advertisement
SpeedCheck
®
APPLIED INFORMATION (AI) INTEGRATION INSTALL GUIDE
For the SPEEDCHECK-12
SPEEDCHECK-12
(Battery/Solar)
SPEEDCHECK-12
(AC)
90063_INSTALL-GUIDE_SPEEDCHECK-12-AI-Integration-Kit_RevC
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected]
| carmanah.com
APPLIED INFORMATION (AI) INTEGRATION
INSTALL GUIDE
Table of Contents
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected]
| carmanah.com
2
1.0 Warnings and Precautions
APPLIED INFORMATION (AI) INTEGRATION
INSTALL GUIDE
The following symbols indicate important safety warnings and precautions throughout this guide:
WARNING indicates that serious bodily harm or death may result from failure to adhere to the precautions.
CAUTION indicates that damage to equipment may result if the instructions are not followed.
NOTE suggests optimal conditions and provides additional information.
1.1 Warranty Disclaimer
This manual will familiarize you with the features, operation standards and installation of Carmana h’s
SPEEDCHECK-12 Applied Information (AI) Integration Kit. Failure to comply with the use, storage, maintenance, installation or placement instructions detailed in this manual could void the warranty.
1.2 Standards
Perform all installation, wiring, grounding and maintenance in conformance with local building and electrical codes. Adherence to the National Electrical Code (NEC) is mandatory to comply with any certification markings.
Non-adherence to code may void the warranty.
1.3 Safety and Usage Precautions
Batteries are shipped fully charged. Use extreme caution when handling the batteries as they can generate hazardous short-circuit currents. Remove all jewelry (bracelets, metal-strap watches, etc.) before handling the batteries.
Solar panels produce DC electricity when exposed to light and can therefore produce an electrical shock or burn. To render solar panels inoperative, remove them from sunlight or fully cover their front surface with an opaque material.
Before lifting any heavy or bulky equipment, ensure the load is secured so moving parts do not shift, and that it can be lifted as far as needed without back strain or loss of grip. Installation may require more than one person.
Ensure the equipment is not powered during installation and wiring of the system.
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected]
| carmanah.com
3
APPLIED INFORMATION (AI) INTEGRATION
INSTALL GUIDE
Recheck all completed wiring for proper polarity prior to energizing the system.
Changes or modifications to Carmanah equipment not expressly approved by Carmanah could void both the user's authority to operate the equipment and the warranty.
Product can have sharp edges. Accidental movement of hinged components can cause injury.
This guide is specific to the SPEEDCHECK-12 AI Integration Kit installation and is not a replacement for the complete SPEEDCHECK-12 product user manual.
Visit support.carmanah.com
to download the complete product user manual.
1.4 Applications
For Carmanah SPEEDCHECK-12 radar speed signs, the AI Integration Kit allows for remote system monitoring, scheduling and control.
The SPEEDCHECK-12 AI Integration Kit is available in two different states of assembly described below:
•
If ordered with a SPEEDCHECK-12 system : the display enclosure harnessing is assembled in the factory, creating an “AI-ready” SPEEDCHECK-12 system. The AI Integration Kit comes as parts to be installed by the user following all installation steps provided.
•
If ordered separately : the SPEEDCHECK-12 display enclosure must be replaced prior to following these installation steps. See the note below.
If installing into an existing system that was not ordered with the AI Integration Kit, you will require a new display enclosure. Contact Carmanah for more information.
For systems that have the optional large external SpeedCheck cabinet the door switch sensor is not compatible with SPEEDCHECK-12.
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected]
| carmanah.com
4
APPLIED INFORMATION (AI) INTEGRATION
INSTALL GUIDE
2.0 System Components
The SPEEDCHECK-12 Applied Information (AI) Integration Kit consists of the following items:
1. Mount plate, AI FCU (1)
2. Harness, AI FCU to bulkhead (1)
3. Harness, solar monitoring, 8' (1)
4. Nut, nyloc, 1/4"-20 (4)
5. Cable tie, 4-way, mounting base (2)
6. Cable tie, 4" (4)
7. Cable tie, 7", #8 screw mount (1)
8. Screw, #8-32 x 1/4", pan head (3)
9. Screw, #8-32 x 3/8", pan head (1)
10. Adapter, 90°, SMA male to SMA female (2)
11. Adapter, harness, AI 070B to 030/070C (1)
The Applied Information AI-500-070B and AI-500-030 (monitoring only) are supported with
SPEEDCHECK-12 systems. Modem supplied separately.
