Workrite Ergonomics Sit Stand Desks Disassembly Instructions

Disassembly Instructions:

Adjustable Work Centers

Workrite Ergonomics | 800.959.9675 www.workriteergo.com 1 of 6

Tools Required:

Cordless Drill 7/16” Wrench #2 Phillips Bit

Screwdriver or

Driver/Drill

3mm Allen Wrench 4mm Allen Wrench 5mm Allen Wrench

NOTE:

• Example shown is for 3-leg table, the same steps can be followed for 2 or 4-leg tables.

• Not all images are representative of all Workrite Adjustable Work Centers.

1 a

Disconnect the Power Supply from Workcenter.

Turn the Work Center upside down.

1a

2 of 6 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

d e f b c g

2 a

Steps to remove Cables and Cable Loops.

Remove the Leg Cables from ports on the Control Box.

Remove Extension Cable from port on the Control Box.

Remove the Control Cable from the switch port on the Control Box.

Remove the Power Cable from the power port on the Control Box.

Unscrew Pan Head Screw from Cable Loops and remove them from underside of worksurface.

Dispose of Cables in Electronic Waste per Local Ordinance.

Save Screws for recycling.

2e

2e

2c

Remove

Switch Cable from Switch

Port “HS"

2b

Remove

Leg Cable or

Extension from

Leg Ports “M1",

“M2" & M3

2a

2a

Workrite Ergonomics | 800.959.9675 www.workriteergo.com

Remove

Power Cable from Power Port

2d

3 of 6

b c

3 a

Steps to remove Workrite Switch.

Unscrew two Pan Head Screws and remove the switch from underside of worksurface.

Dispose of Switch in Electronic Waste per Local Ordinance.

Save Screws for recycling.

3a

Programmable Switch shown

4 a b c d

Steps to remove Control Box & Cable Spool from Worksurface.

Unscrew two Pan Head Screws and remove Control Box.

Unscrew Pan Head Screw and remove Cable Spool.

Dispose of Control Box in Electronic Waste per Local Ordinance.

Save Screws for recycling.

4a

4a

4b

4b

4b

4 of 6 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

b c d

5 a

Steps to remove Feet.

Using Allen Wrench, unscrew Flat Head Cap Screws and remove Center Foot from bottom of Center Leg.

Using Allen Wrench, unscrew Flat Head Cap Screws and remove Feet from bottom of Center Leg.

Dispose of Feet in Metal Recycling per Local Ordinance.

Save Screws for recycling.

5a

5b b c

6 a d

Steps to remove Base from Worksurface.

Remove all Pan Head Laminate Top Screws that secure the base to the laminate surface.

Save Screws for recycling.

Remove Splice Bracket & Draw Bolt from Table Top, and save for recycling.

Dispose of laminate per local ordinance.

6a 6a

6b

Workrite Ergonomics | 800.959.9675 www.workriteergo.com

REMOVE

6b

1500476 Rev A

5 of 6

7 a b c d

Steps to remove Short and Medium Brackets.

Unscrew Flat Head Cap Screws then remove Connected Rear Bracket and Floating Rear Bracket.

Unscrew Flat Head Cap Screws then remove Right End Bracket from Right Leg, remove Left End Bracket from Left

Leg, and remove Corner End Bracket from Center Leg.

Unscrew Flat Head Cap Screws then remove Short Brackets from all there Legs.

Save Screws for recycling.

7a

Connected Rear Bracket

7a

Floating Rear Bracket

Right Leg Left Leg

7b

Right End Bracket

8

7c 7c

7b

Left End Bracket

Steps to remove Rear Bracket from Connector Bracket.

a b c

Unscrew Flat Head Cap Screws, then removeRear Bracket from

Connector Bracket.

Dispose of Base (three Legs, End Brackets, Short Brackets,

Connector Bracket and Rear Brackets) in Metal Recycling.

Save Screws for recycling.

8a

8a

1500476 Rev A

6 of 6 Workrite Ergonomics | 800.959.9675 www.workriteergo.com