JRC JCY-1800 - Installation Manual

JCY-1800/1850
VDR/S-VDR
VDR/S-VDR Real Time Monitor
Installation Manual
Version 1.2
Record of Revisions
Record of Revision
Rev
1.0
1.2
Description
Date
First Edition
07-Feb-1
Added example of connection
Approved by
Checked by
st
M.Takayama
R.Uchijima
rd
M.Takayama
R.Uchijima
07-Jul-23
VDR/S-VDR Real Time Monitor / Installation Manual
i
Before Using
< Before Using >
Icons
This manual and product employ various icons to enable users to use the product safety and
correctly, and to prevent any harm to users or others, and to prevent damage to the property.
The icons and the meanings are indicated below.
WARNING
CAUTION
Incorrect use of the equipment by ignoring this icon may cause death
or a seruous injury.
Incorrect use of the equipment by ignoring this icon may cause an
injury or physical damage.
Example of icons
The △ symbole indicates a caution (including danger or warning).
Inside of the symbol indicates the actual details (this icon indicates the
caution regarding electric shock).
Electric
shock
Disassembly
The
symbol indicates prohibition.
The actual contents (this icon indicates “disassembly prhibited”) are
provided inside or alongside of the symbol
prohibited
Remove
The ● symbol indicates an action or insutruction. The actual contenst (this
icon indicates removal of the power plug from socket) are provided inside of
the symbol
Plug
VDR/S-VDR Real Time Monitor / Installation Manual
ii
Notes on Using
< Notes on Using >
Do not disassemble or remodel this equipment.
Such action may cause fire, electric shock, or an equipment fault.
Do not use any AC/DC adaptor other than attachment.
Such action may cause fire, electric shock, or an equipment fault.
Do not use any power supply voltage other than the specified voltages.
Such action may cause fire, electric shock, or an equipment fault.
Do not use any battery other than specification.
Such action may cause burst of a battery by liquid leak, fire, or injury.
Do not put containers into which it went, such as water, or a small metal thing on
this equipment top or near.
When water enters or a metal thing falls into the equipment, it becomes the cause
of a fire, an electric shock, and failure.
Do not damage a power cord or process it.
If put a heavy thing, heat, it pulls or it bends by force, a power cord will be
damaged and it may become the cause of fire and electric shock.
When a fault occurs, turn off the power supply of this equipment, remove the plug,
and contact the Sales Department of Japan Radio Company, nearest branch
company, branch office, sales office, or our agent.
Continuous use may cause fire or electric shock.
Do not check or repair the inside of the equipment by yourself.
Checking or repair by anyone other than the specialist maintenance staff may
cause fire or electric shock.
Request checking or repair of the inside of the equipment to the sales Department
of Japan Radio Company, nearest branch company, branch office, sales office, or
our agent.
VDR/S-VDR Real Time Monitor / Installation Manual
iii
Before Using
CAUTION
Do not install the equipment in the location affected by water, humidity, dust, or
soot. It may become the cause of fire, electric shock, or a fault.
Do not put in from a vent foreign substance, such as metal or a thing which is
easy to burn.
It may become the cause of fire, electric shock, or a fault.
Do not put on a place with many vibration and shocks.
It may fall and may become the cause of an injury and failure.
Do not wet this equipment or do not put in water.
It may become the cause of electric shock, or a fault.
Do not plug up the vent of this equipment.
It may be filled with heat and fire and failure may occur.
When the equipment is not used for a long time, pull out a power supply plug
from a wall socket for safety.
It may become the cause of fire or electric shock.
Pull out a plug from a wall socket for safety at the time of care.
It may become the cause of fire or electric shock.
Be careful of a computer virus.
If a computer is infected with a virus, it may suffer the damage of an unusual
display, a program, and data being destroyed, and may become the cause of
failure.
Please confirm whether it is infected with the computer virus, using a virus
checker program periodically.
VDR/S-VDR Real Time Monitor / Installation Manual
iv
Contents
<Contents>
< Before Using > ...................................................................................................................... ii
< Notes on Using >.................................................................................................................. iii
Chapter1 Installation Procedure...............................................................................................1
Chapter2 System Composition.................................................................................................3
2.1 Basic Composition ......................................................................................................................... 3
2.2 In case of connecting with user LAN ............................................................................................. 4
2.3 In case of connecting with Radar IF (NWP-46) ............................................................................. 5
Chapter3 Wiring Diagrams .......................................................................................................7
Chapter 4 Wiring ....................................................................................................................11
4.1 In case of JCY-1800 VDR ........................................................................................................... 11
4.2 In case of JCY-1850 S-VDR........................................................................................................ 12
4.3 Wiring to VDR IF（Router）........................................................................................................ 13
Chapter5 Setup VDR/S-VDR by Maintenance software ........................................................15
Chapter6 PC (Server/Client) Setup ........................................................................................19
6.1 PC Specification .......................................................................................................................... 19
6.2 Setup Items of PC........................................................................................................................ 19
6.2.1 Set the IP address .............................................................................................................................. 19
6.2.2 Stop automatic synchronization with an Internet time server .............................................................. 23
6.2.3 Stop the Remote Assistance............................................................................................................... 24
6.2.4 Stop the Automatic Updates ............................................................................................................... 26
6.2.5 Stop the Error Reporting ..................................................................................................................... 28
6.2.6 Invalidate the Windows Firewall.......................................................................................................... 31
6.2.7 Set the Power Options ........................................................................................................................ 35
6.3 Install the VDR/S-VDR Real Time Monitor software ................................................................... 37
6.4 Uninstall the VDR/S-VDR Real Time Monitor software............................................................... 41
6.5 Initial setup for the VDR/S-VDR Real Time Monitor.................................................................... 42
6..5.1 Setup.................................................................................................................................................. 43
Chapter7 Final Check.............................................................................................................57
Chapter8 Trouble Shooting ....................................................................................................59
VDR/S-VDR Real Time Monitor / Installation Manual
v
Contents
Chapter9 Appendix.................................................................................................................61
9.1 How to eject CF card from VDR/S-VDR ...................................................................................... 61
9.2 Example of connection ................................................................................................................ 63
9.2.1 Example1
In case of only one VDR/S-VDR Real Time Monitor........................................................ 65
9.2.2 Example2
In case of connecting with Client PC ............................................................................... 70
9.2.3 Example3
In case of connecting with Client PC and Radar IF ......................................................... 78
9.2.4 Example4
In case of connecting with Client PC ............................................................................... 88
9.2.5 Example5
In case of connecting with Client PC and VDR IF............................................................ 98
9.2.6 Example6
In case of connecting with Client PC ............................................................................. 110
9.2.7 Example7
In case of connecting with Client PC and Radar IF ....................................................... 123
9.3 Hyper Terminal Setup................................................................................................................ 142
9.3.1 Starting.............................................................................................................................................. 142
9.3.2 End 144
9.4 Installation Flow for Server PC .................................................................................................. 145
9.5 Installation Follow for Client PC................................................................................................. 146
VDR/S-VDR Real Time Monitor / Installation Manual
vi
Chapter1 Installation Procedure
Chapter1 Installation Procedure
General Procedure
(1) Mounting the necessary unit
(2) Wiring the cable connected unit in according with installation drawings
(3) Checking wiring condition
(4) Setup of VDR/SVDR by Maintenance software
(5) Setup of PC in which the VDR/S-VDR Real Time Monitor is installed
(6) Final check
Note
Attention
Attention
Attention
This installation manual is described for version 1.2 of VDR/S-VDR
Real Time Monitor software.
To set up the VDR/S-VDR for VDR/S-VDR Real Time Monitor, use
the latest Maintenance software (Ver. 1.2.0A).
If your Maintenance software is old version, download the latest
version from Marin Service Home Page.
Since the VDR IF (Router) model is changed from AR410 to
AR415S, do not mistake it.
When Radar IF is connected to VDR/S-VDR, VDR IF (Router)
should be connected for separation between Radar IF and user
LAN.
The Firewall of the VDR IF unit is invalidated beforehand at factory
shipment.
If the operation check is completion, the firewall should be
validated.
VDR/S-VDR Real Time Monitor / Installation Manual
1
Chapter1 Installation Procedure
Blank Page
VDR/S-VDR Real Time Monitor / Installation Manual
2
Chapter2 System Composition
Chapter2 System Composition
Since the system configuration is possible various combinations, it explains here by some typical
compositions.
2.1 Basic Composition
Voyage Data
Radar Image
Audio(VHF)
VDR/S-VDR JCY-1800/1850
Capsule
Record
Data
VDR Network
Real Time Monitor
RCU
Fig. 2.1-1
Table 2.1-1 Composition Unit
Number Note
No.
Unit
1.
2.
VDR/S-VDR Real Time Monitor
External HDD
(Moreover one spare is necessary
to collect data for the landside.)
1
2
Standard Windows PC
USB2.0
HDD size is decided according to the record
period and the record contents.
VDR/S-VDR Real Time Monitor / Installation Manual
3
Chapter2 System Composition
2.2 In case of connecting with user LAN
The PCs of each room are connected with user LAN as a monitor terminal, and the system can
be enhanced.
In that case, one Server PC is necessary to deliver data to the Client PCs.
In addition, the number of monitor terminal as Client PC that can be connected with Server PC is
three or less.
VDR/S-VDR JCY-1800/1850
Voyage Data
Radar Image
Audio (VHF)
User LAN
Monitor
Terminal1
(Client)
(Server)
Capsule
VDR Network
Switching
HUB
Record
Data
Real Time Monitor
RCU
Monitor
Terminal2
(Client)
Monitor
Terminal3
(Client)
Fig. 2.2-1
Table 2.2-1 Composition Unit
Number
No.
Unit
1.
VDR/S-VDR Real Time Monitor
(Server)
External HDD
(Moreover one spare is necessary
to collect data for the landside.)
VDR/S-VDR Real Time Monitor
(Client)
Switching HUB
2.
3.
4.
Note
1
Standard Windows PC
2
USB2.0
HDD size is decided according to the record
period and the record contents.
Standard Windows PC
A maximum of three set
For connecting with monitor terminals
3
1
VDR/S-VDR Real Time Monitor / Installation Manual
4
Chapter2 System Composition
2.3 In case of connecting with Radar IF (NWP-46)
In the VDR/S-VDR equipment main Radar image is recorded, and it is possible to capture or
record images of sub Radar, ECDIS and Conning by Radar IF in the VDR/S-VDR Real Time
Monitor.
And, VDR IF (Router) is needed to separate the Radar IF from user LAN.
Voyage Data
Radar Image
Audio
VDR/S-VDR JCY-1800/1850
Radar IF
Capsule
VDR/S-VDR Network
VDR IF
Record
Data
Real Time Monitor
RCU
Fig. 2.3-1
Table 2.3-1 Composition Unit
Number Note
No.
Unit
1.
2.
Real Time Monitor (Server)
External HDD
(Moreover one spare is necessary
to collect data for the landside.)
1
2
Standard Windows PC
USB2.0
HDD size is decided according to the record
period and the record contents.
1
1
For ECDIS Image
Router and HUB functions
In case of addition of option images
1.
2.
