassed when arming your system. Zones cannot be bypassed once the
system is armed. Bypassed zones (except for 24-hr zones) are automatically cancelled each time the
system is disarmed and must be bypassed again, if required, before the next arming.
With the system disarmed:
1. Press [] to enter the function menu. The keypad will display the
screen on the right.
2. Press [1] or [].
3. If your system is programmed to require access codes the screen on
the right will be displayed. Enter your 4-digit access code.
4. Scroll to the desired zone number using the [<][>] keys, then press []
to select the zone or directly enter the 2-digit number of the zone
you wish to bypass (e.g., 0 5 for zone 5).
Activating All Bypassed Zones
To remove bypass (all zones):
1. Press [][1], then your access code.
2. Press [0][0].
3. To exit bypassing mode and return to the Ready state, press [#].
Recalling Bypassed Zones
To recall the last set of bypassed zones:
1. Press [][1], then your access code.
2. Press [9][9].
3. To exit bypassing mode and return to the Ready state, press [#].
9.1 Bypass Group
A Bypass Group is a selection of zones programmed into the system. If you bypass a group of zones
on a regular basis, you can program them into a Bypass Group, so that you do not have to bypass
each zone individually. Note that only one Bypass Group can be programmed at a time.
To program a Bypass Group:
1. Press [][1], then enter your access code.
2. Enter the 2-digit number (01-64) of the zone to be included in the Bypass Group or use the [<][>]
buttons to scroll through the available zones. Press [] to select the zone.
3. To save the selected zone into the group, press [9][5].
4. To exit bypassing mode and return to the Ready state, press [#].
5
NOTE: If an access code is required to enter bypassing, only the master code and codes with
Supervisory enabled can set the Bypass Group.
To select a Bypass Group when arming the system:
1. Press [][1], then your access code.
2. Press [9][1]. The next time the system is armed, the zones in this group will be bypassed.
3. To exit bypassing mode and return to the Ready state, press [#].
NOTE: A Bypass Group is only recalled if the system is armed/disarmed after programming the
Bypass Group.
NOTE: This feature is not to be used in UL Listed installations.
10. Trouble Conditions
When a trouble condition is detected, the Trouble ( ) indicator will turn on and the keypad will beep
every 10 seconds. Press the [#] button to silence the beeps. Press [][2] to view the trouble condition.
The Trouble ( ) indicator will flash. Use the scroll [<][>] keys to view troubles.
Trouble
Comments
Action
Call for service.
For Ethernet Trouble
check LAN connections.
Alternate
Communicator Trouble
Indicates SIM Card Lock, 3G Network Trouble, Ethernet Trouble,
Central Station Receiver Trouble, Supervision Trouble, and SMS
Config Trouble. Press [<][>] to scroll through individual troubles.
Service Required
(Press [1] for more information)
Indicates Low Battery, System Trouble, System Tamper or RF Jam Call for service.
detected.
Loss of AC Power
If the building and/or neighbourhood has lost electrical power, Check AC
the system will continue to operate on battery power for several connection.
hours.
Call for service.
Telephone Line Fault
The system has detected that the telephone line is disconnected.
Failure to
Communicate
The system attempted to communicate with the monitoring sta- Call for service.
tion but failed. This may be due to a telephone line Fault.
Module/Sensor Fault
The system is experiencing difficulties with one or more module/ Call for service.
sensor on the system. Continue to press [5] to navigate through
the zone, keypad, and siren fault menus.
Module/Sensor Tamper
The system has detected a tamper condition with one or more Call for service.
module/sensor on the system. Continue to press [6] to navigate
through the zone, keypad, and siren tamper menus.
Module/Sensor Low Battery
The system has detected a low battery condition with one or
more module/sensor on the system. Continue to press [7] to
display the zone(s), wireless key(s), keypad(s), siren(s) and prox
tag(s).
Loss of Time & Date
If complete power was lost (AC and Battery), the time and date Reprogram Time &
Date.
will need to be re-programmed. Press [].
Blank Display/No
Response
Keypad battery may have discharged beyond the usable level.
“Panel Response Not
Received” message
The keypad has lost wireless communication with the panel.
If trouble persists, call
Occasional display of this message may be caused by local radio for service.
frequency interference.
Call for service.
See section on Siren
Test. Call for service.
Replace battery (call
for service if trouble
not cleared).
11. Alarm Memory
When an alarm occurs, the Alarm Memory message will be displayed. To view which sensor(s) generated the alarm, press [][3]. For the system keypad use the scroll [<][>] buttons to view the sensors in
alarm memory. Press [#] to exit. To clear the memory, arm and disarm the system.
If an alarm sounded while armed, the system will automatically go to alarm memory when you disarm the system. In this instance, you should proceed with caution, as the intruder may still be within
the building/premises.
12. Door Chime
To turn the door chime function on or off, press and hold the Chime
button for 2 seconds or
press [][4]. The system will sound 3 beeps to indicate the door chime is on, or one long tone to indicate that door chime is off.
6
13. Access Code Programming
In addition to the master code, you can program up to 16 additional user access codes.
To program User Access Codes:
1. Disarm your system, if it is armed.
2. Press [][5][Master Access Code (i.e., 4- or 6-digit code)]; the armed ( ) indicator will turn on.
3. Enter the 2-digit number to be programmed. This number is used to identify the User Access
Code being entered (e.g., 06 for User Access Code 6; enter 40 for the master access code), or
press the scroll [<][>] buttons to find the specific code and press [] to select.
4. Enter the new 4-digit or 6-digit access code. When programming is complete, enter another 2digit code to program or press [#] to exit.
The access codes have programmable attributes which allow zone bypassing, duress, supervisor,
remote access, or one-time use activation.
On WT5500P keypads, you will be prompted to swipe a prox tag once the last character of the
access code is entered. To delete prox tags, the associated user access code must be deleted as
described, then re-programmed if required.
NOTE: If wireless keys have been programmed then wireless key #1 will log as User Access Code
#1 (if that access code has been programmed). User Access Codes 1-16 will correspond to
wireless keys or prox tags 1-16.
NOTE: When using 6-digit access codes, the minimum number of variations of access codes are
58,823.
13.1 Access Codes — [][5][Master Code] (when disarmed)
The [][5] User Programming command is used to program additional access codes (see Access Code
Programming).
User Codes - User codes 1-16 are available for the system.
Master Code (Access Code 40) - The master code has all of the attributes listed in the Programmable Attributes list below except for Duress (2) and One-Time Use (8) and is required to program all
supervisor code attributes.
Supervisor Codes - These codes are always valid when entering the [][5] User Code Programming
or [][6] User Function sections. However, these codes can only program additional codes which have
equal or lesser attributes. Once programmed, the supervisor codes receive the master code’s attributes. These attributes are changeable. Any user code can be made a supervisor code by enabling
User Code Attribute 1 (please see below for details).
Duress Codes - Duress codes are standard user codes that will transmit the Duress Alarm Reporting
Code whenever the code is entered to perform any function on the system. Any user code can be
made a duress code by enabling User Code Attribute 2 (see below for details).
One-Time Use Code - This code permits temporary access to the system for a 24-hour time period.
During the 24hr period, the temporary user may disarm the system once. There is no restriction on the
number of times the temporary user may arm the system during the time period.
