Ronix 4554 Manual

GASOLINE BRUSH CUTTER
4554
SPECIFICATIONS
Engine model
1E44F-5
Engine power
51.7cc
Rated output power
1.35kw/7500rpm
Carburetor
Diaphragm type
Ignition
CDI
Shaft diameter
26mm
Shaft type
whole shaft
Transmission shaft
9 teeth
Fuel tank capacity
900ml
Gross Weight
10.5 Kgs
Net weight
9.5 Kgs
Accessories
Double shoulder harness,
Trimmer head, 3T blade,
Tools kit bag, Mix pot
PARTS LIST
Control handle
Tube
String head/metal blade
Trigger
Switch
Lock trigger
Engine
Spark plug
Air Filter
Handle
Upper clamp
Guard
Left handle
Fuel tank
USER MANUAL
1
INTENDED USE
This production is only used for cutting grass, bush, arbore scent shrub
and clumps. Any other of use the brush cutter unmentioned in this
manual could involve danger for your personal
NOTE:
Before using this product, please read this manual carefully to understand
the proper use of your unit.
INTRODUCTION
This manual contains safety information to make you aware of the
hazards and risks associated with the machine and how to avoid them.
This machine is intended for trimming and brush cutting. It is important
that you read and understand these instructions thoroughly before
attempting to start or operate this equipment. Save these instructions
for future reference.
SYMBOLE
Because a Brush cutter is high-speed, fast cutting power tool, special
safety precaution must be observed to reduce the risk of personal injury.
Read this manual carefully. Be familiar with the controls and the proper
use of the unit. Know how to shut it off, and how to unhook a unit quickly.
Wear appropriate hearing and eye protection while operating this
machine.
Wear anti-vibration, thick and slip-resistant work gloves
Wear security and slip-resistant footwear
Read operator’s instruction book before operating this machine
and follow all warnings and safety instructions
2
GASOLINE BRUSH CUTTER
Check the condition of working area to avoid any accident by hitting
hidden obstacles such as stumps, stones, cans, or broken glass
Beware of blade thrust
Beware of thrown objects
Keep bystanders at least 15m away from the operating person
Do not use saw blades! Never modify the cutter in any way. Improper
use of any cutter can cause SERIOUS OR FATAL PERSONAL INJURY
Guaranteed sound power level according to noise directive
2000/14/EC and 2005/88/EC: 113 dB(A) The engine uses two-stroke
fuel, a mixture of gasoline and 2-stroke lubricant 40:1
The safety alert symbol is used to identify safety information about
hazards that can result in personal injury. A signal word (DANGER,
WARNING, or CAUTION) is used with the alert symbol to indicate the
likelihood and the potential severity of injury.
DANGER
Indicates a hazard which, if not avoided, will result in death or serious
injury
WARNING
Indicates a hazard which, if not avoided, could result in death or serious
injury
CAUTION
Indicates a hazard which, if not avoided, could result in minor or
moderate injury
USER MANUAL
3
NOTICE
Indicates a situation that could result in damage to the product
SAFETY RULES & PRECAUTIONS
Proper safety precautions must be observed. Like all power equipment
this unit must be handled carefully. DO NOT EXPOSE YOURSELF
OR OTHERS TO DANGER. Follow these general rules. Do not permit
others to use this machine unless they are thoroughly responsible and
have read, and understand the machine manual and are trained in its
operation.
Always wear safety goggles or visor for eye protection. Dress properly,
do not wear loose clothing or jewelry that could become caught in moving
parts of the unit. Safe, sturdy, nonskid footwear should always be worn.
Long hair should be tied back. It is recommended that legs and feet be
covered to protect from flying debris during operation.
Use the anti-vibration (AV) glove.
