Digital Security Controls SCW9055, SCW9057 wireless alarm system, WT4901, WT8901, WT4911, WT8911, WT4989, WT8989 wireless key, WT5500, WT5500P wireless keypad, PT4, PT8 prox tag User Manual

PDF

Документ

Self Contained Wireless Alarm System

SCW9055/SCW9057 v1.0 User Manual

DRAFT

WARNING:

This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer.

The entire manual should be carefully read.

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment.

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re-orient the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult a dealer or experienced radio/television technician for help.

The user may find the following booklet prepared by the FCC useful: "How to

Identify and Resolve Radio/Television Interference Problems". This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402,

Stock # 004-000-00345-4.

IMPORTANT INFORMATION

This equipment complies with Part 68 of the FCC Rules and, if the product was approved July 23, 2001 or later, the requirements adopted by the ACTA. On the top side of this equipment is a label that contains, among other information, a product identifier. If requested, this number must be provided to the Telephone

Company.

Product Identifier: US:F53AL01B9057

Equipment Maintenance Facility

If trouble is experienced with this equipment (SCW9055/SCW9057) for repair or warranty information, contact the facility indicated below. If the equipment is causing harm to the telephone network, the Telephone Company may request that you disconnect the equipment until the problem is solved. This equipment is of a type that is not intended to be repaired by the end user.

DSC c/o APL Logistics 757 Douglas Hill Rd., Lithia Springs, GA 30122

Additional Information

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.

Alarm dialling equipment must be able to seize the telephone line and place a call in an emergency situation. It must be able to do this even if other equipment

(telephone, answering system, computer modem, etc.) already has the telephone line in use. To do so, alarm dialling equipment must be connected to a properly installed RJ-31X jack that is electrically in series with and ahead of all other equipment attached to the same telephone line. Proper installation is depicted in the figure below. If you have any questions concerning these instructions, you should consult your telephone company or a qualified installer about installing the RJ-31X jack and alarm dialling equipment for you.

Network

Service

Provider's

Facilities

Telephone

Line

Customer Premises Equipment and Wiring

RJ-31X

Jack

Alarm Dialing

Equipment

Unused

RJ-11 Jack

Computer

Telephone

USOC Jack: RJ-31X

Telephone Connection Requirements

Fax Machine

Unused

RJ-11 Jack

Network

Demarcation

Point Telephone

A plug and jack used to connect this equipment to the premises wiring and teleAnswering

System

Telephone phone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is

INDUSTRY CANADA STATEMENT provided with this product. It is designed to be connected to a compatible mod-

NOTICE: This product meets the applicable Industry Canada technical specular jack that is also compliant. See installation instructions for details.

ifications.

Ringer Equivalence Number (REN)

Le présent materiel est conforme aux specifications techniques applicables d’In-

The REN is used to determine the number of devices that may be connected to dustrie Canada.

a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of

L'indice d'équivalence de la sonnerie (IES) du présent matériel est de 0.1.

RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local

Telephone Company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US: shown on the label. REN = 0.1B

Incidence of Harm

DRAFT the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the Telephone

Company will notify the customer as soon as possible. Also, you will be advised

The Ringer Equivalence Number is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five.

L’indice d’équivalence de la sonnerie

(IES) sert à indiquer le nombre maximal de terminaux qui peuvent être raccordés

à une interface téléphonique. La terminaison d’une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.

The term ’IC:’ before the radio certification number only signifies that Industry

Canada technical specifications were met.

Certification Number IC: 160A-9057 (models SCW9055-433/SCW9057-433) of your right to file a complaint with the FCC if you believe it is necessary.

The Ringer Equivalence Number (REN) for this terminal equipment is 0.1.

Certification Number IC: 160A-9057G (models SCW9055(D)(G)(SM)-433/

Changes in Telephone Company Equipment or Facilities

SCW9057(D)(G)(SM)-433)

The Telephone Company may make changes in its facilities, equipment, operaThis Class B digital apparatus complies with Canadian ICES-003.

tions or procedures that could affect the operation of the equipment. If this hapCet appareil numérique de la classe B est conforme à la norme NMB-003 du pens the Telephone Company will provide advance notice in order for you to Canada.

make necessary modifications to maintain uninterrupted service.

The SCW9055(X)-433 and SCW9057(X)-433 have been investigated by UL and

ULC and found in compliance with the listing requirements for Residential Fire and Burglary applications in accordance with the following standards: UL985,

UL1023, UL1635, ULC-S545 and ORD-C1023.

This publication covers the following models:

• SCW9055-433/868

• SCW9057-433/868

• SCW9055D-433/868

• SCW9057D-433/868

• SCW9055I-433/868

• SCW9057I-433/868

• SCW9055G-433/868

• SCW9057G-433/868

• SCW9055D-SM-433/868

• SCW9057D-SM-433/868

• SCW9055I-SM-433/868

• SCW9057I-SM-433/868

• SCW9055G-SM-433/868

• SCW9057G-SM-433/868

• WT5500-433/868

• WT5500P-433/868

• WT4989

• WT8989

• WT4901

• WT8901

• WT4911

• WT8911

• PT4

• PT8

NOTE: The 868 MHz models are not UL/ULC listed.

NOTE: Only these models shall be used with UL/ULC listed systems: SCW9055-433, SCW9057-433,

SCW9055G-433, SCW9057G-433, WT5500-433, WT5500P-433, WT4901, WT4911, WT4989 and that may cause undesired operation of the device.

PT4. Only certain models of SCW9055/57 include the SMS features, check with your installer.

Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). Le fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne peut pas provoquer d'interférences et (2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement de l' appareil.

About Your Security System 2

Fire Detection (must be enabled by Installer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Carbon Monoxide Detection (must be enabled by Installer) . . . . . . . . . . . . . . . . . . . . . . . . 2

Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

General System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Keypad Controls & Indicators 3

Language Selection

Arming and Disarming the System

Stay Arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Night Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Silent Exit Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Away Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Quick Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Siren Sounds After Away Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Remote Arming and Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Emergency Keys 5

When Alarm Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Intrusion (Burglary) Alarm Continuous Siren. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Fire Alarm Pulsed Siren 5

Carbon Monoxide Alarm (for future use, to be activated by your installer)

Audio Operation

2-Way/1-Way Audio Operation (SCW9057 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Two-Way Audio Operation Over GSM (SCW9057G only) . . . . . . . . . . . . . . . . . . . . . . . . . 6

Time & Date Programming

Bypassing Zones

Trouble Conditions

Alarm Memory

Door Chime 8

Access Code Programming 8

Access Codes [  ][5][Master Code] (when disarmed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

User Code Attributes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Inherent Attributes (all codes except installer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Zone Bypassing Attribute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Remote Access Attribute. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

DRAFT

Changing Brightness/Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Ambient Light Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Changing the Buzzer Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Viewing the Event Buffer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Changing Voice Dialer and SMS Phone Numbers 11

Late to Open

SMS (Short Message Service) Notification

The SMS Notification Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

SMS Remote Access Connection Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

On-board LCD SMS Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Two-Way Wireless Key (WT4989, WT8989) 13

Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

WT4989/WT8989 Status Display Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Keylock Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Testing Your System 14

Siren and Keypad Display Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Walk Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Allowing Computer Access to your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Reference Sheets 15

Access Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Sensor / Zone Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Voice Dialer and SMS Telephone Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Keypad Quick Guide

Guidelines for Locating Smoke & CO Detectors

Household Fire Safety Audit

Fire Escape Planning

21 i

Always ensure you obtain the latest version of the User Guide. Updated versions of this User

Guide are available by contacting your distributor.

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, electric shock and/or injury, observe the following:

• Do not spill any type of liquid on the equipment.

• Do not attempt to service this product yourself. Opening or removing the cover may expose you to dangerous voltage or other risk. Refer servicing to qualified service personnel. Never open the device yourself.

• Do not touch the equipment and its connected cables during an electrical storm; there may be a risk of electric shock from lightning.

• Do not use the Alarm System to report a gas leak if the system is near a leak.

REGULAR MAINTENANCE AND TROUBLESHOOTING

Keep your Alarm Controller in optimal condition by following all the instructions that are included within this manual and/or marked on the product.

CLEANING

• Clean the units by wiping with a damp cloth only.

• Do not use abrasives, thinners, solvents or aerosol cleaners (spray polish) that may enter through holes in the Alarm Controller and cause damage.

• Do not use any water or any other liquid.

• Do not wipe the front cover with alcohol.

TROUBLESHOOTING

Occasionally, you may have a problem with your Alarm Controller or telephone line. If this happens, your Alarm Controller will identify the problem and display an error message. Refer to the provided list when you see an error message on the display. If additional help is required, contact your distributor for service.

