Siemens SIMATIC IPC IPC647D Industrial PC Operating Instructions
Below you will find brief information for Industrial PC SIMATIC IPC IPC647D. The SIMATIC IPC647D is a 19-inch rack-mountable industrial PC with a wide range of features including high performance, rugged design, and a variety of interfaces for connection to other devices. It is ideal for use in industrial automation and control applications.
Advertisement
Advertisement
SIMATIC IPC647D
SIMATIC
Industrial PC
SIMATIC IPC647D
Operating Instructions
01/2015
A5E32996306-AB
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger.
DANGER indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION indicates that minor personal injury can result if proper precautions are not taken.
NOTICE indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E32996306-AB
Ⓟ 02/2015 Subject to change
Copyright © Siemens AG 2015.
All rights reserved
Preface
These operating instructions contain all the information you need for commissioning and operation of the SIMATIC IPC647D .
It is intended both for programming and testing personnel who commission the device and connect it with other units (automation systems, programming devices), as well as for service and maintenance personnel who install add-ons or carry out fault/error analyses.
Basic knowledge required
A solid background in personal computers and Microsoft operating systems is required to understand this manual. General knowledge in the field automation control engineering is recommended.
Validity of the Operating Instructions
These operating instructions are valid for all supplied versions of the SIMATIC IPC647D.
Scope of this documentation
The documentation for the SIMATIC IPC647D includes:
● Product Information "Important notes on your device"
● Quick Install Guide SIMATIC IPC647D
● SIMATIC IPC647D operating instructions in English and German
The documentation is part of the "Documentation and Drivers" DVD supplied with the product.
Refer to the corresponding user documentation for information and instructions on using software.
Conventions
The terms "PC" or "device" are sometimes used in place of the product name
SIMATIC IPC647D in these operating instructions.
History
Currently released versions of these operating instructions:
Version
01/2014
01/2015
Comments
First edition
Second edition, amendments: Windows Server 2012 R2, devices with RAID hardware
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
3
Preface
4
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Table of contents
1
2
3
4
1.1
1.1.1
1.1.2
1.1.3
1.2
1.2.1
1.2.2
1.2.3
1.3
2.1
2.2
3.1
3.1.1
3.1.2
3.1.3
3.2
3.2.1
3.3
3.3.1
3.3.2
3.3.3
3.3.4
3.3.4.1
3.3.4.2
3.3.4.3
3.3.5
3.3.6
3.3.6.1
3.3.6.2
3.3.7
4.1
4.2
4.3
4.4
4.4.1
4.4.2
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
5
6
Table of contents
5
6
7
4.4.3
4.4.4
4.4.5
4.4.5.1
4.4.5.2
4.4.5.3
4.5
4.6
5.1
5.1.1
5.1.2
5.1.3
5.1.4
5.1.5
5.1.6
5.2
5.3
6.1
6.2
6.3
6.4
6.5
6.5.1
6.5.2
6.5.3
6.5.4
6.5.4.1
6.5.4.2
6.5.4.3
6.6
6.6.1
6.6.2
6.6.3
6.6.4
6.6.5
6.6.6
6.6.7
6.6.8
6.6.8.1
6.6.8.2
7.1
7.2
7.2.1
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Table of contents
8
7.6
7.6.1
7.6.2
7.6.3
7.6.4
7.6.5
7.6.6
7.6.7
7.6.8
7.6.9
7.6.10
7.5
7.5.1
7.5.2
7.5.3
7.5.4
7.5.5
7.5.6
7.5.7
7.5.8
7.5.9
7.5.10
7.2.2
7.3
7.3.1
7.3.2
7.3.3
7.3.4
7.3.5
7.3.6
7.4
7.4.1
Special feature: Replacing hard disk in the RAID system when switched off ...................... 100
Setting up the language selection using the Multilanguage User Interface (MUI) ............... 128
8.1
8.2
8.2.1
8.3
8.3.1
8.3.2
8.3.3
8.4
8.4.1
8.4.2
8.4.3
8.4.4
8.4.5
8.5
8.5.1
8.5.1.1
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
7
8
Table of contents
A
B
8.7
8.7.1
8.7.2
8.7.3
8.7.4
8.7.5
8.7.6
8.7.7
8.6
8.6.1
8.6.2
8.6.3
8.6.4
8.6.5
8.6.6
8.6.7
8.6.7.1
8.6.7.2
8.8
8.5.1.2
8.5.1.3
8.5.1.4
8.5.1.5
8.5.2
8.5.2.1
8.5.2.2
8.5.3
8.5.3.1
8.5.3.2
8.5.4
8.5.4.1
8.5.4.2
8.5.5
8.5.5.1
8.5.5.2
8.5.5.3
Assignment of expansion interface to the software in the TIA Portal (CP assignment) ...... 208
A.1
A.2
A.3
A.4
A.5
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Overview
1.1
1
Product description
The SIMATIC IPC647D is an industrial PC in 19" rack format design. The SIMATIC IPC647D has the following characteristic features:
● High-performance industrial functionality
● Highly compact
● Extremely rugged
● Extensive product continuity
The SIMATIC IPC offers system integrators, cabinet designers, system engineers and machine designers a 19" rack PC platform for high-performance applications and IT applications on the control and cell level for:
● Process and visualization applications
● Industrial image processing
● Quality assurance and monitoring tasks
● Measurement, control and rule-based tasks
● Data acquisition and management
The SIMATIC IPC has CE certification for use in the industrial sector as well as in residential and commercial areas and small businesses. In addition to the industrial applications, therefore, it can also be used in building automation or in public facilities.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
9
Overview
1.1 Product description
1.1.1 Highlights
Highly compact
● Compact housing design (2 HU)
● Flexibility for space-saving cabinet installation
High degree of industrial capability
● High operational vibration and shock resistance
● Wide operational temperature range
● High service friendliness
● Dust protection
● Distinct diagnostic features
Ideal for industrial applications
● Integrated PROFIBUS DP / MPI interface (optional, compatible with CP5622)
● PROFINET interface CP 1616 onboard (optional)
● PCI, PCIe I/O, PEG slots
PEG graphics and onboard graphics can be used simultaneously
● High flexibility and expansibility of components
High investment protection
● High continuity of the components/design
● Guaranteed spare parts availability for at least 5 years
● Simple integration in PC-based automation
High system availability
● SIMATIC IPC DiagMonitor – PC diagnostics and message software via OPC/SNMP/LAN
● SIMATIC PC/PG Image Creator – data imaging software
● Optional ECC memory module
● Redundant power supply with status message
● RAID configurations: RAID controller onboard or powerful hardware RAID controllers
(PCIe x8) with Zero-Maintenance Cache Protection module
● RAID1 – redundant data storage on two hard drives, also "hot swap" in connection with removable drive bays
(hot-spare equipment is supported)
10
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
1.1.2
Overview
1.1 Product description
Function
● Integral, configurable monitoring functions:
– Program execution (watchdog)
– Internal housing temperature
– Fan speed
● Enhanced diagnostic/messaging via Ethernet, E-mail, SMS, and for direct input in
SIMATIC software via OPC (optional using SIMATIC IPC DiagMonitor):
– Operating hours counter
– Hard disk status
– System status (heartbeat)
– Automatic logging of all messages to a log file
– Option of remote monitoring of networked SIMATIC IPCs
● RAID1 (mirroring): For automatic data mirroring on two hard disks. Configurations with hot-spare drive available for order.
● Hardware RAID
– Auto-Rebuild for change of hard disk
– "Zero-Maintenance Cache Protection" protects the data in the hardware RAID controller cache in the event of a power failure
– Reduced load on the main processor during the rebuild
– Fast 1 TByte SAS hard disks for maximum speed when reading and writing data
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
11
Overview
1.1 Product description
1.1.3 Features
General features
Design
•
19” rack, 2 HU
• Rugged panel-mount housing, all metal
•
Prepared for mounting telescopic rails
• Can be mounted horizontally
•
Lockable front cover as access protection
Enclosure
•
Dust protection by means of overpressure ventilation using bearing seated front fan through filter
•
Enclosure cover fastened with a single screw
•
Front fan can be exchanged without tools
•
Card retainer for reliable operation of PC modules under vibration and shock conditions
Drive bays
•
2 × removable drive bays, slimline or
• 2 × 3.5" drive in vibration-damped drive cage and
•
1 × slimline DVD format
Max. 4 slots
1
, equipment PCI/PCIe, depending on configuration Slots for expansion cards (long)
Graphics
•
CRT (via DVI-I VGA adapter): Up to 2560x1600 at 120 Hz / 32-bit color depth
• LCD via DVI-D: Up to 2048 x 1152 at 60 Hz, 32-bit color depth
•
LCD via DisplayPort: Up to 4096 x 1152 at 24 Hz, 32-bit color depth
Interfaces
PROFIBUS/MPI 12 Mbps (isolated potential, compatible to CP -5622), optional
PROFINET
Ethernet
10/100 Mbps (CP 1616 onboard), three RJ45; optional
2 x 10/100/1000 Mbps (two RJ45)
Wake on LAN, Remote Boot and teaming are supported
USB
Serial
Parallel
Monitor
2 x front panel, 4 x rear panel, 1 x internal; (high current)
COM1 (V.24), COM2 (V.24) optional, through slot plate adapter
LPT optional, through slot plate adapter
•
1 x DVI-I (for DVI-D or VGA using cable adapter)
• 2 × DisplayPort
•
2 × DVI-D/VGA with Dual Head graphics card (optional, via cable adapter)
Keyboard
Mouse
Audio
Power supply
PS/2
PS/2
Microphone, Line out / Headset
100 VAC to 240 VAC, wide range; with short-term power failure backup in accordance with NAMUR: Max. 20 ms at 0.85 rated voltage
1
The optional hardware RAID controller occupies two slots
12
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Overview
1.1 Product description
Monitoring functions
Temperature
Fan
Watchdog
Status LEDs
• Overshoot/undershoot of permissible operating temperature
•
Messages can be evaluated by an application program.
•
Speed monitoring
•
Messages can be evaluated by an application program.
•
Monitoring of the IPC
• Monitoring time can be parameterized in software
•
Restart can be parameterized in the event of a fault
• Messages can be evaluated by an application program.
•
POWER (internal power supply unit, PC switched On)
• HDD (access to hard disk drive)
•
ETHERNET 1, ETHERNET 2 (Ethernet status, "heartbeat")
• PROFIBUS/MPI (activation display of the PROFIBUS/MPI interface), optional product feature
•
SF PROFINET (status display of the CP 1616 onboard interface), optional product feature
• WATCHDOG (Watchdog function/error display)
•
TEMP (temperature status)
• FAN (speed monitoring)
•
HDD0 Alarm, HDD1 Alarm: RAID status message in conjunction with
SIMATIC monitoring software (only with RAID option)
Basic variant
Motherboard
Bus board
Processor
RAM expansion
Motherboard without fieldbus, Intel® DH82C226 Express Chipset
PCI, PCIe x4, PCIe x16, 2 variants
• Intel® Xeon™ E3-1268L v3 2.3 (3.3) GHz, 4 cores, GT2, 8 MB SLC, HT
•
Intel® Core™ i5-4570TE 2.7 (3.3) GHz, 2 cores, GT2, 4 MB SLC, AMT
• Intel® Core™ i3-4330TE 2.4 GHz, 2 cores, GT2, 3 MB SLC, AMT
Up to 32 GB SDRAM DDR3 1600MT/s
4 DIMM base with or without ECC
1
Drives
Hard disks
Optical drive
3.5" SATA 6 Gbit/s or SAS, 500 GB / 1000 GB
Maximum 4 × 3.5" SAS hard disks in the removable drive bay
The quantity depends on the IPC type
Slimline SATA
1
Memory expansions ≥4 GB can only be used in combination with 64-bit operating systems.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
13
Overview
1.1 Product description
Optional accessories
PROFIBUS/MPI
PROFINET
Drives, RAID controller
SAS Hardware RAID controller
12 Mbps (isolated potential, compatible to CP 5622)
10/100 Mbps (CP 1616 onboard, three RJ45)
DVD burner
Hard disks 3.5" (SATA or SAS)
• PCIe x8 expansion card
The adjacent slot must remain free.
•
Intelligent PCIe x8 RAID controller type: PMC Sierra
ASR-8405 for max. 4 SAS drives
• With CPU, cache memory (thus, negligible effect on the system)
•
With battery backup for data reliability in the event of power failures
Read:
DVD ROM: Single Layer8x, Dual Layer 6x
DVD-R/+R: Single layer 8x, Dual layer 6x
DVD-RW/+RW 8x, DVD-RAM 5x
CD-ROM/CD-R Read 24x, CD-RW 24x
Write:
DVD+R 8x, DVD+RW 8x, DVD-R 8x, DVD-RW 6x
DVD+R (DL) 6x, DVD-R DL 2x
CD-R 24x, CD-RW 24x
Installation in drive cage (with vibration damping)
•
500 / 1000 GB (SATA)
• 2 × 1000 GB (SATA)
RAID1: 1000 GB (2 × 1000 GB, SATA)
Installation in the drive cage of the removable drive bay
• 500 GB (SATA)
•
1000 GB (SATA)
• 2 × 1000 GB (SATA)
•
RAID1:
Solid State Drive 2.5" (SATA)
1000 GB (2 × 1000 GB, SATA or SAS)
•
240 GB MLC, internal or in removable drive bay
Graphics cards
DVI-I to VGA adapter
Operating system
PCIe x16 graphics card, dual head (2 x VGA or 2 x DVI-D)
Used to connect a monitor with a VGA port to the PC (can be ordered by configurator).
Preinstalled and activated, included on restore DVD
•
Windows Server 2008 R2, MUI
1
, 64 bit
•
Windows Server 2012 R2, MUI
1
, 64 bit
•
Windows 7, MUI
1
, 32 bit / 64 bit
Power supplies
Redundant AC power supply Monitored AC-100/230 V power supply, 350 W
1
MUI: German, English, French, Spanish and Italian
14
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Overview
1.1 Product description
Operating system languages
The following languages for the operating system can be installed from the recovery DVD:
Language Windows Server
2008 R2
Windows Server
2012 R2 UP1
Windows 7 32/64-bit
German (Germany)
English (United States)
French (France)
Italian (Italy)
Spanish (Spain)
Japanese (Japan)
Korean (Korea)
Russian (Russia)
Chinese (PRC)
Chinese (Hong Kong S.A.R.)
Chinese (Taiwan)
X
X
X
X
-
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
X
X
X
X
X
X
Optional software
SIMATIC IPC DiagMonitor V4.4.3 or higher
SIMATIC IPC Image & Partition
Creator V3.3.3 or higher
Software for monitoring local and remote SIMATIC PCs:
• Watchdog
•
Temperature
• Fan speed
•
Hard disk monitoring (SMART, RAID status)
• Monitoring modules of the redundant power supply
•
System / Ethernet monitoring (Heartbeat)
Software tool for local data backup and setting up of the hard disks.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
15
Overview
1.2 Design of the device
1.2 Design of the device
1.2.1
Front view
Device views
①
Front panel with openings for ventilation of the device
⑧
On/off button
②
Rating plate
③
Front door
⑨
Installation option for drives
The following drives can be ordered optionally:
•
HDD or SSD in removable drive bay
④
Status displays
•
DVD burner drive, Slimline
•
HDD in vibration-damped drive cage
•
SSD in internal drive cage
⑤
Reset button
⑥
USB 2.0 port
⑦
USB 3.0 port
⑩
Lock for front door
16
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Rear view with AC power supply
Rear view with redundant power supply
Overview
1.2 Design of the device
①
AC power supply
②
Power supply
③
On/off switch
④
⑤
Expansion card slots
①
Power supply
②
Acknowledgment
③
Module 1 of the redundant power supply
④
Module 2 of the supply
⑤
On/off switch
⑥
Status LED module 1
⑦
⑧
Expansion card slots
1.2.2 Interfaces
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
17
Overview
1.2 Design of the device
Dual-head adapter
①
Connection for equipotential bonding
②
Fieldbus cover: No fieldbus, PROFIBUS or PROFINET
1
③
USB ports
Left sockets: Connection for USB 2.0 devices
Right sockets: Connection for USB 3.0 / USB 2.0 devices
USB 2.0 and USB 3.0 connections use different USB ports.
④
ETHERNET interfaces 1 and 2
LAN interfaces are numbered on the enclosure to provide unique identification. The numbering by the operating system may deviate from this.
⑤
COM interface
⑥
DisplayPort port
⑦
PS/2 interface for keyboard
⑧
PS/2 interface for mouse
1
Depending on the ordered device configuration
The adapter is necessary if you want to connect one of two monitors to the optional
Dual Head graphics card.
⑨
DVI-I port
⑩
Slot plate adapter with LPT and
⑪
Audio input for analog audio phono jack
⑫
Audio output for active speakers
⑬
Slots for expansion cards
⑭
DMS59 connector
⑮
DVI-I connector
⑯
VGA adapter
18
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
1.2.3
Front panel
Status displays
View with open front door
Overview
1.2 Design of the device
Operating display
POWER
Meaning LED Description
HDD
ETHERNET 1
ETHERNET 2 optional
1
1
SF PROFINET,
PROFIBUS/MPI
(optional)
Operating mode of the PC
OFF
YELLOW
GREEN
Access to hard disk OFF
GREEN
Status connection
ETHERNET
OFF
GREEN
PC disconnected from power supply
PC in standby
PC in operation
No access
Access of onboard SATA hard disk
•
No connection
• Connection
•
No data traffic
•
Connection
• Data traffic
Status connection S7 or PROFIBUS
Flashes
GREEN according to activity
OFF
Status
CP 1616 onboard
GREEN
OFF
•
No connection
• No data traffic
Data traffic
•
CP not available
• CP disabled
•
No error, communication established
• Charging in progress
•
CP 1616 driver not installed
• CP in NDIS mode
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
19
Overview
1.2 Design of the device
Flashes slowly
RED
•
Link status error
•
IO controller: IO device cannot be addressed
•
IO controller: Duplicate IP address
Flashes rapidly
RED
RED
Exception error: diagnostics via Web or
SNMP is no longer possible
•
Diagnostics information available
• No communication established.
WATCHDOG
TEMP
FAN
HDD0 ALARM
HDD1 ALARM
WATCHDOG status OFF
GREEN
RED
Temperature status OFF
RED
Fan status
(only with active SOM or DiagMonitor software)
HDD alarm in connection with RAID and monitoring software
OFF
RED
OFF
RED, 1 ×
RED, 2 ×
WATCHDOG not activated
WATCHDOG monitoring enabled
Monitoring time elapsed
Internal temperature OK
Internal temperature critical
Fan speed OK
Fan speed too low
RAID is OK
HDD0 or HDD1 not OK
RAID is not OK
Localization of the hard disk see Section
"Displaying a defective hard disk of a RAID system in the RAID software (Page 99)"
All displays are lit
Error in early BIOS
Post
Both flash RAID synchronization in progress
All lit CPU has not started up
Error in early POST
1
For unique labeling, the Ethernet ports are numbered on the enclosure. The numbering by the operating system may deviate from this.
20
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Ethernet interface
Overview
1.2 Design of the device
Display
Ethernet 1, 2
P1, P2, P3
1
1
PROFINET LAN X1
Meaning
Green LED
Link status display
Yellow LED
Activity status display
Green LED
Link status display of
CP-1616 channel
Yellow LED
Activity status display of
CP-1616 channel
LED
Off
Green
Orange
Off
Description
• No cable connected
•
Cable disabled
• Interface disabled, 10 MBit cable active
100 Mbit cable active
1000 Mbit cable active
• No cable connected
•
Cable disabled
• Interface disabled
Lit
• Connection
•
No activity
Goes out briefly Activity
Off
• No cable connected
•
Cable disabled
• Interface disabled
Green
Off
Active cable connected
•
No cable connected
•
Cable disabled
•
Interface disabled
Lit
• Connection
•
No activity
Goes out briefly Activity
1
For unique labeling, the LAN and PROFINET interface are numbered on the enclosure. The numbering by the operating system may deviate from this.
Drives in removable rack
①
"Power" LED; power supply available
②
"HDD" LED, access to hard disk drive
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
21
Overview
1.3 Accessories
Virtual status display
The two "virtual" CP -1616 LEDs are only visible in the SIMATIC user interface and can be read via SNMP.
PROFINET Virtual LEDs RUN CP is active
STOP
Flashes
CP is in the stop state
The states "flashes slowly" and
"flashes rapidly" do not exist.
1.3
Name
Retainer for locking the internal USB interface
Accessories
Accessories are available for your device. These are not included in the scope of delivery.
Information on available accessories is listed in the table below and on the Internet at the following addresses:
● IPC expansion components ( http://www.automation.siemens.com/mcms/pc-basedautomation/en/industrial-pc/expansion_components_accessories )
● Industry Mall ( https://mall.industry.siemens.com
)
Description
The retainer is a mechanical safety device for the internal USB interface. It optimizes the protection of an internal
USB memory stick against loads caused by vibration and shock during transportation or operation.
This increases the reliability and operational safety of the device.
IPC647D IPC847D x x
Article number and figure
6ES7648-1AA00-0XK0 x 6ES7648-1AA00-0XD0 Tower Kit
(not available in all countries)
You can use the Tower Kit to convert the device into an industrial Tower PC.
This step expands the operating range beyond the control cabinet.
Components of the Tower Kit:
• Cover
①
•
Base
②
• Accessories: Screws and rubber feet
-
22
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Overview
1.3 Accessories
Name
Tray for low-profile removable drive bay
Description
The removable drive bay makes for quick and simple replacement of a 3.5'' hard disk or 2.5" SSD without having to open the device or remove it from the control cabinet. The result is the following advantages for service and maintenance, data backup and data transfer:
•
Replacement of a failed hard disk in operation ("hot swap") in RAID configurations
•
Downloading different system states or operating systems from different hard drives during a short period of time.
•
Simplified data backup by copying, for
example, to a backup hard drive.
•
Simple transportation of backup data
•
Separate data storage and archiving possible
VGA / DVI adapter Graphics adapter cable DVI-I to VGA,
250 mm long
DP / DVI adapter Graphics adapter cable, DisplayPort to
DVI
IPC647D IPC847D x x x x x x
DP / VGA adapter Graphics adapter cable, DisplayPort to
VGA x x
Article number and figure
6ES7648-0EG01-1BA0
6ES7648-3AB00-0XA0
6ES7648-3AF00-0XA0
6ES7648-3AG00-0XA0
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
23
Overview
1.3 Accessories
24
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Safety Instructions
2
2.1 General safety instructions
Fully disconnecting the device from mains voltage
WARNING
Risk of fire and electric shock
The on/off button and on/off switch do not fully disconnect the device from the mains. If the device is switched off with the on/off switch, there remains a risk of electric shock and fire hazard, for example, if the device or connection cables are damaged or if the device is used improperly.
Always fully disconnect the device from the mains voltage as follows before performing work on the device or when the device will not be used over an extended period of time.
•
If the device was not mounted in a control cabinet: Shut down the operating system and pull the power plug on the rear of the device.
•
If the device was mounted in a control cabinet: Shut down the operating system and switch the AC circuit breaker to "Off".
•
Properly connect the device to a protective conductor.
Devices in the control cabinet
WARNING
Life-threatening voltages are present with an open control cabinet
When you open the control cabinet, some areas or components may be carrying lifethreatening voltages.
If you touch these areas or components, you may be killed by electric shock.
Switch off the power supply to the cabinet before opening it.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
25
Safety Instructions
2.1 General safety instructions
System expansions
NOTICE
Damage to the device, machine or plant due to device and system expansions
Device and system expansions may contain faults and affect the entire device, machine or plant.
Device and system expansions may violate safety rules and regulations regarding radio interference suppression. If you install or replace device or system expansions and damage your device, the warranty is voided.
Note the following:
•
Only install device or system expansions designed for this device. Contact your technical support team or the point of sale to find out which device and system expansions are suitable for installation.
• Observe the information on electromagnetic compatibility provided in the technical specifications.
CAUTION
Fire hazard due to overheating of the device
Expansion cards generate additional heat. The device can overheat or cause a fire.
•
Observe the safety and installation instructions for the expansion cards.
• If necessary, install the device in an enclosure that meets the requirements of paragraphs 4.6 and 4.7.3 of the standards EN 60950-1:2006 and
IEC/UL/EN/DIN-EN 60950-1.
26
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Battery
Safety Instructions
2.1 General safety instructions
WARNING
Risk of explosion and release of harmful substances
Improper handling of lithium batteries can result in an explosion of the batteries.
Explosion of the lithium batteries and the resulting release of harmful substances can cause severe physical injury. Damaged batteries jeopardize the function of the device.
Note the following when handling lithium batteries:
• Replace used batteries in good time; see the section "Replacing the backup battery" in the section "Device maintenance and repair".
•
Replace the lithium battery only with an identical battery or types recommended by the manufacturer (order no.: A5E00047601).
• Do not throw lithium batteries into fire, do not solder on the cell body, do not recharge, do not open, do not short-circuit, do not reverse polarity, do not heat above 100°C and protect from direct sunlight, moisture and condensation.
Strong high-frequency radiation
NOTICE
Observe immunity to RF radiation
The device has an increased immunity to RF radiation according to the specifications on electromagnetic compatibility in the technical specifications.
Radiation exposure in excees of the specified immunity limits can impair device functions, result in malfunctions and therefore injuries or damages.
Observe the information on immunity to RF radiation in the technical specifications.
ESD directive
Electrostatic sensitive devices can be labeled with an appropriate symbol.
NOTICE
Electrostatic sensitive devices (ESD)
When you touch electrostatic sensitive components, you can destroy them through voltages that are far below the human perception threshold.
If you work with components that can be destroyed by electrostatic discharge, observe the
ESD directive in the technical specifications.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
27
Safety Instructions
2.1 General safety instructions
Industrial Security
Siemens offers products and solutions with Industrial Security functions that support the safe operation of equipment, solutions, machines, devices and/or networks. They are important components in a comprehensive Industrial Security concept. As a result the products and solutions from Siemens are constantly evolving. Siemens recommends obtaining regular information regarding product updates.
For safe operation of Siemens products and solutions appropriate protective measures (e.g., cell protection concept) must be taken and each component must be integrated in a comprehensive Industrial Security concept, which corresponds with the current state of technology. The products of other manufacturers need to be taken into consideration if they are also used. You can find addition information on Industrial Security under
( http://www.siemens.com/industrialsecurity ).
Sign up for our product-specific newsletter to receive the latest information on product updates. For more information, see under ( http://www.siemens.de/automation/csi_en_WW ).
Disclaimer for third-party software updates
This product includes third-party software. Siemens AG only provides a warranty for updates/patches of the third-party software, if these have been distributed as part of a
Siemens software update service contract or officially released by Siemens AG. Otherwise, updates/patches are undertaken at your own risk. You can find more information about our
Software Update Service offer on the Internet at Software Update Service
( http://www.automation.siemens.com/mcms/automation-software/en/software-updateservice/Pages/Default.aspx
).
Notes on protecting administrator accounts
A user with administrator privileges has extensive access and manipulation options in the system.
Therefore, ensure there are adequate safeguards for protecting the administrator accounts to prevent unauthorized changes. To do this, use secure passwords and a standard user account for normal operation. Other measures, such as the use of security policies, should be applied as needed.
28
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Safety Instructions
2.2 Notes on use
Access protection
CAUTION
Protection against access by unauthorized persons
An unauthorized user can operate the device incorrectly and bypass logon by restarting the device.
Operator actions by unauthorized persons jeopardize operational reliability.
Take the following safety precautions:
• Lock the front door and the removable drive bay.
•
Do not use keyboards with an on/off button (Power button).
• If the device has a on/off button, assign the parameters of the function of the on/off button to meet your requirements under Windows. You can find the settings in the
"Power Options" menu.
Headphones
CAUTION
Impaired hearing due to excessive sound pressure
The setting of the volume and the equalizer can increase the sound pressure in the headphones. Other factors not mentioned by the manufacturer can also influence the sound pressure, for example, the operating system, equalizer software, firmware and driver.
Excessive sound pressure from headphones can result in impaired hearing or even loss of hearing.
Set the volume control and equalizer to the lowest value before you put on the headphones. Keep checking the volume control setting. Only use headphones and software approved by the manufacturer.
2.2 Notes on use
NOTICE
Possible functional restrictions in case of non-validated plant operation
The device is tested and certified on the basis of the technical standards. In rare cases, functional restrictions can occur during plant operation.
Validate the correct functioning of the plant to avoid functional restrictions.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
29
Safety Instructions
2.2 Notes on use
NOTICE
Rack-mount instructions
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack, the operating ambient temperature of the rack environment may be greater than the room ambient.
Therefore consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised.
C) Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.
D) Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.
E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained.
Particular attention should be given to supply connections other than direct connections to the branch circuit (e. g. use of power strips).
Note
Use in an industrial environment without additional protective measures
This device was designed for use in a normal industrial environment according to
IEC 60721-3-3.
Ambient and environmental conditions
WARNING
Voided approvals
If the following conditions for system installation are not observed, approvals in accordance with UL 60950-1 and EN 60950-1 are rendered void and there is a risk of overheating and personal injury.
NOTICE
Damage of device caused by ambient conditions
Ambient conditions for which the device is not suitable can cause faults or damage the device.
Note the following:
•
Operate the device only in closed rooms. Failure to comply nullifies the warranty.
•
Operate the device only in accordance with the ambient conditions.
•
Observe the permitted mounting positions of the device.
30
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Safety Instructions
2.2 Notes on use
When you plan your project, you should make allowances for:
● Climatic and mechanical environmental conditions defined in the "General technical data" chapter of the operating instructions.
● This device was designed for use in a normal industrial environment. SIMATIC Rack PCs may not be operated in severe environments which are subject to caustic vapors or gases without taking additional protective measures (such as the provision of clean air.)
● Avoid extreme ambient conditions as far as possible, for example, heat.
● Do not expose the device to direct sunlight or other powerful light sources.
● Install the device in such a way that it poses no danger, for example, by falling over.
● The device conforms to protection class IP41 at the front panel. Ensure that the installation opening for the device is splash-proof in areas which may be subject to splash water.
● Always maintain a minimum clearance of 50 mm to the area of the ventilation slots in order to ensure adequate ventilation of the PC.
● Do not cover the ventilation slots of the enclosure. There must be distance of at least 5 cm at the back of the device, depending on wiring.
● The device meets requirements for fire protection housings to EN 60950-1 and can be installed without additional fire protection enclosure.
● The connected or built-in peripherals should not introduce a counter emf in excess of
0.5 V into the device.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
31
Safety Instructions
2.2 Notes on use
32
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Installing and connecting the device
3
3.1 Preparing for installation
3.1.1
Procedure
Checking the delivery package
1. When accepting a delivery, please check the packaging for visible transport damage.
2. If any transport damage is present at the time of delivery, lodge a complaint at the shipping company in charge. Have the shipper confirm the transport damage immediately.
3. Unpack the device at its installation location.
4. Keep the original packaging in case you have to transport the unit again.
Note
Damage to the device during transport and storage
If a device is transported or stored without packaging, shocks, vibrations, pressure and moisture may impact the unprotected unit. Damaged packaging indicates that ambient conditions have already had a massive impact on the device and it may be damaged.
This may cause the device, machine or plant to malfunction.
• Keep the original packaging.
•
Pack the device in the original packaging for transportation and storage.
5. Check the contents of the packaging and any accessories you may have ordered for completeness and damage.
6. Please inform the delivery service immediately if the package contents are incomplete or damaged or do not correspond with your order. Fax the enclosed form "SIMATIC IPC/PG
Quality Control Report".
WARNING
Electric shock and fire hazard due to damaged device
A damaged device can be under hazardous voltage and trigger a fire in the machine or plant. A damaged device has unpredictable properties and states.
Death or serious injury could occur.
Make sure that the damaged device is not inadvertently installed and put into operation.
Label the damaged device and keep it locked away. Send off the device for immediate repair.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
33
Installing and connecting the device
3.1 Preparing for installation
NOTICE
Damage from condensation
If the device is subjected to low temperatures or extreme fluctuations in temperature during transportation, as is the case in cold weather, for example, moisture can build up on or inside the device (condensation).
Moisture causes a short circuit in electrical circuits and damages the device.
In order to prevent damage to the device, proceed as follows:
•
Store the device in a dry place.
•
Bring the device to room temperature before starting it up.
•
Do not expose the device to direct heat radiation from a heating device.
•
If condensation develops, wait approximately 12 hours or until the device is completely dry before switching it on.
7. Please keep the enclosed documentation in a safe place. It belongs to the device. You need the documentation when you commission the device for the first time.
8. Write down the identification data of the device.
3.1.2 Identification data of the device
The device can be clearly identified with the help of this identification data in case of repairs or theft.
Noting down the device identification data
Enter the following data in the table below:
Serial number
Order no.
Microsoft Windows Product Key
Ethernet 1 address
Ethernet 2 address
CP 1616 onboard layer 2
S VP ...
6AG4112-2 ...
34
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Installing and connecting the device
3.1 Preparing for installation
The data can be found as follows:
● Serial number: The serial number (S VP) is located on the rating plate either on the rear panel of the device or on the inside of the front door.
● Order number of the device
● Device Ethernet address: The Ethernet address is printed on the device and is stored in the BIOS Setup, "Advanced" menu, submenu "Peripheral Configuration".
● Microsoft Windows "Product Key" on the "Certificate of Authenticity" (COA). The COA label is attached to the inside of the front door.
You may need the Product Key in case you reinstall the operating system.
Information on the device equipment is available on the inside of the front door.
3.1.3 Permitted mounting positions
Optional installation locations
The device can be mounted horizontally in control desks, switchboards and 19" rack systems, and possibly vertically which is not permitted in all countries.
NOTICE
Operation in closed rooms
The device is approved for operation in closed rooms only. Pay attention to the ambient and environmental conditions.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
35
Installing and connecting the device
3.2 Mounting the device
3.2 Mounting the device
3.2.1 Installation guidelines
WARNING
Danger, high voltage
A high voltage may be present in the switchgear cabinet and could cause a dangerous electric shock.
It may result in death or serious physical injury.
Isolate the power supply to the switchgear cabinet before opening it. Ensure that the power to the switchgear cabinet cannot be turned on accidentally.
NOTICE
Fire hazard
If you install the device in an unapproved mounting position or if you do not observe the ambient conditions, the device can overheat. UL approval and conformity with the lowvoltage directive (EN 60950-1:2006 and DIN EN 60950-1:2006-11) become void.
Overheating can cause a fire. Proper functioning of the device is no longer guaranteed.
Before you install the device, note the following general installation information.
Note
The device fulfills the requirements for a fire protection housing according to EN 60950-1.