Keep the AV system well maintained. An unbalanced blade or trimmer due
to excess wear will increase cutting time and the vibrations transmitted
to your hands. A machine with loose components or with damaged or
worn AV buffers will also tend to have higher vibration levels. All the
above mentioned precautions do not guarantee that you will not sustain
white finger disease or carpal tunnel syndrome. Therefore, continual
and regular users should monitor closely the condition of their hands
fingers.
If any of the above symptoms appear, seek medical advice immediately.
- Inspect the entire machine for loose parts (nuts, bolts, screws, etc.) and
any damage. Repair or replace as necessary before using the machine.
DO NOT USE any attachment with this power head other than the
ones recommended by our company. Serious injury to the operator or
bystanders could result as well as damage to the machine.
- The blade guard and front handle guard is very important to the
machine. It must be screwed up on the machine before the initial use.
4
GASOLINE BRUSH CUTTER
These guards must always be fixed when operating the machine. Check
these guards before each use. If any damage (crack, break, etc.) on the
guard, contact with your dealer for replacing it.
If use of non-conformant replacement guards, or remove or modify
these guards could result in serious injury to the operator or bystanders.
- Keep the handles free from oil and fuel.
- Always use proper handles and shoulder strap when cutting.
- Do not smoke while mixing fuel or filling tank.
- Do not mix fuel in an enclosed room or near open flames. Assure
adequate ventilation.
- Always mix and store the fuel in a properly marked container that is
approved by local codes and ordinances for such usage.
- Never remove the fuel tank cap while the engine is running.
- Never start or run the engine inside a closed room or building. Exhaust
gas contain dangerous carbon monoxide.
- Never attempt to make engine adjustments while the unit is running
and strapped to the operator. Always make engine adjustments with the
unit resting on a flat, clear surface.
- Do not use the unit if it is damaged or poorly adjusted. Never remove
the machine’s guard.
- Inspect the area to be cut and remove all debris that could become
entangled in the nylon cutting head. Also remove any objects that the
unit may throw during cutting.
- Keep children away. Onlookers should be kept at a safe distance from
the work area, at least 15 METER (50 FEET)
- Never leave the machine unattended.
- Do not use this unit for any job other than those for which it is intended
as described in this manual.
- Do not overreach. Keep proper footing and balance at all times. Do not
run the unit while standing on a ladder or on any other unstable footing
location. Appropriately use the harness provided when operating the
machine.
- Keep hands and feet clear of the nylon cutting head or blade while unit
USER MANUAL
5
is in use.
- Do not use this type of machine for sweeping away debris.
- Do not use the unit when you are tired, ill or under the influence of
medication, drugs or alcohol.
- Use nylon cutting head which is free of damage. If a stone or any other
obstacle is hit, stop the engine and check the nylon cutting head. A
broken or unbalanced nylon cutting head must never be used.
FOLLOW INSTRUCTION FOR CHANGING
ACCESSORIES
- Do not store in a closed area where fuel vapors can reach an open flame
from hot water heaters, furnaces, etc. Store in a locked, well-ventilated
area only.
- Ensure safe and proper performance of your product. These parts
are available from your dealer. The use of any other accessories or
attachments may cause a potential hazard or injury to the user, damage
to the machine.
- Clean the machine completely, especially, the fuel tank, its surroundings,
and the air cleaner.
- When refueling, be sure to stop the engine and confirm that it is cooled
down. Never refuel when the engine is running or hot. When gasoline
spills, be sure to wipe it up completely dispose of those materials before
starting the engine.
- Stay clear of other workers or bystanders by at least 15 meters/50 feet.
- Whenever approaching an operator of the machine, carefully call his
attention and confirm that the operator stop the engine. Be careful not
to startle or distract the operator which can cause an unsafe situation.
- Never touch the nylon cutting head or blade when ever the engine is
running. If it is necessary to replace the protector or cutting attachment,
be sure to stop the engine and confirm that the cutting device has
stopped running.
- The engine should be turned off when the machine is moved between
work areas.
6
GASOLINE BRUSH CUTTER
- Be careful not to hit the nylon cutting head against stones, or the
ground.