WARNING:

DRAFT experience necessary to be aware of hazards to which that person may be exposed in performing a task and of measures to minimize the risks to that person or other persons]. For EU and

Australian markets, the equipment is permanently connected; an accessible disconnect device shall be incorporated into the building installation wiring. For North America the equipment is using a direct plug-in connection; the socket outlet shall be installed near the SCW9055/57 and shall be easily accessible. The plug of the direct plug-in transformer serves as the disconnect device.

NOTE: There are no parts replaceable by the end-user within this equipment, except for the keypad batteries and the WT4901/8901, WT4989/8989 batteries.

WARNING:

Never obstruct the access to the socket-outlet to which this equipment is connected. These safety instructions should not prevent you from contacting the distributor and/or the manufacturer to obtain any further clarification and/or answers to your concerns.

About Your Security System

Read this manual carefully and have your installer instruct you on your system's operation and on which features have been implemented in your system. All users of this system should be fully instructed in its use. Fill out the "System Information" page with all of your zone information and access codes, and store this manual in a safe place for future reference.

NOTE: Please consult your installer for further information regarding the false alarm reduction features built into your system, as not all are covered in this manual.

Fire Detection (must be enabled by Installer)

This equipment is capable of monitoring fire detection devices such as smoke detectors and providing a warning if a fire condition is detected. Good fire detection depends on having an adequate number of detectors placed in appropriate locations. This equipment should be installed in accordance with NFPA 72 (N.F.P.A., Batterymarch Park, Quincy MA 02269). Please read the Family Escape Planning guidelines in this manual.

Carbon Monoxide Detection (must be enabled by Installer)

This equipment is capable of monitoring carbon monoxide detectors and providing a warning if carbon monoxide is detected. Please read the Family Escape Planning guidelines in this manual and instructions that are available with the carbon monoxide detector.

Testing

To ensure that your system continues to function as intended, you must test your system weekly.

Please refer to the "Testing your System" section in this manual. If your system does not function properly, call your installing company for service.

Monitoring

This system is capable of transmitting alarms, troubles, and emergency information to a central station. If you initiate an alarm by mistake, immediately call the central station to prevent an unnecessary response.

NOTE: The monitoring function must be enabled by the installer before it can become functional.

NOTE: This system has a communicator delay of 30 seconds. This function can be deleted, or

NOTE:

Maintenance

DRAFT

With normal use, the system requires minimum maintenance. Note the following points:

• Do not wash the security equipment with a wet cloth. Light dusting with a slightly moistened cloth should remove normal accumulations of dust.

• Replace the standby battery every 3-5 years.

NOTE: Do not attempt to replace the battery or open the enclosure; there is a risk of electric shock and/or fire.

• For other system devices such as smoke detectors, motion detectors, glassbreak detectors or door/window contacts, consult the manufacturer’s literature for testing and maintenance instructions.

General System Operation

Your security system comprises an integrated alarm control/keypad and various sensors and detectors. The keypad is mounted by the main entry/exit location. The system is self-contained; electronics and standby battery are housed within the keypad unit.

NOTE: Only the installer or service professional should have access to the system.

The security system has several zones of area protection. Each of these zones communicates to a single wireless sensor (motion detectors, glassbreak detectors, door contacts, etc.) or to one or more hard-wired sensors. A sensor in alarm is indicated by messages on the LCD.

Additional features include Automatic Inhibit (Swinger Shutdown) for Alarm; Tamper and Trouble signals after 3 occurrences in a given set period; SMS interactive operation*; and a Programmable Keypad Lockout option.

For SIA CP-01 classified installations, the swinger shutdown feature is programmed such that one or two trips will shut down the zone. The zone will be restored after a manual reset (by

entering the access code at the time of disarming the alarm system) or it will be reset automatically after 48 hours with no trips on any zones.

NOTE: (*) The SMS features was not investigated by UL/ULC.

Keypad Controls & Indicators

< > indicates user can scroll through options

2x16 LCD

Scroll Keys

Fire Key

Auxiliary Key

Panic Key *

7 8

Stay

Away

Chime

Bypass

Exit

LED Indicators

Ready

Armed

Trouble

Power

Function Keys

Stay

Away

Arm

Chime

Bypass Zones

Quick Exit

Selects Option

Previous Screen

IMPORTANT NOTICE

A security system cannot prevent emergencies. It is only intended to alert you and your central station (if applicable) to an emergency situation. Security systems are generally very reliable but they may not work under all conditions and they are not a substitute for prudent security practices or life and property insurance. Your security system must be installed and serviced by qualified security professionals. These professionals can instruct you on the level of protection that has been provided and on system operations.

NOTE:

DRAFT

Language Selection

Your system can display messages in different languages.

1. Press and hold both [<][>] buttons simultaneously for 2 seconds.

2. Using the [<][>] buttons, scroll through the available languages.

3. Press [  ] to select your desired language.

Arming and Disarming the System

Stay Arming

Stay arming will bypass the interior protection (i.e., motion sensors) and arm the perimeter of the system (i.e., doors and windows). Close all sensors (i.e., stop motion and close doors). The

Ready ( ) indicator will illuminate.

Press and hold the Stay button until it beeps (approx. 2 seconds. Enter your access code, do not leave the premises. During the setting state (Exit Delay active), the Armed ( ) and

Ready ( ) indicators will illuminate.

When the exit delay is completed, the alarm system is armed/set and this is indicated on the keypad as follows: the Ready ( ) indicator will turn off, the Armed ( ) indicator will remain on.

The Armed ( ) indicator and a bypass message will be displayed. The system will automatically ignore bypassed zones (i.e., motion sensors).

NOTE: Your installer can program a function key on the keypad to allow you to arm the system in Stay mode instantly. This allows you to activate Stay Arming by holding down the function key for 2 seconds. The system arms immediately with no beeps sounding and no exit delay. This feature must not be used in CP-01 installations.

NOTE: For SIA CP-01 listed panels, the Stay Arming Exit Delay will be twice as long as the Away

Arming Exit Delay.

NOTE: If your system is installed in accordance with SIA CP-01 Standard for False Alarm

Reduction, then the security system will arm in the Stay Armed mode if the exit delay time expires and no exit has been made.

Night Arming

To night arm the system when it has been armed in Stay mode, press [  ][1] at the keypad. All interior zones will now be armed except for devices programmed as Night zones.

NOTE: Your installer can also program a function key on the keypad to allow you to arm the system in Night mode. This allows Night arming to be activated by holding down the function key for 2 seconds.

Night zones are only armed in Away mode; this permits limited movement within the premises when the system is fully armed. Ensure that your installer has provided you with a list identifying zones programmed as night zones.

When the interior zones are activated (i.e., [  ][1]) you must enter your access code to disarm the system in order to gain access to interior areas that have not been programmed as night zones.

Silent Exit Delay

If the system is armed using the Stay button or using the "No Entry" Arming method ([  ][9]

[Access Code]), the keypad buzzer will be silenced and the exit time will be doubled for that exit period only. (CP-01 only)

Away Arming

Close all sensors (i.e., stop motion and close doors). The Ready ( ) indicator should be on.

To arm, press and hold the Away button for 2 seconds and/or enter your access code or press

[  ][0] to Quick Arm.

During the setting state (exit delay active) the Armed ( ) and Ready ( ) indicators will turn on, and the keypad will sound one beep per second. You now have ___ seconds to leave the prem-

DRAFT code.

When the exit delay is completed, the alarm system is armed and this is indicated on the keypad display as follows: the Ready ( ) indicator will turn off, the Armed ( ) indicator will remain on and the keypad will stop sounding.

NOTE: The system can also be armed/disarmed with a wireless key and with prox tags. Refer to the "Proximity Tags" and "Two-Way Wireless Key" sections for more details.

NOTE: If your system is installed in accordance with SIA CP-01 Standard for False Alarm

Reduction, the following holds true: Violation and restoral, followed by a second violation of the entry/exit zone before the end of the exit delay, will restart the exit delay.

Quick Exit

If the system is armed and you need to exit, use the Quick Exit function to avoid disarming and rearming the system. Press and hold the Quick Exit button for 2 seconds or press [  ][0].

You now have 2 minutes to leave the premises. When the door is closed again, the remaining exit time is cancelled.

Siren Sounds After Away Arming

Audible Exit Fault

In order to reduce false alarms, the Audible Exit Fault is designed to notify you of an improper exit when arming the system. If you fail to securely close the entry/exit door during the programmed exit delay period, the system will sound the alarm to indicate an improper exit (your installer will tell you if this feature has been enabled on your system). If this occurs:

1. Re-enter the premises.

2. Enter your access code before the entry delay timer expires, to disarm the system.

3. Repeat the Away arming procedure, ensuring that the entry/exit door(s) are secured.

Arming Error

An error tone will sound if the system is unable to arm. This will happen if the system is not ready to arm (i.e., sensors are open), or if an incorrect user code has been entered. If this happens, ensure all sensors are secure, press [ # ] and try again.