Radar IF
VDR IF
VDR/S-VDR Real Time Monitor / Installation Manual
5
Chapter2 System Composition
Blank Page
VDR/S-VDR Real Time Monitor / Installation Manual
6
Chapter3 Wiring Diagrams
Chapter3 Wiring Diagrams
JCY-1800/1850
VDR/S-VDR
EXT-LAN *3
192.168.0.254
RJ-45
*1 Ethernet cable
(Shield Twist-Pair cable)
Max. 30m
192.168.0.251
VDR/S-VDR
Real Time Monitor
PC (*2)
AC
NOTE
1. *1 Shielded LAN Cable(Cat5) : Dock Yard supply
2. *2 PC : Owner supply
3. *3 JCY-1800 : EXT-LAN
JCY-1850 : JRC-LAN
VDR/S-VDR Real Time Monitor INTERCONNECTION DIAGRAM
Fig. 3.1 Basic Composition
VDR/S-VDR Real Time Monitor / Installation Manual
7
Chapter3 Wiring Diagrams
On Board LAN System (Example)
JCY-1800/1850
VDR/S-VDR
HUB
EXT-LAN *3
RJ-45
192.168.0.250
192.168.0.254
LAN
*1 Ethernet cable
(Shield Twist-Pair cable)
Max. 30m
VDR/S-VDR
Real Time Monitor
Client PC1 (*2)
192.168.0.249
VDR/S-VDR
Real Time Monitor
Server PC (*2)
LAN
LAN
VDR/S-VDR
Real Time Monitor
Client PC2 (*2)
AC
192.168.0.248
192.168.0.251
LAN
NOTE
1. *1 Shielded LAN Cable(Cat5) : Dock Yard supply
2. *2 PC : Owner supply
3. *3 JCY-1800 : EXT-LAN
JCY-1850 : JRC-LAN
VDR/S-VDR
Real Time Monitor
Client PC3 (*2)
VDR/S-VDR Real Time Monitor & Onboard LAN (Example) INTERCONNECTION DIAGRAM
Fig. 3.2 In case of connecting with user LAN
VDR/S-VDR Real Time Monitor / Installation Manual
8
Chapter3 Wiring Diagrams
On Board LAN System (Example)
NWP-46
Radar IF
LAN
192.168.111.100
192.168.111.152
WAN
JCY-1800/1850
VDR/S-VDR
VDR IF(Router)
EXT-LAN *3
LAN
RJ-45
192.168.0.254
192.168.0.100
HUB
192.168.0.250
*1 Ethernet cable
(Shield Twist-Pair cable)
Max. 30m
LAN
VDR/S-VDR
Real Time Monitor
Server PC (*2)
VDR/S-VDR
Real Time Monitor
Client PC1 (*2)
LAN
192.168.0.249
AC
192.168.0.251
LAN
NOTE
1. *1 Shielded LAN Cable(Cat5) : Dock Yard supply
2. *2 PC : Owner supply
3. *3 JCY-1800 : EXT-LAN
JCY-1850 : JRC-LAN
VDR/S-VDR
Real Time Monitor
Client PC2 (*2)
192.168.0.248
LAN
VDR/S-VDR
Real Time Monitor
Client PC3 (*2)
VDR/S-VDR Real Time Monitor & Onboard LAN (Example) INTERCONNECTION DIAGRAM
Fig. 3.3 In case of connecting with the Radar Interface (NWP-46)
VDR/S-VDR Real Time Monitor / Installation Manual
9
Chapter3 Wiring Diagrams
Blank Page
VDR/S-VDR Real Time Monitor / Installation Manual
10
Chapter4 Wiring
Chapter 4 Wiring
4.1 In case of JCY-1800 VDR
Open the door of VDR, and connect LAN cables as following.
Maintenance PC:
Connect LAN cable to “VDR-LAN” (Not used port) of MCB.
VDR/S-VDR Real Time Monitor PC:
Connect LAN cable to “EXT-LAN” port of RMB.
Maintenance PC:
VDR－LAN へ
VDR/S-VDR
Real Time Monitor PC：
EXT－LAN へ
VDR/S-VDR Real Time Monitor / Installation Manual
11
Chapter4 Wiring
4.2 In case of JCY-1850 S-VDR
Open the door of S-VDR, and connect LAN cables as following.
Maintenance PC:
Connect LAN cable to “VDR-LAN” (Not used port) of MCB.
VDR/S-VDR Real Time Monitor PC:
Connect LAN cable to “JRC-LAN” port of MCB.
Maintenance PC:
VDR－LAN へ
VDR/S-VDR
Real Time Monitor PC：
JRC－LAN へ
VDR/S-VDR Real Time Monitor / Installation Manual
12
Chapter4 Wiring
4.3 Wiring to VDR IF（Router）
It is necessary to connect VDR IF (Router) for connecting the Radar IF (NWP-46) to
VDR/S-VDR.
VDR/S-VDR
JCY-1800/1850
HUB
Server PC
Radar IF
NWP-46
Client PC
Note
The power cable for the object for AC100 and AC200V is
attached to the VDR IF.
Please connect a power cable according to the supply voltage of
use.
VDR/S-VDR Real Time Monitor / Installation Manual
13
Chapter4 Wiring
RCU upside is recommended as installation place.
To wire AC power cable of the VDR IF, secure 7cm for back space of the VDR IF, and fix it.
【Note】
If the VDR IF is fixed as the following figure, backs space of the VDR IF will be secured 7cm.
In order to fix the VDR IF, please use the attached magic tape in the VDR IF kit.
Magic Tape
Note
In case of reassignment of IP address, in order to correct the
VDR IF setup, please get the VDR IF setting cable by following
code, and set up the VDR IF.
VDR IF Setting Cable：5ZCGF00017
VDR/S-VDR Real Time Monitor / Installation Manual
14
Chapter5 Setup VDR/S-VDR by Maintenance software
Chapter5 Setup VDR/S-VDR by Maintenance software
It is necessary to set real time output setup to VDR/S-VDR by Maintenance software.
The setup way is shown in this chapter.
(1)Click the”JCY1800 Maintenance” icon, and start the maintenance software.
(2)Select “VDR” or “S-VDR” in the Setup Equipment block of Login screen, and log in the software.
In case of JCY-1800: Select VDR
In case of JCY-1850: Select S-VDR
Select VDR or S-VDR.
VDR/S-VDR Real Time Monitor / Installation Manual
15
Chapter5 Setup VDR/S-VDR by Maintenance software
(3)Click the [Option PC(VDR Real Time Monitor)] button in the Home screen.
[Option PC（VDR Real Time Monitor)] button
(4)Click the [Receive] button in the Option screen, and read current setup data.
[Receive] button
VDR/S-VDR Real Time Monitor / Installation Manual
16
Chapter5 Setup VDR/S-VDR by Maintenance software
(5) Check the IP Address of the Option PC and VDR WAN.
VDR WAN ：IP Address of VDR LAN port for connecting the Option PC
Option PC
：Destination IP Address of real time data
If the IP Address is changed, click the [Edit] button, and change it in the Network screen.
Default to
VDR or S-VDR WAN
Option PC
Above is assigned.
= 192.168.0.254
=192.168.0.251
In case of VDR, Network screen）
In case of S-VDR, Network screen）
Note
If input is mistaken, the IP Addresses become initial value by the
[Default] button.
Note
If the [Set] button is clicked, the VDR/S-VDR is rebooted
automatically to validate the input IP Address.
VDR/S-VDR Real Time Monitor / Installation Manual
17
Chapter5 Setup VDR/S-VDR by Maintenance software
(6) Input check for real time output of necessary data.
Every data can be selected, and moreover all output can be set up by package with the [All Enable]
button and [All Disable] button.
[All Enable]: “✓” is entered by package in check box of all the data which is possible to out.
[All Disable]: “✓” is removed by package in check box of all the data which is possible to out.
[All Enable]/
[All Disable]
Button
(7) Make sure the setup, and click the [Set] button.
Maintenance software sends the setup data, and then reboots VDR/S-VDR automatically.
[Set] button
(8) If the maintenance software logs in VDR/S-VDR after restart, the setup for VDR/S-VDR Real Time
Monitor is completion.
(9) Click the [Logout] button, and quit the Maintenance software.
VDR/S-VDR Real Time Monitor / Installation Manual
18
Chapter6 PC (Server/Client) Setup
Chapter6 PC (Server/Client) Setup
6.1 PC Specification
Confirm that the specification of an installed PC is the following performance equivalent model.
OS
CPU
RAM
HDD
Resolution
CD drive
Card drive
Network
:
:
:
:
:
:
:
:
Windows XP Professional or Home Edition
Pentium M Processor 730 Clock=1.6GHz
512MB
40GB
1024×1024 dots (More than XGA)
CD-ROM
PCMCIA TypeⅡ or CF Card drive
10BASE-T/100BASE-TX Ethernet
6.2 Setup Items of PC
In order to prevent sending unnecessary packets to the network that includes the VDR/S-VDR
from the VDR/S-VDR Real Time Monitor PC, set the following items to a PC.
And also set the IP address to the PC.
・
・
・
・
・
・
・
Set the IP address
Stop automatic synchronization with an Internet time server
Stop the Remote Assistance
Stop the Automatic Updates
Stop the Error Reporting
Invalidate the Windows Firewall
Set the Power Options
6.2.1 Set the IP address
Set the IP address to the installed PC.
Shows the assignment of the IP addresses in Table 6.2-1.
Mode
IP Address
※1
Table 6.2-1 IP address
Subnet Mask
Default Gateway
※1
255.255.255.0
Unnecessary
Server
192.168.0.251
255.255.255.0
Unnecessary
Client1
192.168.0.250※1
255.255.255.0
Unnecessary
Client2
192.168.0.249※1
※1
255.255.255.0
Unnecessary
Client3
192.168.0.248
※1：Even if IP Address already is assigned to Server PC and Client PC by user LAN,
please add to registration of the above IP Address.
If the IP address automatically is assigned by DHCP in the user LAN, cancel the
DHCP. And register an unused fix IP address in the user LAN and add above IP
address.
Refer to "9.2 Example of connection" for more detail.
VDR/S-VDR Real Time Monitor / Installation Manual
19
Chapter6 PC (Server/Client) Setup
(1) Click the “Network and Internet Connections” in the Control Panel screen.
Network and Internet
Connections
(2) Click the “Network Connections”.
Network Connections
(3) Right-click the “Local Area Connection”, and select the Properties menu.
VDR/S-VDR Real Time Monitor / Installation Manual
20
Chapter6 PC (Server/Client) Setup
(4) Select the “Internet Protocol (TCP/IP)”, and click the [Properties] button.
(5) Enter the IP address and the Subnet mask, and click the [OK] button.
If the IP address which is different from default is already assigned in the user LAN, click
the [Advance] button and go to (6).
And Add registration of the IP address shown in the Table 6.2-1 to the Server or Client
PC.
[Advance] button
VDR/S-VDR Real Time Monitor / Installation Manual
21
Chapter6 PC (Server/Client) Setup
(6) Register the IP address shown in the Table 6.2-1.
IP address
Server=192.168.0.251
Client1=192.168.0.250
Client2=192.168.0.249
Client3=192.168.0.248
The IP address setup is completion.
VDR/S-VDR Real Time Monitor / Installation Manual
22
Chapter6 PC (Server/Client) Setup
6.2.2 Stop automatic synchronization with an Internet time server
Shows how to stop automatic synchronization with an Internet time server.
(1) Click the clock indication at the lower right of a screen.
(2) The “Date and Time Properties” screen is indicated, and select the “Internet Time” tab.
(3) Remove the “Automatically synchronize with an Internet time server” check, and click the
[OK] button.
The automatic synchronization is stopped.
VDR/S-VDR Real Time Monitor / Installation Manual
23
Chapter6 PC (Server/Client) Setup
6.2.3 Stop the Remote Assistance
(1) Click the “Performance and Maintenance” in the Control Panel screen.
Performance and
Maintenance
(2) Click the “System”.
System
VDR/S-VDR Real Time Monitor / Installation Manual
24
Chapter6 PC (Server/Client) Setup
(3) Select the Remote tab.
(4) Remove the “Remote Assistance” check, and click the [OK] button.
The Remote Assistance is stopped.
VDR/S-VDR Real Time Monitor / Installation Manual
25
Chapter6 PC (Server/Client) Setup
6.2.4 Stop the Automatic Updates
(1) Click the “Performance and Maintenance” in the Control Panel screen.
Performance and
Maintenance
(2) Click the “System”.
System
VDR/S-VDR Real Time Monitor / Installation Manual
26
Chapter6 PC (Server/Client) Setup
(3) Select the Automatic Updates tab.
(4) Select the “Turn off Automatic Updates”, and click the [OK] button.
The Automatic Updates is stopped
VDR/S-VDR Real Time Monitor / Installation Manual
27
Chapter6 PC (Server/Client) Setup
6.2.5 Stop the Error Reporting
(1) Click the “Performance and Maintenance” in the Control Panel screen.
Performance and
Maintenance
(2) Click the “System”.
System
VDR/S-VDR Real Time Monitor / Installation Manual
28
Chapter6 PC (Server/Client) Setup
(3) Select the “Advanced” tab.
(4) Click the [Error Reporting] button.
[Error Reporting] button
VDR/S-VDR Real Time Monitor / Installation Manual
29
Chapter6 PC (Server/Client) Setup
(5) Select the “Disable error reporting”, and remove the “But notify me when critical errors
occur” check. And click the [OK] button.
(6) Click the [OK] button, and close the System Properties screen.
The Error Reporting” is stopped.