3.0 Tools and Materials Required
The following tools and materials may be required to install the AI Integration Kit into your SPEEDCHECK-12 system:
1. Drill and 17/32" drill bit
2. Deburring tool or similar
3. Crescent wrench
4. Side cutters
5. Multi-bit screwdriver
6. Socket set
7. 18/19mm wrench or 3/4" fuel inject socket
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected]
| carmanah.com
5
APPLIED INFORMATION (AI) INTEGRATION
INSTALL GUIDE
4.0 Installation
4.1 Opening Rear Enclosure
1. To open SPEEDCHECK-12, insert included key into lock and rotate clockwise.
2. Apply diagonal pressure to the bottom right corner of the sign face then PULL on the key.
3. Once unlocked, the key can be removed.
4. Swing the display enclosure away from the rear enclosure.
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected]
| carmanah.com
6
4.2 AI-500-070B Field Control Unit (FCU)
APPLIED INFORMATION (AI) INTEGRATION
INSTALL GUIDE
If a second battery is installed in the upper part of the rear enclosure it will need to be removed to fit the AI-500-070B Field Control Unit (FCU). Remove the upper battery, battery bracket and battery shelf prior to installing the FCU mounting plate.
1. Disconnect power to the system by opening all battery fuse holders or switch off the breaker (to the right).
2. Install the AI-500-070B mounting plate into the rear enclosure and secure with three nyloc nuts in the locations outlined below.
3. Drill a 17/32" hole in the top corner of the rear enclosure at the half shear location. Deburr both sides of the hole and remove all metal chips.
4. Remove jam nut and washers from antenna. Install coax cables through previously drilled hole. Install plastic washer, lock washer and nut as shown below. Ensure the antenna is flush with the rear enclosure and tighten nut with a 19mm wrench.
5. Install two cable tie holders onto the mounting plate as shown below.
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected]
| carmanah.com
7
APPLIED INFORMATION (AI) INTEGRATION
INSTALL GUIDE
6. Route coax cables from antenna to cable tie mounts and loop cables around 2-1/4 turns clockwise.
Secure with four cables ties.
Coax cable connectors should end up approximately in the left of the rear enclosure.
7. Install 16-pin and 4-pin harnesses into the AI-500-070B.
8. Thread two 90° coax adapters onto antenna connectors. Orient as shown below.
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected]
| carmanah.com
8
APPLIED INFORMATION (AI) INTEGRATION
INSTALL GUIDE
9. Install AI-500-070B onto mounting plate with three #8-32x1/4" screws.
10. Install screw mount cable tie around harness wires end secure to lower-left mounting plate standoff with one #8-32x3/8" screw.
11. Install harness ground ring terminal onto stud shown and fasten with one nyloc nut. Orient as shown.
12. Thread GPS and LTE antenna coax harness connectors onto correct connectors on the AI-500-070B (not shown below).
Cell – Front
GPS – Rear
Yellow sensor wire will remain unterminated for AC-powered systems. For solar-powered
systems this will mate with the yellow wire from the solar kit. See Section 4.3
information.
13. Connect the 2-pin and 4-pin AI-500-070B connectors to the open receptacles on the display enclosure as shown below. All 2-pin connectors are interchangeable.
Battery Only or AC w/ AI FCU Solar Kit w/ Battery & AI FCU
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected]
| carmanah.com
9
APPLIED INFORMATION (AI) INTEGRATION
INSTALL GUIDE
4.3 Solar Version Only
1. For solar kit versions, there is a length of yellow sensor wire to be routed with the battery harness from the solar kit to the LED display.
2. Terminate this yellow sensor wire to the Solar positive (+) terminal of the charge controller. Route the sensor wire down the pole and into the rear enclosure.
