ZyAura ZG906CMONP Operating Instructions

Handheld Multi Gas Detector Operating Instructions
Model: ZG906CMONP
Product Overview
Thank you for selecting ZG906CMONP handheld multi gas detector. The ZG906CMONP is designed to
simultaneously measure multiple gas concentrations in the ambient environment. With long-term data storage,
the user can assess the environmental friendliness. When ZG906CMONP measures the gas concentration
reaching the alarm setting or higher, the data display and alarm functions are activated. ZG906CMONP is
equipped with an RS485 interface for connecting to a computer for remote monitoring so as to reduce the risk
of exposure to high concentrations of harmful gases and avoid harm to human health. ZG906CMONP can be
used in a wide range of industries, which include paint-related industries, wineries, related industries of CO2,
food industry, laboratory, construction industry, etc.
Features:
□
V刈
Dual beam NDIR (Non-Dispersive-Infrared) technology is used to measure CO2 concentration and
improve the long term stability.
□
V Measurement items:
A
E
A
A
E
A
@
A
A
A
A
A
A
E
A
E
A
E
A
E
A
E
A
O2 concentration (%)
氖
NH3 concentration ppm (parts per million)
氖
Battery capacity
此
Atmospheric pressure
此
setting sequence is: yearàmonthàdateàhouràminute. After finishing the real-time setting, press the “M1”
key ( 此
F ) to continue the alarm setting.
A
Time weighted average (8 hours)
Optional: O2, NH3
□
V Large LCD for easy reading of gas concentration and temperature and humidity.
□
V刈
Audible alarm
□
V刈
Data logging with SD card
□
V Through the RS485 interface connection, multiple ZG906CMONP units can be connected to the back-end
computer system as a security monitoring application.刈
□
V Built in the LCD backlight for easy reading in the dark.刈
□
V This device is supplied with Li- ion 18650 3.7V rechargeable batteries, can be used for a long time.
E
氖
E
A
Alarm settings:
The setting order of the sensors is CO2àCOàO2àHN3àPM2.5. Press the "Enter" key ( 此
I ) to switch the
high/low gas concentration alarm setting. Press “▲( 此
G )/▼( 此
J )” key to edit the parameters, and then press
the “M1” key ( 此
F ) to proceed the next sensor alarm value settings. After settings, press and hold the “M1” key
(此
F ) to return to the main screen.
A
A
Basic: CO2, CO, PM2.5, PM10, RH, DP, AMB, Barometer
A
PM10 dust concentration (µg/m3)
此
Short＃Term Exposure Limit
(15 min. weighted average)
此
Maximum value
此
Minimum value
此
Ambient temperature
此
Relative humidity
此
A
A
Dew point
此
Real-time setting display
此
Year display
此
High/low gas concentration calibration
此
High/low gas concentration alarm
此
Display cycle
此
SD card
此
E
E
B. Humidity Sensor
C. Temperature Sensor
D. LCD
E. Charge Lamp
F. M1 (Zone 1 Mode Key)
G. UP\TWA\STEL\Max\Min
H. M2 (Zone 2 Mode Key)
I. Enter
J. DOWN\ALTI
K. Log (Data Logger)
L. USB Socket
M. SD Card Slot
N. RS485 Jack
O. Battery Cover
P. Stand
Q. Screw Position
R. Tripod Screw
E
A
A
E
A
A
E
A
A
E
A
A
E
A
A
E
A
A
Sensor
1
2
3
4
CO2
CO
O2
NH3
PM2.5
PM10
Warm-up time
Data logging interval time setting
5 minutes
After powering on and standby time,
data logging can be operated.
After power on 5 minutes
After power on 5 minutes
After power on 5 minutes
After power on 5 minutes
Data logging interval
time setting
2 seconds~60 minutes
2 seconds~60 minutes
2 seconds~60 minutes
2 seconds~60 minutes
自1 minute
After power on 5 minutes
2 seconds~60 minutes
自1 minute
5 minutes
自1 minute
Data logging:
Press the “Log” key ( 此
K ) for 3 seconds and the screen displays
A
E
to start the data logging function. If
A
long press the “Log” key ( 此
K ),this function can be canceled. When
broken or full; when
E
E
flashes, it means that the SD card is
A
remains stationary, it indicates normal operation.
