Installation and Assembly:
OneMount™
Models: ONE-TP, ONE-TP-S
R
This product is UL Listed. It must be installed by a qualified professional installer.
Max UL Load Capacity 250lb (113.5kg)
Features:
• For flat panel screens
• One-touch tilt for effortless positioning and adjustment of the screen
• Ultra-slim design holds the screen flat against the wall
• IncreLok™ locking tilt positions for specific tilt settings in 5° increments
• Comes in black or silver
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
ISSUED: 09-20-06 SHEET #: 202-9167-1
Note: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-729-0307.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Never exceed the Maximum UL Load Capacity. See page one.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an
"edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power.
Tools Needed for Assembly
• stud finder ("edge to edge" stud finder is recommended)
• phillips screwdriver
• drill
• 1/4" bit for concrete and cinder block wall
• 5/32" bit for wood stud wall
• level
• 7/16" socket or crescent wrench
• tape measure
Table of Contents
Parts List .............................................................................................................................................................................. 3
Adjusting Tilt Brackets .......................................................................................................................................................... 4
Installing Tilt Brackets ........................................................................................................................................................... 5
Installation to Double Wood Stud Wall .................................................................................................................................. 7
Installation to Triple Wood Stud Wall .................................................................................................................................... 8
Installation to Solid Concrete or Cinder Block ....................................................................................................................... 9
Mounting and Removal of Flat Panel Screen ....................................................................................................................... 10
For customer care call (800) 729-0307 or (708) 865-8870.
2 of 10
ISSUED: 09-20-06 SHEET #: 202-9167-1
Before you begin, make sure all parts shown are included with your product.
Parts may appear slightly different than illustrated.
Parts List
Description
AA wall plate
BB left tilt bracket
CC right tilt bracket
DD #14 x 2.5 wood screw
EE alligator® anchor
FF 1/4 serrated flanged locknut
G G wing bracket
HH M5 x 25mm security screw
II
wrench
BB
top extension bracket
CC
4
2
6
6
1
1
Qty.
1
2
1
GG
Black
Part #
201-1210
201-0181
201-0177
5S1-015-C03
590-0097
530-1021
201-1134
520-1122
560-1146
FF
Silver
Part#
201-4210
201-0192
201-0193
5S1-015-C03
590-0097
530-1021
201-4134
520-1122
560-1146
AA
DD
Security Option
NOTE: Replace safety screw in each tilt bracket with M5 x 25 security screw (HH) using wrench (II).
II HH
EE
bottom extension bracket
Adapter Bracket Fasteners
M4 x 12 mm (6)
(504-9013)
M4 x 25 mm (4)
(504-1015)
M5 x 12 mm (4)
(520-1027)
M5 x 25 mm (4)
(520-9543)
M6 x 12 mm (4)
(520-1128)
M6 x 20 mm (4)
(520-9402)
M6 x 25 mm (4)
(520-1208)
M6 x 30 mm (4)
(510-9109)
M8 x 16 mm (6)
(520-9257)
M8 x 25 mm (4)
(520-1031)
Parts may appear slightly different than illustrated.
M8 x 40 mm (4)
(520-1136)
I.D. 5.6 mm (4)
(540-1057)
I.D. 8.7 mm (4)
(540-1059)
3 of 10
multi-washer (6)
(580-1036)
ISSUED: 09-20-06 SHEET #: 202-9167-1
Adjustment of Extension Brackets
Loosen four 1/4-20 x 1/4" screws on each adapter bracket (BB,CC). Position extension brackets, with slots
facing downward, onto adapter brackets (BB,CC) at the appropriate position to accommodate your screen as shown in Figure 1.1. Securely tighten all 1/4-20 x 1/4" screws as shown in figure 1.2.
NOTE: In all bracket extension positions, stops and 1/4-20 x 1/4" screws must be engaged in slots as shown in figure 1.2.
TOP
EXTENSION
BRACKET
BB,CC
ADAPTER
BRACKET
1/4-20 x 1/4"
SCREWS
TIGHTEN
FASTENERS
BB,CC
STOP
STOP
BOTTOM
EXTENSION
BRACKET
fig 1.1
Make sure slots face downward.
fig 1.2
4 of 10
ISSUED: 09-20-06 SHEET #: 202-9167-1
n
Installing Tilt Brackets
Refer to Screen Compatibility Chart to determine the proper fasteners to use.