Disarming

To disarm an armed system (Armed ( ) indicator is On), enter your access code. If your keypad is in sleep mode, press any key to wake it up then enter your access code. The keypad will sound a continuous tone after the entry delay has been initiated by opening the entry/exit door.

Enter your code within _______ seconds to avoid an alarm condition (check with your installer to have this time programmed).

Disarming Error

If your code is invalid, the system will not disarm and a 2-second error tone will sound. If this happens, press [ # ] and try again.

Remote Arming and Disarming

The system can be armed and/or disarmed, if programmed by the installer, using a remote control device (wireless key). When arming the system using the Arm button on a wireless key, the system will acknowledge the command by sounding a single bell/siren squawk, if programmed to do so by the installer. When disarming using the Disarm button on a wireless key, the system will acknowledge the command by sounding two bell/siren squawks. Three squawks, when disarming with the

Disarm button, indicates that an alarm occurred while the system was armed. If you are unsure of the cause of the alarm, proceed with caution (see section on 2-way Wireless Keys).

Emergency Keys

Press BOTH (

Fire Auxiliary

), or (

Panic

) buttons for 2 seconds to generate a

Fire, Auxiliary, or Panic alarm. The keypad buzzer will beep indicating that the alarm input has been accepted and transmission to the central station is underway. The Fire buttons may or may not sound the siren depending on installer setup.

NOTE:

When Alarm Sounds

DRAFT

• Continuous Siren = Intrusion/Burglary Alarm

NOTE: The WT4911 siren will sound a dual frequency sweeping tone for burglary alarms.

• Temporal / Pulsed Siren = Fire Alarm

• 4 beeps, 5-second pause, 4 beeps = Carbon Monoxide alarm

NOTE: The priority of signals is fire alarm, carbon monoxide alarm then burglary alarm.

Intrusion (Burglary) Alarm Continuous Siren

If you are unsure of the source of the alarm, proceed with caution!

If the alarm was accidental, enter your access code to silence the alarm. If the alarm system is disarmed within the programmed Abort Window (check with the installer if this option has been enabled on your system and what is the transmitter delay time programmed), no alarm transmission to the Central Station will occur. Following the Abort Window there appears a 5-minute Cancel Window, during which a user can cancel, by entering their access code, an alarm that has been previously transmitted.

A cancel signal will be transmitted to the central station and the alarm system will also announce that the cancel signal was transmitted. Call your central station to avoid a dispatch.

Fire Alarm Pulsed Siren

Follow your emergency evacuation plan immediately!

If the fire alarm was accidental (burned toast, bathroom steam, etc.), enter your access code to silence the alarm. Call your central station to avoid a dispatch.

Carbon Monoxide Alarm

(must be enabled by your installer)

Activation of your CO alarm indicates the presence of carbon monoxide (CO), which can be fatal. During an alarm, the red LED on the CO detector flashes rapidly and buzzer sounds with a repeating cadence of: 4 quick beeps, 5-second pause, 4 quick beeps. If an alarm sounds:

1. Operate silence button.

2. Call emergency services or your fire department.

3. Immediately move outdoors or to an open door/window.

WARNING: Carefully review your Carbon Monoxide Installation/User Guide to determine the necessary actions required to ensure your safety and ensure that the equipment is operating correctly. Incorporate the steps outlined in the guide into your evacuation plan.

2-Way/1-Way Audio Operation (SCW9057 only)

If programmed by the installer, this feature allows the monitoring station to initiate a 2-way audio

(talk/listen) or 1-way audio (listen-in only) session when an alarm has been received. This feature is used to verify the nature of the alarm or determine the type of assistance required by the occupant.

NOTE: This feature can be initiated only by the monitoring station after an alarm has been received. The user can not initiate a 2-way audio session.

Time & Date Programming and Temperature Display

Press [  ][6] then enter your master access code to enter

HH:MM MM/DD/YY

09:06 01/31/10

User Functions. Use the [ < ][ > ] buttons to find the menu option, then press [  ] to select. Enter the time in 24-hr. format (HH:MM), followed by the date (MM:DD:YY). Press [#] to exit programming. If you are viewing a "Loss of Clock" trouble from within the trouble menu

([  ][2]), press [  ] to directly enter Date and Time programming (see Trouble Conditions).

The SCW9055/57 panel and WT5500 keypad can also display the outdoor temperature (Farenheit or Celsius) from the 2-way outdoor siren. This feature must be enabled by your installer.

NOTE: Your installer may have programmed your system to display the time and date while the keypad is idle. Press the [#] button to temporarily clear the date and time display if desired.

Bypassing Zones

Use the zone bypassing feature when you need access to a protected area while the system is armed, or when a zone is temporarily out of service but you need to arm the system. Bypassed zones will not be able to sound an alarm. As a result, bypassing zones reduces the level of

DRAFT cally cancelled each time the system is disarmed and must be bypassed again, if required, before the next arming.

With the system disarmed:

1. Press [  ] to enter the function menu. The keypad will display the screen on the right.

2. Press [1] or [  ].

Press (*) for <>

Zone Bypass

3. If your system is programmed to require access codes the screen on the right will be displayed. Enter your 4-digit access code.

4. Scroll to the desired zone number using the [ < ][ > ] keys, then press [  ] to select the zone or directly enter the 2-digit number of the zone you wish to bypass (e.g., 0 5 for zone 5).

Enter Your

Access Code

Scroll to <>

Bypass Zones

Activating All Bypassed Zones

To remove bypass (all zones):

1. Press [  ][1], then your access code.

2. Press [0][0].

3. To exit bypassing mode and return to the Ready state, press [#].

Recalling Bypassed Zones

To recall the last set of bypassed zones:

1. Press [  ][1], then your access code.

2. Press [9][9].

3. To exit bypassing mode and return to the Ready state, press [#].

Bypass Group

A Bypass Group is a selection of zones programmed into the system. If you bypass a group of zones on a regular basis, you can program them into a Bypass Group, so that you do not have to bypass each zone individually. Note that only one Bypass Group can be programmed at a time.

To program a Bypass Group:

1. Press [  ][1], then enter your access code.

2. Enter the 2-digit numbers (01-34) of the zones to be included in the Bypass Group or use the

[<][>] buttons to find the zone to be included in the Bypass Group, then press [  ] to select the zone.

3. To save the selected zone into the group, press [9][5].

4. To exit bypassing mode and return to the Ready state, press [#].

NOTE: If an access code is required to enter bypassing, only the master code and codes with

Supervisory enabled can set the Bypass Group.

To select a Bypass Group when arming the system:

1. Press [  ][1], then your access code.

2. Press [9][1]. The next time the system is armed, the zones in this group will be bypassed.

3. To exit bypassing mode and return to the Ready state, press [#].

NOTE: A Bypass Group is only recalled if the system is armed/disarmed after programming the

Bypass Group.

NOTE: This feature is not to be used in UL Listed installations.

Trouble Conditions

When a trouble condition is detected, the Trouble ( ) indicator will turn on and the keypad will beep every 10 seconds. Press the [#] button to silence the beeps. Press [  ][2] to view the trouble condition. The Trouble ( ) indicator will flash. Use the scroll [<][>] keys to view troubles.

Trouble

Alternate

Communicator Trouble

DRAFT

SMS Config Trouble. Press ual troubles.

[<][>] to scroll through individ-

Indicates Low Battery, System Trouble, System Tamper or RF

Jam detected.

Action

Call for service.

For Ethernet Trouble check LAN connections.

Call for service.

Service Required

(Press [1] for more information)

Loss of AC Power

Telephone Line Fault

Failure to

Communicate

Module/Sensor Fault

If the building and/or neighbourhood has lost electrical power, the system will continue to operate on battery power for several hours.

The system has detected that the telephone line is disconnected.

The system attempted to communicate with the monitoring station but failed. This may be due to a telephone line Fault.

Check AC connection.

Call for service.

The system is experiencing difficulties with one or more module/sensor on the system. Continue to press [5] to navigate through the zone, keypad, and siren fault menus.

Call for service.

Module/Sensor Tamper The system has detected a tamper condition with one or more module/sensor on the system. Continue to press [6] to navigate through the zone, keypad, and siren tamper menus.

Call for service.

Module/Sensor Low Battery

The system has detected a low battery condition with one or more module/sensor on the system. Continue to press [7] to display the zone(s), wireless key(s), keypad(s), siren(s) and prox tag(s).

See section on Siren

Test. Call for service.

Loss of Time & Date If complete power was lost (AC and Battery), the time and date will need to be re-programmed. Press [  ] .

Reprogram Time &

Date.

Trouble Comments Action

Blank Display/No

Response

Keypad battery may have discharged beyond the usable level.

Replace battery (call for service if trouble not cleared).

"Panel Response Not

Received" message

The keypad has lost wireless communication with the panel.

Occasional display of this message may be caused by local radio frequency interference.

If trouble persists, call for service.