A
E
A
A
A
H ) for more than 3 seconds and the screen displays
. Zone 2 displays readings
Press the “M2” key ( 此
of all sensors sequentially in time intervals. If you need to increase the display interval time, long press the
“M2” key ( 此
H ).The interval time will automatically increase (1+0.5+0.5….. max. 10 seconds) , and release
the “M2” key ( 此
H ), the readings will be displayed according to the last set interval. If press the “M2” key ( 此
H )
A
E
E
PM2.5 dust concentration (µg/m
此
A
A
E
A
A
again for more than 3 seconds, the
E
A
function can be cancelled.
°C/°F switch:
When the temperature is displayed on the screen, press the "▲" key ( 此
G ) to switch °C/°F.
A
E
A
Atmospheric pressure display:
J ), and then press "▲" key ( 此
G ) to select Altitude (M) à Altitude (ft) à Barometer
Press "▼" key ( 此
(mmHg). The display returns to the main screen after 10 seconds.
A
此
A
A
此
CO concentration, parts per million (ppm)
E
E
Display all sensor readings
A
Basic此刈
Optional氖
Data logging interval time setting:
The default interval time is 00:02 (2 seconds). Press the “Log” key ( 此
K ) for more than 3 seconds and then
the interval time will automatically increase. The interval time, loop display, ranges from 00:02 seconds to
60:00 minutes and then back to 00:02 seconds. The interval time
ff舌尤
switch
刈
仙他
仞
出
is凹
以
冬
及
刈
凹
仕
以
刈
乍
出
包
controlled by the “Enter” key ( 此
I ); the interval time is
舛尤
刈
仙他
仞
出
凹
以
冬
及
刈
凹
仕
以
刈
乍
出
包
包
以
冊
刈
他
冬
刈
充
付
付
壬
A
A
Backlight:
The backlight appears on the screen during startup and operation. After the device is idle for 30 seconds, the
backlight is automatically turned off to extend battery life.
A
3)
A
A
No.
5
E
CO2 concentration, parts per million (ppm)
E
A
Sensor warm-up time and logging Interval:
Measurement:
After power on, the device starts to measure and update the data every second.
F ) to switch the Zone 1 sensor display. (CO2àCOàO2àAMB)
Press the “M1” key ( 此
H ) o switch the Zone 2 sensor display.
Press the “M2” key ( 此
(CO2àCOàO2àNH3àRHàDPàAMBàPM2.5àPM10)
A
Description
E
Operation Instructions
A
Zone 1 sensor selection (CO2, CO, O2, AMB)
Zone 2 sensor selection (CO2, CO, O2, NH3, RH, DP, AMB, PM2.5, PM10)
TWA (CO2, 8-hr time weighted average), STEL (CO2, 15 min. weighted average), MAX, MIN
ALTI (Atmospheric pressure)
Execute a command or select options.
Data logger
LCD display symbol description:
Symbol
A
Power on:
Switch the Power Key ( 此
A ) on.
A. Power Key
Key description:
F )
M1 ( 此
H )
M2 ( 此
日)
汝 (此
木)
汍 (此
I )
Enter ( 此
K )
Log ( 此
A
A
A
(Display Features and Modes)
E
Real-time setting:
Long press the “M1” key ( 此
F ) to proceed the date and time setting. The default format is 24-hour. Press the
“▲( 此
G )/▼( 此
J )” key to edit the parameters, and press the “Enter” key ( 此
I ) to proceed the next setting. The
A
A
E
A
A
E
A
E
A
A
E
A
E
A
A
E
A
Atmospheric pressure compensation:
Press and hold the "▼" key ( 此
J ) to turn the compensation function on/off. The gas compensation is only for
CO2 and O2.