3. Once the sensor wire is inside the rear enclosure, connect it to the yellow wire shown below.
To AI FCU harness solar sensor wire
To charge controller
Solar +
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected]
| carmanah.com
10
APPLIED INFORMATION (AI) INTEGRATION
INSTALL GUIDE
4.4 Testing AI-500-070B
1. Ensure AI serial number has been activated.
2. Set toggle switch to “OFF”.
3. Ensure connectors are properly mated on the bottom of the AI-500-070B.
4. Confirm correct wiring and power-up system by connecting the DC power (battery fuses or switch on the breaker) and turning on the AI power switch.
5. Open your PC, open a browser and navigate to the Glance website: glance.appinfoinc.com
6. Log in using the credentials provided by AI or the distributor you purchased the equipment from.
7. On the upper-left side of the browser, select the device name that matches the Device ID (the ID number labelled on the AI-500-070B).
Ensure the equipment is not powering during installation. Recheck all wiring prior to energizing the system.
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected]
| carmanah.com
11
APPLIED INFORMATION (AI) INTEGRATION
INSTALL GUIDE
8. Ensure that the “Current Status” indicates “Online”.
9. Ensure “Current Device Status” is “OK”.
10. Contact Applied Information to arrange the firmware in the AI unit to be programmed correctly, if this hasn’t already been done. a. Phone: 678.830.2170 b. Email: [email protected]
c. Web: appinfoinc.com
11. To close, push the display enclosure against the rear enclosure and then apply diagonal pressure in the bottom right corner of the sign face. Once fully closed then PUSH the lock to secure in place.
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected]
| carmanah.com
12
APPLIED INFORMATION (AI) INTEGRATION
INSTALL GUIDE
5.0 Appendix A – AI-500-030 Low Power Monitor (LPM)
For systems that will contain the AI-500-030 Low Power Monitor, Carmanah includes an adapter harness to go from the AI-500-070B harness to the AI-500-030 device.
The supplied AI-500-070B (16-pin) harness will connect to the adapter harness (16-pin to 18-pin). The 18-pin end of the adapter harness then connects to the AI-500-030.
The following monitoring parameters will be available with this harness and adapter configuration in a
SPEEDCHECK-12:
•
Solar panel voltage monitoring (solar systems only)
•
System voltage monitoring (AC systems only)
•
Battery voltage monitoring (solar systems only)
•
Knockdown monitoring
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected]
| carmanah.com
13
APPLIED INFORMATION (AI) INTEGRATION
INSTALL GUIDE
1. Follow the instructions provided by Applied Information for installing the AI-500-030 or contact their email support at [email protected]
.
Yellow sensor wire will remain unterminated for AC-powered systems. For solar-powered
systems this will mate with the yellow wire from the solar kit. See Section 4.3
information.
To AI FCU harness solar sensor wire
To charge controller
Solar +
2. Connect the 2-pin and 4-pin AI-500-070B connectors to the open receptacles on the display enclosure as shown below. All 2-pin connectors are interchangeable.
Battery Only or AC w/ AI FCU Solar Kit w/ Battery & AI FCU
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected]
| carmanah.com
14
APPLIED INFORMATION (AI) INTEGRATION
INSTALL GUIDE
1. To adapter harness; #7
2. Not supported by AI-500-030 (leave disconnected)
3. To SPEEDCHECK-12 chassis stud
4. To included solar sensor wire; other end of solar sensor wire to SunSaver Solar +
5. To SPEEDCHECK-12; any 2-pin receptacle
6. To SPEEDCHECK-12; 4-pin receptacle
7. To AI-500-070B harness; #1
8. To AI-500-030 device
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected]
| carmanah.com
15
APPLIED INFORMATION (AI) INTEGRATION
INSTALL GUIDE
© 2022 Carmanah Technologies Corporation
Technical Support:
Email: [email protected]
Toll Free: 1.877.722.8877 (US & Canada)
Worldwide: 1.250.380.0052
Fax:
Web:
1.250.380.0062 carmanah.com
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected]
| carmanah.com
16
advertisement
Key Features
- Displays the speed of approaching vehicles
- Alerts drivers to their speed and encourages them to slow down
- Highly visible and easy to read, even at a distance
- Weather-resistant and can be used in a variety of outdoor environments
- Solar-powered and can be used in remote locations
Related manuals
Frequently Answers and Questions
What is the purpose of the SPEEDCHECK-12?
How does the SPEEDCHECK-12 work?
Where can the SPEEDCHECK-12 be used?
advertisement