NOTE: Refer to page 4 for adjustments of top extension bracket.
To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached.
Place tilt brackets (BB and CC) on back of screen. Align to holes, and center on back of screen as shown in figure
2.1. Attach the tilt brackets to the back of the screen using the appropriate combination of screws, multi-washers, and spacers as shown in figure 2.3. NOTE: Be sure to attach tilt brackets with knobs facing outward as in figure
2.1.
NOTE: Top and bottom mounting holes must be used for attaching brackets. Middle holes should also be used where the fasteners and screens allow.
Verify that all holes are properly aligned, and then tighten screws using a phillips screwdriver.
WARNING
• Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force.
Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to
40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail.
fig 2.1
BB
CENTER BRACKETS
VERTICALLY ON
BACK OF SCREEN
CC
X
KNOBS
FACE OUT
X
Note: "X" dimensions should be equal.
NOTES:
• Always use multi-washers when attaching tilt brackets (BB and CC) to your screen.
• Use the corresponding hole in the multiwasher that matches your screw size as shown in figure 2.2.
• Spacers may not be used, depending upon the type of screen.
BB
MEDIUM HOLE FOR M5 SCREWS
SMALL HOLE FOR M4 SCREWS
LARGE HOLE FOR M6 SCREWS
fig. 2.2
MULTI-WASHER
fig 2.3
SCREW
MULTI-
WASHER
SPACER
CC
5 of 10
ISSUED: 09-20-06 SHEET #: 202-9167-1
With tape measure, measure the outside to outside of the brackets on the back of your screen. If width of the tilt brackets on back of the screen is over 18-1/2" shown in figure 3.1, using a wrench, attach wing bracket (GG) to center bracket using two 1/4 serrated flanged locknuts (FF) as shown in figure 3.2. If width of the brackets on back of the screen is over 30-3/8", using a wrench, attach second wing bracket (GG) to center bracket using two 1/4 serrated flanged locknut (FF) as shown in figure 3.3.
CAUTION: If mounting to two studs on 16" centers, and using the three plate configuration, A STUD
MUST BE SKIPPED in the middle so distance between studs is 32".
18.5"
AA
AA
fig. 3.1
FF
GG
fig. 3.2
AA
GG
FF
6 of 10
fig. 3.3
ISSUED: 09-20-06 SHEET #: 202-9167-1
Installation to Double Wood Stud Wall
WARNING
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations.
NOTE: If mounting equipment weighing greater than 200 lbs, triple stud mounting is strongly recommended.
Skip to page 8
Wall plate (AA) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the studs.
Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each stud’s center. Place wall plate on wall as a template. The top mounting slots should be 2.5" above the desired screen center as shown in figure 4.1. Level plate, and mark the center of the four mounting holes. Make sure that the mounting holes are on the stud centerlines. Drill four 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the wall plate is level, secure it using four #14 x 2.5" wood screws (DD) as shown in figure 4.2.
NOTE: Wall plate may be mounted up to 4" (102 mm) off center as shown in figure 4.1.
Skip to step 5.
4"
(102 mm)
STUD
AA
4"
(102 mm)
2.5"
(64 mm)
CS
CS = center of screen
fig. 4.1
7 of 10
DD
AA
fig. 4.2
ISSUED: 09-20-06 SHEET #: 202-9167-1
Installation to Triple Wood Stud Wall
WARNING
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations.
Wall plate (AA) can be mounted to three studs that are 16" apart. Use a stud finder to locate the edges of the studs.
Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each stud’s center. Place wall plate on wall as a template. The top mounting slots should be 2.5" above the desired screen center as shown in figure 4.3. Level plate, and mark the center of the six mounting holes. Make sure that the mounting holes are on the stud centerlines. Drill six 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the wall plate is level, secure it using six #14 x 2.5" wood screws (DD) as shown in figure 4.4.
NOTE: When mounting equipment weighing greater than 200 lbs, triple stud mounting is strongly recommended. If mounting to two studs on 16" centers, leave an open stud in center. Wall plate may be mounted up to 4" (102 mm) off-center as shown in figure 4.3.
