Amcrest IP2M-848E User Manual

Amcrest IP2M-848E
2MP 4x Zoom PoE PTZ Camera
User Manual
Version 2.0.0
Revised June 28nd, 2016
1
Welcome ........................................................................................................................................................................6
Important Security Warning ..........................................................................................................................................6
Important Safeguards and Warnings .............................................................................................................................7
1 Features and Specifications ........................................................................................................................................8
1.1 Overview ..............................................................................................................................................................8
1.2 Features ...............................................................................................................................................................8
2 Device Overview .........................................................................................................................................................9
3 Connection & Installation .........................................................................................................................................10
3.1 Connection Guide ..............................................................................................................................................10
3.2 Installation Guide ...............................................................................................................................................10
4 Camera Access Setup ................................................................................................................................................11
4.1 Default Username and Password ......................................................................................................................11
4.2 Camera setup methods......................................................................................................................................12
4.2.1 Setting up your camera for the first time ...................................................................................................12
4.2.2 Accessing your camera using multiple mobile devices ...............................................................................12
4.2.3 Configuring advanced settings on your camera .........................................................................................12
4.2.4 Using Amcrest Cloud for remote viewing, storage, and playback ..............................................................12
4.2.5 Using plug-and-play for remote web access ...............................................................................................12
4.3 Amcrest View App Setup ...................................................................................................................................13
4.3.1 P2P Setup ....................................................................................................................................................13
4.3.2 App walkthrough ........................................................................................................................................16
4.3.3 Motion detection setup ..............................................................................................................................16
4.3.4 Push notifications setup .............................................................................................................................18
4.3.5 Email alerts setup .......................................................................................................................................21
4.4 Desktop access setup .........................................................................................................................................23
4.4.1 Amcrest IP Config Software method ..........................................................................................................23
4.4.2 Installing the Amcrest browser plugin ........................................................................................................27
2
4.4.3 Logging in ....................................................................................................................................................28
4.5 Amcrest Cloud Setup .........................................................................................................................................29
4.6 Web Access Setup (AmcrestView.com) .............................................................................................................30
4.6.1 Installing the AmcrestView.com browser plugin .................................................................................30
4.6.2 User method ............................................................................................................................................33
4.7 Remote Web Access Setup ................................................................................................................................39
4.7.1 UPnP/DDNS Remote Web Access Setup .....................................................................................................39
4.7.2 Port Forwarding Remote Web Access Setup ..............................................................................................40
4.8 NVR Access ........................................................................................................................................................41
5 Operation and Interface ...........................................................................................................................................42
5.1 Live .....................................................................................................................................................................42
5.2 PTZ .....................................................................................................................................................................44
5.3 Playback .............................................................................................................................................................45
5.4 Setup ..................................................................................................................................................................47
5.4.1 Camera ........................................................................................................................................................48
5.4.1.1 Configuration .......................................................................................................................................48
5.4.1.2 Video ....................................................................................................................................................51
5.4.1.3 Audio ....................................................................................................................................................54
5.4.2 Network ......................................................................................................................................................55
5.4.2.1 TCP/IP ..................................................................................................................................................55
5.4.2.2 Connection ...........................................................................................................................................57
5.4.2.3 PPPoE ...................................................................................................................................................58
5.4.2.4 DDNS ....................................................................................................................................................59
5.4.2.5 IP Filter .................................................................................................................................................60
5.4.2.6 SMTP (Email) ........................................................................................................................................61
5.4.2.7 UPnP ....................................................................................................................................................62
5.4.2.8 SNMP ...................................................................................................................................................63
3
5.4.2.9 Bonjour ................................................................................................................................................63
5.4.2.10 Multicast ............................................................................................................................................64
5.4.2.11 802.1x ................................................................................................................................................64
5.4.2.12 QoS.....................................................................................................................................................65
5.4.3 Event ...........................................................................................................................................................66
5.4.3.1 Video Detection ...................................................................................................................................66
5.4.3.2 Audio Detection ...................................................................................................................................69
5.4.3.3 Alarm ...................................................................................................................................................70
5.4.3.4 Abnormality .........................................................................................................................................72
5.4.4 Storage ........................................................................................................................................................75
5.4.4.1 Schedule ..............................................................................................................................................75
5.4.4.2 Destination ..........................................................................................................................................78
5.4.4.3 Record Control .....................................................................................................................................80
5.4.5 System ........................................................................................................................................................81
5.4.5.1 General ................................................................................................................................................81
5.4.5.2 Manage Users ......................................................................................................................................83
5.4.5.3 Restore Factory Settings ......................................................................................................................84
5.4.5.4 Import/Export ......................................................................................................................................84
5.4.5.5 Auto Maintain ......................................................................................................................................85
5.4.5.6 Upgrade ...............................................................................................................................................85
5.4.6 Information .................................................................................................................................................86
5.4.6.1 Version .................................................................................................................................................86
5.4.6.2 Log .......................................................................................................................................................86
5.4.6.3 Online Users .........................................................................................................................................87
5.5 Alarm .................................................................................................................................................................87
5.6 Logout ................................................................................................................................................................87
6. FAQs/Troubleshooting .............................................................................................................................................88
4
Glossary of Terms ........................................................................................................................................................92
FCC Statement .............................................................................................................................................................94
Appendix A: Toxic or Hazardous Materials or Elements ..............................................................................................95
5
Welcome
Thank you for purchasing an Amcrest Outdoor PTZ w/ 4x Optical Zoom network camera!
This user manual is designed to be a reference tool for the installation and operation of your IP camera.
Here you can find information about the camera’s features and functions, as well as information to aid in
troubleshooting.
Many of the setup and installation sections below have corresponding videos on YouTube
To access the setup videos, please go to http://amcrest.com/videos
For access to the quick start guide and other support information, go to http://amcrest.com/support
To contact Amcrest support, please do one of the following:



Visit http://amcrest.com/contacts and use the email form
Call Amcrest Support using one of the following numbers
Toll Free: (888) 212-7538
International Callers (Outside of US): +1-713-893-8956
USA: +1-713-893-8956
Canada: 437-888-0177
UK: 203-769-2757
Email Amcrest Customer Support [email protected]
Important Security Warning
In order to keep your Amcrest camera secure and prevent unauthorized access, please make sure to follow the
steps below:

Always make sure that your camera has the latest firmware as listed on
www.amcrest.com/firmware

Never use the default password for your camera. Always ensure that your
password is at least 8-10 characters long and contains a combination of lowercase
characters, uppercase characters as well as numbers.
6
Important Safeguards and Warnings
1．Electrical Safety
All installation and operation should conform to your local electrical safety codes.
The product must be grounded to reduce the risk of electric shock.
We assume no liability or responsibility for any fires or electrical shock caused by improper handling or installation.
2．Transportation Security
Heavy stress, violent vibrations, and excess moisture should not occur during transportation, storage, and
installation of the device.
3．Installation
Handle the device with care.
Do not apply power to the camera before completing installation.
Do not place objects on top of the camera.
4．Repair Professionals
All the examination and repair work should be done by qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or user-attempted repair.
5．Environment
The camera should be kept in a cool, dry place away from direct sunlight, flammable materials, explosive
substances, etc.
This product should be transported, stored, and used only in the specified environments as stated above.
Do not aim the camera at a strong light source, as it may cause overexposure of the picture, and may affect the
longevity of the camera’s sensors.
Ensure that the camera is in a well ventilated area to prevent overheating.
6. Operation and Maintenance
Do not touch the camera sensor or lens directly.
To clean dust or dirt off of the lens, use an air blower or a microfiber cloth.
7. Accessories
Be sure to use only the accessories recommended by manufacturer.
Before installation, please open the package and check to ensure that all of the components are present.
Contact the retailer that you purchased from, or Amcrest directly if anything is broken or missing in the package.
7
1 Features and Specifications
1.1 Overview
The Amcrest Outdoor PTZ w/ 4x Optical Zoom network camera is an excellent tool for digital surveillance that can
be useful to a wide variety of users. The camera connects to any router, and uses an internet connection to allow
the user to access all of its functionality from many internet connected devices. It’s easy to use and can be set up
in a relatively small amount of time. It has various functions such as recording, playback, and monitoring
functionality and it synchronizes audio and video by default.
This Outdoor PTZ w/ 4x Optical Zoom network camera adopts a high-quality design in order to achieve high levels
of reliability and security. It can be configured to work locally, as well as remotely over the internet. The IP2M848E camera works using a POE connection and interfaces with most networks through the POE port of your
router.
1.2 Features
The Amcrest Outdoor PTZ w/ 4x Optical Zoom network camera has the following features:

Network Access
The Outdoor PTZ w/ 4x Optical Zoom network camera connects to a wide variety of routers in order to
connect to the internet, using a wired PoE connection. Once setup, the camera can be accessed remotely
from a wide variety of internet connected devices, including PCs, iPhones, iPads, Android tablets, and
Android phones.

Cloud Storage Functionality
The Outdoor PTZ w/ 4x Optical Zoom network camera is able to record video and audio streams to the
Amcrest Cloud service in order to enable long-term storage for recordings. Amcrest Cloud also allows the
user to easily find and download recorded video for playback from any internet connected PC or Mac
computer.

Advanced Playback Function
This device supports real-time recording and supports searching through recorded footage, fast forward
playback, and downloading of videos and screenshots. The Outdoor PTZ w/ 4x Optical Zoom network
camera can also playback in slow motion, backwards, and frame by frame as needed. When recording, the
Outdoor PTZ w/ 4x Optical Zoom network camera shows a date/time overlay to ensure accurate viewing
of events when they occurred. Lastly, the Outdoor PTZ w/ 4x Optical Zoom network camera can support
video enlargement of certain zones within a stream.