NOTE: Duress codes are not valid when entering [][5], [][6] or [][8] sections.
NOTE: Access codes cannot be programmed as a duplicate or as a Code +/- 1.
13.2 User Code Attributes
1. The default attributes of a new code will be the attributes of the code used to enter [][5]
whether it is a new code or an existing code being programmed.
2. System Master (Code 40) has Attribute 3 on by default.
NOTE: These attributes are not changeable.
13.3 Inherent Attributes (all codes except installer)
Arm / Disarm - Any access code will be valid for arming and disarming the system.
Command Outputs ([][7][1] and [][7][2]) - If these outputs require access code entry, any access
code is valid for performing the [][7][1-2][Access Code] functions on the system.
Programmable Attributes ([][5][Master/Supervisor Code][9][Code])
To program an access code attribute enter [][5][Master/Supervisor Code][9] then [<][>] scroll to the
access code (e.g., 2-digit number 01-16) you want to program. Press [] to select the access code.
7
Next, scroll [<][>] to the attribute you want to program and press [] (or enter the attribute #) to
enable/disable the attribute.
# Attribute
1 Supervisor Code
#
Attribute
5-6 For Future Use
2 Duress Code
7
Bell/Siren Squawk upon Away Arming/Disarming
3 Zone Bypassing Enabled
8
One-Time Use Code
4 Phone Access
13.4 Zone Bypassing Attribute
This attribute allows the user to manually bypass zones if bypassing requires an access code.
13.5 Phone Access Attribute
This attribute allows the user to specify which user access codes can be used for remote access via
SMS.
13.6 Bell/Siren Squawk Attribute
This attribute is used to determine whether an access code should generate an arming/disarming
squawk when the away function key is pressed on a wireless key. Contact your installer to have this
programmed. The Master code cannot use the Bell/Siren Squawk attribute, but the code is required
to enable the Bell/Siren for other codes.
NOTE: This feature cannot prevent the Arm/Disarming squawks from being generated if an
access code assigned to a wireless key is manually entered at a keypad.
13.7 Erasing an Access Code
To erase a code, select the code and enter [] as the first digit. If [] is entered, the system will delete
the code (including the associated prox tag) immediately and the user will be returned to select
another code.
14. Proximity Tag Enrollment (PT4/PT8)
Proximity (prox) tag readers are only available on WT5500P keypads. Refer to the label on top of the
keypad to confirm which model you have.
Enrolling Proximity Tags
1. Enter [][5][Master Code] to enter User Code Programming.
2. Scroll to the desired user code (01-16, or 40 for the master code) then press [].
3. Enter your desired 4 or 6-digit user access code. The following message will be displayed after the
user access code is entered:
Present Tag or
Press # to Exit
4. Place the prox tag near the tag reader ( ) at the left side of the display to assign it to the user
code. The following message will be displayed:
Tag Enrolled
Successfully
5. If an attempt is made to assign a prox tag to an existing user code that has an associated prox
tag, the following message will be displayed.
Duplicate
Tag/User Code
Select another user code or erase the existing user code and associated prox tag and re-enroll with
the new prox tag. Return to Step 2 for instructions on how to enroll a user code.
NOTE: To exit the process at anytime, press [#].
Erasing a User Code/Proximity Tag
Enter [][5][Master Code], select the desired user code. Enter [] to erase the code and associated
prox tag. The keypad will display the user number (e.g., 01) with a letter “P” if a user code has
already been programmed and a letter “T” if a code and prox tag have been programmed.
NOTE: User 40 for the master code cannot be deleted; an attempt to delete this user code will
delete the prox tag only. The prox tag must be re-enrolled before it can be used again.
8
Proximity Tag Operation
6. Place the prox tag near the tag reader ( ) at the left side of the display to arm/disarm your system. When arming the system, the following message will be displayed:
Exit Delay in
Progress
7. When disarming the system, the following message will be displayed:
System Disarmed
8. If there is an attempt to swipe a prox tag that has not been enrolled, an error tone will sound and
the following message will be displayed:
Invalid Tag
Return to Step1 for instructions on how to enroll the prox tag.
WARNING: KEEP THE PROXIMITY TAG OUT OF REACH OF SMALL CHILDREN.
THE MATERIALS ASSOCIATED WITH THIS PRODUCT (LITHIUM BATTERIES, ETC.) MUST BE RECYCLED ACCORDING TO LOCAL RULES AND REGULATIONS.
15. User Function Commands
Disarm the system then enter [][6][Master Code]. The [][6] command is used to gain access to the
following list of Master functions of the system:
[1] Time and Date - Enter 4 digits for 24hr System Time (HH-MM). Valid entries are 00-23 for the
hour and 00-59 for minutes. Enter 6 digits for the Month, Day and Year (MM-DD-YY).
[2]-[3] For Future Use.
[4] System Test - The system tests siren output: on-board siren – 4 seconds (2 seconds medium
volume, 2 seconds high volume), indoor/outdoor siren – 2 seconds. Keypad lights, back-up battery
pack and communicator are tested.
[5] Enable DLS / Allow Remote System Service - If enabled, the installer can to access Installer
Programming remotely using DLS (Downloading Software). This function provides a window for telephone ring detection by the alarm system. The DLS window will remain open for 6 hours, during
which time the installer will be able to enter DLS an unlimited number of times. After the 6-hr window has expired, access to programming via DLS will be unavailable until the window is re-opened.
[6] User Call-up - If enabled by the installer, the panel will make 1 attempt to call the downloading
computer. The downloading computer must be waiting for the panel to call before downloading can
be performed.
[7] For Future Use.
[8] User Walk Test - Allows the user to enter the Walk Test mode. See Walk Test on page 14.
[9] Late to Open Enable/Disable - This function enables or disables the Late to Open time programmed in [0].
[0] Late to Open Time of Day - This function is used to program the time setting enabled in [9].
NOTE: Refer to “Late to Open” section for details.
15.1 Changing Brightness/Contrast
When this option is selected, the keypad will allow you to scroll through 4 brightness levels and 10
contrast levels.
1. Press [][6] [Master Code].
2. Use the [<][>] buttons to scroll to either Brightness Control or Contrast Control.
3. Press [] to select the setting you want to adjust.
4. a) Brightness Control: There are 4 backlighting levels. Use the [<][>] buttons to scroll to the
desired level.
b) Contrast Control: There are 10 different display contrast levels. Use the [<][>] buttons to
scroll to the desired contrast level.
5. To exit, press [#].
9
15.2 Changing the Buzzer Level
When this option is selected, the keypad will allow you to scroll through 21 different buzzer levels. A
level of 00 disables the buzzer.
1. Press [][6] [Master Code].
2. Use the [<][>] buttons to scroll to Buzzer Control, then press [] to select.
3. There are 21 levels; use the [<][>] buttons to scroll to the desired level. Press [#] to exit.
15.3 Viewing the Event Buffer
The event buffer will show you a list of the last 500 events that have occurred on your system.
1. Press [][6][Master Code].
2. To select Event Buffer viewing, press [].
3. The keypad will display the event number and the time and date. Press [] to switch between this
information and the event details.