VDR/S-VDR Real Time Monitor / Installation Manual
30
Chapter6 PC (Server/Client) Setup
6.2.6 Invalidate the Windows Firewall
The setup screen for the Windows Firewall changes with versions of Service Pack of Windows
XP. Invalidate the Firewall after confirming version of Service Pack.
Note
It is possible to confirm version of Service Pack by the following
operations.
･Right-click the My Computer, and select the Properties menu.
･ Select the System in order of the Control Panel -> the
Performance and Maintenance.
6.2.6.1 In case of Service Pack1
(1) Click the “Network and Internet Connections” in the Control Panel screen.
Network and Internet
Connections
(2) Click the “Network Connections”.
Network Connections
VDR/S-VDR Real Time Monitor / Installation Manual
31
Chapter6 PC (Server/Client) Setup
(3) Right-click the “Local Area Connection”, and select the Properties menu.
(4) Select the Advanced tab, and remove the Windows Firewall check.
The Firewall is invalidated.
VDR/S-VDR Real Time Monitor / Installation Manual
32
Chapter6 PC (Server/Client) Setup
6.2.6.2 In case of Service Pack2
(1) Click the “Network and Internet Connections” in the Control Panel screen.
Network and Internet
Connections
(2) Click the Windows Firewall.
Windows Firewall
VDR/S-VDR Real Time Monitor / Installation Manual
33
Chapter6 PC (Server/Client) Setup
(3) The Windows Firewall screen is indicated, and select “Off (Not recommended)”, and click
the [OK] button.
The Firewall is invalidated.
VDR/S-VDR Real Time Monitor / Installation Manual
34
Chapter6 PC (Server/Client) Setup
6.2.7 Set the Power Options
In case of Server PC, it is necessary to prevent a system standby, a system hibernation, etc
during employment.
(1) Click the “Performance and Maintenance” in the Control Panel screen.
Performance
and
Maintenance
(2) Click the “Power Options”
Power Options
VDR/S-VDR Real Time Monitor / Installation Manual
35
Chapter6 PC (Server/Client) Setup
(3) Select “Never” in the all items of the “Turn off hard disks”, the “System Standby” and the
“System hibernates”, and click the [OK] button.
The Power Options setup is completion.
VDR/S-VDR Real Time Monitor / Installation Manual
36
Chapter6 PC (Server/Client) Setup
6.3 Install the VDR/S-VDR Real Time Monitor software
Install the VDR/S-VDR Real Time Monitor software in a PC in accordance with the following
operation.
(1) Insert the Install CD-ROM in a CD drive.
(2)After a while, Installer starts and the following web screen opens automatically by
AUTORUN.
(3)To continue installation, please operate from (4).
(If the installer does not start, click “SetupE.exe” after selecting the CD drive by My
Computer. And then operate from (3).)
Note
The following contents are possible to refer in the web screen.
・ VDR/S-VDR Real Time Monitor instruction manual
・ CSV Conversion instruction manual
・ CD license number
VDR/S-VDR Real Time Monitor / Installation Manual
37
Chapter6 PC (Server/Client) Setup
(4) The installer for the VDR Real Time Monitor starts, and the preparation for the installation
is started.
(5) The opening screen is indicated, and click the [Next] button.
(6) The InstallShield Wizard for the VDR Real Time Monitor starts, and click the [Next] button.
VDR/S-VDR Real Time Monitor / Installation Manual
38
Chapter6 PC (Server/Client) Setup
(7) Customer Information screen is indicated.
Please enter user information in the User Name field and the Organization field.
And enter the License number which is described in the Real Time Monitor of the Web
screen to the Serial Number field, and click the [Next] button.
Note
License number is composed by ”JRC－＊＊＊＊－＊＊＊＊”.
The number is displayed in the place of “The license number for
Real Time Monitor is as follows:” of the install CD-ROM.
“The license number
License Number
for Real Time Monitor
is as follows:”
(8) The confirmation screen where the installation folder and user information are shown is
displayed, and click the [Install] button.
VDR/S-VDR Real Time Monitor / Installation Manual
39
Chapter6 PC (Server/Client) Setup
(9) Install is started, and progress bar is indicated.
(10) Click the [Server] button or the [Client] button in accordance with the content shown in
the "6.2.1 IP address Setup".
(11) The InstallShield Wizard completion screen is indicated, and click the [Finish] button.
Installation of the VDR/S-VDR Real Time Monitor software is completion.
Please eject the Install CD-ROM from the CD drive, and keep the Installation CD-ROM
carefully.
VDR/S-VDR Real Time Monitor / Installation Manual
40
Chapter6 PC (Server/Client) Setup
6.4 Uninstall the VDR/S-VDR Real Time Monitor software
To uninstall the VDR/S-VDR Real Time Monitor software, operate as follows.
(1) Click the “Add or Remove Programs” in the Control Panel screen.
(2) Select the “JCY-1800 VDR_Monitor”, click the [Remove] button.
(3) Since some files are remained in the installation folder, remove the folder with the My
Computer.
Installation Folder: C:\Program files\JRC\JCY1800\VDR_Monitor
VDR/S-VDR Real Time Monitor / Installation Manual
41
Chapter6 PC (Server/Client) Setup
6.5 Initial setup for the VDR/S-VDR Real Time Monitor
Initial setup for the VDR/S-VDR Real Time Monitor is set up with the Setup software of
VDR/S-VDR Real Time Monitor software attachment. Shows the setup flow.
Server and Client PC)
(1) VDR/S-VDR configuration reading by communication
(2) Various setups
Completion
The necessary items of initial setup are as follows
Table 6.2 Setup Item
PC
Setup
Tab Name
Server
Setup of equipment connections
Recording ON/OFF
Setup of recording folder
Setup of recording period
Assignment of Client PC IP address
Check quantity of Engine, Rudder, Thruster,
Propeller and Keel – Trans.
Note: The data are set by Maintenance software.
If the data is wrong, setup the data by
Maintenance software again.
System tab
Client
Setup of equipment connections
Check quantity of Engine, Rudder, Thruster,
Propeller and Keel – Trans.
Note: The data are set by Maintenance software.
If the data is wrong, setup the data by
Maintenance software again.
Note
Ethernet tab
Configuration tab
System tab
Configuration tab
The inputs to the unnecessary items in the setup items of Server
and Client are prevented.
VDR/S-VDR Real Time Monitor / Installation Manual
42
Chapter6 PC (Server/Client) Setup
6..5.1 Setup
Please initialize in accordance with the following operations.
(1) Click the [Setup] button in the VDR Launcher.
(2) Select the “Serviceman”, and log in after inputting serviceman information and the
following password.
Password:“jrcvdr”（Input everything by the small letter.）
VDR/S-VDR Real Time Monitor / Installation Manual
43
Chapter6 PC (Server/Client) Setup
(3) Reading of the VDR configuration.
Server and Client PC）
Eject a CF card from VDR/S-VDR, and insert it into the CF card slot of used PC.
Then, to import VDR/S-VDR configuration data, select the “SysInfo.dat” file in the
CF card and click the [Import] button. CF card drive changes with PC of use.
Caution
When a CF card is ejected from the VDR/S-VDR, please be sure
to follow the operation of “9.1 How to eject CF card from
VDR/S-VDR”.
The CF card may be damaged and record may not be available.
*:\Init\SysInfo.dat
CF card drive
Import button
VDR/S-VDR Real Time Monitor / Installation Manual
44
Chapter6 PC (Server/Client) Setup
Blank Page
VDR/S-VDR Real Time Monitor / Installation Manual
45
Chapter6 PC (Server/Client) Setup
(4) Input the necessary items in the System tab.
Refer to the Table6.3 for setup contents.
①
②
③
④
⑤
⑥
⑦
⑧
⑨
VDR/S-VDR Real Time Monitor / Installation Manual
46
Chapter6 PC (Server/Client) Setup
Table6.3 Setup Contents in the System Tab
No.
Block
Content
①
Sensor
Existing of A/D and Dry Contact is indicated. If the unit exists,
“✓”
is
Setup*1
Note
U
The
displayed.
contents
gotten
from the VDR configuration.
②
③
Audio
Visual
Monitor
To monitor audio, input “✓”.
Record
To record audio, input
Connect
Select a connection type.
Record
To record the image, input “✓”.
Connection,
Input the model of equipment whose image is
next page for more
captured
detail.
Model
Maker
N
“✓”.
N
Serial No.
the
refer
to
In case of FGB1, the
contents gotten from
Input the Serial Number of equipment whose images
the VDR configuration.
is captured.
Terminal
select
Input the maker of equipment whose images is
captured.
④
To
If the Client PC of the VDR/S-VDR Real Time Monitor exists, input “✓”.
N
To distribute to Client
PC, it is necessary to
Do not select the Broadcast. PCs in user LAN other than the VDR/S-VDR
set
Real Time Monitor may be influenced.
address in the Ethernet
Client
PC
IP
tab.
⑤
Setup Folder
For
The usage of the selected folder is shown either for
U
playback-only or record & playback by the mode.
When
there
is
record
mode
mode,
or
Folder
Select a folder for playback and record.
N
playback
Ship’s Name
Ship's Name and IMO number registered in the VDR
U
inputs to the items are
IMO No.
configuration data are displayed.
[Initialize] button
The selected folder is initialized.
N
PC Card Drive
Drive
Select a drive of CF card with the button.
N
⑦
System Files
[Default] button
If the system files are broken, the files are repaired.
U
⑧
Record
Overwrite
To continue to record by overwrite after passing the
N
record period, input “✓”.
When there is not
“✓”
Period
When
there
is
to
and the record period is
the
items
prevented.
Input the record period.
N
HDD Free
It is a limitation value of the HDD free space to
U
Space Limit
prevent all space being used by the recording. The
value is fixed with 1GB, and can not change it.
Time to Warning
It is a timer value for indicating the warning screen
after
when record is paused.
Record
Stop
The time is fixed with one hour, and can not change it.
Time
Source Data
It is a source data for time correction.
Correction
Adjustment
It is an adjustment value for time correction.
U
U
The time is fixed with 500 milliseconds, and can not
change it.
*1: N: Necessary, U: Unnecessary
VDR/S-VDR Real Time Monitor / Installation Manual
47
no
record mode, the inputs
passed, the record is stopped automatically.
Record
the
prevented.
⑥
⑨
not
are
Chapter6 PC (Server/Client) Setup
Explains how to set up the Visual block.
Connection）
Set the connection type of Radar unit.
Shows the detail of connection type the following table so that select a type and set.
Connection
Connection Type
FGB1（VDR）
※Built in VDR
FGB2（Option）
※Radar IF(NWP-46)
None
－
－
None connection to Radar
Case1
Radar1
－
Case2
Radar1
Radar3
Case3
Radar1
Radar3＋Radar4
Radar1（X-Band）
Assume connection of above unit.
・Radar1（X-Band）
・Radar3（ECDIS）
Assume connection of above unit.
・Radar1（X-Band）
・Radar3（ECDIS）
・Radar4（Other Image）
Assume connection of above unit.
Case4
Radar1＋Radar2
－
Case5
Radar1＋Radar2
Radar3
Case6
Radar1＋Radar2
Radar3＋Radar4
Connection
Note
VDR/S-VDR Real Time Monitor / Installation Manual
48
・Radar1（X-Band）
・Radar2（S-Band）
Assume connection of above unit.
・Radar1（X-Band）
・Radar2（S-Band）
・Radar3（ECDIS）
Assume connection of above unit.
・Radar1（X-Band）
・Radar2（S-Band）
・Radar3（ECDIS）
・Radar4（Other Image）
Assume connection of above unit.
Chapter6 PC (Server/Client) Setup
FGB1（VDR））
If the FGB1(VDR) is clicked, information of FGB1 built in VDR is displayed.
Not need the input since the information is displayed by the imported VDR configuration file.
FGB1 (VDR)
Radar1/Radar2）
If the Radar1 or Radar2 is clicked, information of the clicked Radar (which is recorded by VDR) is
displayed.
Not need the input since the information is displayed by the imported VDR configuration file.
To record the Radar image, input “✓” in the Record check box of Radar1 and Radar2.
Ex. Connection is Case4.
Radar1
Record
/Radar2
FGB2（Option））
If the FGB2 is clicked, the input screen for the Radar IF information is displayed.
Refer to the input example, and input the information.
Ex.
