Origin Acoustics Crown CDi CDi2000 Installation Manual
Add to My manuals7 Pages
Crown CDi 6000 Two-Channel 70V/140V Power Amplifier
The CDi 6000 is a high-powered, two-channel amplifier designed for commercial audio applications. It delivers 600 watts per channel at 70 volts or 140 volts, making it ideal for powering large speaker systems in a variety of settings, including stadiums, arenas, and theme parks.
The CDi 6000 features a number of advanced features that make it easy to use and configure. These features include:
- Selectable input sensitivity: The CDi 6000's input sensitivity can be set to 0.775V or 1.4V, making it compatible with a wide range of audio sources.
advertisement
Crown CDi Amplifier Set-Up
For Origin Landscape Speakers
Models:
CDi1000
CDi2000
CDi4000
LANDSCAPE CROWN AMPLIFIER INSTALLATION MANUAL
844·674·4461
TABLE OF CONTENTS
Introduction
Crown Amplifier Ins & Outs
Input Connections
Unbalanced (Most Common)
Balanced
Output Connections
Terminating The Wires
Which Preset To Use?
How To Load A Preset
How Many Speakers Can Be Run On Each Channel?
7
Technical Assistance 8
2
2
3
4
2
2
4
5
7
WWW.ORIGINACOUSTICS.COM
1
-
CH2
+ +
CH1
-
CH. 1 Source
CH. 2 Source
-
CH2
+ +
CH1
-
CH. 1 Source
INTRODUCTION
Origin Landscape speakers are designed so they can be part of a
70V system or an 8Ω system for smaller installs using a standard receiver. As part of a 70V system, they will need to be paired with a Crown CDi amplifier that has been designed to work with our
Landscape speakers. This manual will specifically cover setup with a Crown CDi amplifier in 70V mode.
• For more detailed information about the Crown CDi amplifier, refer to the Crown Operation Manual.
• For useful information about the relative merits of different wiring plans you may want to refer to the speaker installation manual (available on-line).
Shield
CROWN AMPLIFIER INs & OUTs
Input connections
+ +
CH1
-
To connect your audio source to the Crown amplifier you will usually need cables with RCA connectors on the source end and bare wire on the Landscape amplifier end. The Crown amplifier channels are labeled CH1 and CH2. Both channels are identical.
Attach the bare wires from your cable to the Phoenix style connector provided in the amplifier box. Note the location of the positive and ground wires on the Phoenix connector. You must run a jumper wire from the ground terminal to the negative terminal; see Figure 1.
Shield
Figure 1
Balanced
When using the Origin Landscape series in a commercial installation it might be necessary to connect the amplifier using balanced wiring. Connect the wires from your source equipment to the Phoenix connector. Be sure to observe proper polarity when connecting the wires to the Phoenix connector. If your source equipment uses XLR connectors please confirm the polarity or pin out of your source equipment before terminating the Phoenix connector. see figure 2
CH. 1 Source
CH. 2 Source
Figure 2: Balanced Lines to the Phoenix connectors
NOTE
WHEN USING BALANCED INPUTS PLEASE CONSULT THE CROWN® AMPLI-
FIER MANUAL FOR GREATER DETAIL.
2
844·674·4461
Shield
WWW.ORIGINACOUSTICS.COM
3
Output Connections
Terminating the wires
Attach the supplied spade connectors to the ends of your speaker cables. Once the connectors are installed then connect the spades to the output connectors on the amplifier. Once your connections are finished place the supplied plastic cover over the connectors to prevent a short circuit or shock hazard.
CAUTION
-
CH2
+ are completed. High power 70v amplifiers present a serious shock hazard.
Do not connect speaker wires to the amplifier until all other connections are completed.
+
CH1
The amplifier should not be connected to AC power until all connections
LANDSCAPE CROWN AMPLIFIER INSTALLATION MANUAL
WHICH PRESET TO USE?
The Crown CDi series amplifier you purchased from Origin Acoustics is preloaded with 18 presets to allow allow you to optimally configure your sound system for practically any circumstance.
The presets have been divided into two families -- the Active
Crossover family and the Passive Crossover family.