Therefore, it can be installed without additional fire protection.
● Install the device only in one of the described permitted mounting positions.
● Provide adequate volume in the switchgear cabinet for air circulation and heat transport.
● Do not cover the ventilation slots of the device. There must be distance of at least 5 cm at the back of the device, depending on wiring.
● Ensure that the maximum air intake temperature directly in front of the air intake opening does not exceed the permitted temperature according to the technical specifications of the device. The maximum air intake temperature must be accounted for especially when sizing closed switchgear cabinets.
● Install the device in such a way that it does not pose a danger, for example, by falling over.
Note
For more details, consult the "Technical Data" in the "Ambient conditions" chapter.
36
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Installing and connecting the device
3.2 Mounting the device
Mounting methods
You can mount the device as follows:
● Mounting with cabinet brackets
● Mounting on device bases
● Mounting on telescopic rails
When telescopic rails are used for mounting, the device can be withdrawn fully from the cabinet or rack. You will find detailed information about the telescopic rails in sections
CAUTION
Risk of physical injury
The device is too heavy to be mounted exclusively with the 19 inch brackets of the front panel. The device may fall down, injure people and get damaged.
Secure the device using additional measures. The mounting screws of the telescopic rails may not protrude more than 5 mm into the device.
Position of the mounting holes for angle brackets or telescopic rails
The following figure highlights the mounting holes for the angle brackets and for the telescopic rails.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
37
38
Installing and connecting the device
3.3 Connecting the device
3.3
3.3.1
Connecting the device
Connection information
WARNING
Risk of fire and electric shock
The on/off button and on/off switch do not fully disconnect the device from the mains. If the device is switched off with the on/off switch, there remains a risk of electric shock and fire hazard, for example, if the device or connection cables are damaged or if the device is used improperly.
Always fully disconnect the device from the mains voltage as follows before performing work on the device or when the device will not be used over an extended period of time.
•
If the device was not mounted in a control cabinet: Shut down the operating system and pull the power plug on the rear of the device.
•
If the device was mounted in a control cabinet: Shut down the operating system and switch the AC circuit breaker to "Off".
•
Properly connect the device to a protective conductor.
WARNING
Risk of lightning strikes
A lightning flash may enter the mains cables and data transmission cables and jump to a person.
Death, serious injury and burns can be caused by lightning.
Take the following precautions:
• Pull out the power plug in good time when a thunderstorm is approaching.
•
Do not touch mains cables and data transmission cables during a thunderstorm.
•
Keep sufficient distance from electric cables, distributors, systems, etc.
Note
Make sure that the shockproof power outlet of the building installation is freely accessible and as close as possible to the device, especially when the power plug is secured with a locking power plug latch.
WARNING
Operation only in TN networks
The device is designed for use on a grounded power supply grid (TN networks per
VDE 0100 Part 100 or IEC 60364-1). Operation with non-grounded or impedance-grounded networks (IT networks) is not permitted.
Rated voltage
The permitted nominal voltage of the device must conform with local mains voltage.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
I/O devices
3.3.2
Installing and connecting the device
3.3 Connecting the device
NOTICE
Fault caused by I/O devices
The connection of I/O devices can cause faults in the device. The result may be personal injury and damage to the machine or plant. Note the following:
•
Connect only I/O devices which are approved for industrial applications in accordance with EN 61000-6-2/IEC 61000-6-2.
•
Non-hot-plug capable I/O devices may only be connected when the power supply to the device is switched off.
Damage through regenerative feedback
Regenerative feedback of voltage to ground by a connected or installed component can damage the device.
Connected or built-in I/Os, for example, a USB drive, are not permitted to supply any voltage to the device. Regenerative feedback is generally not permitted.
Connection of equipotential bonding
A low-resistance ground connection ensures that interference signals generated by external power supply cables, signal cables or cables to the I/O modules are safely discharged to ground.
The equipotential bonding connection of the device is located on the side of the device and is identified by the following symbol:
Requirement
● TORX T20 screwdriver
● An equipotential bonding cable with a minimum cross-section of 2.5 mm
2
Procedure
1. Connecting the equipotential bonding connection
①
of the device with the equipotential bonding cable. Ensure that the equipotential bonding cable has a large-area contact with the housing.
2. Connect the equipotential bonding cable with the central grounding point of the cabinet in which the device is installed. Ensure that the equipotential bonding cable has a large-area contact with the central grounding point.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
39
Installing and connecting the device
3.3 Connecting the device
3.3.3 Connecting peripheral equipment
Note
Observe suitability for industrial applications
Only connect I/O devices that are suitable for industrial applications in accordance with
EN IEC 61000-6-2.
Note
I/O devices capable of hot-plugging (USB)
Hot-plug I/O devices (USB) may be connected while the PC is in operation.
NOTICE
Non-hot-plug I/O devices
I/O devices that do not support hot-plugging may not be connected until the device is powered off. Strictly adhere to the specifications in the I/O manuals.
Note
Wait at least ten seconds before you reinsert USB devices.
Note that the EMC immunity of standard USB devices is designed only for office environments. These USB devices are appropriate for handling commissioning and service tasks. Only industrial grade USB devices are permitted for use in industrial environments.
The USB devices are developed and marketed by the respective supplier. The respective product supplier provides support for the USB devices. The manufacturer's terms of liability shall apply.
Note
A monitor should be connected and switched on before device booting to ensure it is correctly detected and run by the BIOS and the operating system. The screen may otherwise remain dark.
Note
The connected or built-in I/Os should not introduce a counter emf into the device.
A counter e.m.f. greater than 0.5 V to ground on the + 3.3 V DC / + 5 V DC / + 12 V DC due to a connected or integrated component can prevent normal operation or even destroy the computer.
When measuring the counter emf, remember the following:
•
The computer in question must be turned off and the power supply connector must be plugged in.
•
During the measurement, all cables from the plant to the computer should be connected.
•
All other components in the plant must be active.
40
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Installing and connecting the device
3.3 Connecting the device
3.3.4 Connecting the power supply
3.3.4.1 Information about the power supply
Note
Note the following points:
•
The wide-range power supplies are designed for 100 to 240 VAC power supply systems.
The setting of the voltage range takes place automatically.
• The power supply contains a power factor correction circuit to conform with the EMC directive.
•
Uninterruptible AC power systems must supply a sinusoidal output voltage in the normal and buffered mode when used with SIMATIC PCs with a PFC circuit.
UPS characteristics are described and classified in the standards EN 50091-3 and IEC
62040-3. Devices with sinusoidal output voltage in the normal and buffered mode are identified with the classification "VFI-SS-...." or "VI-SS-....".
Localized information
230 V supply voltage outside of the USA and Canada
This device is equipped with a safety-tested power cord which may only be connected to a grounded shockproof power outlet. If you choose not to use this cable, you must use a flexible cable of the following type: Cable cross-section at least 0.82 mm
2
and 15 A / 250 V ground contact connector. The cable set must be compliant with the safety regulations of the country where the device is to be installed and carry the identification labels required by law.
Operation in the USA and Canada
For the United States and Canada, a CSA or UL-listed power cord must be used. The connector must be compliant with NEMA 5-15.
120 V voltage
Use a flexible power cord which is approved to UL and CSA with the following features: SJT model with three leads, min. 18 AWG conductor cross-section, max. 4.5 m in length and parallel ground contact connector 15 A, min. 125 V.
240 V voltage
Use a flexible power cord which is approved to UL and CSA with the following features: SJT model with three conductors, min. 18 AWG conductor cross-section, max. length 4.5 m, and tandem grounded connector 15 A, min. 250 V.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
41
Installing and connecting the device
3.3 Connecting the device
3.3.4.2
Requirement
Connecting an AC power supply
● 1 power cable
● 1 power plug latch from the accessory kit
● 1 T10 screwdriver
Procedure
Mounting
1. Set the on/off switch
①
to position '0'.
This prevents an automatic starting of the device when plugging in the power cable.
2. Remove the screws
③
.
3. Plug the power cable plug outlet.
②
into the power
4. Plug the power cable plug into the power outlet.
5. Slide the power plug latch
④
over the plug.
6. Secure the power plugs, if necessary, to prevent the power cables from becoming loose accidentally: Secure the power plug latch with the screw
③
.
7. Set the on/off switch
①
to position 'I'.
The yellow power LED on the front panel of the device lights up.
Removal
For installation, follow the steps for removal in reverse order.
WARNING
Risk of fire
If the power plug is secured with a clamp, the power outlet must be freely accessible to allow the device to be easily removed from the mains.
42
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Installing and connecting the device
3.3 Connecting the device
3.3.4.3
Requirement
Connecting a redundant power supply
● 2 power cables
● 2 power plug latches from the accessory kit
● 1 T10 screwdriver
Procedure
Read the section "ESD guideline (Page 135)".
Removal
1. Switch off both on/off switches
⑥
.
The LED
⑤
extinguishes.
2. Plug in both power plugs
③
.
3. Switch on both on/off switches
⑥
.
The LED
⑤
lights up.
4. Secure the power plugs, if necessary, to prevent the power cables from becoming loose accidentally.
Remove the screw
①
.
5. Slide the power plug latch
②
over the plug
③
.
6. Fasten the power plug latch with the screw
①
.
Note
If only one power supply module is switched on or connected, or a module is defective, a warning signal is emitted. You cancel the warning signal by pressing the acknowledgment button
④
.
The status is also displayed and signaled by the SIMATIC monitoring software, if active. You can mute the acoustic alarm in the SIMATIC monitoring software.
WARNING
Risk of fire
When the power plug is secured with a latch, the power outlet must be freely accessible to allow the device to be easily removed from the mains.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
43
Installing and connecting the device
3.3 Connecting the device
Installation
Install the device in reverse order.
3.3.5 Connecting the device to networks
The following options are available for the integration in existing or planned system environments or networks:
Ethernet
PROFIBUS/MPI
The optional electrically isolated PROFIBUS interface (12 Mbps) can be used to interconnect distributed field devices or for coupling to SIMATIC S7.
The "SOFTNET for PROFIBUS" software package is required for coupling to S7 automation systems.
PROFINET
The integrated Ethernet port (10/100/1000 Mbps) can also be used for communication and data exchange with automation devices such as SIMATIC S7.
This functionality requires the "SOFTNET S7" software package.
PROFINET can be operated via
● CP1616 IRT (Isochronous Real Time)
● Standard Ethernet interfaces (RT)
CP 1616 on-board allows you to connect IPCs to Industrial Ethernet. Only one CP 1616 can
be installed in a PG/PC. You will find detailed information in sections "Connecting the device
to networks (Page 44)" and "Hardware description (Page 148)".
Device driver CP 16xx.sys
The device driver allow integration of the Windows network protocol in the optional "CP 1616 onboard" Ethernet PROFINET controller on SIMATIC PCs. The PROFINET interface will act like a regular 100 Mbit Ethernet interface with a MAC address when you use this driver. The three RJ45 sockets are connected with each other via switch.
PROFINET IO application
You can create, operate and configure PROFINET IO applications using the "Development
Kit DK-16xx PN IO. It must be installed in addition to the CP 16xx.sys device driver. This kit and the documentation are available free of charge at the following Internet address:
Development Kit DK-16xx PN IO
( http://www.automation.siemens.com/net/html_00/produkte/040_cp_1616_devlopkit.htm
)
44
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Installing and connecting the device
3.3 Connecting the device
SIMATIC NET
Use this software package to configure network components and connections. You will find information on this on the SIMATIC NET DVD. This software package and the documentation are not part of the product package.
Additional information
Additional information is available in the catalog and the online ordering system Industry Mall
( https://mall.industry.siemens.com
).
See also
Technical Support ( http://www.siemens.de/automation/csi_en_WW )
CP 1616 onboard
The basic characteristics of the PCS 1616 onboard are:
● Optimized for PROFINET IO
● With Ethernet realtime ASIC ERTEC 400
● Three RJ45 sockets for connection terminal devices or addition network components
● Integrated 3-port real-time switch
● Automatic hardware detection
NOTICE
A maximum of one CP 1616/1604 is permitted
A maximum of one CP 1616/1604 module can be installed in one PG/PC. If you want to use an additional CP 1616/1604 card, the CP 1616 onboard option must be disabled using the "Profinet" entry in the BIOS setup.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
45
Installing and connecting the device
3.3 Connecting the device
Additional documentation on PROFINET
Get an overview of the information available for PROFINET
( http://support.automation.siemens.com/WW/view/en/18880715/133300 ).
Document name What is contained in this document?
This documentation is not included in the product package:
Getting Started
PROFINET IO Getting Started: Manual
Collection
Manual
PROFINET System Description
The documents use concrete examples to provide step-by-step instructions on how to commission a fully functional application.
This gives you the basic knowledge about the PROFINET
IO topics:
Network components, data exchange and communication,
PROFINET IO, component-based automation, application example of PROFINET IO and component-based automation.
Manual
From PROFIBUS DP to PROFINET IO
Readme file for CP 1616/CP 1604 and
DK-16xx PN IO
Configuration Manual
Commissioning PC Stations
Manual
SIMATIC NET Industrial Communication with PG/PC: Volume 1 - Basics
SIMATIC NET Industrial Communication with PG/PC: Volume 2 - Interfaces
Read this document if you want to convert an installed
PROFIBUS system to a PROFINET system.
This provides the latest information about the
SIMATIC NET products CP 1616/CP 1604, CP 1616 onboard, the developer kit.
This provides you will all the information necessary for commissioning and configuring a PC as a PROFINET IO controller or IO device.
This manual introduces you to industrial communication and explains the available communication protocols. It also describes the OPC interface as an alternative to the
IO-based user programming interface.
S7 CPs for Industrial Ethernet
Configuring and Commissioning
Manual
SIMATIC NET - Twisted Pair and
Fiber-Optic Networks
This provides the following support:
- For commissioning S7 stations
- For establishing effective communication
Configure and build your Industrial Ethernet networks based on this document.
This documentation is part of the supplied Documentation and Drivers CD:
Operating instructions
CP 1616/CP 1604/CP 1616 onboard
This provides you with all information required for operation.
Installation guide
Device Driver CP16xx.sys
Read this guide if you want to install the NDIS device driver, CP16xx.sys.
Further information
You can find the information on specific products in the Internet at the address: Productrelated Information SIMATIC NET ( http://www.siemens.com/simatic-net )
46
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Installing and connecting the device
3.3 Connecting the device
3.3.6
3.3.6.1
Requirement
Securing the lines
Network and fieldbus cables
The strain relief included in the scope of delivery is used to prevent that the plug does not connect from the device.
Mounting is carried out instead of the fieldbus cover.
● 1 strain relief
● 1 T10 screwdriver
● 1 side cutter
● Cable ties
Procedure
The following procedure describes the mounting of a strain relief for fieldbus and network cables. Mounting of other strain reliefs is carried out analog. The sheet metal part required for mounting is included in the accessory kit.
1. Remove the marked screw and the fieldbus cover fastened with it.
2. Mount the strain relief.
Use the mounting screw of the fieldbus cover for this purpose.
3. Fasten the cables with cable ties to the cable strain relief.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
47
Installing and connecting the device
3.3 Connecting the device
3.3.6.2 COM, DP, DVI/VGA, PS/2 and audio lines
Cable ties that can be loosened for strain relief at the interfaces are enclosed in the accessory kit. These cable ties can be installed on the rear panel, if necessary.
Procedure
1. Push a removable cable tie into the device rear panel at the marked point.
The figure shows the correct cable tie mounting position.
3.3.7
2. Fasten the cables with the removable cable ties to the strain relief.
Multi-monitoring
You can operate up to five monitors simultaneously at the interfaces of the integrated graphics controller in combination with the optional graphics card. Parameter assignment is performed by means of the Control Panel in Windows.
The following monitors can be operated simultaneously on the motherboard:
● 2 × DisplayPort, 1 × DVI
● 2 × DisplayPort, 1 × VGA
● 1 × DisplayPort, 1 × DVI via DisplayPort-DVI adapter
1
, 1 × DVI
● 1 × DisplayPort, 1 × VGA via DisplayPort-VGA adapter
1
, 1 × VGA via DVI/VGA adapter
1
● 1 × DVI via DisplayPort-DVI adapter, 1 × DVI via DisplayPort-DVI adapter
2
, 1 × DVI
● 1 × VGA via DisplayPort-VGA adapter, 1 × VGA via DisplayPort-VGA adapter, 1 × VGA via DVI/VGA adapter
1 available as accessories
2 active DisplayPort-DVI adapter
Detailed information is available in section "Accessories".
Note
The motherboard supports up to one additional DVI monitor if it is connected by means of a passive DisplayPort-DVI adapter.
48
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Commissioning the device
4
4.1 General information on commissioning
NOTICE
Risk of damage to the device!
Make sufficient allowances for the device to acquire room temperature before you put it into use. If condensation has developed on the device wait at least 12 hours before you switch it on.
Note
Switching the device on
Depending on the device model, the power supply has either one or two on/off switches as a power switch.
If at least one of these on/off switches at the rear of the device is in position "1" (on), the device can be switched on using the on/off button at the front.
If all the on/off switches at the rear of the device are in position "0" (off), the device takes the least amount of power from the AC mains. The device cannot be switched on using the on/off button at the front in this case.
Both on/off switches must therefore be in the "0" position, especially for the model with redundant power supply. This is because the device is operational even with one active power supply module.
Requirements for commissioning
The following requirements have to be met before you can start commissioning:
● I/O devices, keyboard, mouse and monitor are connected.
● The power supply is connected.
● An operating system is installed.
The device can be supplied without an operating system. Information on installation of the operating system is available in the section "Installing the software".
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
49
Commissioning the device
4.2 Switching on the device
4.2
Procedure
Switching on the device
Following the initial switch on, the operating system is set up automatically on the device.
NOTICE
Faulty installation
If you change the default values in the BIOS setup or if you turn off the device during installation, you disrupt the installation and the operating system is not installed correctly.
The operating safety of the device and the plant is at risk.
Do not switch off the device during the entire installation process. Do not change the default values in the BIOS setup.
1. Set the on/off switch to position "1". Information on the position of the switch is available
in the section "Device views (Page 16)".
2. Press the on/off button.
The green "POWER" LED lights up. The module carries out a self-test. During the selftest, the following message appears:
Press <ESC> to go to the main BIOS menu
3. Wait for the message to disappear. Then Windows is started.
4. Follow the instructions on the screen.
Note
The following steps are only to be performed for initial startup of the device with factory settings.
5. Make the required region and language settings.
If you want your system language to be international, select English. Information on changing the regional and language settings at a later time is available in the section
"Setting up the language selection by means of the Multilanguage User Interface (MUI)".
Note
Once the operating system has been set up, the device may restart.
6. Type in the product key as required.
The product key is located on the "Certificate of Authentication" in the "Product Key" line,
see section "Identification data of the device (Page 34)".
Result
The interface of the operating system is displayed every time you turn on the device and after the startup routine.
50
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
4.3
Commissioning the device
4.3 Automatic switching on of the device
Automatic switching on of the device
In the BIOS setup, you can specify the behavior of the device when it is disconnected from the mains voltage. The following property is set as default:
● BIOS setup, "Advanced" menu, "Chipset Configuration" submenu, setup parameter "After
G3 On" to "Last State".
● After a power loss during operation, the device will automatically restart when the power returns.
● If the device was not in operation, it remains switched off when the power returns.
The mains voltage must have failed for at least 20 s for the power failure to be detected and for this defined action to be executed.
NOTICE
Unintentional reactions at power loss restart
Automatic startup, for example, after a power failure, can result in unintentional reactions of the machine or plant. This endangers the operation.
Take the BIOS setup entry "After G3 On" into consideration in the plant planning.
4.4 Notes on different device configurations
4.4.1 Opening the front door
CAUTION
Electrostatic-sensitive devices
The device contains electronic components which may be destroyed by electrostatic charge.
Before you open the front door, read the (ESD) guidelines for handling electrostaticsensitive devices.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
51
Commissioning the device
4.4 Notes on different device configurations
4.4.2 DVD burner drive
The DVD burner drive is an optional device feature. Recording methods supported by the disk drive:
● Disc-At-Once
● Track-At-Once
● Session-At-Once
● Packet writing
For additional information, refer to the technical specifications.
Software
In order to use full functionality of the DVD burner you do not need to install additional software under Windows. The software for the DVD burner is part of the mentioned operating systems.
If you are using a different operating system, ensure that the software required for the DVD burner is installed.
Operation
Note
When first starting the burner software, no disks should be inserted in the drive. Faulty data storage media can interrupt the automatic drive recognition. This makes it impossible to correctly display the possible burner functions.
Burner operation is only permitted in an environment free of shock and vibration.
NOTICE
Data errors during burning
It cannot be ruled out that vibrations in the environment and varying quality of raw discs could result in data errors when burning data media, even when no error message occurs.
Data comparison is the only guarantee that data has been written correctly. Perform data comparison each time you burn a disc.
See also
Technical specifications (Page 139)
52
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
4.4.3
Commissioning the device
4.4 Notes on different device configurations
Hard disks in removable rack
The hard disks in the removable drive bay can be replaced during operation in connection with RAID (hot swap).
Requirement
● A hard disk of the same interface type
The interface type of the hard disk is displayed on the front door. Always replace the defective hard disk with a new one of the same interface type and capacity.
● A key for the hard disk lock
Procedure
NOTICE
Damage to the hard disk and loss of data
When you remove the hard disk while data is being written to the hard disk, you may damage the hard disk and destroy data.
• Only remove the hard disk tray from the removable drive bay when the hard disk is inactive. Inactive means the hard disk status display of the removable drive bay is not flashing.
•
Observe the EGB guidelines.
1. Identify which hard disk the RAID controller has reported as being faulty (see status indicators).
2. Open the front panel.
3. Slide the cover
①
of the removable drive bay lock to the right.
The marked lock is exposed.
4. Open the lock with the appropriate key.
5. Fold out the tray bracket somewhat to the front and pull out the hard disk tray by the tray bracket.
6. Insert the hard disk tray with the replaced hard disk into the removable drive bay and push it all the way in.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
53
Commissioning the device
4.4 Notes on different device configurations
7. Fold back the tray bracket until it rests completely against the hard disk tray.
The power supply LED
②
must be on.
8. Slide the cover of the removable drive bay lock to the left.
9. Lock it with the appropriate key.
Note
Always lock the hard disk tray in the removable drive bay to ensure reliable operation of a device with removable drive bay.
4.4.4 System with two drives
The system with two drives is an optional feature for the device.
When the device ships, the second drive is connected to SATA port 1. This hard disk drive is not set up. This gives you the option of backing up your data to this hard disk drive. Refer to your order documentation for information on hard disk drive capacity.
Booting from the second hard disk drive
In order to allow booting from the second hard disk drive, you need to configure it as the primary boot device (Boot Option #1). To do this, make the following settings in your BIOS
Setup:
1. Select the "Boot" tab.
2. Select the first entry from the list in the "Boot Option Properties": "Boot Option #1" and press the Return key.
3. Select the corresponding drive (slave drive) in the "Boot Option #1" window, e.g.
STxxxxxxxxx, and press the Return key.
The second hard disk drive (slave drive) becomes the primary boot device.
Note
The drive letters for the partitions on both drives are assigned by the operating system in use. You can change these in the Control Panel as required.
54
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Commissioning the device
4.4 Notes on different device configurations
4.4.5 RAID systems
4.4.5.1 Manage RAID system
RAID system management functions
The RAID system is fully set up ex works. The installed SIMATIC diagnostic software is used to display the status of the RAID system. Additional software is not required. Detailed information on hard disk replacement is available in section "Expansion and parameter assignment of device", "Replace defective hard disk in RAID system".
Note
A hard disk can be synchronized at operating system level if a fault is detected. It may take a very long time to synchronize a new hard disk in the background, depending on the size of the hard disk and on the system load. It may take several hours or even days in the case of extremely high hard disk load. Guide value for the duration: < 3 h with 90% HDD system load and RAID5 with HDD 1 TB.
The safe system states RAID Level, for example, 1 are only reached once synchronization has been successfully completed. In addition, system performance may be limited in the case of a manually started maintenance operation until completion of the maintenance phase.
Note
Password protection for RAID setup
To prevent access to the Option ROM, follow these steps:
•
Set the supervisor password in the BIOS setup, "Security > Set Supervisor Password" menu.
•
Disable the keyboard operation during the BIOS self test (POST) in the BIOS setup,
"Security > Option ROM keyboard" menu.
Replacing a faulty drive in the RAID system
Replace the faulty drive with a new drive of the same type and capacity to return to the safe
RAID1 or RAID5 state after a fault.
The diagnostic software indicates the following:
● A defective drive
● Details of the functioning hard disk
The defective hard disk is displayed with port number. You can find detailed information on drive replacement in the following sections:
● "Commissioning the device", "Hard disks in the removable drive bay"
● "Expansion and parameter assignment of device", "Replacing a defective hard disk in the
RAID system".
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
55
Commissioning the device
4.4 Notes on different device configurations
Integrating a new hard disk
A hard disk is integrated automatically into the RAID if it fulfills one of the following requirements:
● The hard disk is brand new.
● The hard disk is set up as a global spare drive.
● The hard disk is set up as a specific dedicaded spare drive.
4.4.5.2 RAID1 system
This is a RAID1 system configuration (data mirroring with two drives). This means that if there is a defective hard disk or there are cable problems, the system can continue to operate in one channel and achieve a high degree of availability.
Note
You will find information about the RAID controller in the "Drivers\RAID-AHCI\Intel" or
"Drivers\RAID-AHCI\Adaptec" directory on the "Documentation and Drivers" DVD that ships with the product.
Additional information on RAID1 systems can be found in the section "Manage onboard
4.4.5.3 Hardware RAID system
SAS Hardware RAID adapter card with own CPU and cache memory:
● For applications with stringent requirements regarding negligible system effects of the
RAID system.
● With maintenance-free battery backup for high data reliability.
● The RAID controller with PCIe x8 interface occupies one PCIe x16 expansion slot of the device.
The adjacent slot must remain free, and a perforated slot bracket must be mounted to ensure cooling.
Requirements for Adaptec Storage Manager software
The following requirements must be met before you use the software for the first time during commissioning:
● 4 GB main memory
● The operating system is restarted.
● The operating system is password-protected.
● Login and password of the operating system and Storage Manager software are the same.
56
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Commissioning the device
4.4 Notes on different device configurations
The data backup takes place on two or three SAS hard disks. As a result, the system is able to continue operation in the event of a defective hard disk or port connection problems, thereby achieving high availability. An optionally available hot-spare drive increase the availability of the system.
) can further
①
Connection for the SAS data cable
②
Connection for Zero Maintenance Module (ZMM)
The installed RAID controller for the "Adaptec RAID ASR8405" module is displayed as follows in the BIOS:
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
57
Commissioning the device
4.4 Notes on different device configurations
Additional software and documentation
The following software documentation can be found in the "Drivers\RAID-AHCI\Adaptec" directory of the "Documentation and Drivers" DVD that ships with the product:
● Adaptec RAID Controller Quick Start Guide
The PDF file describes how you install the RAID controller and create a bootable RAID1 or RAID5 array. It also describes how you install the operating system and the controller driver on the array.
● Adaptec RAID Controller Installation and User Manual
The PDF file contains comprehensive information on installation and configuration of the
RAID adapter card and the connected devices.
● Adaptec maxView Storage Manager User Manual
The PDF file contains comprehensive information on installation and use of Adaptec maxView Storage Manager.
● Command Line Utility User Guide
The PDF file contains the user manual for the command line utility program and comprehensive information on the use of ARCCONF.
All required software is pre-installed. However, if necessary, you can install additional software from the supplied Documentation and Drivers DVD, which also contains the associated software description. In order to use the software, the operating system must be password-protected. The password must be assigned before the software is installed. In a correct installation, the operating system password and RAID software password are the same.
58
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Commissioning the device
4.5 Windows Action Center
4.5 Windows Action Center
Warning from the Windows Action Center
The Action Center checks the status of the device with regard to the important safety aspects listed below. If a problem is found, the Action Center provides recommendations on how you can better protect the device.
● Firewall: The Windows Firewall adds protection to the device by blocking network or
Internet access to the device by unauthorized users. The firewall is enabled in the delivery state.
● Antivirus software: Antivirus programs add protection to the device by searching for and eliminating viruses and other security threats. No antivirus software is installed in the delivery state.
● Automatic updates: Using the Automatic Update feature allows Windows to regularly search for the latest critical updates for the device and to install them automatically.
This option is disabled in the delivery state for Windows Server 2008 R2 and Windows
Server 2012 R2. You can enable or disable this option for Windows 7 during commissioning of Windows.
● User Account Control:User Account Control issues a warning when programs attempt to modify important Windows settings. You can then either acknowledge this warning or prevent the program from changing the Windows settings.
This option is disabled in the delivery state for Windows Server 2008 R2 and Windows
Server 2012 R2. This option is enabled in the delivery state for Windows 7.
4.6 Switching off the device
Shutting down the operating system
For Windows operating systems:
1. Right-click on the Windows desktop.
2. Press the key combination <Alt+F4>.
3. Select "Shutdown".
● Alternatively, briefly press the on/off button (unless otherwise configured in the power
options). Information on the position of the button is available in the section "Device views
For non-Windows operating systems:
● Briefly press the on/off button.
The operating system is shut down. The "POWER" LED goes out. The device is switched off but not fully disconnected from the mains voltage.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
59
Commissioning the device
4.6 Switching off the device
Fully disconnecting the device from mains voltage
WARNING
Risk of fire and electric shock
The on/off button and on/off switch do not fully disconnect the device from the mains. If the device is switched off with the on/off switch, there remains a risk of electric shock and fire hazard, for example, if the device or connection cables are damaged or if the device is used improperly.
Always fully disconnect the device from the mains voltage as described below before performing work on the device or when the device will not be used over an extended period of time.
If the device was not mounted in a control cabinet:
● Shut down the operating system and pull the power plug on the rear of the device.
If the device was mounted in a control cabinet:
● Shut down the operating system and switch the AC circuit breaker to "Off".
The device is switched off and fully disconnected from the mains voltage. No trickle current is flowing.
Hardware reset
You can perform a hardware reset to switch off the device when the operating system no longer responds to input from the keyboard or mouse. The operating system is not safely shut down in this case.
NOTICE
Risk of data loss
The device is restarted in the case of a hardware reset. Data in the main memory can be deleted. Data on the drive may be lost. The device may be damaged.
Perform a hardware reset only in the case of an emergency.
For all operating systems:
● Press the on/off button for more than 4 seconds. or:
● Press the Reset button. Information on the position of the button is available in the
section "Device views (Page 16)".
See also
60
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Extended device functions
5
5.1 Monitoring functions
5.1.1 Overview of the monitoring functions
The basic version of the device also provides monitoring functions. The following display, monitoring and control functions are available when the appropriate software is used:
● Temperature monitoring (overtemperature, low temperature, or cable break at a temperature sensor)
● Monitoring of drives with S.M.A.R.T. functionality
● Watchdog (hardware or software reset of the computer)
● Operating hours meter (information on total runtime)
● Hard disk status and status of the RAID system
SIMATIC IPC DiagBase software
Use the functions of the SIMATIC IPC DiagBase software included in the scope of delivery for local monitoring. Use the "DiagBase Management Explorer" application to obtain a clear overview of the controls. Use the DiagBase Alarm Manager to receive notifications about individual alarms.
Note
For more information on SIMATIC IPC DiagBase software functionality, please refer to the relevant Online Help.
SIMATIC IPC DiagMonitor software
SIMATIC IPC DiagMonitor is available on CD (not included in the scope of delivery). This monitoring software comprises:
● The software for the stations to be monitored.
● A library for creating user-specific applications.
Note
SIMATIC IPC DiagMonitor supports the device hardware as of version 4.4.3. Devices with
Adaptec Hardware RAID adapter card are supported as of version 4.4.4.
Older versions do not support the device hardware.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
61
Extended device functions
5.1 Monitoring functions
5.1.2 Temperature monitoring/display
Three temperature sensors monitor the temperature of the device at several positions:
● Processor temperature
● Temperature close to the RAM ICs/chips
● Temperature of the basic module
A temperature error is triggered when one of the three temperature values exceeds the set temperature threshold and the following reaction is initiated:
Reaction
"Temp" LED lit red.
Device fan at maximum speed. The power supply unit fan is controlled by the power supply unit.
The DiagBase or DiagMonitor software alerts the user.
Option
None
None
None
The temperature error is retained in memory until temperatures have fallen below the thresholds and it is reset by one of the following measures:
● Acknowledgment of the error message by the monitoring software
● Restart of the device
5.1.3
Function
Watchdog (WD) with LED
The watchdog is able to monitor program runtime and informs the user about the different reactions that are triggered if the user program does not respond to the watchdog within the specified monitoring time.
The watchdog is in idle state during power on of the device, or after a HW-RESET (cold restart). A WD reaction is not triggered while it is in idle state. However, an active watchdog interrupt remains after a restart and its active state is still indicated by the LED.
62
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Extended device functions
5.1 Monitoring functions
Watchdog reactions
The following reactions may be triggered if the watchdog is not retriggered within the set time:
Reaction
Switch watchdog LED to red
Trigger a PC reset
Output of DiagBase alarm messages
Option
None
Configurable
None
Note
For more information on the watchdog functions, contact Customer Support.
WD monitoring times
Set the monitoring times in SIMATIC Diagnostics Management as integer values in the range from 4 to 255 seconds.
Note
The watchdog will be retriggered if you change the watchdog time after the WD has been activated.
5.1.4 Fan monitoring
The operation of the front, CPU and power supply fans is monitored.
If a fan fails, the following reactions are triggered:
● The "FAN" status display lights up red.
● If the SIMATIC monitoring software is installed, a fan alarm is output.
The fan error remains stored until the cause has been rectified. You can reset the error message with one of the following measures:
● Acknowledge error message with SIMATIC IPC DiagBase or SIMATIC IPC DiagMonitor
● Short-term disconnection of the device from the power supply
● Shut down device
● Restart the device
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
63
Extended device functions
5.2 Active Management Technology (AMT)
5.1.5 Battery monitoring
The installed buffer battery has a service life of at least 5 years. The status can be checked with two-tier battery monitoring. The information can be read from an I/O register and evaluated.
When the first warning level is reached, the remaining service life of the battery for buffering
CMOS data and buffer memory is at least 1 month.
5.1.6 Drive monitoring
Default: SMART messages of the hard disks are reported.
RAID combination: The "Normal", "Degraded", "Rebuild" are displayed.
5.2 Active Management Technology (AMT)
AMT (Active Management Technology) is technology for the remote maintenance of computers (simply called AMT-PC in the remainder of the document) and it includes the following functions:
● Keyboard Video Mouse( KVM) Redirection: Using KVM that is integrated in the AMT hardware you access the AMT PC remotely. With KVM, you can also control AMT PCs that have no operating system or a defective operating system. A KVM remote session is always possible with the KVM server integrated in the firmware. This means you can restart the PC and change the BIOS setup remotely.