Alarm Memory

When an alarm occurs, the Alarm Memory message will be displayed. To view which sensor(s) generated the alarm, press [  ][3].

For the system keypad use the scroll [<][>] buttons to view the sensors in alarm memory.

Press [#] to exit. To clear the memory, arm and disarm the system.

If an alarm sounded while armed, the system will automatically go to alarm memory when you disarm the system. In this instance, you should proceed with caution, as the intruder may still be within the building/premises.

Door Chime

To turn the door chime function on or off, press and hold the Chime button for 2 seconds or press [  ][4]. The system will sound 3 beeps to indicate the door chime is on, or one long tone to indicate that door chime is off.

Access Code Programming

In addition to the master code, you can program up to 16 additional user access codes.

To program User Access Codes:

1. Disarm your system, if it is armed.

2. Press [  ][5][Master Access Code (i.e., 4-digit or 6-digit code)]; the armed ( ) indicator will turn on.

3. Enter the 2-digit number to be programmed, this number is used to identify the User Access DRAFT

 ] to select.

4. Enter the new 4-digit or 6-digit access code. When programming is complete, enter another

2-digit code to program or press [#] to exit.

The access codes have programmable attributes which allow zone bypassing, duress, supervisor, remote access, or one-time use activation.

On WT5500P keypads, you will be prompted to swipe a prox tag once the last character of the access code is entered. To delete prox tags, the associated user access code must be deleted as described, then re-programmed if required.

NOTE: If wireless keys have been programmed then wireless key #1 will log as User Access Code

#1 (if that access code has been programmed). User Access Codes 1-16 will correspond to wireless keys or prox tags 1-16 .

NOTE: When using 6-digit access codes, the minimum number of variations of access codes are

58 823.

Access Codes — [



][5][Master Code] (when disarmed)

The [  ][5] User’s Programming command is used to program additional access codes (see

Access Code Programming).

User Codes - User codes 1-16 are available for the system.

Master Code (Access Code 40) - The master code has all of the attributes listed in the Programmable Attributes list below except for Duress (2) and One-Time Use (8) and is required to program all supervisor code attributes.

Supervisor Codes - These codes are always valid when entering the [  ][5] User Code Programming or [  ][6] User Function sections. However, these codes can only program additional codes which have equal or lesser attributes. Once programmed, the supervisor codes receive the master code’s attributes. These attributes are changeable. Any user code can be made a supervisor code by enabling User Code Attribute 1 (please see below for details).

Duress Codes - Duress codes are standard user codes that will transmit the Duress Alarm

Reporting Code whenever the code is entered to perform any function on the system. Any user code can be made a duress code by enabling User Code Attribute 2 (see below for details).

One-Time Use Code - This code permits temporary access to the system for a 24-hour time period. During the 24hr period, the temporary user may disarm the system once. There is no restriction on the number of times the temporary user may arm the system during the time period.

NOTE: Duress codes are not valid when entering [  ][5], [  ][6] or [  ][8] sections.

NOTE: Access codes cannot be programmed as a duplicate or as a “Code +/- 1”.

User Code Attributes

1. The default attributes of a new code will be the attributes of the code used to enter [  ][5] whether it is a new code or an existing code being programmed.

2. System Master (Code 40) has Attribute 3 on by default.

NOTE: These attributes are not changeable.

Inherent Attributes (all codes except installer)

Arm / Disarm - Any access code will be valid for arming and disarming the system.

Command Outputs ([  ][7][1] and [  ][7][2]) - If these outputs require access code entry, any access code is valid for performing the [  ][7][1-2][Access Code] functions on the system.

Programmable Attributes ([  ][5][Master/Supervisor Code][9][Code])

To program an access code attribute enter [  ][5][Master/Supervisor Code][9] then [<][>] scroll to the access code (e.g., 2-digit number 01-16) you want to program. Press [  ] to select the access code. Next, scroll [<][>] to the attribute you want to program and press [  ] (or enter the attribute #) to enable/disable the attribute.

# Attribute

1 Supervisor Code

# Attribute

5-6 For Future Use

2 Duress Code

3 Zone Bypassing Enabled

4 Phone Access

Bell/Siren Squawk upon Away Arming/Disarming

One-Time Use Code

This attribute allows the user to manually bypass zones if bypassing requires an access code.

Phone Access Attribute

This attribute allows the user to specify which user access codes can be used for remote access via SMS notification.

Bell/Siren Squawk Attribute

This attribute is used to determine whether an access code should generate an arming/disarming squawk when the away function key is pressed on a wireless key. Contact your installer to have this programmed. The Master code cannot use the Bell/Siren Squawk attribute, but the code is required to enable the Bell/Siren for other codes.

NOTE: This feature cannot prevent the Arm/Disarming squawks from being generated if an access code assigned to a wireless key is manually entered at a keypad.

Erasing an Access Code

To erase a code, select the code and enter [  ] as the first digit. If [  ] is entered, the system will delete the code (including the associated prox tag) immediately and the user will be returned to select another code.

Proximity Tag Enrollment (PT4/PT8)

Proximity (prox) tag readers are only available on WT5500P keypads. Refer to the label on top of the keypad to confirm which model you have.

Enrolling Proximity Tags

1. Enter [  ][5][Master Code] to enter User Code Programming.

2. Scroll to the desired user code (01-16, or 40 for the master code) then press [  ].

3. Enter your desired 4 or 6-digit user access code. The following message will be displayed after the user access code is entered:

Present Tag or

Press # to Exit

4. Place the prox tag near the tag reader ( ) at the left side of the display to assign it to the user code. The following message will be displayed:

Tag Enrolled

Successfully

5. If an attempt is made to assign a prox tag to an existing user code that has an associated prox tag, the following message will be displayed.

Duplicate

Tag/User Code

Select another user code or erase the existing user code and associated prox tag and re-enroll with the new prox tag. Return to Step 2 for instructions on how to enroll a user code.

NOTE: To exit the process at anytime, press [#].

Erasing a User Code/Proximity Tag

Enter [  ][5][Master Code], select the desired user code. Enter [  ] to erase the code and associated prox tag. The keypad will display the user number (e.g., 01) with a letter “P” if a user code has already been programmed and a letter “T” if a code and prox tag have been programmed.

NOTE:

Proximity Tag Operation

DRAFT

6. Place the prox tag near the tag reader ( ) at the left side of the display to arm/disarm your system. When arming the system, the following message will be displayed:

Exit Delay in

Progress

7. When disarming the system, the following message will be displayed:

System Disarmed

8. If there is an attempt to swipe a prox tag that has not been enrolled, an error tone will sound and the following message will be displayed:

Invalid Tag

Return to Step1 for instructions on how to enroll the prox tag.

WARNING: KEEP THE PROXIMITY TAG OUT OF REACH OF SMALL CHILDREN.

THE MATERIALS ASSOCIATED WITH THIS PRODUCT (LITHIUM BATTERIES, ETC.) MUST BE RECY-

CLED ACCORDING TO LOCAL RULES AND REGULATIONS.

User Function Commands

Disarm the system then enter [  ][6][Master Code]. The [  ][6] command is used to gain access to the following list of Master functions of the system:

[1] Time and Date - Enter 4 digits for 24hr System Time (HH-MM). Valid entries are 00-23 for the hour and 00-59 for minutes. Enter 6 digits for the Month, Day and Year (MM-DD-YY).

[2]-[3] For Future Use.

[4] System Test - The system tests siren output: on-board siren – 4 seconds (2 seconds medium volume, 2 seconds high volume), indoor/outdoor siren – 2 seconds. Keypad lights, back-up battery pack and communicator are tested.

[5] Enable DLS / Allow Remote System Service - If enabled, the installer can to access

Installer Programming remotely using DLS (Downloading Software). This function provides a window for telephone ring detection by the alarm system. The DLS window will remain open for

6 hours, during which time the installer will be able to enter DLS an unlimited number of times.

After the 6-hr window has expired, access to programming via DLS will be unavailable until the window is re-opened.

[6] User Call-up - If enabled by the installer, the panel will make 1 attempt to call the downloading computer. The downloading computer must be waiting for the panel to call before downloading can be performed.

[7] For Future Use.

[8] User Walk Test - Allows the user to enter the Walk Test mode. See Walk Test on page 16.

[9] Late to Open Enable/Disable - This function enables or disables the Late to Open time programmed in [0].

[0] Late to Open Time of Day - This function is used to program the time setting enabled in [9].

NOTE: Refer to "Late to Open" section for details.

Changing Brightness/Contrast

When this option is selected, the keypad will allow you to scroll through 4 brightness levels and

10 contrast levels.

1. Press [ 

DRAFT

3. Press [  ] to select the setting you want to adjust.

4. a) Brightness Control: There are 4 backlighting levels. Use the [<][>] buttons to scroll to the desired level.

b) Contrast Control: There are 10 different display contrast levels. Use the [<][>] buttons to scroll to the desired contrast level.