The Active Crossover family is recommended for most installs. It will have the subwoofers on one wire run (must be channel 1) and the satellite speakers on the other (must be channel 2). The active crossover removes the bass from the satellites, more effectively controls how the subwoofer interfaces with the satellites and allows the custom DSP (digital signal processing) to fed only to the speakers they were designed for.
• Preset 8 is designed to make the LS 64 sound full range when no subwoofer is to be used.
• Presets 15-19 require 2 or more amplifiers. They are intended for larger installs and also give you greater control over the balance between the subwoofer and the satellites.
• The Passive Crossover family, which is the approach you may be most familiar with, allows satellites and subwoofers to be on a single wire run.
• Presets 6 & 7 use the amplifier in bridged mode if only one channel is available. This is anticipated to be used when wire is pre-existing from a previous install.
Shield
4
844·674·4461
WWW.ORIGINACOUSTICS.COM
5
EQ Presets on Crown CDi amplifiers for Origin Acoustics
6
1
Implications & Recommendations
When Satellites & Subwoofers are on the same wire runs
(Passive crossover family)
DSP OFF
2 PX8-44
3 PX8-64
4 PX10-44
5 PX10-64
8
8
10
10
44
64
44
64
No EQ or active crossover
6 Br44
7 Br64
8
8
44 Bridged amp yields a single channel of
64 output
When Satellites & Subwoofers are on separate, designated wire runs
(Active crossover family: Subwoofers on CH1, Satellites on CH2)
8 AX0-64
9 AX8-44
10 AX8-64
11 AX10-44
12 AX10-64
13 AX12-44
14 AX12-64
15 AX-44
16 AX-64
17 AX-8
0
8
8
10
10
12
12
8
64 No Sub
44 Subwoofers on one run & Satellites on
64
44
64
44
64 another run.
44 Satellites only. Subs to use second amp
64
18 AX10/12-44 10/12 44 Subs only. For use with LS44 Satellites on a second amp
19 AX10/12-64 10/12 64 Subs only. For use with LS64 Satellites on a second amp
20 Open Open
844·674·4461
LANDSCAPE CROWN AMPLIFIER INSTALLATION MANUAL
How to Load a Preset
1. Press the Select / Enter button on the front of the amplifier.
2. Press the Next / Down button until the word PRESET appears on the display.
3. Press the Select / Enter button
4. Press the Next / Down or Prev / Up buttons until the preset you desire is displayed
5. Press the Select / Enter button
6. Your chosen preset should now be displayed
HOW MANY SPEAKERS CAN BE
RUN ON EACH CHANNEL?
Origin Landscape speakers use an adjustable 70 volt transformer that not only let you to set speaker’s volume level relative to the other speakers in the system, but also allows you to increase the number of speakers that can be run on each channel. The chart below shows the maximum number of speakers you can use before the load becomes unsafe for the Crown CDi amplifiers (2Ω load). If you’re using the amplifier in bridged mode you’ll need to divide the maximum speaker number in half.
LS64 LS44 OSUB8 OSUB10 OSUB12
Setting Max Setting Max Setting Max Max Max
8 ohm 4
50W 36
8 ohm 4
30W 60
8ohm
70V
2
14 8 8
25W
12W
6W
50 15W
100 7W
200 4W
100
300
500
WWW.ORIGINACOUSTICS.COM
7
Technical Assistance
If you have any questions or concerns about installing or using this product, you can reach us through one of the following methods:
Phone: (844) 674-4461
Hours of operation: 8:00am - 5:00pm (Pacific Time), Mon - Fri
Email: [email protected]
If you are having technical trouble, please include the model number and briefly explain what steps you took to resolve the problem in your email, or be prepared to answer these questions over the phone. If you are considering returning the product, it’s required that you contact Origin Acoustics prior to any return attempts.
This way we can determine if the issue can be resolved without returning the product, or if needed we can provide instructions and support for the return process.
LANDSCAPE CROWN AMPLIFIER INSTALLATION MANUAL
8
844·674·4461
WWW.ORIGINACOUSTICS.COM
©2014 Origin Acoustics. All copyrighted, trademarked and patented elements mentioned herein are the sole property of
Origin Acoustics.
advertisement