● Remote power management: AMT PCs can be turned on and off and restarted from another PC.
● SOL (Serial over LAN): Redirection of the data of a serial interface to the network. The main use of the function is text-based remote control of an AMT PC using a console.
● IDE redirection: An ISO file on the help desk PC can be mounted on the AMT PC and used as a DVD drive.
An ISO file contains a memory image of the content of a CD or DVD structured in the ISO
9660 format.
● Remote reboot: An AMT PC can be booted from a bootable ISO file made available by another PC.
64
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Extended device functions
5.2 Active Management Technology (AMT)
SIMATIC IPC Remote Manager
The "SIMATIC IPC Remote Manager" software is available for utilization of the AMT functions with SIMATIC IPCs. The software can be ordered from the Siemens online ordering system. For detailed information about "SIMATIC IPC Remote Manager", refer to the corresponding product documentation: SIMATIC IPC Remote Manager
( http://support.automation.siemens.com/WW/view/en/48707158 )
Typical areas of application and functions of the SIMATIC IPC Remote Manager:
● Remote maintenance of SIMATIC IPC with AMT, for example for service purposes in the case of a defective operating system or for adapting BIOS settings.
● Diagnostics without on-site use
● Convenient service: Access to AMT clients, such as headless systems, without additional hardware
● Resource management
Requirement
● A device with a Core i5 or Xeon processor
● A functioning and configured management engine
● A functioning and configured Ethernet connection
● A help desk PC with a functioning and configured Ethernet connection for the full AMT functionality
Configuration of the AMT PC
You configure AMT by means of the BIOS setup and MEBx (Management Engine BIOS
Extension). MEBx is a BIOS extension for configuration of AMT (see BIOS description in chapter "Technical specifications").
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
65
Extended device functions
5.3 Trusted Platform Module (TPM)
5.3 Trusted Platform Module (TPM)
Depending on the ordered configuration of your device, a Trusted Platform Module according to Standard 1.2 may be available. The Trusted Platform Module is a chip that enhances your device with security functions. It provides an improved protection from manipulation of the
PC. The current operating systems Windows 7 and Windows 8 support these security functions. You can enable the Trusted Platform Module in the "Security" menu in the BIOS
Setup. Please note the respective import and export provisions for the Trusted Platform
Module.
Using the Trusted Platform Module
The TPM can be used with the "BitLocker" drive encrypter, for example, in
Windows operating systems. Please follow the instructions for this in the operating system.
Note
Risk of data loss
If you lose the password for the drive encryption, you will not be able to restore the data. You will then lose accesss to the encrypted drive.
The warranty does not cover a reset of the hardware in the event of a loss of a password.
Please store the password carefully and make sure it is protected against unauthorized access.
66
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Expanding and assigning parameters to the device
6.1 Retrofitting instructions
Temperature range 0 °C to 35 °C
The maximum permissible power loss of the expansion cards amounts to 75 W.
Distribution to the slots without exceeding the total power:
● 25 W for the expansion cards in Slot 1, 2, 3, 4 maximum
Maximum permitted configuration
6
Note
During operation, the HDDs installed in the removable drive bay must not be exposed to vibratory loads and may only be exposed to limited shock loads (see Technical specifications).
Temperature range 0 °C to 40 °C
The maximum permissible power loss of the expansion cards amounts to 55 W.
Distribution to the slots without exceeding the total power:
● 25 W for Slot 1 maximum
● 25 W each for Slot 2, 3 maximum
● 15 W for Slot 4 maximum
Maximum permitted configuration
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
67
Expanding and assigning parameters to the device
6.1 Retrofitting instructions
An Slimline DVD RW drive can be installed optionally. This may only be operated under consideration of the following instructions.
CAUTION
Danger of data errors when burning data carriers (DVD RW)
Burning is permissible only in an undisturbed environment, i.e. shock and vibration stress must be avoided.
Because of heavy fluctuation in the quality of CD-Rs, data may be corrupted in a burning session, even if no error message is initially displayed.
The written data can only be verified by comparing these with the source. To be on the safe side, data should be verified after every burning session.
Note
During operation, the HDDs installed in the removable drive bay must not be exposed to vibratory loads and may only be exposed to limited shock loads (see Technical specifications).
Temperature range 0 °C to 45 °C
The maximum permissible power loss of the expansion cards amounts to 55 W. An ODD drive slimline is not permitted.
Distribution to the slots without exceeding the total power:
● 25 W for Slot 1 maximum
● 25 W each for Slot 2, 3 maximum
● 15 W for Slot 4 maximum
Maximum permitted configuration
Note
During operation, the HDDs installed in the removable drive bay must not be exposed to vibratory loads and may only be exposed to limited shock loads (see Technical specifications).
68
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Expanding and assigning parameters to the device
6.2 Removing the front panel
Temperature range 0°C to 50°C
The maximum permissible power loss of the expansion cards amounts to 30 W. An ODD drive slimline is not permitted and no HDD operation in the removable drive bay.
Distribution to the slots without exceeding the total power:
● 25 W for Slot 1 maximum
● 15 W for Slot 2 maximum
● 10 W for Slot 3 maximum
● 10 W for Slot 4 maximum
Maximum permitted configuration
Note
During operation, the HDDs installed in the removable drive bay must not be exposed to vibratory loads and may only be exposed to limited shock loads (see Technical specifications).
6.2
Requirement
Removing the front panel
Procedure
Observe the chapter "ESD guideline (Page 135)".
1. Open the front door at least 45°.
The interlock marked in the figure then releases the front panel.
2. Remove the front panel.
To do so reach into the fan slots.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
69
Expanding and assigning parameters to the device
6.3 Open the device.
6.3 Open the device.
NOTICE
Malfunctions and electric shock through repair
Improper repairs jeopardize operational reliability and damage the device.
The results are personal injuries and damage to the plant.
Take the following precautions:
• Always disconnect the power plug before you open the device.
•
Close the device after every repair.
Disclaimer of liability
All technical specifications and approvals apply only to expansions which are approved by the Siemens AG. We are not liable for functional limitations caused by the use of third-party devices or components.
Observe the installation instructions for the components. UL approval of the device only applies when UL-approved components are used according to their "Conditions of
Acceptability".
Requirement
● All connecting cables are unplugged
● The front panel is removed, see chapter "Removing the front panel (Page 69)".
● 1 T10 screwdriver
Procedure
Read the section "ESD guideline (Page 135)".
1. Loosen the marked screw and hit the screwdriver lightly with the ball of your hand to release the cover.
The screw remains captive in the housing.
2. Push the housing cover back and remove it.
70
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Expanding and assigning parameters to the device
6.4 Removing and installing memory modules
6.4 Removing and installing memory modules
Memory expansion options
1
2
3
4
The motherboard is equipped with 4 slots for memory modules. You can use DIMM DDR3 memory modules. Technology: Memory transaction rate 1333 MT/sec (PC3-10600),
1600MT/sec (PC3-12800), "unbuffered", "no ECC" or "with ECC". This allows you to expand
Rack PC memory up to 32 GB, of which you can use approx. 3.2 GB for the operating system and applications in case of 32-bit operating systems. You can install one, two or four modules.
Combination
Channel A (external) Channel B Maximum expansion
Slot X19
DIMM1-1
Slot X190
DIMM1-2
Slot X20
DIMM2-1
2 GB/4 GB/8 GB
Slot X200
DIMM2-2
2 GB/4 GB/8 GB 2 GB/4 GB/8 GB
Combinations of three memory modules are not permitted
8 GB
16 GB
2 GB/4 GB/8 GB 2 GB/4 GB/8 GB 2 GB/4 GB/8 GB 2 GB/4 GB/8 GB 32 GB
Note
• Memory modules with ECC and without ECC may not be used in mixed operation.
•
Only modules of the same module organization 2Rx8 or 1Rx8 may be used per channel.
• Memory is operated in dual-channel mode if two modules are installed.
•
If expansion cards with their own memory, for example, graphics cards with 256 MB or more are used, the memory available for the 32-bit operating system or applications may be less than 3.2 GB.
In order to avoid operating faults you may have to remove one or two memory modules or use a memory module with a smaller capacity so that the real memory expansion on the motherboard and the reserved memory of the expansion card do not overlap.
Requirement
● The device is opened.
● Remove the bus board, if necessary, for easier access to the memory modules.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
71
Expanding and assigning parameters to the device
6.4 Removing and installing memory modules
Procedure - installing a memory module
1. Install the memory modules in the following order:
1. DIMM 2-1
2. DIMM 1-1
3. DIMM 2-2
4. DIMM 1-2
2. Remove the memory module from its packaging.
Hold it by the upper edges only.
Note the indicated notch during insertion.
3. Insert the memory module in the slot perpendicular to the motherboard.
4. Press both sides of the memory module evenly to avoid jamming.
The memory module latches in audibly.
The memory module is inserted correctly if less than 1 mm of the gold contacts is visible evenly across the entire length of the module.
5. Close the device.
72
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Removing a memory module
1. Always remove the memory modules in the reverse order:
1. DIMM 1-2
2. DIMM 1-1
3. DIMM 2-2
4. DIMM 2-1
Expanding and assigning parameters to the device
6.5 Expansion cards
2. Open the two latches at the sides of the memory module evenly. Remove the memory module from the slot.
3. Close the device.
Display of the current memory configuration
The new memory configuration is detected automatically. The allocation of the ”base memory and extended memory” is automatically displayed when you switch on the device.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
73
Expanding and assigning parameters to the device
6.5 Expansion cards
6.5 Expansion cards
6.5.1 Notes on the expansion cards
Slot numbering
The 4 existing slots can be identified on the basis of the embossed numbers that are marked in the following figure.
Slot
1
2
3
4
4 x PCIe device version 2 x PCIe device version 2 x PCI/2 x PCIe device version
PCIe Gen3 8 Lane - PCIe Gen3 8 Lane
PCIe Gen3 4 Lane PCIe Gen3 4 Lane PCI
PCIe Gen2 4 Lane
PCIe Gen3 4 Lane
PCIe Gen2 4 Lane
-
PCI
PCIe Gen3 8 Lane
Note
Information about specifications
The device is designed for use with expansion cards to PCI specification 2.3 or PCIe specification 1.0a. PCI expansion cards with a 5 V and 3.3 V power supply can be operated.
Compliance with the defined mechanical defaults is imperative. Failure to comply with these defaults can result in contact problems, malfunctions and assembly difficulties. The permitted
74
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Expanding and assigning parameters to the device
6.5 Expansion cards
Note about long PCI / PCIe expansion cards
To insert long PCI / PCIe expansion cards into the guide rails, they must be equipped with a retainer.
Note on PCI-Express expansion cards
The expansion cards in the PCIe slot 1 can take up two slots.
Note on PROFINET expansion cards
The "CP 1616 onboard" option must be disabled in the BIOS for devices with CP 1616 onboard, before a PROFINET module (such as a CP 1616) can be installed in the system.
6.5.2 Removing and installing bus frame
The feet on the bus frame shown in the following figure serve as a mounting aid and allow vertical mounting. You may have to support the bus frame with your hand to prevent it from tipping.
Requirement
● The device is open in accordance with section "Open the device. (Page 70)".
Procedure
Read the section "ESD guideline (Page 135)".
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
75
Expanding and assigning parameters to the device
6.5 Expansion cards
Removal
1. Remove the 4 marked screws.
2. Pull the bus frame evenly from the unit at the marked points.
Do not tilt the bus frame when removing it.
3. Place the bus frame upright.
Support the bus frame with your hand to prevent it from tipping.
4. Unlock the marked plug and pull out the connector downwards.
Installation
To install the bus frame follow the steps for removing it in reverse order.
6.5.3
Requirement
Removing and installing expansion cards
● 1 T10 screwdriver
● 1 side cutter
● 1 retainer from the accessory kit
You may only use latching retainers of the same type.
Latching retainers are available under the Order Number A5E02719654.
● 1 mounting bracket for low expansion cards included with the retainers in the accessory kit.
76
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Expanding and assigning parameters to the device
6.5 Expansion cards
Procedure
Note
Mounting bracket for low expansion cards
To guarantee the stable installation of a low expansion card, you need an additional mounting bracket for latching retainers. The mounting bracket may have to be removed when you replace the low expansion card with a high one.
Installation
1. Remove the marked screw.
2. Swing the top edge of the bus frame towards the arrow direction and remove the front slot plate.
3. If you want to install the expansion card into the rear slot, remove the marked screw and then the rear slot plate.
4. Insert the expansion card into the slot in the arrow direction.
Slide the expansion card into the slot until it stops without being skewed.
Secure the expansion card at the marked point with the corresponding screw.
5. If required, fasten the shown support bracket with 2 expansion rivets to the bus frame, in particular at low-profile expansion cards.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
77
Expanding and assigning parameters to the device
6.5 Expansion cards
6. Insert the retainer
①
through one of the marked guide slots
②
.
If possible, use the guide slot closest to the edge-socket connector.
The retainer can only be moved in the direction of the expansion card.
The retainer latches into the selected position.
If you want to change the position subsequently, you have to open the top edge of the bus frame.
7. Press the retainer onto the expansion card. But only so that the retainer touches the expansion card and does not damage it.
While doing this, adjust the expansion card so that it fits into the slot of the retainer. Pay attention to the notch of the expansion card.
8. Cut off the protruding part of the retainer as shown.
Do not leave any remnants jutting out.
9. Insert the front slot plate again.
Swivel the top side of the bus frame back into the original position and secure the top side of the bus frame with the marked screw.
Removal
For installation, follow the steps for removal in reverse order.
The retainer can only be moved in the direction of the expansion card. To remove the retainer open the longitudinal side of the bus frame and pull out the retainer inwards.
78
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Further procedure
See also
Expanding and assigning parameters to the device
6.5 Expansion cards
6.5.4 Removing and installing the Hardware RAID adapter card
6.5.4.1
Requirement
Requirement
For installation of the Hardware RAID adapter card, you require the following:
● A T10 screwdriver
● The Hardware RAID adapter card with connection for the SAS data cable connection for the capacitor block of the ZMM
②
①
and
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
79
Expanding and assigning parameters to the device
6.5 Expansion cards
● A capacitor block of a maintenance-free battery backup module (ZMM)
①
Capacitor block
②
Extension, for IPC847D
● An adapter cable for connection of the hard disk drive
①
to the RAID module
80
Observe the numbering of the connections
②
.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Expanding and assigning parameters to the device
6.5 Expansion cards
NOTICE
Capacitor block must be discharged
When you remove or install a charged capacitor block, the components of the RAID adapter card may be damaged, resulting in data loss.
Remove or install a capacitor block only in completely discharged condition. The Siemens genuine spare part is supplied with discharged capacitor block.
Discharge an installed capacitor block as follows:
1. Shut down the operating system properly.
2. Disconnect the device from the supply system.
3. Wait at least 10 minutes.
If the capacitor is not discharged, a yellow LED close to the connector lights up.
4. Only remove the connector when the yellow LED is extinguished.
6.5.4.2 Procedure
Procedure for IPC647D
This section describes the installation of the Hardware RAID adapter card with capacitor block for the SIMATIC IPC647D.
1. Disconnect the device from the supply system.
2. Remove the bus frame.
3. Connect the adapter cable to the appropriate existing drives. Loosen the screws for the power unit if necessary.
•
Plug in the adapter cable as follows:
– Connector 0 in drive 0
– Connector 1 in drive 1
• Make sure that the connector latch engages.
•
Run the adapter cable S-shaped to the front and from there to the expansion card.
The cable is laid in the front area under the bus frame in the final assembled state.
• First plug the adapter cable into the RAID module, if the bus frame is mounted.
The HDD cables are not attached to the drive rack in this case.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
81
Expanding and assigning parameters to the device
6.5 Expansion cards
4. Secure the capacitor block to the bus frame with two cable ties.
Make sure that the locks of the cable tie, as indicated, are installed in the plug-in direction in relation to the motherboard.
Ensure that the cable is not damaged during installation.
5. Install the RAID adapter card in slot 1. The adjacent slot must be free. The free slot is sealed with a perforated slot bracket to ensure cooling.
6. Secure the RAID adapter card with the holder.
7. Insert the capacitor block cable connector at the marked position.
The connector snaps into place.
8. Install the bus frame in the housing. Ensure that no cables are crimped when inserting.
9. Make the connection between the RAID adapter card and adapter cable as follows:
Insert the adapter cable at the marked position (viewed from below).
Make sure that the connector latch audibly engages.
For removal, follow the steps in reverse order.
82
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
6.5.4.3
Expanding and assigning parameters to the device
6.5 Expansion cards
Configuring the Hardware RAID adapter card
Note
Management of the Hardware RAID system
When setting up the Hardware RAID system, set the write cache of the RAID controller as follows (see the additional documentation of Adaptec):
•
Write Caching - Enable with Backup Unit
• create RAID via: Build/Verify
After replacement of the RAID adapter card, configure it in the BIOS setup as follows:
Note
The key combination <CTRL+A> is only effective in "Legacy" mode. If the "Boot Type" parameter is set to "UEFI Boot Type in the "Boot" menu in the BIOS setup, the RAID hardware is configured by using the "Device Management" button in the BIOS selection menu.
1. Switch on the device.
2. During the boot phase, press the key combination <CTRL+A> when prompted to do so.
If the "Boot Type" parameter is set to "Dual Boot Type" in the "Boot" menu in the BIOS setup and an EFI boot medium is available, you must press the <ENTER> key after having pressed the <CTRL+A> within 1 second.
The system starts if you do not press the <ENTER> key in time.
3. Assign the parameters under "Controller Configuration" as follows:
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
83
Expanding and assigning parameters to the device
6.6 Drives and storage media
6.6
6.6.1
Note
The settings shown correspond to the default setting in the delivery state of the device.
Difference in the parameters compared to the default setting of the Hardware RAID adapter card after replacement:
•
"Drives Write Cache = Disabled", which means the write cache of the hard disk is switched off.
• "Alarm Control = Disabled", which means the acoustic alarm in case of a fault is switched off
Drives and storage media
Overview
You can mount the following drives and storage media in the device:
● Hard disk drive
● Solid State Drive
● DVD drive
There are two drive cages for alternative installation:
● Drive cage for removable drive bays
● Vibration-damped drive cage
84
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Expanding and assigning parameters to the device
6.6 Drives and storage media
Drive cage for removable drive bays
The drive cage is used to hold removable drive bays with inserts for drives, for example
HDDs and SSDs. A Slimline DVD drive can be mounted in the lower drive bay.
①
Removable drive bay with trays for drives
②
Slimline mounting bay for DVD drive
③
Drive cage for removable drive bays
Vibration-damped drive cage
The drive cage contains shock and vibration-attenuating components for holding hard disk drives. A Slimline DVD drive can be mounted in the lower drive bay.
①
Two drive bays
②
Slimline mounting bay for DVD drive
③
Vibration-damped drive cage
6.6.2
Requirement
Removing and installing drive cage
● The device is open, see the section "Open the device. (Page 70)".
● Applies for vibration-damped drive cage:
The bus frame has been removed, see chapter "Removing and installing bus frame
● 1 T10 screwdriver
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
85
Expanding and assigning parameters to the device
6.6 Drives and storage media
Procedure
Read the section "ESD guideline (Page 135)".
Removal
1. Remove the marked screws.
2. Remove the marked screws.
3. Note the positions of the marked
SATA connector.
Press the unlock mechanism of the connector shown on the right in the figure and pull off the connector.
Pull off the power supply connector of the Slimline drive marked on the right, if a Slimline drive exists.
86
4. Slide the drive cage toward the power supply until it is released from the front frame and remove the drive cage from the device.
Installation
To install the fan, follow the steps for removing it in reverse order.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Expanding and assigning parameters to the device
6.6 Drives and storage media
6.6.3
Requirement
Removing and installing drive fans
● The device is opened.
Note
Install only a fan of the same type. Information about the original spare parts for SIMATIC
PCs is available in the Internet at After-sales information system for SIMATIC PC/PG
( http://www.siemens.com/asis ).
Install the drive fan as seen in the figure. The drive fan blows cooling air into the housing.
Procedure
Note
The drive cage has been removed so that the work steps can be more easily seen.
Removal
1. Press on the clip
①
at the small power supply plug and pull the plug to the top from the larger adapter plug.
2. Put your hands into the indentations on the left and right of the fan retainer and slide the fan retainer together with the drive fan guides.
②
up and out of the
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
87
Expanding and assigning parameters to the device
6.6 Drives and storage media
Installation
1. Slide the power supply plug into place.
①
into the adapter plug until it snaps
2. Slide the fan retainer together with the drive fan
②
first under the top two and then under the bottom two guides marked in red until the fan retainer is flush with the top edge of the drive cage.
Make sure that you do not jam the fan retainer. The fan retainer is flush against the drive cage when installed.
Removing the adapter plug
If necessary, remove the adapter plug, for example, when removing the drive cage.
1. To do so, press on the clips
①
on the side of the adapter plug and remove the plug by pulling it down.
88
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
6.6.4
Expanding and assigning parameters to the device
6.6 Drives and storage media
Removing and inserting the tray from the removable drive bays
There are trays in the removable drive bays that are installed in the drive cages. Hard disks or SSDs can be installed in the tray.
Requirement
● The front door is open
● 1 key
Procedure
Removal
1. Slide the cover of the locking mechanism of the removable drive bay in the direction of the arrow.
2. Use the appropriate key to unlock the tray on the removable drive bay.
3. Open the handle on the removable drive bay and open it at the highlighted spot in direction of the arrow until you feel a slight resistance.
4. Now grasp the handle to the right of the notch you used to pull out the handle and pull the tray completely out of the removable drive bay.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
89
Expanding and assigning parameters to the device
6.6 Drives and storage media
Installation
To install the fan, follow the steps for removing it in reverse order.
Note
The tray must always be locked in the removable drive bay to ensure reliable operation of the devices with removable drive bays.
6.6.5 Removing and installing the hard disk drive from a tray
Requirement
● 1 drive
● 1 soft mounting padding
Procedure
Observe the chapter "ESD guideline (Page 135)".
Removal
1. Place the tray as shown on the mounting padding.
2. Remove the marked screws.
Installation
Proceed in reverse order. Use only the original screws during installation. Position all screws first and do not tighten them until all screws are installed in the thread.
90
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Expanding and assigning parameters to the device
6.6 Drives and storage media
6.6.6
Requirement
Removing and installing a drive from a drive cage
This chapter describes the removal and installation of the following drive types from the drive cage or the vibration-damped drive cage:
● Hard disk drive
● Removable drive bay
● DVD drive
Removal and installation of a Slimline DVD drive is carried out analog.
● The drive cage has been removed, see chapter "Removing and installing drive cage
● The drive fan has been removed, see chapter "Removing and installing drive fans
● The connecting cables have been removed from the drive.
Procedure
Read the section "ESD guideline (Page 135)".
Removal
1. Position the drive cage as shown.
2. Remove the marked screws of the both sides of the drive cage.
4. Pull the removable drive bay out of the drive cage in the direction of the arrow.
Installation
To install the fan, follow the steps for removing it in reverse order. Use only the original screws during installation.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
91
Expanding and assigning parameters to the device
6.6 Drives and storage media
6.6.7 Replacing a defective hard disk drive in the RAID system
Hard disk drives can be replaced during operation in the removable drive bay in connection with a configured RAID system. This functionality is referred to as "Hot Swap".
Note
If you have configured a non-RAID system with several hard disk drives, you need to turn off the device before you replace a hard disk drive.
CAUTION
Damaging the drive
If you replace a drive while it is active, the drive and data are corrupted. The device can no longer be operated without problems.
Replace the drive in the removable drive bay when the "HDD" status display of the device is not lit.
Observe the EGB guidelines. Always replace the drive with a new drive of the same type and capacity.
Mounting locations for hard disk drives in the RAID1 system
Hard disk drives for a RAID system can be installed either in the device or on the front in the removable drive bay.
Note
The replacement of a hard disk drive with removable drive bays and in the RAID system can be performed without shutting down the device. An internal hard disk drive may only be replaced when the device is switched off.
The new hard disk drive can be integrated into the RAID1 system at operating system level with the RAID software. Synchronization may take several hours, depending on system load.
Status displays of the hard disk drives in a RAID1 system
The following table includes information on the alarms of the status displays. If the hard disk drive is defective and the SIMATIC monitoring software is installed, the LEDs of the status display light up individually or simultaneously.
Internal hard disk drive or hard disk drive in removable drive bay
Status display
HDD0 alarm
HDD1 alarm
RAID BIOS
Port 0
Port 1
RAID software
Device port 0
Device port 1
Data cable connection
0
1
Drive
0
1
92
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Expanding and assigning parameters to the device
6.6 Drives and storage media
Replacing a defective hard disk drive in the RAID system
1. Determine which hard disk was reported by the RAID software as defective.
2. Replace the defective hard disk.
3. Replace the defective hard disk with a hard disk of the same type and capacity.
6.6.8 Removing and installing an SSD
6.6.8.1
Requirement
Removing and installing an SSD from a tray
● The connecting cables have been removed from the SSD.
● 1 soft mounting padding
Procedure
Observe the chapter "ESD guideline (Page 135)".
Removal
1. Place the tray as shown on the mounting padding.
2. Remove the marked screws.
Installation
For installation, follow the steps for removal in reverse order. Use only the original screws during installation. Position all screws first and do not tighten them until all screws are installed in the thread.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
93
Expanding and assigning parameters to the device
6.6 Drives and storage media
6.6.8.2
Requirement
Removing and installing an SSD with mounting plate from a drive cage
● The drive cage has been removed, see chapter "Removing and installing drive cage
● The drive fan has been removed, see chapter "Removing and installing drive fans
● 1 T10 screwdriver
Procedure
Read the section "ESD guideline (Page 135)".
Removal
1. On both sides of the drive cage, loosen the two screws that secure the mounting plate in the drive cage.
2. Pull out the mounting plate with the
SSD from the drive cage in the direction of the cables.
Do not pull on the cables.
3. Remove the marked screws.
4. Remove the mounting plate from the
SSD.
94
5. Pull out the plug from the SSD.
Installation
To install the fan, follow the steps for removing it in reverse order. Use only the original screws during installation.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Device maintenance and repair
7
7.1 Repair information
Carrying out repairs
Only qualified personnel are permitted to repair the device.
WARNING
Unauthorized opening and improper repairs on the device may result in substantial damage to equipment or endanger the user.
•
Always disconnect the power plug before you open the device.
•
Only install system expansion devices designed for this device. If you install other expansion devices, you may damage the device or violate the safety requirements and regulations on RF suppression. Contact your technical support team or where you purchased your PC to find out which system expansion devices may be installed.
If you install or exchange system expansions and damage your device, the warranty becomes void.
CAUTION
Electrostatic sensitive devices (ESD)
The device contains electronic components which are destroyed by electrostatic charges.
This can result in malfunctions and damage to the machine or plant.
Make sure you take precautionary measures even when you open the device, for example, when opening device doors, device covers or the enclosure cover. For more information, please refer to the chapter "ESD directives".
Limitation of liability
All technical specifications and approvals of the device only apply if you use expansion components that have a valid CE approval (CE mark). The installation instructions for expansion components in the associated documentation must be observed.
UL approval of the device only applies when the UL-approved components are used according to their "Conditions of Acceptability".
We are not liable for functional limitations caused by the use of third-party devices or components.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
95
Device maintenance and repair
7.2 Maintenance
Tools
You can make repairs on the device with the following tools:
● T20 screwdriver for protective conductor connection and enclosure
● T6 screwdriver for removing and installing the DVD drive
● T10 screwdriver for all of the remaining screws
See also
Spare parts and repairs ( http://support.automation.siemens.com/WW/view/en/16611927 )
7.2
7.2.1
Maintenance
Maintenance intervals
To maintain high system availability, we recommend the preventative replacement of those
PC components that are subject to wear in accordance with the intervals for replacement indicated in the table below.
Component
Drives
Backup battery
Device fan
Filter pad
Replacement interval
3 years
5 years
3 years
Depending on the degree of soiling
7.2.2 Changing the filter pad
Requirement
● The device is disconnected from the power supply, see chapter "Switching off the device
● The front panel is open, see chapter "Removing the front panel (Page 69)".
● A filter mat
You may only use filter mats of the same type. Information about original spare parts for
SIMATIC IPCs is available on the Internet at:
SIMATIC IPC after-sales information system ( http://www.siemens.com/asis ).
Order no.: A5E02396171; 10 pieces per package
96
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Procedure
Removal
1. Remove the filter mat front panel.
①
from the
Device maintenance and repair
7.3 Manage onboard RAID system
Installation
Note
Note the following points:
•
Use a new filter mat
• If you nevertheless use the removed filter mat, remember the direction in which the fans draw in air. Do not fit the outer side of the filter mat on the inside. Generally, the outer side is dirty after it has been in use for some time.
1. Insert the new filter mat in the front panel as shown.
2. Insert the front panel.
3. Close the front door.
7.3 Manage onboard RAID system
The RAID system is fully set up ex works. The installed SIMATIC diagnostic software is used to display the status of the RAID system. Additional software is not required. Additional
In "Legacy" mode, you can configure RAID hardware with <CTRL+I> in the boot phase. The associated description is available on the "Documentation and Drivers" DVD.
Note
The key combination <CTRL+I> is only effective in "Legacy" mode. If the "Boot Type" parameter is set to "UEFI Boot Type in the "Boot" menu in the BIOS setup, the RAID hardware is configured by using the "Device Management" button in the BIOS selection menu.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
97
Device maintenance and repair
7.3 Manage onboard RAID system
7.3.1 Example for a RAID1 system during the boot phase of the system
7.3.2 RAID software
Die RAID software "Intel Rapid Storage Technology" offers advanced functions to use and manage the RAID system.
1. Select the RAID software via "Start > Programs > Intel Rapid Storage Technology".
98
2. Select "Manage" > "Advanced" to display details of the RAID system.
3. Select "Help" > "System Report" > "Save" to create a report with the details of the RAID system.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
7.3.3
Device maintenance and repair
7.3 Manage onboard RAID system
Checking the status of the RAID system
By default, the status of the RAID system is displayed in the Windows Event Viewer and in a log file of the program. If an error occurs, a hard disk can be synchronized at the operating system level.
Note
It may take a very long time (hours or even days in the case of a high drive load) to synchronize a new hard disk in the background, depending on its size and on the system load.
The redundant system state is reached again only after synchronization is completed.
NOTICE
Operator errors on the machine or plant
Data is synchronized if a hard disk fails. Depending on the work load of the processor and hard disks, the system may react with some delay. Execution of keyboard, mouse or touch screen commands may be briefly delayed in extreme situations. This could result in operator errors on the machine or plant.
Do not operate safety-critical functions when a hard disk has failed.
7.3.4 Displaying a defective hard disk of a RAID system in the RAID software
Note
Always replace the defective hard disk with a new hard disk of the same type and capacity.
If an error is detected the defective hard disk must be replaced with a new hard disk to return to a secure RAID status after an error.
The RAID software indicates the following:
● A defective hard disk
● Details of the functioning hard disk:
The functioning hard disk is indicated by BIOS with its port number or by the RAID software with its device port number.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
99
Device maintenance and repair
7.3 Manage onboard RAID system
The following figure shows the corresponding window in the RAID software with a RAID1 system.
7.3.5
7.3.6
You can find information on how to detect and replace a defective hard disk in the RAID
system in the section "Replacing a defective hard disk drive in the RAID system (Page 92)".
Special feature: Replacing hard disk in the RAID system when switched off
The RAID system does not automatically boot up when restarted if a defective hard disk was replaced while the RAID system is switched off. Therefore, place the RAID system in the first place of the bootable sources in the BIOS setup menu "Boot". Otherwise, the system will boot from the hard disk you have just installed and the message "Operating system not found" will be displayed.
Integrating a new hard disk drive in the RAID system
The RAID system is configured in the delivery state so that a new hard disk must be integrated manually in case of an error. To integrate the hard disk automatically, activate
"Automatic rebuild" in the "Preferences" menu of the RAID software.
100
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Device maintenance and repair
7.3 Manage onboard RAID system
Automatic integration of a hard disk
NOTICE
Data loss
The hard disk to be integrated is not checked for partition information or existing data during automatic integration.
All partitions and data on the hard disk are deleted without warning. Insert only a brand-new hard disk.
Requirement:
● "Automatic rebuild" is selected in the "Preferences" menu of the RAID software.
● The hard disk must be completely new or set up as spare drive for this purpose. Notes on creating spare drives are available in the controller documentation.
Sequence
The following figure is an example for the automatic rebuilding process.
A defective hard disk is still displayed during the rebuilding process. This display disappears when the rebuilding process is completed.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
101
Device maintenance and repair
7.4 Managing the Hardware RAID system
Procedure - integrating hard disk manually
When the "Automatic rebuild" option is deselected in the "Preferences" menu of the RAID software (default setting), you must integrate the hard disk manually:
1. Select "Start" > "Programs" > "Intel Rapid Storage Technology".
2. Click "Run Hardware Scan now".
Or:
The new hard disk is found and displayed.
1. Reboot the device.
The RAID software automatically integrates the hard disk.
2. Click the "Rebuild to another Disk" link.
The RAID system is synchronized.
The following figure shows the window when integrating a hard disk in a RAID1 system.
102
If you shut down and restart the system without installing a functioning new hard disk,
"unused" is displayed for the corresponding SATA port. You can install the functioning hard disk while the system is running. The new hard disk is then assigned to a SATA port and is integrated into the RAID system.
A defective hard disk is still displayed during the rebuilding process. This display disappears when the rebuilding process is completed.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
7.4
7.4.1
Device maintenance and repair
7.4 Managing the Hardware RAID system
Managing the Hardware RAID system
The RAID system is fully set up ex works. The installed SIMATIC diagnostic software is used to display the status of the RAID system. Additional software is not required. Additional
Calling Adaptec maxView Storage Manager
The Internet Explorer opens when you call the Adaptec maxView Storage Manager for the first time. The following message is displayed depending on the operating system:
● Windows 7 32-bit/64-bit, Windows Server 2008 R2, Windows Server 2012 R2: "There is a problem with this website's security certificate".
● Windows Server 2008 R2, Windows Server 2012 R2: "Content from the website listed below is being blocked by the Internet Explorer Enhanced Security Configuration. https://127.0.0.1"
You can find step-by-step instructions on installing the certificate and setting up the trusted sites on the Internet at the following address: Details: Instructions for calling the Adaptec maxView Storage Manager
( http://support.automation.siemens.com/WW/view/en/102295361 )
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
103
Device maintenance and repair
7.5 Removing and installing hardware
7.5 Removing and installing hardware
7.5.1 Replacing device fans
Requirement
● The front panel is removed, see chapter "Removing the front panel (Page 69)".