Unreasonable rough operation will shorten the life of the machine as
well as create an unsafe environment for yourself and those around you.
- Pay attention to loosening and overheating of parts. If there is any
abnormality of the machine, stop operation immediately and check
the machine carefully. If necessary, have the machine serviced by an
authorized dealer. Never continue to operate a machine which may be
malfunctioning.
- In start-up or during operation of the engine, never touch hot parts
such as the muffler, the high voltage wire or the spark plug.
- After the engine has stopped, the muffler is still hot. Never place the
machine in any places where there are flammable materials (dry grass,
etc.), combustible gasses or combustible liquids.
- Pay special attention to operation in the rain or just after the rain as the
ground may be slippery.
- If you slip or fall to the ground or into a hole, release the throttle lever
immediately.
- Be careful not to drop the machine or hit it against obstacles.
- Before proceeding to adjust or repair the machine, be sure to stop the
engine and detach the spark plug.
- When the machine is placed in storage for a long time, drain fuel from
the fuel tank and carburetor, clean the parts, move the machine to a
safe place and confirm that the engine is cooled down.
- Make daily inspection before use and after dropping or other impacts
to identify significant damage or defects to assure safe and efficient
operation. For a thorough inspection of your machine, please contact
the dealer.
- Keep the machine away from fire or sparks.
- It is believed that a condition called Raynaud’s phenomenon, which
affects the fingers of certain individuals may be brought about by
exposure to vibration and cold. Loss of color and numbness in the
fingers. The following precautions are strongly recommended because
USER MANUAL
7
the minimum exposure which might trigger the ailment is unknown.
Keep your body warm, especially the head, neck, feet, ankles, hands
and wrists.
Maintain good blood circulation by performing vigorous arm exercises
during frequent work breaks and also by not smoking.
Limit the hours of operation. Try to fill each day with jobs where operating
the brush cutter or other hand-held power equipment is not required.
If you experience discomfort, redness and swelling of the fingers followed
by whitening and loss of feeling, consult your physician before further
exposing yourself to cold and vibration.
- Always wear ear protection, loud noise for long time can make hearing
debase even lost hearing.
- Total face and head protection must be wearing to prevent damage
from plummet or branch.
- Wear no-slip heavy duty work gloves to improve your grip on the brush
cutter handle. Gloves also reduce the transmission of machine vibration
to your hands.
WARNING
The cutter area is still dangerous while the machine is coasting to a stop
ASSEMBLY INSTRUCTION
.
INSTALLING HANDLE
Installing “D” handle
1
8
GASOLINE BRUSH CUTTER
2
3
Refer to the pic 1~3, loose and take off the 4 screw and the upper clamp,
Install the handle in to the middle clamp, then locked the screw
.
INSTALLING PLASTIC GUARD
1, Move the 2 screw from the guard
2, Aim at the thread hole with the clamp and guard
3, Tighten the screw
Guard
Clamp
Screw
.INSTALLING HARNESS
1, Adjust the harness hanger in a comfortable piston.
2, Buckle the harness at the hanger
.REPLACE THE METAL BLADE TO STRING HEAD
.DISASSEMBLY METAL BLADE
1, Align the hole on the gear box to the slot on the flange washer
2, Use pin to through the hole and slot and hold the flange washer
3, loose the nut and remove the metal blade and cup washer
.ASSEMBLY STRING HEAD
4, Install the flange washer and cup washer on the spline shaft.
5, Align the hole on the gear box to the slot on the flange washer.
6, Use pin to through the hole and slot and hold the flange washer.
7, Install the string head and tighten it.
USER MANUAL
9
USE THE DOUBLE-SHOULDER HARNESS
.
INSTALL THE HARNESS
Put the harness on your shoulders and position the snap joint on front of
your waist and connect the snap joint.
.SPREAD THE LOAD ON YOUR SHOULDERS
Tension the side straps so that the weight is evenly distributed across
both shoulders.