Advanced Network Protocol Support
The Outdoor PTZ w/ 4x Optical Zoom network camera is UPnP compatible, and also includes functionality
for use with PPPoE, DDNS, and other protocols in order to allow remote and local connection with a large
variety of network hardware.
Note: There may be slight differences in functionality due to the existence of different product series.
8
2 Device Overview
The diagram below shows the camera’s front profile.
9
3 Connection & Installation
This section provides information about the connection and installation of the Amcrest Outdoor PTZ w/ 4x Optical
Zoom network camera.
3.1 Connection Guide
The camera initially should be connected via the following method:
The IP2M-848E uses a POE cable for internet access, as well as to power the camera.
3.2 Installation Guide
Note: Prior to installation ensure that the installation environment can support at least 3 times the weight of the
camera.
10
4 Camera Access Setup
This section of the guide will provide the user with information on how to setup access to the camera through any
of the following methods.
4.1 Default Username and Password
To login to the system for the first time, use one of the following default username/password combinations. Once
you’ve successfully logged in, it is highly recommended to change the password for security reasons.
Username: admin
Password: admin
Note: Logging in for the first time will prompt the user to change the password to the admin account.
11
4.2 Camera setup methods
To make your experience with the Amcrest PoE camera easy and simple, we've provided multiple ways to set up,
view, and operate your camera depending on your needs. Please follow the instructions on this page to set up your
camera in the way that works best for you.
4.2.1 Setting up your camera for the first time
If setting up your camera for the first time, please follow the instructions as outlined in section 4.3.1. Using the
Amcrest View app on your smartphone or tablet, you can view your camera live from anywhere, and access
features such as pan/tilt/zoom, recording, taking snapshots, two-way audio, and more.
4.2.2 Accessing your camera using multiple mobile devices
If you followed the app setup instructions in section 4.3.1 to initially set up your camera and would like to add the
camera to another smartphone or tablet, follow the instructions as outlined on section 4.3.3 using your other
devices.
4.2.3 Configuring advanced settings on your camera
If you would like to configure your camera to enable advanced features such as motion detection, e-mail alerts,
FTP, image adjustments, scheduling, and more, please follow the instructions as outlined on section 4.4 (Desktop
access setup).
4.2.4 Using Amcrest Cloud for remote viewing, storage, and playback
Amcrest Cloud is our optional cloud storage and playback service which allows you to access recorded footage
from any device. We offer 4 hours of free storage for your first camera. Please follow the instructions as outlined
on section 4.5 (Amcrest Cloud setup) to sign up for our Amcrest Cloud service and get 4 hours of free storage.
4.2.5 Using plug-and-play for remote web access
AmcrestView.com is a web portal that allows you to view your cameras and recordings quickly and easily from
anywhere in the world using a web browser. Use AmcrestView.com if you need to simply check-in at a moment's
notice. If you would like to use AmcrestView.com, please follow the instructions outlined on section 4.7 (Remote
web access setup).
12
4.3 Amcrest View App Setup
Amcrest PoE cameras enable access through the use of the Amcrest View app on either iOS or Android mobile
operating systems. There are two versions of the app, Amcrest View Lite, and Amcrest View Pro. Amcrest View
(Lite or Pro) on the App Store or Play Store. The Pro version contains features such as push notifications, sharing
video and image files, exporting video in MP4 format, and exporting image files to your phone. The Amcrest Pro
version of the app is now free to download from the Play Store and App Store.
For purposes of this guide, we will use iOS, though both apps have the same interface. The App Interface may
differ slightly from the screenshots below as updates are released. Below, you'll find instructions on how to set up
your camera, as well as instructions on how to configure different settings on your camera such as motion
detection and email alerts. Every major app setup method will be covered in the following sections.
4.3.1 P2P Setup
The P2P Setup method is the method that should always be used to add a camera to your Amcrest View app on a
tablet or smartphone.
Note: Before following the steps below, make sure you have an Ethernet cable connected to your camera’s
Ethernet/PoE port on one end, and connected to an Ethernet/PoE port on a router or switch on the other end.
1.
Download the Amcrest View Pro app from the App Store or Play Store, then open the app.
13
2.
From the home screen, tap the icon in the top
right corner to open the Device List.
3.
Tap the Add Device button.
4.
Tap PoE Camera.
5.
Tap P2P Setup.
14
Note: Move the
camera or the
phone to ensure
that the entire QR
code is visible and
focused in the
frame. In case the
QR code cannot be
scanned, please tap
Enter S/N
Manually to enter
in the camera’s
serial number.
6.
Scan the QR code from the sticker on your
camera.
7.
Double check to ensure that your S/N (Serial
Number) is entered correctly, then tap Next.
9.
Your camera is now ready to go! Tap the Start
Live Preview button to get started!
Note: The default
username is admin
and the default
password is admin.
8.
Give your camera a name, then enter in the
camera’s username and password. Once you’ve
filled out all of the fields, tap Next.
15
4.3.2 App walkthrough
Once you've set up your camera, the app will present you with a popup
that offers a walkthrough of different features. Tap “Yes” on this popup
to begin a tour of all of the icons located on the Live View screen. In the
future, you can always access the walkthrough again by opening the
Menu, tapping Help, then tapping Wizard.
4.3.3 Motion detection setup
Setting up motion detection for the Outdoor PTZ w/ 4x Optical Zoom camera through the Amcrest View app will
allow you to choose how your camera will react to and record motion. This is the best way to record events that
are particularly of interest without needing to waste storage space by constantly recording. However, you can have
motion detection set up along with 24/7 recording. The motion recordings will overlap the regular recordings and
classify each motion-triggered recording as a motion event for your convenience when searching.
There are a lot of customization options for motion detection that can be configured directly through the app. This
gives you complete control over how to make motion detection work the way you want it to.
Here is a list of all the advanced configuration options for motion detection:








Schedule: Modify motion detection recording timings.
Anti-Dither: Set how long motion detection can still be triggered after motion stops.
Sensitivity: Select motion detection sensitivity.
Region Setting: Specify motion detecting regions of the screen.
Record: Toggle this switch to start recording when motion is detected.
Delay: Set how long motion detection recording will continue after a motion event.
Alarm Out: Configure alarm system integration.
Snapshot: Toggle this switch to take snapshot when motion is detected.
Follow the steps below to setup motion detection on your camera.
16
1.
From the home screen, tap the icon in the
top left corner to open the main menu.
2.
Tap Configuration Center to open the
Configuration Center.
3.
Tap Motion Detect to open the motion
detection settings menu.
4.
Select the camera that you want to modify
motion detection settings for.
17
5.
By default, motion detection is enabled. To
configure advanced settings, tap the toggle
switch in the Advanced Config row.
6.
From this screen, you can modify the settings
to fine tune how you use motion detection.
4.3.4 Push notifications setup
Push notifications are an incredibly useful way to get instantly notified of motion events when you’re on the go.
This is a very convenient way to stay connected without having to constantly monitor your live feeds. It allows you
to immediately tune into what’s happening, when it’s happening.
There are several options for configuring exactly how you receive these notifications or “alerts” through your
smartphone as well as options for what type of events trigger a notification.
Note: This feature is only available on the Amcrest View Pro version of the app, which is free to download.
Here is a list of the configuration options for push notifications:





Push Type: Modify what type of push notifications are displayed.
Motion Detect: Enable push notifications for motion detection alerts.
Cam Masking: Enable push notifications for cam masking alerts.
Local Alarm: Enable push notifications for local alarm alerts.
HDD Alarm: Enable push notifications for low hard drive capacity alerts.
18
1.
From the home screen, tap the icon in the
top left corner to open the main menu.
2.
Tap Push Notifications to open the Push
Notifications settings menu.
19
3.
Tap Configuration to open the push
notifications settings menu. Tap Event List to
see a history of past push notifications.
4.
Select the camera that you want to modify
push notification settings for.
5.
Tap your camera’s toggle switch to activate
push notifications and configure settings.
6.
From this screen, you can modify the settings
to fine tune push notifications to your
preference.
20
4.3.5 Email alerts setup
The Amcrest Outdoor PTZ w/ 4x Optical Zoom network camera has the ability to send you email alerts to notify
you when motion detection occurs. This is an alternative to using push notifications, which come directly through
the Amcrest View app. Instead, email alerts can come directly to your email app and can also, of course, be
checked on a computer.
Email alerts can be a great way to keep an email record of all your motion detection activity, instead of the app.
However, keep in mind that email alerts can be set up and used at the same time as having push notifications
active.
It is important to note that, even though you can use the same email address as both the sender and receiver, it is
highly recommended that you create a brand new email (preferably a Gmail) account to use and configure for
email alerts. This will not mean that you have to use and log into two separate emails, because you can forward all
emails from the dedicated email alert account to your main account.
The benefit of doing this is twofold. One, because setting up a new account means you can set up email alerts
without having to adjust or modify any of the security settings on your primary account and can work without a
hitch. Two, because it will prevent your primary email from being flooded by motion detection alert emails. It is
highly recommended that you do not forward your new email alert account to your primary account until you are
satisfied with the sensitivity settings and frequency of motion alerts.
1.
From the home screen, tap the icon in the
top left corner to open the main menu.
2.
Tap Configuration Center to open the
Configuration Center.
21
3.
Tap Email Alerts to open the email alerts
settings menu.
4.
Note: If your
provider is not
listed, select Other,
then fill out the
SMTP Server and
Port fields.
5.
Start by selecting your email provider.
Continue by entering your email address in
the Username field, followed by the
password to your e-mail in the Password
Select the camera that you want to modify
email alert settings for.
Note: You can
specify, in seconds,
the Interval: how
long the camera
should wait
between sending
emails.
6.
Enter a subject line under Subject, then add
Recipients by entering in their email
addresses and tapping the plus sign. Tap the
Email Test button to initiate an email test. If
22
field. Specify the sender email in the Sender
field, then scroll further down.
successful, tap the Save button to save the
email settings.
4.4 Desktop access setup
There are 2 ways to access your camera from a computer (laptop or desktop) which are: locally or remotely.
Note: Before attempting any of the below setup instructions, make sure your camera is connected to the network
via an Ethernet cable and connected to a PoE port.
Local Access: Logging into your camera’s web interface from a computer or laptop device connected to the same
network as your camera (home, office, etc.).
Remote Access: Logging into your camera’s web interface from a computer or laptop device connected to a
network outside of your home or business network (coffee shop, work computer, etc.)
Local access is preferred by those who, for security reasons or personal preference, do not wish to make their
camera accessible from outside their network. However, there are several options available for remote access that
use standardized and secure network protocols including SSL, TLS, DDNS, etc. Most other users require remote
network access by way of their smartphones, tablets, laptops, or computers, for live viewing on the go.
The following section will cover local access and remote access will be covered in section 4.7. It is important to
configure and familiarize yourself with local access before attempting remote access. Keep in mind that any user
can have both local and remote access simultaneously if they so choose.
Before accessing your camera through a web browser, the following two steps must be completed:
1.
You must access the camera’s web interface with its IP address.
2.
You must install the Amcrest web browser plugin.
An IP address is just an identifier given to any devices that connect to a network. People use names, but internetconnected devices use a set of numbers called an IP address to talk to each other. Once you have the IP address,
your computer will be able to find and communicate with your camera.
A browser plugin is just like a translator. By using the camera on your computer through a web browser, you need
to introduce a new piece of software that allows your computer to understand the language that the camera
speaks in a way that a computer can understand. That’s what the browser plugin is for.
To access the camera’s web interface, we will use the Amcrest IP Config Software method.
4.4.1 Amcrest IP Config Software method
Amcrest IP Config Software can be installed for free onto your computer from Amcrest’s official website. The IP
Config Software is available for both Windows and Mac operating systems. To get directly to the downloads page,
use this link: https://amcrest.zendesk.com/hc/en-us/categories/201939038-All-Downloads
23
Otherwise, the steps below will walk you through how to download, install, and use Amcrest IP Config Software:
1.
Log onto your computer, open your web browser of choice, and go to www.amcrest.com/support:
2.
Then, hover over the Support tab up top and choose Downloads from the dropdown.
3.
This brings you to the downloads page. Click the IP Config Software download link on this page for either
Windows or Mac.
4.
Find the download in your Downloads folder, and click it to open the installer.
24
5.
You will be asked to allow this program to make changes to your computer with a pop-up window, click
Yes.
6.
Once you see the first page of the installer wizard, click Next to continue.
7.
On the next page, check the box next to “I agree”, then click Install.
25
8.
After the progress bar completes, if you see a Windows Security Alert popup, click Allow access.
9.
This brings you to the main screen of Amcrest IP Config Software. Your camera will automatically be found
on your network and appear in the list (if properly connected with an Ethernet cable to your router). You
will also see the IP address associated with your camera.
26
The “e” icon to the right allows you to launch directly into your web browser from this screen.
Note: This “e” icon will automatically take your camera’s IP address and use your computer’s “default” web
browser to access and log into your camera. If your default browser is not Internet Explorer, you can write down
the IP address from the Amcrest IP Config Software (IP address located above), open up Internet Explorer yourself,
and type that into the search bar to get to the login screen. Typing your IP address directly into the search bar will
look something like this:
4.4.2 Installing the Amcrest browser plugin
Once you’ve followed one of the above methods to get to the login screen for the camera, follow the below steps
to install the browser plugin on Internet Explorer:
1.
On the main login screen, you should see a popup in the center. Click Install.
2.
An install button will appear on the bottom of the screen for the plugin: webplugin.exe. Click Run, then
go through the prompts of the install wizard.
27
3.
Once you see the notification along the bottom row. Click the small arrow to the right of the Allow
button, and select Allow for all websites.
4.
If you see a popup window asking you to allow the plugin, mark the checkbox next to “Do not show me
the warning for this program again”, then click Allow.
4.4.3 Logging in
Before attempting to gain local access, you will need to make sure the following items are true:
1.
2.
3.
You have your login credentials (if using this local access method as your first, initial choice to setup your
camera, only items 2 and 3 of this list need to be true)
You have located your camera’s IP address
You have installed the Amcrest browser plugin
If you did not follow any of the app setup methods covered in section 4.3, and this is your first time logging into
your camera, please use the following default username and password:
Username: admin
Password: admin
Note: After logging in for the first time, you will be prompted to change your password.
To find the camera’s IP address, please refer to the Amcrest IP Config Software method (section 4.4.1) above.
To install the browser plugin for the camera’s web interface, please refer to the section 4.4.2 above.
28
1.
Take the IP address and type it into the Internet Explorer search bar, then hit ‘Enter’. It should look
something like “http://192.168.1.74:12345/”
2.
3.
Enter your login credentials. You may be prompted to change your password.
(Optional) Save this web page as a Favorite for easy access in the future.
The camera is now successfully set up for live viewing and playback!
For quick and easy remote access on your PC or Mac, please use AmcrestCloud.com (section 4.5) or
AmcrestView.com (section 4.6).
To setup advanced remote access via UPnP/DDNS or Port Forwarding see section 4.7.
If you are still having trouble and would like to watch a video on how to setup the
Outdoor PTZ w/ 4x Optical Zoom camera for local access on a computer/laptop, go to
http://www.amcrest.com/videos, click the Videos tab, then watch the video titled
“Desktop/Laptop Access Setup for ProHD & HDseries WiFi Cameras”.
Note: This is NOT a WiFi camera. However, the steps and process outlined in the above video still correspond to
the setup of this camera.
For additional assistance, please contact us at www.amcrest.com or give us a call at 1-888-212-7538.
4.5 Amcrest Cloud Setup
Amcrest PoE cameras are able to sync with Amcrest Cloud; a service that stores recorded video streams in order to
enable long-term storage. Amcrest Cloud also allows the user to easily find and download recorded video for
playback from any internet connected PC or Mac computer.
29
1.
2.
3.
4.
5.
6.
Connect the camera to a power supply using the included power adapter.
Connect the camera to the internet through a wired PoE connection (see section 3.1).
Using a web browser on your PC or Mac, visit www.amcrest.com/cloud and register for a free account. Once
registered, click the “Add Camera” button. Select “Amcrest”, give the camera a name, and enter the camera’s
SN (located on the bottom of the camera), then click “Next”.
On the settings page, you can adjust optional preferences for your camera. Once settings have been adjusted,
click “Finish”. Your camera is now successfully set up for cloud access and storage.
View your camera live or watch recorded clips using the menu button on the top of the page. You can also use
the Amcrest Cloud app on iOS and Android to add more cameras, play recordings, and view your camera live,
from anywhere.
For additional assistance, please contact us at www.amcrest.com or give us a call at 1-888-212-7538. Step by
step video tutorials available at www.amcrest.com/videos
4.6 Web Access Setup (AmcrestView.com)
You can access your camera through a computer using the P2P web portal AmcrestView.com for quick plug-andplay access. It uses the same technology as the Amcrest View mobile app and is an easy, non-technical setup
method.
There are 2 methods of accessing your camera using AmcrestView.com: the user method (registering an account
for login), and the device method (instant direct access using the serial number).
Both of these methods require that the Amcrest browser plugin be installed for AmcrestView.com.
4.6.1 Installing the AmcrestView.com browser plugin
1.
Open Internet Explorer, type ”www.amcrestview.com” into the search bar, and hit Enter. This will take you to
the login screen:
30
2.
Once you’re on the login page, you will see a message about installing the plugin below the login box. Click
Download Now:
3.
This will take you to another page where you will need to click the Download Now button:
4.
You will be prompted by the browser to install the plugin. Click Run:
5.
You may be prompted to verify this download. This software is not harmful to your computer and will not
make any unwanted changes. To verify, start by clicking View Downloads:
6.
In the View Downloads page, right click the plugin, then click Run Anyway.
31
7.
The plugin will close your browser sessions to install. Save any pages, then click Yes:
8.
On the next prompt, it will say the install was successful and ask you to restart your browser. Click OK:
9.
You will be taken back to the login page and see another notification from your browser asking you to allow
this plugin on this web page. Click the small arrow next to Allow, then click Allow for all websites:
10. Another popup will appear asking you to allow this plugin. Mark the checkbox next to Do not show me the
warning for this program again, then click Allow:
Now the plugin has been installed
successfully and you can continue on
to register for an account for camera
access through AmcrestView.com
32
4.6.2 User method
The user method requires that you first install the Amcrest browser plugin for AmcrestView.com. Then, you can
register for an account to set up your camera.
1.
On the main login screen, www.amcrestview.com, click the Register Now button:
2.
You will be taken to the registration form. Enter your Username, Password, then Confirm Password, type your
Email, enter the Verification Code, make sure the box is checked confirming you’ve read the ‘Amcrest Terms
of Service’, then click Create an Account:
33
3.
You will see the Registration Successful message and a confirmation email will be sent to you:
Check your email, and click the confirmation email from AmcrestView.com:
4.
Once you’ve opened the email, click the confirmation link inside to complete your registration:
34
5.
You will be taken back to AmcrestView.com and shown confirmation that your account has been activated.
Click Go to Login:
6.
You will be taken back to the login screen. Enter your new AmcrestView.com username and password, then
click Login:
7.
A popup will appear from your Windows Firewall. Click Allow access:
35
8.
You will be taken to the main screen of your account. From here, click the Add Device button:
9.
Now you can enter your camera’s information. Enter a Device Name (this can be anything).
Then, fill in the S/N (serial number) this can be found on the sticker attached to the bottom of your camera or
through the web interface (click the “i” icon in the top bar, then click Version).
Enter your username and password for the camera, not the username and password you just created for
AmcrestView.com. To find your camera login credentials, please refer to section 4.4.3. Finally, click OK:
36
10. You will then see your camera added to the device list on the main screen. Click the ‘eye’ icon to view the live
feed:
11. Your browser will give you a notification asking you to allow popups from AmcrestView.com. Click Options for
this site, then click Always allow:
12. You will be taken to the live view page and given a notification to allow the plugin to pull the video feed
through here. Click the small arrow to the right of Allow, then click Allow for all websites:
37
13. A final popup will appear asking you to confirm that you allow this plugin on your browser. Mark the checkbox
next to Do not show me the warning for this program again, then click Allow:
Now you can enable any of your added cameras to see their live feeds. In the top-right panel, there is a channel
list. Click the small square icon to enable your feed for an added camera to see the video feed:
Click the “S” to change it to an “M” which stands for “Main Stream” and will give you a full HD quality video
stream. To go back to “Sub Stream”, for lower quality video (that works better on slower internet connections),
click the “M” and change it to an “S” again.
38
4.7 Remote Web Access Setup
There are two main methods for setting up remote access: UPnP/DDNS, and Port Forwarding.
4.7.1 UPnP/DDNS Remote Web Access Setup
Using Universal Plug and Play (UPnP) and Dynamic Domain Name Server (DDNS) functionality is the easiest way to
setup stable remote access. For this method, your router should support the UPnP networking protocol and the
protocol should be enabled. Please refer to your router manufacturer’s documentation to learn how to enable
UPnP on your router.
Below is a step-by-step walkthrough that details how to setup the Amcrest PoE cameras for Remote Web Access
using UPnP and DDNS:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
Login to your camera’s web interface, open the main menu then go to Setup -> Network.
Using the left hand menu, go to the Connection menu, and write down the HTTP port. It is recommended
to ensure the port number is at least 5 digits long to prevent any port conflicts. If need be, change the
port to a 5 digit number that is less than 65535, note the number down, and click save before proceeding
to the next step.
The system will prompt you to reset the camera. Click OK and wait for the camera to restart.
Restarting the camera may cause the device to use another IP address. Use the included IP Config tool to
find the IP address as detailed in section 4.4.1.
Login to your camera, open the main menu then go to Setup -> Network.
Click the Connections menu item on the left hand menu, and ensure that the HTTP port has changed.
Click the DDNS menu item on the left hand menu, pick Amcrest DDNS from the drop down box, click the
checkbox next to Server Type, and then click the Save button on the bottom right.
To set a custom DDNS name, fill out the Domain Name field and click Save.
Write down the entire Domain Name field, including the white text that says .amcrestddns.com
Click the UPnP menu item on the left hand menu, and click the enable checkbox at the top.
While in the UPnP menu, double click the HTTP port, and change both the internal and external HTTP
ports to match the number that was used in step 2.
Uncheck the last 4 checkboxes in the PAT table on the UPnP menu.
Click apply, then exit this menu to go back to the main menu, then re-enter the UPnP menu, and ensure
the UPnP status says “Mapping Successful”.
Open a web browser and enter in the DDNS domain name address from step 9, enter in a colon, then
type the port number from step 4 on to the end.
a. For example, if the DDNS domain name is http://abc123456789.amcrestddns.com and your
HTTP Port is 33333, the URL would be http://abc123456789.amcrestddns.com:33333
The browser may prompt you to install a plugin. Click install to download the plugin, and then click on the
plugin installation file to install the plugin.
If the browser prompts you to allow the plugin to work on the computer, hit Allow to ensure the plugin
can run successfully.
Enter in login details into the username and password fields and click login.
39
If the process above is not working, please contact Amcrest Support via one of the following options:



Visit http://amcrest.com/contacts and use the email form
Call Amcrest Support using one of the following numbers
Toll Free: (888) 212-7538
International Callers (Outside of US): +1-713-893-8956
USA: (888) 212-7538
Canada: 437-888-0177
UK: 203-769-2757
Email Amcrest Customer Support [email protected]
4.7.2 Port Forwarding Remote Web Access Setup
Port Forwarding is an alternative method to setting up remote access for Amcrest PoE cameras. This method
should only be used if the UPnP/DDNS Remote Access method did not work.
Below is a step-by-step walkthrough that details how to setup the camera for Remote Web Access using Port
Forwarding:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
Login to your camera, open the main menu then go to Setup -> Network.
Open the TCP/IP settings screen.
By default, the camera has the mode set to DHCP. Ensure that DHCP is selected. The IP Address, Subnet
Mask, Default Gateway, Preferred DNS, and Alternate DNS should all be 0s if DHCP is selected.
Click Save to save these settings. This should now open the main menu.
From the main menu, go to Setup -> Network.
On the TCP/IP settings screen, the IP Address, Subnet Mask, Default Gateway, Preferred DNS, and
Alternate DNS should all be populated.
Click the radio button next to Static, to change the mode to Static.
Write down the IP Address that is currently in the IP address field.
Click the Save button.
Using the left hand menu, go to the Connection menu, and write down the TCP, UDP, and HTTP port
number. It is recommended to ensure that these port numbers are at least 5 digits long to prevent any
port conflicts. If need be, change each of these port numbers to a 5 digit number that is less than 65535,
note the numbers down, and click save before proceeding to the next step.
Go to http://www.canyouseeme.org/ and check to ensure each of the port numbers specified in step 10
is open.
Write down the manufacturer name, brand, and model name for the router that the camera is connected
to, and then proceed to http://www.portforward.com on your web browser.
Open the port forwarding guide section on the left hand side menu.
Find the router brand name in the list, and click it.
Find the router model number, and click it.
Click the Default Guide link near the middle of the page.
This guide will help you take the step necessary to port forward on the router. Follow these steps, and
then return to the camera.
Login to your camera, open the main menu then go to Setup -> Network.
Click the DDNS menu item on the left hand menu, pick Amcrest DDNS from the drop down box, click the
checkbox next to Server Type, and then click the Save button on the bottom right.
To set a custom DDNS name, fill out the Domain Name field and click Save.
Write down the entire Domain Name field, including the white text that says .amcrestddns.com
40
22. Open a web browser and enter in the DDNS domain name address from step 21, enter in a colon, then
type the HTTP port number from step 10 on to the end.
a. For example, if the DDNS domain name is http://abc123456789.amcrestddns.com and your
HTTP Port is 33333, the URL would be http://abc123456789.amcrestddns.com:33333
23. Enter in login details into the username and password fields and click login.
If the process above is not working, please contact Amcrest Support via one of the following options:



Visit http://amcrest.com/contacts and use the email form
Call Amcrest Support using one of the following numbers
Toll Free: (888) 212-7538
International Callers (Outside of US): +1-713-893-8956
USA: (888) 212-7538
Canada: 437-888-0177
UK: 203-769-2757
Email Amcrest Customer Support [email protected]
4.8 NVR Access
The camera supports connecting to any NVR that uses the ONVIF standard. This allows the camera to view live
playback and to save recorded data to a network storage device. To connect to an NVR, use an Ethernet cable to
link the camera to the NVR.
41
5 Operation and Interface
This section of the manual details the camera’s interface, as well as all of the operations the camera can perform.
The main interface of the camera contains 6 major tabs on the top of the screen. By default, the interface opens on
the Live tab.
5.1 Live
The Live tab allows the user to see a live video feed from the camera. The live tab has 4 main sections:
42
Section 1: This bar allows the user to select which stream type and which protocol they want to choose. For more
information on stream types, see section 5.4.1.2.1. For more information on protocols, see section 5.4.2.2.1.
Section 2: The functions bar allows the user to perform different camera functions while in live mode. See the
table below for an explanation of the different functions available:
Button
Function Name
Alarm Output
Function Description
Click this button to generate an alarm output signal. This button becomes
red/grey depending on alarm output activation or cancellation.
Digital Zoom
Click this button to activate the zone selection function. This allows the
user to use the mouse to select a zone to zoom in on.
Snapshot
Click this button to take a screenshot of the live feed. The picture is saved
at the path specified in Setup -> Camera -> Video -> Path.
Triple Snapshot
Click this button to take 1 screenshot per second for 3 seconds. The
pictures are saved at the path specified in Setup -> Camera -> Video ->
Path.
Click this button to manually record video. The video is saved at the path
specified in Setup -> Camera -> Video -> Path.
Manual Record
Audio
Bidirectional Talk
Help
Click this button to enable or disable audio output from the camera. This
feature allows the user to listen in on the audio the camera’s microphone
is picking up.
Click and hold this button to enable bidirectional talk. This feature allows
the user to broadcast audio from their computer to the camera. While this
is active, the camera’s speaker is shut off in order to keep audio quality
high.
Click this button to open a window that details the buttons and functions
shown on this screen.
Section 3: This bar allows the user to change video settings for the live playback screen. See the below table for an
explanation of the video settings:
Button
Function Name
Image Adjustment
Adapt/Original Size
Full Screen
Width/Height Ratio
Stream Fluency
Function Description
This button opens the image adjustment toolbar, which allows the user to
adjust brightness, contrast, saturation, and hue for the live feed’s picture.
This button allows the user to switch between displaying the original size
of the stream in its set resolution, or to adapt to the size of the monitor
display the feed is being viewed on.
This button allows the user to make the live feed go into full screen mode.
Double click the mouse or click the ESC button to exit full screen mode.
This button allows the user to change the width/height ratio for the live
feed. The options are Original and Adaptive. Original uses the aspect ratio
of the stream’s set resolution, and adaptive fits the feed to the aspect
ratio of the monitor display the feed is being viewed on.
This button allows the user to change the stream fluency. There are 3
options. Realtime reduces delay and decreases fluency, and Fluency has a
larger delay but the video stream becomes more fluid.
Section 4: This section of the Live tab shows the picture that the camera is broadcasting. The bitrate is shown in
the top left corner, the native resolution is shown in the top right corner, the time stamp is shown below the
native resolution, and the camera type is shown in the bottom left corner.
43
5.2 PTZ
The PTZ tab allows the user to change the position of the camera. Below is a screenshot of the PTZ tab:
The PTZ control panel allows the user to position the camera in different ways. Below is a screenshot of the PTZ
control panel:
The arrows on the PTZ control panel allow the user to move the camera’s position in a specific direction. The
button in the middle of the direction arrow allows the user to select an area in the live view to zoom in on.
44
The speed dropdown box allows the user to control the speed at which the camera moves. The values range from
1 to 8, 8 being the fastest.
The zoom buttons allow the user to digitally zoom in and out on the live preview picture.
The dropdown box under PTZ settings allows the user to configure Presets and Tours. Preset allows the user to
designate specific PTZ positions for the camera. To create and manage presets, follow the steps below:




Configure the camera positioning as needed.
Input the preset number, and then click the + Add button
Click - Del to delete the current preset.
Click Go To to access a preset.
Tour allows the user to string multiple presets together. To create and manage tours, follow the steps below:






Ensure you have more than 1 preset configured already.
Input the tour value and click Start.
Input the preset value and then click the Add Preset button to add a preset.
Continue adding presets as needed.
Click Del Preset to remove a preset from the tour.
Click - Del to delete the entire tour.
5.3 Playback
The Playback tab allows the user to playback the camera’s recorded video. Below is a screenshot of the Playback
tab:
This is the interface for the playback menu. There are 7 main sections:
45
1.
Quick Actions: This panel allows the user to zoom in on playback footage, take a snapshot of the playback
footage, or open the help menu.
2. File Menu: This panel allows the user to select a file type and data source.
3. Calendar: This panel allows the user to pick a date that they would like to playback video from. When a date
has recorded footage available, it’s green. The current date is blue, unless it has recorded footage, then it’s a
lighter green.
4. File List: This button opens a file list of all recorded video for a specific date range. From here, the user can
download these videos to their PC.
5. Trim Panel: This panel allows the user to trim playback video for download. By specifying time stamps, the
user can trim down.
6. Recorded Video Panel: This panel allows the user to specify what type of video they would like to playback
and it also allows the user to select where to start playback from. The buttons on the bottom right allow the
user to select a zoom level.
7. Playback Bar: This panel allows the user to control playback. It also allows the user to control playback speed,
and playback volume.
Clicking the File List opens the following screen on the sidebar:
This allows the user to select files for download. Select the files by clicking the checkbox next to each file, and then
click
to download the files to the PC.
46
5.4 Setup
The Setup tab allows the user to change different camera settings. Below is a screenshot of the setup tab:
There are 3 main sections to note in the Setup tab:
1.
2.
3.
Menu Bar: The menu bar is composed of menu sections, which when clicked display any menu items that fall
under their category.
Menu Items: These menu items each open up a different menu that allows the user to change specific settings
for the camera.
Menu Tab: These tabs open up menu options for certain menu items.
Note: To view additional information about any of the information in the menu, click the
the top right corner.
button near
In the rest of section 5.4, we will be exploring all of the different menus that are available through web access.
47
5.4.1 Camera
This menu section allows the user to change different camera settings for video, audio, and to manage image
profiles.
5.4.1.1 Configuration
This menu allows the user to configure image profiles for normal, day, and night usage.
5.4.1.1.1 Configuration
Below is a screenshot that shows the Configuration tab in the Configuration menu item:
Below is an explanation for each of the fields on the Configuration tab in the Configuration menu item:
 Profile: This dropdown box allows the user to select which profile to modify. The 3 options are Day, Night, and
Normal.
 Brightness: This slider is used to adjust playback and recorded video window brightness. The value ranges
from 0 to 100. The default value is 50. The larger the number, the brighter the video is. When you input the
value here, the bright section and the dark section of the video will be adjusted accordingly. You can use this
function when the whole video is too dark or too bright. Please note the video may become hazy if the value is
too high. The recommended value ranges from 40 to 60.
 Contrast: This slider is used to adjust playback and recorded video window contrast. The value ranges from 0
to 100. The default value is 50. The larger the number is, the higher the contrast is. You can use this function
when the whole video brightness is OK but the contrast is not correct. Please note the video may become hazy
if the value is too low. If this value is too high, the dark section may lack brightness while the bright section
may over expose. The recommended value ranges from 40 to 60.
 Saturation: This slider is used to adjust playback and recorded video window saturation. The value ranges
from 0 to 100. The default value is 50. The larger the number, the stronger the color is. This value has no
48















effect on the general brightness of the whole video. The video color may become too strong if the value is too
high. For the grey part of the video, distortion may occur if the white balance is not accurate. Please note the
video may not be clear if the value is too low. The recommended value ranges from 40 to 60.
Sharpness: This slider is used to adjust the sharpness of the video. The value ranges from 0 to 100. The larger
the value is, the clearer the edges are and vice versa. Note: The higher the value, the higher likelihood of
picture noise occurring. The default value is 50 and the recommended value ranges from 40 to 60.
Gamma: This slider is used to adjust the gamma of the video. The larger the number, the brighter the video is.
The default value is 50 and the recommended value ranges from 40 to 60.
Anti-Flicker: These radio buttons allow the user to select what type of anti-flicker technology should be used
for the video feed. The three options are 50 Hz, 60 Hz, and Outdoor. The desired option should offset any
flickering effect caused by the electrical current used in the specific area.
Exposure: This dropdown box allows the user to select the exposure type for the video feed. The options are
Auto, Low Noise, Low Motion Blur, and Manual. When low noise is selected, an additional option to specify a
gain range appears below this box. When low motion blur is selected, an additional option to specify shutter
speed appears below this box. When manual is selected, additional options to specify a shutter speed and a
gain range appear below this box.
White Balance: This dropdown box allows the user to select the white balance for the video feed. The
different options are Auto, Sunny, Night, Outdoor, and Customized. Selecting customized opens a menu that
allows the user to set specific red or blue values.
Day & Night: This dropdown box allows the user to select which type of picture is displayed. The options are
Color, Auto, and Black & White.
D&N Sensitivity: This option allows the user to change the Day/Night Sensitivity of the camera. The three
options are Low, Middle, and High. The higher the sensitivity, the quicker the camera will change into another
mode depending on the light levels.
D&N Delay: This dropdown box allows the user to set a delay in seconds for how long it takes to switch
between Day and Night modes. The values range from 2 seconds to 10 seconds.
BLC Mode: This dropdown box allows the user to select Back Light Compensation. The values are Off, BLC
(Auto), WDR, and HLC. This feature should only be used in black lit environments.
Indicator Light: This dropdown box allows the user to select whether the indicator light on the back of the
camera is on or off for the selected profile.
Mirror: This radio button allows the user to turn the mirroring feature on or off. Turning mirroring on will
mirror the picture.
Flip: This dropdown box allows the user to flip the video feed picture. Flipping the picture is recommended
only if the camera is mounted upside down.
3D NR: This radio button allows the user to turn the 3D Noise Reduction feature on or off.
3D NR Level: This slider allows the user to specify the 3D Noise Reduction level. The value ranges from 1-100.
Night Vision: This dropdown box allows the user to select whether the camera turns on night vision
automatically or if night vision remains off.
To reset to default settings, click the Reset Defaults button. To cancel any modifications, click the Cancel button. To
save the settings, click the Save button.
49
5.4.1.1.2 Profile Management
Below is a screenshot that shows the Profile Management tab in the Configuration menu item:
Below is an explanation for each of the fields on the Profile Management tab in the Configuration menu item:
 Profile Management: This set of radio buttons allow the user to set what basis the profile management
settings run on. There are 3 options: Normal, Full Time, and Schedule. Normal means that the system can
automatically alternate between night and day based on the profiles for each. Full Time means that the
system sticks to one profile the entire time it is running. Schedule allows the user to dictate which times of the
day are designated for the day profile and the night profile.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
50
5.4.1.2 Video
This section allows the user to change video settings for the camera’s video feed. There are 4 tabs in this menu
item: Video, Snapshot, Overlay, and Path.
5.4.1.2.1 Video
Below is a screenshot that shows the Video tab in the Video menu item:
Below is an explanation for each of the fields on the Video tab in the Video menu item:
 Code-Stream Type: This dropdown box allows the user to select different encode frame rates for different
recorded events. This includes the main stream, motion stream, and alarm stream. The camera supports
active control frame function (ACF). It allows the user to record in different frame rates. For example, a high
frame rate can be used to record important events, and a low frame rate can be used to record scheduled
events. The camera also allows for the option to set different frame rates for motion detection recordings and
alarm recordings.
 Encode Mode: This dropdown box allows the user to select a compression protocol. The system supports
H.264 and MJPEG video compression protocols.
 Resolution: This dropdown box allows the user to set the resolution. The system supports various resolutions
and they can be selected from this dropdown list.
 Frame Rate (FPS): This dropdown box allows the user to select a frame rate. Frame rate settings are measured
in frames per second (FPS), and can range from 1f/s to 25f/s in PAL mode and 1f/s to 30f/s in NTSC mode.
 Bit Rate Type: This dropdown box allows the user to select a bit rate type. The system supports two bit rate
types: CBR and VBR. In VBR mode, video quality can be set.
 Reference Bit Rate: This is the recommended bit rate value according to the resolution and frame rate
selected.
 Bit Rate: This dropdown box allows the user to select a bit rate.
 Frame Interval: This field allows the user to set the P frame amount between two I frames. The value ranges
from 1 to 150 seconds. Default value is 50. Recommended value is frame rate *2.
 Watermark Settings: This function allows the user to verify if the video has been tampered with.
51