● 1 or 2 fans
Procedure
Read the section "ESD guideline (Page 135)".
Removal
1. Release the knurled screw of the fan holder and remove the fan holder from the housing.
2. Press at the side of the clips of the fan connector to unlatch and pull the connector forward from the socket.
104
3. Loosen all the expanding rivets and remove the device fan from the fan holder.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Device maintenance and repair
7.5 Removing and installing hardware
Installation
Note
Install only fans of the same type. Information about original spare parts for SIMATIC PCs is available on the Internet at: SIMATIC IPC after-sales information system
( http://www.siemens.com/asis )
Ensure that the arrow on the device fan points away from the fan bracket. The device fan blows air into the enclosure.
To install the fan, follow the steps for removing it in reverse order.
Ensure that position of the fans are the cable routing are correct, see the figure in the
"Removal" section, Step 2. Make sure that the cables are not squashed or block the fan.
Furthermore take the positioning aids shown in the following figure into account. The fan holder must lie level on the front frame.
Further procedure
1. Install the front panel in accordance with chapter "Removing the front panel (Page 69)".
2. Test proper functioning of the fan using the DiagBase software.
7.5.2 Replacing the backup battery
The battery is used to back up the CMOS data for the BIOS setup and the real-time clock.
Note
Note the following points:
•
Check the maintenance interval.. You can find additional information in the section
"Maintenance intervals (Page 96)".
• Replace the lithium battery only with an identical one or a type recommended by the manufacturer. Information about original spare parts for SIMATIC IPCs is available on the
Internet at:
SIMATIC IPC after-sales information system ( http://www.siemens.com/asis )
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
105
Device maintenance and repair
7.5 Removing and installing hardware
Requirement
● The current BIOS Setup settings, see chapter "BIOS description (Page 186)".
● The device is open, see the section "Open the device. (Page 70)".
● All connection cables are unplugged.
● 1 battery, Order Number A5E00047601
Procedure
Read the section "ESD guideline (Page 135)".
CAUTION
Risk of short circuit
Conductive materials cause a battery short-circuit or damage adjacent modules.
Do not use tools made of conductive materials to replace the battery.
Note
The configuration data of the device may be deleted when you replace the backup battery, depending on BIOS settings. The configuration data are retained in the BIOS "Profile: User" setting; only the date and time must be set again.
106
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Removal
1. Remove the battery from the socket.
To do so hold at the points marked with the arrows and lever the battery out.
2. Dispose of the battery properly.
Device maintenance and repair
7.5 Removing and installing hardware
Installation
1. Press the new battery centered into the socket applying slight pressure.
Ensure that the battery is then held by the 4 brackets.
Further procedure
● Install the bus frame in accordance with chapter "Removing and installing bus frame
● Connect all cables.
● Close the device as specified in chapter "Open the device. (Page 70)".
● Set the BIOS setup.
The configuration data of the device may be deleted when you replace the backup battery, depending on BIOS setup settings.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
107
Device maintenance and repair
7.5 Removing and installing hardware
7.5.3 Replace AC power supply
Requirement
● The device is open, see the section "Open the device. (Page 70)".
● The power connector has been removed, see chapter "Connecting an AC power supply
● The bus frame has been removed, see chapter "Removing and installing bus frame
● T10 screwdriver
● Cable ties
Procedure
Read the section "ESD guideline (Page 135)".
Removal
1. Remove the cable ties that secure the cables in the housing.
2. Remove the marked screws.
3. Push the power supply unit towards the drive cage and lift it out of the device.
108
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Device maintenance and repair
7.5 Removing and installing hardware
Installation
Install the device in reverse order.
See also
Connection information (Page 38)
7.5.4
Requirement
Replacing the redundant power supply module
This work is required if a malfunction or a fault was reported for the redundant power supply.
The LED of the defective module is not lit up then (see chapter "Device views (Page 16)").
Note
If a module of the redundant power supply is defective, the device continues to function with the second module that is not defective. To ensure the availability of your system by means of the redundant power supply, shut down the device as soon as possible correctly and replace the defective module.
● The device is disconnected from the power supply, see chapter "Switching off the device
● 1 crosstip screwdriver
Procedure
Read the section "ESD guideline (Page 135)".
Removal
1. Remove the marked screw at the defective module.
2. Pull out the defective module from the frame using the hinged handle.
3. Insert the new module and secure it with the screw.
4. Reconnect the power supply cables.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
109
Device maintenance and repair
7.5 Removing and installing hardware
7.5.5
Requirement
Replacing the redundant power supply completely
● The device is disconnected from the power supply, see chapter "Switching off the device
● The device is open, see the section "Open the device. (Page 70)".
● The bus frame has been removed, see chapter "Removing and installing bus frame
● 1 spare part "Redundant power supply"
● 1 T10 screwdriver
● 1 crosstip screwdriver
● 2 cable ties
Procedure
Read the section "ESD guideline (Page 135)".
110
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Device maintenance and repair
7.5 Removing and installing hardware
Removal
1. Remove the modules of the redundant power supply, see chapter
"Replacing the redundant power supply module (Page 109)".
2. Remove the marked screws.
3. Loosen the two screws
①
and
②
.
Do not remove the screws completely. This facilitates subsequent reassembly. The power supply can still be pulled out.
3. Cut through the indicated cable ties.
Ensure that no cable is damaged while doing this.
4. Loosen all connectors of the power supply lines that connect the redundant power supply with drives and the motherboard. This includes:
• Power supply connectors of the drives
③
and
④
•
Power supply connector of the motherboard
⑤
6. When the connectors of all the cables have been removed from the redundant power supply, remove the redundant power supply with its housing from the device.
Installation
Install the device in reverse order. Secure the cables using the cable clips available in the device as well as with new cable ties.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
111
Device maintenance and repair
7.5 Removing and installing hardware
7.5.6 Removing and installing the piggyback and bus board
This chapter describes the removal and installation of bus boards and piggybacks.
Information about the various variants of bus boards and piggybacks is available in chapter
"Bus board models (Page 170)".
Requirement
● The device is open, see the section "Open the device. (Page 70)".
● The bus frame has been removed, see chapter "Removing and installing bus frame
Removing the piggyback
1. Remove the marked screws with which the piggyback is fastened to the middle rail of the bus frame.
2. On the other side of the middle rail of the bus frame remove the angle connector of the piggyback from the bus board as shown in the following figure.
3. Guide the angle connector of the piggyback through the middle rail of the bus frame and remove the piggyback as shown in the following figure.
112
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Device maintenance and repair
7.5 Removing and installing hardware
Removing the bus board
1. Remove all 5 expanding rivets with which the bus board is fastened to the middle rack of the bus frame.
2. Use a screwdriver to press on the end of the expansion rivet until the expansion rivet can be freely moved.
Procedure
Installation
Install the device in reverse order. Use only new expansion rivets to mount a bus board.
7.5.7
Requirement
Removing the OP
● The device is open, see the section "Open the device. (Page 70)".
● The bus frame has been removed, see chapter "Removing and installing bus frame
● 1 operator panel
● 1 crosstip screwdriver
Procedure
Read the section "ESD guideline (Page 135)".
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
113
Device maintenance and repair
7.5 Removing and installing hardware
Removal
1. Remove the marked screws.
2. Fold the crossbar in the direction of the arrow.
3. Remove the USB connector.
4. Remove the marked screws and then the operator panel.
114
5. Loosen the white flat cable at the plug connector lock
②
by sliding the
①
to the left.
Installation
Install the device in reverse order.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
7.5.8
Device maintenance and repair
7.5 Removing and installing hardware
Removing and installing the processor cooler
The processor cooler used in the device forms a unit together with heat pipes and further heat exchangers.
①
Heat exchangers
②
Heat pipe
③
Heat sink
Requirement
● The device is open, see the section "Open the device. (Page 70)".
● The bus frame has been removed, see chapter "Removing and installing bus frame
● 1 processor cooler
Information about original spare parts for SIMATIC IPCs is available on the Internet at:
SIMATIC IPC after-sales information system ( http://www.siemens.com/asis )
● 1 T10 screwdriver
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
115
Device maintenance and repair
7.5 Removing and installing hardware
Procedure
Removal
1. Remove the highlighted six screws.
2. Remove the processor cooler from of the device.
Installation
Make sure that the heat sink pad on the heat sink exists and is intact. The same applies for the rubber feet marked in the figure.
To install the fan, follow the steps for removing it in reverse order. Tighten the screws at the heat sink gradually crosswise. Avoid uneven tightening as this may result in a tensioning of the heat sink.
Further procedure
1. Install the bus frame.
2. Close the device.
116
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Device maintenance and repair
7.5 Removing and installing hardware
7.5.9
Requirement
Removing the motherboard
● The device is open, see the section "Open the device. (Page 70)".
● The bus frame has been removed, see chapter "Removing and installing bus frame
● 1 motherboard
Information about original spare parts for SIMATIC IPCs is available on the Internet at:
SIMATIC IPC after-sales information system ( http://www.siemens.com/asis ).
The motherboard is supplied as a spare part with soldered-on processor - but without processor heat sink, memory modules and bus board.
● 1 hex key 4.5 mm
● T10 screwdriver
Procedure
Observe the EGB guidelines.
Removal
1. Disconnect all cables from the motherboard, noting down their positions while doing so.
2. Remove the 9 screws from the positions indicated in the following figure.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
117
Device maintenance and repair
7.5 Removing and installing hardware
3. Use a hex key to remove the hex bolts marked in the following figure.. The following figure shows the PROFIBUS device with MPI/DP interface. Only the two middle screws of the COM1 port have to be loosened at the other device variants.
4. Slide the motherboard carefully inwards until the D-sub sockets have loosened from the rear panel.
NOTICE
Damage to the motherboard
Components can be damaged when removing the motherboard.
•
Proceed slowly and carefully when moving and removing the motherboard.
• Ensure that the bottom of the motherboard does not contact projecting housing parts when sliding it.
5. Lift the motherboard carefully out of the housing.
Installation
To install the fan, follow the steps for removing it in reverse order.
Further procedure
1. Install the bus frame.
2. Close the device.
See also
Connection information (Page 38)
118
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Device maintenance and repair
7.5 Removing and installing hardware
7.5.10
Requirement
Replacing the processor
● The device is open, see the section "Open the device. (Page 70)".
● The bus frame has been removed, see chapter "Removing and installing bus frame
● 1 approved processor
Only an approved processor is permitted to be installed on the motherboard of the device. If the processor type is changed, the BIOS must be updated so that the suitable microcode is loaded. Information about original spare parts for SIMATIC IPCs is available on the Internet at:
– SIMATIC IPC after-sales information system ( http://www.siemens.com/asis )
– Contacts ( http://www.siemens.com/automation/partner )
Procedure
Observe the EGB guidelines.
Removal
1. Unlock the lever
①
and swivel it to the rear.
The holding frame
②
moves back and exposes the screw
③
.
2. Fold up the holding frame
②
.
3. Remove the processor.
Do not touch the contacts of the processor in the process.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
119
Device maintenance and repair
7.5 Removing and installing hardware
NOTICE
Damage to the motherboard
Do not touch the contacts of the processor base when the processor is removed. Ensure that the base id free of soiling or foreign matter.
Installation
1. Place the processor on the base.
Make sure when you insert the processor that the position identifier (metallic triangle) on the processor is in the right place.
2. Swivel the lever
①
toward the processor.
The holding frame moves as well and must then grip the screw
③
.
3. Press the lever
①
all the way down and lock it.
NOTICE
Damage to the processor
If the locking mechanism jams, it can be damaged when it is pressed down completely.
The processor is then not held correctly in place by the holding frame. The result may be malfunctions.
Therefore use only a low level of force and if a fault occurs, swivel the lever back.
Eliminate the cause of the fault.
120
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Device maintenance and repair
7.6 Installing the software
Further procedure
1. Install the bus frame.
2. Close the device.
3. When a processor is replaced, perform a BIOS update.
The microcode matching the processor is loaded in the process. The procedure is described "Technical manual of the motherboard" document on the "Documentation and
Drivers" DVD.
NOTICE
Damage to the processor
If the installed processor is operated with a higher clock frequency than permitted, it can be destroyed or cause loss of data.
Operate the processor only at a clock frequency that is equal to or less than the permitted clock frequency.
7.6 Installing the software
7.6.1 Sources for installation of the operating system
If the operating system is faulty, you can reinstall it with one of these DVDs:
● With the recovery DVD and "Documentation and Drivers" DVD
The recovery DVD is included in the scope of delivery when you have ordered a device with operating system. The recovery DVD includes:
– The installation program for installing the operating system with the supported languages
– The tools for setting up the drives
The basic language of the installed operating system is English. If additional languages are required, install these from the recovery DVD.
The "Documentation and Drivers" DVD contains the documentation and the hardware drivers.
● From the Restore DVD
The Restore DVD is included in the scope of delivery when you have ordered a device with operating system. The DVD contains an image file with the following software:
– Operating system with installed hardware drivers
– Monitoring software, e.g., DiagBase.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
121
Device maintenance and repair
7.6 Installing the software
7.6.2
Windows
Updating the operating system
The latest updates for the Windows operating system are available on the Internet at
Microsoft ( http://www.microsoft.com
) and on the device in the Start menu "Start > All
Programs > Windows Update > Check for updates".
Note
Before you install new drivers or operating system updates for Windows MUI versions, configure the regional menu and dialog settings and the default English (US) language.
other operating systems
Contact the corresponding manufacturer.
7.6.3
Requirement
Installing drivers and software
You need the "Documentation and Drivers" DVD included in the scope of delivery to install
Windows drivers.
Procedure
Installing drivers
1. If your device has no DVD drive, connect an external USB DVD drive to a USB port.
2. Insert the supplied "Documentation and Drivers" DVD.
3. Start the "Start" program.
4. Accept the licensing conditions.
5. Select "Drivers" from the index.
6. Select the device and operating system.
7. Select the required driver.
8. Open the folder with the driver data. Click on the link next to "driver path".
9. Start the setup program in this folder.
Note
The driver for the chepset must be installed first with a new Windows installation. Then you can install the drivers of all other devices.
122
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Device maintenance and repair
7.6 Installing the software
Installing the software
● You can find information about installing SIMATIC software packages in the corresponding documentation.
● You can obtain information about driver updates and installing application programs from the respective manufacturers.
7.6.4 Installing Windows
Note
Specific information on using the Windows operating systems is available on the Internet:
• Microsoft Technet Windows
•
Microsoft Technet Windows Server
Requirement
You need the Recovery DVD for the operating system you want to install. The recovery DVD is included in the scope of delivery when you have configured a device with operating system.
If you use storage controllers that are unknown to the operating system, for example a RAID or AHCI controller, copy the respective controller driver to a USB stick and keep this USB stick to hand. The controller driver is required during installation.
Procedure
1. If your device has no DVD drive, connect an external USB DVD drive to a USB port.
2. Insert the Recovery DVD into the DVD drive.
3. Reboot the device.
4. Press the <Esc> key when the device boots and keep it pressed.
The BIOS selection menu is displayed when initialization is completed.
5. Click the "Boot Manager" button.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
123
Device maintenance and repair
7.6 Installing the software
6. Select the optical drive using the cursor keys.
For your system to boot in "UEFI" mode after installation, you must also boot the recovery
DVD using UEFI. You data storage medium will be set up with GPT partition management during installation of Windows.
To boot the recovery DVD in "UEFI" mode, in the "Boot" menu in BIOS setup select the item for which the optical drive is identified with "UEFI" in front of the name. Example:
UEFI: MATSHITADVD-RAM UJ8E0
For your system to boot in "Legacy" mode after installation, you must also boot the recovery DVD using Legacy. You data storage medium will be set up with MBR partition management during installation of Windows.
To boot the recovery DVD in "Legacy" mode, in the "Boot" menu in BIOS setup select the item for which the optical drive is identified with "P" in front of the SATA port number.
Example:
P5: MATSHITADVD-RAM UJ8E0
7. Confirm the selection by pressing ENTER.
8. Immediately press any key when you see the following prompt to install the operating system from the Recovery DVD.
Press any key to boot from CD or DVD ..
After a few seconds, you will see the "Install Windows" installation program.
9. Now follow the instructions in the installation program.
You can find additional information on this in the next section.
"Install Windows" installation program
The language of the installation program and the operating system is preset to English. You can change the language of the operating system after the installation. Information on this topic is available in the section "Setting up the language selection using the Multilanguage
User Interface (MUI)".
Setting up partitions and integrating storage controllers unknown to the operating system
You can set up partitions during the installation process and integrate storage controllers that are unknown to the operating system. To do so, select "Custom (advanced)" when prompted for the installation type in the "Install Windows" installation program.
124
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
The following dialog boxes are available:
Device maintenance and repair
7.6 Installing the software
Refresh
Load Driver
Drive options
(advanced)
Updating
Integration of controller drivers unknown to the operating system and required for installation. Please read the information in the section "Information for systems with RAID or AHCI controller".
For display of additional functions that you can use to set up the data medium, see figure "Windows installation window "Drive options (advanced)"".
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
125
Device maintenance and repair
7.6 Installing the software
Refresh
Load Driver
Delete
Extend
Format
New
Updating
Integration of controller drivers unknown to the operating system and required for installation. Please read the information in the section "Information for systems with RAID or AHCI controller".
Deleting a partition
Changing the partition size
Formatting a partition
Creating new partitions
Identification for error messages, for example, if the data medium was not formatted in the required "NTFS" format.
Note
If you want to install the operating system on a data medium connected to a storage controller unknown to the operating system, you have to integrate the driver of the storage controller. Integrate this driver before you partition the data medium and before you install the operating system. For more information on integrating the storage controller, refer to the section "Information for systems with RAID or AHCI controller".
126
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Device maintenance and repair
7.6 Installing the software
1. Make sure that the partition on which you want to install the operating system is large enough and is set up with a NTFS file system.
The recommended minimum size of this partition varies, depending on the operating system, how much RAM you have available and how much additional software you want to use. Information on how the data medium is partitioned in its factory state is available in the tables below.
2. Select the partition on which you want to install the operating system.
3. Click "Next".
Installation is started. The Windows operating system is installed on the data medium.
Partitions in delivery state for Windows 7 and Windows Server 2008 R2
The following information applies to data storage media ≥ 100 GB.
Partition Name
First BOOT
Second
Third
SYSTEM
DATA
Size
100 MB
100 GB
Remainder
File system
Automatically set up by installation program
NTFS not compressed
NTFS not compressed
Windows Server 2012 R2 partitions in the factory state
The following information applies to data storage media ≥ 100 GB.
Partition Name
First WinRE
Second Boot
Third
Fourth
Fifth
MSR
System
Data
Size
300 MB
260 MB
128 MB
100 GB
Remainder
File system
NTFS
FAT32, automatically set up by installation program
FAT32, automatically set up by installation program
NTFS not compressed
NTFS not compressed
Information for systems with RAID or AHCI controller
Data carrier controllers unknown to the operating system must be made known to the operating system prior to installation in the "Install Windows" installation program.
Requirement
You have copied the relevant controller driver to a USB stick.
Procedure
1. Connect the USB stick with the controller driver to the device.
2. Start the "Install Windows" installation program as described above.
3. Select "Load Drivers" in the Windows installation window.
4. Select the respective driver on the USB stick.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
127
Device maintenance and repair
7.6 Installing the software
7.6.5 Setting up the language selection using the Multilanguage User Interface (MUI)
You can set the display of menus, dialogs or other information, such as date and time, to a different language. For this purpose, you can either select one of the preinstalled languages or install a new language package.
The following command sequences are described in English. Depending on the default setting, they can be displayed in another language.
Procedure
Changing the settings for language, region and formats of a registered user account
Windows 7 and Windows Server 2008 R2:
1. Choose:
"Start > Control Panel > Clock, Language, and Region > Regional and Language
Options"
2. You can make the desired changes in the "Formats" and "Location und Keyboards and
Languages" tabs.
Windows Server 2012 R2:
1. Choose:
"Start > Control Panel > Clock, Language, and Region > Region"
2. You can make the desired changes in the "Formats" and "Location" tabs.
Changing the settings for language, region and formats of the system account and the standard user account
You can change the settings for language, region and formats of the system account (for example, the language in the user login dialog) and the settings of the standard user account
(standard setting for new users). The settings of the registered user are copied to the system account and the standard user account for this purpose.
Windows 7 and Windows Server 2008 R2:
1. Choose:
"Start > Control Panel > Clock, Language, and Region > Regional and Language
Options"
2. You can make the required changes in the "Administrative" tab. You copy the settings by clicking the respective button.
Windows Server 2012 R2:
1. Choose:
"Start > Control Panel > Clock, Language, and Region > Region"
2. You can make the required changes in the "Administrative" tab. You copy the settings by clicking the respective button.
128
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Device maintenance and repair
7.6 Installing the software
Installing language package
The available language packages are described in the chapter "Design of the device". Some language packages are available on the Recovery DVD in the "Languagepacks" folder.
Windows 7 and Windows Server 2008 R2:
1. Choose:
"Start > Control Panel > Clock, Language, and Region > Regional and Language
Options"
2. Select the "Keyboards and Languages" tab.
3. Click the "Install/uninstall languages" button and make the required changes.
Windows Server 2012 R2:
1. Right-click the start menu in the task bar and select "Command Promt (Admin)".
2. Enter the following command in the command line:
Dism /online /Add-Package /PackagePath:#Path to the language pack#
For "
#Path to language pack#
", enter the path to the language pack you want to install.
Example:
Dism /online /Add-Package /PackagePath:E:\Languagepacks\ja-jp\lp.cab
7.6.6 Restoring the delivery state
You can restore the original software using the Restore DVD. The DVD contains the necessary images and tools for transferring the software to the hard disk drive or SSD of your device.
The following options are available for restoring the delivery state:
● Restore the entire hard disk/SSD with drives C and D
● Restore drive C
This means data stored on drive D are retained.
Back-up authorization or license key
● Check whether you can back-up your authorization or license key from the drive and perform this procedure if possible.
● If backup is not possible, please contact Customer Support. There you can obtain information necessary for corresponding software authorization.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
129
Device maintenance and repair
7.6 Installing the software
NOTICE
Risk of data loss
If "Restore system partition only" is set all data on drive C: (system partition) will be deleted. All data, user settings and all authorizations or license keys on drive C: are lost!
All data on drive C: will be completely deleted, reformatted and overwritten with the original factory software.
If "Restore entire drive" is set ALL data, user settings, authorizations or license keys will be lost on the entire drive.
Procedure
1. If your device has no DVD drive, connect an external USB DVD drive to a USB port.
2. Insert the Restore DVD into the DVD drive.
3. Reboot the device.
4. Press the <Esc> key when the device boots and keep it pressed.
The BIOS selection menu is displayed when initialization is completed.
5. Click the "Boot Manager" button.
6. In the boot menu, select the optical drive using the cursor keys.
To restore a system which boots in "UEFI" mode, you must also boot the restore DVD using UEFI.
To boot the restore DVD in "UEFI" mode, in the "Boot" menu in BIOS setup select the item for which the optical drive is identified with "UEFI" in front of the name. Example:
UEFI: MATSHITADVD-RAM UJ8E0
To restore a system which boots in "Legacy" mode, you must also boot the restore DVD using Legacy.
To boot the recovery DVD in "Legacy" mode, in the "Boot" menu in BIOS setup select the item for which the optical drive is identified with "P" in front of the SATA port number.
Example:
P5: MATSHITADVD-RAM UJ8E0
Note
Windows Server 2012 R2 boots in "UEFI" mode in the factory state.
Windows 7 and Windows Server 2008 R2 boot in "Legacy" mode in the factory state.
7. Follow the instructions on the screen.
Note
All existing data, programs, user settings, authorizations and license keys on the drives are deleted.
130
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
7.6.7
Device maintenance and repair
7.6 Installing the software
Installing onboard RAID controller software
You install the software of the onboard RAID controller with its driver.
7.6.8 Installing Hardware RAID controller software
Note
Observe the "General information on commissioning (Page 49)" in section "Commissioning
the device". Additional information is available in section "Installing drivers and software
7.6.9 Backing up data and changing partitions at a later time
We recommend the software tool SIMATIC IPC Image & Partition Creator to back up data under Windows operating systems. This tool provides convenient and efficient functions for backing up and restoring the full content of memory cards, hard disks and individual partitions (images).
SIMATIC IPC Image & Partition Creator supports the burning of DVD media. You can order the tool using the Siemens online ordering system Industry Mall
( https://mall.industry.siemens.com
). For more information on SIMATIC IPC Image & Partition
Creator, refer to the corresponding product documentation.
Note
SIMATIC IPC Image & Partition Creator supports the device hardware as of version 3.3.3.
Data storage media set up with GPT partition management are supported as of version 3.4.
Older versions do not support the device hardware.
For devices with a Hardware RAID adapter card, the device driver must be downloaded subsequently. A function is available for this in the SIMATIC IPC Image & Partition Creator.
For information on SIMATIC IPC Image & Partition Creator, refer to the corresponding product documentation.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
131
Device maintenance and repair
7.6 Installing the software
7.6.10 CP 1616 onboard
NDIS device driver
Read the information in the Device_driver_CP16xx.pdf document on the supplied
"Documentation and Drivers" DVD.
PROFINET IO
Read the information regarding the SIMATIC devices and SIMATIC NET documentation listed in the "Connecting the device" section.
132
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical specifications
8
8.1 Certificates and approvals
ISO 9001 certificate
The Siemens quality management system for our entire product creation process
(development, production and sales) meets the requirements of ISO 9001:2008.
This has been certified by DQS (the German society for the certification of quality management systems).
Certificate no.: 001323 QM08
Software license agreements
If the device is supplied with preinstalled software, you must observe the corresponding license agreements.
UL approval
The following approvals are available for the device:
● Underwriters Laboratories to Standard-UL 60950-1, File no. E11 5352
● Canadian National Standard CAN/CSA-C22.2 No. 60950-1-07 (I.T.E)
FCC and Canada
USA
Federal
Communications
Commission
Radio Frequency
Interference
Statement
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Shielded Cables Shielded cables must be used with this equipment to maintain compliance with
FCC regulations.
Modifications
Conditions of
Operations
Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
CANADA
Canadian Notice This Class B digital apparatus complies with Canadian ICES-003.
Avis Canadien Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
133
Technical specifications
8.2 Directives and declarations
AUSTRALIA / NEW ZEALAND
This product meets the requirements of the standard EN 61000-6-3:2007 Generic standards
- Emission standard for residential, commercial and light-industrial environments.
This product meets the requirements of the standard EN 61000-6-3:2007 Generic standards
- Emission standard for residential, commercial and light-industrial environments.
Identification for Eurasion Customs Union
● EAC (Eurasian Conformity)
● Customs union of Russia, Belarus and Kazakhstan
● Declaration of conformity according to Technical Regulations of the Customs Union (TR
CU)
KOREA
This product meets the requirements of Korean certification.
This product satisfies the requirement of the Korean Certification (KC Mark).
이 기기는 업무용(A급) 전자파 적합기기로서 판매자 또는 사용자는 이 점을 주의하시기
바라며 가정 외의 지역에서 사용하는 것을 목적으로 합니다.
8.2 Directives and declarations
The device meets the guidelines listed in the following sections.
EC Declaration of Conformity
The associated declaration of conformity is available on the Internet at the following address:
Rack PC certificates
( http://support.automation.siemens.com/WW/view/en/10805674/134200 ).
Electromagnetic compatibility
This product meets the requirements of EC Directive 2004/108/EC "Electromagnetic
Compatibility".
The device is designed for the following areas of application corresponding to the CE marking:
Scope of application
Industrial area
Residential and commercial areas and small businesses
Requirements for
Interference emission
EN 61000-6-4 : 2007 +A1:2011
EN 61000-6-3 : 2007 +A1:2011
Immunity to interference
EN 61000-6-2 : 2005
EN 61000-6-1 : 2007
The devices comply with the standards EN 61000-3-2:2006 +A1:2009 +A2:2009 (harmonic currents) and EN 61000-3-3:2008 (voltage fluctuations and flicker).
Low-voltage directive
The device with AC power supply complies with the requirements of the EC Directive
2006/95/EC "Low Voltage Directive". Compliance with this standard has been verified according to EN 60950-1:2006 + A11:2009 +A1:2010 +A12:2011.
134
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
8.2.1 ESD guideline
What does ESD mean?
An electronic module is equipped with highly integrated components. Due to their design, electronic components are highly sensitive to overvoltage and thus to the discharge of static electricity. Such electronic components or modules are labeled as electrostatic sensitive devices.
The following abbreviations are commonly used for electrostatic sensitive devices:
● ESD – Electrostatic sensitive device
● ESD – Electrostatic Sensitive Device as a common international designation
Electrostatic sensitive devices can be labeled with an appropriate symbol.
NOTICE
Damage to ESD from touch
Electrostatic sensitive devices, ESD, can be destroyed by voltages which are far below the human perception limit. If you touch a component or electrical connections of a module without discharging any electrostatic energy, these voltages may arise.
The damage to a module by an overvoltage can often not be immediately detected and only becomes evident after an extended period of operation. The consequences are incalculable and range from unforeseeable malfunctions to a total failure of the machine or system.
Avoid touching components directly. Make sure that persons, the workstation and the packaging are properly grounded.
Charge
Technical specifications
8.2 Directives and declarations
Every person without a conductive connection to the electrical potential of his/her surroundings can be electrostatically charged.
The material with which this person comes into contact is of particular significance. The figure shows the maximum electrostatic voltages with which a person is charged, depending on humidity and material. These values conform to the specifications of IEC 61000-4-2.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
135
Technical specifications
8.2 Directives and declarations
①
Synthetic materials
②
Wool
③
Antistatic materials such as wood or concrete
NOTICE
Grounding measures
There is no equipotential bonding without grounding. An electrostatic charge is not discharged and may damage the ESD.
Protect yourself against discharge of static electricity. When working with electrostatic sensitive devices, make sure that the person and the workplace are properly grounded.
Protective measures against discharge of static electricity
● Disconnect the power supply before you install or remove modules which are sensitive to
ESD.
● Pay attention to good grounding:
– When handling electrostatical sensitive devices, make sure that persons, the workstation and devices, tools and packaging used are properly grounded. This way you avoid static discharge.
● Avoid direct contact:
– As a general rule, do not touch electrostatic sensitive devices, except in the case of unavoidable maintenance work.
– Hold the modules at their edge so that you do not touch the connector pins or conductor paths. This way, the discharge energy does not reach and damage the sensitive components.
– Discharge your body electrostatically before you take a measurement at a module. Do so by touching grounded metallic parts. Always use grounded measuring instruments.
136
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
8.3
8.3.1
Dimension drawings
Dimensional drawing of the device
Technical specifications
8.3 Dimension drawings
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
137
Technical specifications
8.3 Dimension drawings
8.3.2 Dimension drawing of the telescopic rails
The following dimension drawing shows the dimensions of the telescopic rails from the Rittal company.
8.3.3 Dimension drawing of the expansion cards
The following dimension drawing shows the main dimensions of the PCI and the PCI
Express expansion card without slot bracket and retainer. a
PCI
106.7 mm
PCIe
111.2 mm
Note
Mounting of a retainer is required to ensure correct location of long expansion cards in the provided guide rails.
138
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
8.4 Technical specifications
8.4.1 General specifications
General specifications
Order number
Dimensions
Weight
Supply voltage (V
N
)
Input current AC
Line voltage frequency
Transient voltage interruption
Power consumption
Power loss / heat emission
Current delivery (DC)
Noise emission
Degree of protection
Dust protection
Safety
Protection class
Safety regulations
Technical specifications
8.4 Technical specifications
6AG4112-2...(for details, refer to the ordering documentation)
430 × 88.1 × 444.6 (W × H × D in mm). Detailed dimensional
specifications can be found in section Dimensional drawing of the device (Page 137).
Min. 10 kg, max. 14 kg
100 to 240 VAC (–15%, 10%), varying voltage; with transient power failure backup in accordance with NAMUR
Continuous current up to 6 A (up to 30 A for 5 ms at startup)
50 to 60 Hz (min. 47 Hz to max. 63 Hz, sinusoidal)
Min. 20 ms at 93 V
(max. 10 events per hour; recovery time at least 1 s)
AC power supply: Max. 240 W at 80% efficiency
Redundant AC power supply: Max. 240 W at 80% efficiency
AC power supply: 240 W = 240 J/s = 0.23 BTU/s
Redundant AC power supply: 240 W = 240 J/s = 0.23 BTU/s
+5 V/30 A + 3.3 V/28 A, max. aggregate power 160 W
+12 V/15 A -12 V/0.5 A -5 V/0.5 A +5 Vaux/2 A
Aggregate power of all voltages max. 190 W
< 45 dB(A) at 25 °C according to DIN EN ISO 7779
ODDs not in operation
IP41 at the front and IP20 at the rear according to IEC 60529
With closed front panel
Filter class G2 EN 779, 99% of particles > 0.5 mm are filtered
Protection class I according to IEC 61140
•
IEC 60950-1
• EN 60950-1
•
UL 60950-1
• CSA C22.2 No 60950-1-07
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
139
Technical specifications
8.4 Technical specifications
Electromagnetic compatibility (EMC)
Radiated interference
Noise immunity:
Conducted disturbance variables on supply lines
Noise immunity on signal lines
Immunity to discharge of static electricity
Immunity to
RF interference
Magnetic field
EN 61000-6-3, FCC Class A
EN 61000-6-4;
CISPR 22,EN 55022 class B
EN 61000-3-2 class D, EN 61000-3-3
± 2 kV, according to IEC 61000-4-4, burst
± 1 kV, according to IEC 61000-4-5, surge sym.
± 2 kV, according to IEC 61000-4-5, surge asym.