・Connection
・Model
・Maker
・Serial No
：Case5
：NWP-46
：JRC
：MBXXXXX
FGB2
(Option)
VDR/S-VDR Real Time Monitor / Installation Manual
49
Chapter6 PC (Server/Client) Setup
Radar3/Radar4）
If the Radar3 or Radar4 is clicked, information of the clicked Radar (which is not recorded by VDR) is
displayed.
Refer to the input example, and input the information.
To record the Radar image, input “✓” in the Record check box of Radar3 and Radar4.
Ex.
・Connection
・Model
・Maker
・Serial No
：Case5
：JAN－701
：JRC
：KEXXXXX
Record
VDR/S-VDR Real Time Monitor / Installation Manual
50
Chapter6 PC (Server/Client) Setup
Blank Page
VDR/S-VDR Real Time Monitor / Installation Manual
51
Chapter6 PC (Server/Client) Setup
(5) It is not necessary to change the Ethernet tab normally.
Refer to the Table 6.4 for more detail.
①
②
③
④
⑤
⑥
VDR/S-VDR Real Time Monitor / Installation Manual
52
Chapter6 PC (Server/Client) Setup
Table6.4 Setup Contents in the Ethernet Tab
No.
Block
Content
Setup*1
①
Option PC
LAN1 (VDR Side)
It is the IP address for communication with the
Note
U
VDR.
LAN2 (Terminal Side)
It is the IP address for connecting with Client
N
PC in the user LAN.
Please change the IP address in accordance
②
VDR IF
（Router）
WAN（FGB2 Side）
with the user LAN allocation.
In case of connecting the VDR IF, please check
to the Connect
It is the IP address of Radar IF connection side.
N
LAN （ Real
It is the IP address of Client PC connection
N
Connect
Time
Monitor Side）
③
side.
FGB
IP Address
It is the Radar IF IP address.
(Visual)
for Real Time Monitor
It is the port for receiving real time monitor data.
Option PC
N
N
It is the port number for communicating with the
Radar IF.
FGB
④
Terminal
It is the port number of Radar IF side.
It is the IP addressed of the monitor terminals
U
N
Check mark of connection is needed in the Terminal block of the System
tab.
⑤
Network
[Connect]
To connect LAN and use, click the [Connect]
Connection
U
button.
[Disconnect]
To disconnect LAN and use as following, click
the [Disconnect] button.
･ In case of disconnecting a LAN cable and
playback in somewhere else
⑥
VDR
Shows the VDR network composition.
Network
They are reference only.
U
*1: N: Necessary, U: Unnecessary
Note
In case of client, the setup of the Ethernet tab is unnecessary to
change.
VDR/S-VDR Real Time Monitor / Installation Manual
53
Chapter6 PC (Server/Client) Setup
(6) Check the quantity of engine, rudder, thruster and propeller, Trans-Keel and sentence
from sensors in the Configuration tab.
Quantity
Note
If a setup content is wrong, the VDR/S-VDR Real Time Monitor can
not indicate a data correctly of the wrong content.
Please set the wrong setup correctly by the Maintenance software.
VDR/S-VDR Real Time Monitor / Installation Manual
54
Chapter6 PC (Server/Client) Setup
Note
About Keel – Trans
It means distance from keel to transducer as the following figure.
Echo sounder outs depth under transducer, so that depth under
keel can be indicated always by registration the distance.
(7) Set the inputted contents
In case of Server PC）
Click the [All Set] button to setup.
The initial setup for Server PC is completion.
If the Clients are connected, please continue the initial setup for Client PC in a monitor
terminal.
In case of Client PC)
Click the [All Set] button to setup.
(8) When setup is completion after clicking the [All Set] button, click the [Close] button to
close the Setup software.
Note
When the [All Set] button is clicked, folder composition and system
files in the selected folder for record and playback are checked.
By the result, when it is necessary to initialize, the following screen
is indicated. Click the [OK] button to close the screen, and then click
the [Initialize] button which is in the Setup Folder block of the
System tab to initialize the folder.
VDR/S-VDR Real Time Monitor / Installation Manual
55
Chapter6 PC (Server/Client) Setup
(9) Return the CF card to the VDR/S-VDR.
Caution
When data copying is finished, please be sure to insert a CF card
to the VDR/S-VDR.
If the CF card is continued to eject more than 10 minutes, “MEDIA”
alarm occurs in the VDR/S-VDR.
Setup is completion above.
VDR/S-VDR Real Time Monitor / Installation Manual
56
Chapter7 Final Check
Chapter7 Final Check
When the installation is completion, start the VDR Real Time Monitor by the [MONITOR] button
of the VDR_Launcher.
Please check the operation of the VDR/S-VDR Real Time Monitor in accordance with the
checklist of the Table 7.1.
When the VDR/S-VDR Real Time Monitor is installed with the record function, in order to prevent
record missing, the Back Up screen is indicated at opening.
But when the VDR/S-VDR Real Time Monitor is installed without the record function, the
VDR/S-VDR Real Time Monitor screen is indicated without the Back Up screen.
Backup button
VDR Real Time Monitor / Installation Manual
57
Chapter7 Final Check
Table 7.1 Checklist for the VDR Real Time Monitor
VDR Real Time Monitor
Item
Content
Judgment
Server Client1 Client2 Client3
Real time
indication
Is the indication of sensor data possible?
Is the audio monitoring possible?
Is the monitor prevented depending on a customer
demand?
Is the indication of the FGB1 image possible?
Is the indication of the FGB2 image possible?
Record
function
Are the sensor files saved in the specified folder?
Are the audio files saved in the specified folder?
Is the record prevented depending on a customer
demand?
Are the FGB1 image files saved in the specified
folder?
Is the record prevented depending on a customer
demand?
Are the FGB2 image files saved in the specified
folder?
Is the record prevented depending on a customer
demand?
Is the record period right?
Is the free space in the HDD enough more than the
record period?
Is the indication of sensor data possible?
Is the audio monitoring possible?
Is the indication of the FGB1 image possible?
Is the indication of the FGB2 image possible?
Playback
function
VDR/S-VDR Real Time Monitor / Installation Manual
58
Chapter8 Trouble Shooting
Chapter8 Trouble Shooting
Table8.1
In case of Server
No.
Symptom
1
The real time indication is not Faulty wiring of a LAN cable
possible.
Initial setup for real time
output is not completed by
the Maintenance software
yet.
Cause
Action
2
The image indication is not The Power of a captured Turn on power of a captured
possible.
display is not turned on.
display.
3
There are no audio outputs of Audio monitoring
the real time.
validated.
4
The record is not possible.
5
The audio recording is not
possible.
6
The image recording is not
possible
7
Record data are less than a
record period.
8
When a LAN cable of the VDR
Real
Time
Monitor
is
disconnected, it is not possible
to playback.
Check the connections.
Set the Option PC setup by the
Maintenance software.
⇒Refer to Chapter 5.
is
not Validate audio monitoring by
the Setup software.
⇒Refer to Table 6.5-2.
Audio volume of the VDR Adjust the Volume or invalidate
Real Time Monitor is low.
the Mute.
Or mute is validated.
Audio volume of the Windows Adjust the Volume or invalidate
the Mute in the “Volume
or is low.
Control” and “Wave”.
Or mute is validated.
Faulty wiring of the external Check the connections.
HDD
The power of the external Turn on the power of the
HDD power is not turned on. external HDD.
The audio recording is not Validate the record by the
necessary.
Setup software.
⇒Refer to Table 6.5-2.
The image recording is not Validate the record by the
necessary.
Setup software.
⇒Refer to Table 6.5-2.
The free space of the HDD is Increase a free space by
not enough for the record deleting unnecessary data, or
period.
exchange to a mass HDD
The [Connect] button is In order to operate under
pressed and operation is in disconnecting the LAN, please
the state of LAN connection.
press the [Disconnect] button in
the Setup software.
⇒Refer to Table 6.5-3.
VDR Real Time Monitor / Installation Manual
59
Chapter8 Trouble Shooting
Table6-2
In case of Client (Monitor Terminal)
No.
Symptom
1
The real time indication is not Faulty wiring of a LAN cable
possible.
The IP address setup of the
terminal by the Server side is
wrong.
Cause
Action
Check the connections.
Correct the IP address of the
terminal by the Setup software
of the Server side.
⇒Refer to Table 6.5-3.
There are no checks of Input the check of the terminal
terminal connections by the Connection by the Setup
Server side.
software of the Server side.
⇒Refer to Table 6.5-2.
VDR/S-VDR Real Time Monitor / Installation Manual
60
Chapter9 Appendix
Chapter9 Appendix
9.1 How to eject CF card from VDR/S-VDR
(1) Push the [CARD STOP] button.
(2) The CARD LED blinks for 5 sec and goes out. Then ejection of CF card becomes possible.
(3) Push the [EJECT] button, and eject a CF card.
CF card Slot
EJECT button
CARD LED（Green）
CARD STOP button
Note
In both VDR and S-VDR, CF card can be ejected with same
operation.
VDR Real Time Monitor / Installation Manual
61
Chapter9 Appendix
Blank Page
VDR/S-VDR Real Time Monitor / Installation Manual
62
case
by
of
with user LAN
connecting
network
designing
In
In case of registration by adding
Note
information to Mitaka.
63
Code No. (VDR IF setup cable)：5ZCGF00017
the VDR IF.
Please get the setup cable by the following code number, and set up
script file of VDR IF.
If IP address assignment is changed, it is necessary to change the
In case of connecting with Client PC and Radar IF
VDR Real Time Monitor / Installation Manual
Use
changed, please feed back the
Connect
Example 7
If IP address assignments are
If the IP address automatically
is assigned by DHCP in the
user LAN, cancel the DHCP.
And register an unused fix IP
address in the user LAN and
add above IP address.
In case of connecting with Client PC
－
－
－
Example 6
－
Connect
－
－
Note
default IP address to PC
In case of connecting with Client PC and Radar IF
Example 5
In case of connecting with Client PC
Example 4
Connect
－
－
for VDR IF
Setup cable
In case of registration by changing
default IP address to PC
Example 3
from user LAN
In case of connecting with Client PC and Radar IF
In case of connecting with Client PC
separating
network
Example 2
In case of only one VDR/S-VDR Real Time Monitor
by
－
Example1
address to PC
of
In case of registering default IP
designing
case
In
VDR IF
Connection
and Client PC
Connection
Example of Connection
IP address assignment of Server
User LAN
Shows how to set according to example of connection.
9.2 Example of connection
Chapter9 Appendix
VDR/S-VDR Real Time Monitor / Installation Manual
Chapter9 Appendix
64
Blank Page
Chapter9 Appendix
9.2.1 Example1 In case of only one VDR/S-VDR Real Time Monitor
Explains how to set PC as stand-alone VDR/S-VDR Real Time Monitor PC.
Please register default IP address to the VDR/S-VDR Real Time Monitor PC.
JCY-1800/1850
VDR/S-VDR
EXT-LAN *3
192.168.0.254
RJ-45
*1 Ethernet cable
(Shield Twist-Pair cable)
Max. 30m
192.168.0.251
VDR/S-VDR
Real Time Monitor
PC (*2)
AC
NOTE
1. *1 Shielded LAN Cable(Cat5) : Dock Yard supply
2. *2 PC : Owner supply
3. *3 JCY-1800 : EXT-LAN
JCY-1850 : JRC-LAN
VDR/S-VDR Real Time Monitor INTERCONNECTION DIAGRAM
VDR Real Time Monitor / Installation Manual
65
Chapter9 Appendix
STEP 1
Set by Maintenance software
(1)Open the Option PC（VDR Real Time Monitor）screen
(2)Click the [All Enable] button
(3)Check that the following addresses in VDR WAN and Option PC
・ VDR WAN=192.168.0.254
・ Option PC=192.168.0.251
VDR WAN
/Option PC
[All Enable]
button
(4) If the IP address is different, open the Network screen by the [Edit] button, and change IP
address.
When the [Default] button is clicked, default IP addresses are input.
[Default] button
(5) Click the [Set] button.
Setting by the Maintenance software is completion above.
After this, operate on the VDR/S-VDR Real Time Monitor.
VDR/S-VDR Real Time Monitor / Installation Manual
66
Chapter9 Appendix
STEP 2
Set IP Address
Open the properties screen of Internet protocol (TCP/IP) in the Windows control panel, and set
the following IP address to the VDR/S-VDR Real Time Monitor PC.
・IP Address
=192.168.0.251
・Subnet Mask
=255.255.255.0
It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor.