Watermark Character: This field allows the user to set the watermark’s text. The default string is DigitalCCTV.
The maximum length is 85 characters. This string can only include numbers, characters, and underscores.
Sub Stream is a lower quality stream that allows the feed to take up less resources and bandwidth when
streaming. The Main Stream and the Sub Stream have the same fields. Sub Stream can be enabled by checking the
box next to Enable.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
5.4.1.2.2 Snapshot
Below is a screenshot that shows the Snapshot tab in the Video menu item:
Below is an explanation for each of the fields on the Snapshot tab in the Video menu item:
 Snapshot Type: This dropdown box allows the user to select a snapshot mode. There are two snapshot modes:
general and event. General snapshots are taken as scheduled. Event snapshots occur when a motion detection
alarm or a tampering alarm is triggered.
 Image Size: This dropdown box shows the image size. By default the screenshot size is the same size as the
video feed’s resolution.
 Quality: This dropdown box allows the user to select image quality. Quality is adjusted on a scale of 1-6.
 Interval: This is to set snapshot frequency. The value ranges from 1 to 7 seconds. The maximum setting for a
customized interval is 3600s/picture.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
52
5.4.1.2.3 Overlay
Below is a screenshot that shows the Overlay tab in the Video menu item:
The menu on the left allows the user to select which overlay to modify. Privacy Masking, Channel Title, Time, and
Text Overlay can all be modified in this menu.
For Privacy Masking, the radio button enables or disables the feature. To set a privacy mask, click one of the boxes
in the live view window, and position or resize it as needed. To remove a box, click on it, then click the delete
button. To remove all privacy filter boxes, click the remove all button.
For Channel Title, the radio button enables or disables the feature. The Input Channel Title field allows the channel
title to be modified.
For Time, the radio button enables or disables the feature. Clicking the Display Weekdays checkbox will show the
weekday at the end of the timestamp.
For Text Overlay, the radio button enables or disables the feature. The Input Text box allows the user to enter
multiple lines of text as needed, and the Text Alignment dropdown box allows the user to align the text either right
or left.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
53
5.4.1.2.4 Path
Below is a screenshot that shows the Path tab in the Video menu item:
Below is an explanation for each of the fields on the Path tab in the Video menu item:
 The Live Snapshot field allows the user to select where to save live snapshots to. Click the Browse button to
select a different destination folder.
 The Live Record field allows the user to select where to save live recordings to. Click the Browse button to
select a different destination folder.
 The Playback Snapshot field allows the user to select where to save playback snapshots to. Click the Browse
button to select a different destination folder.
 The Playback Download field allows the user to select where to save playback video downloads to. Click the
Browse button to select a different destination folder.
 The Video Clips field allows the user to select where to save video clips to. Click the Browse button to select a
different destination folder.
To reset to default settings, click the Reset Defaults button. To save the settings, click the Save button.
5.4.1.3 Audio
This menu allows the user to modify audio settings for the camera. Below is a screenshot that shows the Audio
menu item under the Camera menu section:
54
Below is an explanation for each of the fields on the Audio menu:
 Enable: This checkbox allows the user to enable audio recording.
 Encode Mode: This dropdown box allows the user to select what audio format the audio should be recorded
in.
 Sampling Frequency: This dropdown box allows the user to select a sampling frequency for the audio. The
options are 8k and 16k. 16k audio sampling allows for higher sound quality.
 Audio In Device: This field allows the user to select what source to get audio from. The default is the camera’s
built-in mic. Alternatively, the line in mic can be selected.
 Noise Filter: This dropdown box allows the user to enable or disable the audio noise filter function. This
function provides cleaner audio quality when enabled.
 Microphone Volume: This slider allows the user to select the microphone volume. The value ranges from 0 to
100. The default value is 50.
 Speaker Volume: This slider allows the user to select the speaker volume. The value ranges from 0 to 100. The
default value is 50.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
5.4.2 Network
This menu section allows the user to change network settings for the camera.
5.4.2.1 TCP/IP
The TCP/IP menu item has two tabs: TCP/IP and P2P.
5.4.2.1.1 TCP/IP
TCP/IP stands for Transmission Control Protocol/Internet Protocol and it is the language/protocol that allows
communication between internet connected devices, whether on a local network, or a on the Internet at large.
This screen allows for TCP/IP settings to be modified in order for the camera to establish a connection to the
network. Below is a screenshot of the TCP/IP settings tab:
55
Below is an explanation of the fields on the TCP/IP settings tab:
 Host Name: This text field allows the user to change the host device name for the camera. This field supports
a maximum of 15 characters.
 Ethernet Card: This dropdown box allows the user to select which internet access device to use. If the device is
connected to a wired connection and a wireless one at the same time, then this box will have options to pick
either of the connections. The Set as Default button allows the user to select one of the connection methods
as the default one.
 Mode: Static vs DHCP: This radio button allows the user to choose between a static IP address, and a dynamic
IP address. DHCP stands for Dynamic Host Configuration Protocol, and this enables the camera to
automatically obtain an IP address from another network device such as a server or more commonly, a router.
When the DHCP function is enabled, the user cannot modify the IP address, Subnet Mask, or Default Gateway,
as these values are obtained from the DHCP function. To view the current IP address, DHCP needs to be
disabled. Note: When PPPoE is enabled, modification of the IP Address, Subnet Mask, and Gateway becomes
prohibited.
 MAC Address: This field shows the camera’s MAC address, which is unique to this device. This number is readonly and is used to access a local area network (LAN).
 IP Version: This dropdown allows the user to select the IP version. The two options are IPV4 and IPV6.
 IP Address: This field allows the user to enter a custom IP address.
 Subnet Mask: This field allows the user to enter a custom subnet mask.
 Default Gateway: This field allows the user to enter a custom default gateway.
 Preferred DNS Server: This field allows the user to enter the preferred DNS server IP address.
 Alternate DNS Server: This field allows the user to enter the alternate DNS server IP address.
 Enable ARP/Ping to set IP Address Service: This checkbox allows the user to enable the ARP/Ping service to
change the IP address service. For more information on this feature, click the help button while on the TCP/IP
settings tab.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
5.4.2.1.1 P2P
The P2P settings screen is where users can use a QR code to connect their smartphone or tablet to the camera.
This feature needs to be enabled for use with the Amcrest View app, Amcrest Cloud, or AmcrestView.com. Below
is a screenshot of the P2P settings tab:
56
Below is an explanation of the fields on the P2P settings tab:
 Enable: This checkbox allows the user to enable the P2P feature for the camera. This feature must be enabled
for the camera to connect to a smartphone or tablet via the Amcrest View app. It is enabled by default.
 Status: This field displays the status of the P2P connection. Once the camera is connected to a device, this
field should display the word Online.
 S/N: This field displays the Token ID for the camera. The Token ID can be used to manually enter the camera’s
information on a mobile or tablet device in case the QR code scanning feature cannot be used.
 QR Code: This image is a Quick Response (QR) code. By scanning this image using the Amcrest View app, this
camera can establish a connection with the app.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
5.4.2.2 Connection
The Connection menu item has two tabs: Connection and ONVIF.
5.4.2.2.1 Connection
The Connection tab is where users can configure port connections. Below is a screenshot of the Connection
settings tab:
Below is an explanation of the fields on the Connection settings tab:
 Max Connections: This field allows the user to specify the maximum amount of users that can be connected to
the camera at the same time. The maximum number of users the camera can support at one time is 20.
 TCP Port: This field designates the Transmission Control Protocol (TCP) port number. The default value is
37777.
 UDP Port: This field designates the User Datagram Protocol (UDP) port number. The default value is 37778.
 HTTP Port: This field designates the Hypertext Transfer Protocol (HTTP) port number. The default value is 80.
 RTSP Port: This field designates the Real Time Streaming Protocol (RTSP) port number. The default value is
554.
 HTTPS: This checkbox enables the use of the HTTPS protocol for accessing the camera.
 HTTPS Port: This field designates the Hypertext Transfer Protocol Secure (HTTPS) port number. The default
value is 443.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
57
5.4.2.2.2 ONVIF
The ONVIF tab is where users can configure authentication via the ONVIF standard. Below is a screenshot of the
ONVIF settings tab:
To enable ONVIF, click the radio button next to Enable, and then click the save button.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
5.4.2.3 PPPoE
PPPoE stands for Point-to-Point Protocol over Ethernet. This screen allows users to configure PPPoE connections.
Below is a screenshot of the PPPoE screen:
To enable PPPoE, click the enable checkbox, and fill in the username and password fields, then click Save.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
58
5.4.2.4 DDNS
DDNS stands for Dynamic Domain Name Server. This technology is used to automatically update name servers in
real time in order to help the camera maintain a persistent address despite changes in location or configuration.
What this means is that even when the camera is restarted, moved, or reconfigured, it can keep the same IP
address, thus allowing remote users uninterrupted access to the camera, rather than having to request a new IP
address to use for remote access anytime a change is made.
To use this feature, users will need to setup an account with a DDNS service. The camera supports a variety of
DDNS services such as AmcrestDDNS, Quick DDNS, NO-IP DDNS, CN99 DDNS, and Dyndns DDNS. Based on which
service is selected, different options may show on this screen. For purposes of this guide, AmcrestDDNS will be
used. AmcrestDDNS is a free DDNS service provided by Amcrest, and it must be renewed every year. A renewal
reminder email will be sent to the email entered in the username field below.
To configure the camera for DDNS access using AmcrestDDNS, see section 4.7.1. Below is a screenshot of the DDNS
settings screen, configured to AmcrestDDNS:
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
59
5.4.2.5 IP Filter
This screen allows for the filtering of IP addresses, either blocking them, or granting them access to the camera.
This feature helps make the camera more secure by limiting remote access only to approved users. Below is a
screenshot of the IP Filter screen:
Below is an explanation of fields on the IP Filter settings screen:
 Trusted Sites: This checkbox allows the user to enable the IP Filter feature for trusted sites.
 Add IP/MAC: This button opens a popup that allows the user to add IP or MAC addresses to the trusted site
list. Note: When accessing the camera externally, please add the MAC address of the router on the PC end.
 Remove All: This button allows the user to remove all sites from the trusted IP/MAC list.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
60
5.4.2.6 SMTP (Email)
This screen allows for the configuring of email settings in order to permit the camera to send emails when an alarm
is triggered. Below is a screenshot of the email settings screen:
Below is an explanation of fields on the SMTP (Email) settings screen:
 SMTP Server: SMTP stands for Simple Mail Transfer Protocol. This field allows the user to enter the SMTP
server used by the email service.
 Port: This field allows the user to enter the port that corresponds to the selected SMTP server.
 Login Anonymously: This checkbox allows the user to anonymously login to the server.
 Username: This field allows the user to enter the SMTP username.
 Password: This field allows the user to enter the password associated with the SMTP username.
 Sender: This field allows the user to enter the sender email address. This email address will be the one that
sends out all emails pertaining to the alerts and alarm emails sent by the camera.
 Authentication: This dropdown box allows the user to select an encryption type. There are two types of email
encryption protocols that are available.
o SSL: Secure Socket Layer
o TLS: Transport Layer Security
 Subject: This field allows the user to define the subject line of the email that is sent to the receivers.
 Recipients: This field allows the user to enter the receiver email address. These email addresses are the ones
that will receive any emails pertaining to alert and alarm emails sent by the camera. Up to 3 email addresses
can be entered in this field.
 Interval: This field allows the user to define, in seconds, how long the system should wait between sending
emails. This prevents multiple emails from being sent out.
 Keep Alive: This checkbox allows the user to enable a function to periodically check in with the SMTP server to
ensure it can connect correctly.
 Email Test: This button causes the system to automatically send out an email to test the connection is OK or
not. Prior to the email test, please save the email setup information.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
61
5.4.2.7 UPnP
UPnP stands for Universal Plug and Play, and it is a protocol used to easily connect devices to the internet. In the
case of this camera, it allows the camera to connect to the router in an easy manner to quickly allow for remote
access. Below is a screenshot of the UPnP settings screen:
Below is an explanation of fields on the UPnP settings screen:
 Enable: This checkbox allows the user to enable the UPnP function.
 Router State: This field shows the UPnP status and has two options:
o Unknown: This means that UPnP mapping has failed.
o Successful: This means that UPnP mapping has succeeded.
 Port Mapping List: This table is used to show how the ports for each protocol listed below have been
remapped by the UPnP protocol.
o The first column shows the checkboxes to enable the corresponding service on the table.
o The second column shows the name of the services. To edit this, double click on the service line item.
o The third column shows the name of the protocol used by that service. To edit this, click the pencil
button in the modify column for that line item.
o The fourth column shows the Internal Port used by that service to establish communication from the
router to the camera. To edit this, click the pencil button in the modify column for that line item.
o The fifth column shows the External Port used by that service to establish communication from the
router to the internet. To edit this, click the pencil button in the modify column for that line item.
o The sixth column shows the status of the protocol. If the protocol was mapped successfully, this field
will say “Mapping Succeeded”.
o The seventh column allows the user to open a dialog box and edit the service’s information.
To see how to setup the camera for remote access, see section 4.7.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
62
5.4.2.8 SNMP
SNMP stands for Simple Network Management Protocol. This protocol is used to provide a basic framework in
order to allow connection between various network devices. Below is a screenshot of the SNMP settings screen:
Below is an explanation of fields on the SNMP settings screen:
 SNMP Version: These checkboxes allow the user to select the SNMP version to use.
 SNMP Port: This field allows the user to write in a port for SNMP to use. The port can range from anywhere
from 1 to 65535.
 Read Community: This field shows which SNMP community has read access.
 Write Community: This field shows which SNMP community has write access.
 Trap Address: This field allows the user to write in a trap address.
 Trap Port: This field allows the user to write in a trap port number. The trap port number should not be the
same as the SNMP port.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
5.4.2.9 Bonjour
Bonjour is Apple's implementation of Zero-configuration networking (Zeroconf), a group of technologies that
includes service discovery, address assignment, and hostname resolution. Below is a screenshot of the Bonjour
settings screen:
63
Click the checkbox next to Enable to the Bonjour functionality. The Server Name field allows the user specify what
name to use in order to connect devices via the Bonjour protocol.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
5.4.2.10 Multicast
Multicast is a feature that enables the camera to broadcast its live view to multiple computers on the same
network. Below is a screenshot of the multicast screen:
Below is an explanation of the fields in the Multicast settings screen:
 Enable: This checkbox allows the user to enable Multicast functionality.
 Multicast Address: This field allows the user to enter a multicast address.
 Port: This field allows the user to enter a multicast port.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
5.4.2.11 802.1x
802.1x is an authentication method for connecting to a network. Below is a screenshot of the 802.1x screen:
To enable 802.1x, click the checkbox next to Enable. An authentication method can be chosen from the dropdown
box, and a username and password can be entered in their respective fields.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
64
5.4.2.12 QoS
QoS stands for Quality of Service and it refers to the overall performance of a computer network, particularly the
performance seen by the users of the network. Below is a screenshot of the QoS screen:
Below is an explanation of the fields on the QoS screen:
 Realtime Monitor: This field allows the user to enter in a priority value for realtime monitoring packets. The
range is between 0-63.
 Command: This field allows the user to enter in a priority value for command packets. The range is between 063.
 Open the WMM: This checkbox allows the user to open the WiFi MultiMedia (WMM) options.
Note: WMM is not supported on this model.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
65
5.4.3 Event
This menu section allows the user to change different settings for triggering events.
5.4.3.1 Video Detection
The video detection menu has two tabs: Motion Detect and Video Tamper.
5.4.3.1.1 Motion Detect
This tab allows the user to modify motion detection settings. Below is a screenshot of the Motion Detect tab:
Below is an explanation of the fields on the Motion Detect tab:
 Enable: This checkbox enables motion detection for the camera.
 Working Period: Clicking this button opens a weekly schedule that can be used to set times.
o