± 1 kV, according to IEC 61000-4-4; Burst; Length < 30 m
± 2 kV, according to IEC 61000-4-4; Burst; Length > 30 m
± 2 kV, according to IEC 61000-4-5; Length > 30 m
±6 kV contact discharge, according to IEC 61000-4-2
± 8 kV air discharge, according to IEC 61000-4-2
• 10 V/m, 80...1000 MHz and 1.4...2 GHz,
80% AM 1 kHz, according to IEC 61000-4-3
• 3 V/m 2...2.7 GHz, 80% AM 1kHz, according to IEC 61000-4-3
• 10 V, 10 KHz...80 MHz, 80% AM 1 kHz, according to IEC 61000-4-6
100 A/m, 50 Hz/60 Hz, nach IEC 61000-4-8
Climatic ambient conditions
Temperature
During operation
Gradient
Tested in accordance with IEC 60068-2-2, IEC 60068-2-1, IEC 60068-2-14
0 °C … +35 °C, without restriction under the provided technical specifications
0 °C … +40 °C, ODD operation, no Hardware RAID, total power loss of expansion cards less than 55 W
0 °C … +45 °C, no ODD operation, no Hardware RAID, total power loss of expansion cards less than 55 W
0 °C … +50 °C * No ODD operation, no HDD operation in the removable drive bay, no Hardware RAID
Max. 10 °C/h, no condensation
* Power dissipation of the expansion cards in total less than 30 W
–20 °C … +60 °C max. 20° C/h, no condensation
Tested in accordance with IEC 60068-2-78, IEC 60068-2-30
Storage/transport
Gradient
Relative humidity
In operation
Gradient
Storage/transport
Gradient
5% to 80% at 25 °C (no condensation)
Max. 10°C/h, no condensation
5% to 95% at 25 °C (no condensation)
Max. 20 °C/h, no condensation
Atmospheric pressure
During operation 1080 to 795 hPa, corresponds to an elevation of -1000 to 2000 m
Stoage/transport 1080 to 660 hPa, corresponds to an elevation of -1000 to 3500 m
140
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical specifications
8.4 Technical specifications
Mechanical ambient conditions
Vibration
Operation
1
Storage/transport
Resistance to shock
Operation
1
Storage/transport
Special features
Tested in accordance with IEC 60068-2-6, 10 cycles
10 Hz to 58 Hz: 0.0375 mm, 58 Hz to 500 Hz: 4.9 m/s
2
5 Hz to 9 Hz: 3.5 mm, 9 Hz to 500 Hz: 9.8 m/s
2
Tested in accordance with IEC 60068-2-27, IEC 60068-2-29
Half-sine: 50 m/s
2
Half-sine: 250 m/s
, 30 ms, 100 shocks per axis
2 , 6 ms, 1000 shocks per axis
Quality assurance In accordance with ISO 9001
1
Mechanical interference must be safely excluded during the burning operation.
Motherboard
Chipset Intel® DH82C226 Express Chipset (Platform Controller Hub)
Integrated RAID (on-board) Intel® 8 Series SATA RAID Controller
Processor
•
Intel® Xeon™ E3-1268L v3 2.3 (3.3) GHz, 4 cores, GT2, 8 MB
SLC, HT
• Intel® Core™ i5-4570TE 2.7 (3.3) GHz, 2 cores, GT2, 4 MB SLC,
AMT
•
Intel® Core™ i3-4330TE 2.4 GHz, 2 cores, GT2, 3 MB SLC, AMT
RAM
Memory expansion
Expansion slots
4 DIMM base maximum 32 GB DDR3 with 1600 MT/s SDRAM
Modules with and without ECC can be operated.
2 GB to 32 GB DDR3, max. 3.5 GB can be used for 32-bit operating system and applications.
Modules with and without ECC can be ordered (configuration see order documents). Module size maximum 8 GB, module organization
2 Gbits / 4 Gbits based x8 organized
Max. 4 expansion cards simultaneously, grouped as follows:
•
2 × PCI, 2 × PCIe mech. x16 (8 lanes) or
Maximum permissible current consumption per PCI slot
Maximum permissible current consumption per PCIe slot
•
4 × PCIe mech. x16 (4 lanes / 8 lanes depending on slot)
•
2 × PCIe mech. x16 (4 lanes)
All expansion cards up to 312 mm length can be inserted.
5 V/ 5 A or 3.3 V/ 7 A, 12 V/ 0.5 A, -12 V/ 0.05, 3.3 Vaux/ 0.4 A
3.3 V / 3 A; 12 V / 2.1 A; 3.3 Vaux / 0.4 A
Max. permissible power loss per PCI slot
Power consumption over all slots, maximum permissible
Maximum bandwidth of PCI slots
Maximum bandwidth of the
PCIe
1
slots
Accumulated power loss (all voltages) may not exceed 25 W.
Total power consumption (all slots) may not exceed 75 W. Aggregate
3.3 Vaux current may not exceed 0.8 A.
133 MB/s bandwidth
Gen 2, 5 GT/s (500 MB/s) bandwidth per lane
Gen 3, 8 GT/s (985 MB/s) bandwidth per lane
1
The total bandwidth results from the number of available lanes per slot.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
141
Technical specifications
8.4 Technical specifications
Drives (for configuration details, refer to the order documentation)
Hard disks 3.5" SATA 6 Gbps, size:
Solid State Drive
DVD burner
•
500 GB or 2 × 500 GB
• 1000 GB or 2 × 1000 GB
3.5" SAS 6 Gbps, size: 1000 GB
NCQ (Native Command Queuing) is supported.
2.5" SATA 240 GB (MLC)
Slimline SATA
Read:
• DVD ROM: Single layer 8x, dual layer 6x
•
DVD-R/+R: Single Layer 8×, Dual Layer 6×,
DVD-RW/+RW 8×,
• DVD-RAM; 5× CD-R 24×, CD-RW 24×
Write:
•
DVD+R 8×, DVD+RW 8×, DVD-R 8×, DVD-RW 6×
• DVD+R9 (DL) 6×, DVD-R DL 2×
•
CD-R 24×, CD-RW 24×
Hardware RAID controller
SAS Hardware RAID controller (optional)
Parameter
• SAS RAID module PCIe x8, RAID 1, 5
•
Type: Adaptec 8405 (independent processor, 1024 MB DDR3 cache)
•
1 × Mini SAS HD adapter (SFF-8643 for 4 drives)
•
Maximum theoretical controller data rate 12 Gb/s per port
•
Maintenance-free buffer unit for onboard cache memory
Graphics
Graphics controller
Graphics memory
Resolutions/frequencies/colors
Intel® HD Graphics Controller, P4600/P4700 GT1/GT2, 2-D and 3-D engine integrated in processor
Dynamic Video Memory Technology,uses 32 MB to 1.7 GB RAM in main memory
• CRT (via DVI-I VGA adapter): Up to 2560 x 1600 at 120 Hz / 32-bit color depth
•
LCD via DVI-D: Up to 2048 x 1152 at 60 Hz / 32-bit color depth
• LCD via DisplayPort: Up to 4096 x 1152 at 24 Hz / 32-bit color depth
Graphics card (optional)
•
PCIe x16 graphics card, dual head (2 × DP, 2 × VGA or 2 × DVI-D)
•
Type: NVIDIA NVS-300, 512 MB graphics memory
•
Maximum resolution:
– DisplayPort 2560 × 1600 at 60 Hz, 32 bit color depth
– DVI 1920 × 1200 at 60 Hz, 32 bit color depth
– VGA 2048 x 1536 at 60 Hz, 32-bit color depth
142
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Interfaces
Technical specifications
8.4 Technical specifications
COM1; COM2 (optional)
LPT (optional)
VGA (optional) (DVI-I)
1 × DVI-I
2 × DisplayPort
2 × DisplayPort / DVI-D/VGA with
Dual Head graphics card (optional)
Keyboard
Mouse
USB Rear of the device
Serial interface 1 (V.24), 9-pin D-sub connector
Parallel interface (Standard, EPP and ECP mode), connection for printer with parallel interface
Double-row module connector (per ribbon cable at 25-pin sub
D connector)
Connection of an analog monitor via DVI-I / VGA adapter
For connecting a digital monitor
For connecting a digital monitor
For connecting two digital or analog monitors DisplayPort,
DVI-D or VGA via DMS59 cable adapter
PS/2 keyboard connection
PS/2 mouse connection
2 × USB 3.0 high current
2 × USB 2.0 high current
Front panel
Internal
PROFIBUS (optional)
1 × USB 3.0 high current
1 × USB 2.0 high current
1 × USB 3.0 device high current
9-pin D-sub socket, CP5622-compatible, 9.6 Kbps to 12
Mbps, programmable with software:
DP master: DP-V0, DP-V1 with SOFTNET-DP
DP slave: DP-V0, DP-V1 with SOFTNET-DP slave
RS 485 electrically isolated (SELV circuit)*
PROFINET
Ethernet
2
2
3 × RJ45 interface, CP 1616 compatible onboard interface based on ERTEC 400, 10/100 Mbps electrically isolated *
2 × Ethernet interface (RJ-45), Wake on LAN, Remote Boot and teaming are supported.
10/100/1000 Mbps, electrically isolated *
Ethernet 1: WGI217LM, AMT-capable
1
, supports jumbo frames up to 9014 bytes
Ethernet 2: Intel WGI210IT, supports jumbo frames up to
9014 bytes
IDT 92HD81HD
2 × 0.5 W / 8 Ohm
Audio
- Microphone
- Line out / Headset
*
1
Electrical isolation within the safety extra-low voltage circuit (SELV)
AMT and teaming cannot be used simultaneously on the Ethernet interface
2
For unique assignment, the LAN interfaces are numbered on the enclosure. The numbering by the operating system may deviate from this.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
143
Technical specifications
8.4 Technical specifications
Status displays (LEDs)
Labeling on the front panel LED color
POWER
HDD
ETHERNET 1 1
ETHERNET 2
1
PROFIBUS/MPI
SF PROFINET
2
GREEN
YELLOW
GREEN
GREEN
GREEN
GREEN
RED
Meaning
Device active standby
HDD active
Active
Active
Active
No cable connected or fault
WATCHDOG
RED flashing
GREEN
RED
RED
Fault or node flash test function
Active
Alarm
Temperature alarm TEMP
FAN
HDD 0
HDD 1
RED
RED or both RED, or
RED flashing
3
Fan alarm
Hard disk alarm in conjunction with SIMATIC monitoring software
1
For unique labeling, the LAN interfaces are numbered on the enclosure. The numbering by the operating system may deviate from this.
2
Interfaces supplied as optional.
3
See chapter "Status displays"
Note
Hardware RAID adapter card
The Hardware RAID adapter card may only be installed in slot 1.
144
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical specifications
8.4 Technical specifications
8.4.2
Base system
Current and power requirements
Component Voltage
Motherboard core i processor with cooling
Front fan
Fan inside
Motherboard Xeon processor with cooling 1
Hard disk drive
1
SATA and SAS
(typical values)
SSD SATA (typical)
SAS Hardware Controller
Base system (dual core)
Slimline drive
1
1
Single currents ATX, max. permitted
Single currents ATX redundant, max. permissible
Total power consumption, permissible
Efficiency of the single and redundant power supply
1
+3.3 V +5 V
1.2 A
1.2 A
0.4 A
1.2 A
0.8 A
20 A
20 A
185 W
2
2
2.8 A
2.8 A
0.5 A
3.3 A
25 A
20 A
2
2
+12 V
0.35 A
1.0 A
0.3 A
0.95 A
0.7 A
0.25 A
1.2 A
1.65 A
11 A
18 A
+12 V2
5.35 A
5.35A
5.35 A
14 A
18 A
3
-12 V
0.03 A
0.03A
0.03 A
0.5 A
0.8 A
Approx. 80% (230 VAC ), approx. 80% (120 VAC)
5 Vaux
0.3 A
0.3 A
0.3 A
2.0 A
2.0 A
1
2
Depends on the selected device configuration
The maximum total power of the voltage + 5 V and + 3.3 V amounts to 190 W at ATX power supply and 100 W at ATX redundant.
3
18 A for 20 seconds
4
2.5 A for 10 seconds
4
4
Typical power values
Component
Base device
Hard disk drive 1 × 3.5"
Hard disk drives 2 × 3.5"
SSD 2.5" drive
DVD burner drive
Current consumption
(AC-SV, U=230 V)
0.6 A
0.06 A
0.12 A
0.02 A
0.05 A
Power consumption
130 W
13.6 W
27.2 W
3.3 W
12.7 W
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
145
Technical specifications
8.4 Technical specifications
8.4.3 Power supply (AC)
Output voltage
Voltage
+ 12 V
1
+ 12 V
2
- 12 V
+ 5 V
+ 3.3 V
+ 5 Vaux
Max. current
11 A
14 A
0.3 A
25 A
1
20 A
1
2 A
Voltage stability
+/- 5 %
+/- 5 %
+/- 10 %
+/- 5 %
+/- 5 %
+ 5 % / - 3 %
1
The accumulated power of the +5 V and + 3.3 V supply may not exceed 190 W
Maximum inrush current at:
110 VAC = 25 A / 5 ms
230 VAC = 30 A / 5 ms
Power Good Signal
Figure 8-1 Timing profile of the Power Good Signal
146
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical specifications
8.4 Technical specifications
Note
Operation at an uninterruptible power supply (UPS)
The power supply contains an active PFC (Power Factor Correction) circuit to conform to the
EMC guidelines.
Uninterruptible AC power systems (UPS) must supply a sinusoidal output voltage in the normal and buffered mode when used with SIMATIC PCs with an active PFC.
UPS characteristics are described and classified in the standards EN 50091-3 and IEC
62040-3. Devices with sinusoidal output voltage in the normal and buffered mode are identified with the classification "VFI-SS-...." or "VI-SS-....".
8.4.4 AC power supply, redundant
Output voltage
Voltage
+ 12 V
+ 12 V
+ 12 V
- 12 V
+ 5 V
Max. current
18 A
18 A
14 A
0.8 A
20 A
2
2
2
1
Voltage stability
+/- 5 %
+/- 5 %
+/- 5 %
+/- 10 %
+ 5 % / - 4 %
+ 3.3 V
+ 5 Vaux
20 A
2.0 A
1
+ 5 % / - 4 %
+ 5 % / - 3 %
1
2
The accumulated power of the +5 V and + 3.3 V supply may not exceed 100 W.
The maximum accumulated current of the +12 V voltage must not exceed 24 A.
The maximum inrush current is for:
110 V AC: 25 A, 5 ms
230 V AC: 30 A, 5 ms
Note
Operation at an uninterruptible power supply (UPS)
The power supply contains an active PFC (Power Factor Correction) circuit to conform to the
EMC guidelines. Uninterruptible AC power systems (UPS) must supply a sinusoidal output voltage in the normal and buffered mode when used with SIMATIC PCs with an active PFC.
UPS characteristics are described and classified in the standards EN 50091-3 and IEC
62040-3. Devices with sinusoidal output voltage in the normal and buffered mode are identified with the classification "VFI-SS-...." or "VI-SS-....".
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
147
Technical specifications
8.5 Hardware description
8.4.5 Technical data of the telescopic rails
Ultimate load per pair
Full extraction length
Rail thickness
Mounting screws
8.5
8.5.1
8.5.1.1
Hardware description
At least 14 kg
At least 470 mm
Maximum 9.7 mm
M5 x 6 mm
Motherboard
Structure and functions of the motherboard
Core components of the motherboard: processor and chipset, three slots for memory modules, internal and external interfaces, Flash BIOS and the backup battery.
148
①
Slots for memory modules
②
Processor
③
Slot for the bus board
④
Backup battery
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
8.5.1.2
Technical specifications
8.5 Hardware description
Technical features of the motherboard
Component / interface
Chipset
Description
BIOS
CPU
Memory
Graphics
Expansion card slots
SATA interface
4
Parameters
Single chipset
•
Mobile Intel
®
8 chipset DH82C226 Express
(Platform Controller Hub)
Update by means of software • Insyde modified by Siemens
Intel
®
Core™ i
• VT and multimedia support
•
Turbo Boost and AMT, depending on CPU
• Onboard cache with 3M/4M depending on CPU
4 DIMM module slots, max. 8
GB per module
•
Data width of 64/72 bits (without ECC / with
ECC)
•
3.3 V
•
DDR3 1600-SDRAM in accordance with
PC3-12800 specification
•
2 to 4 Gbit chip size on the module
•
1600 MT/sec transfer rate
•
Variable from 2 GB to 8 GB / DIMM
•
With and without ECC
Integrated in the CPU
•
Intel® HD Graphics Controller, P4600/P4700
GT1/GT2
Graphics Controller integrated in processor with three independent 2-D and 3-D Engines.
• Intel® DH82C226 Express (Platform Controller Hub)
– VGA: 2560 × 1600/32-bit color depth/120
Hz
– DVI-D:
PCI, PCIe-Gen1,
PCIe-Gen2
2048 × 1152/32-bit color depth/60 Hz
DisplayPort: 4096 × 2160/32-bit color depth/24Hz
• Graphics memory:
Up to 1.7 GB, used in system memory, 32 MB reserved.
•
1 PCI 32-bit / PCIe-Gen2 4 Lanes. Type PCIex16 direct plug socket
•
1 PCIe-Gen3 16 Lanes, type PCIe-x16 direct plug socket
Various SATA modes, AHCI,
RAID 0, etc. can be set
•
6 interfaces
• Compatible to SATA-150/300/600
•
Supports NCQ (Native Command Queuing)
• 6 connectors
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
149
Technical specifications
8.5 Hardware description
Component / interface
Keyboard
Description
PS/2 keyboard interface
Parameters
• Standard
Mouse PS/2 mouse interface
•
Standard
Serial
Parallel
PROFIBUS/
MPI
2
PROFINET
2
•
COM1, 9-pin sub D
• COM2, 9-pin
Standard, bi-directional, EPP and ECP mode
SIMATIC S7 communication interface
Communication interface for
PROFINET
IO applications and SIMATIC installations
USB 2.0
•
V.24
Module connector for ribbon cable, with 9-pin sub
D at slot cover
Electrically isolated
Mbps
•
•
1
compatible to CP-5622, 12
10/100 Mbps, electrically isolated
1
CP -1616 compatible 3-port interface
USB
Universal Serial
Bus
3 high-current (500 mA) USB -2.0 ports, of those:
• 1 on the front
•
2 on the back
USB 3.0 4 high-current (500 mA) USB -3.0 ports, of those:
•
1 on the front
• 2 on the back
•
1 inside
Ethernet (two interfaces)
10BaseT/
100Base-TX/1000Base-TX
Ethernet 1:
Intel
®
Gigabit Network Connection (WGI210IT)
Ethernet 2:
Intel
®
Gigabit Network Connection (WGI217LM)
•
•
10/100/1000 Mbps, electrically isolated
•
Wake on LAN, remote boot
AMT-capable
5
, teaming-capable
1
• Supports jumbo frames up to 9014 bytes
•
With teaming capability
• Supports jumbo frames up to 9014 bytes
1
2
3
4
Electrical isolation within the safety extra-low voltage circuit (SELV)
Optional product variant
Depends on the CPU type
Depends on the selected device configuration
A floppy disk drive cannot be ordered using the configurator
5
AMT and teaming cannot be used simultaneously on the Ethernet interface
150
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
8.5.1.3 Position of the interfaces on the motherboard
Technical specifications
8.5 Hardware description
1 Audio input, audio output 10 PCIe Gen2/PCI 19 Port 80
2 DVI via DPP 11 SATA PS
28 2 × power supply ATX
20 Display and operator panel 29 PCIe Gen3
3 2 × PS/2
4 DPP
12 SATA 5
13 SATA 1
21 On/off button
22 Reset button
30 Processor socket
31 CPU XDP
5 COM 1, COM 2
6 USB 2.0/LAN 1
7 USB 3.0/LAN 2
8 PROFINET
9 PROFIBUS/MPI
14 SATA 0
15 SCSI LED
16 SATA 4
17 SATA 2
18 SATA 3
23 SAS
24 USB 3.0
25 USB 3.0/USB 2.0
26 BIOS
27 Power supply fan
32 Device fan
33 Memory modules
34 COM 1, COM 2
35 LPT
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
151
Technical specifications
8.5 Hardware description
8.5.1.4 External interfaces
Interface
COM1
COM2
LPT1
PS/2 mouse
Position Connector
External X30
Internal X504
Internal X501
External X25 P2
(7 to 12)
Description
9-pin standard plug
10-pin module plug for ribbon cable connection
26-pin module plug for ribbon cable connection
6-pin, miniature DIN socket (top socket)
PS/2 keyboard
USB 3.0
DPP
Microphone
Line out
External X25 P1
(1 to 6)
External X2 A, B
Internal
Internal
X563
X502
USB 2.0 External X4 A, B
PROFIBUS/MPI External X600
PROFINET External X3
Ethernet 1 and 2 External X4, X2
DVI-D
DPP
External X70
External X71
External X72
External X90 (top)
6-pin, miniature DIN socket (bottom socket)
USB3 Port 0, 1; USB2 Port 0, 1 interface side
USB3 Port 2; USB2 Port 2 (dongle interface)
USB3 Port 3; USB2 Port 3 (connection of display module)
USB2 Port 4, 5 interface side
9-pin, standard socket, electrically isolated interface
Port 0, 1, 2 RJ45
RJ45
24-pin DVI-D female connector
20-pin DisplayPort connector
20-pin DisplayPort connector
External X90 (bottom) 6-pin 3.5 mm jack
6-pin 3.5 mm jack
152
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Serial interfaces COM1, COM2 (V24), X30, X31, X504
Technical specifications
8.5 Hardware description
7
8
9
10
4
5
6
2
3
Pin no.
1
Short name
DCD (M5)
DSR (M1)
RxD (D2)
RTS (S2)
TxD (D1)
CTS (M2)
DTR (S1)
RI (M3)
GND (E2)
GND
Meaning
Receive signal (carrier)
Ready for operation
Receive data
Request to send
Send data
Clear to send
Data terminal ready
Incoming call
Functional ground (reference potential) -
-
Output
Input
Input / output
Input
Input
Input
Output
Output
Input
4
5
6
7
8
9
2
3
Pin no.
1
Short name
DCD (M5)
RxD (D2)
TxD (D1)
DTR (S1)
GND (E2)
DSR (M1)
RTS (S2)
CTS (M2)
RI (M3)
Meaning
Receive signal (carrier)
Receive data
Send data
Input / output
Input
Input
Output
Data terminal ready Output
Functional ground (reference potential) –
Ready for operation
Request to send
Input
Output
Clear to send
Incoming call
Input
Input
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
153
Technical specifications
8.5 Hardware description
Parallel interface LPT1, X501 module plug
11
13
15
17
19
21
23
25
2
3
4
Pinno.
1
7
8
5
6
9
10, 12, 14,
16, 18, 20,
22, 24, 26
Short name
/ Strobe (CLK)
/ AUTO FEED
Data - Bit 0
/ ERROR
Data - Bit 1
/ INIT
Data - Bit 2
/ SELECT IN
Data - Bit 3
Data - Bit 7
Data - Bit 4
Data - Bit 5
Data - Bit 6
Data - Bit 7
/ACK
BUSY
PE (PAPER END)
SELECT
Meaning
Data message
Automatically new line
Data channel 0
Device error
Data channel 1
Reset / Initialization
Data channel 2
Printer selection
Data channel 3
Ground
Data channel 4
Data channel 5
Data channel 6
Data channel 7
Data acknowledge
Not ready
Paper end
Device selection
Input / output
Output (open collector)
Output (open collector)
Output (TTL level)
Input (4.7 kΩ pull up)
Output (TTL level)
Output (open collector)
Output (TTL level)
Output (open collector)
Output (TTL level)
-
Output (TTL level)
Output (TTL level)
Output (TTL level)
Output (TTL level)
Input (4.7 kΩ pull up)
Input (4.7 kΩ pull up)
Input (4.7 kΩ pull up)
Input (4.7 kΩ pull up)
154
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Parallel interface LPT1
Technical specifications
8.5 Hardware description
9
10
11
12
13
14
15
16
17
18…25
7
8
5
6
2
3
4
Pinno.
1
Short name
/ Strobe (CLK)
Data - Bit 0
Data - Bit 1
Data - Bit 2
Data - Bit 3
Data - Bit 4
Data - Bit 5
Data - Bit 6
Data - Bit 7
/ACK
BUSY
PE (PAPER END)
SELECT
/ AUTO FEED
/ ERROR
/ INIT
/ SELECT IN
GND
Meaning
Data message
Data channel 0
Data channel 1
Data channel 2
Data channel 3
Data channel 4
Data channel 5
Data channel 6
Data channel 7
Data acknowledge
Not ready
Paper end
Device selection
Automatically new line
Device error
Reset / Initialization
Printer selection
Ground
PS/2 mouse interface, X25 7 to 12
Input / output
Output (open collector)
Output (TTL level)
Output (TTL level)
Output (TTL level)
Output (TTL level)
Output (TTL level)
Output (TTL level)
Output (TTL level)
Output (TTL level)
Input (4.7 kΩ pull up)
Input (4.7 kΩ pull up)
Input (4.7 kΩ pull up)
Input (4.7 kΩ pull up)
Output (open collector)
Input (4.7 kΩ pull up)
Output (open collector)
Output (open collector)
–
Pin no.
5
6
1
2
3
4
Short name
DAT
–
GND
P5VFK
CLK
–
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Meaning
Data channel, mouse
Not used
Ground
+ 5 V (fused)
Clock channel, mouse
Not used
Input output
Input/output
–
–
Output
Input/output
–
155
Technical specifications
8.5 Hardware description
PS/2 keyboard interface, X21 1 to 6
Pin no.
3
4
5
6
1
2
USB 2.0 ports, X4A, B; X561
Short name
DAT
–
GND
P5VFK
CLK
–
Meaning
Data channel, keyboard
Not used
Ground
+ 5 V (fused)
Clock channel, keyboard
Not used
–
–
Input output
Input/output
Output
Input/output
–
2
3
Pinno. Short name
1 VCC
4
– Data
+ Data
GND
Meaning
+ 5 V (fused)
Data channel
Data channel
Ground
The connectors are of type A.
The ports are rated as high-current USB 2.0 (500 mA).
Input / output
Output
Input / output
Input / output
–
156
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
PROFIBUS/MPI interface X9
1
Technical specifications
8.5 Hardware description
2
3
4
Pinno. Short name Meaning
1 – Not used
5
–
LTG_B
RTS_AS
M5EXT
Not used
Signal line B of MPI module
RTSAS, control signal for received data stream. The signal is "1" when the directly connected AS is sending.
M5EXT return line (GND) of 5 V power supply. The current load of an external consumer connected between P5EXT and M5EXT may not exceed the 90 mA.
6
7
8
P5 EXT
–
LTG_A
P5EXT power supply (+5 V) of the 5 V power supply. The current load of an external consumer connected between
P5EXT and M5EXT may not exceed the 90 mA.
Not used
Signal line A of the MPI module
9 RTS_PG
Shield
1
Optional product variant
RTS output signal of the MPI module. The control signal is
"1" when the programming device is sending. on connector casing
Input / output
–
–
Input/output
Input
Output
Output
–
Input/output
Output
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
157
Technical specifications
8.5 Hardware description
PROFINET LAN X3 Port P0, P1, P3
2
3
Pinno. Short name
1
4, 5
1
6
RD+
RD-
TD+
SYMR
TD-
Meaning
Receive data
2
Receive data
2
Send data
2
Internal 75 Ohm terminating resistor
Receive data
2
7, 8
S
1 SYMT-
LED 1
Internal 75 Ohm terminating resistor
Shield
Lit green: link
LED 2 Lights up yellow: activity
1
2
Optional product variant
Auto Negotiation and auto crossover are supported
Ethernet LAN connection, X2, X4
Input / output
Input
Input
Output
_
_
Output
158
8
S
5
6
7
3
4
Pinno. Short name
1
2
BI_DA+
BI_DA-
BI_DB+
BI_DC+
BI_DC-
BI_DB-
BI_DD+
BI_DD-
LED 1
LED 2
Meaning
Bi-directional data A+
Bi-directional data A-
Bi-directional data B+
Bi-directional data C+
Bi-directional data C-
Bi-directional data B-
Bi-directional data D+
Bi-directional data D-
Shield
Off: 10 Mbps
Lit in green color: 100 Mbps
Lit in orange color: 1000 Mbit/s
Lit: Active connection
(to a hub, for example)
Flashing: actvity
Input / output
Input / output
Input / output
Input / output
Input / output
Input / output
Input / output
Input / output
Input / output
–
–
–
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
VGA interface of the DVI-I/VGA adapter
Technical specifications
8.5 Hardware description
6
7
8
4
5
2
3
Pinno.
1
9
10
11
12
13
14
15
Short name
R
G
B
–
GND
GND
GND
GND
+ 5 V
GND
–
DDC_DAT
EXT_H
EXT_V
DDC_CLK
Meaning
Red
Green
Blue
Not used
Ground
Ground
Ground
Ground
+ 5 V (fused)
Ground
Not used
Display data channel data
Horizontal synchronizing pulse
Vertical synchronizing pulse
Display data channel clock
–
–
–
–
–
Input / output
Output
Output
Output
Output
–
–
Input/output
Output
Output
Input/output
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
159
Technical specifications
8.5 Hardware description
DVI-I interface, X70
19
20
21
22
23
24
10
11
12
13
14
15
16
17
18
7
8
9
5
6
1
2
3
4
C5
CSA
Pinno. Short name
S GND
S1
C1
GND
R
C2
C3
C4
G
B
HSYNC
GND
GND
TX2N
TX2P
GND
NC
NC
DDC CLK
DDC CLK
VSYNC
TX1N
TX1P
GND
NC
NC
+5 V
GND
MONDET
TX0N
TX0P
GND
NC
NC
GND
TXCP
TXCN
TDMS data 1+
Ground
Not used
Not used
+5 V
Ground
Hotplug detect
TDMS data 0-
TDMS data 0+
Ground
Not used
Not used
Ground
TDMS clock +
TDMS clock -
Meaning
Ground
Ground
Red
Green
Blue
Horizontal synchronizing pulse
Ground
Ground
TDMS data 2-
TDMS data 2+
Ground
Not used
Not used
DDC clock
DDC data
Vertical synchronizing pulse
TDMS data 1-
Input / output
–
–
Output
Output
Output
Output
–
–
–
–
Output
Output
–
Input / output
Input / output
Output
Output
Output
–
–
–
Output
–
Input
Output
Output
–
–
–
–
Output
Output
160
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Microphone interface, X60 bottom
Technical specifications
8.5 Hardware description
2
3
4
5
Pin no.
1
Short name
Right
7M
Sense
Left
M
Line Out interface, headset, X60 top
Meaning
Right channel
Input / output
Input
Analog ground Output
Switch contact for device identification Input
Left channel Input
Logic ground Output
8
9
Pin no.
5
6
7
Short name
M
Left
7M
Sense
Right
Meaning
Logic ground
Left channel
Analog ground
Input / output
Output
Output
Output
Switch contact for device identification Input
Right channel Output
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
161
Technical specifications
8.5 Hardware description
USB 3.0 port
9
7
8
4
5
6
2
3
Pin no.
1
DisplayPort port
Short name
VBUS
D-
D+
GND
RX-
RX+
GND
TX-
TX+
162
Meaning
+ 5 V (fused)
Data channel USB2
Data channel USB2
Ground
Data channel USB3
Data channel USB3
Ground
Data channel USB3
Data channel USB3
Input / output
Output
Input / output
Input / output
–
Input
Input
–
Output
Output
7
8
9
10
11
12
13
14
15
16
17
18
19
20
2
3
4
5
6
Pin no. Short description Meaning
1 ML_Lane0+ DP data 0+
GND
ML_Lane0-
ML_Lane1+
GND
ML_Lane1-
Ground
DP data 0-
DP data 1+
Ground
DP data 1-
ML_Lane2+
GND
ML_Lane2-
ML_Lane3+
GND
ML_Lane3-
CONFIG1 CAD
CONFIG2
AUX_CH+
GND
AUX_CH-
HPD
GND
DP_PWR
DP data 2+
Ground
DP data 2-
DP data 3+
Ground
DP data 3-
Cable Adapter Detect
Ground (PullDown)
Auxiliary channel+
Ground
Auxiliary channel-
Hot Plug Detect
Ground
+3.3V (fused)
Input / output
Output
-
Output
Output
-
Output
Output
-
Output
Output
-
Output
Input
-
Bidirectional
-
Bidirectional
Input
-
Output
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical specifications
8.5 Hardware description
8.5.1.5 Internal ports
Pin assignment of the internal interfaces
Interface
Memory
Bus expansion
Power supply
BIOS Recovery
Fan monitoring
SATA
Connection for PS serial
ATA
Position
Internal
Internal
Internal
Internal
Internal
Internal, e.g., hard disk
Internal
Connection for device fan Internal
Connection for SCSI LED Internal
Internal USB3/USB2 interface
Internal USB2 interface
Port 80 connector
COM2
LPT
Internal
Internal
Internal
Internal
Internal
Connector
X19, X20,
X190, X200
X508
Description
DIMM socket, 64-/ 72-bit
Bus expansion socket, used by PCI and
PCIe bus signals
X506, X507 4-pin 12 V ATX power connector
(CPU-VRM supply)
X593
X514 Monitoring of power supply fan, 8-pin, pin header
7-pin SATA connector X522, X523,
X524, X525,
X526, X527
X516, X517,
X518, X519,
X520, X521
Voltage supply for serial ATA
X512, X513,
X515
X595
X502
Power supply, device fan monitoring
(controlled), 4-pin, pin header
Input for SCSI drive activity display
X535, X536 Connection for USB interfaces on slot cover
X528
For connecting the USB cable to the front panel of the computer
Connection for Port 80 / mode switch
Connection for COM2 on slot cover (see external interfaces)
Connection for LPT on slot cover (see external interfaces)
Assignment of the SCSI activity connector, X595 Type JST B2B-PH-SM3-TB
Pin no.
1
2
Short name
NC
SCSI HD_N
Meaning
-
0-V level means that the SCSI interface is active
Input / output
-
Input
External Reset, X5, Type JST B2B-PH-SM3-TB
Pin no.
1
2
Short name
GND
Reset
Meaning
Ground
0 V level means reset
Input / output
-
Input
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
163
Technical specifications
8.5 Hardware description
External Power button, X529, Type JST B2B-PH-SM3-TB
Pin no.
1
2
Short name
EXT_PWRBTN
GND
Meaning Input / output
OV level means Power button pressed Input
Ground -
Pin assignment of the internal USB 2.0 interface connector, X535, X536
3
4
5
6
7
Pin no.
1
2
8
9
10
Short name
VCC
VCC
-Data USB1
-Data USB3
+Data USB1
+Data USB3
GND
GND
GND
Key
Meaning
+ 5 V (fused)
+ 5 V (fused)
Data channel
Data channel
Data channel
Data channel
Ground
Ground
Ground
–
-
–
–
Input / output
Output
Output
Input / output
Input / output
Input / output
Input / output
–
Pin assignment of the internal USB3/USB2 interface connector, X502
Pin no. Short name
USB3 (USB3/USB 2.0 contacts)
A1 VCC
A2
A3
SSRX-
SSRX+
A4
A5
A6
GND
SSTX-
SSTX+
B2
B3
B4, 5
B6
B7, 8
B9
B10
A7
A8
A9
A10
GND
-Data
+Data
Reserved
USB2 (USB 2.0 contacts)
B1 -Data
+Data
GND
NC
GND
NC
VCC
NC
Meaning
+ 5 V (fused)
Data channel USB3
Data channel USB3
Ground
Data channel USB3
Data channel USB3
Ground
Data channel USB2
Data channel USB2
+ 5 V (fused) or ground
Data channel USB2
Data channel USB2
Ground
Open
Ground
Open
+ 5 V (fused)
Open
164
Input / output
Output
Input
Input
-
Output
Output
–
Input / output
Input / output
Configurable
-
-
-
Input / output
Input / output
-
Output
-
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
SATA data interface, X522, 523, 524, 525, 526, 527
5
6
3
4
7
Pin no.