A
E
A
Rechargeable Batteries
Buzzer on/off:
operation, if AL L or AL H buzzer
I ) to turn the buzzer on/off. During
Press the “Enter” key ( 此
A
sounds,
E
A
Battery message:
stops to operate. At this time, press the “Enter” key ( 此
I ) to turn off the buzzer and
A
E
A
continue
. In addition, the buzzer will be automatically turned off when the data logging interval time
is 舛5 minutes.
Buzzer AL L/AL H:
When AL L is on, the buzzer sounds "Ta Ta Ta"; when AL H is on, the buzzer sounds "Bi Bi Bi".
RS485 communications:
Please use the 4 Pole 3.5mm headphone plug. The headphone plug contacts are defined as below:
刈
For long-distance communication, it is necessary to use a dedicated isolated line to ensure communication
quality. The wiring method is as below:刈
‘Battery OK’:
Measurements are possible
‘Battery Low’:
The battery needs to be recharged,
measurements are still possible
‘Battery Exhausted’:
Measurements are not possible
Battery installation:
This device is supplied with Li-ion 18650 3.7V rechargeable battery *3 pcs.
Please confirm whether batteries + polarity are Li ion18650 positive bump specification and install batteries in
the correct polarity. If the battery polarity is reversed, the capacity will be insufficient and the battery life will be
shortened.
Battery charging:
The charge lamp ( 此
E ) lights up while charging; the charge lamp ( 此
E ) goes off when charging is completed.
(5V/1A USB adapter charger)
Note: During battery charging, the temperature of the device will rise by 5°C~10°C. At this time, the
measurements of temperature and humidity will be affected by temperature rise. Cause an impact on
the accuracy of temperature when charging, please use a fan to blow toward the temperature sensor
(此
C ) directly in order to get a compensated balance of temperature and humidity between temperature
sensor and surrounding area.
A
A
E
E
A
A
E
A
A
Safety Instructions
Power off:
Switch the Power Key ( 此
A ) off.
Note: When the device is charged with USB, it cannot be turned off.
A
E
A
Calibration:
(1) Single-point calibration
At the same time, long press “▲( 此
G )“ and “▼( 此
J )“ key, CAL is displayed on the screen. Press the “M1” key
(此
F ) to select the sensor that needs to be calibrated. Press the “▲( 此
G )/▼( 此
J )” key to edit the parameters,
and then press the “Enter” key ( 此
I ) to proceed the next setting. Zone1 displays the unadjusted raw value;
Zone2 displays the adjusted value, and it is also the value of returning to the main screen;
F ) to return to
Zone1-Zone2=adjustment amount. After finishing the setting, press and hold the “M1” key ( 此
the main screen.
A
A
E
E
A
A
E
A
A
A
A
E
E
A
A
E
A
A
A
E
A
(2) Two-point calibration
At the same time, long press “▲( 此
G )“ and “▼( 此
J )“ key, CAL is displayed on the screen. And then long
press the “M2” key ( 此
H ), CAL L is displayed on the screen. Next, press the “M1” key ( 此
F ) to select the
sensor that needs to be calibrated (CO2àCOàO2àNH3àPM2.5àRHàAMB) and the corresponding unit
will blink. Press "▲( 此
G )/▼( 此
J )" key to adjust the value of the standard gas concentration. Press “Enter“ key
(此
I ) to switch CAL H (High gas concentration calibration)/CAL L (low gas concentration calibration). The
ppm unit is not flashing for a moment, indicating that the calibration value has been stored. Long press the
H ) for a calibration calculation. At the same time, the screen displays the calibration reading to
“M2” key ( 此
confirm the accuracy. Short press the “M1” key ( 此
F ) to set the next gas calibration, or long press the “M1” key
(此
F ) to return to the main screen.