IP Address
/Subnet Mask
And then set the VDR/S-VDR Real Time Monitor PC in accordance with the “6.2 Setup Items of
PC”.
STEP 3
Install the VDR/S-VDR Real Time Monitor software
Install the VDR/S-VDR Real Time Monitor software with the install CD.
When the Server/Client selection screen displayed, please select Server.
VDR Real Time Monitor / Installation Manual
67
Chapter9 Appendix
STEP 4
Set by the Setup software
(1) System tab screen
・ Input “✓” when monitor or record in the Audio block is needed.
・ Input “✓” when connection or record in the FGB block is needed, and input the Radar
information.
・ Select the record folder when the VDR/S-VDR Real Time Monitor PC records.
・ Set record period in the Record block when recording.
Audio
FGB
Folder
Record
VDR/S-VDR Real Time Monitor / Installation Manual
68
Chapter9 Appendix
(2) Ethernet tab screen
Check that the following IP address is set.
・LAN1(VDR Side)=192.168.0.251
・VDR IF(Router) Connect=None
192.168.0.251
None
(3) Click the [All Set] button, and setting of the VDR/S-VDR Real Time Monitor is completion.
VDR Real Time Monitor / Installation Manual
69
Chapter9 Appendix
9.2.2 Example2 In case of connecting with Client PC
IP address assignment of Server and Client PC is default, and explains how to set when Server
PC is connected to Client 1, Client 2 and Client3 PC.
On Board LAN System (Example)
JCY-1800/1850
VDR/S-VDR
EXT-LAN *3
HUB
192.168.0.254
192.168.0.250
RJ-45
LAN
*1 Ethernet cable
(Shield Twist-Pair cable)
Max. 30m
192.168.0.249
VDR/S-VDR
Real Time Monitor
Server PC (*2)
192.168.0.251
VDR/S-VDR
Real Time Monitor
Client PC1 (*2)
LAN
LAN
VDR/S-VDR
Real Time Monitor
Client PC2 (*2)
AC
192.168.0.248
LAN
NOTE
1. *1 Shielded LAN Cable(Cat5) : Dock Yard supply
2. *2 PC : Owner supply
3. *3 JCY-1800 : EXT-LAN
JCY-1850 : JRC-LAN
VDR/S-VDR
Real Time Monitor
Client PC3 (*2)
VDR/S-VDR Real Time Monitor & Onboard LAN (Example) INTERCONNECTION DIAGRAM
VDR/S-VDR Real Time Monitor / Installation Manual
70
Chapter9 Appendix
STEP 1
Set by Maintenance software
(1)Open the Option PC（VDR Real Time Monitor）screen.
(2)Click the [Receive] button to receive the VDR/S-VDR configuration data.
(3)Click the [All Enable] button.
(4)Check that the following addresses in VDR WAN and Option PC.
・ VDR WAN=192.168.0.254
・ Option PC=192.168.0.251
VDR WAN
/Option PC
[All Enable]
button
(5) If the IP address is different, open the Network screen by the [Edit] button, and change IP
address.
When the [Default] button is clicked, default IP addresses are input.
[Default] button
(6) Click the [Set] button.
Setting by the Maintenance software is completion above.
After this, operate on Server PC of the VDR/S-VDR Real Time Monitor.
VDR Real Time Monitor / Installation Manual
71
Chapter9 Appendix
STEP 2 Set IP Address of Server PC
Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and set
the following IP address to the Server PC.
・IP Address
=192.168.0.251
・Subnet Mask
=255.255.255.0
It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor.
IP Address
/Subnet Mask
And then set the Server PC in accordance with the “6.2 Setup Items of PC”.
VDR/S-VDR Real Time Monitor / Installation Manual
72
Chapter9 Appendix
STEP 3 Set by the Setup software of Server PC
Install the VDR/S-VDR Real Time Monitor software in accordance with “9.4 Install Flow for
Server PC”, and set by the Setup software.
(1) System tab screen
・ Input “✓” when monitor or record in the Audio block is needed.
・ Input “✓” when connection or record in the FGB block is needed, and input the Radar
information.
・ Input “✓” to Terminal 1, 2 and 3 in Terminal block since there are 3 Client PCs.
・ Select the record folder when the VDR/S-VDR Real Time Monitor PC records.
・ Set record period in the Record block when recording.
Audio
FGB
Terminal
Folder
Record
VDR Real Time Monitor / Installation Manual
73
Chapter9 Appendix
(2)Ethernet tab screen
Check that the following IP address is set.
・LAN1(VDR Side)=192.168.0.251
・VDR IF(Router) Connect=None
192.168.0.251
None
(3) Click the [All Set] button, and setting of the Server PC is completion.
VDR/S-VDR Real Time Monitor / Installation Manual
74
Chapter9 Appendix
STEP 4
Set IP Address of Client PC
Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and set
the following IP address to the Client PC.
・IP Address
Client1=192.168.0.250
Client2=192.168.0.249
Client3=192.168.0.248
・Subnet Mask
=255.255.255.0
It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor.
IP Address
/Subnet Mask
And then set the Client PC in accordance with the “6.2 Setup Items of PC”.
VDR Real Time Monitor / Installation Manual
75
Chapter9 Appendix
STEP 5
Set by the Setup software of Client PC
Install the VDR/S-VDR Real Time Monitor software in accordance with “9.5 Install Flow for Client
PC”, and set by the Setup software.
(1)System tab screen
・ Input “✓” when monitor or record in the Audio block is needed.
・ Input “✓” when connection or record in the FGB block is needed, and input the Radar
information.
・ Select the record folder when the VDR/S-VDR Real Time Monitor PC records.
・ Set record period in the Record block when recording.
Audio
FGB
Folder
Record
VDR/S-VDR Real Time Monitor / Installation Manual
76
Chapter9 Appendix
(2)Ethernet tab screen
There is no setup in the Ethernet tab screen.
(3)Click the [All Set] button, and setting of the Client PC is completion.
Please set up other Client PC similarly.
VDR Real Time Monitor / Installation Manual
77
Chapter9 Appendix
9.2.3 Example3 In case of connecting with Client PC and Radar IF
IP address assignment of Server and Client PC is default, and explains how to set when Server
PC is connected to Client 1, Client 2, Client3 PC and Radar IF.
Note
Radar IF (NWP-46)
In the VDR/S-VDR equipment main Radar image is captured
and recorded, and it is possible to capture or record images of
sub Radar and ECDIS by the Radar IF in the VDR/S-VDR Real
Time Monitor.
On Board LAN System (Example)
LAN
NWP-46
Radar IF
192.168.111.152
WAN
192.168.111.100
JCY-1800/1850
VDR/S-VDR
VDR IF(Router)
EXT-LAN *3
LAN
RJ-45
192.168.0.254
192.168.0.100
HUB
192.168.0.250
*1 Ethernet cable
(Shield Twist-Pair cable)
Max. 30m
LAN
VDR/S-VDR
Real Time Monitor
Server PC (*2)
192.168.0.251
VDR/S-VDR
Real Time Monitor
Client PC1 (*2)
LAN
192.168.0.249
AC
LAN
NOTE
1. *1 Shielded LAN Cable(Cat5) : Dock Yard supply
2. *2 PC : Owner supply
3. *3 JCY-1800 : EXT-LAN
JCY-1850 : JRC-LAN
VDR/S-VDR
Real Time Monitor
Client PC2 (*2)
192.168.0.248
LAN
VDR/S-VDR
Real Time Monitor
Client PC3 (*2)
VDR/S-VDR Real Time Monitor & Onboard LAN (Example) INTERCONNECTION DIAGRAM
VDR/S-VDR Real Time Monitor / Installation Manual
78
Chapter9 Appendix
STEP 1
Set by Maintenance software
(1)Open the Option PC（VDR Real Time Monitor）screen.
(2)Click the [Receive] button to receive the VDR/S-VDR configuration data.
(3)Click the [All Enable] button.
(4)Check that the following addresses in VDR WAN and Option PC.
・ VDR WAN=192.168.0.254
・ Option PC=192.168.0.251
VDR WAN
/Option PC
[All Enable]
button
(5) If the IP address is different, open the Network screen by the [Edit] button, and change IP
address.
When the [Default] button is clicked, default IP addresses are input.
[Default] button
(6) Click the [Set] button.
Setting by the Maintenance software is completion above.
After this, operate on Server PC of the VDR/S-VDR Real Time Monitor.
VDR Real Time Monitor / Installation Manual
79
Chapter9 Appendix
STEP 2 Set IP Address of Server PC
Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and set
the following IP address to the Server PC.
・IP Address
=192.168.0.251
・Subnet Mask
=255.255.255.0
It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor.
IP Address
/Subnet Mask
And then set the Server PC in accordance with the “6.2 Setup Items of PC”.
VDR/S-VDR Real Time Monitor / Installation Manual
80
Chapter9 Appendix
STEP 3 Set by the Setup software of Server PC
Install the VDR/S-VDR Real Time Monitor software in accordance with “9.4 Install Flow for
Server PC”, and set by the Setup software.
(1) System tab screen
・ Input “✓” when monitor or record in the Audio block is needed.
・ Input “✓” when connection or record in the FGB block is needed, and input the Radar
information.
・ Input “✓” to Terminal 1, 2 and 3 in Terminal block since there are 3 Client PCs.
・ Select the record folder when the VDR/S-VDR Real Time Monitor PC records.
・ Set record period in the Record block when recording.
Audio
FGB
Terminal
Folder
Record
VDR Real Time Monitor / Installation Manual
81
Chapter9 Appendix
(2)Ethernet tab screen
Check that the following IP address is set.
・LAN1(VDR Side)=192.168.0.251
・VDR IF(Router)
Connect=”✓”
WAN (FGB2 Side) = 192.168.111.100
LAN (Real Time Monitor Side) = 192.168.0.100
192.168.0.251
”✓”
(3) Click the [All Set] button, and setting of the Server PC is completion.
VDR/S-VDR Real Time Monitor / Installation Manual
82
Chapter9 Appendix
STEP 4
Set IP Address of Client PC
Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and set
the following IP address to the Client PC.
・IP Address
Client1=192.168.0.250
Client2=192.168.0.249
Client3=192.168.0.248
・Subnet Mask
=255.255.255.0
It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor.
IP Address
/Subnet Mask
And then set the Client PC in accordance with the “6.2 Setup Items of PC”.
VDR Real Time Monitor / Installation Manual
83
Chapter9 Appendix
STEP 5
Set by the Setup software of Client PC
Install the VDR/S-VDR Real Time Monitor software in accordance with “9.5 Install Flow for Client
PC”, and set by the Setup software.
(1)System tab screen
・ Input “✓” when monitor or record in the Audio block is needed.
・ Input “✓” when connection or record in the FGB block is needed, and input the Radar
information.
・ Select the record folder when the VDR/S-VDR Real Time Monitor PC records.
・ Set record period in the Record block when recording.
Audio
FGB
Folder
Record
VDR/S-VDR Real Time Monitor / Installation Manual
84
Chapter9 Appendix
(2)Ethernet tab screen
There is no setup in the Ethernet tab screen.
(3)Click the [All Set] button, and setting of the Client PC is completion.
Please set up other Client PC similarly.
VDR Real Time Monitor / Installation Manual
85
Chapter9 Appendix
STEP 6 Set firewall of the VDR IF（Router）
The firewall of VDR IF is canceled when shipped from a factory.
Please validate firewall by the following operation of telnet communication from the Server PC of
the VDR/S-VDR Real Time Monitor.
(1) To communicate by telnet from the Server PC of the VDR/S-VDR Real Time Monitor, input
as follows on the command prompt screen.
C:\>telnet 192.168.0.100
Enter
(2) To log in the VDR IF, input user name and password as follows
login: manager Enter
Password: friend Enter
(The input password is not displayed on screen.)
(3) To set script file of validated firewall, input the “set” command as follows.
Manager vdr_if> set Config＝18firon.cfg
Enter
(4) Close the command prompt screen, and to validate the script file, restart the VDR IF by
power switch.
(5) To check that the firewall became valid, input the “show” command as follows.
Since the VDR IF is restarted, open the command prompt screen again and check the
firewall after logging in the VDR IF.
If the "18firon.cfg" is displayed in the place of "Current configuration", firewall is valid.
Manager vdr_if> show config Enter
Boot configuration file: 18firon.cfg (exists)
Current configuration: 18firon.cfg
VDR/S-VDR Real Time Monitor / Installation Manual
86
Chapter9 Appendix
(6) Write the attached IP address seal as follows, and stick it on the VDR IF.