4. Use the [<][>] buttons to scroll through the events in the buffer.
5. To exit event buffer viewing, press [#].
16. Changing SMS Phone Numbers
This section tells you how to program your SMS phone numbers:
1. Enter [][6][Master Code] to enter the Master User Functions of the system.
2. Use the [<][>] buttons to scroll to the SMS programming prompt.
Select Option <>
SMS Programming
3. Press [] to select the SMS phone numbers or to see your panel’s cellular phone number. The following message is displayed:
Press () for <>
Phone No.1 P
“P” denotes whether the phone number has
been programmed.
• To see your panel’s cellular phone number use the [<][>] buttons to scroll to the following message. Then press [] to view the number.
Press () for <>
Cell Phone No.
Pressing [] here shows your panel’s cellular telephone number.
4. Press [] to select Phone No. 1. The following 26-digit phone number screen is shown.
DFFFFFFFFFFFFFFF
FFFFFFFFFFFFPH#X
X=1 to 8 to indicate the phone number screen
being programmed. (e.g., X=1 for Phone No. 1)
5. Program a new phone number or delete an existing phone number as follows:
• To Enter a new telephone number (e.g., 4168889999), enter your numbers starting at the
first F (after the D), see below.
D4168889999FFFFF
FFFFFFFFFFFFPH#1
Do not delete the remaining F’s.
• To Delete an existing phone number, replace the letter D with an F by pressing [][6][]
and then press [#] to exit. This will delete the phone number.
F4168889999FFFFF
FFFFFFFFFFFFPH#1
6. Use the [<][>] buttons to scroll to another telephone number to be programmed.
7. Repeat from Step 4 to enter more phone numbers. To exit the process at anytime, press [#].
17. Late to Open
This feature allows a user to be notified if their alarm system is not disarmed by a programmed time
of day.
NOTE: The Late-to-Open feature requires the monitoring station to forward calls to the user. Verify
with the installer whether this function is active.
10
[9] Late-to-Open Enable/Disable
The Late to Open feature enables or disables the Late to Open time programmed in [0].
It is typically used to track children after school. For example, if the parents get home from work at
5pm, and a child gets home at 4 p.m. The programmable timer could be set for 4:15 p.m. If the system is not disarmed at this time an alert would be sent to the monitoring station.
The keypad will display “Late to Open is Enabled” and sound 3 beeps if [9] is pressed within the User
Functions menu when this feature is off. The LCD keypad will display “Late to Open is Disabled” and
sound an error tone if [9] is pressed within the User Functions menu when this feature is on.
[0] Late-to-Open Time of Day
This function is used to program the time setting enabled in [9]. This function programs the “Late
to Open” time of day for all 7 days of the week.
• Valid entries for these sections are 00:00 – 23:59.
• Entering 99:99 will disable the “Late to Open” feature for the current day.
• After entering [][6][Master Code][0], beeps will be sounded and “Press () for < > Sunday” will be
displayed on the keypad.
• Pressing the right scroll [>] button displays the days of the week, from Sunday to Saturday. While in
the Late to Open menu, entering keys 1-7 will also select each day from Sunday to Saturday,
respectively.
• If [] is pressed to select a day of the week, no beeps will be sounded and “Set 24hr Time”, “Enter
HH:MM 9999” will be displayed. If [#] is pressed from this menu, the user will be returned to the
previous Late to Open menu.
• If the Alarm System is armed in any mode when the late to open time matches the time of day, Late
to Open will be logged to the event buffer and communicated to the monitoring station.
18. SMS (Short Message Service) Notification
SMS Notification occurs when the control panel sends a text message to the user for each system
event that occurs. These text messages are limited to 32 characters.
NOTE: SMS Notification is not available in North America.
Interactive SMS allows the user to send a text message (in one of 28 languages, depending on
SMS Interactive language selection) to the control panel and perform a set of functions on the panel.
There are 12 pre-defined text message commands available that the user can send to the control
panel. Please refer to the SMS Reference Card to find the text used for other languages.
NOTE: Interactive SMS is available in North America.
18.1 The SMS Notification Sequence
The panel will send an SMS notification for every event that the panel can communicate. SMS notification messages are programmed by your installer from the keypad or by using DLS IV. Text messages
can be programmed in the language of your choice.
There are 8 SMS phone numbers available to support SMS messages. An SMS phone number can be
changed using [][6][Master Code]. Refer to the Changing SMS Phone Numbers section for
detailed instructions.
18.2 SMS Remote Access Connection Sequence
This feature allows you to control your security system remotely via SMS.
1. Determine which action to perform remotely on the panel. Please refer to the SMS Reference card
for details on how to enter the text required.
All SMS remote access functions require an access code, with the exception of the help function.
The following list is an example of the functions available.
Functions
• stay arm
• activate command output 1
• alarm memory request
• away arm
• activate command output 2
• keypad message
• disarm
• deactivate command output 1
• help list of available commands
• bypass
• deactivate command output 2
• unbypass
• status request
NOTE: The default text (see SMS Reference card) used to perform each action can be changed
for you by your installer.
11
2. Compose an SMS message that consists of the function text, a space, and your 4-digit or 6-digit
access code (e.g., Stay Arm 2234) then send it to your panel’s cellular phone number.
3. The panel matches the incoming phone number to one of the phone numbers in its SMS Phone
number list.
4. The panel verifies the contents of the SMS message and performs the action.
5. When the action is completed, the panel sends an SMS message containing “function successful” back to the user. If the function or access code is invalid, the response will include function
unsuccessful” in the SMS message.
6. A one hour System Lockout is caused by entering 5 invalid access codes. If you receive the message “function failed”, the system has locked you out and you must wait one hour before using
SMS remote access, again.
18.3 On-board LCD Display SMS Messages
In addition to function commands, you can also send general SMS messages to your keypad display
from your mobile phone using the “Keypad Message” function command. A 10-second steady
tone will sound when your message appears on the keypad display. This message is displayed until
you press any button to clear. The number of key presses required to remove the message is programmed by your installer. To send a message to your keypad display:
1. Enter Keypad Message<space>1<space><access code><space><your message>.
2. Send to your panel’s cellular telephone number.
NOTE: The keypad can display a maximum of 32 characters.
19. Two-Way Wireless Key (WT4989, WT8989)
The two-way wireless key communicates directly with the control panel, performing many of the
functions that a wireless keypad performs. Please refer to the WT4989/8989 operating instructions
for more information.
The WT4989 and WT8989 have 4 function keys programmable for 6 functions each, an LCD icon
display that can display system status using a combination of 7 icons and an internal buzzer. Unless
custom programmed by your installer, the functions are as follows:
19.1 Function Keys
Status Request - Press this button for 1 second to view the control panel system status via
the LCD display icons.
Stay Arming - Press to arm your system in Stay mode. All perimeter zones are active but
interior zones remain inactive.
Away Arming - Press to arm your system. Interior and exterior zones will be armed.
Disarm - Press to disarm your system.
Panic Alarm - Press & hold for 3 seconds to create a panic alarm on the security system.
*Command Output 1 - Press & hold both buttons at the same time for 3 seconds to activate the assigned output.
*Command Output 2 - Press & hold both buttons at the same time for 3 seconds to activate the assigned output.