A
A
A
A
E
E
E
A
E
A
A
A
A
A
E
E
A
A
A
A
E
A
A
A
E
A
E
E
Warning: Your safety is very important to us. To ensure to use the device correctly and safely, we would like
to draw your attention to read the warning and entire User Manual before using the device. These
are important safety information and should be observed at all times.
1. Please handle the device lightly, do not subject the device to impact or shock.
2. Do not immerse the device in water. Water can cause electric shock, fire or malfunction which may result in
damage.
3. Do not keep the device under the hot and moisture environment. Keep the device away from the heat
source or near water.
4. Please use a standard USB power supply (such as PC's USB port, universal AC adapter with USB port).
Improper power supply can cause serious damage to the device, or result in injury or death to the user.
A
Product Care
To ensure you receive the maximum benefit from using this device, please observe the follow guidelines.
1. The maximum capacity of the SD card is 16G.
2. During battery charging, the temperature of the device rises. The temperature and humidity sensors are
affected. At this time, measurements are only for reference. After batteries are fully charged and the device
cools down, measurements are reliable.
3. Repair – Do not attempt to repair the device or modify the circuitry by yourself. Please contact with the
local dealer or a qualified repairman if the device needs servicing.
4. Caution – The CO and NH3 sensors must be replaced every 3 years.
5. Cleaning – Disconnect the power before clean. Use a damp cloth, do not use the liquid cleaning agent,
such as benzene, thinner or aerosols.
6. Maintenance – Recommend that the user conducts a comprehensive test and calibration every year to
ensure the normal operation of the device.
Specifications
A
CO2
刈
Clear Two-point calibration:
Set the same calibration value for CAL L and CAL H, and then proceed the calculation. After the calibration is
completed, the original calibration value is cleared.刈
CO
O2
NH3
PM2.5
PM10
RH
Temperature
Barometer
Operating
Conditions
Storage
Temp.
Measurement Range
0~9,999 ppm
(5,001~9,999 ppm
over range)
0~1,000 ppm
0~25%
0~100 ppm
Accuracy
±50 ppm or 5% of reading,
whichever is greater (0~5,000ppm)
Display Resolution
1 ppm
±5%~±10%
1 ppm
<2% FS/0.1 mbar
0.01%
±10%
1 ppm
±15%
or
±15
μg/m³,
whichever
is
999 ug/m3
1 ug/m3
greater
0~100%
±2%@25°C (20% RH~80% RH)
0.01%
0°C~50°C
±1°C
0.01°C
50 ~110 Kpa
±0.4 kpa
0.1 mmHg
0~40°C(32°F~104°F),0~95%RH, non-condensing, with lithium-ion batteries
0~50°C(32~122°F), 0~95%RH, non-condensing, without lithium-ion batteries
-20~60°C(-4~140°F), 0~85%RH, non-condensing, without lithium-ion batteries
Rechargeable Battery : Li-ion 18650 3.7V *3 (batteries not included)
Power
Supply
AC Adapter : 5V±5% >1A, 100~240 VAC, 50/60 Hz
Storage
depend on SD card capacity (max.16G SD card)
Capacity
Comm.
RS485 ModBus BR19200劣N劣8劣1
Interface
Alarm
80db±5%@10cm
Volume
Weight
305g (without batteries)
Dimension
204.5x91.7x49.6 mm (8.1x3.6x2 inch)
EMC/RFI: Readings may be affected if the unit is operated within radio frequency electromagnetic field
strength of approximately 3 volts per meter, but the performance of the instrument will not be
permanently affected.
Installation Instruction
P ) or hang it on the wall.
1. You can put ZG906CMONP on the table (please pull out the Housing Stand 此
E
A
A
2. Please note the following when hanging it on the wall. Choose a suitable location to install ZG906CMONP,
fix a刈
screw to the wall.
Package contents
Handheld multi gas detector
Manual
USB 1.5M cable
Radiant Innovation Inc. Http://www.ZyAura.com
1F, No.3, Industrial East 9th Road, Science-Based Industrial Park, HsinChu,
Taiwan 300.
Ref.No.危102018