Click and drag to set motion detection for certain days of the week. Also, periods of motion detection
can be set for each day and enabled using the period settings on the bottom half of the screen. There
are a total of 6 periods that can be set.
Anti-Dither: This field allows the user to set the anti-dither time. The values in this field can range from 5 to
600 seconds. This time value controls how long the alarm signal lasts. Based on motion detection, a buzzer can
go off, a tour can begin, PTZ can be activated, a snapshot can be taken, or the camera can begin recording.
o For example, if the anti-dither time is set to 10 seconds, each alarm may last 10 seconds if the local
alarm is activated. During the process, if the system detects another local alarm signal at the fifth
second, the buzzer, tour, PTZ activation, snapshot, record channel functions will begin another 10
seconds while the screen prompt, alarm upload, email will not be activated again. After 10 seconds, if
66

system detects another alarm signal, it can generate a new alarm since the anti-dither time has
expired.
Detection Area: Clicking this button opens a pop up screen that can be used to set detection areas.
o







When the setup button is clicked, a live stream of the video is shown. The user can then set up to 4
regions, each with their own region name, sensitivity (1-100), and threshold (1-100). Each region has
a specific color, and the region selector tool is displayed when the mouse is moved to the top of the
screen.
 Sensitivity is the amount of change required to increase the motion detected by a
percentage. The lower the sensitivity, the more movement is required to trigger an alarm.
 Threshold is the level that the motion detection needs to reach in order to trigger an alarm.
The lower the threshold, the more likely that motion will trigger an alarm.
o To designate a zone, click and drag the mouse over the area desired. When a colored box is displayed
over the live feed, that area is now enabled for motion detection.
o After the motion detection zone is set, click the enter button to exit the motion detection screen.
Remember to click the save button on the motion detection settings screen, otherwise the motion
detection zones will not go into effect. Clicking the cancel button to leave the motion detection zone
and will not save the zone setup.
Record: This checkbox allows the user to enable the camera to record video when a motion detection alarm is
triggered.
Record Delay: This field specifies in seconds how long the delay between alarm activation and recording
should be.
Relay Out: This checkbox allows the user to enable the camera to trigger a connected alarm (connected to the
alarm port on the back of the camera) when a motion detection alarm is triggered.
Alarm Delay: This field specifies in seconds how long the delay between alarm activation and Relay alarm
activation should be.
Send Email: This checkbox allows the user to enable the camera to send an email when a motion detection
alarm is triggered.
PTZ: This checkbox allows the user to enable the camera to activate a PTZ tour when a motion detection alarm
is triggered.
Snapshot: This checkbox allows the user to enable the camera to take a snapshot when a motion detection
alarm is triggered.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
67
5.4.3.1.2 Video Tamper
This tab allows the user to modify video tamper settings. Below is a screenshot of the Video Tamper tab:
Below is an explanation of the fields on the Video Tamper tab:
 Enable: This checkbox enables a video tamper alarm for the camera.
 Working Period: Clicking this button opens a weekly schedule that can be used to set times.
o







Click and drag to set video tampering for certain days of the week. Also, periods of video tampering
can be set for each day and enabled using the period settings on the bottom half of the screen. There
are a total of 6 periods that can be set.
Record: This checkbox allows the user to enable the camera to record video when a video tampering alarm is
triggered.
Record Delay: This field specifies in seconds how long the delay between alarm activation and recording
should be.
Relay Out: This checkbox allows the user to enable the camera to trigger a connected alarm (connected to the
alarm port on the back of the camera) when a video tamper alarm is triggered.
Alarm Delay: This field specifies in seconds how long the delay between alarm activation and Relay alarm
activation should be.
Send Email: This checkbox allows the user to enable the camera to send an email when a video tampering
alarm is triggered.
PTZ: This checkbox allows the user to enable the camera to activate a PTZ tour when a video tampering alarm
is triggered.
Snapshot: This checkbox allows the user to enable the camera to take a snapshot when a video tampering
alarm is triggered.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
68
5.4.3.2 Audio Detection
This menu allows the user to modify audio detection settings. Below is a screenshot of the Audio Detect screen:
Below is an explanation of the fields on the Audio Detect tab:
 Enable: This checkbox enables an audio detection alarm for the camera.
 Enable Intensity Change: This checkbox enables intensity change for the camera audio.
o Sensitivity is the amount of change required to increase the audio detected by a percentage. The
lower the sensitivity, the more audio variance is required to trigger an alarm.
o Threshold is the level that the detected audio needs to reach in order to trigger an alarm. The lower
the threshold, the more likely that audio will trigger an alarm.
 Working Period: Clicking this button opens a weekly schedule that can be used to set times.
o

Click and drag to set audio tampering for certain days of the week. Also, periods of audio detection
can be set for each day and enabled using the period settings on the bottom half of the screen. There
are a total of 6 periods that can be set.
Anti-Dither: This field allows the user to set the anti-dither time. The values in this field can range from 5 to
600 seconds. This time value controls how long the alarm signal lasts. Based on audio detection, a buzzer can
go off, a tour can begin, PTZ can be activated, a snapshot can be taken, or the camera can begin recording.
o For example, if the anti-dither time is set to 10 seconds, each alarm may last 10 seconds if the local
alarm is activated. During the process, if the system detects another local alarm signal at the fifth
second, the buzzer, tour, PTZ activation, snapshot, record channel functions will begin another 10
seconds while the screen prompt, alarm upload, email will not be activated again. After 10 seconds, if
system detects another alarm signal, it can generate a new alarm since the anti-dither time has
expired.
69







Record: This checkbox allows the user to enable the camera to record video when an audio detection alarm is
triggered.
Record Delay: his field specifies in seconds how long the delay between alarm activation and recording should
be.
Relay Out: This checkbox allows the user to enable the camera to trigger a connected alarm (connected to the
alarm port on the back of the camera) when an audio detection alarm is triggered.
Alarm Delay: This field specifies in seconds how long the delay between alarm activation and Relay alarm
activation should be.
Send Email: This checkbox allows the user to enable the camera to send an email when an audio detection
alarm is triggered.
PTZ: This checkbox allows the user to enable the camera to activate a PTZ tour when an audio detection alarm
is triggered.
Snapshot: This checkbox allows the user to enable the camera to take a snapshot when an audio detection
alarm is triggered.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
5.4.3.3 Alarm
This screen is used to set external alarm settings for the camera and any devices attached to the camera’s relay.
Below is a screenshot of the Alarm settings screen:
Below is an explanation of the fields on the Alarm settings screen:
 Enable: This checkbox enables external alarm activation for the camera.
 Relay In: This dropdown box allows the user to select which relay input’s settings are modified.
 Working Period: Clicking this button opens a weekly schedule that can be used to set times.
70
o









