- Computers & electronics
- TVs & monitors
- Flat panel desk mounts
- Workrite Ergonomics
- Conform C-Clamp & Grommet Base
- Installation instructions
Workrite Ergonomics Conform C-Clamp & Grommet Base Installation Instructions
Add to My manuals3 Pages
advertisement
Assembly & Installation Instructions:
Conform C-Clamp & Grommet Base CONF-BSE-CCG-S
Parts Included
A
Desk Base Set
Qty: 1
B
Adhesive Pad
Qty: 1
E
U-Bracket
Qty: 1
G
Grommet Bolt, Wing
Nut & M8 Steel Washer
Qty: 1
F
Hole Cover Cap
Qty: 1
C
Cable Management Clip
Qty: 1
D
M3×6 mm Screws
Qty: 2
Required Parts Sold Separately
Conform Monitor Arm.
H
2.5 mm Allen Wrench
Qty: 1
I
4 mm Allen Wrench
Qty: 1
J
5 mm Allen Wrench
Qty: 1
Tools Required
A Phillips head screwdriver and included Allen Wrenches.
If a grommet mount hole is required, you'll need a drill and .375" bit.
Do not use on hollow core tables.
Do not exceed 48 lb.
1
Attach Cable Management Clip
Use M3 × 6 mm screws (D) to attach the Cable Management Clip (C) to the Conform Base (A) with Phillips head screwdriver.
A
D
1 of 3
Note:
If you plan to use C-Clamp Mount, proceed to Step 2.
If you plan to use Grommet Mount, proceed to Step 3.
C
Workrite Ergonomics | 800.959.9675 www.workriteergo.com
2 a b c d
C-Clamp Installation
Using 5 mm Allen wrench (J), loosen the C-Clamp bolt on the Desk Base (A) wide enough to fit over the edge of the worksurface.
Remove the Adhesive Pad (B) backing. Apply the pad to the bottom surface of the base, adhesive side up, so that it aligns with the front edge of the base and sticks in place.
Place C-Clamp over the rear edge of the worksurface
Tighten the clamp by turning the C-Clamp Bolt clockwise, using 5 mm Allen wrench (J) until secure.
B b
Loosen a
A
J
Loosen
Tighten d
A
J c
Tighten
2 of 3 Workrite Ergonomics | 800.959.9675 www.workriteergo.com
3 a b g f c d e
Grommet Mount Installation
Note: A grommet hole or small hole is required in your worksurface to install the grommet mount.
Drill a .375″hole in worksurface if needed. The minimum distance from the edge of the worksurface to the center of the grommet hole is 2.125"
The grommet mount can accommodate existing holes up to 3" in diameter.
Using 5 mm Allen wrench (J), loosen the C-Clamp bolt on the Desk Base (A) to remove C-Clamp from the Base. Also remove the C-Clamp bolt.
Remove the pad's pre-punched hole and remove the adhesive cover. Apply the adhesive side to the bottom of the Desk Base, aligned with the front edge of Base, and stick in place.
Insert Grommet Bolt (G) through the adhesive pad's hole and into the Desk
Base (A). Tighten with 4 mm Allen Wrench (I).
Insert the installed Desk Base Bolt (G) through the grommet hole of worksurface.
Make sure the mount does not overlap the edge of the worksurface.
From under the worksurface, place the U-Bracket (E) onto the Grommet Bolt (G) then place the M8 Steel Washer (G) followed by the Wing Nut (G) onto the Bolt and tighten Wing Nut to secure the base to the desktop.
Insert Hole Cover Cap (F) to cover the C-Clamp bolt hole.
F g c
Loosen b
J
Remove
A
Remove
Hole e
≤2.125
" a
Tighten
G d
I
E f
Tighten
G
4
Ready for Arm Installation
You are now ready to attach your selected Conform Monitor Arm (sold separately).
3 of 3
≤2.125
"
Workrite Ergonomics | 800.959.9675 www.workriteergo.com
#1500250 Rev E
advertisement
Related manuals
advertisement