1
2
Short name
GND
TX-P
TX-N
GND
RX-N
RX-P
GND
Meaning
Ground
Transmitter positive
Transmitter negative
Ground
Receiver negative
Receiver positive
Ground
Technical specifications
8.5 Hardware description
Input / output
-
Output
Output
-
Input
Input
-
Pin assignment of the power supply fan monitoring interface, X514
3
4
5
6
7
Pin no.
1
2
8
Short name
Reserved
Reserved
Reserved
Tacho signal
PS_Status
Meaning
-
PWM, speed setting ATX AC-SV
-
Monitoring signal
Status of redundant power supply
Input / output
-
Output
Input
Input
Input
Reserved Reserved for fan error or redundant power supply Input
Quittung_Status Acknowledgment of acoustic alarm signal of redundant power supply (signal is open when module is switched on)
Output
Ground - -
Pin assignment of fan interface X512, X513, X515
2
3
Pin no.
1
4
Short name
GND
VCC
Tacho signal
PWM
Meaning
Ground
+12 V fused
Monitoring signal
Speed setting
Input / output
-
Output
Input
Output
Pin assignment of the supply for the serial ATA drives X516, 517, 518, 519, 520, 521
3
4
5
Pin no. Short name
1 +12 V
2 GND
GND
+5 V
+3.3 V
Meaning
Power supply
Ground
Ground
Power supply
Power supply
Input / output
Output
–
–
Output
Output
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
165
Technical specifications
8.5 Hardware description
Pin assignment of the PEG interface (PCIe X16 socket), X610
Signal
P12V
P12V
P12V
GND
SMB_CLK2
SMB_DATA2
GND
P3V3 n.c.
AUX_3V
WAKE2 n.c.
GND
PCIEX16_TX_P(15)
PCIEX16_TX_N(15)
GND
SDVO_CTRLCLK
GND
PCIEX16_TX_P(14)
PCIEX16_TX_N(14)
GND
GND
PCIEX16_TX_P(13)
PCIEX16_TX_N(13)
GND
GND
PCIEX16_TX_P(12)
PCIEX16_TX_N(12)
GND n.c.
SDVO_CTRLDATA
GND
PCIEX16_TX_P(11)
PCIEX16_TX_N(11)
GND
GND
PCIEX16_TX_P(10)
PCIEX16_TX_N(10)
GND
GND
B34
B35
B36
B37
B38
B39
B40
B27
B28
B29
B30
B31
B32
B33
B20
B21
B22
B23
B24
B25
B26
B13
B14
B15
B16
B17
B18
B19
Pin no. Pin no. Signal
B1 A1
B2 A2
B3
B4
B5
B6
A3
A4
A5
A6
B7
B8
B9
B10
B11
B12
A7
A8
A9
A10
A11
A12
A20
O21
A22
A23
A24
A25
A26
A13
A14
A15
A16
A17
A18
A19
A34
A35
A36
A37
A38
A39
A40
A27
A28
A29
A30
A31
A32
A33
P12V
P12V
P12V
GND n.c. n.c. n.c. n.c.
P3V3
P3V3
PCIE_RESET_L
GND
PCIE0_ECLK
PCIE0_ECLK_N
GND
PCIEX16_RX_P(15)
PCIEX16_RX_N(15)
GND n.c.
GND
PCIEX16_RX_P(14)
PCIEX16_RX_N(14)
GND
GND
PCIEX16_RX_P(13)
PCIEX16_RX_N(13)
GND
GND
PCIEX16_RX_P(12)
PCIEX16_RX_N(12)
GND n.c. n.c.
GND
PCIEX16_RX_P(11)
PCIEX16_RX_N(11)
GND
GND
PCIEX16_RX_P(10)
PCIEX16_RX_N(10)
166
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Signal
PCIEX16_TX_P(9)
PCIEX16_TX_N(9)
GND
GND
PCIEX16_TX_P(8)
PCIEX16_TX_N(8)
GND
MCH_CFG_20
GND
PCIEX16_TX_P(7)
PCIEX16_TX_N(7)
GND
GND
PCIEX16_TX_P(6)
PCIEX16_TX_N(6)
GND
GND
PCIEX16_TX_P(5)
PCIEX16_TX_N(5)
GND
GND
PCIEX16_TX_P(4)
PCIEX16_TX_N(4)
GND
GND
PCIEX16_TX_P(3)
PCIEX16_TX_N(3)
GND
GND
PCIEX16_TX_P(2)
PCIEX16_TX_N(2)
GND
GND
PCIEX16_TX_P(1)
PCIEX16_TX_N(1)
GND
GND
PCIEX16_TX_P(0)
PCIEX16_TX_N(0)
GND n.c. n.c.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical specifications
8.5 Hardware description
B74
B75
B76
B77
B78
B79
B80
B81
B82
B67
B68
B69
B70
B71
B72
B73
B60
B61
B62
B63
B64
B65
B66
B53
B54
B55
B56
B57
B58
B59
Pin no. Pin no. Signal
B41 A41
B42 A42
B43
B44
B45
B46
A43
A44
A45
A46
B47
B48
B49
B50
B51
B52
A47
A48
A49
A50
A51
A52
A60
A61
A62
A63
A64
A65
A66
A53
A54
A55
A56
A57
A58
A59
A74
A75
A76
A77
A78
A79
A80
A81
A82
A67
A68
A69
A70
A71
A72
A73
GND
GND
PCIEX16_RX_P(9)
PCIEX16_RX_N(9)
GND
GND
PCIEX16_RX_P(8)
PCIEX16_RX_N(8)
GND n.c.
GND
PCIEX16_RX_P(7)
PCIEX16_RX_N(7)
GND
GND
PCIEX16_RX_P(6)
PCIEX16_RX_N(6)
GND
GND
PCIEX16_RX_P(5)
PCIEX16_RX_N(5)
GND
GND
PCIEX16_RX_P(4)
PCIEX16_RX_N(4)
GND
GND
PCIEX16_RX_P(3)
PCIEX16_RX_N(3)
GND
GND
PCIEX16_RX_P(2)
PCIEX16_RX_N(2)
GND
GND
PCIEX16_RX_P(1)
PCIEX16_RX_N(1)
GND
GND
PCIEX16_RX_P(0)
PCIEX16_RX_N(0)
GND
167
Technical specifications
8.5 Hardware description
Pin assignment of the PCI-PCIe interface (PCIe X16 socket), X10
Signal
N12V
P12V
P12V
GND
PCI_INT_N(7)
PCI_INT_N(5)
P5V
PCI_REQ_N(4)
PCI_REQ_N(3)
GND
PCI0_PCLK
GND
PCI1_PCLK
GND
PCI_REQ_N(1)
PCI_REQ_N(2)
P5V
PCI_AD(31)
PCI_AD(29)
GND
PCI_AD(27)
PCI_AD(25)
P3V3
PCI_CBE_N(3)
PCI_AD(23)
GND
PCI_AD(21)
PCI_AD(19)
P3V3
PCI_AD(17)
PCI_CBE_N(2)
GND
IRDY
P3V3
DEVSEL
GND
PLOCK
PERR
P3V3
SERR
B34
B35
B36
B37
B38
B39
B40
B27
B28
B29
B30
B31
B32
B33
B20
B21
B22
B23
B24
B25
B26
B13
B14
B15
B16
B17
B18
B19
Pin no. Pin no. Signal
B1 A1
B2 A2
B3
B4
B5
B6
A3
A4
A5
A6
B7
B8
B9
B10
B11
B12
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
O21
A22
A23
A24
A25
A26
A34
A35
A36
A37
A38
A39
A40
A27
A28
A29
A30
A31
A32
A33
AUX_5V
P12V
P12V
GND
PCI_INT_N(6)
PCI_INT_N(8)
P5V
P5V
PCI_GNT_N(4)
PCI_GNT_N(3)
AUX_3V
PLT_RST_N_BUFF
GND
PCI_GNT_N(1)
PCI_GNT_N(2)
GND
PME
PCI_AD(30)
P3V3
PCI_AD(28)
PCI_AD(26)
GND
PCI_AD(24) n.c.
P3V3
PCI_AD(22)
PCI_AD(20)
GND
PCI_AD(18)
PCI_AD(16)
P3V3
FRAME
GND
TRDY
GND
STOP
P3V3
SMB_CLK1
SMB_DAT1
GND
168
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Signal
P3V3
PCI_CBE_N(1)
PCI_AD(14)
GND
PCI_AD(12)
PCI_AD(10)
GND
PCI_AD(8)
PCI_AD(7)
P3V3
PCI_AD(5)
PCI_AD(3)
GND
PCI_AD(1)
P5V
P5V
P5V
AUX_5V
WAKE1
GND
GND n.c. n.c.
GND
GND
PCIE_RX_P(1)
PCIE_RX_N(1)
GND
GND
PCIE_TX_P(2)
PCIE_TX_N(2)
GND
GND
PCIE_TX_P(3)
PCIE_TX_N(3)
GND
GND
PCIE_TX_P(4)
PCIE_TX_N(4)
GND
RESERVE1 *)
RESERVE2 *)
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical specifications
8.5 Hardware description
B74
B75
B76
B77
B78
B79
B80
B81
B82
B67
B68
B69
B70
B71
B72
B73
B60
B61
B62
B63
B64
B65
B66
B53
B54
B55
B56
B57
B58
B59
Pin no. Pin no. Signal
B41 A41
B42 A42
B43
B44
B45
B46
A43
A44
A45
A46
B47
B48
B49
B50
B51
B52
A47
A48
A49
A50
A51
A52
A53
A54
A55
A56
A57
A58
A59
A60
A61
A62
A63
A64
A65
A66
A74
A75
A76
A77
A78
A79
A80
A81
A82
A67
A68
A69
A70
A71
A72
A73
PAR
PCI_AD(15)
P3V3
PCI_AD(13)
PCI_AD(11)
GND
PCI_AD(9)
PCI_CBE_N(0)
P3V3
PCI_AD(6)
PCI_AD(4)
GND
PCI_AD(2)
PCI_AD(0)
P5V
P5V
PCIE_1X4X
GND
PLT_RST_N_PCIE4X
PS_ON
PS_PWRGD
GND
GND
PCIE_TX_P(1)
PCIE_TX_N(1)
GND
GND
PCIE1_ECLK
PCIE1_ECLK_N
GND
GND
PCIE_RX_P(2)
PCIE_RX_N(2)
GND
GND
PCIE_RX_P(3)
PCIE_RX_N(3)
GND
GND
PCIE_RX_P(4)
PCIE_RX_N(4)
GND
169
Technical specifications
8.5 Hardware description
NOTICE
Note for bus modules with PCIe switch
As long as no modules are plugged into the PCIe slots behind a PCIe switch, the IRQs are not used by the PCIe switch, but the display only shows that these IRQs would be used if modules were plugged in.
The PCIe switch is displayed in Windows Device Management as "PCI standard PCI-to-
PCI bridge".
8.5.2
8.5.2.1
Bus board
Bus board models
Riser cards are used as bus boards. These riser cards are used to a create spatial offset for connections between the motherboard and the expansion cards. This positions the bus board vertical and expansion cards parallel to the motherboard.
Depending on your device configuration, one of the following bus board models is mounted in your device.
When plugging the PCI/PCIe cards observe the slot specification. The same number of PCIe slots of the third generation (Gen. 3) are twice as powerful as slots of the second generation
(Gen. 2).
Bus board 2 x PCIe with piggyback 2 x PCIe
The following figure shows the bus board at the top and the piggyback on the bottom.
170
①
Slot PCIe x4 Gen. 3
②
Slot PCIe x4 Gen. 2
③
Slot PCIe x4 Gen. 3, piggyback
④
Slot PCIe x8 Gen. 3, piggyback
Corresponding designation on the device front: Slot 2
Corresponding designation on the device front: Slot 3
Corresponding designation on the device front: Slot 4
Corresponding designation on the device front: Slot 1
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical specifications
8.5 Hardware description
Bus board without piggyback 2 x PCIe
Corresponds to the model in the last figure, without piggyback. Only the slots in Slot 2 (Item
①
) and Slot 3 (Item
②
) can be equipped with PCIe cards.
Bus board 2 × PCI with piggyback 2 × PCIe
The following figure shows the bus board at the top and the piggyback on the bottom.
①
Slot PCI
②
Slot PCI
③
Slot PCIe x8 Gen. 3, piggyback
④
Slot PCIe x8 Gen. 3, piggyback
Corresponding designation on the device front: Slot 2
Corresponding designation on the device front: Slot 3
Corresponding designation on the device front: Slot 4
Corresponding designation on the device front: Slot 1
8.5.2.2 PCI hardware interrupts
Applications demanding high-performance interrupt handling require high-speed hardware interrupt reaction. The PCI hardware interrupt should only be used by one resource in order to ensure high-speed reaction of the hardware.
Setting up an exclusive interrupt on the device (only APIC mode)
An exclusive interrupt can only be used with bus board 2 × PCI with piggyback 2 x PCIe at
PCI slot 2 and PCI slot 3. Further exclusive interrupts for use at the slots are not available.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
171
Technical specifications
8.5 Hardware description
Assigning exclusive interrupts in BIOS Setup (PIC mode only)
The interrupts are automatically assigned to the slots at system startup due to the default settings in system BIOS.
Several slots may share the same interrupt, depending on the system configuration. This functionality is known as interrupt sharing. Exclusive interrupts are not available in PIC mode. Disable specific system resources in order to obtain exclusive interrupts. The resulting free interrupt is then assigned to the slots. The lower free IRQ is assigned to the lower Slot
No.
If a conflict arises through the assignment, a message will be displayed and has to be acknowledged.
Message: "Resources Conflict. Please re-select [ok]"
The interface that causes the conflict is disabled automatically. Additional information is
available in the section Interrupt assignments (Page 179).
Example
If you want to use "IRQ 3" for a slot, you have to disable the "Internal COM 2" by using
Advanced > Peripheral Configuration. IRQ 3 is then assigned automatically to the slot that has the lowest slot number.
Ethernet 1
Ethernet 2
IRQ assignments for Windows (APIC mode)
16
1, 2
17
1
PROFIBUS/MPI
PCI slot 1
PCI slot 2
PCI Express slot
19
20
21
16
1
1
1
1, 3
1)
2)
3)
Requirement: The modules in the PCI slots each require only one interrupt
Requirement: VGA and PCI Express do not require an interrupt
Requirement: VGA does not require an interrupt and Ethernet1 is disabled
172
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Interrupt assignment bus board 4 x PCIe
Technical specifications
8.5 Hardware description
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
173
Technical specifications
8.5 Hardware description
Interrupt assignment bus board 2 x PCIe
174
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Interrupt assignment bus board 2 × PCI / 2 x PCIe
Technical specifications
8.5 Hardware description
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
175
Technical specifications
8.5 Hardware description
8.5.3
8.5.3.1
System resources
Currently allocated system resources
All system resources (hardware addresses, memory configuration, allocation of interrupts,
DMA channels) are assigned dynamically by the Windows OS, depending on the hardware configuration, drivers and connected external devices. You can view the current configuration of system resources or possible conflicts with the following operating systems:
Windows 7 Start > Enter "msinfo32" in the search function
8.5.3.2 Allocation of the system resources used by BIOS/DOS
The following tables describe the system resources for the factory state of the device.
I/O address allocation
The following tables describe the system resources in the factory state of the device.
Static area
I/O address
(hex)
From To
0000 001F
0020 0021
0022 0023
0024 0025
0026 0027
0028 0029
002A 002B
002C 002D
002E 002F
0030 0031
0032 0033
0034 0035
0036 0037
0038 0039
003A 003B
003C 003D
003E 003F
0040 0043
0044 004D
004E 004F
0050 0053
Size
[byte]
Description of the basic function
32 DMA controller
2 Programmable interrupt controller
2 <Not used>
2 Programmable interrupt controller
2 <Not used>
2 Programmable interrupt controller
2 <Not used>
2 Programmable interrupt controller
2 Motherboard resources
2 Programmable interrupt controller
2 <Not used>
2 Programmable interrupt controller
2 <Not used>
2 Programmable interrupt controller
2 <Not used>
2 Programmable interrupt controller
2 <Not used>
4 System timer
10 <Not used>
2 Motherboard resources
4 System timer
Alternative function
176
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical specifications
8.5 Hardware description
I/O address
(hex)
From To
0054 005F
0060 0060
0061 0061
0062 0062
0063 0063
0064 0064
0065 0065
0066 0066
0067 0067
0068 006F
0070 0070
0070 0077
0078 007F
0080 0080
0081 0091
0092 0092
0093 009F
00A0 00A1
00A2 00A3
00A4 00A5
00A6 00A7
00A8 00A9
00AA 00AB
00AC 00AD
00AE 00AF
00B0 00B1
00B2 00B3
00B4 00B5
00B6 00B7
00B8 00B9
00BA 00BB
00BC 00BD
00BE 00BF
00C0 00DF
00E0 00EF
00F0 00F0
00F1 0277
0278 027F
0280 02E7
02E8 02EF
Size
[byte]
Description of the basic function Alternative function
12 <Not used>
1 Keyboard controller
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
Motherboard resources
<Not used>
Motherboard resources
Keyboard controller
Motherboard resources
<Not used>
Motherboard resources
8
8
8
1
<Not used>
Motherboard resources
System CMOS/real-time clock
<Not used>
1 Motherboard resources
17 DMA controller
1 Motherboard resources
13 DMA controller
2
2
2
Programmable interrupt controller
<Not used>
Programmable interrupt controller
<Not used>
Programmable interrupt controller
<Not used>
Programmable interrupt controller
<Not used>
Programmable interrupt controller
Motherboard resources
Programmable interrupt controller
<Not used>
Programmable interrupt controller
<Not used>
2
2
Programmable interrupt controller
<Not used>
32 DMA controller
16 <Not used>
1 Numeric data processor
391 <Not used>
8 <Reserved>
104 <Not used>
8 <Reserved>
Cascaded
Reserved for LPT1
Reserved for COM1 or COM2
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
177
Technical specifications
8.5 Hardware description
I/O address
(hex)
From To
02F0 02F7
02F8 02FF
0300 0377
0378 037F
0380 03AF
03B0 03BB
03BC 03BF
03C0 03DF
03E0 03E7
03E8 03EF
03F0 03F7
03F8 03FF
Size
[byte]
Description of the basic function
8 <Not used>
8 COM2
120 <Not used>
8 LPT1
48 <Not used>
12 Graphics
4 <Reserved>
32 Graphics
8 <Not used>
8 <Reserved>
8 <Not used>
8 COM1
Alternative function
Can be deactivated in setup, then free
Reserved for COM1 or COM2
Can be deactivated in setup, then free
Reserved for LPT1
Reserved for COM1 or COM2
Can be deactivated in setup, then free
Reserved for COM1 or COM2
Dynamic range – resources are managed by means of Plug and Play functionality
I/O address
(hex)
From To
0400 0453
04D0 04D1
0680 069F
0800 087F
164E 164F
1800 18FE
1854 1857
2004 2007
FFFF FFFF
Size
[byte]
Description of the basic function Alternative function
84 Motherboard resources
2 Programmable interrupt controller
32 Motherboard resources
128 Motherboard resources
2 Motherboard resources
255 Motherboard resources
4 Motherboard resources
4 Motherboard resources
1 Motherboard resources
Cascaded
178
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical specifications
8.5 Hardware description
Interrupt assignments
The functions are assigned different interrupts, depending on the operating system. A distinction is made between the PIC and APIC modes.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
179
Technical specifications
8.5 Hardware description
PCI / PCIe cards and the on-board PCI / PCIe devices require PCI interrupt channels. These interrupt channels can be shared and are plug-and-play compatible, that is, several devices can share the same interrupt. The IRQ is assigned automatically.
PCI interrupt channels must be derived from the PIC interrupt pool, that is PCI modules also use PIC resources. These IRQ channels are assigned automatically.
The Host PCI IRQ channels A to H are permanently assigned in APIC mode. These default settings cannot be modified.
The host PCI IRQ channels A to H in PIC mode are assigned automatically by the BIOS. The assignment can be changed by disabling functions. You can also assign free IRQs to the host PCI IRQ line in the BIOS menu "PCI Configuration".
Memory address assignments
PCI VGA modules can be operated with expansion ROM up to 48K.
Address from to
0000 0000 0007 FFFF
0008 0000 0009 F7FF
0009 F800 0009 FFFF
000A 0000 000A FFFF
000B 0000 000B 7FFF
000B 8000 000B FFFF
Size
512 K
127 k
2 K
64 K
32 K
32K
000C 0000 000C BFFF 48 K
000C 0000 000C E9FF
000C F000 000D FFFF
59 K
68 K
1
1
Description of the basic function Possible alternative function
Conventional system memory
Conventional system memory extended
XBDA, extended Bios Data Area
VGA graphics refresh memory Shared SMM for power management
SW graphics / text refresh memory
Not used
VGA graphics/text refresh memory
VGA BIOS expansion
VGA BIOS
Not used (no RAID, no PXE)
Always occupied via EMM High DOS
Memory
000C F000
000D 0000
000C F000
000D 3800
000C FFFF
000D FFFF
000D 37FF
000D FFFF
4 K 1
64 K
18 K
50 K
1
1
1
PXE
Not used (no RAID, with PXE) via EMM High DOS
Memory
RAID
Not used (RAID, no PXE)
RAID and PXE
Not used via EMM High DOS
Memory
000C F000 000D 47FF
000D 4800 000D FFFF
000E 0000 000E 1FFF
000E 2000 000E 3FFF
000E 4000 000F FFFF
22 K
46 K
8 k
8 k
1
1
112 K
USB
DMI data
System BIOS
0010 0000 CFFF FFFF 3.25 GB System memory 4 GB memory configuration
E000 0000 FFEF FFFF 511 MB PCIe Configuration Space
FFF0 0000 FFFF FFFF 1 MB Firmware HUB
1
32 GB RAM expansion
Optional memory allocation, depending on settings in BIOS Setup
Depends on memory configuration
180
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
8.5.4
8.5.4.1
Technical specifications
8.5 Hardware description
Displays and operator panel
Design and function
The operator panel is interconnected with the motherboard via a 26-pin flat cable. The flat cable is plugged in at Position the right.
②
and secured by sliding the lock
①
at the plug connector to
①
Lock plug connector
②
Plug connector, connection to the motherboard
③
Connection for external reset
④
LEDs
⑤
USB socket, only the top USB contact is used
⑥
Reset button, 1-pin
⑦
On-Off button, 1-pin
⑧
USB 3.0 port
Pin assignment of the OP connectors 8.5.4.2
External Reset
⑦
type: JST B2B-PH-SM3-TB
Pin no.
1
2
Short name
PWR Good
GND
Meaning
External reset, (IO low max. 30 mA)
Ground
Input / output
The device is reset when pins 1 and 2 (for example, by means of a pushbutton) are shortcircuited. It remains in this state until the short-circuit is cleared.
Note
Contact Customer Support or the Repair Center for detailed information on pin assignments of the interfaces.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
181
Technical specifications
8.5 Hardware description
8.5.5 Communication processor CP 1616 onboard
8.5.5.1
Properties
Introduction
CP 1616 on-board allows you to connect IPCs to Industrial Ethernet.
The basic characteristics of the PCS 1616 onboard are:
● Optimized for PROFINET IO
● Enhanced Real Time Ethernet Controller 400 = ERTEC 400
● The connectors are designed for 10BaseT and 100BaseTX.
● Data transfer rates of 10 and 100 Mbps in full/half duplex mode are supported.
● The handshake is performed automatically (auto negotiation).
● Autocrossing
● Automatic hardware detection
● Integrated 3-port real-time switch
3-port real-time switch
The switch function of the 3-port real-time switch is maintained in the following cases:
● Restart (Windows Restart)
● Reset (using the shortcut <Ctrl-Alt-Del)
The switch function is interrupted in the following cases:
● Shutting down with Windows command
● Activating the on/off switch
● Shutting down with power switch (on/off switch).
Three RJ45 connectors
Terminal devices or other network components can be connected to the three RJ45 sockets that lead to the integrated real-time switch. The CP 1616 is connected to the LAN (Local
Area Network) via one of the three RJ45 sockets of the device.
Typical Communication Partners
CP 1616 onboard as an IO controller
The following diagram shows a typical application: CP 1616 onboard as PROFINET IO controller on the IO controller layer.
The IO base controller user program runs on the PC. This program accesses the functions of the IO base user program interface.
182
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical specifications
8.5 Hardware description
Data traffic is routed via the communication processor to several SIMATIC S7 PROFINET IO devices, ET 200S over Industrial Ethernet.
CP 1616 onboard as IO device
The following diagram shows a typical application: Two PCs each with a CP as a PROFINET
IO device on the IO device layer.
A PC with a CP as PROFINET IO controller, a SIMATIC S7-400 with a CP 443-1 as
PROFINET IO controller and two SIMATIC S7 ET 200S PROFINET IO devices are also connected in the network.
The IO base device user program runs on the IO device PC. This program accesses the functions of the IO base user program interface. Data traffic is routed via the CP 1616 onboard communication processor to a PC as PROFINET IO controller, or to an S7-400 automation system with CP 443-1 over Industrial Ethernet.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
183
Technical specifications
8.5 Hardware description
8.5.5.2 Firmware loader
Firmware loader
When to load firmware
The CP 1616 onboard is supplied with the latest version of the firmware. If new functions become available due to product development, you can make them available by performing a firmware download.
Description
This section will familiarize you with the application area and use of the firmware loader. You can find additional, detailed information about the individual loader variants in the integrated help of the program.
Firmware
This refers to the system program in the SIMATIC NET modules.
Application area for the firmware loader
The firmware loader enables you to reload new firmware releases to SIMATIC NET modules.
It is used for:
● PROFIBUS modules
● Industrial Ethernet modules
● Modules for gateways, for example, IE/PB link
Installation
The firmware loader is available on your PG/PC under Windows following the installation of
STEP 7/NCM PC.
Loader files
The firmware loader supports the following file types:
● <file>.FWL
A file form that contains further information, which is displayed by the firmware loader.
The firmware loader can use this information to check if the firmware is compatible to the device.
Read the information provided along with the loader file, for example, in the readme file. This information is also displayed in the firmware loader when the FWL file is loaded.
184
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical specifications
8.5 Hardware description
Loading firmware
Start downloading procedure
1. In the Windows Start menu, select the menu command SIMATIC > STEP 7 > NCM S7 >
Firmware Loader.
2. Click "Next" and follow the instructions in the dialog fields that follow. A help function is integrated in the software as support.
Note
Ensure that the loader file you are using for the update is suitable for the version of firmware on your module. If you have any doubts, contact your local Siemens consultant.
Note
Be aware that aborting the loading process may result in an inconsistent state in your module.
You can find additional, detailed information about the individual loader variants in the integrated help.
Note
When loading the firmware or commissioning the module, be aware that the CP 1616 onboard takes five MAC addresses (always in direct sequence). The first two addresses are displayed in the BIOS, in the "Peripheral Configuration" submenu of the "Advanced" menu.
Example
The lower MAC address at "Profinet" is provided for Layer 2 communication, while the second one is used for Ethernet/PROFINET communication.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
185
Technical specifications
8.6 BIOS description
8.5.5.3 Further actions in STEP 7/NCM PC
Configuring
8.6
8.6.1
Your PC is now ready, although you still have to configure the SIMATIC NET communication software. The rest of the procedure is described in the "Commissioning PC Stations" manual
(on the Windows PC that also contains STEP 7/NCM PC: Start > Simatic > Documentation >
English > Commissioning PC Stations).
BIOS description
Overview
BIOS Setup program
The BIOS Setup program, or BIOS Setup for short, is located, together with the setup parameters, in a FLASH block on the motherboard.
You change the setup parameters of the device in the BIOS Setup. Examples: System time, hard disks or boot order.
Changing the device configuration
Your device configuration is preset for operating with the included software. You should only change the default setup parameters if you have made technical changes to your device, or if a fault occurs when the device is switched on.
NOTICE
Malfunctions can occur with running software CPU
If a BIOS update of the PC is performed while SIMATIC software controller, a SIMATIC
WinAC for example, is running, the software CPU can malfunction, resulting in communication interruptions or failures, for example. Other actions that put a heavy load on the PC hardware, for example, running hardware tests such as benchmarks, can result in malfunctions of the software CPU.
Do not run a BIOS update or other actions that would put a heavy load on the hardware during operation of a software CPU.
Switch the software CPU to "STOP" before you run a BIOS update or perform other critical actions.
Note
Documentation
BIOS Setup is described for all devices and device configurations. Some BIOS submenus or
Setup parameters may not be included, depending on your order. The interface of your BIOS
Setup can deviate from the figures in this document.
You can find a detailed description of the BIOS on the Support website under Entry ID
92189185 ( http://support.automation.siemens.com/WW/view/en/92189185 ).
186
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical specifications
8.6 BIOS description
8.6.2
Procedure
Opening the BIOS selection menu
1. Reset the device (warm or cold restart).
Depending on the device version, the default settings can differ from the figures shown.
The following message appears briefly on the display at the end of the self-test:
Press ESC for boot options
2. Press <ESC> to open the BIOS selection menu:
The following keys are available in the BIOS selection menu:
Buttons
Continue
Boot Manager
Function
Exit selection menu, continue start sequence
Specify the boot media from which to boot:
• Hard disk drive
•
CD-ROM drive
• USB drive
Device Management Start device manager for UEFI boot media
Boot From File Boot Maintenance Manager:
•
Boot Options: Set boot order
• Driver Options: Configure drivers
•
Console Options: Configure connected input device
• Boot from File: Start from an ".EFI" file
•
Reset System: Restore factory settings
Secure Boot Option
1
Configuration settings to start the device in Secure Boot mode. The only software modules loaded are those that are known to be safe for the
BIOS or the operating system.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
187
Technical specifications
8.6 BIOS description
Buttons
SCU
BIOS Update
MEBx
Function
Start BIOS Setup via Setup Configuration Utility
Update BIOS from USB memory stick
Start Intel Management Engine BIOS Extension from Active Management Technology Support (AMT)
1
Available as of Windows 8 or later
8.6.3 Configuration
The individual setup parameters are distributed between different menus and submenus.
The menus always have the same layout.
Menu layout
The following figure is an example for the main menu. Device-specific information is shown as blurred.
188
①
Header
②
Menu bar
③
Settings, submenus and device-specific information
④
Help area
⑤
Key assignment
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
8.6.4
Technical specifications
8.6 BIOS description
A menu is divided into four areas:
● In the menu bar
②
on top, you select from the different menus "Main", "Advanced", etc.
● The center left area
③
includes information on your device and you can edit settings that are partly available in submenus.
● The center right area parameters.
④
displays short help texts for the currently selected setup
● The key assignment in BIOS Setup.
⑤
at the bottom shows the function keys and control keys available
You can toggle between the menus with the "←" left and "→" right cursor keys.
The following table shows the standard menus. Not all menus are included in each supplied device configuration.
Menu
Main
Advanced
Security
Power
Boot
Exit
Meaning
Display system information, for example, BIOS version, processor and memory
Configure hardware using different submenus
Security functions, e.g., setting a password
Specify CPU settings and switch-on functions.
Determine boot options, e.g., boot order
Save and exit (see Exit menu)
Exit menu
You always exit BIOS Setup in this menu.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
189
Technical specifications
8.6 BIOS description
Exit Saving Changes All changes are saved and the system is restarted with the new Setup parameters.
Save Change Without
Exit
Exit Discarding
Changes
All changes are saved.
All changes are discarded and the system is restarted with the old Setup parameters.
Load Optimal Defaults All setup parameters are reset to the safe default values.
Notice: The existing Setup parameters are overwritten by this.
Load Custom Defaults The profile must be loaded with the custom Setup parameters.
Requirement: The parameters are saved prior to this with "Save Custom
Defaults".
Save Custom Defaults The currently configured Setup parameters are saved as a custom profile
(see also "Load Custom Defaults").
Discard Changes All changes are discarded.
8.6.5 BIOS update
Check regularly if updates are available for download to your device.
Additional information can be found on the Internet at the following address:After Sales
Information system ( http://www.siemens.com/asis ).
Noting down and restoring BIOS Setup settings
NOTICE
Irretrievable loss of data
All BIOS Setup settings are deleted after the BIOS update. This can put the system in an undefined state. This may damage the device and the plant.
1. Print out the table in the next section "General BIOS Setup settings".
2. Enter your specific BIOS Setup setting in this table before you run a BIOS update.
3. Start BIOS Setup after the BIOS update.
4. Load the BIOS Setup default settings with <F9> "Setup Defaults". Or use the BIOS
Setup command "Load Optimal Defaults" in the "Exit" menu.
5. Make your own Setup settings based on the table you have printed out.
6. Save the BIOS Setup settings with <F10> "Save and Exit".
190
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Performing a BIOS update
NOTICE
Damage to the device
If you switch off the device during the update, the BIOS will be incomplete and corrupt. This may result in malfunctions.
Leave the device switched on during the update.
If you have purchased a new BIOS update for your device, follow these steps to install the update:
1. Copy the update to a USB memory stick.
2. Reset the device (warm or cold restart).
The following message appears briefly on the display at the end of the self-test:
Press ESC for boot options
3. Press <ESC> to open the BIOS selection menu.
4. Click the "BIOS Update" button.
5. Follow the instructions on the screen.
Reboots
Technical specifications
8.6 BIOS description
There may be several reboots after a BIOS update. These reboots are initiated by the
Management Engine (ME). The reboots are required by the ME to adapt itself to the changes of the BIOS update.
8.6.6 BIOS Setup settings
If you have changed any default settings in Setup, you can enter them in the following table.
You can then refer to these entries for any future hardware modifications.
Note
Print out the table below and keep the pages in a safe place once you made your entries.
The default setup settings vary depending on the ordered device configuration.