.CORRECT HEIGHT
Adjust the hanger position so that the unit can hang on correct position.
.HOOK INSTALLATION
Attach the belt hook to the hook on the pipe to control the weight of the
machine with the help of the belt and
Keep the device
WARNING & CAUTION
.EXCESSIVE VIBRATION
STOP ENGINE IMMEDIATELY
Excessive vibration of blade means that it is not properly installed-stop
engine immediately and check blade. Blade not properly installed will
cause injury.
10
GASOLINE BRUSH CUTTER
RULES FOR SAFE OPERATION
WARNING!
All models trimmers and brush cutters can throw small stone, metal or
small objects as well as the material being cut. Read these “Rules for
Safe Operation” with care.
Follow the instructions in your operator’s manual.
Read the operator’s manual carefully. Be thoroughly familiar with the
controls and proper use of the unit. Know how to stop the unit and shut
off the engine. Know how to unhook a harnessed unit quickly.
Never allow anyone use unit without proper instruction. Be sure the
operator wears the foot, leg, eye, face and hearing or thrown objects.
Keep the area clear of bystanders, children and pets. Never allow
children to operate or play with the unit.
Do not allow anyone to enter the operating DANGER ZONE with you.
The danger zone is an area 15 meters in radius (about 16 paces) or 50
feet.
Insist that persons in the RISK ZONE beyond the danger zone wear eye
protection from thrown objects. If the unit must be used where there are
unprotected people, operate at a low throttle speed to reduce the risk of
thrown objects.
Move the stop switch to “O” position when the engine idles, insure it
reliable before cutting. Only may continue to operate the unit when stop
switch is in good condition.
Routines for checking that the cutting attachment stops turning when
the engine idles.
WARNING!
In addition to head, eye, face and ear protector shoes to protect your
feet improve your footing on slippery surfaces. Do not wear ties, jewelry,
or loose, dangling clothing which could be caught in the unit.
Do not wear open-toed footwear, or go bare-foot or bare legged. In
certain situations you must wear total face and head protection.
USER MANUAL
11
DANGER ZONE:
NO PERSON EXCEPT OPERATOR ALLOWED 15 METERS
RADIUS DANGER ZONE. EYE, EAR, FACE, FOOT, LEG AND BODY
PROTECTION MUST BE WORN BY OPERATOR. PERSONS IN
ZONE OR RISK BEYOND DANGER ZONE SHOULD WEAR EYE
PROTECTION AGAINST THROWN OBJECTS. RISK DIMINISHES
WITH DISTANCE FROM DANGER ZONE.
15 Meters
50 Feet
Danger Zone
CUTTING WITH A NYLON HEAD
WARNING!
Tilting the head to the wrong side will shoot the debris TOWARDS you.
If the line head is held flat to the ground so that cutting occurs on the
whole line circle, debris will be THROWN at you, drag will slow the
engine down, and you will use up a lot of line.
WARNING!
The proper debris shield must be in place on the unit when nylon cutting
line is used, the cutting line can flap around if too much line is exposed.
Always use the plastic debris shield with cut-off knife when using nylon
cutting heads.
WARNING!
Use only quality nylon monofilament line of the diameter 2.5mm. Never
use wire or wire-reinforced line in place of nylon trimmer line. Load
12
GASOLINE BRUSH CUTTER
your nylon line cutting head only with nylon trimmer line of the proper
diameter.
WARNING!
Use extreme caution when operating over bare spots and gravel,
because the line can throw small rock particles at high speeds. Debris
shields on the unit cannot stop objects which bounce or ricochet off hard
surfaces.
For nearly all cutting, it is good to tilt the line head so that contact is
made on the part of the line circle where the line is moving AWAY from
you and the debris shield. (See appropriate) This results in the debris
being thrown AWAY from you.
