Workrite Ergonomics Conform STS Sit-to-Stand Monitor Arm Installation Instructions

Assembly & Installation Instructions:

Conform Sit-to-Stand Arm CONF-STS-WOPB-S

Parts Included

A

14" Pole with

HD Base

Qty: 1

B

Adhesive Pads

Qty: 1

D

U-Bracket

Qty: 1

F

Conform Sit-Stand

Articulating Arm

Qty: 1

C

Grommet Bolt, Wing

Nut & M8 Steel Washer

Qty: 1

E

Single Pole Adaptor

Qty: 1

G

Pivot Cover Cap

Qty: 1

CONF-PB-14HDCCG-S

Tools Supplied

H

M2.5 Allen wrench

Qty: 1

I

M4 Allen wrench

Qty: 1

J

M5 Allen wrench

Qty: 1

Monitor Hardware

K

Monitor Screws, Medium

Qty: 4

L

Monitor Screws, Short

Qty: 4

1

HD Base C-Clamp Installation

Note: If you are installing using a grommet, skip to Step 2.

1.1 Using C-Clamp handle, loosen the C-Clamp on the Pole Base (A) wide enough to fit over the edge of the worksurface.

A

1.2 For thinner tops: Adjust the C-Clamp lower plate if it is too wide to fit over the edge of the worksurface. To adjust, remove the screws using the 5 mm

Allen wrench (J). Slide the C-Clamp lower plate to the upper screw holes, replace the screws and tighten until secure.

1.3 Remove Adhesive Pad (B) backing. Apply the pad to the bottom surface of the base, adhesive side up, so that it aligns with the front edge of the base and sticks in place.

1.4 Place C-Clamp over the rear edge of the worksurface and tighten the clamp by turning the C-Clamp Bolt until secure.

Skip to Step 3.

Tighten

1.1

Loosen

A

B

1.3

1.2

1.4

For thinner tops

J

Tighten

Loosen

1 of 4 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

2

HD Base Grommet Mount Installation

Note: A grommet hole or small hole is required in your worksurface to install the grommet mount. Drill a

.375″hole in worksurface if needed. The minimum distance from the edge of the worksurface to the center of the grommet hole is 2.125". The grommet mount can accommodate existing grommet holes up to 3" in diameter.

2.1 Using the C-Clamp handle, loosen the C-Clamp bolt on the Pole Base (A).

2.2 Using 5 mm Allen Wrench (J), remove the Bolt from the underside of the Base in order to remove the entire

C-Clamp in one piece.

2.3 Remove the Adhesive Pad's (B) backing. Apply the adhesive side to the bottom of the Desk Base, aligned with the front edge of Base, and stick in place.

2.4 Insert Grommet Bolt (C) into the Pole Base (A). Tighten with 4 mm Allen Wrench (I).

2.5 Insert the Grommet Bolt (D) through the grommet hole of worksurface. Make sure the mount does not overlap the edge of the worksurface.

2.6 From under the worksurface, place the U-Bracket (D) onto the Grommet Bolt (C) then place the M8 Steel Washer

(C) followed by the Wing Nut (C) onto the Bolt and tighten Wing Nut to secure the base to the desktop.

B 2.3

A

Remove

Bolt

2.2

Remove

C-Clamp

J

2.1

Loosen

Tighten

C

2.4

I

2.6

C

2.5

C

C

D

Worksurface edge

3

Attach Single Pole Adaptor to Pole

3.1 Slide the Single Pole Adaptor (E) onto the 14" Pole (A). You may need to loosen the Clamp Screw using the 5 mm Allen Wrench (J) to slide it onto the Pole.

3.2 Attach at approximately the right height and tighten in place using the 5 mm Allen Wrench (J).

J

3.1

Loosen

2 of 4

E

Clamp screw

A

3.2

J Tighten

Workrite Ergonomics | 800.959.9675 www.workriteergo.com

4

Remove Single Pole Adaptor Bolt & Washers

Remove the Bolt & two Washers from the Single Pole Adaptor (E) and set aside for Step 5. Leave the Pin and Spacer in place.

Remove

Pin

Spacer

A

Bolt

Washers

E

5

Attach Arm to Single Pole Adaptor

5.1 Place the Sit-Stand Articulating Arm (F) onto the Pin on the Single Pole Adaptor (E).

5.2 Attach using The Pin and Washers set aside in Step 4, and tighten using the 5 mm Allen Wrench (J).

5.3 Set the tension screw with the 2.5 mm Allen wrench (H) so the Arm moves freely but remains in place during use.

5.4 Place the Pivot Cover Cap(G) on top of pivot hole.

F

G

5.3

J

5.2

Replace

5.1

E

H

Behind Single

Pole Adaptor

A

3 of 4 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

6

Mount Monitors to VESA Plate

If possible, use the included Monitor Mount screws to attach your monitor to the VESA plate. Otherwise use the shortest screws possible from the included hardware kit (K or L) .

100 mm VESA standard, use 4 outer corner holes.

75 mm VESA standard, use 4 inner corner holes.

Important Note:

It is strongly recommended to use the mounting screws provided by the monitor manufacturer if possible. If longer screws are required, use the shortest screws possible to avoid damage to the monitor.

Remove

Screws that came with monitor or

K or L

7

Monitor Tilt Capacity Adjustment

If your monitor is too light or too heavy for the factory set capacity, the monitor will tilt too easily. If this is the case, you need to adjust the tension.

7.1 Adjusting Tilt Capacity

To increase capacity(+) turn clockwise using the

5 mm Allen wrench (J) until the monitor reaches a balanced adjustment.

To decrease capacity(-) turn counter-clockwise until the monitor reaches a balanced adjustment.

7.2 Adjusting Arm Capacity (opposite of above)

To increase capacity(+) turn counter-clockwise using a 5 mm Allen Wrench (J) until the arm reaches a balanced adjustment.

To decrease capacity(-) turn clockwise until the arm reaches a balanced adjustment

4 of 4

7.1

Tilt capacity

7.2

Arm capacity

Workrite Ergonomics | 800.959.9675 www.workriteergo.com

1500411 Rev A