Click and drag to set alarm activation for certain days of the week. Also, periods of relay activation
can be set for each day and enabled using the period settings on the bottom half of the screen. There
are a total of 6 periods that can be set.
Anti-Dither: This field allows the user to set the anti-dither time. The values in this field can range from 5 to
600 seconds. This time value controls how long the alarm signal lasts. Based on relay activation, a buzzer can
go off, a tour can begin, PTZ can be activated, a snapshot can be taken, or the camera can begin recording.
o For example, if the anti-dither time is set to 10 seconds, each alarm may last 10 seconds if the local
alarm is activated. During the process, if the system detects another local alarm signal at the fifth
second, the buzzer, tour, PTZ activation, snapshot, record channel functions will begin another 10
seconds while the screen prompt, alarm upload, email will not be activated again. After 10 seconds, if
system detects another alarm signal, it can generate a new alarm since the anti-dither time has
expired.
Sensor Type: This dropdown box allows the user to select which sensor type to use. The options are Normally
Open (NO) and Normally Closed (NC).
Record: This checkbox allows the user to enable the camera to record video when an alarm is activated.
Record Delay: This field specifies in seconds how long the delay between alarm activation and recording
should be.
Relay Out: This checkbox allows the user to enable the camera to trigger a connected alarm (connected to the
alarm port on the back of the camera) when a relay activation alarm is triggered.
Alarm Delay: This field specifies in seconds how long the delay between alarm activation and Relay alarm
activation should be.
Send Email: This checkbox allows the user to enable the camera to send an email when an alarm is activated.
PTZ: This checkbox allows the user to enable the camera to activate a PTZ tour when an alarm is activated.
Snapshot: This checkbox allows the user to enable the camera to take a snapshot when an alarm is activated.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
71
5.4.3.4 Abnormality
This menu has 3 tabs: SD Card, Network, and Illegal Access
5.4.3.4.1 SD Card
This tab allows the user to set the camera’s response to an SD card related abnormality. Below is a screenshot of
the SD card tab screen:
Below is an explanation of the fields on the SD Card settings tab:
 Event Type: This dropdown box allows the user to select which SD card abnormality to set event triggers for.
The 3 options are No SD Card, SD Card Error, and Capacity Warning.
 Enable: This checkbox enables the SD Card abnormality trigger for the camera.
 Relay Out: This checkbox allows the user to enable the camera to trigger an alarm when an SD Card
abnormality is detected.
 Alarm Delay: This field specifies in seconds how long the delay between alarm activation and relay alarm
activation should be.
 Send Email: This checkbox allows the user to enable the camera to send an email when an SD Card
abnormality is detected.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
72
5.4.3.4.2 Network
This tab allows the user to set the camera’s response to a Network related abnormality. Below is a screenshot of
the Network tab screen:
Below is an explanation of the fields on the Network settings tab:
 Event Type: This dropdown box allows the user to select which Network abnormality to set event triggers for.
The 2 options are Disconnection and IP Conflict.
 Enable: This checkbox enables the Network abnormality trigger for the camera.
 Record: This checkbox allows the user to enable the camera to record video when a network abnormality is
detected.
 Record Delay: This field specifies in seconds how long the delay between alarm activation and recording
should be.
 Relay Out: This checkbox allows the user to enable the camera to trigger an alarm when a network
abnormality is detected.
 Alarm Delay: This field specifies in seconds how long the delay between alarm activation and relay alarm
activation should be.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
73
5.4.3.4.3 Illegal Access
This tab allows the user to set the camera’s response to an Illegal Access related abnormality. Below is a
screenshot of the Illegal Access tab screen:
Below is an explanation of the fields on the Illegal Access settings tab:
 Enable: This checkbox enables the Illegal Access abnormality trigger for the camera.
 Login Failure: This field allows the user to specify how many failed login attempts must be attempted in order
to trigger an Illegal Access abnormality event.
 Relay Out: This checkbox allows the user to enable the camera to trigger an alarm when illegal access is
detected.
 Alarm Delay: This field specifies in seconds how long the delay between alarm activation and relay alarm
activation should be.
 Send Email: This checkbox allows the user to enable the camera to send an email when illegal access is
attempted.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
74
5.4.4 Storage
This menu section allows the user to change storage settings for the camera.
5.4.4.1 Schedule
The schedule menu manages the recording schedule for the camera. This menu has 3 tabs: Record Schedule,
Snapshot Schedule, and Holiday Schedule.
5.4.4.1.1 Record Schedule
This tab is where video recording settings are configured. Below is a screenshot of the Record Schedule settings
screen:
Below is an explanation of the fields on the Record Schedule settings tab:
 Record Type: These checkboxes allow the user to select which recording type they want to configure on the
schedule. There are 3 types of recordings:
o General: General recording means that the camera captures all footage for the specified time period.
General recording is represented by the color green.
o Motion: Motion Detection recording means that the camera captures only footage when the motion
detection alarm is activated. Motion recording is represented by the color yellow.
o Alarm: Alarm recording means that the camera captures only footage when an alarm is activated.
Alarm recording is represented by the color red.
 Video Recording Schedule: To specify a video recording range, first select the type of recording desired, then
click and drag on time bar for the desired date. To edit multiple days at once, drag the cursor further up or
down to cover the other days.
o Setup: Clicking this button opens a screen that allows for recording periods to be set for each day and
for each recording type. There are a total of 6 periods that can be set.
75
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
5.4.4.1.2 Snapshot Schedule
This tab is where snapshot recording settings are configured. Below is a screenshot of the Snapshot Schedule
settings screen:
Below is an explanation of the fields on the Snapshot Schedule settings tab:
 Record Type: These checkboxes allow the user to select which snapshot type they want to configure on the
schedule. There are 3 types of snapshots:
o General: General means that the camera will take snapshots during the specified time period.
General recording is represented by the color green.
o Motion: Motion Detection means that the camera only takes snapshots when the motion detection
alarm is activated. Motion recording is represented by the color yellow.
o Alarm: Alarm means that the camera only takes snapshots when an alarm is activated. Alarm
recording is represented by the color red.
 Snapshot Recording Schedule: To specify a snapshot range, first select the type of snapshot desired, then click
and drag on time bar for the desired date. To edit multiple days at once, drag the cursor further up or down to
cover the other days.
o Setup: Clicking this button opens a screen that allows for snapshot periods to be set for each day and
for each snapshot type. There are a total of 6 periods that can be set.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
76
5.4.4.1.3 Holiday Schedule
This tab is where holiday settings are configured. Below is a screenshot of the Holiday Schedule settings screen:
Below is an explanation of the fields on the Holiday Schedule settings tab:
 Record Type: These checkboxes allow the user to select which recording type they want to configure on the
schedule. There are 2 types of recordings:
o Record: This checkbox is referring to video recording.
o Snapshot: This checkbox is referring to snapshot recording.
 Calendar: This calendar allows the user to select days to designate as holidays. Once a day is designated, it can
be customized to stop recording or snapshots for that day by using the Record and Snapshot checkboxes.
To refresh the page, click the Refresh button. To save the settings, click the Save button.
77
5.4.4.2 Destination
This menu controls where recorded media is stored. There are 4 tabs in this menu: Path, SD Card, FTP, and NAS.
5.4.4.2.1 Path
This tab is where the user can designate a path for recorded video and snapshots to reside in. Below is a
screenshot of the Path tab:
Below is an explanation of the fields on the Path settings tab:
 Event Type: This column designates storage options available to the camera. The options are SD Card, FTP,
and NAS.
 Record Type: These columns designate which recording type should be recorded to which event type. Check
the box at the intersection of the record type and event type to designate where that recording should be sent
to.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
5.4.4.2.2 SD Card
This tab is where the user can change SD card settings. Below is a screenshot of the SD Card tab:
Below is an explanation of the fields on the SD Card settings tab:
 Device Name: This column designates the name of the SD card that is currently in the camera.
 Status: This column designates the status of the SD card.
 Attribute: This column designates the read/write attributes for the SD card. By default this is Read & Write.
 Used Capacity/Total Capacity: This column shows the available memory on the SC card.
 Read Only: This button allows the user to designate an SD card as read only.
 Hot Swap: This button allows the user to physically remove the SD card and replace it with another safely.
78


Refresh: This button refreshes the SD card table.
Format: This button formats the SD card.
5.4.4.2.3 FTP
This tab is where the user can change FTP settings. Below is a screenshot of the FTP tab:
Below is an explanation of the fields on the FTP settings tab:
 Enable: This checkbox allows the user to enable FTP uploading for the camera’s recorded media.
 Server Address: This field allows the user to designate a DDNS address for the FTP server.
 Port: This field allows the user to designate the port number for the FTP server.
 User Name: This field allows the user to input the username used to login to the FTP server.
 Password: This field allows the user to input the password used to login to the FTP server.
 Remote Directory: This field allows the user to specify a remote directory on the FTP to send the recorded
media to.
 Emergency (Store on SD Card): This checkbox allows the camera to store recorded media on the SD card in
case the FTP server is unavailable.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
79
5.4.4.2.4 NAS
This tab is where the user can change NAS settings. Below is a screenshot of the NAS tab:
Below is an explanation of the fields on the NAS settings tab:
 Enable: This checkbox allows the user to enable NAS uploading for the camera’s recorded media.
 Server Address: This field allows the user to designate a DDNS address for the NAS server/device.
 Remote Directory: This field allows the user to specify a remote directory on the NAS to send the recorded
media to.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
5.4.4.3 Record Control
This menu is where general recording settings are configured. Below is a screenshot of the record control menu:
Below is an explanation of the fields on the Record Control settings tab:
 Pack Duration: This field allows the user to set how many minutes each file is comprised of.
 Pre-event Record: This field allows the user to specify how many seconds before an event should be recorded.
 Disk Full: This dropdown box allows the user to designate what the camera should do when the disk is full.
There are 2 options: Overwrite or Stop.
 Record Mode: This set of radio buttons allows the user to designate the recording mode. The options are
Auto, Manual, and Off.
 Record Stream: This dropdown box allows the user to specify which stream to record. The options are main
stream and sub stream.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
80
5.4.5 System
This menu section allows the user to change general settings for the camera.
5.4.5.1 General
This menu controls where general settings are configured. There are 2 tabs in this menu: General and Date & Time.
5.4.5.1.1 General
This tab is where the user can configure some basic camera settings. Below is a screenshot of the General tab:
Below is an explanation of the fields on the General settings tab:
 Device Name: This field allows the user to change the device’s name.
 Language: This dropdown box allows the user to change the language used in the camera.
 Video Standard: This dropdown box allows the user to select either the NTSC or PAL video standard.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
81
5.4.5.1.1 Date & Time
This tab is where the user can configure the date and time settings for the camera. Below is a screenshot of the
Date & Time tab:
Below is an explanation of the fields on the Date & Time settings tab:












Date Format: This dropdown box allows the user to change the date format used in the camera.
Time Format: This dropdown box allows the user to change the time format used in the camera.
Time Zone: This dropdown box allows the user to change the time zone used in the camera.
Current Time: This field allows the user to enter in the date and time manually. Clicking the PC Sync button
allows the camera to sync with a Network Time Protocol (NTP) server.
Enable DST: This checkbox allows the user to enable daylight savings time for the camera.
DST Type: This radio button allows the user to select whether DST is based on the week, or a specific day.
Start Time: This dropdown box and field allow the user to enter in the start time for DST.
End Time: This dropdown box and field allow the user to enter in the end time for DST.
Synchronize with NTP: This checkbox allows the user to enable the camera’s synchronization with an NTP
server.
NTP Server: This field allows the user to enter in an NTP server.
Port: This field allows the user to enter in the port number for the NTP server.
Update Period: This field allows the user to enter in the update period time. This number designates how
frequently the camera pings the NTP server to ensure it has the correct time. The range is from 0-30 minutes.
To reset to default settings, click the Reset Defaults button. To refresh the page, click the Refresh button. To save
the settings, click the Save button.
82
5.4.5.2 Manage Users
This menu allows the user to change the user accounts on the camera. By default, the camera only has the admin
account which has all rights/authorities. Additional accounts can be created on this screen. Below is a screenshot
of the manage users screen:
Below is an explanation of the fields on the Manage Users screen:
 Anonymous Login: This checkbox allows the user to enable the anonymous login feature. This allows all user
account names to remain hidden on this screen.
 User Name: This tab shows the usernames available on the camera.
 Group: This tab shows the user groups available on the camera.
 No.: This column shows the user’s number on the user list.
 User Name: This column shows the usernames of the different accounts on the camera.
 Group Name: This column shows the group of the different accounts on the camera.
 Description: This column shows a description of the account.
 Modify: This column allows the user to modify the user account.
 Delete: This column allows the user to delete a user account. Note: The admin account cannot be deleted.
 Authority List: This box shows which user rights/authorities are assigned to an account.
 Add User: This button allows the user to add a new user to the camera.
83
5.4.5.3 Restore Factory Settings
This screen allows the user to reset the camera and all of its settings to the factory settings. Below is a screenshot
of the Default screen:
Note: An alternate method to conduct a Factory Reset for the device is to press and hold the indicator light/reset
button on the back of the device for 10 seconds (until the light changes).
5.4.5.4 Import/Export
This screen allows the user to import or export settings from the camera. Below is a screenshot of the
Import/Export screen:
To import settings, click the Import button. To export settings, click the Export button.
84
5.4.5.5 Auto Maintain
This screen allows the user to set auto maintenance settings for the camera. Below is a screenshot of the Auto
Maintain screen:
Below is an explanation of the fields on the Auto Maintain screen:
 Auto Reboot: This checkbox allows the user to enable the auto reboot function. The dropdown box and field
to the right of this checkbox allow the user to specify what date and time of the week the camera will auto
reboot.
 Auto Delete Old Files: This checkbox allows the user to enable the auto deletion of old files on the camera.
 Manual Reboot: This button allows the user to manually reboot the camera.
To refresh the page, click the Refresh button. To save the settings, click the Save button.
5.4.5.6 Upgrade
This menu allows the user to upgrade the camera’s firmware. Below is a screenshot of the Upgrade screen:
To search the PC for a firmware file, click the Browse button. To upgrade once the firmware file is selected, click
Upgrade.
Note: When upgrading the camera’s firmware, do not disconnect the internet or power from the camera.
85
5.4.6 Information
This menu section allows the user to view information about the camera for reference purposes.
5.4.6.1 Version
This screen allows the user to see various information about the camera’s software versions, as well as other
information. Below is a screenshot of the camera’s version screen:
On this screen, software version, web interface version, and ONVIF version are displayed. Also, the S/N (Token ID)
is displayed here.
5.4.6.2 Log
This screen is where the camera’s activity log is kept. Below is a screenshot of the Log screen:
To view logs for a specific time period, modify the start time and end time fields, choose the type of event (system,
setting, data, event, record, manage users, clear log), and click search.
To backup the log, click the Backup button. To clear the log, click the Clear button.
86
5.4.6.3 Online Users
This screen allows the user to see which users are online. Below is a screenshot of the Online Users screen:
Click Refresh to refresh this table.
5.5 Alarm
This screen is where the alarm log is kept. Below is a screenshot of the alarm screen:
The table on the right shows the alarm log and all of the alarm instances that have occurred.
The checkboxes allow the user to narrow down which alarms they want to see in the alarm log. Clicking the
checkbox next to Prompt will cause the system to pop up a dialog box anytime an alarm is triggered. Clicking the
checkbox next to Play Custom Alarm will use a custom alarm sound for the alarm prompt. Click the Browse button
to search for a custom alarm sound to use.
5.6 Logout
Clicking the logout button will log out the user.
87
6. FAQs/Troubleshooting
1.
The camera does not boot up properly.
Below are a few possible reasons why this may be occurring:



The power input is not correct voltage.
The power cable connection is not secured correctly.
The firmware was upgraded incorrectly.
2.
Camera often automatically shuts down or stops running.
Below are a few possible reasons why this may be occurring:




The input voltage is too low or is not stable.
The insides of the camera have accumulated too much dust.
The temperature is either too hot or too cold.
The hardware is malfunctioning.
3.
The system does not detect an SD Card.
Below are a few possible reasons why this may be occurring:



The SD card is broken.
The SD card slot is malfunctioning.
The SD card has not been formatted properly.
4. Real-time video color is distorted.
Below are a few possible reasons why this may be occurring:


The camera is not compatible with the monitor.
The camera color or brightness settings are not correctly configured.
5. Local Recordings are not searchable.
Below are a few possible reasons why this may be occurring:





The SD card is broken.
The SD card slot is malfunctioning.
The camera’s firmware is incompatible with the recorded video.
The recorded files have been overwritten.
The recording function has been disabled.
6. Playback video is distorted.
88
Below are a few possible reasons why this may be occurring:





The video quality setting is too low.
The camera software has a read error. Restart the camera to solve this problem.
The SD card is broken.
The SD card slot is malfunctioning.
The camera’s hardware is malfunctioning.
7. There is no audio during real-time monitoring.
Below are a few possible reasons why this may be occurring:



The camera’s microphone is damaged.
The speakers being used are not sufficiently powered.
The camera hardware is malfunctioning.
8. There is no audio during recorded video playback.
Below are a few possible reasons why this may be occurring:


Audio recording may not be enabled.
The camera’s microphone is damaged.
9. The timestamp is not displaying the correct time.
Below are a few possible reasons why this may be occurring:

The time and date settings may not be configured correctly.
10. Motion detection does not work.
Below are a few possible reasons why this may be occurring:



The motion detection time period may be incorrectly configured.
Motion detection zone setup is not correctly configured.
Motion detection sensitivity is too low.
89
11. Web Access isn't working.
Below are a few possible reasons why this may be occurring:






Windows version is pre -Windows 2000 service pack 4. Use a more recent version of Windows.
ActiveX controls have been disabled.
The PC is not using DirectX 8.1 or higher. Upgrade to a more recent version of DirectX.
The camera is having network connection errors.
Web access may be setup incorrectly.
The username or password may be incorrect.
12. Web Access live view is only displaying a static picture. Both live playback and recorded playback aren't
working.
Below are a few possible reasons why this may be occurring:






The network speed is not sufficient to transfer video data via web access.
The client PC may have limited resources.
Multicast mode may be causing this issue.
A privacy mask or screensaver may be enabled.
The logged in user may not have sufficient rights to monitor real-time playback.
The camera’s local video output quality is not sufficient.
13. Network connection is not stable.
Below are a few possible reasons why this may be occurring:





The network is not stable.
There may be an IP address conflict.
There may be a MAC address conflict.
The PC or camera network card may be defective.
The PoE cable is too long.
14. The alarm signal cannot been disarmed.
Below are a few possible reasons why this may be occurring:



An alarm may be setup incorrectly.
An alarm output may have been manually opened.
There may be an error in the camera’s firmware.
90
15. Alarms are not working.
Below are a few possible reasons why this may be occurring:




The alarm is not setup correctly.
The alarm cable is not connected correctly.
The alarm input signal is not correctly configured.
There are two loops connected to one alarm device.
16. The camera is not recording enough video.
Below are a few possible reasons why this may be occurring:


The storage capacity is not enough.
The storage device is damaged.
17. Downloaded files cannot be played back.
Below are a few possible reasons why this may be occurring:



The media player software on the PC may not be able to read the file format.
The PC may not have DirectX 8.1 or higher.
The PC may not have Windows XP or higher.
18. Forgot login information.
Below are a few solutions:

Hold the reset button on the back of the camera to execute a factory reset. This will restore the device to its
factory settings and will reset ALL of the camera’s settings.
19. When I login via HTTPS, a dialogue says the certificate has expired or is not valid yet.
Ensure the PC has the same time as the camera’s system time.
91
Glossary of Terms






















Abnormality – Any malfunction in terms of storage of data to the SD card.
Alarm Delay – The gap in time between alarm activation and Relay alarm activation.
Alternate Gateway – The node on the computer network that the network software uses when an IP address
does not match any other routes in the routing table, and when the default gateway is not available.
Anti-Dither – This time value controls how long the alarm signal lasts. The values in this field can range from 5
to 600 seconds. Based on motion detection, a buzzer can go off, a tour can begin, PTZ can be activated, a
snapshot can be taken, or the camera can begin recording.
DDNS – This stands for Dynamic Domain Name System. DDNS is a method of automatically updating a name
server in the Domain Name System (DNS), often in real time, with the active DNS configuration of its
configured hostnames, addresses or other information.
Default Gateway – The node on the computer network that the network software uses when an IP address
does not match any other routes in the routing table.
DHCP – Dynamic Host Configuration Protocol is a network protocol that enables a server to automatically
assign an IP address to a computer from a defined range of numbers (i.e., a scope) configured for a given
network.
Fluency – Fluency described the lack of stuttering or excessive delay in a video stream. Fluency usually comes
at the expense of video quality when a network is constrained.
IP Address – Internet Protocol Address is a unique numerical label assigned to each device connected to a
computer network. The IP address allows communication between different devices on a network.
Main Stream – Main Stream is the main streaming protocol for the camera. Main stream uses more
bandwidth and attempts to keep quality and fluency high.
NO/NC – Normally Open and Normally Closed are options for sensor type. These settings allow for different
exposure types when capturing video and still images.
NTP – Network Time Protocol is a networking protocol for clock synchronization between computer systems
over packet-switched, variable-latency data networks.
P2P – Peer-to-Peer is a decentralized communications model in which each party has the same capabilities
and either party can initiate a communication session.
PPPoE – Point to Point Protocol over Ethernet is a network protocol for encapsulating Point to Point Protocol
data packets inside Ethernet frames.
PTZ – Pan Tilt Zoom is a feature that allows a camera to remotely change its position.
QR Code – Quick Response code is a type of digital barcode that enables devices to share complex data strings
quickly.
Record Delay – Record Delay specifies in seconds how long the delay between alarm activation and recording
should be.
Relay Out – Relay Out triggers a connected alarm (connected to the alarm port on the back of the camera)
when an alarm on the camera is triggered.
S/N – S/N stands for serial number. The S/N is unique to each camera and can be used to connect to different
Amcrest apps and services to provide different methods of access to the camera.
Sensitivity – Sensitivity is the amount of change required to increase the motion detected by a percentage.
The lower the sensitivity, the more movement is required to trigger an alarm.
SMTP – Simple Main Transfer Protocol is an Internet standard for electronic mail (e-mail) transmission.
Static IP – An IP address that does not change.
92






Sub Stream – Sub Stream is an alternative streaming protocol for the camera. Sub stream uses less bandwidth
and attempts to keep fluency high at the expense of quality.
Subnet Mask – a 32-bit number that masks an IP address, and divides the IP address into network address and
host address.
TCP/IP – TCP/IP stands for Transmission Control Protocol/Internet Protocol and it is the language/protocol
that allows communication between internet connected devices, whether on a local network, or a on the
Internet at large.
Threshold – Threshold is the level that the motion detection needs to reach in order to trigger an alarm.
UPnP – UPnP stands for Universal Plug and Play, and it is a protocol used to easily connect devices to the
internet.
Video Tamper – Video Tamper refers to any major changes happening to the video feed such as it being
blocked out, interfered with, or disconnected.
93
FCC Statement
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
2. The users manual or instruction manual for an intentional or unintentional radiator shall caution the user
that changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment. In cases where the manual is provided only in a form other than paper, such
as on a computer disk or over the Internet, the information required by this section may be included in the manual
in that alternative form, provided the user can reasonably be expected to have the capability to access information
in that form.
3. (b) For a Class B digital device or peripheral, the instructions furnished the user shall include the following
or similar statement, placed in a prominent location in the text of the manual:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
4. RF exposure warning
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used
for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must
not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must
be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure
compliance.
94
Appendix A: Toxic or Hazardous Materials or Elements
Toxic or Hazardous Materials or Elements
Component
Name
Pb
Hg
Cd
Cr VI
PBB
PBDE
○
○
○
○
○
○
（Panel）
○
○
○
○
○
○
Circuit Board
○
○
○
○
○
○
Fastener
○
○
○
○
○
○
Wire and
Cable/Ac
Adapter
○
○
○
○
○
○
Packing
Material
○
○
○
○
○
○
Accessories
○
○
○
○
○
○
Sheet
Metal(Case)
Plastic Parts
O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below
the relevant threshold of the SJ/T11363-2006 standard.
X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the
parts is above the relevant threshold of the SJ/T11363-2006 standard. During the environmental-friendly use
period (EFUP) period, the toxic or hazardous substance or elements contained in products will not leak or mutate
so that the use of these (substances or elements) will not result in any severe environmental pollution, any bodily
injury or damage to any assets. The consumer is not authorized to process such kind of substances or elements,
please return to the corresponding local authorities to process according to your local government statutes.
95
Note:





For detailed operational instructions, please refer to the User Manual on the CD that was included in
your purchase.
To view setup videos for many of the steps outlined in this guide, go to http://amcrest.com/videos
This user manual is for reference only. Slight differences may be found in the user interface.
All the designs and software here are subject to change without prior written notice.
All trademarks and registered trademarks mentioned are the properties of their respective owners.
To contact Amcrest support, please do one of the following:



Visit http://amcrest.com/contacts and use the email form
Call Amcrest Support using one of the following numbers
Toll Free US: (888) 212-7538
International Callers (Outside of US): +1-713-893-8956
USA: 713-893-8956
Canada: 437-888-0177
UK: 203-769-2757
Email Amcrest Customer Support [email protected]
Copyright Amcrest© 2016
96
">