WAN：192.168.111.100
LAN：192.168.0.100
VDR IF setup is completion above.
Note
To set firewall invalid, select the "18firof.cfg" as script file at the (3)
and cancel firewall of the VDR IF.
VDR Real Time Monitor / Installation Manual
87
Chapter9 Appendix
9.2.4 Example4 In case of connecting with Client PC
Server and Client PC already are assigned different IP address (192.168.20.xxx) from default
value, and explains how to set when Server PC is connected to Client 1, Client 2 and Client3 PC.
On Board LAN System (Example)
JCY-1800/1850
VDR/S-VDR
EXT-LAN *3
HUB
192.168.0.254
192.168.20.XXX
RJ-45
LAN
*1 Ethernet cable
(Shield Twist-Pair cable)
Max. 30m
VDR/S-VDR
Real Time Monitor
Server PC (*2)
AC
192.168.20.XXX
VDR/S-VDR
Real Time Monitor
Client PC1 (*2)
192.168.20.XXX
LAN
LAN
VDR/S-VDR
Real Time Monitor
Client PC2 (*2)
192.168.20.XXX
LAN
NOTE
1. *1 Shielded LAN Cable(Cat5) : Dock Yard supply
2. *2 PC : Owner supply
3. *3 JCY-1800 : EXT-LAN
JCY-1850 : JRC-LAN
VDR/S-VDR
Real Time Monitor
Client PC3 (*2)
VDR/S-VDR Real Time Monitor & Onboard LAN (Example) INTERCONNECTION DIAGRAM
VDR/S-VDR Real Time Monitor / Installation Manual
88
Chapter9 Appendix
STEP 1
Set by Maintenance software
(1) Open the Option PC（VDR Real Time Monitor）screen.
(2) Click the [Receive] button to receive the VDR/S-VDR configuration data.
(3) Click the [All Enable] button.
(4) Check that the following addresses in VDR WAN and Option PC.
・ VDR WAN=192.168.0.254
・ Option PC=192.168.0.251
VDR WAN
/Option PC
[All Enable]
button
(5) If the IP address is different, open the Network screen by the [Edit] button, and change IP
address.
When the [Default] button is clicked, default IP addresses are input.
[Default] button
(6) Click the [Set] button.
Setting by the Maintenance software is completion above.
After this, operate on Server PC of the VDR/S-VDR Real Time Monitor.
VDR Real Time Monitor / Installation Manual
89
Chapter9 Appendix
STEP 2 Set IP Address of Server PC
Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and set
the following IP address to the Server PC.
If the IP address automatically is assigned by DHCP in the user LAN, cancel the DHCP. And
register an unused fix IP address in the user LAN and add above IP address.
(1) To add registration IP address, click the [Advanced] button.
[Advanced] button
VDR/S-VDR Real Time Monitor / Installation Manual
90
Chapter9 Appendix
(2) Click [Add] button, and add the following IP address and subnet mask.
・IP Address
=192.168.0.251
・Subnet Mask
=255.255.255.0
It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor.
And then set the Server PC in accordance with the “6.2 Setup Items of PC”.
VDR Real Time Monitor / Installation Manual
91
Chapter9 Appendix
STEP 3 Set by the Setup software of Server PC
Install the VDR/S-VDR Real Time Monitor software in accordance with “9.4 Install Flow for
Server PC”, and set by the Setup software.
(1) System tab screen
・ Input “✓” when monitor or record in the Audio block is needed.
・ Input “✓” when connection or record in the FGB block is needed, and input the Radar
information.
・ Input “✓” to Terminal 1, 2 and 3 in Terminal block since there are 3 Client PCs.
・ Select the record folder when the VDR/S-VDR Real Time Monitor PC records.
・ Set record period in the Record block when recording.
Audio
FGB
Terminal
Folder
Record
VDR/S-VDR Real Time Monitor / Installation Manual
92
Chapter9 Appendix
(2)Ethernet tab screen
Check that the following IP address is set.
・LAN1(VDR Side)=192.168.0.251
・VDR IF(Router)
Connect=None
192.168.0.251
None
(3) Click the [All Set] button, and setting of the Server PC is completion.
VDR Real Time Monitor / Installation Manual
93
Chapter9 Appendix
STEP 4
Set IP Address of Client PC
Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and set
the following IP address to the Client PC.
If the IP address automatically is assigned by DHCP in the user LAN, cancel the DHCP. And
register an unused fix IP address in the user LAN and add above IP address.
(1) To add registration IP address, click the [Advanced] button.
[Advanced] button
VDR/S-VDR Real Time Monitor / Installation Manual
94
Chapter9 Appendix
(2) Click [Add] button, and add the following IP address and subnet mask.
・IP Address
=192.168.0.251
・Subnet Mask
=255.255.255.0
It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor.
And then set the Server PC in accordance with the “6.2 Setup Items of PC”.
VDR Real Time Monitor / Installation Manual
95
Chapter9 Appendix
STEP 5
Set by the Setup software of Client PC
Install the VDR/S-VDR Real Time Monitor software in accordance with “9.5 Install Flow for Client
PC”, and set by the Setup software.
(1)System tab screen
・ Input “✓” when monitor or record in the Audio block is needed.
・ Input “✓” when connection or record in the FGB block is needed, and input the Radar
information.
・ Select the record folder when the VDR/S-VDR Real Time Monitor PC records.
・ Set record period in the Record block when recording.
Audio
FGB
Folder
Record
VDR/S-VDR Real Time Monitor / Installation Manual
96
Chapter9 Appendix
(2) Ethernet tab screen
There is no setup in the Ethernet tab screen.
(3) Click the [All Set] button, and setting of the Client PC is completion.
Please set up other Client PC similarly.
VDR Real Time Monitor / Installation Manual
97
Chapter9 Appendix
9.2.5 Example5 In case of connecting with Client PC and Radar IF
Server and Client PC already is assigned different IP address (192.168.20.xxx) from default
value, and explains how to set when Server PC is connected to Client 1, Client 2, Client3 PC and
Radar IF.
Note
Radar IF (NWP-46)
In the VDR/S-VDR equipment main Radar image is captured
and recorded, and it is possible to capture or record images of
sub Radar and ECDIS by the Radar IF in the VDR/S-VDR Real
Time Monitor.
VDR/S-VDR Real Time Monitor / Installation Manual
98
Chapter9 Appendix
STEP 1
Set by Maintenance software
(1) Open the Option PC（VDR Real Time Monitor）screen.
(2) Click the [Receive] button to receive the VDR/S-VDR configuration data.
(3) Click the [All Enable] button.
(4) Check that the following addresses in VDR WAN and Option PC.
・ VDR WAN=192.168.0.254
・ Option PC=192.168.0.251
VDR WAN
/Option PC
[All Enable]
button
(5) If the IP address is different, open the Network screen by the [Edit] button, and change IP
address.
When the [Default] button is clicked, default IP addresses are input.
[Default] button
(6) Click the [Set] button.
Setting by the Maintenance software is completion above.
After this, operate on Server PC of the VDR/S-VDR Real Time Monitor.
VDR Real Time Monitor / Installation Manual
99
Chapter9 Appendix
STEP 2
Set IP Address of Server PC
Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and add
registration of IP address and subnet mask to the Server PC.
If the IP address automatically is assigned by DHCP in the user LAN, cancel the DHCP. And
register an unused fix IP address in the user LAN and add above IP address.
(1) To add registration IP address, click the [Advanced] button.
[Advanced] button
VDR/S-VDR Real Time Monitor / Installation Manual
100
Chapter9 Appendix
(2) Click [Add] button, and add the following IP address and subnet mask.
・IP Address
=192.168.0.251
・Subnet Mask
=255.255.255.0
It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor.
And then set the Server PC in accordance with the “6.2 Setup Items of PC”.
VDR Real Time Monitor / Installation Manual
101
Chapter9 Appendix
STEP 3 Set by the Setup software of Server PC
Install the VDR/S-VDR Real Time Monitor software in accordance with “9.4 Install Flow for
Server PC”, and set by the Setup software.
(1) System tab screen
・ Input “✓” when monitor or record in the Audio block is needed.
・ Input “✓” when connection or record in the FGB block is needed, and input the Radar
information.
・ Input “✓” to Terminal 1, 2 and 3 in Terminal block since there are 3 Client PCs.
・ Select the record folder when the VDR/S-VDR Real Time Monitor PC records.
・ Set record period in the Record block when recording.
Audio
FGB
Terminal
Folder
Record
VDR/S-VDR Real Time Monitor / Installation Manual
102
Chapter9 Appendix
(2) Ethernet tab screen
Check that the following IP address is set.
・LAN1(VDR Side)=192.168.0.251
・VDR IF(Router)
Connect=”✓”
WAN (FGB2 Side) = 192.168.111.100
LAN (Real Time Monitor Side) = 192.168.0.100
192.168.0.251
”✓”
(3) Click the [All Set] button, and setting of the Server PC is completion.
VDR Real Time Monitor / Installation Manual
103
Chapter9 Appendix
STEP 4
Set IP Address of Client PC
Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and
add registration of IP address and subnet mask to Client PC.
If the IP address automatically is assigned by DHCP in the user LAN, cancel the DHCP. And
register an unused fix IP address in the user LAN and add above IP address.
(1) To add registration IP address, click the [Advanced] button.
[Advanced] button
And then set the Client PC in accordance with the “6.2 Setup Items of PC”.
VDR/S-VDR Real Time Monitor / Installation Manual
104
Chapter9 Appendix
(2) Click [Add] button, and add the following IP address and subnet mask.
・IP Address
Client1=192.168.0.250
Client2=192.168.0.249
Client3=192.168.0.248
・Subnet Mask
=255.255.255.0
It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor.
VDR Real Time Monitor / Installation Manual
105
Chapter9 Appendix
STEP 5
Set by the Setup software of Client PC
Install the VDR/S-VDR Real Time Monitor software in accordance with “9.5 Install Flow for Client
PC”, and set by the Setup software.
(1)System tab screen
・ Input “✓” when monitor or record in the Audio block is needed.
・ Input “✓” when connection or record in the FGB block is needed, and input the Radar
information.
・ Select the record folder when the VDR/S-VDR Real Time Monitor PC records.
・ Set record period in the Record block when recording.
Audio
FGB
Folder
Record
VDR/S-VDR Real Time Monitor / Installation Manual
106
Chapter9 Appendix
(2) Ethernet tab screen
There is no setup in the Ethernet tab screen.
(3) Click the [All Set] button, and setting of the Client PC is completion.
Please set up other Client PC similarly.
VDR Real Time Monitor / Installation Manual
107
Chapter9 Appendix
STEP 6 Set firewall of the VDR IF（Router）
The firewall of VDR IF is canceled when shipped from a factory.
Please validate firewall by the following operation of telnet communication from the Server PC of
the VDR/S-VDR Real Time Monitor.
(1) To communicate by telnet from the Server PC of the VDR/S-VDR Real Time Monitor, input
as follows on the command prompt screen.
C:\>telnet 192.168.0.100
Enter
(2) To log in the VDR IF, input user name and password as follows
login: manager Enter
Password: friend Enter
(The input password is not displayed on screen.)
(3) To set script file of validated firewall, input the “set” command as follows.
Manager> set Config＝18firon.cfg
Enter
(4) Close the command prompt screen, and to validate the script file, restart the VDR IF by
power switch.
(5) To check that the firewall became valid, input the “show” command as follows.
Since the VDR IF is restarted, open the command prompt screen again and check the
firewall after logging in the VDR IF.
If the "18firon.cfg" is displayed in the place of "Current configuration", firewall is valid.
Manager vdr_if> show config Enter
Boot configuration file: 18firon.cfg (exists)
Current configuration: 18firon.cfg
VDR/S-VDR Real Time Monitor / Installation Manual
108
Chapter9 Appendix
(6) Write the attached IP address seal as follows, and stick it on the VDR IF.
WAN：192.168.111.100
LAN：192.168.0.100
VDR IF setup is completion above.
Note
To set firewall invalid, select the "18firof.cfg" as script file at the (3)
and cancel firewall of the VDR IF.
VDR Real Time Monitor / Installation Manual
109
Chapter9 Appendix
9.2.6 Example6 In case of connecting with Client PC
Server and Client PC already are assigned different IP address (192.168.0.xxx) from default
value, and explains how to set when Server PC is connected to Client 1, Client 2 and Client3 PC.