5. To exit, press [#].

Ambient Light Sensor

During battery operation, the keypad uses the ambient light sensor ( ) to automatically adjust the backlighting brightness levels to conserve battery life. This function may be disabled by your installer.

Changing the Buzzer Level

When this option is selected, the keypad will allow you to scroll through 21 different buzzer levels. A level of 00 disables the buzzer.

1. Press [  ][6] [Master Code].

2. Use the [<][>] buttons to scroll to Buzzer Control, then press [  ] to select.

3. There are 21 levels; use the [<][>] buttons to scroll to the desired level. Press [#] to exit.

Viewing the Event Buffer

The event buffer will show you a list of the last 500 events that have occurred on your system.

1. Press [  ][6][Master Code].

2. To select Event Buffer viewing, press [  ].

3. The keypad will display the event number and the time and date. Press [  ] to switch between this information and the event details.

4. Use the [<][>] buttons to scroll through the events in the buffer.

5. To exit event buffer viewing, press [#].

Changing SMS Phone Numbers

This section tells you how to program your SMS phone numbers:

1. Enter [  ][6][Master Code] to enter the Master User Functions of the system.

2. Use the [<][>] buttons to scroll to the SMS programming prompt.

Select Option <>

SMS Programming

3. Press [  ] to select the SMS phone numbers or to see your GSM phone number. The following message is displayed:

Press (  ) for <>

Phone No.1 P

“P” denotes whether the phone number has been programmed.

• To see your

GSM phone number use the [<][>]

buttons to scroll to the following message.

Then press

[  ] to

view the number.

Press (  ) for <>

GSM Phone No.

Pressing (  ) here shows your GSM number.

4. Press , to select Phone No. 1. The following 26-digit phone number screen is shown.

X=1 to 8 to indicate the phone number screen DFFFFFFFFFFFFFFF being programmed.

(e.g., X=1 for Phone No. 1)

•

FFFFFFFFFFFFPH#X

5. Program a new phone number or delete an existing phone number as follows:

DRAFT

FFFFFFFFFFFFPH#1

Do Not delete the remaining F’s.

• To Delete an existing phone number , replace the letter D with an F by pressing [  ][6][  ] and then press # to exit. This will delete the phone number.

F4168889999FFFFF

FFFFFFFFFFFFPH#1

6. Use the [<][>] buttons to scroll to another Phone No. to be programmed.

7. Repeat from Step 4 to enter more phone numbers. To exit the process at anytime, press [#].

Late to Open

This feature allows a user to be notified if their alarm system is not disarmed by a programmed time of day.

NOTE: The Late to Open feature requires the monitoring station to forward calls to the user. Verify with the installer whether this function is active.

[9] Late to Open Enable/Disable

The Late to Open feature enables or disables the Late to Open time programmed in [0].

It is typically used to track children after school. For example, if the parents get home from work at 5pm, and a child gets home at 4 p.m. The programmable timer could be set for 4:15 p.m. If the system is not disarmed at this time an alert would be sent to the monitoring station.

The keypad will display "Late to Open is Enabled" and sound 3 beeps if [9] is pressed within the User Functions menu when this feature is off. The LCD keypad will display "Late to Open is Disabled" and sound an error tone if [9] is pressed within the User Functions menu when this feature is on.

[0] Late to Open Time of Day

This function is used to program the time setting enabled in [9]. This function programs the

"Late to Open" time of day for all 7 days of the week.

• Valid entries for these sections are 00:00 – 23:59.

• Entering 99:99 will disable the Late to Open feature for the current day.

• After entering [  ][6][Master Code][0], beeps will be sounded and "Press (  ) for < > Sunday" will be displayed on the keypad.

• Pressing the right scroll [>] button displays the days of the week, from Sunday to Saturday.

While in the Late to Open menu, entering keys 1-7 will also select each day from Sunday to

Saturday, respectively.

• If [  ] is pressed to select a day of the week, no beeps will be sounded and the keypad will display "Set 24hr Time" "Enter HH:MM 9999". If [#] is pressed from this menu, the user will be DRAFT

SMS (Short Message Service) Notification

SMS Notification occurs when the control panel sends a text message to the user for each system event that occurs. These text messages are limited to 32 characters.

NOTE: SMS Notification is not available in North America.

Interactive SMS allows the user to send a text message (in one of 28 languages, depending on

SMS Interactive language selection) to the control panel and perform a set of functions on the panel. There are 12 pre-defined text message commands available that the user can send to the control panel. Please refer to the SMS Reference Card to find the text used for other languages.

NOTE: Interactive SMS is available in North America.

The SMS Notification Sequence

The panel will send an SMS notification for every event that the panel can communicate. SMS notification messages are programmed by your installer from the keypad or by using DLS IV.

Text messages can be programmed in the language of your choice.

There are 8 SMS phone numbers available to support SMS messages. An SMS phone number can be changed using [*][6][Master Code]. Refer to the Changing SMS Phone Numbers section for detailed instructions.

SMS Remote Access Connection Sequence

This feature allows you to control your security system remotely via SMS.

1. Determine which action to perform remotely on the panel. Please refer to the SMS Reference card for details on how to enter the text required.

All SMS remote access functions require an access code, with the exception of the help function. The following list is an example of the functions available.

Function

• stay arm • activate command output 2

• away arm • deactivate command output 1

• disarm

• unbypass

• activate command output 1 • help (list of available commands)

NOTE: you by your installer.

• deactivate command output 2 DRAFT

2. Compose an SMS message that consists of the function text, a space, and your 4-digit or 6digit access code (e.g., “Stay arm”(Function)<space>“2234”(Access Code )) and send it to your GSM phone number .

3. The panel matches the incoming phone number to one of the phone numbers in its SMS phone number list.

4. The panel verifies the contents of the SMS message and performs the action.

5. When the action is completed, the panel sends an SMS message containing “function successful” back to the user. If the function or access code is invalid, the response will include

“function unsuccessful” in the SMS message.

6. A one hour System Lockout is caused by entering 5 invalid access codes. If you receive the message “function failed,” the system has locked you out and you must wait one hour before using SMS remote access, again.

On-board LCD Display SMS Messages

In addition to function commands, you can also send general SMS messages from your mobile phone that can be displayed on your keypad screen. A 10-second steady tone will sound when it appears on the keypad display. This message is displayed until you press any button to clear. The number of key presses required to remove the message is programmed by your installer.

Two-Way Wireless Key (WT4989, WT8989)

The two-way wireless key communicates directly with the control panel, performing many of the functions that a wireless keypad performs. Please refer to the WT4989/8989 operating instructions for more information.

The WT4989 and WT8989 has 4 function keys programmable for 6 functions each, an LCD icon display that can display system status using a combination of 7 icons and an internal buzzer.

Unless custom programmed by your installer the functions are as follows:

Function Keys

Status Request - Press this button for 1 second to view the control panel system status via the LCD display icons.

Stay Arming - Press to arm your system in Stay mode. All perimeter zones are active but interior zones remain inactive.

Away Arming Press to arm your system. Interior and exterior zones will be armed.

Disarm Press to disarm your system.

Panic Alarm Press & hold for 3 seconds to create a panic alarm on the security system.

* Command Output 1 - Press & hold both buttons at the same time for 3 seconds to activate the assigned output.

* Command Output 2 - Press & hold both buttons at the same time for 3 seconds to activate the assigned output.

WT4989/WT8989 Status Display Icons

The table below summarizes the status that can be shown by the WT4989/WT8989 LCD:

ICON (S=Steady, F=Flashing)

(

)

System Trouble

(F) Keylock Enable

(S) Disarmed

(S) Alarm in Memory

DRAFT

(S) Away - Armed

(S) Stay - Armed

(F) [  ][9] Armed - Stay

(F) [  ][9] Armed - Night

(S) Night - Armed (S) Low Battery

(F) Critical Low Battery

Buzzer

Provides an audible confirmation of a pressed button or that a command to the panel has been executed.

Keylock Mode

Ensures that the system is not accidently armed or disarmed by the wireless key.

To lock the keys:

1. Press and hold the Status and Away keys simultaneously for 3 seconds.

2. After 3 seconds, the wireless key will beep and flash the keylock icon ( the keys are locked.

) to indicate that

To unlock the keys:

1. Press and hold the Status and Away keys simultaneously for 3 seconds.

NOTE: Pressing the Panic key for 3 seconds will also exit Keylock mode.

2. Upon exiting Keylock mode, the status will be automatically displayed.

Testing Your System

NOTE: Inform your Monitoring Station when you begin and end system testing.

Household fire alarm systems shall be tested by a qualified service technician at least every 3 years in accordance with NFPA72.

It is the user’s responsibility to test the system weekly (excluding smoke detectors). Ensure you follow all the steps in the two tests below.