19.2 WT4989/WT8989 Status Display Icons
The table below summarizes the status that can be shown by the WT4989/WT8989 LCD:
ICON (S=Steady, F=Flashing)
(S) System Trouble
(S) Alarm in Memory
(F) Keylock Enable
(F) Active Alarm
(S) Disarmed
(F) [][9] Armed - Away
(S) Away - Armed
(F) [][9] Armed - Stay
(S) Stay - Armed
(F) [][9] Armed - Night
(S) Night - Armed
(S) Low Battery
(F) Critical Low Battery
12
19.3 Buzzer
Provides an audible confirmation of a pressed button or that a command to the panel has been executed.
19.4 Keylock Mode
Ensures that the system is not accidently armed or disarmed by the wireless key.
To lock the keys:
1. Press and hold the Status
and Away
keys simultaneously for 3 seconds.
2. After 3 seconds, the wireless key will beep and flash the keylock icon (
) to indicate that the
keys are locked.
To unlock the keys:
1. Press and hold the Status
and Away
keys simultaneously for 3 seconds.
NOTE: Pressing the Panic
key for 3 seconds will also exit Keylock mode.
2. Upon exiting Keylock mode, the status will be automatically displayed.
20. Testing Your System
NOTE: Inform your Monitoring Station when you begin and end system testing.
Household fire alarm systems shall be tested by a qualified service technician at least every 3 years in
accordance with NFPA72. It is the user’s responsibility to test the system weekly (excluding smoke
detectors). Ensure you follow all the steps in the two tests below.
NOTE: Should the system fail to function properly, call your installer immediately for service.
20.1 Siren and Keypad Display Test
The test activates all display pixels and indicator lights on the keypad and does a 4-second check of
the siren.
1. Press [][6][Master Code][4]. The following will occur:
- The system activates the siren output for 2 seconds followed by full volume alarm for 2 seconds.
All display lights and LCD pixels will turn on.
- The Ready, Armed, Trouble and Power LED’s will flash for the duration of the test.
2. To exit the function menu, press [#].
Keypad Low Battery
The flashing trouble icon
on a keypad will indicate
that keypad has a low battery.
Mounting
Holes
Tamper
Switch
WT5500 Keypad Battery Replacement
WT4901/WT8901 Siren Battery Test
Batteries
$$
Wire
Channel
$$
$$
$$
Plug
DG009048
1. Slide the keypad up and out from the mounting
plate/desk stand (removing the screws first if
required). The bay for the four AA batteries is open
and visible at the back of the keypad.
2. Insert the batteries as directed on the back of the
keypad. Ensure the correct polarity is observed.
3. Slide the keypad back onto the mounting plate /
desk stand.
Mounting
Holes
To determine which siren has a low battery press and hold the test button, located at the front of the
siren, for 5 seconds.
• If the siren sounds for 4 seconds, the batteries are good.
• If the siren doesn’t sound, the batteries are low.
WT4901/WT8901 Siren Battery Replacement
• Open the front cover and remove old batteries. Once the old batteries are removed, wait 30 seconds before inserting the replacement batteries.
• Install new batteries as shown in the polarity indicated by the engraving. If the batteries are
installed incorrectly, in the reverse polarity, the indoor siren will not work. With typical use, the
WT4901/WT8901 batteries should be replaced every 2 years.
NOTE: Only use Energizer (4) 1.5V AA alkaline batteries (WT5500, WT4901/WT8901).
DO NOT RECHARGE THESE BATTERIES. DISPOSAL OF USED BATTERIES MUST BE MADE IN
ACCORDANCE WITH THE WASTE RECOVERY AND RECYCLING REGULATIONS IN YOUR AREA.
13
20.2 Walk Test
Walk Test mode allows you to test the operation of each detector in the system. While in Walk Test
mode, the Ready, Armed, and Trouble LED's will flash to indicate that the Walk Test is active. The
Walk Test can be terminated at anytime by re-entering [][6] [Master Code][8] on the keypad. The
system will also automatically terminate the Walk Test on completion; it will sound an audible warning (5 beeps every 10 seconds), beginning 5 minutes before the termination of the test.
1. Before testing, ensure that the system is disarmed and the Ready light is on.
2. Press [#] and close all zones to return the system to the Ready state.
3. Perform a System Test by following the steps in the previous section.
4. Press [][6][Master Code][8] to initiate the Walk Test.
5. To test the zones, activate each detector in turn (e.g., open each door/window or walk in motion
detector areas). The System will display the following message “Secure System Before Arming < >”,
or “Secure or Arm System” when each zone (detector) is activated. Use the [<][>] buttons to view
which zones are open. The message will disappear when the zones are closed.
20.3 Allowing Computer Access to your System
Occasionally, your installer may need to send information to or retrieve information from your security system. Your installer will do this by having a computer call your system. You may need to prepare your system to receive this downloading call.
To do this: Press [][6][Master Code][5] at the keypad. This allows downloading for a limited period
of time. During this time, the system will answer incoming downloading calls. For more information
on this feature, please ask your installer.
21. Reference Sheets
Fill out the following information for future reference and store this guide in a safe place.
System Information
Enabled?
FIRE
AUXILIARY
PANIC
The Exit Delay Time is _______ seconds.
The Entry Delay Time is _______ seconds.
For Service
Central Station Information:
Account#: ___________________ Telephone#: __________________
Installer Information:
Company: ___________________ Telephone#: __________________
If you suspect a false alarm signal has been sent to the central monitoring station,
call the station to avoid an unnecessary response.
Battery Installation / Service Dates:
________________________
________________________
________________________
14
21.1 Access Codes
Master Code [40]: ______________________ Proximity Tag: Code
01
02
03
04
05
06
07
08
Wireless
Key
Prox
Tag
Access Code
Code
Wireless
Key
Prox
Tag
09
10
11
12
13
14
15
16
Access Code
21.2 Sensor / Zone Information
Sensor
Protected Area
Sensor Type
Sensor
01
33
02
34
03
35
04
36
05
37
06
38
07
39
08
40
09
41
10
42
11
43
12
44
13
45
14
46
15
47
16
48
17
49
18
50
19
51
20
52
21
53
22
54
23
55
24
56
25
57
26
58
27
59
28
60
29
61
30
62
31
63
32
64
15
Protected Area
Sensor Type
21.3 SMS Telephone Numbers
#
SMS
01
02
Phone Number
#
SMS
05
06
03
07
04
08
Phone Number
Site Identification Message: ___________________________________
Panel’s Cellular Phone Number: ___________________________________
22. Keypad Quick Guide
The following table summarizes the keys, indicators, and most often used commands of the keypad.
Keypad Keys, Indicators, and Commands
Status Lights
Ready - Must be on to arm system. All zones must be secured or bypassed and the system disarmed for this light to activate.
Armed - Indicates system is armed. If the Ready light and the Armed light are both on it indicates
an Exit Delay is in progress.
Trouble - On indicates a system malfunction or tamper. Flashing indicates that the keypad has a
low battery condition. Follow the instructions displayed or enter [][2] to view trouble. The Trouble
light will turn off when the trouble is corrected.
AC Power - Indicates AC Power is present. The AC Power light will turn off when AC is absent.
Function Keys
Stay
Arms the system in Stay Mode.
Away
Arms the system in Away Mode (default).
Bypass
Same as pressing [][1] on the keypad.