TRIMMING
Tilt the head slowly to direct debris away from you. If cutting up to a
barrier such as fence, wall or tree, Approach from an angle where any
debris ricocheting off the barrier will fly away from you, Move the line
head slowly until the grass is cut right up the barrier, but do not jam
(overfeed) the line into the barrier.
If trimming up to a wire mesh or chain linked fence be careful to feed
only up to wire. If you go too far the line will snap off around the wire.
Trimming can be done to cut through weed stems one at a time. Place
the trimmer line head near the bottom of the weed-never high up which
could cause the weed to chatter and catch the line. Rather than cut the
weed right through, just use the very end of the line to wear through the
stem slowly.
Debris
Cut ON This Side
USER MANUAL
13
SCALPING AND EDGING
Both of these are done with the line head tilted at a steep. Edging is
trimming the grass back where it has spread over a sidewalk or drive
way. During both edging and scalping, hold the unit a steep angle and in
a position where the debris, and any dislodging dirt and stones, will not
come back towards you even if it ricochets off the hard surface. Every
operator must find for himself the angles which suits his body size and
cutting situation.
CUT OFF KNIFE
CUTTING WITH A BLADE
.SCYTHING WEEDS
This is cutting by swinging the blade in a level arc. It can quickly clear
areas of field grass and weeds. Scything should not be used to cut large,
tough weeds or woody growths.
NOTE
Do not use a brush blade to cut trees which exceed a diameter of 1/2 to
3/4 inches.
Scything can be done in both directions, or just in one way which results
in the debris being thrown away from you.
That is using the side of the blade that it is rotating away from you. Tilt
down the blade slightly on this same side. You will be hit by some debris
14
GASOLINE BRUSH CUTTER
if you scythe in both directions.
Cut only with the side of the blade that the debris is moving away from
you.
If kickback occurs, the blade may be dull, the material so thick and hard
that you should use other tool instead of this machine.
Do not force the blade to cut. Do not change the angle of cut after into
the wood. Avoid using any pressure or leverage which could cause the
blade to bind or crack.
FUEL & OIL MIXTURE
CAUTION
-Never fill the fuel tank to the very top.
-Never add fuel to the tank in a closed non-ventilated area.
-Do not add fuel to this unit close to an open fire or sparks.
-Be sure to wipe off spilled fuel before attempting to start engine.
-Do not attempt to refuel a hot engine.
Fuel used for this model is a mixture of unleaded gasoline and approved
engine lubricant. When mixing gasoline with two-cycle engine oil, use
only gasoline which contains NO ETHANOL or METHANOL(Types of
Alcohol) Use Branded 89 octane or higher.
Unleaded gasoline known to be of good quality. This will help to avoid
possible damage to engine fuel lines and other engine parts.
NOTE
MIXTURE RATIO IS 40:1
GASOLINE-40PART OIL-1 PART
Fuel mixture at the rate other than 40:1 may cause damage to the
engine, Ensure mixture ratio is correct.
.FUEL
The engine uses two-stroke fuel, a mixture of gasoline and 2-stroke
lubricant 40:1
USER MANUAL
15
IMPORTANT
Two-stroke fuel may separate. Shake fuel container thoroughly before each use.
Stored fuel ages. Do not mix more fuel than you expect to use within a month.
.GASOLINE
Use branded 89 octane or higher unleaded gasoline known to be of
good quality.
.STORING FUEL
Store fuel only in a clean, safe, approved container. Check and follow
local ordinances. on type and location of storage container.
.FUEL AND OIL MIXTURE
Inspect fuel tank making sure that it is clean and fill with fresh fuel. Use
a mixture of 40:1
PREPARING FOR OPERATIONS
DO NOT MIX GASOLINE AND OIL DIRECTLY IN THE ENGINE FUEL
TANK.
IMPORTANT
-Failure to follow proper fuel mix instructions may cause damage to the
engine.