NOTE: Should the system fail to function properly, call your installer immediately for service.

Siren and Keypad Display Test

The test activates all display pixels and indicator lights on the keypad and does a 4-second check of the siren.

1. Press [  ][6][Master Code][4].

The following will occur:

- The system activates the siren output for 2 seconds followed by full volume alarm for 2 seconds. All display lights and LCD pixels will turn on.

- The Ready, Armed, Trouble and Power LED’s will flash for the duration of the test.

2. To exit the function menu, press [#].

Keypad Low Battery

The flashing trouble icon on a keypad will indicate that keypad has a low battery.

Mo u nting

Hole s

Keypad Battery Replacement

1. Slide the keypad up and out from the mounting plate/desk stand (removing the screws first if required). The bay for the four AA batteries is open and visible at the back of the keypad.

T a mper

S witch

B a tterie s

Pl u g

Wire

Ch a nnel

2. Insert the batteries as directed on the back of the keypad. Ensure the correct polarity is observed.

desk stand.

DRAFT

To determine which siren has a low battery press and hold the test button, located at the front of the siren, for 5 seconds.

Mo u nting

Hole s

• If the siren sounds for 4 seconds, the batteries are good.

• If the siren doesn’t sound, the batteries are low.

WT4901/WT8901 Siren Battery Replacement

• Open the front cover and remove old batteries. Once the old batteries are removed, wait 30 seconds before inserting the replacement batteries.

• Install new batteries as shown in the polarity indicated by the engraving. If the batteries are installed incorrectly, in the reverse polarity, the indoor siren will not work. With typical use, the

WT4901/WT8901 batteries should be replaced every two years.

NOTE: Only use Energizer (4) 1.5V AA alkaline batteries (WT5500, WT4901/WT8901).

DO NOT TRY TO RECHARGE THESE BATTERIES. DISPOSAL OF USED BATTERIES MUST BE

MADE IN ACCORDANCE WITH THE WASTE RECOVERY AND RECYCLING REGULATIONS IN

YOUR AREA.

Walk Test

Walk Test mode allows you to test the operation of each detector in the system. While in Walk Test mode, the Ready, Armed, and Trouble LED's will flash to indicate that the Walk Test is active. The

Walk Test can be terminated at anytime by re-entering [  ][6] [Master Code][8] on the keypad. The system will also automatically terminate the Walk Test on completion; it will sound an audible warning (5 beeps every 10 seconds), beginning 5 minutes before the termination of the test.

1. Before testing, ensure that the system is disarmed and the Ready light is on.

2. Press [#] and close all zones to return the system to the Ready state.

3. Perform a System Test by following the steps in the previous section.

4. Press [  ][6][Master Code][8] to initiate the Walk Test.

5. To test the zones, activate each detector in turn (e.g., open each door/window or walk in motion detector areas).

The System will display the following message when each zone (detector) is activated: "Secure

System Before Arming < >", or "Secure or Arm System". Use the [<][>] buttons to view which zones are open. The message will disappear when the zones are closed.

Allowing Computer Access to your System

Occasionally, your installer may need to send information to or retrieve information from your security system. Your installer will do this by having a computer call your system. You may need to prepare your system to receive this ‘downloading" call. To do this:

Press [  ][6][Master Code][5] at the keypad. This allows downloading for a limited period of time. During this time, the system will answer incoming downloading calls. For more information on this feature, please ask your installer.

DRAFT

Reference Sheets

Fill out the following information for future reference and store this guide in a safe place.

System Information

Enabled?



FIRE



AUXILIARY



PANIC

The Exit Delay Time is _______ seconds.

The Entry Delay Time is _______ seconds.

For Service

Central Station Information:

Account#: ___________________ Telephone#: __________________

Installer Information:

Company: ___________________ Telephone#: __________________

If you suspect a false alarm signal has been sent to the central monitoring station, call the station to avoid an unnecessary response.

Battery Installation / Service Date:

________________________

Access Codes

Master Code [40]: ______________________ Proximity Tag: 

Code

Wireless

Key



Prox

Tag

DRAFT

09 

Tag

 

Access Code



Sensor / Zone Information

Sensor Protected Area Sensor Type

Sensor Protected Area

Sensor Type

Site Identification Message:

GSM Phone Number:

SMS



Phone Number #

SMS



Phone Number

Keypad Quick Guide

The following table summarizes the keys, indicators, and most often used commands of the keypad.

Keypad Keys, Indicators, and Commands

Status Lights

Ready - must be on to arm system. All zones must be secured or bypassed and the system disarmed for this light to activate.

Armed - indicates system is armed. If the Ready light and the Armed light are both on it indicates an Exit Delay is in progress.

Trouble - On indicates a system malfunction or tamper. Flashing indicates that the keypad has a low battery condition. Follow the instructions displayed or enter [  ][2] to view trouble.

The Trouble light will turn off when the trouble is corrected.

AC Power - indicates AC Power is present. The AC Power light will turn off when AC is absent.

Stay

Away

Bypass

Chime

Exit

Function Keys

Arms the system in Stay Mode.

Arms the system in Away Mode (default).

Same as pressing [  ][1] on the keypad.

Same as pressing [  ][4] on the keypad.

Same as pressing [  ][0] on the keypad.

Special Keys

DRAFT

Auxiliary - Press and hold both buttons for 2 seconds to activate.

Panic - Press and hold both buttons for 2 seconds to activate.

These keys must be programmed by the installer to function.

User Commands

Press [  ] to select, press [<][>] to scroll, press [#] to exit.

PRESS...

To ...

Bypass Zones

Press [0][0]

Press [9][9]

Press [9][5]

Press [9][1]

View System Troubles

Clear Bypass

Bypass Recall

Save Bypass

Recall Save

Scroll to view all troubles

View Alarms in Memory Scroll to view alarms ,

, Chime ON/OFF Turn chime on and off

, Program User Codes

Change Attributes

Press [<][>]buttons to scroll to user code. Enter

[Master Code][9][xx] to enter the user code (xx = 1-16).

[1] Supervisor’s Code

[2] Duress Code

[3] Zone Bypassing

[4] Remote Access

[5]-[6] Future Use

[7] Bell/Siren Squawk Output

[8] One Time Use Code

Keypad Keys, Indicators, and Commands (Continued)

User Options

PGM Commands

Installer Programming

User Commands

Event Buffer

System Test

Time and Date

System Service/DLS

User Call-up

Walk Test

Brightness Control

Buzzer Level Control

SMS Phone Numbers

Contrast Control

Late to Open

If programmed by the installer, can be used to activate events such as opening/closing garage doors.

Requires a special code.

No-Entry Arming

Quick Arm/Quick Exit

The system will arm in Stay mode after the exit delay expires, the entry delay is disabled.

Quick Arm is equivalent to entering your user code.

Quick Exit allows you to exit the premises without disarming the system.

Guidelines for Locating Smoke & CO Detectors

The following information is for general guidance only and it is recommended that local fire codes and regulations be consulted when locating and installing smoke alarms and CO Alarms:

Smoke Detectors

Research has shown that all hostile fires in homes generate smoke to a greater or lesser extent.

Experiments with typical fires in homes indicate that detectable quantities of smoke precede detectable levels of heat in most cases. For these reasons, smoke alarms should be installed outside of each sleeping area and on each storey of the home.

DRAFT cially where smokers sleep; dining rooms; furnace and utility rooms; and any hallways not protected by the required units.

On smooth ceilings, detectors may be spaced 9.1m (30 feet) apart as a guide. Other spacing may be required depending on ceiling height, air movement, the presence of joists, uninsulated ceilings, etc. Consult National Fire Alarm Code NFPA 72, CAN/ULC-S553-02 or other appropriate national standards for installation recommendations.

• Do not locate smoke detectors at the top of peaked or gabled ceilings; the dead air space in these locations may prevent the unit from detecting smoke.

• Avoid areas with turbulent air flow, such as near doors, fans or windows. Rapid air movement around the detector may prevent smoke from entering the unit.

• Do not locate detectors in areas of high humidity.

• Do not locate detectors in areas where the temperature rises above 38 o

C (100 o

F) or falls below 5 o

C (41 o

F).

Smoke detectors should always be installed in USA in accordance with Chapter 11 of NFPA 72, the National Fire Alarm Code: 11.5.1.1 Where required by applicable laws, codes, or standards for a specific type of occupancy, approved single- and multiple-station smoke alarms shall be installed as follows:

( 1) In all sleeping rooms and guest rooms.

(2) Outside of each separate dwelling unit sleeping area, within 6.4 m (21 ft) of any door to a sleeping room, the distance measured along a path of travel.

(3) On every level of a dwelling unit, including basements.

(4) On every level of a residential board and care occupancy (small facility), including basements and excluding crawl spaces and unfinished attics.

(5) In the living area(s) of a guest suite.

(6) In the living area(s) of a residential board and care occupancy (small facility).

