Engine stop lever
Forward/reverse lever
Throttle lever
Locking Clutch
lever
clip
Wheel speed lever
Cutter
drive lever
OPERATING
Fuel tap
INSTRUCTIONS
Choke lever
&
SAFETY NOTES
Grease nipple (remove rubber bung)
Grease nipple
Height adjustment skids
BCS
CRUSADER
POWER SCYTHES
BCS615L/620/630
VIBRATION & SOUND LEVELS
Machine
Cutter Bar RPM
Sound
Vibration
m/sec2 - 3 Axis Level dB(A)
BCS 615L Power Scythe 40” (100cm)
2000
8.0
88.0
BCS 620 Power Scythe
40” (100cm)
2000
8.0
88.0
BCS 620 Power Scythe
44” (115cm)
2000
9.3
88.0
BCS 630 Power Scythe
40” (100cm)
2000
6.8
91.0
BCS 630 Power Scythe
44” (115cm)
2000
7.1
91.0
IMPORTANT
WEAR EAR
PROTECTION
READ CAREFULLY
WEAR EYE
PROTECTION
WEAR SAFETY
FOOTWEAR
Tracmaster Ltd, Teknol House, Victoria Road, Burgess Hill RH15 9LH
Tel: 01444 247689 Fax: 01444 871612
Website: www.tracmaster.co.uk E-mail: [email protected]
© Tracmaster Ltd 2008.
Specifications are subject to change without prior notice.
OP/PS/615L-630/0208
No liability will be accepted for any damage
caused to persons or property through failure
to observe the operating and safety instructions.
OPERATION
SAFETY
ALWAYS start the engine in the open air
Use handlebar adjuster to set handlebar height.
DO NOT smoke when refuelling
Pull up clutch lever (located on left handlebar). This will automatically
release stop lever locking clip.
DO NOT mix OIL with the fuel
Ensure the red forward/reverse lever is in the forward position.
ALWAYS stop the engine before making any adjustments,
refuelling, moving or cleaning, or when the unit is
unattended
Engage the cutter bar by using the cutter bar drive lever.
USE ONLY unleaded petrol from fuel containers designed for
this purpose - refuel outdoors only and replace the tank cap
securely
Raise the throttle slightly, release the clutch lever gently and fully,
keeping the red engine stop lever depressed as engine will stop if
released.
IN CASE of petrol spillage move the machines away from the
area of spillage and allow the petrol vapours to dissipate
before starting the engine
Commence work.
DO NOT remove any safety guards that are fitted
DO NOT touch any moving parts or attempt any maintenance
whilst the machine is running - KEEP HANDS AND FEET
AWAY
BEFORE starting work clear the work area of any objects that
could damage the machine
DO NOT allow children or anyone uninstructed to operate the
machine - KEEP ANIMALS AWAY
DO NOT use on slopes or banks of more than 20
Select 1st gear by using the wheel speed lever.
NEVER USE MORE THAN ¼
THROTTLE WHEN THE BAR
IS OPERATING
TO STOP ENGINE
o
ALWAYS wear suitable clothing to give personal protection
including footwear that offers a good grip
AVOID wearing loose garments that may catch in moving parts
Close the throttle.
Pull up the clutch lever.
Locate the wheel speed lever in neutral position.
KNOW how to stop the machine in an emergency
Disengage drive to the cutter bar.
NEVER interfere with any control settings on the engine
Release clutch lever.
NEVER select reverse gear with your back to a wall or other
immovable object
Release engine stop lever completely.
IF A FAULT develops DO NOT attempt any repair - immediately
contact the supplier from whom the machine was obtained
VISUALLY INSPECT the machine before use - ensure all teeth,
nuts and bolts are tight and not worn or damaged and
replace teeth if necessary
KEEP IN MIND the operator is responsible for accidents or
hazards occurring to people or property
TO START ENGINE
Check the engine oil level. Top up with 10w/40 oil if necessary.
Check fuel level. Only use unleaded petrol from a clean container.
Never re-fuel when the engine is hot or running. Leave 1” air space in
the fuel tank.
Depress the engine stop lever (the red lever on the left handlebar)
then pull up the clutch lever and secure with locking clip.
WARNING: THE EXHAUST COVER MAY BE HOT - DO NOT
TOUCH
OPERATING HINTS
Best results are obtained with the engine at a low throttle setting,
which enables the bar to cut cleanly and gives less wear and tear on
the reciprocating parts, which in turn reduces maintenance.
NB: If you are working on a slope, always work across the slope never up or down.
On rough terrain, the bar should be raised by the height adjuster skids
to prevent the blades from digging into the ground.
Always wear gloves.
WARNING: If any abnormal vibrations or sounds occur, STOP the
engine immediately and check the machine and the cutter bar. If you
have any concerns contact your supplier.
MAINTENANCE GUIDE
Ensure the wheel speed lever is in neutral ‘O’ position.
Apply half throttle (the lever on the right handlebar).
Turn the fuel tap to ‘ON’ position, if the engine is cold set the choke
lever to ‘ON’ position.
Pull the recoil start handle gently until it engages then give it a good
strong pull to start the engine.
When the engine has started, release the choke lever after a few
seconds and return the throttle lever to idle position.
For engine maintenance please refer to engine manufacturers
manual.
After every hour of operation stop the engine and remove the spark
plug cap. Check engine oil level (recommended oil SAE 10w/40).
Wash down and re-oil the sliding parts after each day of use.
Lubricate grease nipples every day (where fitted).
Use an old paintbrush to smear grease over the cutter blades.
Replace the spark plug cap.
Do not turn the machine on its side for cleaning.
When the machine is not in use always leave the clutch lever pulled in
and secured with locking clip.
">