BIOS Setup settings
Main
System parameters
System Time
System Date
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Default settings
00:00:00
MM/DD/YYYY
Local settings
191
Technical specifications
8.6 BIOS description
Advanced > Boot Configuration
System parameters
Numlock
POST errors
Default settings
On
All without keyboard
Local settings
Advanced > Peripheral Configuration
System parameters
Internal COM 1
Base I/O address
2
Interrupt
2
Internal COM 2
Base I/O address
2
Interrupt
2
Internal LPT
Default settings
Auto 1
3F8
IRQ4
Auto
1
2F8
IRQ3
Auto
1
Base I/O address
3
Interrupt
3
Mode
3
DMA Channel
3
Onboard PROFINET
1
PCI – MPI / DP
1
Audio
378
IRQ7
Bi-directional
DMA 1
Enabled
Enabled
Auto
Onboard Ethernet 1 (LAN 1, X1 P1)
Onboard Ethernet 2 (LAN 2, X2 P1)
Enabled
Enabled
1
2
3
Depending on the ordered device configuration
Only visible if the associated parameter "Internal COM #" is enabled.
Only visible if "Internal LPT 1" is enabled.
Local settings
Advanced > SATA Configuration
System parameters
SATA Controller
Default settings
Enabled
HDC Configure As AHCI
1
1
Depending on the ordered device configuration
Advanced > Fan Control Configuration
System parameters
Fan Control Mode
Default settings
Standard
1
Depending on the ordered device configuration
1
Local settings
Local settings
192
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical specifications
8.6 BIOS description
Advanced > Video Configuration
System parameters
Primary Display
IGD - Aperture Size
IGD - DVMT Size
IGD boot type
IGD boot type 2
PEG0 - Gen X
PEG1 - Gen X
PEG2 - Gen X
Advanced > Chipset Configuration
System parameters
VT-d
After G3 On
DeepSx Power Policies
Max TOLUD
HPET Support
Default settings
Auto
128 MB
MAX
VBIOS default
Disabled
Auto
Auto
Auto
Advanced > USB Configuration
System parameters
USB Precondition
XHCI
Per-Port Control
Default settings
Enabled
Auto
Disabled
Local settings
The following parameters are only visible if "Per-Port Control" is enabled (Enabled).
USB Port 0 (X61)
USB Port 1 (X60)
USB Port 2 (USB3 P2, internal)
USB Port 3 (USB3 P3, front)
USB Port 4 (X63)
USB Port 5 (X62)
USB Port 6 (USB2 P6, front )
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
USB Port 8 (USB2 P8, internal)
USB Port 9 (USB2 P9, internal)
USB Port 10 (USB2 P10, internal)
USB Port 11 (USB2 P11, internal)
Enabled
Enabled
Enabled
Enabled
Default settings
Auto
Last State
Disabled
3 GB
Enabled
Local settings
Local settings
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
193
Technical specifications
8.6 BIOS description
Advanced > Active Management Technology Support
System parameters
Intel AMT Support
Hide Un-Configure ME Confirmation
Un-Configure ME
Intel AMT Password Write
AMT CIRA Request Trig
USB Configure
AMT CIRA Timeout
Default settings
Enabled
Disabled
Disabled
Enabled
Disabled
Enabled
0
Local settings
Advanced > PCI Express Configuration
System parameters
PCI Express Root Port 5
PCIe Speed
2
PCI Express Root Port 6
1
PCIe Speed
1 2
PCI Express Root Port 7
1
Default settings
Enabled
Auto
Enabled
Auto
Enabled
Local settings
PCIe Speed
1 2
PCI Express Root Port 8
1
Auto
Enabled
PCIe Speed
1 2
Auto
1
2
Visible depending on the ordered device configuration
Only visible if the associated parameter "PCI Express Root Port #" is enabled.
Security
System parameters
TPM Status
1
TPM Operation
1
TPM Force Clear
1
Set Supervisor Password
Set User Password
Power-on Password
2
Default settings
Depending on configuration
No Operation
Disabled
Disabled
User Access Level
2
Option ROM keyboard
2
Full
Enabled
1
2
Visible depending on the ordered device configuration
Only visible if "Supervisor Password" is set.
Local settings
194
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical specifications
8.6 BIOS description
Power
System parameters
Wake on PME or LAN 2 (X2 P1)
Auto Wake on S5
Wake on S5 Time
1
Day of Month
1
Wake on LAN 1 (X1 P1)
PROFINET always On
2
Default settings Local settings
Disabled
Disabled
00:00:00
1
Enabled
Disabled
PROFINET Wake Capability 2 3
USB Ports 0/1 (X61/X60) powered
USB Ports 0/1 (X61/X60) Wake Capability
4
Disabled
Enabled
Disabled
USB Ports 4/5 (X63/X62) powered
USB Ports 4/5 (X63/X62) Wake
Capability
4
USB Ports 3/6/8/9 powered
Enabled
Disabled
USB Port 3/6/8/9 Wake Capability
4
Enabled
Disabled
1
2
Only visible if the "Auto Wake on S5" is set accordingly.
3
Visible depending on the ordered device configuration
4
Only visible if the parameter "PROFINET always On" is enabled.
Only visible if the associated parameter "USB Ports # powered" is enabled.
Power > Advanced CPU Control
System parameters
P-States (ACTUAL)
Active Processor Cores
HT Support
Execute Disable Bit
Intel (VMX) Virtualization Technology
C-States
Turbo Mode
Default settings Local settings
Enabled
All Cores
Auto
Enabled
Enabled
Enabled
Enabled
Boot
System parameters
Boot Type
Quick Boot
Quiet Boot
Network Stack
PXE Boot capability
Add Boot Options
USB Boot
EFI Device First
Boot Delay Time
Default settings Local settings
Dual Boot Type
Enabled
Enabled
Disabled
Disabled
Auto
Enabled
Enabled
3
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
195
Technical specifications
8.6 BIOS description
Boot > Legacy
System parameters
Normal Boot Menu
Boot Type Order
Floppy drive
Hard Disk Drive
CD/DVD ROM Drive
USB
Others
Exit
System parameters
Profile:
Default settings
Standard
In the order of the following
Boot media types:
Depending on configuration
Depending on configuration
Depending on configuration
Depending on configuration
Depending on configuration
Local settings
Default settings Local settings
8.6.7
8.6.7.1
Alarm, error and system messages
Power On Self Test
BIOS first performs a Power On Self Test (POST) within the boot routine to verify proper operation of certain functional units of the PC. The boot sequence is interrupted immediately if a fatal error is detected.
BIOS initializes and tests further functional units if the POST does not return any errors. In this startup phase, the graphics controller is initialized and any error messages are output to the screen.
The error messages output by system BIOS are listed below. For information on error messages output by the operating system or application programs, refer to the corresponding manuals.
196
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical specifications
8.6 BIOS description
On-screen error messages
On-screen error message
Error - Keyboard error
Error - Keyboard controller error or no keyboard present
Error - PCH softstrap can't be programmed, descriptor locked:
Riser card may not work correctly
Error - SPI regions are not locked (ME unlocked)
Meaning / tip
Check whether the keyboard is properly connected.
Check whether a functioning keyboard is properly connected. If this is the case, contact your technical support team.
Error - Keyboard controller error Keyboard error Contact your Technical Support.
Error - System halted - harddisk drive (HDD) locked!
Turn off device, remove, HDD interlock and reboot once again.
PROFIBUS interface defective Contact your Technical Support. Error - No MPI/DP interface detected
Error - PCH softstrap programming error: Riser card may not work correctly
Contact your Technical Support.
Contact your Technical Support.
Contact your Technical Support.
Error - Riser card Taufe does not match connected hardware configuration
Error - Taufe configuration not present (Platform = Unknown)
Warning - Manufacturer mode enabled
System RAM Failed at offset
Error - CMOS battery failed
Error - SMART failure detected on HDD
No bootable device -- Please restart system
Contact your Technical Support.
Contact your Technical Support.
Contact your Technical Support.
Memory error Contact your Technical Support.
Battery on the CPU module defective or empty Contact your
Technical Support.
Hard disk fault: A fault threshold specified by the manufacturer has been exceeded. Operation of the hard disk is unreliable. The hard disk has to be replaced. Contact your Technical Support.
Possible causes:
•
No operating system installed
• Wrong drive addressed (disk in drive A/B)
•
Incorrect active boot partition
• Incorrect drive entries in SETUP
•
HDD not connected / defective
Error - Realtime clock has lost power
Screen remains dark - cursor flashes at top left
Timer block error Contact your Technical Support.
A data carrier is inserted in the ODD drive. In this case it can take several minutes until the BIOS power up is continued.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
197
Technical specifications
8.6 BIOS description
8.6.7.2 BIOS beep codes
Below please find the customer-relevant POST codes. Contact Customer Support
( http://www.siemens.de/automation/csi_en_WW ) for information on all other POST codes.
Display
(hex)
01H
Meaning
SEC_SYSTEM_POWER_ON
Description Remedy
02H
03H
04H
05H
06H
07H
08H
09H
0AH
70H
71H
72H
73H
74H
75H
76H
77H
78H
79H
SEC_BEFORE_MICROCODE_PATCH
SEC_AFTER_MICROCODE_PATCH
SEC_ACCESS_CSR
SEC_GENERIC_MSRINIT
SEC_CPU_SPEEDCFG
SEC_SETUP_CAR_OK
SEC_FORCE_MAX_RATIO
SEC_GO_TO_SECSTARTUP
SEC_GO_TO_PEICORE
PEI_SIO_INIT
PEI_CPU_REG_INIT
PEI_CPU_AP_INIT
PEI_CPU_HT_RESET
PEI_PCIE_MMIO_INIT
PEI_NB_REG_INIT
PEI_SB_REG_INIT
PEI_PCIE_TRAINING
PEI_TPM_INIT
PEI_SMBUS_INIT
CPU power on and switch to Protected mode
Patching CPU microcode
PCIE MMIO Base
Address initial
Switch to Protected
Mode
Load CPU Microcode
Setup Cache as RAM Set up cache as
RAM
Initialize PCIE
CPU Generic MSR initial
Setup CPU speed
Cache as RAM test
Tune CPU frequency ratio to maximum level
Setup BIOS ROM cache
Enter Boot Firmware
Volume
Super I/O initial
Service case
Service case
Service case
Service case
Initialize CPU MS
(Machine Status)
Register
Calling up the boot firmware memory area
Initialization of the
Super I/O
Service case
Specify CPU speed Service case
Carry out RAM
Test on cache
Replacing a basic module
Service case Setting CPU frequency
Set up BIOS ROM cache
Service case
Service case
Service case
CPU Early Initial
Multi-processor Early initial
Initialize CPU Register
Multi processor initialization
HyperTransport initial Initialize Hyper
Transport functionality
PCIE MMIO BAR
Initial
North Bridge Early
Initial
South Bridge Early
Initial
PCIE Training
TPM initial
SMBUS Early Initial
Initialize PCIE
Register
Initialization of the
North bridge
Initialization of the
South bridge
Service case
Service case
Service case
Service case
Service case
Service case
Training phase of the PCIE device
Service case
TPM initialization Service case
Initialization of the
SM Bus
Service case
198
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Display
(hex)
7AH
Meaning
PEI_PROGRAM_CLOCK_GEN
7BH PEI_IGD_EARLY_INITIAL
7CH PEI_HECI_INIT
7DH
7EH
PEI_WATCHDOG_INIT
PEI_MEMORY_INIT
7FH PEI_MEMORY_INIT_FOR_CRISIS
80H PEI_MEMORY_INSTALL
81H PEI_TXTPEI
82H
83H
84H
85H
86H
PEI_SWITCH_STACK
PEI_MEMORY_CALLBACK
PEI_ENTER_RECOVERY_MODE
PEI_RECOVERY_MEDIA_FOUND
PEI_RECOVERY_MEDIA_NOT_FOUND
87H PEI_RECOVERY_LOAD_FILE_DONE
88H PEI_RECOVERY_START_FLASH
89H PEI_ENTER_DXEIPL
Technical specifications
8.6 BIOS description
Description Remedy
Clock Generator Initial Initializations of the clock generator
Internal Graphic device early initial,
PEI_IGDOpRegion
First initialization of the graphic connection
HECI Initial
Simple Memory test
Initialization of the
Host Embedded
Controller
Interface
Watchdog timer initial Initialization of the watchdog timer
Memory Initial for
Normal boot
Memory initialization during the PEI phase
Memory Initial for
Crisis Recovery
Memory initialization for BIOS recovery
Memory test
Service case
Service case
Service case
Service case
Replace the memory modules
Replace the memory modules
Replace the memory modules
Service case TXT function early initial
Initialization of the
Trusted Execution
Technology
Start to use Memory Start the memory use
Set cache for physical memory
Use cache as a physical memory
Recovery device initial Initialize the device for BIOS recovery
Found Recovery image
BIOS Recovery image found
Recovery image not found
BIOS Recovery image not found
Service case
Service case
Service case
Service case
Check whether the BIOS
Recovery image exists on the
Recovery medium (e.g.
USB stick).
Service case Load Recovery Image complete
Start Flash BIOS with
Recovery image
Loading BIOS image to RAM
Loading of BIOS
Recovery image completed
Starting of flashing of BIOS Recovery image
Copy BIOS image to the RAM
Service case
Service case
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
199
Technical specifications
8.6 BIOS description
Display
(hex)
8AH
Meaning
PEI_FINDING_DXE_CORE
8BH
40H
41H
PEI_GO_TO_DXE_CORE
DXE_TCGDXE
DXE_SB_SPI_INIT
42H
43H
DXE_CF9_RESET
DXE_SB_SERIAL_GPIO_INIT
44H
45H
46H
47H
DXE_SMMACCESS
DXE_NB_INIT
DXE_SIO_INIT
DXE_LEGACY_REGION
48H
49H
4AH
4BH
4CH
DXE_SB_INIT
DXE_IDENTIFY_FLASH_DEVICE
DXE_FTW_INIT
DXE_VARIABLE_INIT
DXE_VARIABLE_INIT_FAIL
4DH
4EH
4FH
50H
51H
52H
DXE_MTC_INIT
DXE_CPU_INIT
DXE_MP_CPU_INIT
DXE_SMBUS_INIT
DXE_SMART_TIMER_INIT
DXE_PCRTC_INIT
200
Description Remedy
Loading DXE core
Enter DXE core
TPM initial in DXE
Loading DXE
(Driver
Execution Environment) program
Service case
Start DXE program Service case
TPM initialization in
DXE phase
Service case
Service case South bridge SPI initial Initialization of the
Serial Peripheral
Interface in the
South Bridge
Setup Reset service,
DXE_CF9Reset
South bridge Serial
GPIO initial,
DXE_SB_SerialGPIO_I
NIT
Setup Reset service
Initializations of the serial GPIO
Setup SMM ACCESS service
North bridge Middle initial
Setup SMM access service
Initialization of the
North Bridge
Service case
Service case
Service case
Service case
Super I/O DXE initial Initialization of the
Super IO
Setup Legacy Region service,
DXE_LegacyRegion
Setup service Legacy region
South Bridge Middle
Initial
Initialization of the
South Bridge
Identify Flash device Identify FLASH type
Service case
Service case
Service case
Service case
Fault Tolerant Write verification
Checking of the write fault tolerance
Variable Service Initial Initialization of the variable service
Fail to initial Variable
Service
Failure to initialize the variable service
Service case
Service case
Service case
MTC Initial
CPU Middle Initial
Multi-processor Middle
Initial
MonoTonicCounter initialization
Service case
CPU initialization Replacing a basic module
Multiprocessor initialization
SMBUS Driver Initial SMBUS driver initialization
8259 Initial SMART Timer initialization
Replacing a basic module
Service case
Service case
RTC Initial RTC initialization Service case
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Display
(hex)
53H
Meaning
DXE_SATA_INIT
54H DXE_SMM_CONTROLER_INIT
55H DXE_LEGACY_INTERRUPT
56H
57H
58H
59H
5AH
5BH
5CH
DXE_RELOCATE_SMBASE
DXE_FIRST_SMI
DXE_VTD_INIT
DXE_BEFORE_CSM16_INIT
DXE_AFTER_CSM16_INIT
DXE_LOAD_ACPI_TABLE
DXE_SB_DISPATCH
5DH DXE_SB_IOTRAP_INIT
5EH DXE_SUBCLASS_DRIVER
5FH DXE_PPM_INIT
60H DXE_HECIDRV_INIT
61H DXE_VARIABLE_RECLAIM
10H
11H
12H
BDS_ENTER_BDS
BDS_INSTALL_HOTKEY
BDS_ASF_INIT
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical specifications
8.6 BIOS description
Description Remedy
SATA Controller early initial
Setup SMM Control service,
DXE_SMMControler_I
NIT
Setup Legacy Interrupt service,
DXE_LegacyInterrupt
Advance initialization of the SATA
Controller
SSM Control service
Setup Legacy
Interrupt service
Relocate SMM BASE Reassign SMM base
SMI test
VTD Initial
Legacy BIOS initial
Legacy interrupt function initial
ACPI Table Initial
SMI test
Initialize I/O virtualization (VTD)
Legacy BIOS initialization
Legacy interrupts initialization
Setup SB SMM Dispatcher service,
DXE_SB_Dispatch
Setup SB IOTRAP
Service
ACPI table initialization
SMM dispatcher service
Build AMT Table
PPM Initial
SouthBridge
IOTRAP service
Initialization of the
AMT (Active Management
Technology) table
Initialization of the
Processor Power
Management
HECIDRV Initial
Variable store garbage collection and reclaim operation
Enter BDS entry
Initialization of the
Host Embedded
Controller
Interface
Loading of the variable memory
Phase Boot Device
Selection
Install Hotkey service Installation of the
Hotkey service
ASF Initial Initialize Alert
Standard Format
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
201
Technical specifications
8.6 BIOS description
Display
(hex)
13H
14H
202
Meaning
BDS_PCI_ENUMERATION_START
BDS_BEFORE_PCIIO_INSTALL
15H
16H
BDS_PCI_ENUMERATION_END
BDS_CONNECT_CONSOLE_IN
22H
23H
24H
25H
26H
1DH
1EH
1FH
20H
21H
17H
18H
19H
1AH
1BH
1CH
BDS_CONNECT_CONSOLE_OUT
BDS_CONNECT_STD_ERR
BDS_CONNECT_USB_HC
BDS_CONNECT_USB_BUS
BDS_CONNECT_USB_DEVICE
BDS_NO_CONSOLE_ACTION
BDS_DISPLAY_LOGO_SYSTEM_INFO
BDS_START_IDE_CONTROLLER
BDS_START_SATA_CONTROLLER
BDS_START_ISA_ACPI_CONTROLLER
BDS_START_ISA_BUS
BDS_START_ISA_FDD
BDS_START_ISA_SERIAL
BDS_START_IDE_BUS
BDS_START_AHCI_BUS
BDS_CONNECT_LEGACY_ROM
Description Remedy
PCI enumeration
PCI resource assign complete
Enumerate PCI bus
Assign PCI resources
PCI enumeration complete
Keyboard Controller,
Keyboard and Mouse initial
Video device initial
PCI enumeration completed
Initialization of keyboard and mouse
Error report device initial
USB host controller initial
Initialize graphic connection
Initialize default error output
Initialize USB host controller
USB BUS driver initial Initialize USB bus driver
USB device driver initial
Initialize USB device driver
Console device initial fail
Initialization of the console faulty
Display logo or system information
IDE controller initial
Display logo or system information
Initialization of the
IDE controller
SATA controller initial Initialization of the
SATA controller
SIO controller initial Initialization of the
Super IO
ISA BUS driver initial Initialization of the
ISA bus driver
Floppy device initial
Serial device initial
Initialization of the floppy connection
Initialization of the serial connection
IDE device initial Initialization of the
IDE connection
AHCI device initial Initialization of the
AHCI connection
Dispatch option ROMs Callup of the Legacy Option ROMs
Service case
Run a test by disabling the hardware components in
SETUP, or by removing the expansion cards installed on the bus board.
Service case
Run a test by replacing the keyboard/mouse
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical specifications
8.6 BIOS description
Display
(hex)
27H
28H
29H
2AH
2BH
2CH
2DH
2EH
2FH
30H
31H
32H
33H
34H
35H
F9H
FBH
FDH
FEH
Meaning
BDS_ENUMERATE_ALL_BOOT_OPTION
BDS_END_OF_BOOT_SELECTION
BDS_ENTER_SETUP
BDS_ENTER_BOOT_MANAGER
BDS_BOOT_DEVICE_SELECT
BDS_ACPI_S3SAVE
BDS_READY_TO_BOOT_EVENT
BDS_GO_LEGACY_BOOT
BDS_GO_UEFI_BOOT
BDS_LEGACY16_PREPARE_TO_BOOT
BDS_EXIT_BOOT_SERVICES
BDS_LEGACY_BOOT_EVENT
BDS_ENTER_LEGACY_16_BOOT
BDS_RECOVERY_START_FLASH
POST_BDS_NO_BOOT_DEVICE
POST_BDS_START_IMAGE
POST_BDS_ENTER_INT19
P0ST_BDS_JUMP_BOOT_SECTOR
Description
Get boot device information
Determine the Boot
Device information
End of boot selection Boot selection terminated
BDS_EFI64_SHADOW_ALL_LEGACY_ROM Shadow Misc Option
ROM
Remedy
Enter Setup Menu
Enter Boot manager
Callup into SETUP Service case
Callup Boot Manager
Service case
Try to boot system to
OS
Booting of the OS Service case
Save S3 resume required data in RAM
Last Chipset initial before boot to OS
Copying the Legacy Option ROMs into RAM
Make available for operating state S3
RAM
Initialization of the last chipset before the
OS Boot
Start to boot Legacy
OS
Boot Legacy OS
Start to boot UEFI OS Boot UEFI OS
Prepare to Boot to
Legacy OS
Send END of POST
Message to ME via
HECI
Last Chipset initial before boot to Legacy
OS.
Ready to Boot Legacy
OS.
Fast recovery start flash
Preparation for booting of Legacy
OS
Terminate Boot
Service
Initialization of the last chipset before the
Legacy OS Boot
Callup to boot the
Legacy OS
Start the BIOS
Recovery function
No Boot Device, Post-
BDS_NO_BOOT_DEVI
CE
UEFI Boot Start Image,
Post-
BDS_START_IMAGE
No BOOT device found
Booting of an UEFI image
Legacy 16 boot entry Start Legacy 16 boot
Try to Boot with INT 19 Boot with INT 19
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
Service case
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
203
Technical specifications
8.7 Active Management Technology (AMT)
Display
(hex)
E4H
Meaning
ASL_WAKEUP_S4
E5H ASL_WAKEUP_S5
Description Remedy
System wakeup from
S4
System wakeup from
S5
Reboot from operating state S4
Reboot from operating state S5
Service case
Service case
Note
If the boot process is interrupted with a BIOS POST message output on the screen, you will hear three long beeps. The parameter "POST Errors" must, for example, be set to "Halt on all errors" in the BIOS setup menu "Advanced > Boot Configuration" for this.
Special codes
Only the following BIOS post message is output as beep code:
● No RAM: 3 long beeps followed by 2 short beeps, repeated for a total of three times.
8.7
8.7.1
Active Management Technology (AMT)
AMT basics
The Intel Core and Xeon processors support Intel® vPro
Technology at the hardware end.
TM
and Intel Active Management
An administrator at the Help Desk PC accesses the AMT
PCs. Only the AMT PCs must have an integrated Intel AMT.
The following figure shows the possible structure of a network for remote management on the basis of SIMATIC AMT-PCs.
204
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical specifications
8.7 Active Management Technology (AMT)
From a SIMATIC IPC which does not have Intel AMT functions, you can access networked
SIMATIC IPCs with Intel AMT using the SIMATIC IPC Remote Manager and/or a web browser.
SIMATIC IPCs that support AMT feature two onboard Ethernet interfaces, each with a separate controller. The controller integrated in the chipset of the type: "xxxxxxLM" can be configured for the use of Intel AMT. Further details about the controller can be found in the technical specification.
For security reasons, AMT is disabled when you receive a SIMATIC IPC. Enable AMT in the
BIOS setup. Afterwards the Intel® Management Engine (Intel® ME) has to be activated and set for AMT. You make additional settings in the Management Engine:
● Configuring the network for access via AMT
● Creating a password
8.7.2 Overview of AMT
This section describes the required measures and settings on the local IPC so that the IPC can be controlled and maintained remotely from a management station known below as the help desk PC.
The local IPC is known below as the "AMT PC".
The sections contain the following information:
● AMT settings in the MEBx and in the BIOS setup
● Basic configuration of AMT
● Further useful notes
8.7.3
Procedure
Enabling AMT, basic configuration
1. Connect the AMT PC with the LAN.
2. If necessary, first reset AMT to the default status (see section "Unconfigure").
3. Reboot the device.
To open the BIOS selection menu, press the <ESC> key during the following BIOS message:
Press Esc for Boot Options
4. Use the "SCU" (Setup Configuration Utility) button to open the BIOS setup.
5. In the "Advanced" menu, "Active Management Technology Support" submenu check to make sure that "Intel AMT Support" is enabled.
6. Exit the BIOS setup with <F10> key "Save and Exit". The AMT PC restarts.
7. To open the BIOS selection menu, press the <ESC> key.
8. Click the "MEBx" button.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
205
Technical specifications
8.7 Active Management Technology (AMT)
9. In the login dialog, enter the standard password "admin".
10. Change the default password. The new password must include the following characters:
– In total at least eight characters
– One upper case letter
– One lower case letter
– One number
– One of the special characters ! @ # $ % ^ & * @ # $ % ^ & *
Note
The underscore _ and the space characters are valid password characters, however they do not increase password complexity.
11. Enable "Intel (R) AMT Configuration > Manageability Feature Selection".
12. Enable "Intel (R) AMT Configuration > Activate Network Access".
8.7.4 Advanced settings
The BIOS and the MEBx contain the most important basic settings for AMT. Additional tools are necessary if you want to make more advanced settings. If required, these must be downloaded from the relevant manufacturer's site. For information on the options and use of these tools, refer to the relevant documentation of the manufacturer.
● Manageability Commander and other tools of the Intel DTK (Manageability Developer
Tool Kit): Programs from the Intel DTK that you can download from the Internet at
"http://software.intel.com/en-us/manageability".
● AMT Web interface: For encrypted connections, the URL of the Web interface is "https://
<Fully qualified domain name>:16993" and for unencrypted connections "http://<IP address>:16992".
● WinRM: A command line program that is part of Windows as of Windows Vista. This tool can be downloaded for older Windows versions.
206
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
8.7.5
Technical specifications
8.7 Active Management Technology (AMT)
Resetting with Unconfigure
Note
If the AMT PC still has its factory settings, for example has just been purchased, you can skip this section.
If you have already configured AMT previously, it is best to discard all the previous AMT settings made in the MEBx.
Note
All previous settings in the management engine are deleted.
Correct operation in the plant may be at risk.
Note down all the settings in the MEBx. Make the settings again as necessary following
Unconfigure.
1. Enable the "Unconfigure ME" entry in "Advanced > Active Management Technology
Support" in the BIOS.
2. Exit the BIOS with the <F10> key "Save and Exit". The AMT PC restarts.
3. After the restart, a user prompt appears asking whether you really want to discard all the settings in the management engine:
4. Confirm with "Y". On a German keyboard, this means pressing the <Z> key.
The device continues to boot with the factory settings of the management engine.
8.7.6 Determining the network address
To connect the AMT PC with the AMT server, the network address that uniquely localizes the AMT server on the AMT PC must be entered.
If DHCP is set for the automatic assignment of the network address in "Network Setup" in the MEBx of the AMT PC, the network address is not fixed.
Procedure
If the AMT server uses the same network address as the operating system of the AMT PC
(most common situation):
1. You can obtain the address of the AMT server in the command line in Windows using
"ipconfig" and in UNIX using "ifconfig".
If the AMT server and operating system do not use the same network address, ask your network administrator for the address you have been assigned.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
207
Technical specifications
8.8 Assignment of expansion interface to the software in the TIA Portal (CP assignment)
8.7.7 Forcing user consent
When establishing a connection to the AMT PC, the KVM viewer may prompt the user to enter a six-figure code. This code is displayed on the screen of the AMT PC. The user of the
AMT PC must inform the user of the KVM viewer of this code.
This code query needs to be set up on the KVM viewer.
Procedure
1. Select "Intel(R) AMT Configuration > User Consent" in the MEBx.
2. Select the value "KVM" for "User Consent".
To allow a user with administrator privileges to avoid this code query, follow these steps:
1. Select "Intel(R) AMT Configuration > User Consent" in the MEBx.
2. Enable "Opt-in configurable from remote IT".
8.8 Assignment of expansion interface to the software in the TIA Portal
(CP assignment)
The table below shows the correlation between enclosure labeling of the IPC expansion slots and the labeling that is used during assignment of interfaces to the software in the TIA
Portal.
3
4
Enclosure labeling
1
2
TIA Portal
X100
X101
X102
X103
208
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical support
A
A.1 Service and support
You can find additional information and support for the products described on the Internet at the following addresses:
● Technical support ( http://www.siemens.de/automation/csi_en_WW )
● Support request form ( http://www.siemens.com/automation/support-request )
● After Sales Information System SIMATIC IPC/PG ( http://www.siemens.com/asis )
● SIMATIC Documentation Collection ( http://www.siemens.com/simatic-tech-doku-portal )
● Your local representative
( http://www.automation.siemens.com/mcms/aspa-db/en/Pages/default.aspx
)
● Training center ( http://sitrain.automation.siemens.com/sitrainworld/?AppLang=en )
● Industry Mall ( https://mall.industry.siemens.com
)
When contacting your local representative or Technical Support, please have the following information at hand:
● MLFB of the device
● BIOS version for industrial PC or image version of the device
● Other installed hardware
● Other installed software
Tools & downloads
Please check regularly if updates and hotfixes are available for download to your device. The download area is available on the Internet at the following link:
After Sales Information System SIMATIC IPC/PG ( http://www.siemens.com/asis )
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
209
Technical support
A.2 Troubleshooting
A.2
Problem
The device is not operational
Troubleshooting
This section provides you with tips on how to locate and/or troubleshoot problems which occur.
Possible cause
No power supply
Possible remedy
• Check the power supply, the network cable and the power plug.
•
Check if the On/Off switch is in the correct position.
Device is being operated outside the specified ambient conditions
•
Check the ambient conditions.
•
After transport in cold weather, wait approximately 12 hours before switching on the device.
The monitor remains dark The monitor is switched off. Switch on the monitor.
The monitor is in "power save" mode Press any key on the keyboard.
The brightness button has been set to dark
Increase brightness using the brightness button. For detailed information, refer to the monitor operating instructions.
The power cord or the monitor cable is not connected.
•
Check whether the power cord has been properly connected to the monitor and to the system unit or to the grounded shockproof outlet.
• Check whether the monitor cable has been properly connected to the system unit and to the monitor.
The mouse pointer does not appear on the screen
The mouse driver is not loaded
Mouse not connected.
If the monitor screen still remains dark after you have performed these checks and measures, contact your technical support team.
Check whether the mouse driver is properly installed and available when you start the user program.
Detailed information about the mouse driver is available in the corresponding documentation.
•
Check whether the mouse cord is properly connected to the system unit.
• If you use an adapter or extension for the mouse cable, also check these connectors.
Wrong time and/or date on the PC
If the mouse pointer still does not appear on the screen after you have performed these checks and actions, contact your technical support team.
1. Press <ESC> during the booting process to open the BIOS Setup.
2. Set the time and date in the setup menu.
Although the BIOS setting is
OK, the time and data are still wrong.
The backup battery is dead. Replace the backup battery.
USB device not responding. The USB ports are disabled in BIOS. Use a different USB port or enable the port.
210
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical support
A.2 Troubleshooting
Problem
DVD/CD drive door, if present, does not open
The screen flickers when the mouse moves or when programs are called
The startup of a Windows operating system on a GPT data carrier is aborted with the following error message:
"Status: 0xc0000225 Info:
The boot selection failed because a required device is inaccessible"
Possible cause
USB 2.0 device connected and
USB 2.0 is disabled.
The operating system does not support the USB ports.
The device is switched off or the open/close button is disabled by a software application.
DDC information is not available.
Possible causes:
•
•
Monitor does not supply DDC information
KVM switch does not forward
DDC information
•
Y cable adapter with DVI-I for
DVI-D/VGA connector is being used
The boot parameters in the boot loader file "BCD" are incorrect or damaged.
Possible remedy
Enable USB 2.0.
• Turn on USB Legacy Support for mouse and keyboard.
•
For other devices, you need the USB device drivers for the required operating system.
Emergency removal of the data medium:
1. Switch off the device
2. Insert a pointed object, for example, an opened paper clip, into the emergency extraction opening of the drive. Apply pressure carefully until the door opens.
3. Pull the door out further with your hand.
• Use a monitor that supports DDC
•
Use a KVM switch that forwards DDC information
• Use a simple cable adapter with only one interface
Run "Startup and Repair" from Microsoft Windows:
1. Insert the Recovery DVD into the optical drive.
2. Start the boot manager using the <F12> key during booting
3. Select the line with "UEFI" in front of the name of the optical drive
4. Click "Next" in the language selection window
5. In the following "Install Windows" dialog, click on
"Repair your computer" or press the <R> key.
The "System Recovery Options" dialog appears.
The system is checked for errors.
6. Next, click "Repair and restart"
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
211
Technical support
A.3 Troubleshooting status indicators
Error displays on the front panel
Front LED
Red WATCHDOG LED is lit
Red TEMP LED is lit
Red FAN LED is lit
Red HDD0 ALARM LED is lit
Red HDD1 ALARM LED is lit
Red HDD2 ALARM LED is lit
HDD | HDD3 ALARM is lit in red or flashes green
HDD0, HDD1, HDD2 ALARM and
HDD | HDD3 ALARM flash red
HDD0, HDD1, HDD2 ALARM and
HDD | HDD3 ALARM is lit in red
Possible cause
Watchdog has triggered
Excess temperature in the device
Details about the error display
See section "Watchdog (WD)"
See section "Temperature monitoring/display"
Fan failure See section "Fan monitoring"
RAID reports that hard disk 0 is defective See section "Status displays"
RAID reports that hard disk 1 is defective See section "Status displays"
RAID reports that hard disk 2 is defective See section "Status displays"
RAID reports that hard disk 3 is defective See section "Status displays"
RAID is in the "rebuild" state
RAID system is not ready for operation:
See section "Status displays"
PN Ι MPI/DP lights up red
All front-panel LEDs are constantly lit
A fault has occurred on the CPU 1616 onboard interface
Error in early BIOS-POST
Affected drive must be identified with the help of the RAID software. See section
"Expanding and assigning parameters to the device", section "Drives" and section "Managing RAID systems".
See section "Status displays"
Contact Technical Support.