1. When preparing fuel mixture, mix only the amount needed for the
job you are to do. Do not use fuel that has been stored longer than one
months. Fuel mixture stored longer than this will cause hard starting and
poor performance. If fuel mix has been stored longer than this time. It
should be removed and filled with fresh mixture.
WARNING
2. Never fill the fuel tank to the very top.
3. Never add fuel to the tank in a closed non-ventilated area.
16
GASOLINE BRUSH CUTTER
4. Do not add fuel to this unit close to an open fire or sparks.
5. Be sure to wipe off spilled fuel before attempting to start engine
6. Do not attempt to refuel a hot engine
.CHECK POINTS BEFORE OPERATION
1. Check for loose bolts. Nuts and fittings.
2. Check the air cleaner for dirt. Clean the air filter of all dirt. Etc. before
operation.
3. Check to be sure that protector is securely in place.
4. Check to be sure that is not leak.
5. Check to be sure the blade is not running in idling speed.
WARNING
The engine exhaust from this product contains chemicals known to
cause cancer, birth defects, or other reproductive harm.
OPERATIONS
.ENGINE STARTING AND STOPPING PROCEDURES
.STARTING COLD ENGINE
Move the stop switch to “I” position.
Give a gentle push on the primer pump repeatedly (7-10times)
1.
USER MANUAL
17
until fuel comes into the primer pump. 10X
2. Pull choke lever up to close choke.
3. Pull starter handle until engine flash fires.
Push choke lever down to open choke (excessive cranking with
4.
choke lever will cause flooding engine making it difficult to start). Pull
starter handle until engine starts.
5. Allow engine to warm up for a few minutes before using.
6. Allow engine to warm up for a few minutes before using.
.STARTING WARM ENGINE
If fuel tank was not run dry, pull starter. One to three times and should
start.
.DO NOT USE CHOKE
If fuel tank was run dry, after refilling repeat steps 3 thru 6 in. STARTING
COLD ENGINE. STOPPING THE ENGINE
- Move switch to “O” position
MAINTENANCE & CARE
.AIR FILTER
- Accumulated dust in the air filter will reduce engine efficiency. Increase
fuel consumption and allow abrasive particles to pass into the engine.
Remove the air filter as often as necessary to maintain in a clean
condition.
- Light surface dust can readily be removed by tapping the filter. Heavy
deposits should be washed out in suitable solvent.
- Remove filter cover by loosening air filter cover knob.
.ADJUSTING CARBURETOR NOTE
Do not adjust carburetor unless necessary. If you have trouble with the
Carburetor, see your dealer. Improper adjustment may cause engine
damage.
18
GASOLINE BRUSH CUTTER
.FUEL FILTER
- Fuel tank is fitted with a filter. Filter is situated at the free end of fuel
pipe and can be picked out through fuel port with a piece of hooked wire
or the like.
- Check the fuel filter periodically. Do not allow dust to enter into fuel
tank. Clogged filter will cause difficulty in starting engine or abnormalities
in engine performance.
- When filter is dirty, replace the filter.
- When the inside of the fuel tank is dirty, it can be cleaned by rinsing the
tank out with gasoline.
.CHECK SPARK PLUG
Do not attempt to remove the plug from a hot engine in order to avoid
possible damage to the threads.
TROUBLE SHOOTING
- Clean or replace the plug if fouled with heavy oily deposits.
- Replace the plug if the center electrode is worn rounded at the end.
- Spark gap 0.6-0.7mm (.023“.028“)
- Fastening torque = 145-155kg.cm (125-135in.lb)
.TRANSPORT
- The engine should be turned off when the unit is moved between work
areas.
- After the engine has stopped, the muffler is still hot. Never touch hot
parts such as the muffler.
- Confirm that the fuel is not leaked from tank.
WARNING
Always cover the metal blade with the transportation guard while
transportation and storage.
USER MANUAL
19
.EXTENDED STORAGE
- Inspect, clean and repair unit if necessary.
- Remove all fuel from tank.