Chime
Same as pressing [][4] on the keypad.
Exit
Same as pressing [][0] on the keypad.
Special Keys
Language Selection - Press and hold both buttons simultaneoudfsly for 2 seconds to activate. Scroll
to the desired language. Press [] to select choice.
Fire - Press and hold both buttons for 2 seconds to activate.
Auxiliary - Press and hold both buttons for 2 seconds to activate.
Panic - Press and hold both buttons for 2 seconds to activate.
16
These keys must be programmed by the installer
to function.
Keypad Keys, Indicators, and Commands (Continued)
User Commands
Press [] to select. Press [<][>] to scroll. Press [#] to exit.
PRESS...
To ...
Bypass Zones
Press [0][0]
Clear Bypass
Press [9][9]
Bypass Recall
Press [9][5]
Save Bypass
Press [9][1]
Recall Save
View System Troubles
Scroll to view all troubles
View Alarms in Memory
Scroll to view alarms
Chime ON/OFF
Turn chime on and off
Program User Codes
Change Attributes
Press [<][>]buttons to scroll to user code. Enter
[Master Code][9][xx] to enter the user code (xx = 1-16).
[1] Supervisor’s Code
[2] Duress Code
[3] Zone Bypassing
[4] Remote Access
[5]-[6] Future Use
[7] Bell/Siren Squawk Output
[8] One Time Use Code
User Commands
User Options
Event Buffer
System Test
Time and Date
System Service/DLS
User Call-up
Walk Test
Brightness Control
Buzzer Level Control
SMS Phone Numbers
Contrast Control
Late to Open
PGM Commands
If programmed by the installer, can be used to activate events such
as opening/closing garage doors.
Installer Programming
Requires a special code.
No-Entry Arming
The system will arm in Stay mode after the exit delay expires, the
entry delay is disabled.
Quick Arm/Quick Exit
Quick Arm is equivalent to entering your user code.
Quick Exit allows you to exit the premises without disarming the system.
17
23. Guidelines for Locating Smoke & CO Detectors
The following information is for general guidance only and it is recommended that local fire codes
and regulations be consulted when locating and installing smoke alarms and CO Alarms:
Smoke Detectors
Research has shown that all hostile fires in homes generate smoke to a greater or lesser extent.
Experiments with typical fires in homes indicate that detectable quantities of smoke precede detectable levels of heat in most cases. For these reasons, smoke alarms should be installed outside of each
sleeping area and on each storey of the home.
The following information is for general guidance only and it is recommended that local fire codes
and regulations be consulted when locating and installing smoke alarms.
It is recommended that additional smoke alarms beyond those required for minimum protection be
installed. Additional areas that should be protected include: the basement; bedrooms, especially
where smokers sleep; dining rooms; furnace and utility rooms; and any hallways not protected by the
required units.
On smooth ceilings, detectors may be spaced 9.1m (30 feet) apart as a guide. Other spacing may be
required depending on ceiling height, air movement, the presence of joists, uninsulated ceilings, etc.
Consult National Fire Alarm Code NFPA 72, CAN/ULC-S553-02 or other appropriate national standards for installation recommendations.
• Do not locate smoke detectors at the top of peaked or gabled ceilings; the dead air space in these
locations may prevent the unit from detecting smoke.
• Avoid areas with turbulent air flow, such as near doors, fans or windows. Rapid air movement around
the detector may prevent smoke from entering the unit.
• Do not locate detectors in areas of high humidity.
• Do not locate detectors in areas where the temperature rises above 38oC (100oF) or falls below 5oC
(41oF).
Smoke detectors should always be installed in USA in accordance with Chapter 11 of NFPA 72, the
National Fire Alarm Code: 11.5.1.1 Where required by applicable laws, codes, or standards for a specific
type of occupancy, approved single- and multiple-station smoke alarms shall be installed as follows:
(1) In all sleeping rooms and guest rooms.
(2) Outside of each separate dwelling unit sleeping area,
within 6.4 m (21 ft) of any door to a sleeping room, the distance measured along a path of travel.
(3) On every level of a dwelling unit, including basements.
(4) On every level of a residential board and care occupancy
(small facility), including basements and excluding crawl
spaces and unfinished attics.
(5) In the living area(s) of a guest suite.
(6) In the living area(s) of a residential board and care
occupancy (small facility).
Figure 1
Figure 3
Figure 3a
18
Figure 2
Figure 4
Carbon Monoxide Detectors
Carbon monoxide is colorless, odorless, tasteless, and very toxic. Carbon monoxide gas moves freely in
the air. The human body is most vulnerable to the effects of CO gas during sleeping hours. For maximum
protection, a CO alarm should be located outside primary sleeping areas or on each level of your home.
Figure 5 indicates the suggested locations in the home. The electronic sensor detects carbon monoxide,
measures the concentration and sounds a loud alarm before a potentially harmful level is reached.
Do NOT place the CO alarm in the following areas:
• Where the temperature may drop below -10°C or exceed 40°C
BEDROOM
• Near paint thinner fumes
• Within 5 feet (1.5 meter) of open flame appliances such as furBEDROOM
BEDROOM
naces, stoves and fireplaces
GARAGE
KITCHEN
GROUND
• In exhaust streams from gas engines, vents, flues or chimneys
FLOOR
• In close proximity to an automobile exhaust pipe; this will damBASEMENT
age the detector
PLEASE REFER TO THE CO DETECTOR INSTALLATION AND
OPERATING INSTRUCTION SHEET FOR SAFETY INSTRUCTIONS
AND EMERGENCY INFORMATION.
CARBON MONOXIDE DETECTOR
Figure 5
24. Household Fire Safety Audit
Read this section carefully for important information about fire safety.
Most fires occur in the home. To minimize this danger, we recommend that a household fire safety audit
be conducted and a fire escape plan be developed.
1. Are all electrical appliances and outlets in a safe condition? Check for frayed cords, overloaded lighting circuits, etc. If you are uncertain about the condition of your electrical appliances or household
service, have a professional evaluate these units.
2. Are all flammable liquids stored safely in closed containers in a well-ventilated cool area? Cleaning
with flammable liquids should be avoided.
3. Are fire-hazardous materials (e.g., matches) well out of reach of children?
4. Are furnaces and wood-burning appliances properly installed, clean and in good working order?
Have a professional evaluate these appliances.
25. Fire Escape Planning
There is often very little time between the detection of a fire and the time it becomes deadly. It is thus
very important that a family escape plan be developed and rehearsed.
1. Every family member should participate in developing the escape plan.
2. Study the possible escape routes from each location within the house. Since many fires occur at
night, special attention should be given to the escape routes from sleeping quarters.
3. Escape from a bedroom must be possible without opening the interior door.
NOTE: Consider the following when making your escape plans:
• Make sure that all border doors and windows are easily opened. Ensure that they are not painted
shut, and that their locking mechanisms operate smoothly.
• If opening or using the exit is too difficult for children, the elderly or handicapped, plans for rescue
should be developed. This includes making sure that those who are to perform the rescue can
promptly hear the fire warning signal.
• If the exit is above the ground level, an approved fire ladder or rope should be provided as well as
training in its use.
• Exits on the ground level should be kept clear. Be sure to remove snow from exterior patio doors in
winter; outdoor furniture or equipment should not block exits.