On Board LAN System (Example)
JCY-1800/1850
VDR/S-VDR
EXT-LAN *3
HUB
192.168.0.254
192.168.0.11
RJ-45
LAN
*1 Ethernet cable
(Shield Twist-Pair cable)
Max. 30m
192.168.0.12
VDR/S-VDR
Real Time Monitor
Server PC (*2)
192.168.0.10
VDR/S-VDR
Real Time Monitor
Client PC1 (*2)
LAN
LAN
VDR/S-VDR
Real Time Monitor
Client PC2 (*2)
AC
192.168.0.13
LAN
NOTE
1. *1 Shielded LAN Cable(Cat5) : Dock Yard supply
2. *2 PC : Owner supply
3. *3 JCY-1800 : EXT-LAN
JCY-1850 : JRC-LAN
VDR/S-VDR
Real Time Monitor
Client PC3 (*2)
VDR/S-VDR Real Time Monitor & Onboard LAN (Example) INTERCONNECTION DIAGRAM
VDR/S-VDR Real Time Monitor / Installation Manual
110
Chapter9 Appendix
STEP 1
Set by Maintenance software
(1) Open the Option PC（VDR Real Time Monitor）screen.
(2) Click the [Receive] button to receive the VDR/S-VDR configuration data.
(3) Click the [All Enable] button.
(4) Check that the following addresses in VDR WAN and Option PC.
・ VDR WAN=192.168.0.254
・ Option PC=192.168.0.10
VDR WAN
/Option PC
[All Enable]
button
(5) If the IP address is different, open the Network screen by the [Edit] button, and change IP
address.
When the [Default] button is clicked, default IP addresses are input.
[Default] button
(6) Click the [Set] button.
Setting by the Maintenance software is completion above.
After this, operate on Server PC of the VDR/S-VDR Real Time Monitor.
VDR Real Time Monitor / Installation Manual
111
Chapter9 Appendix
STEP 2 Set IP Address of Server PC
Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and check
that the following IP address is registered into the Server PC.
・IP Address
=192.168.0.10
・Subnet Mask
=255.255.255.0
It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor.
IP Address
/Subnet Mask
And then set the Server PC in accordance with the “6.2 Setup Items of PC”.
VDR/S-VDR Real Time Monitor / Installation Manual
112
Chapter9 Appendix
STEP 3 Set by the Setup software of Server PC
Install the VDR/S-VDR Real Time Monitor software in accordance with “9.4 Install Flow for
Server PC”, and set by the Setup software.
(1) System tab screen
・ Input “✓” when monitor or record in the Audio block is needed.
・ Input “✓” when connection or record in the FGB block is needed, and input the Radar
information.
・ Input “✓” to Terminal 1, 2 and 3 in Terminal block since there are 3 Client PCs.
・ Select the record folder when the VDR/S-VDR Real Time Monitor PC records.
・ Set record period in the Record block when recording.
Audio
FGB
Terminal
Folder
Record
VDR Real Time Monitor / Installation Manual
113
Chapter9 Appendix
(2)Ethernet tab screen
Check that the following IP address is set.
・LAN1(VDR Side)=192.168.0.251
・VDR IF(Router)
Connect=None
192.168.0.251
None
(3)Set the following IP address in the Terminal block.
・Terminal1=192.168.0.11
・Terminal2=192.168.0.12
・Terminal3=192.168.0.13
(4)Click the [All Set] button, and setting of the Server PC is completion.
VDR/S-VDR Real Time Monitor / Installation Manual
114
Chapter9 Appendix
STEP 4 Set IP Address of Client PC
Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and check
that the following IP address is registered into the Client PC.
・IP Address
Client1
Client2
Client3
=192.168.0.11
=192.168.0.12
=192.168.0.13
・Subnet Mask
=255.255.255.0
It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor.
IP Address
/Subnet Mask
And then set the Client PC in accordance with the “6.2 Setup Items of PC”.
VDR Real Time Monitor / Installation Manual
115
Chapter9 Appendix
STEP 5
Set by the Setup software of Client PC
Install the VDR/S-VDR Real Time Monitor software in accordance with “9.5 Install Flow for Client
PC”, and set by the Setup software.
(1)System tab screen
・ Input “✓” when monitor or record in the Audio block is needed.
・ Input “✓” when connection or record in the FGB block is needed, and input the Radar
information.
・ Select the record folder when the VDR/S-VDR Real Time Monitor PC records.
・ Set record period in the Record block when recording.
Audio
FGB
Folder
Record
VDR/S-VDR Real Time Monitor / Installation Manual
116
Chapter9 Appendix
(2) Ethernet tab screen
There is no setup in the Ethernet tab screen.
(3) Click the [All Set] button, and setting of the Client PC is completion.
Please set up other Client PC similarly.
VDR Real Time Monitor / Installation Manual
117
Chapter9 Appendix
STEP 6
Change setup of VDR IF (Router)
Change the described IP filter in the script file of VDR/S-VDR.
The script file to change is "18firon.cfg."
There is the script file in the VDR/S-VDR Real Time Monitor install CD-ROM.
Script file
VDR/S-VDR Real Time Monitor / Installation Manual
118
Chapter9 Appendix
(1)Open the 18firon.cfg file by text editor (Example: Notepad), and change it.
Change part is IP Address which is adding shading, and please input the IP address of Server
PC.
In this example, since it is “Server PC=192.168.0.10”, it is set to source=”192.168.0.10.”
# Command Handler configuration
# System configuration
set system name="VDR_IF"
# User configuration
set user=manager pass=3af00c6cad11f7ab5db4467b66ce503eff priv=manager lo=yes
set user=manager telnet=yes desc="Manager Account"
# IP configuration
Change to192.168.0.10
enable ip
add ip interface=vlan1 ip=192.168.0.100 mask=255.255.255.0
add ip interface=eth0 ip=192.168.111.100 mask=255.255.255.0
# INT configuration
add ip filter=0 type=traffic source=192.168.0.251 ac=include smask=255.255.255.255 destination=192.168.111.152
dmask=255.255.255.255 icmptype=8 prot=icmp
add ip filter=0 type=traffic source=192.168.0.251 ac=include smask=255.255.255.255 destination=192.168.111.152
dmask=255.255.255.255 dport=80 prot=tcp
add ip filter=0 type=traffic source=192.168.0.251 ac=include smask=255.255.255.255 destination=192.168.0.100
dmask=255.255.255.255 dport=23 prot=tcp
set ip int=vlan1 filter=0
VDR Real Time Monitor / Installation Manual
119
Chapter9 Appendix
(2) In order to send the Script file to the VDR IF, connect the VDR IF setting cable as follows.
(3)Start the Hyper Terminal software, and set as follows.
Please refer to “9.3 Hyper Terminal Setup” for more detail.
Item
Value
Bits per second
Data bits
9,600bps
8
Parity
None
Stop bits
1
Flow control
Emulation
Backspace key sends
Hardware
VT100J
Delete
Input Translation
Shift－JIS(S)
(4)Input the following user name and password, and log into the VDR IF.
login: manager Enter
Password: friend Enter
(The input password is not displayed on screen.)
VDR/S-VDR Real Time Monitor / Installation Manual
120
Chapter9 Appendix
(5)Delete the current script file by the “delete” command as follows.
Manager vdr_if> delete file=18firon.cfg
Enter
(6)To send the changed script file, input the “load” command as follows.
Manager vdr_if> load method=zmodem asyn=0 destination=flash
Router ready to begin ZMODEM file transfers . . .
Enter
(7) Select menu in order of "Transfer" and "Send File", and the following screen is indicated.
Click the [Browse] button, and select the changed “18firon.cfg” file, and click the [Send] button
to transfer.
Manager vdr_if> load method=zmodem asyn=0 destination=flash
Router ready to begin ZMODEM file transfers . . .
･B000000023be50
Info (1048293): ZMODEM, session over.
Enter
(8) To validate the”18firon.cfg” file, input the “set” command as follows.
Manager vdr_if> set config=18firon.cfg
Enter
VDR Real Time Monitor / Installation Manual
121
Chapter9 Appendix
(9) Close the Hyper Terminal software, and restart the VDR IF by power switch.
(10) To check that the firewall became valid, input the “show” command as follows.
Since the VDR IF is restarted, open the command prompt screen again and check the firewall
after logging in the VDR IF.
If the "18firon.cfg" is displayed in the place of "Current configuration", firewall is valid.
Manager vdr_if> show config Enter
Boot configuration file: 18firon.cfg (exists)
Current configuration: 18firon.cfg
(11) Write the attached IP address seal as follows, and stick it on the VDR IF.
WAN：192.168.111.100
LAN：192.168.0.100
VDR IF setup is completion above.
Note
To set firewall invalid, select the "18firof.cfg" as script file at the (8)
and cancel firewall of the VDR IF.
VDR/S-VDR Real Time Monitor / Installation Manual
122
Chapter9 Appendix
9.2.7 Example7 In case of connecting with Client PC and Radar IF
Server and Client PC already is assigned different IP address (192.168.0.xxx) from default value,
and explains how to set when Server PC is connected to Client 1, Client 2 , Client3 PC and
Radar IF.
Note
Radar IF (NWP-46)
In the VDR/S-VDR equipment main Radar image is captured
and recorded, and it is possible to capture or record images of
sub Radar, ECDIS and Conning by the Radar IF in the
VDR/S-VDR Real Time Monitor.
On Board LAN System (Example)
LAN
NWP-46
Radar IF
192.168.111.152
WAN
192.168.111.100
JCY-1800/1850
VDR/S-VDR
VDR IF(Router)
EXT-LAN *3
LAN
RJ-45
192.168.0.254
192.168.0.100
HUB
192.168.0.11
*1 Ethernet cable
(Shield Twist-Pair cable)
Max. 30m
LAN
VDR/S-VDR
Real Time Monitor
Server PC (*2)
192.168.0.10
VDR/S-VDR
Real Time Monitor
Client PC1 (*2)
LAN
192.168.0.12
AC
LAN
NOTE
1. *1 Shielded LAN Cable(Cat5) : Dock Yard supply
2. *2 PC : Owner supply
3. *3 JCY-1800 : EXT-LAN
JCY-1850 : JRC-LAN
VDR/S-VDR
Real Time Monitor
Client PC2 (*2)
192.168.0.13
LAN
VDR/S-VDR
Real Time Monitor
Client PC3 (*2)
VDR/S-VDR Real Time Monitor & Onboard LAN (Example) INTERCONNECTION DIAGRAM
VDR Real Time Monitor / Installation Manual
123
Chapter9 Appendix
STEP 1
Set by Maintenance software
(1) Open the Option PC（VDR Real Time Monitor）screen.
(2) Click the [Receive] button to receive the VDR/S-VDR configuration data.
(3) Click the [All Enable] button.
(4) Check that the following addresses in VDR WAN and Option PC.
・ VDR WAN=192.168.0.254
・ Option PC=192.168.0.10
VDR WAN
/Option PC
[All Enable]
button
(5) If the IP address is different, open the Network screen by the [Edit] button, and change IP
address.
When the [Default] button is clicked, default IP addresses are input.
[Default] button
(6) Click the [Set] button.
Setting by the Maintenance software is completion above.
After this, operate on Server PC of the VDR/S-VDR Real Time Monitor.
VDR/S-VDR Real Time Monitor / Installation Manual
124
Chapter9 Appendix
STEP 2 Set IP Address of Server PC
Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and check
that the following IP address is registered into the Server PC.
・IP Address
=192.168.0.10
・Subnet Mask
=255.255.255.0
It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor.
IP Address
/Subnet Mask
And then set the Server PC in accordance with the “6.2 Setup Items of PC”.
VDR Real Time Monitor / Installation Manual
125
Chapter9 Appendix
STEP 3 Set by the Setup software of Server PC
Install the VDR/S-VDR Real Time Monitor software in accordance with “9.4 Install Flow for
Server PC”, and set by the Setup software.
(1) System tab screen
・ Input “✓” when monitor or record in the Audio block is needed.
・ Input “✓” when connection or record in the FGB block is needed, and input the Radar
information.
・ Input “✓” to Terminal 1, 2 and 3 in Terminal block since there are 3 Client PCs.
・ Select the record folder when the VDR/S-VDR Real Time Monitor PC records.
・ Set record period in the Record block when recording.