Fi g ure 1 Fi g ure 2

Fi g ure 3 a Fi g ure 4

Fi g ure 3

Carbon Monoxide Detectors

Carbon monoxide is colorless, odorless, tasteless, and very toxic. Carbon monoxide gas moves freely in the air. Suggested locations are in or as near as possible to sleeping areas of the home.

DRAFT potentially harmful level is reached.

Do NOT place the CO alarm in the following areas:

• Where the temperature may drop below -10°C or exceed 40°C

• Near paint thinner fumes

BEDROOM

BEDROOM BEDROOM

• Within 5 feet (1.5 meter) of open flame appliances such as furnaces, stoves and fireplaces

GROUND

FLOOR

KITCHEN GARAGE

• In exhaust streams from gas engines, vents, flues or chimneys

BASEMENT

• In close proximity to an automobile exhaust pipe; this will damage the detector

CARBON MONOXIDE DETECTOR

Fi g ure 5

WARNING: PLEASE REFER TO THE CO DETECTOR INSTALLATION AND OPERATING IN-

STRUCTION SHEET FOR SAFETY INSTRUCTIONS AND EMERGENCY INFORMATION.

Household Fire Safety Audit

Read this section carefully for important information about fire safety.

Most fires occur in the home. To minimize this danger, we recommend that a household fire safety audit be conducted and a fire escape plan be developed.

1. Are all electrical appliances and outlets in a safe condition? Check for frayed cords, overloaded lighting circuits, etc. If you are uncertain about the condition of your electrical appliances or household service, have a professional evaluate these units.

2. Are all flammable liquids stored safely in closed containers in a well-ventilated cool area?

Cleaning with flammable liquids should be avoided.

3. Are fire-hazardous materials (e.g., matches) well out of reach of children?

4. Are furnaces and wood-burning appliances properly installed, clean and in good working order? Have a professional evaluate these appliances.

Fire Escape Planning

There is often very little time between the detection of a fire and the time it becomes deadly. It is thus very important that a family escape plan be developed and rehearsed.

1. Every family member should participate in developing the escape plan.

2. Study the possible escape routes from each location within the house. Since many fires occur at night, special attention should be given to the escape routes from sleeping quarters.

3. Escape from a bedroom must be possible without opening the interior door.

NOTE: Consider the following when making your escape plans:

• Make sure that all border doors and windows are easily opened. Ensure that they are not painted shut, and that their locking mechanisms operate smoothly.

• If opening or using the exit is too difficult for children, the elderly or handicapped, plans for rescue should be developed. This includes making sure that those who are to perform the rescue can promptly hear the fire warning signal.

well as training in its use.

DRAFT

• Each person should know of a predetermined assembly point where everyone can be accounted for (e.g. across the street or at a neighbor’s house). Once everyone is out of the building, call the Fire Department.

• A good plan emphasizes quick escape. Do not investigate or attempt to fight the fire, and do not gather belongings as this can waste valuable time. Once outside, do not re-enter the house. Wait for the fire department.

• Write the fire escape plan down and rehearse it frequently so that should an emergency arise, everyone will know what to do. Revise the plan as conditions change, such as the number of people in the home, or if there are changes to the building’s construction.

• Make sure your fire warning system is operational by conducting weekly tests. If you are unsure about system operation, contact your installer.

• We recommend that you contact your local fire department and request further information on fire safety and escape planning. If available, have your local fire prevention officer conduct an in-house fire safety inspection.

IMPORTANT - READ CAREFULLY: DSC Software purchased with or without Products and Components is copyrighted and is purchased under the following license terms:

• This End-User License Agreement (“EULA”) is a legal agreement between You (the company, individual or entity who acquired the Software and any related Hardware) and Digital Security Controls, a division of Tyco Safety Products Canada Ltd. (“DSC”), the manufacturer of the integrated security systems and the developer of the software and any related products or components (“HARDWARE”) which You acquired.

• If the DSC software product (“SOFTWARE PRODUCT” or “SOFT-

WARE”) is intended to be accompanied by HARDWARE, and is NOT accompanied by new HARDWARE, You may not use, copy or install the SOFTWARE PRODUCT. The SOFTWARE PRODUCT includes computer software, and may include associated media, printed materials, and “online” or electronic documentation.

• Any software provided along with the SOFTWARE PRODUCT that is associated with a separate end-user license agreement is licensed to

You under the terms of that license agreement.

(f) Termination - Without prejudice to any other rights, DSC may terminate this

EULA if You fail to comply with the terms and conditions of this EULA. In such event, You must destroy all copies of the SOFTWARE PRODUCT and all of its component parts.

(g) Trademarks - This EULA does not grant You any rights in connection with any trademarks or service marks of DSC or its suppliers.

3. COPYRIGHT - All title and intellectual property rights in and to the

SOFTWARE PRODUCT (including but not limited to any images, photographs, and text incorporated into the SOFTWARE PRODUCT), the accompanying printed materials, and any copies of the SOFTWARE

PRODUCT, are owned by DSC or its suppliers. You may not copy the printed materials accompanying the SOFTWARE PRODUCT. All title and intellectual property rights in and to the content which may be accessed through use of the SOFTWARE PRODUCT are the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and treaties. This EULA grants You no rights to use such content. All rights not expressly granted under this

EULA are reserved by DSC and its suppliers.

• By installing, copying, downloading, storing, accessing or otherwise using the SOFTWARE PRODUCT, You agree unconditionally to be bound by the terms of this EULA, even if this EULA is deemed to be a modification of any previous arrangement or contract. If You do not agree to the terms of this EULA, DSC is unwilling to license the SOFT-

WARE PRODUCT to You, and You have no right to use it.

SOFTWARE PRODUCT LICENSE

The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. The SOFTWARE PRODUCT is licensed, not sold.

1. GRANT OF LICENSE This EULA grants You the following rights:

(a) Software Installation and Use - For each license You acquire, You may have only one copy of the SOFTWARE PRODUCT installed.

(b) Storage/Network Use - The SOFTWARE PRODUCT may not be installed, accessed, displayed, run, shared or used concurrently on or from different computers, including a workstation, terminal or other digital electronic device

(“Device”). In other words, if You have several workstations, You will have to acquire a license for each workstation where the SOFTWARE will be used.

PRODUCT, but You may only have one copy per license installed at any given time. You may use the back-up copy solely for archival purposes.

Except as expressly provided in this EULA, You may not otherwise make copies of the SOFTWARE PRODUCT, including the printed materials accompanying the SOFTWARE.

2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS

(a) Limitations on Reverse Engineering, Decompilation and Disassembly - You may not reverse engineer, decompile, or disassemble the SOFTWARE

PRODUCT, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation. You may not make any changes or modifications to the Software, without the written permission of an officer of DSC. You may not remove any proprietary notices, marks or labels from the Software Product. You shall institute reasonable measures to ensure compliance with the terms and conditions of this EULA.

(b) Separation of Components - The SOFTWARE PRODUCT is licensed as a single product. Its component parts may not be separated for use on more than one HARDWARE unit.

HARDWARE, then the SOFTWARE PRODUCT is licensed with the

HARDWARE as a single integrated product. In this case, the SOFTWARE

PRODUCT may only be used with the HARDWARE as set forth in this EULA.

(d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You may not make it available to others or post it on a server or web site.

(e) Software Product Transfer - You may transfer all of Your rights under this

EULA only as part of a permanent sale or transfer of the HARDWARE, provided

You retain no copies, You transfer all of the SOFTWARE PRODUCT (including all component parts, the media and printed materials, any upgrades and this

EULA), and provided the recipient agrees to the terms of this EULA. If the

SOFTWARE PRODUCT is an upgrade, any transfer must also include all prior versions of the SOFTWARE PRODUCT.

4. EXPORT RESTRICTIONS - You agree that You will not export or re-export the SOFTWARE PRODUCT to any country, person, or entity subject to Canadian export restrictions.

5. CHOICE OF LAW This Software License Agreement is governed by the laws of the Province of Ontario, Canada.

6. ARBITRATION All disputes arising in connection with this

Agreement shall be determined by final and binding arbitration in accordance with the Arbitration Act, and the parties agree to be bound by the arbitrator’s decision. The place of arbitration shall be Toronto,

Canada, and the language of the arbitration shall be English.

7. LIMITED WARRANTY

(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT

WARRANTY. DSC DOES NOT WARRANT THAT THE SOFTWARE WILL

MEET YOUR REQUIREMENTS OR THAT OPERATION OF THE

SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE.

(b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible for problems caused by changes in the operating characteristics of the

HARDWARE, or for problems in the interaction of the SOFTWARE PRODUCT with non-DSC-SOFTWARE or HARDWARE PRODUCTS.