• Each person should know of a predetermined assembly point where everyone can be accounted for
(e.g. across the street or at a neighbor’s house). Once everyone is out of the building, call the Fire
Department.
• A good plan emphasizes quick escape. Do not investigate or attempt to fight the fire, and do not
gather belongings as this can waste valuable time. Once outside, do not re-enter the house. Wait for
the fire department.
• Write the fire escape plan down and rehearse it frequently so that should an emergency arise, everyone will know what to do. Revise the plan as conditions change, such as the number of people in the
home, or if there are changes to the building’s construction.
• Make sure your fire warning system is operational by conducting weekly tests. If you are unsure
about system operation, contact your installer.
• We recommend that you contact your local fire department and request further information on fire
safety and escape planning. If available, have your local fire prevention officer conduct an in-house
fire safety inspection.
19
IMPORTANT - READ CAREFULLY: DSC Software purchased with or without Products and Components
is copyrighted and is purchased under the following license terms:
• This End-User License Agreement (“EULA”) is a legal agreement
between You (the company, individual or entity who acquired the Software and any related Hardware) and Digital Security Controls, a division of Tyco Safety Products Canada Ltd. (“DSC”), the manufacturer
of the integrated security systems and the developer of the software
and any related products or components (“HARDWARE”) which You
acquired.
• If the DSC software product (“SOFTWARE PRODUCT” or “SOFTWARE”) is intended to be accompanied by HARDWARE, and is NOT
accompanied by new HARDWARE, You may not use, copy or install
the SOFTWARE PRODUCT. The SOFTWARE PRODUCT includes computer software, and may include associated media, printed materials,
and “online” or electronic documentation.
• Any software provided along with the SOFTWARE PRODUCT that is
associated with a separate end-user license agreement is licensed to
You under the terms of that license agreement.
• By installing, copying, downloading, storing, accessing or otherwise
using the SOFTWARE PRODUCT, You agree unconditionally to be
bound by the terms of this EULA, even if this EULA is deemed to be a
modification of any previous arrangement or contract. If You do not
agree to the terms of this EULA, DSC is unwilling to license the SOFTWARE PRODUCT to You, and You have no right to use it.
SOFTWARE PRODUCT LICENSE
The SOFTWARE PRODUCT is protected by copyright laws and
international copyright treaties, as well as other intellectual property
laws and treaties. The SOFTWARE PRODUCT is licensed, not sold.
1. GRANT OF LICENSE This EULA grants You the following rights:
(a) Software Installation and Use - For each license You acquire, You may have
only one copy of the SOFTWARE PRODUCT installed.
(b) Storage/Network Use - The SOFTWARE PRODUCT may not be installed,
accessed, displayed, run, shared or used concurrently on or from different
computers, including a workstation, terminal or other digital electronic device
(“Device”). In other words, if You have several workstations, You will have to
acquire a license for each workstation where the SOFTWARE will be used.
(c) Backup Copy - You may make back-up copies of the SOFTWARE
PRODUCT, but You may only have one copy per license installed at any
given time. You may use the back-up copy solely for archival purposes.
Except as expressly provided in this EULA, You may not otherwise make
copies of the SOFTWARE PRODUCT, including the printed materials
accompanying the SOFTWARE.
2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS
(a) Limitations on Reverse Engineering, Decompilation and Disassembly - You
may not reverse engineer, decompile, or disassemble the SOFTWARE
PRODUCT, except and only to the extent that such activity is expressly
permitted by applicable law notwithstanding this limitation. You may not
make any changes or modifications to the Software, without the written
permission of an officer of DSC. You may not remove any proprietary
notices, marks or labels from the Software Product. You shall institute
reasonable measures to ensure compliance with the terms and conditions of
this EULA.
(b) Separation of Components - The SOFTWARE PRODUCT is licensed as a
single product. Its component parts may not be separated for use on more
than one HARDWARE unit.
(c) Single INTEGRATED PRODUCT - If You acquired this SOFTWARE with
HARDWARE, then the SOFTWARE PRODUCT is licensed with the
HARDWARE as a single integrated product. In this case, the SOFTWARE
PRODUCT may only be used with the HARDWARE as set forth in this EULA.
(d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You
may not make it available to others or post it on a server or web site.
(e) Software Product Transfer - You may transfer all of Your rights under this
EULA only as part of a permanent sale or transfer of the HARDWARE, provided
You retain no copies, You transfer all of the SOFTWARE PRODUCT (including
all component parts, the media and printed materials, any upgrades and this
EULA), and provided the recipient agrees to the terms of this EULA. If the
SOFTWARE PRODUCT is an upgrade, any transfer must also include all prior
versions of the SOFTWARE PRODUCT.
(f) Termination - Without prejudice to any other rights, DSC may terminate this
EULA if You fail to comply with the terms and conditions of this EULA. In such
event, You must destroy all copies of the SOFTWARE PRODUCT and all of its
component parts.
(g) Trademarks - This EULA does not grant You any rights in connection with any
trademarks or service marks of DSC or its suppliers.
3. COPYRIGHT - All title and intellectual property rights in and to the
SOFTWARE PRODUCT (including but not limited to any images,
photographs, and text incorporated into the SOFTWARE PRODUCT), the
accompanying printed materials, and any copies of the SOFTWARE
PRODUCT, are owned by DSC or its suppliers. You may not copy the
printed materials accompanying the SOFTWARE PRODUCT. All title and
intellectual property rights in and to the content which may be accessed
through use of the SOFTWARE PRODUCT are the property of the
respective content owner and may be protected by applicable copyright
or other intellectual property laws and treaties. This EULA grants You no
rights to use such content. All rights not expressly granted under this
EULA are reserved by DSC and its suppliers.
4. EXPORT RESTRICTIONS - You agree that You will not export or
re-export the SOFTWARE PRODUCT to any country, person, or entity
subject to Canadian export restrictions.
5. CHOICE OF LAW - This Software License Agreement is governed by the
laws of the Province of Ontario, Canada.
6. ARBITRATION - All disputes arising in connection with this
Agreement shall be determined by final and binding arbitration in
accordance with the Arbitration Act, and the parties agree to be bound by
the arbitrator’s decision. The place of arbitration shall be Toronto,
Canada, and the language of the arbitration shall be English.
7. LIMITED WARRANTY
(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT
WARRANTY. DSC DOES NOT WARRANT THAT THE SOFTWARE WILL
MEET YOUR REQUIREMENTS OR THAT OPERATION OF THE
SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE.
(b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible for
problems caused by changes in the operating characteristics of the
HARDWARE, or for problems in the interaction of the SOFTWARE PRODUCT
with non-DSC-SOFTWARE or HARDWARE PRODUCTS.