Audio
FGB
Terminal
Folder
Record
VDR/S-VDR Real Time Monitor / Installation Manual
126
Chapter9 Appendix
(2)Ethernet tab screen
Check that the following IP address is set.
・LAN1(VDR Side)=192.168.0.251
・VDR IF(Router)
Connect=None
192.168.0.251
None
(3)Set the following IP address in the Terminal block.
・Terminal1=192.168.0.11
・Terminal2=192.168.0.12
・Terminal3=192.168.0.13
(4)Click the [All Set] button, and setting of the Server PC is completion.
VDR Real Time Monitor / Installation Manual
127
Chapter9 Appendix
STEP 4 Set IP Address of Client PC
Open the properties screen of Internet protocol (TC/IP) in the Windows control panel, and check
that the following IP address is registered into the Client PC.
・IP Address
Client1
Client2
Client3
=192.168.0.11
=192.168.0.12
=192.168.0.13
・Subnet Mask
=255.255.255.0
It is not necessary to set Default gateway for the VDR/S-VDR Real Time Monitor.
IP Address
/Subnet Mask
And then set the Client PC in accordance with the “6.2 Setup Items of PC”.
VDR/S-VDR Real Time Monitor / Installation Manual
128
Chapter9 Appendix
STEP 5
Set by the Setup software of Client PC
Install the VDR/S-VDR Real Time Monitor software in accordance with “9.5 Install Flow for Client
PC”, and set by the Setup software.
(1)System tab screen
・ Input a check when monitor or record in the Audio block is needed.
・ Input a check when connection or record in the FGB block is needed, and input the Radar
information.
・ Select the record folder when the VDR/S-VDR Real Time Monitor PC records.
・ Set record period in the Record block when recording.
Audio
FGB
Folder
Record
VDR Real Time Monitor / Installation Manual
129
Chapter9 Appendix
(2) Ethernet tab screen
There is no setup in the Ethernet tab screen.
(3) Click the [All Set] button, and setting of the Client PC is completion.
Please set up other Client PC similarly.
VDR/S-VDR Real Time Monitor / Installation Manual
130
Chapter9 Appendix
STEP 6
Change setup of VDR IF (Router)
Change the described IP filter in the script file of VDR/S-VDR.
The script file to change is "18firon.cfg."
There is the script file in the VDR/S-VDR Real Time Monitor install CD-ROM.
Script file
VDR Real Time Monitor / Installation Manual
131
Chapter9 Appendix
(1)Open the 18firon.cfg file by text editor (Example: Notepad), and change it.
Change part is IP Address which is adding shading, and please input the IP address of Server
PC.
In this example, since it is “Server PC=192.168.0.10”, it is set to source=”192.168.0.10.”
# Command Handler configuration
# System configuration
set system name="VDR_IF"
# User configuration
set user=manager pass=3af00c6cad11f7ab5db4467b66ce503eff priv=manager lo=yes
set user=manager telnet=yes desc="Manager Account"
# IP configuration
Change to192.168.0.10
enable ip
add ip interface=vlan1 ip=192.168.0.100 mask=255.255.255.0
add ip interface=eth0 ip=192.168.111.100 mask=255.255.255.0
# INT configuration
add ip filter=0 type=traffic source=192.168.0.251 ac=include smask=255.255.255.255 destination=192.168.111.152
dmask=255.255.255.255 icmptype=8 prot=icmp
add ip filter=0 type=traffic source=192.168.0.251 ac=include smask=255.255.255.255 destination=192.168.111.152
dmask=255.255.255.255 dport=80 prot=tcp
add ip filter=0 type=traffic source=192.168.0.251 ac=include smask=255.255.255.255 destination=192.168.0.100
dmask=255.255.255.255 dport=23 prot=tcp
set ip int=vlan1 filter=0
VDR/S-VDR Real Time Monitor / Installation Manual
132
Chapter9 Appendix
(2) In order to send the Script file to the VDR IF, connect the VDR IF setting cable as follows.
(3)Start the Hyper Terminal software, and set as follows.
Please refer to “9.3 Hyper Terminal Setup” for more detail.
Item
Value
Bits per second
Data bits
9,600bps
8
Parity
Stop bits
None
1
Flow control
Emulation
Backspace key sends
Input Translation
Hardware
VT100J
Delete
Shift－JIS(S)
(4)Input the following user name and password, and log into the VDR IF.
login: manager Enter
Password: friend Enter
(No displayed)
VDR Real Time Monitor / Installation Manual
133
Chapter9 Appendix
(5)Delete the current script file by the “delete” command as follows.
Manager vdr_if> delete file=18firon.cfg
Enter
(6)To send the changed script file, input the “load” command as follows.
Manager vdr_if> load method=zmodem asyn=0 destination=flash
Router ready to begin ZMODEM file transfers . . .
Enter
(7) Select menu in order of "Transfer" and "Send File", and the following screen is indicated.
Click the [Browse] button, and select the changed “18firon.cfg” file, and click the [Send] button
to transfer.
Manager vdr_if> load method=zmodem asyn=0 destination=flash
Router ready to begin ZMODEM file transfers . . .
･B000000023be50
Info (1048293): ZMODEM, session over.
(8) To validate the”18firon.cfg” file, input the “set” command as follows.
Manager vdr_if> set config=18firon.cfg
Enter
VDR/S-VDR Real Time Monitor / Installation Manual
134
Enter
Chapter9 Appendix
(9) Close the Hyper Terminal software, and restart the VDR IF by power switch.
(10) To check that the firewall became valid, input the “show” command as follows.
Since the VDR IF is restarted, open the command prompt screen again and check the firewall
after logging in the VDR IF.
If the "18firon.cfg" is displayed in the place of "Current configuration", firewall is valid.
Manager vdr_if> show config Enter
Boot configuration file: 18firon.cfg (exists)
Current configuration: 18firon.cfg
(11) Write the attached IP address seal as follows, and stick it on the VDR IF.
WAN：192.168.111.100
LAN：192.168.0.100
VDR IF setup is completion above.
Note
To set firewall invalid, select the "18firof.cfg" as script file at the (8)
and cancel firewall of the VDR IF.
VDR Real Time Monitor / Installation Manual
135
Chapter9 Appendix
STEP 6
Change Radar IF setup
It is necessary to change destination IP address of UDP output from the Radar IF since the
Server PC IP address is changed.
To change the IP address, download the IP.txt by the Internet Explorer of the Server PC, and
change it.
In this example, destination IP address is changed from 192.168.000.251 into 192.168.000.010.
IP.txt
IP=192.168.111.152
SUB=255.255.255.000
MAC=xx:xx:xx:xx:xx:xx
GW=192.168.111.100
UDP=192.168.000.251 Å 192.168.000.010
UPORT=6001
UDP_Delay=2000
UDP_Wait=2000
(1) To communicate Server PC to the Radar IF, set the route table by the route command on the
command prompt screen.
C:\>route add 192.168.111.152 mask 255.255.255.255 192.168.0.100 Enter
VDR/S-VDR Real Time Monitor / Installation Manual
136
Chapter9 Appendix
(1) Input “192.168.111.152” in the Address, and the following screen is displayed.
Address
IP.txt
VDR Real Time Monitor / Installation Manual
137
Chapter9 Appendix
(2) Click the IP.txt menu, and the content of the IP.txt is displayed.
Please select “Save As” in the File menu, and save the IP.txt on the desktop.
(3) Open the saved Ip.txt file by the Notepad, and set the Server PC IP address as the destination.
In this example, destination IP address is 192.168.000.010.
And delete "IP.txt OK" of the unnecessary 1st line and save the file.
IP=192.168.111.152
SUB=255.255.255.000
MAC=xx:xx:xx:xx:xx:xx
GW=192.168.111.100
UDP=192.168.000.010
UPORT=6001
UDP_Delay=2000
UDP_Wait=2000
IP.txt OK
Å 削除
IP=192.168.111.152
SUB=255.255.255.000
MAC=xx:xx:xx:xx:xx:xx
GW=192.168.111.100
UDP=192.168.000.251 Å 192.168.000.10
UPORT=6001
UDP_Delay=2000
UDP_Wait=2000
Before
After
VDR/S-VDR Real Time Monitor / Installation Manual
138
Chapter9 Appendix
(4) To send the IP.txt file, click the IP.txt upload menu.
IP.txt upload
VDR Real Time Monitor / Installation Manual
139
Chapter9 Appendix
(5) Click the [Browse] button, and select the changed IP.txt file.
To send it, click the [Upload] button.
If transfer is finished, “Ip.txt write OK”message is displayed.
VDR/S-VDR Real Time Monitor / Installation Manual
140
Chapter9 Appendix
(6) To restart the FGB, click the Reset menu.
Reset
Radar IF setup is completion above.
VDR Real Time Monitor / Installation Manual
141
Chapter9 Appendix
9.3 Hyper Terminal Setup
9.3.1 Starting
(1) Select from a [start] button in order of "All Programs" => "Accessories" =>
"Communications" => "Hyper Terminal."
(2) Enter a name for the connection, and click the [OK] button.
Here, "VDR_IF" is inputted as an example.
(3) Select a COM port which connects with the VDR IF, and click the [OK] button.
(4) Set the “Bits per second” as 9600, and click the [OK] button.
(Please leave to a default value except the "bits per second.")
VDR/S-VDR Real Time Monitor / Installation Manual
142
Chapter9 Appendix
(5) The Hyper Terminal screen is indicated.
(6) Select the Properties in the File menu, and select the Setting tab.
Set the following items.
・Backspace key sends ⇒ Delete
・Emulation
⇒ VT100J
(7) Click the [Input Translation] button and click the [OK] button after the “Shift-JIS” selection.
VDR Real Time Monitor / Installation Manual
143
Chapter9 Appendix
9.3.2 End
(1) If still logged in to the VDR IF, please input the “logoff “ command in order to log off.
Manager vdr_if > logoff
(2) Click the Exit in the File menu bar.
(3) When the confirmation screen is indicated, click the [Yes] button.
(4) If you save the connection information, click the [Yes] button.
If the information is not necessary, click the [No] button.
The Hyper Terminal is ended.
VDR/S-VDR Real Time Monitor / Installation Manual
144
Specify a CF card drive.
Specify a playback folder.
《 Playback only 》
9.4 Installation Flow for Server PC
《 Live + Playback 》
Close
All Set
145
Check contents of engine, thruster, rudder, propeller, Keel – Trans and sensor sentences.
Specify Terminal1-3 IP addresses.
Configuration
Ethernet
System
Setting Tab
VDR Real Time Monitor / Installation Manual
Set record period and overwrite.
Specify a CF card drive.
Specify IP address of shipboard LAN side.
Specify a playback folder.
Specify a folder for playback and record.
Set existence of Radar monitor and record.
Set existence of Radar monitor.
Set existence of Terminal1-3 connections.
Set existence of audio monitor and record.
《 Live + Playback + Record 》
Set existence of audio monitor.
Import VDR configuration (SysInfo.dat) from a CF card built in VDR/S-VDR.
Log in with Serviceman authority.（Password “jrcvdr”）
Start the SETUP software.
Start the VDR Launcher.
Install the VDR/S-VDR Real Time Monitor by CD-ROM.
Set real time outputs in the Option PC screen of the Maintenance software.
《 Live only 》
Chapter9 Appendix
《 Live + Playback 》
《 Live + Playback + Record 》
Set record period and overwrite.
Specify a CF card drive.
Specify a folder for playback and record.
146
Close
All Set
Check contents of engine, thruster, rudder, propeller, Keel – Trans and sensor sentences.
Specify a playback folder.
and record.
Set existence of Radar Interface connection
Import VDR configuration from a CF card built in VDR/S-VDR.
Log in with Serviceman authority.（Password “jrcvdr”）
Start the SETUP software.
Start the VDR Launcher.
Install the VDR/S-VDR Real Time Monitor by CD-ROM.
Set existence of Radar Interface connection.
《 Live only 》
VDR Real Time Monitor / Installation Manual
case of playback only.
There is not client mode in
《 Playback only 》
9.5 Installation Follow for Client PC
Chapter9 Appendix
Configuration
System
Setting Tab
For further information,contact:
Not use the asbestos
URL
http://www.jrc.co.jp
Marine Service Department
Telephone : +81-3-3492-1305
+81-3-3779-1420
Facsimile :
[email protected]
e-mail :
AMSTERDAM Branch
Telephone : +31-20-658-0750
+31-20-658-0755
Facsimile :
[email protected]
e-mail :
SEATTLE Branch