RISK - IN ANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR

CONDITIONS NOT STATED IN THIS LICENSE AGREEMENT, DSC’S

ENTIRE LIABILITY UNDER ANY PROVISION OF THIS LICENSE

AGREEMENT SHALL BE LIMITED TO THE GREATER OF THE

AMOUNT ACTUALLY PAID BY YOU TO LICENSE THE SOFTWARE

PRODUCT AND FIVE CANADIAN DOLLARS (CAD$5.00). BECAUSE

SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR

LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL

DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

(d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE

ENTIRE WARRANTY AND SHALL BE IN LIEU OF ANY AND ALL

OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED

(INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE) AND OF ALL OTHER

OBLIGATIONS OR LIABILITIES ON THE PART OF DSC. DSC MAKES

NO OTHER WARRANTIES. DSC NEITHER ASSUMES NOR

AUTHORIZES ANY OTHER PERSON PURPORTING TO ACT ON ITS

BEHALF TO MODIFY OR TO CHANGE THIS WARRANTY, NOR TO

ASSUME FOR IT ANY OTHER WARRANTY OR LIABILITY

CONCERNING THIS SOFTWARE PRODUCT.

(e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NO

CIRCUMSTANCES SHALL DSC BE LIABLE FOR ANY SPECIAL, INCIDENTAL,

CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON BREACH OF

WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR

ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUT ARE NOT

LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFTWARE PRODUCT OR

ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE

OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES, DOWN TIME,

PURCHASERS TIME, THE CLAIMS OF THIRD PARTIES, INCLUDING

CUSTOMERS, AND INJURY TO PROPERTY.

WARNING: DSC recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this SOFTWARE PRODUCT to fail to perform as expected.

WARNING

Please Read Carefully

•

Motion Detectors

N o t e t o I n s ta l l e r s

This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this warning to the attention of the users of this system.

S y s t e m F a i l u r e s

This system has been carefully designed to be as effective as possible.

There are circumstances, however, involving fire, burglary, or other types of emergencies where it may not provide protection. Any alarm system of any type may be compromised deliberately or may fail to operate as expected for a variety of reasons. Some but not all of these reasons may be:

•

Inadequate Installation

Motion detectors can only detect motion within the designated areas as shown in their respective installation instructions. They cannot discriminate between intruders and intended occupants. Motion detectors do not provide volumetric area protection. They have multiple beams of detection and motion can only be detected in unobstructed areas covered by these beams. They cannot detect motion which occurs behind walls, ceilings, floor, closed doors, glass partitions, glass doors or windows.

Any type of tampering whether intentional or unintentional such as masking, painting, or spraying of any material on the lenses, mirrors, windows or any other part of the detection system will impair its proper operation.

A security system must be installed properly in order to provide adequate protection. Every installation should be evaluated by a security professional to ensure that all access points and areas are covered. Locks and latches on windows and doors must be secure and operate as intended. Windows, doors, walls, ceilings and other building materials must be of sufficient strength and construction to provide the level of protection expected. A reevaluation must be done during and after any construction activity. An evaluation by the fire and/or police department is highly recommended if this service is available.

•

Criminal Knowledge

Passive infrared motion detectors operate by sensing changes in temperature. However their effectiveness can be reduced when the ambient temperature rises near or above body temperature or if there are intentional or unintentional sources of heat in or near the detection area.

Some of these heat sources could be heaters, radiators, stoves, barbecues, fireplaces, sunlight, steam vents, lighting and so on.

•

Warning Devices

This system contains security features which were known to be effective at the time of manufacture. It is possible for persons with criminal intent to develop techniques which reduce the effectiveness of these features.

It is important that a security system be reviewed periodically to ensure that its features remain effective and that it be updated or replaced if it is found that it does not provide the protection expected.

Warning devices such as sirens, bells, horns, or strobes may not warn people or waken someone sleeping if there is an intervening wall or door. If warning devices are located on a different level of the residence or premise, then it is less likely that the occupants will be alerted or awakened. Audible warning devices may be interfered with by other noise sources such as stereos, radios, televisions, air conditioners or other appliances, or passing traffic. Audible warning devices, however loud, may not be heard by a hearing-impaired person.

•

Telephone Lines

•

Access by Intruders

If telephone lines are used to transmit alarms, they may be out of service or busy for certain periods of time. Also an intruder may cut the telephone line or defeat its operation by more sophisticated means which may be difficult to detect.

Intruders may enter through an unprotected access point, circumvent a sensing device, evade detection by moving through an area of insufficient coverage, disconnect a warning device, or interfere with or prevent the proper operation of the system.

•

Insufficient Time

•

Power Failure

Control units, intrusion detectors, smoke detectors and many other security devices require an adequate power supply for proper operation. If a device operates from batteries, it is possible for the batteries to fail.

Even if the batteries have not failed, they must be charged, in good con-

There may be circumstances when the system will operate as intended, yet the occupants will not be protected from the emergency due to their inability to respond to the warnings in a timely manner. If the system is monitored, the response may not occur in time to protect the occupants or their belongings.

dition and installed correctly. If a device operates only by AC power, •

Component Failure any interruption, however brief, will render that device inoperative

Although every effort has been made to make this system as reliable as while it does not have power. Power interruptions of any length are often accompanied by voltage fluctuations which may damage electronic equipment such as a security system. After a power interruption has occurred, immediately conduct a complete system test to ensure that the system operates as intended.

•

Failure of Replaceable Batteries

DRAFT conditions such as high humidity, high or low temperatures, or large temperature fluctuations may reduce the expected battery life. While each transmitting device has a low battery monitor which identifies possible, the system may fail to function as intended due to the failure of a component.

•

Inadequate Testing

Most problems that would prevent an alarm system from operating as intended can be found by regular testing and maintenance. The complete system should be tested weekly and immediately after a break-in, an attempted break-in, a fire, a storm, an earthquake, an accident, or any kind of construction activity inside or outside the premises. The testing should include all sensing devices, keypads, consoles, alarm indicating devices and any other operational devices that are part of the system.

•

Security and Insurance when the batteries need to be replaced, this monitor may fail to operate

Regardless of its capabilities, an alarm system is not a substitute for as expected. Regular testing and maintenance will keep the system in property or life insurance. An alarm system also is not a substitute for good operating condition.

property owners, renters, or other occupants to act prudently to prevent

•

Compromise of Radio Frequency (Wireless) Devices or minimize the harmful effects of an emergency situation.

Signals may not reach the receiver under all circumstances which could include metal objects placed on or near the radio path or deliberate jamming or other inadvertent radio signal interference.

•

System Users

A user may not be able to operate a panic or emergency switch possibly due to permanent or temporary physical disability, inability to reach the device in time, or unfamiliarity with the correct operation. It is important that all system users be trained in the correct operation of the alarm system and that they know how to respond when the system indicates an alarm.

•

Smoke Detectors

Smoke detectors that are a part of this system may not properly alert occupants of a fire for a number of reasons, some of which follow. The smoke detectors may have been improperly installed or positioned.

Smoke may not be able to reach the smoke detectors, such as when the fire is in a chimney, walls or roofs, or on the other side of closed doors.

Smoke detectors may not detect smoke from fires on another level of the residence or building.

Every fire is different in the amount of smoke produced and the rate of burning. Smoke detectors cannot sense all types of fires equally well.

Smoke detectors may not provide timely warning of fires caused by carelessness or safety hazards such as smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches or arson.

Even if the smoke detector operates as intended, there may be circumstances when there is insufficient warning to allow all occupants to escape in time to avoid injury or death.

DRAFT

Toronto, Canada • www.dsc.com • Printed in Canada

The trademarks, logos, and service marks displayed on this document are registered in the United States [or other countries]. Any misuse of the trademarks is strictly prohibited and Tyco International Ltd. will aggressively enforce its intellectual property rights to the fullest extent of the law, including pursuit of criminal prosecution wherever necessary. All trademarks not owned by Tyco International Ltd. are the property of their respective owners, and are used with permission or allowed under applicable laws.

Product offerings and specifications are subject to change without notice. Actual products may vary from photos. Not all products include all features. Availability varies by region; contact your sales representative.

2 9 0 0 7 8 2 7 R0 0 1

Здравейте! Аз съм AI чатбот, специално обучен да ви помага с Digital Security Controls SCW9055. Прегледах обстойно документа и мога да ви помогна да намерите точната информация, която ви е необходима, или да обясня съдържанието на ясен и прост език. Независимо дали търсите насоки за конкретни функции, стъпки за отстраняване на неизправности или обща употреба, не се колебайте да задавате въпросите си. Колкото повече подробности предоставите за вашите притеснения или нужди, толкова по-точно и ефективно мога да ви помогна!

Асистентът пише

Асистентът не е на клавиатурата. Моля, опитайте отново по-късно.

Изглежда, че сте достигнали документ, който е написан на няколко езика, включително и такъв, който не е вашият роден език. Можете да използвате следните връзки, за да скриете временно страници без езика, който предпочитате.