(c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF
RISK - IN ANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR
CONDITIONS NOT STATED IN THIS LICENSE AGREEMENT, DSC’S
ENTIRE LIABILITY UNDER ANY PROVISION OF THIS LICENSE
AGREEMENT SHALL BE LIMITED TO THE GREATER OF THE
AMOUNT ACTUALLY PAID BY YOU TO LICENSE THE SOFTWARE
PRODUCT AND FIVE CANADIAN DOLLARS (CAD$5.00). BECAUSE
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
(d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE
ENTIRE WARRANTY AND SHALL BE IN LIEU OF ANY AND ALL
OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED
(INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE) AND OF ALL OTHER
OBLIGATIONS OR LIABILITIES ON THE PART OF DSC. DSC MAKES
NO OTHER WARRANTIES. DSC NEITHER ASSUMES NOR
AUTHORIZES ANY OTHER PERSON PURPORTING TO ACT ON ITS
BEHALF TO MODIFY OR TO CHANGE THIS WARRANTY, NOR TO
ASSUME FOR IT ANY OTHER WARRANTY OR LIABILITY
CONCERNING THIS SOFTWARE PRODUCT.
(e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NO
CIRCUMSTANCES SHALL DSC BE LIABLE FOR ANY SPECIAL, INCIDENTAL,
CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON BREACH OF
WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR
ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUT ARE NOT
LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFTWARE PRODUCT OR
ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE
OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES, DOWN TIME,
PURCHASERS TIME, THE CLAIMS OF THIRD PARTIES, INCLUDING
CUSTOMERS, AND INJURY TO PROPERTY.
WARNING: DSC recommends that the entire system be completely
tested on a regular basis. However, despite frequent testing, and due to,
but not limited to, criminal tampering or electrical disruption, it is
possible for this SOFTWARE PRODUCT to fail to perform as expected.
WARNING
Please Read Carefully
Not e t o In st a l l e rs
This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this
warning to the attention of the users of this system.
S ys t e m Fa i l u res
This system has been carefully designed to be as effective as possible.
There are circumstances, however, involving fire, burglary, or other
types of emergencies where it may not provide protection. Any alarm
system of any type may be compromised deliberately or may fail to
operate as expected for a variety of reasons. Some but not all of these
reasons may be:
• Inadequate Installation
A security system must be installed properly in order to provide adequate protection. Every installation should be evaluated by a security
professional to ensure that all access points and areas are covered. Locks
and latches on windows and doors must be secure and operate as
intended. Windows, doors, walls, ceilings and other building materials
must be of sufficient strength and construction to provide the level of
protection expected. A reevaluation must be done during and after any
construction activity. An evaluation by the fire and/or police department
is highly recommended if this service is available.
• Criminal Knowledge
This system contains security features which were known to be effective
at the time of manufacture. It is possible for persons with criminal intent
to develop techniques which reduce the effectiveness of these features.
It is important that a security system be reviewed periodically to ensure
that its features remain effective and that it be updated or replaced if it is
found that it does not provide the protection expected.
• Access by Intruders
Intruders may enter through an unprotected access point, circumvent a
sensing device, evade detection by moving through an area of insufficient coverage, disconnect a warning device, or interfere with or prevent
the proper operation of the system.
• Power Failure
Control units, intrusion detectors, smoke detectors and many other security devices require an adequate power supply for proper operation. If a
device operates from batteries, it is possible for the batteries to fail.
Even if the batteries have not failed, they must be charged, in good condition and installed correctly. If a device operates only by AC power,
any interruption, however brief, will render that device inoperative
while it does not have power. Power interruptions of any length are
often accompanied by voltage fluctuations which may damage electronic equipment such as a security system. After a power interruption
has occurred, immediately conduct a complete system test to ensure that
the system operates as intended.
• Failure of Replaceable Batteries
This system’s wireless transmitters have been designed to provide several years of battery life under normal conditions. The expected battery
life is a function of the device environment, usage and type. Ambient
conditions such as high humidity, high or low temperatures, or large
temperature fluctuations may reduce the expected battery life. While
each transmitting device has a low battery monitor which identifies
when the batteries need to be replaced, this monitor may fail to operate
as expected. Regular testing and maintenance will keep the system in
good operating condition.
• Compromise of Radio Frequency (Wireless) Devices
Signals may not reach the receiver under all circumstances which could
include metal objects placed on or near the radio path or deliberate jamming or other inadvertent radio signal interference.
• System Users
A user may not be able to operate a panic or emergency switch possibly
due to permanent or temporary physical disability, inability to reach the
device in time, or unfamiliarity with the correct operation. It is important that all system users be trained in the correct operation of the alarm
system and that they know how to respond when the system indicates an
alarm.
• Smoke Detectors
Smoke detectors that are a part of this system may not properly alert
occupants of a fire for a number of reasons, some of which follow. The
smoke detectors may have been improperly installed or positioned.
Smoke may not be able to reach the smoke detectors, such as when the
fire is in a chimney, walls or roofs, or on the other side of closed doors.
Smoke detectors may not detect smoke from fires on another level of
the residence or building.
Every fire is different in the amount of smoke produced and the rate of
burning. Smoke detectors cannot sense all types of fires equally well.
Smoke detectors may not provide timely warning of fires caused by
carelessness or safety hazards such as smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches or arson.
Even if the smoke detector operates as intended, there may be circumstances when there is insufficient warning to allow all occupants to
escape in time to avoid injury or death.
•
Motion Detectors
Motion detectors can only detect motion within the designated areas as
shown in their respective installation instructions. They cannot discriminate between intruders and intended occupants. Motion detectors do not
provide volumetric area protection. They have multiple beams of detection and motion can only be detected in unobstructed areas covered by
these beams. They cannot detect motion which occurs behind walls,
ceilings, floor, closed doors, glass partitions, glass doors or windows.
Any type of tampering whether intentional or unintentional such as
masking, painting, or spraying of any material on the lenses, mirrors,
windows or any other part of the detection system will impair its proper
operation.
Passive infrared motion detectors operate by sensing changes in temperature. However their effectiveness can be reduced when the ambient
temperature rises near or above body temperature or if there are intentional or unintentional sources of heat in or near the detection area.
Some of these heat sources could be heaters, radiators, stoves, barbecues, fireplaces, sunlight, steam vents, lighting and so on.
• Warning Devices
Warning devices such as sirens, bells, horns, or strobes may not warn
people or waken someone sleeping if there is an intervening wall or
door. If warning devices are located on a different level of the residence
or premise, then it is less likely that the occupants will be alerted or
awakened. Audible warning devices may be interfered with by other
noise sources such as stereos, radios, televisions, air conditioners or
other appliances, or passing traffic. Audible warning devices, however
loud, may not be heard by a hearing-impaired person.
• Telephone Lines
If telephone lines are used to transmit alarms, they may be out of service
or busy for certain periods of time. Also an intruder may cut the telephone line or defeat its operation by more sophisticated means which
may be difficult to detect.
• Insufficient Time
There may be circumstances when the system will operate as intended,
yet the occupants will not be protected from the emergency due to their
inability to respond to the warnings in a timely manner. If the system is
monitored, the response may not occur in time to protect the occupants
or their belongings.
• Component Failure
Although every effort has been made to make this system as reliable as
possible, the system may fail to function as intended due to the failure of
a component.
• Inadequate Testing
Most problems that would prevent an alarm system from operating as
intended can be found by regular testing and maintenance. The complete system should be tested weekly and immediately after a break-in,
an attempted break-in, a fire, a storm, an earthquake, an accident, or any
kind of construction activity inside or outside the premises. The testing
should include all sensing devices, keypads, consoles, alarm indicating
devices and any other operational devices that are part of the system.
