Installation and Assembly:
Dedicated Tilt Wall Mount
Model:
ST24D
Max Load Capacity: 200 lb (91 kg)
2300 White Oak Circle • Aurora, IL 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.com
ISSUED: 09-15-05 SHEET #: 202-9032-4 10-04-11
Note: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112.
• This product should only be installed by a qualified professional.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Never exceed the Maximum Load Capacity of 200 lb (91 kg).
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an
"edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power.
Tools Needed for Assembly
• stud finder ("edge to edge" stud finder is recommended)
• phillips screwdriver
• drill
• 5/16" bit for concrete and cinder block wall
• 5/32" bit for wood stud wall
• level
• 6 mm allen wrench
Accessories
• Metal Stud Fastener Kit (ACC 415) (Not evaluated by UL)
Table of Contents
Parts List .............................................................................................................................................................................. 3
Installation to Double Wood Stud Wall .................................................................................................................................. 4
Installation to Solid Concrete or Cinder Block ....................................................................................................................... 5
Attaching PLP Adapter Plate to Tilt Bracket Assembly ........................................................................................................ 6
Attaching LC Adapter Plate to Tilt Bracket Assembly ........................................................................................................... 7
Mounting and Removing Flat Panel Screen ........................................................................................................................... 8
Adjusting the Tilt Angle of the Flat Panel Screen .................................................................................................................. 9
2 of 9 ISSUED: 09-15-05 SHEET #: 202-9032-4 10-04-11
Parts List
Description
AA wall plate
BB tilt bracket assemby
CC #14 x 2.5" wood screw
DD Alligator® anchor
EE M10 x 15 mm socket head screw
FF 4 mm security allen wrench
1 200-1796
1 200-0936
4 5S1-015-C03
4 590-0097
4 520-9262
1 560-1146
BB
AA
CC DD
EE FF
3 of 9 ISSUED: 09-15-05 SHEET #: 202-9032-4 10-04-11
Installation to Wood Stud Wall
WARNING
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
1 Using a stud finder, locate the edges of the wood studs used in mounting this product. Use of an edge-to-edge stud finder is highly recommended. Based on its edges and using a level, draw a vertical line down the center of each stud. Mark a point ( point 1 ) on the right stud centerline 2.1" above the center of screen as shown in figure 1.1. Hold wall plate ( AA ) over point 1. Using a level to ensure plate is horizontal, mark three more points ( points 2, 3, and 4 ) as shown in figure 1.2.
Drill 5/32" diameter holes 2-1/2" deep through studs at the four points.
Loosely fasten wall plate ( AA ) to wall using four #14 x 2-1/2" wood screws ( CC ) as shown in figure 1.3.
Note : For ease of installation, start with the top right wood screw first and work counterclockwise.
Level, hold, and then tighten all screws.
Skip to step 2 on page 6.
CL CL CL CL
POINT 1
POINT 2
POINT 1
2.1"
(53 mm)
CS
POINT 3
CS POINT 4
fig 1.1
CS = center of screen
CL = stud centerline
fig 1.2
WARNING
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is highly recommended.
CC
4 of 9
fig 1.3
AA
ISSUED: 09-15-05 SHEET #: 202-9032-4 10-04-11
Installation to Solid Concrete and Cinder Block Wall
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications.
It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
1 Position wall plate ( AA ) on wall so that upper slots are 2.1" above desired center of screen.
Use wall plate ( AA ), making sure that it is level, as a template to mark holes. Drill four 5/16" (8 mm) dia. holes to a minimum depth of 2-1/2" (64 mm). Concrete must be
2000 psi density minimum. Insert anchors ( DD ) in holes flush with wall as shown in figure 1.4. Place wall plate ( AA ) over anchors and secure with
#14 x 2-1/2" (6 mm x 64 mm) wood screws ( CC ) as shown in figure 1.5. Make sure wall plate is level and tighten all fasteners.
1 concrete surface
DD
Drill holes and insert anchors ( DD ).
2 AA
CC DD
Place plate ( AA ) over anchors ( DD ) and secure with screws ( CC ).