- Start engine-This will consume all fuel in fuel line and carburetor.
- Remove spark plug and pour one tea spoon of clean motor oil into
spark plug hole of cylinder-replace spark plug.
- Store in clean, dry, dust free area.
FAILURES such as difficulty in starting engine, irregularity in functions
and abnormality in performance can normally be prevented if careful
attention is paid to all operating instructions and maintenance procedures.
NOTE
Should the engine not function properly, check the following:
- That the fuel system is in good condition and fuel is flowing to the
engine.
- The ignition system is in good condition and the spark plug, sparks
correctly;
- Compression of the engine is adequate.
.FAILURE TO START
- Dispose of fuel in tank.
- Insure that fuel is fresh and clean.
- Check fuel filter to make sure it is clean. (Replace filter if necessary).
- Make sure air filter elements are clean.
- Install new, properly gapped spark plug.
- When there is serious trouble with the unit, do not try to repair it yourself
but have your distributor or dealer do it for you.
20
GASOLINE BRUSH CUTTER
TROUBLESHOOTING GUIDE
.FAILURE TO START
Symptom
cylinder
Probable Cause
spark
plug
spark
normal
fuel system
abnormality
these is no fuel in
Add fuel in tank
tank fuel filter obstruct Clean fuel filter
fuel
system
normal
fuel
fuel is too dirty there
is water in fuel there
is too much mixture
ratio is improper
high
voltage
wire
spark
normal
spark plug fouled
with oily deposits
spark
Spark plug insulation
plug
damage Spark gap is
too large or small
compress
pressure
normal
fuel
system
normal
fuel
Ignition
system
System
normal
normal
Remedy
instead fuel
tear down spark
plug and dry it
mixture
peroration
- clean the oil
deposits
- replace spark
plug
- adjust spark
gap 0.6-0.7mm
high voltage spark
abnormality
- high voltage wire
breach or break off
- coil looseness
- replace or
tighten
- tighten
compress
press
is
shortage
piston ring attrite
piston ring is broken
piston ring
cementation
spark plug looseness
conjoint surface of the
cylinder and crank
cast leak
replace a new
replace
eliminate
tighten
eliminate
Compress
normal
High voltage wire and
spark
Plug contact badness
Stop switch failure or
short
circuit
tighten the spark
plug cap
repair or replace
USER MANUAL
21
.LOW OUTPUT
symptom
probable cause
remedy
fuel filter obstruct,
flameout when speedup
fall short of fuel
the smoke is thin,
muffler fouled with oily
carburetor spout backward
deposits
clean fuel filter、clean fuel
road、
adjust carburetor
clean the oily deposits
compress press is shortage
piston、piston ring、
cylinder attrite、
replace piston、piston ring
engine leak
Conjoint surface of the
Cylinder and crank cast
leak
repair
the end of two crank shaft
leak
the seal is bad
replace seal
engine overheats
avoid use it for long time、
high speed and heavy
load
clean the oily deposits
burning room fouled with
oily deposits
.ENGINE RUNNING UNSTABLE
symptom
there are metal knock
sound
22
probable cause
piston、piston ring、
cylinder attrite、
piston pin、piston attrite
bearing of crank shaft
attrite
remedy
replace piston、piston ring
replace piston pin、piston
replace bearing
there are metal knock
sound
engine overheat
burning room fouled with
oily deposits
gasoline branded is unfit
avoid use it for long time、
high speed and heavy load
clean the oily deposits
replace require branded
octane
engine ignition break off
there is water in fuel
spark gap is wrong
coil gap is wrong
instead fuel
adjust spark gap 0.60.7mm
adjust coil gap 0.3-0.4mm
GASOLINE BRUSH CUTTER
.THE ENGINE SUDDENLY STOPPED
probable cause
remedy
add fuel
fuel is used up
spark plug fouled with oily deposits and short clean the oily deposits
connect
circuit
high voltage wire fall off
USER MANUAL
23
">