• Security and Insurance
Regardless of its capabilities, an alarm system is not a substitute for
property or life insurance. An alarm system also is not a substitute for
property owners, renters, or other occupants to act prudently to prevent
or minimize the harmful effects of an emergency situation.
FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by
Digital Security Controls could void your authority to use this equipment.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
• Re-orient the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult a dealer or experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful: "How
to Identify and Resolve Radio/Television Interference Problems". This booklet is available from the U.S. Government Printing Office, Washington D.C.
20402, Stock # 004-000-00345-4.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules and, if the product
was approved July 23, 2001 or later, the requirements adopted by the ACTA.
On the top side of this equipment is a label that contains, among other information, a product identifier. If requested, this number must be provided to the
Telephone Company.
Product Identifier:
US:F53AL01B9057
USOC Jack:
RJ-31X
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular
plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be connected
to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areazs,
the sum of RENs should not exceed five (5.0). To be certain of the number of
devices that may be connected to a line, as determined by the total RENs, contact the local Telephone Company. For products approved after July 23, 2001,
the REN for this product is part of the product identifier that has the format
US: AAAEQ##TXXXX. The digits represented by ## are the REN without a
decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. REN = 0.1B
Incidence of Harm
If this equipment (SCW9055/SCW9057) causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical,
the Telephone Company will notify the customer as soon as possible. Also,
you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this
happens the Telephone Company will provide advance notice in order for you
to make necessary modifications to maintain uninterrupted service.
Equipment Maintenance Facility
If trouble is experienced with this equipment (SCW9055/SCW9057) for repair or warranty information, contact the facility indicated below. If the
equipment is causing harm to the telephone network, the Telephone Compa-
ny may request that you disconnect the equipment until the problem is solved.
This equipment is of a type that is not intended to be repaired by the end user.
DSC c/o APL Logistics 757 Douglas Hill Rd., Lithia Springs, GA 30122
Additional Information
Connection to party line service is subject to state tariffs. Contact the state
public utility commission, public service commission or corporation commission for information.
Alarm dialling equipment must be able to seize the telephone line and place
a call in an emergency situation. It must be able to do this even if other equipment (telephone, answering system, computer modem, etc.) already has the
telephone line in use. To do so, alarm dialling equipment must be connected
to a properly installed RJ-31X jack that is electrically in series with and ahead
of all other equipment attached to the same telephone line. Proper installation
is depicted in the figure below. If you have any questions concerning these
instructions, you should consult your telephone company or a qualified installer about installing the RJ-31X jack and alarm dialling equipment for you.
INDUSTRY CANADA STATEMENT
NOTICE: This product meets the applicable Industry Canada technical
specifications.
Le présent materiel est conforme aux specifications techniques applicables
d’Industrie Canada.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1.
L'indice d'équivalence de la sonnerie (IES) du présent matériel est de 0.1.
The Ringer Equivalence Number is an indication of the maximum number of
devices allowed to be connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five.
L’indice d’équivalence de la sonnerie (IES) sert à indiquer le nombre maximal
de terminaux qui peuvent être raccordés à une interface téléphonique. La terminaison d’une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la somme d’indices d’équivalence de la
sonnerie de tous les dispositifs n’excède pas 5.
The term ’IC:’ before the radio certification number only signifies that Industry
Canada technical specifications were met.
Certification Number IC: 160A-9057 (models SCW9055-433/SCW9057-433)
Certification Number IC: 160A-9057G (models SCW9055(D)(G)(SM)-433/
SCW9057(D)(G)(SM)-433)
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil
numérique de la classe B est conforme à la norme NMB-003 du Canada.
The SCW9055(X)-433 and SCW9057(X)-433 have been investigated by UL
and ULC and found in compliance with the listing requirements for Residential Fire and Burglary applications in accordance with the following standards:
UL985, UL1023, UL1635, ULC-S545 and ORD-C1023.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interferenlce that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada exempts de licence standard
RSS (s). Le fonctionnement est soumis aux deux conditions suivantes: (1) cet
appareil ne peut pas provoquer d'interférences et (2) cet appareil doit accepter
toute interférence, y compris les interférences qui peuvent causer un mauvais
fonctionnement de l' appareil.
This publication covers the following models:
• SCW9055-433/868
• SCW9057I-433/868
• WT4989
• WT8911
• SCW9057-433/868
• SCW9055G-433/868
• WT8989
• PT4
• SCW9055D-433/868
• SCW9057G-433/868
• WT4901
• PT8
• SCW9057D-433/868
• WT5500-433/868
• WT8901
• SCW9055I-433/868
• WT5500P-433/868
• WT4911
The 868 MHz models are not UL/ULC listed.
Only these models shall be used with UL/ULC listed systems: SCW9055-433, SCW9057-433, SCW9055G433, SCW9057G-433, WT5500-433, WT5500P-433, WT4901, WT4911, WT4989 and PT4. Only certain models of SCW9055/57 include the SMS features, check with your installer.
RN = 0.5
This DSC SCW9057-433
Security System may be
connected to the Telecom
Network.
This DSC SCW9055-433
Security System may be
connected to the Telecom
Network.
PTC 211/12/004
RN = 0.5
PTC 211/12/003
The following is a list of warnings applicable when this equipment is connected to the New Zealand
Telecom Network.
General Warning
The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted
that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a
different make or model, nor does it imply that any product is compatible with all of Telecom's network
services.
Reverse Numbering (decadic signalling)
Decadic signalling should not be used as it is being progressively phased out of the network. DTMF dialling is 100% available and it should always be used.
Line Grabbing Equipment
This equipment is set up to carry out test calls at pre-determined times. Such test calls will interrupt any
other calls that may be set up on the line at the same time. The timing set for such test calls should be discussed with the installer. The timing set for test calls from this equipment may be subject to 'drift'. If this
proves to be inconvenient and your calls are interrupted, then the problem of timing should be discussed
with the equipment installer. The matter should NOT be reported as a fault to Telecom Faults Service.
D.C. Line Feed to Other Devices
During dialling, this device unit does not provide DC voltage to the series port connection and this may
cause loss of memory functions for the terminal devices (local telephone) connected to T-1, R-1.
General Operation (ringer sensitivity and loading)
This device only responds to Distinctive Alert cadences DA1 and DA2.
In the event of any problem with this device, it is to be disconnected. A CPE item connected to one of
the device’s terminal ports may be connected directly in its place. The user should then arrange for the
product to be repaired. Should the matter be reported to Telecom as a wiring fault, and the fault is proven
to be due to this product, a call-out charge will be incurred.
© 2012 Tyco International Ltd. and its Respective Companies. All Rights Reserved.
Toronto, Canada • www.dsc.com • Printed in Canada
The trademarks, logos, and service marks displayed on this document are registered in the United States [or other countries]. Any misuse of
the trademarks is strictly prohibited and Tyco International Ltd. will aggressively enforce its intellectual property rights to the fullest extent of
the law, including pursuit of criminal prosecution wherever necessary. All trademarks not owned by Tyco International Ltd. are the property of
their respective owners, and are used with permission or allowed under applicable laws.
Product offerings and specifications are subject to change without notice. Actual products may vary from photos. Not all products include all
features. Availability varies by region; contact your sales representative.
">