Skip to step 5.
STUD
4"
(102 mm)
4"
(102 mm)
AA
CS
2.5"
(64 mm)
CS = center of screen
fig. 4.3
AA
8 of 10
DD
fig. 4.4
ISSUED: 09-20-06 SHEET #: 202-9167-1
Installation to Solid Concrete or Cinder Block
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
Make sure that wall plate (AA) is level, use it as a template to mark four mounting holes. The top mounting hole should be 2.5" above the desired screen center as shown in figure 4.1 on page 7. Drill four 1/4"
(6 mm) dia. holes to a minimum depth of 2.5" (64 mm).
Insert anchors (EE) in holes flush with wall as shown
(right). Place wall plate over anchors and secure with
#14 x 2.5" screws (DD). Level, then tighten all fasteners.
1
concrete surface
EE
NOTE: Six holes and six sets of fasteners are required when mounting the wall plate for equipment weighing greater than 200 lbs.
Drill holes and insert anchors (EE).
2
AA
WARNING
• Tighten screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
DD
EE
Place plate (AA) over anchors (EE) and secure with screws (DD).
3
WARNING
• Always attach concrete anchors directly to loadbearing concrete.
• Never attach concrete anchors to concrete covered with plaster, drywall, or other finishing material. If mounting to concrete surfaces covered with a finishing surface is unavoidable, the finishing surface must be counterbored as shown below. Be sure concrete anchors do not pull away from concrete when tightening screws. If plaster/drywall is thicker than 5/8", custom fasteners must be supplied by installer.
(Not evaluated by UL)
INCORRECT CORRECT
Tighten all fasteners.
DD
AA
solid concrete
EE
cinder block concrete wall plate wall plate concrete plaster/ dry wall plaster/ dry wall
9 of 10
ISSUED: 09-20-06 SHEET #: 202-9167-1
Mounting and Removing Flat Panel Screen
WARNING
• Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television.
BB and CC
NOTE: For security, replace safety screw in each tilt bracket with M5 x 25 security screw (HH) using wrench (II).
Adjust brackets to full back tilt position and tighten.
Hook tilt brackets (BB and CC) onto wall plate (AA).
Then slowly swing screen in as shown. Turn safety screws, using phillips screw driver, clockwise till fully tightened down and screw tip securely contacts bottom of the wall plates as shown in detail 1. of figure 5.1.
Center of screen can be adjusted horizontally no more than 4" from center of the wall plate configuration, if desired as shown in figure 5.2.
AA
SAFETY
SCREW
DETAIL 1
AA
NOTE: To lock the screen down, tighten safety screws to wall plate using a phillips head screw driver as shown in detail 1.
To remove screen from mount, loosen safety screws, swing screen away from mount, and lift screen off of mount.
4"
CAUTION
CS
• Do not tighten screws with excessive force.
Overtightening can cause damage to mount. Tighten screws to 40 in. • lb (4.5 N.M.) maximum torque.
fig 5.1
CAUTION
CS = center of screen
fig 5.2
• Be careful not to pinch fingers when pushing screen from the bottom.
Adjusting the Tilt Angle of the Flat
Panel Screen
Adjust tension knobs shown in detail 2 to desired tension, balancing your screen size and weight. The tension knob, without changing the bracket tension, can be pulled out, away from the bracket and turned independently of the knob post for readjustment as shown in Detail 3.
TENSION
KNOB
TILT POSITION
HOLES
Push or pull from top or bottom of screen to adjust tilt as shown in figure 6.1. The tilt can be adjusted to a maximum of 15° forward or 5° backward.
TENSION
KNOB
NOTE: To lock the screen into the desired tilt position, use locator hole to find tilt position hole.
Tighten IncreLok™ tilt locking screws on both tilt brackets as shown in figure 6.1 and detail 2.
DETAIL 2
LOCATOR
HOLE
IncreLok™
TILT LOCKING
SCREW
fig 6.1
DETAIL 3
10 of 10
ISSUED: 09-20-06 SHEET #: 202-9167-1
© 2006 Peerless Industries, Inc. All rights reserved.
Onemount is a trademark and Peerless is a registered trademark of Peerless Industries, Inc.
All other brand and product names are trademarks or registered trademarks of their respective owners.