A.3 Troubleshooting status indicators
Error displays on the front panel
Front LED Possible cause Details about the error display
HDD0 ALARM LED lights up red RAID signals that hard disk 0 is defective See section "Maintaining and repairing the
HDD1 ALARM LED lights up red RAID signals that hard disk 1 is defective
HDD2 ALARM LED lights up red RAID signals that hard disk 2 is defective device" in the Operating Instructions for the IPC.
HDD3 ALARM lights up red
HDD0, HDD1, HDD2, and HDD3
ALARM LEDs flash red
RAID signals that hard disk 3 is defective
RAID is in the "rebuild" state
HDD0, HDD1, HDD2, and HDD3
ALARM LEDs light up red
PN Ι MPI/DP lights up red
All front-panel LEDs are constantly lit
RAID system is not ready for operation:
A fault has occurred on the CPU 1616 onboard interface
Error in early BIOS-POST
The affected drive must be identified using the RAID software.
See section "Maintaining and repairing the device" in the Operating Instructions for the IPC.
See section "Communication Processor
CP 1616 onboard" in the Operating Instructions for the IPC.
Contact Technical Support.
212
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical support
A.4 RAID system and device startup
Redundant power supply
Problem
Device failure despite redundant power supply in case of power failure
Possible cause
• One module is not switched on
•
Both modules are connected so the same AC circuit
Possible remedy
• Switch on both modules
•
Connect modules to separate AC circuits
A.4 RAID system and device startup
Problem
The RAID software reports the following errors:
•
The RAID plug-in failed to load, because the drive is not installed.
• The Serial ATA plug-in failed to load, because the driver is not installed correctly.
•
The Intel
®
Matrix Storage Console was unable to load a page for the following reason:
– A plug-in did not provide a page for the selected device
– A plug-in failed to load
After changing the drive, the system does not boot from the RAID system
Cause
RAID is not activated
RAID is activated
RAID system does not have highest boot priority
After changing the drive, "unused" is indicated for the relevant SATA port
Computer does not boot or "Boot device not found" is displayed
Remedy
The messages have no negative effect on the operation of the device and can be ignored.
Acknowledge the messages.
Install the software again from the supplied
"Documentation and Drivers" DVD.
BIOS setup, Boot menu:
• Permit RAID system in the boot priority
•
Set the RAID system to be first in the boot priority order.
Reboot the system with a functioning drive. System was booted without functioning drive. The removable drive bay might not be switched on.
•
The boot device is not permitted
•
The boot device is not in first place of the boot priority in the BIOS setup
•
The boot data carrier is set up with GPT and UEFI boot is deactivated in the BIOS setup
• In the BIOS setup "Boot" menu, permit the boot device in the boot priority
•
In the BIOS setup "Boot" menu, change the boot priority of the Boot device
• Activate UEFI boot in the BIOS setup.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
213
Technical support
A.4 RAID system and device startup
Problem
The startup of a Windows operating system on a GPT data carrier is aborted with the following error message:
"Status: 0xc0000225 Info: The boot selection faild because a required device is inaccessible"
Cause
The boot parameters in the boot loader file "BCD" are incorrect or damaged.
Remedy
Execute "Startup and Repair" from Microsoft
Windows:
1. Insert the Recovery DVD into the optical drive.
2. Select the line with "UEFI" in front of the name of the optical drive.
3. Click "Next" in the language selection window.
4. In the following "Install Windows" dialog, click on "Repair your computer" or press the <R> key. The "System
Recovery Options" dialog appears. The system is checked for errors.
5. Next, click "Repair and restart".
Problem
After changing the hard disk, the system does not boot from the RAID system
Computer does not boot or "Boot device not found" is displayed
RAID software cannot be started
RAID software displays no details of the RAID system
Monitoring software signals implausible states
Adaptec Storage Manager software cannot be started
Possible cause
RAID system does not have highest boot priority
Possible remedy
BIOS setup, boot menu:
• Permit RAID system in the boot priority
•
Set the RAID system to be first in the boot priority order.
•
The boot device is not permitted
• The boot device is not in first place of the boot priority in the BIOS setup
•
The boot data carrier is set up with GPT and UEFI boot is deactivated in the BIOS setup
•
In the BIOS setup, "Boot" menu, permit the boot device in the boot priority
• In the BIOS setup, "Boot" menu, change the boot priority of the boot device
•
Activate UEFI boot in the BIOS setup.
• No Windows password
•
The Windows password was set up subsequently
• Main memory capacity
< 4 GB
• No Windows password
•
The Windows password was set up subsequently
Sampling rate of the SIMATIC monitoring software not reduced
Certificate error
• Uninstall and then reinstall RAID software
• Increase main memory capacity to at least
4 GB.
• Uninstall and then reinstall RAID application
Increase "RaidUpdateFactor" via registry key.
For details see section "Installation of Hardware RAID Controller Software".
Change address in the link to the Adaptec
Storage Manager software to "localhost".
Requirement: The certificate is stored in the
"Trusted Root Certification Authorities" certificate store and is not expired.
214
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Technical support
A.5 Notes on the use of third-party modules
A.5
Problem
The PC crashes during startup.
Notes on the use of third-party modules
Possible cause
• I/O addresses are assigned twice.
•
Hardware interrupts and/or
DMA channels are assigned twice
• Signal frequencies or signal levels are not adhered to
•
Different connector pin assignments
PCIe Gen1 expansion card does not behave according to specification.
Possible remedy
Check your computer configuration:
• If the computer configuration corresponds with factory state, please contact your technical support team.
•
If the computer configuration has changed, restore the original factory settings. Remove all third-party expansion cards, then restart the PC. If the error no longer occurs, the third-party expansion card was the cause of the fault.
Replace this expansion card with a Siemens card or contact the card supplier.
If the PC still crashes, contact your technical support team.
1. Remove the expansion card.
2. Set the respective setup parameter "PCIe Speed" permanently to "Gen1" in the "Advanced > PCI Express
Configuration" menu, submenu "PCI Express Root Port #" of the BIOS Setup.
3. Set the respective setup parameter "PEG# - Gen X" permanently to "Gen1" in the "Advanced > Video
Configuration" menu, submenu "Pci Expess Graphic" of the
BIOS Setup.
4. Install the expansion card again.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
215
Technical support
A.5 Notes on the use of third-party modules
216
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Abbreviations
Abbreviation Term
AC Alternating current
ACPI
PLC
AGP
AHCI
Advanced Configuration and Power
Interface
Programmable controller
Accelerated Graphics Port
Advanced Host Controller Interface
AMT
APIC
APM
CF
CGA
CIRA
CLK
CMOS
COA
CoL
COM
CP
CPU
AS
ASIS
AT
ATA
ATX
AWG
BIOS
CAN
CD-ROM
CD-RW
CE
Active Management Technology
Advanced Programmable Interrupt
Controller
Advanced Power Management
Automation system
After Sales Information System
Advanced Technology
Advanced Technology Attachment
AT-Bus-Extended
American Wire Gauge
Basic Input Output System
Controller Area Network
Compact Disc – Read Only Memory
Compact Disc – Rewritable
Communauté Européenne (CE symbol)
Compact Flash
Color Graphics Adapter
Client Initiated Remote Access
Clock pulse
Complementary Metal Oxide
Semiconductors
Certificate of authentication
Certificate of License
Communications Port
Communication Processor
Central Processing Unit
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
B
Meaning
Alternating current
High speed bus system
Standardized controller interface for SATA devices. This is supported in Microsoft Windows XP as of SP1 and IAA driver.
Remote maintenance technology from Intel
Extended programmable interrupt controller
Tool for monitoring and reducing power consumption of the
PC
US standard for the cable diameter
Basic Input Output System
Removable storage medium for large data volumes
Rewritable CD
The product is in conformance with all applicable EC directives
Standard monitor interface
Administration of AMT PCs not in the intranet
Clock signal for controllers
Complementary metal oxide semiconductors
Microsoft Windows Product Key
License authorization
Term for the serial interface
Communication computer
CPU
217
Abbreviations
EPP
ESC
EWF
FAQ
FAT 32
FBWF
FD
FQDN
CTS
DRAM
DC
DCD
DDRAM
DHCP
DMA
DOS
DP
DQS
DSR
DTK
DTR
DVD
DVI
DVI-I
ECC
ECP
EFI
EGA
ESD
Abbreviation Term
CRT
CSA
DM
EIDE
EISA
EMM
EM64T
EN
EPROM /
EEPROM
Cathode Ray Tube
Canadian Standards Association
Clear To Send
Dynamic Random Access Memory
Direct Current
Data Carrier Detect
Double Data Random Access Memory
Dynamic Host Configuration Protocol
Direct Memory Access
Disk Operating System
Display Port
Deutsche Gesellschaft zur Zertifizierung von
Qualitätsmanagement mBH
Data Set Ready
Developer Tool Kit
Data Terminal Ready
Digital Versatile Disk
Digital Visual Interface
Digital Visual Interface
Error checking and correction
Extended capability port
Extensible Firmware Interface
Enhanced Graphics Adapter
Components sensitive to electrostatic charge
Electronic Manual
Enhanced Integrated Drive Electronics
Extended Industry Standard Architecture
Expanded Memory Manager
Extended Memory 64 technology
European standard
Erasable Programmable Read-Only Memory
/ Electrically Erasable Programmable
Read-Only Memory
Enhanced Parallel Port
Escape character
Enhanced Write Filter
Frequently Asked Questions
File Allocation Table 32-bit
File-Based Write Filter
Floppy disk
Fully qualified domain name
Meaning
Canadian organization for tests and certifications according to own or binational standards (with UL / USA) standards
Clear to send
DC current
Data carrier signal detection
Memory chip with high-speed interface
Protocol for configuring IP networks
Direct memory access
Operating system without GUI
New powerful digital monitor port
Ready for operation
Tools for software development, testing, configuration etc.
Data terminal is ready
Digital versatile disk
Digital display interface
Digital display interface with digital and VGA signals
Error correction code
Extended parallel port
PC to monitor interface
An enhancement of the IDE standard
Extended ISA standard
Manages memory expansions
Plug-in submodules with EPROM/EEPROM chips
Bi-directional Centronics interface
Control character
FAQs
32-bit file allocation table
Disk drive, 3.5"
Full name of a domain
218
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Abbreviations
KVM
L2C
LAN
LCD
LED
LPT
LVDS
LW
MAC
MC
ME
MEBx
MLC
IGD
IP
IR
IRDA
IRQ
ISA
ITE
Hardware
I/O
IAA
IAMT
IDE
IDER
IEC
Abbreviation Term
FSB Front Side Bus
GND Ground
GPT
HD
HDA
HDD
Globally Unique Identifier Partition Table
Hard disk
High Definition Audio
Hard Disk Drive
HU
HMI
HORM
HT
HTML
HTTP
Height unit
Human Machine Interface
Hibernate Once - Resume Many
Hyper-Threading
Hyper Text Markup Language
Hypertext Transfer Protocol
Hardware
Input/Output
Intel Application Accelerator
Intel Active Management Technology
Integrated Device Electronics
IDE Redirection
International Electronical Commission
Integrated Graphics Device
Ingress Protection
Infrared
Infrared Data Association
Interrupt Request
Industry Standard Architecture
Information Technology Equipment
Keyboard, Video, Mouse
Level 2 cache
Local Area Network
Liquid Crystal Display
Light Emitting Diode
Line Printer
Low Voltage Differential Signaling
Drive
Media access control
Memory card
Management engine
Management Engine BIOS Extension multi-level cell
MLFB
MMC
Machine-readable product designation
Micro Memory Card
Meaning
Chassis ground
Hard disk
Hard disk drive
User interface
Script language for creating Internet pages.
Protocol for data transfer on the Internet
Data input/output on computers
Diagnostics, management and remote control of PCs
Remotely mounting an ISO file as a drive
Degree of protection
Infrared
Standard for data transfer via IR module
Interrupt request
Bus for expansion cards
Computer network that is limited to a local area.
Liquid crystal display
Light emitting diode
Printer port
Media access control
Memory card in credit card format
Unit implemented by AMT
User interface for basic configuration of AMT
Memory cells in which generally more than one bit per cell are saved
Memory card of the format 32 mm x 24.5 mm
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
219
Abbreviations
PI
PEG
PG
PIC
POST
PRTC
PXE
Abbreviation Term
MPI Multipoint-capable interface for programming devices
MPS Manageability Presence Server
MS-DOS
MTBF
Microsoft Disc Operating System
Mean Time Between Failures
MUI
NA
NAMUR
NC
NCQ
Multilanguage User Interface
Not Applicable
Normenarbeitsgemeinschaft for Mess- und
Regelungstechnik in der chemischen
Industrie (standardization body for instrumentation and control technology in the chemicals industry)
Not Connected
Native Command Queuing
NEMA
NMI
NTFS
ODD
OPC
PATA
PC
PCI
PCIe
PCMCIA
Meaning
Proxy for AMT
Language localization in Windows
National Electrical Manufacturers
Association
Non Maskable Interrupt
New Techniques File System
Optical Disk Drive
OLE for Process Control
Parallel ATA
Not connected
Automatic re-sorting of the file and disk access, for increased performance
Syndicate of manufacturers of electrical components in the
USA
Interrupt the processor can not reject
Secure file system for Windows versions (2000, XP, 7)
Standardized interface for industrial processes
Personal computer
Peripheral Component Interconnect High-speed expansion bus
Peripheral Component Interconnect express High-speed serial, differential full-duplex PtP interface with high data rate.
Personal Computer Memory Card
International Association
RAID
RAL
RAM
RI
ROM
RS 485
RTC
RTS
Protective Earth
PCI Express Graphics
Programming device
Programmable Interrupt Controller
Power On Self Test
Protected Real Time Clock
Preboot Execution Environment
Redundant Array of Independent Disks
Restricted Access Location
Random Access Memory
Ring Input
Read-Only Memory
Reconciliation Sublayer 485
Real Time Clock
Reliable Transfer Service
Protective conductor
Programmable interrupt controller
Clock in the management engine MEBx
Software for running new PCs without hard disk data via the network
Redundant hard disk array
Installation of device in operating facilities with restricted access - for example, a locked switchgear cabinet
Incoming call
Bi-directional bus system designed for up to 32 nodes.
Real-time clock
Request to send
220
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Abbreviations
Abbreviation Term
RxD Receive Data
SAS Serial attached SCSI
SATA
SCSI
SDRAM
SELV
SLC
Serial Advanced Technology Attachment
Small Computer System Interface
Synchronous DRAM
Safety Extra Low Voltage
Second Level Cache single-level cell
SMART
SMS
SNMP
SO-DIMM
SOL
SOM
SPP
SRAM
SSD
SVGA
SVP
SW
TCO
TFT
TTY
TxD
TXT
TWD
UEFI
UL
UMA
URL
USB
UXGA
V.24
VCC
VDE
VGA
VRM
VT
Self Monitoring Analysis and Reporting
Technology
Short Message Service
Simple Network Management Protocol
Small Outline Dual Inline Memory Module
Serial over LAN
SafeCard on Motherboard (SOM)
Standard Parallel Port
Static Random Access Memory
Solid State Drive
Super Video Graphics Array
Serial number of the device
Software
Total Cost of Ownership
Thin-Film-Transistor
Tele Type
Transmit Data
Trusted Execution Technology
Watchdog Time
Unified Extensible Firmware Interface
Underwriters Laboratories Inc.
Unified Memory Architecture
Uniform Resource Locator
Universal Serial Bus
Ultra Extended Graphics Array
Meaning
Data transfer signal
Safety extra low voltage
Memory cells in which only one bit per cell is saved
Hard disk error diagnostics program
Short message via telecommunication network
Network protocol
Text-based remote control
Synonym for parallel port
Static RAM
Enhanced VGA standard with at least 256 colors
Type of LCD flat-screen
Asynchronous data transfer
Data transfer signal
Hardware implementation
Watchdog monitoring time
US organization for tests and certifications according to own or binational standards (with CSA / Canada) standards.
Video memory
Designation of the full address of an Internet page
Graphic standard, maximum resolution 1600x1200 pixels.
ITU-T standardized recommendation for data transfer via serial ports.
Positive supply voltage of integrated circuits
Verein deutscher Elektrotechniker (Union of
German Electrical Engineers)
Video Graphics Array
Voltage Regulator Module
Virtualization Technology
Video adapter which meets industrial standard
Intel technology with which a virtually closed environment can be made available.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
221
Abbreviations
W2k
WAN
WAV
WD
WLAN
WoL
WWW
XD
XGA
ZMM
Abbreviation Term
VT-D Virtualization Technology for Directed I/O
Windows 2000
Wide Area Network
Wave Length Encoding
Watchdog
Wireless LAN
Wake on Local Area Network
Meaning
Enables the direct assignment of a device (e.g. network adapter) to a virtual device.
Loss-free file format for audio data.
Program monitoring with error detection and alarming.
LWireless local area network
World Wide Web
Execute Disable Capability Hardware implementation
Extended Graphics Array Graphic standard, maximum resolution 1024x768 pixels.
Zero Maintenance Cache Protection Module Maintenance-free cache unit for saving cache contents
222
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Glossary
AHCI mode
AHCI is a standardized method to address the SATA controller. AHCI describes a structure in the RAM, which contains a general area for control and status, as well as a command list.
APIC mode
Advanced peripheral interrupt controller. 24 interrupt lines are available.
ATAPI CD-ROM Drive
AT Bus Attachment Packet Interface (connected to AT bus) CD-ROM drive
Automation system (AS)
A programmable controller (PLC) of the SIMATIC S7 system consist of a central controller, one or several CPUs, and various I/O modules.
Backup
Duplicate of a program, data medium or database, used either for archiving purposes or for the protection of vital and non-replaceable data against loss when the working copy is corrupted. Certain applications automatically generate backup copies of data files, and manage both the current and the previous versions on the hard disk.
Baud
Physical unit for the step speed in signal transmission. Defines the number of transferred signal states per second. With only two states, one baud is equivalent to a transmission rate of 1 bps.
Boot disk
A boot disk is a disk with a "Boot" sector. This can be used to load the operating system from the disk.
Cache
High-speed access buffer for interim storage (buffering) of requested data.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
223
Glossary
CE marking
Communauté Européene The CE mark confirms compliance of the product with corresponding EC Directives, for example, with the EMC Directive.
Chipset
Located on the motherboard, connects the processor with the RAM, the graphics controller, the PCI bus, and the external interfaces.
Cold restart
A start sequence, starting when the computer is switched on. The system usually performs some basic hardware checks within the cold start sequence, and then loads the operating system from the hard disk to work memory -> boot
COM interface
The COM interface is a serial V.24 interface. The interface is suitable for asynchronous data transfer.
Compact Flash cards (CF)
Compact Flash is a digital storage medium in card format and without moving parts. The CF card contains the non-volatile memory and the controller. The interface of the CF card corresponds with the IDE interface. CF cards can be operated without additional electronics on PCMCIA or IDE hard disk controllers using a plug and socket adapter. There are two design forms: CF-I (42.6 x 36.4 x 3.3 mm) and CF-II (42.8 x 36.4 x 5 mm).
Configuration files
These are files containing data which define the configuration after restart. Examples of such files are CONFIG.SYS, AUTOEXEC.BAT and the registry files .
Configuration software
The configuration software updates the device configuration when new modules are installed
. This is done either by copying the configuration files supplied with the module or by manual configuration using the configuration utility.
Controller
Integrated hardware and software controllers that control the functions of certain internal or
I/O devices (for example, the keyboard controller).
224
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Glossary
Device configuration
The configuration of a PC or programming device contains information on hardware and device options, such as memory configuration, drive types, monitor, network address, etc.
The data are stored in a configuration file and enable the operating system to load the correct device drivers and configure the correct device parameters. . If changes are made to the hardware configuration, the user can change entries in the configuration file using the
SETUP program. .
Disc-At-Once
With this burning technique, data are written to a CD in a single session, and the CD is then closed. Further write access is then no longer possible.
DP
Display Port: New digital monitor interface.
Drivers
Dual Core CPU
Dual-core processors significantly increase the speed of computing and program execution compared to the previous generation of single-core processors with hyper threading technology.
ECC
Program parts of the operating system. They adapt user program data to the specific formats required by I/O devices such as hard disk, printers, and monitors.
Error checking and correction is a method for detecting and correcting errors when saving and transferring data, frequently used in conjunction with RAM modules with and without
ECC.
EMC directive
Directive concerning Electromagnetic Compatibility. Compliance is confirmed by the CE symbol and the EC certificate of conformity.
Energy management
The energy management functions of a modern PC allow individual control over the current consumption of vital computer components (e.g. of the monitor, hard disk and CPU), by restricting their activity based on the current system or component load. Energy management is of particular importance for mobile PCs.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
225
Glossary
Energy options
The energy options can be used to reduce energy consumption of the computer, while keeping it ready for immediate use. This can be configured in Windows by selecting Settings
> Control Panel > Energy options.
Enhanced Write Filter (EWF)
Configurable write filter that allows you, for example, to boot Windows Embedded Standard from write-protected media (such as CD-ROM), to write protect individual partitions and adapt the performance of the file system to your needs (when using Compact Flash cards).
ESD directive
Directive for using electrostatic sensitive components.
Ethernet
Local network (bus structure) for text and data communication with a transfer rate of
10/100/1000 Mbps.
Execute Disable Capability
Hardware implementation that prevents mutual memory accesses by programs and applications. It is only effective when all relevant system components, such as processors, operating systems and applications are supported.
Extensible Firmware Interface (EFI)
Refers to the central interface between the firmware, the individual components of a computer and the operating system. EFI is located logically beneath the operating system and represents the successor to PC BIOS, focusing on 64-bit systems.
File Based Write Filter (FBWF)
Configurable write filter to protect individual files from write access.
Formatting
Basic partitioning of memory space on a magnetic data medium into tracks and segments.
Formatting deletes all data on a data medium. All data media must be formatted prior to their first use.
Gender changer
Using the gender changer (25-pin / 25-pin), the COM1/V24/AG interface of the SIMATIC PC family can be converted to the usual 25-pin male connector.
226
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
HORM
Glossary
Hibernate once, resume many is a method for fast booting from a single Hibernate file that only needs to be created once. HORM ensures restoration of a uniform, saved system state when booting. This reduces the writing to a CompactFlash medium to a minimum, for example, when starting up and shutting down Windows Embedded Standard 2009.
Hot swap
The SATA interface gives the device's hard drive system hot swapping capability.
Prerequisite for this configuration is a RAID1 system with SATA RAID controller (onboard, or slot module), and at least two SATA removable drive bays. Advantages of hot swap: defective hard drives can be replaced without reboot.
Hub
Hyper Threading
HT technology (multi-threading) enables the parallel computing of processes. HT is only effective when all relevant system components, such as processors, operating systems and applications are supported.
IGD
A term in network technology. In a network, a device joining communication lines at a central location, providing a common connection to all devices on the network.
Integrated Graphics Device. Graphics interface integrated in the chipset.
Image
Intel Active Management Technology
This technology permits the diagnostics, management and remote control of PCs. It is only effective when all relevant system components, such as processors, operating systems and applications are supported.
Intel VT
This refers to the image, for example, of hard disk partitions saved to a file in order to restore them when necessary.
The Intel Virtualization Technology (IVT) is the implementation of a secure closed environment for applications. Special (visualization) software an a VT-capable processor is required for its use.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
227
Glossary
Interface
● Physical interconnection (cable) of hardware elements such as PLCs, PCs, programming devices, printers or monitors.
● Interface for interactive software applications.
Interface, multi-point
MPI is the programming interface of SIMATIC S7/M7. Allows remote access to programmable modules, text-based displays and OPs from central locations. The MPI nodes can intercommunicate.
LAN
Local Area Network: LAN is a local network that consists of a group of computers and other devices that are distributed across a relatively restricted range and are linked with communication cables. The devices connected to a LAN are called nodes. The purpose of networks is the mutual use of files, printers or other resources.
Legacy Boot Device
Conventional drives can be used as USB devices.
Legacy USB support
Support of USB devices (e.g. mouse, keyboard) on the USB ports without driver.
License key
The license key represents the electronic license stamp of a license. Siemens provides the license keys for protected software.
License key disk
The license key disk contains the authorizations or license keys required to enable protected
SIMATIC software.
Low-voltage directive
EC Product Safety Directive relating to the safety of products which are operated on low voltage (50 V AC to 1000 V AC, 70 V DC to 1500 V DC) and not specified in other directives.
Compliance is confirmed by the CE symbol and the EC certificate of conformity.
LPT interface
The LPT interface (Centronics interface) is a parallel interface that can be used to connect a printer.
228
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Memory card
Glossary
Memory cards in credit card format. Memory for user programs and parameters, for example, for programmable modules and CPs.
Module
Modules are plug-in units for PLCs, programming devices or PCs. They are available as central modules, interface modules, expansion cards or mass storage (mass storage module).
Motherboard
The motherboard is the core of the computer. Here, data are processed and stored, and interfaces and device I/Os are controlled and managed.
Operating system
Generic term which describes all functions for controlling and monitoring user program execution, distribution of system resources to the user programs and the operating mode in cooperation with the hardware (for example Windows XP Professional).
Packet writing
The CD-RW is used as a disk medium. The CD can then be read only by packet–writing compatible software or has to be finalized. Finalization of a CD closes the CD within an
ISO9660 shell. You can still write to the CD-RW several times in spite of finalization. Not all
CD drives can read packet-written CDs . There are restrictions to using this method in general data transfer.
PATA
Interface for hard disk drives and optical drives, with parallel data transmission rate up to 100
Mbps.
PC card
Trademark of the Personal Computer Memory Card International Association (PCMCIA).
Designation for auxiliary cards that conform with PCMCIA specifications. A PC card that has roughly the size of a credit card can be plugged into a PCMCIA slot. Version 1 specifies cards of Type I with a thickness of 3.3 millimeters, which are designed mainly for use as external memory. Version 2 of the PCMCIA specification also defines cards of Type II with a thickness of 5 mm and cards of Type III with a thickness of 10.5 mm. Type II cards can realize devices such as modems, fax cards and network interface cards. Type III cards are equipped with devices that require more space, for example wireless communications modules, or rotary storage media such as hard disk drives, for example.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
229
Glossary
PC/104 / PC/104-Plus
Two bus architectures are especially fashionable today in the industrial world: PC/104 and
PC/104-
Plus
. Both are standard in single-board computers of the PC class. The electrical and logical layout of the two bus systems is identical with ISA (PC/104) and PCI (PC/104-
Plus
). Software cannot usually detect a difference between them and normal desktop bus systems. Their advantage is the compact design and the resulting space they save.
PCMCIA
Association consisting of approx. 450 member companies of the computer industry whose focus is set on providing worldwide standards for miniaturization and flexible use of PC expansion cards in order to provide basic technologies to the market.
PEG interface
PCI Express for Graphics. Graphics interface with 16 PCIe lanes for expansions with graphics modules.
PIC mode
Peripheral interrupt controller. 15 interrupt lines are available.
Pixel
PixElement (picture point). The pixel represents the smallest element that can be reproduced on-screen or on a printer.
Plug&Play
Generally, a reference to the ability of a computer to automatically configure the system for communication with peripheral devices (for example monitors, modems or printers). The user can plug in a peripheral and "play" it at once without manually configuring the system. A
Plug&Play PC requires both a BIOS that supports Plug&Play and a Plug&Play expansion card.
POST
Self-test performed by the BIOS after the computer is switched on. Performs a RAM test and a graphics controller test, for example. The system outputs audible signals (beep codes) if the BIOS detects any errors; the relevant message indicating cause of error is output on the screen.
PROFIBUS/MPI
Process Field Bus (standard bus system for process applications)
230
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
PROFINET
Glossary
Programmable controller (PLC)
The programmable controllers (PLC) of the SIMATIC S5 system consist of a central controller, one or more CPUs, and various other modules (e.g. I/O modules).
PXE server
PROFINET is the name of the standard for Industrial Ethernet developed and maintained by the PROFIBUS user organization. PROFINET unites protocols and specifications with which
Industrial Ethernet meets the requirements of industrial automation technology.
A Preboot Execution Environment server is part of a network environment and can provide software to connected computers even before they boot. This can involve operating system installations or servicing tools, for example.
RAID
Redundant Array of Independent Disks: Data storage system which is used to save data and the corresponding error correction codes (parity bits, for example) to at least two hard disk volumes in order to enhance reliability and performance. The hard disk array is controlled by management programs and a hard disk controller for error correction. The RAID system is usually implemented in network servers.
RAL
Recovery CD
Contains the tools for configuring hard disks and the Windows operating system.
Reset
Restricted Access Location: Installation of the device in a production facility with restricted access, for example, a locked control cabinet.
Hardware reset: Reset/restart of the PC using a button/switch.
Restart
Warm restart of a computer without switching the power off (Ctrl + Alt + Del)
Restore DVD
The Restore DVD is used to restore the system partition or the entire hard disk to factory state if the system has crashed. The bootable DVD contains all the necessary image files.
You can also create a boot disk allowing restoration via the network.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
231
Glossary
ROM
Read-Only Memory ROM is a read-only memory in which every memory location can be addressed individually. The programs or data are permanently stored and are not lost in the event of a power failure.
S.M.A.R.T
The Self-Monitoring, Analysis and Reporting Technology (SMART or S.M.A.R.T.) is an industry standard integrated in storage media. It makes for permanent monitoring of important parameters and early detection of imminent problems.
SAS
Serial SCSI interface for connection of hard drives, for example, with serial data transmission
SATA
Serial ATA Interface for hard disk drives and optical drives with serial data transmission.
SCSI interface
Small Computer System Interface Interface for connecting SCSI devices such as hard disk drives or optical drives.
Session-At-Once
In session at once, the CD can be written to both with an audio session and a data session.
The two sessions are written to at once (as in disc at once).
SETUP (BIOS Setup)
A program in which information about the device configuration (that is the configuration of the hardware on the PC/PG) is defined. The device configuration of the PC/PG is preset with defaults. Changes must therefore be entered in the SETUP if a memory expansion, new modules or a new drive are added to the hardware configuration.
SSD (Solid State Drive)
A Solid State Drive is a drive that can be installed like any other drive; it does not contain a rotating disk or other moving parts because only semiconductor memory chips of similar capacity will be used. This design makes SSDs more rugged, provides shorter access times, low energy consumption and rapid data transfer.
STEP 7
Programming software for the creation of user programs for SIMATIC S7 controllers.
232
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Glossary
Track-At-Once
In track-at-once recording, a CD can be written to in bits in several sessions if the CD was not closed.
Troubleshooting
Error cause, cause analysis, remedy
Trusted Execution Technology
Hardware implementation that allows secured execution of programs and applications. It is only effective when all relevant system components, such as processors, operating systems and applications are supported.
Turbo Mode
In this mode individual processor cores can be clocked higher in accordance with the load from the user programs and as required. It is only supported by Core i5 and Core i7 processors.
V.24 interface
V.24 is a standardized interface for data transfer. Printers, modems, and other hardware modules can be connected to a V.24 interface.
Wake on LAN (WoL)
Wake on Local area network. This function allows the PC to be started via the LAN interface.
Warm restart
The restart of a computer after a program was aborted. The operating system is loaded and restarted again. The CTRL+ ALT+ DEL hotkey can be used to initiate a warm restart.
WLAN
Wireless LAN is a local network that transmits data via radio waves, infrared light or another wireless technology. Wireless LAN is mainly used for mobile computer applications in office or factory environments.
ZMM
Zero Maintenance Cache Protection Module is a functional unit of the SAS Raid controller that stores the data in the cache of the controller in the case of a voltage failure. This functional unit is maintenance-free.
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
233
Glossary
234
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Index
2
2 HDD system, (System with two drives)
A
AHCI controller
Making known to the operating system, (See storage controllers)
Assignment
B
Backup battery
Boot sequence
Bus board
Bus frame
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
C
Certifications and approvals, 133
Components sensitive to electrostatic charge, 135
Connecting
CPU cooler, (Processor cooler)
D
Data carrier controller
Making known to the operating system, 124
Device
Directive
235
Index
DisplayPort
Documentation and Drivers CD/DVD, 121
DPP, (DisplayPort)
Drive
Drivers
E
EC Declaration of Conformity, 134
Electromagnetic compatibility, 134
EMC, (Electromagnetic compatibility)
Error messages
Expansion
F
Fan, (Device fan)
Filter, (Filter mat)
Filter mat
Filter pad
236
G
H
Hard disk
installing in removable drive bay, 90
Second hard disk drive, (System with two drives)
I
I/O addresses
I/O devices
Installation
Installing
Installing language package, (See MUI)
Interface pinout
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
K
L
M
Marking
EC Declaration of Conformity, 134
Memory addresses
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Memory modules
Messages
Microsoft Windows Product Key, 34
Monitoring
Motherboard
Position of the interfaces, 151
N
O
Open
Operator panel
Index
237
Index
P
Partitions
Permitted mounting positions, 35
Pin assignment
Ports
POST codes
Power supply
Processor cooler
Protective measure
R
238
RAID controller
Making known to the operating system, (See storage controllers)
Displaying the defective HDD in the RAID
Integrating a new hard disk, 102
Management functions, 55, 58, 98
Mounting locations for hard disk drives, 92
Replacing a defective hard disk drive, 93
Status displays of the hard disk drives, 92
Redundant power supply
Removing
Restoring the factory state, 130
S
Safety information
SIMATIC software
Slave drive, (System with two drives)
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Software
Startup
Static electricity
Status displays
Strain relief
Network and fieldbus cables, 47
Switching off the device
Disconnect from mains voltage, 60
Forced shutdown, (Hardware reset)
Shutting down the operating system, 59
Switching on the device
Configure automatic startup, 51
T
Third-party expansion cards, 215
U
Update,
Updates
USB 3.0
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
V
W
Windows
Index
239
Index
240
SIMATIC IPC647D
Operating Instructions, 01/2015, A5E32996306-AB
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
Key features
19" rack-mountable
Rugged design
High performance
Variety of interfaces
Redundant power supply
RAID1 support
Industrial-grade components
Built-in monitoring functions
Easy integration with SIMATIC software
Frequently asked questions
The SIMATIC IPC647D is an industrial PC designed for use in automation and control applications. It is a rugged, compact, and high-performance PC that offers a wide range of features.
Key features include a 19" rack-mountable design, a rugged construction, a variety of interfaces, redundant power supply, RAID1 support, and industrial-grade components.
The SIMATIC IPC647D is mainly used in industrial automation and control applications such as process control, visualization, image processing, data acquisition, and quality assurance.
The SIMATIC IPC647D supports industrial applications by providing features such as a rugged design, wide operating temperature range, and built-in monitoring functions, ensuring reliable operation in harsh environments.
The SIMATIC IPC647D comes pre-installed with the Windows operating system. The specific version may vary depending on the configuration.