3
WARNING
• Tighten wood screws firmly, but do not overtighten.
Overtightening can damage the screws, greatly reducing their holding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Concrete anchors are not intended for attachment to concrete wall covered with a layer of plaster, drywall, or other finishing material as shown right. If mounting to concrete wall covered with plaster/drywall is unavoidable, plaster/drywall (up to 5/8" thick) must be counterbored as shown below. Be sure concrete anchors do not pull away from concrete when tightening screws. If plaster/drywall is thicker than
5/8", custom fasteners must be supplied by installer.
Tighten all fasteners.
fig 1.4
DD fig 1.5
wall plate
INCORRECT concrete wall plate
CORRECT concrete
AA
CC
plaster/ dry wall plaster/ dry wall
5 of 9 ISSUED: 09-15-05 SHEET #: 202-9032-4 10-04-11
Note: Refer to accompanying instruction sheet for attachment of adapter plate to screen before proceeding with step 2.
Attaching PLP Adapter Plate to Tilt Bracket Assembly
2 Attach adapter bracket to interface bracket of tilt bracket assembly ( BB ) using four M10 screws ( EE ).
Note: Full tilt bracket assembly not shown for clarity.
BB
( NOTE: INTERFACE
BRACKET SHOWN
WITHOUT FULL TILT
BRACKET ASSEMBLY FOR
CLARITY)
EE
ADAPTER PLATE
6 of 9 ISSUED: 09-15-05 SHEET #: 202-9032-4 10-04-11
Note: Refer to accompanying instruction sheet for attachment of adapter plate to screen before proceeding with step 2.
Attaching LC Adapter Plate to Tilt Bracket Assembly
2 To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place screen face side down. Attach the interface bracket of tilt bracket assembly ( BB ) to the LC adapter plate (sold separately) using four M5 screws provided with plate as shown.
WARNING
• Tighten screws so interface bracket is firmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached.
Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
GENERIC LC ADAPTER
PLATE
BB
( NOTE: INTERFACE
BRACKET SHOWN
WITHOUT FULL TILT
BRACKET ASSEMBLY FOR
CLARITY)
M5 SCREWS
7 of 9 ISSUED: 09-15-05 SHEET #: 202-9032-4 10-04-11
Mounting and Removing Flat Panel Screen
3 Hook tilt bracket assembly ( BB ) onto wall plate ( AA ). Then slowly swing screen in as shown. To lock the screen down, tighten security screw to wall plate using security allen wrench ( FF ) as shown in detail 1.
Screen can be adjusted horizontally if desired.
To remove screen from mount, loosen security screws, swing screen away from mount, and lift screen off of mount.
WARNING
• Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television.
BB
AA
SECURITY
SCREWS
BB
DETAIL 1
AA
8 of 9 ISSUED: 09-15-05 SHEET #: 202-9032-4 10-04-11
Adjusting the Tilt Angle of the Flat Panel Screen
4 Adjust tension knob on right side of mount shown in detail 2 to desired tension to balance your screen size and weight.
Push or pull from top or bottom of screen to adjust tilt as shown in figure 4.1. The tilt can be adjusted to a maximum of 15° forward or 5° backward.
Note: To lock the screen into the desired tilt position, tighten tension screws on both sides of mount shown in figure 4.2 and detail 3 using wrench ( FF ).
CAUTION
• Do not tighten screws with excessive force.
Overtightening can cause damage to mount.
Tighten screws to 40 in. • lb (4.5 N.M.) maximum torque.
CAUTION
• Be careful not to pinch fingers when pushing screen from the bottom.
fig 4.1
DETAIL 2
TENSION
KNOB
TENSION
SCREW
FF
DETAIL 3 fig 4.2
9 of 9 ISSUED: 09-15-05 SHEET #: 202-9032-4 10-04-11
© 2011 Peerless Industries, Inc. All rights reserved.
SmartMount is a trademark and Peerless is a registered trademark of Peerless Industries, Inc.
All other brand and product names are trademarks or registered trademarks of their respective owners.
