Universal Link Tx/Rx
RMCARD205
Universal Port
Tx/Rx Indicator
LINK Indicator
Ethernet Port
Quick Start Guide
REMOTE MANAGEMENT CARD
RMCARD205
RMCARD305
The Remote Management Card allows a UPS/ATS system and environmental sensor to be managed, monitored, and configured.
K01-0000449-01
INSTALLATION GUIDE
Step 1. Hardware Installation
1. Remove the two retaining screws of the expansion slot, and then remove the cover.
RMCARD205 RMCARD305
2. Install the CyberPower
Remote Management Card into the expansion slot.
3. Insert and tighten the retaining screws.
4. Connect an Ethernet cable to the
Ethernet port of the CyberPower
Remote Management Card.
CyberPower
Univ ersal
Link
RM
CARD205
CyberPower
Univ ersal
RM
CARD205
RMCA
Universal
RD30
5
Link
Tx/Rx
CyberPower
RMCA
RD30
Univ ersal
5
Tx/Rx
CyberPower
5. (Optional) To connect with the environmental sensor, use a RJ45
Ethernet cable. Connect one end to the Universal port on the RMCARD and the other end into the sensor.
For more information, please see the ENVIROSENOR user’s manual.
erPower sal
Tx/Rx
RM
CARD205
RM
CARD305 sal
Tx/Rx
CyberPower
NOTE: The CyberPower Remote Management Card is hot-swappable, so you do not need to turn off the device to install it.
Universal
RMCARD305
Link Tx/Rx
Definitions for LED Indicators
Link LED color
Off
Condition
The Remote Management Card is not connected to the Network/ or the Remote
Management Card power is off
On(Yellow) The Remote Management Card is connected to the Network
Tx/Rx LED color
Off
The Remote Management Card power is off
On(Green)
Flash
The Remote Management Card power is on
- Receiving/transmitting data packet
- Reset finished
Step 2. Configure the IP address for the CyberPower
Remote Management Card
Method 1: Using the Power Device Network Utility
1. Install the Power Device Network Utility available for download on the
Network Power Management product web page at www.CyberPower.com.
2. After installation completes, run the “Power Device Network Utility”.
3. The main dialog of the Power Device Network Utility program is shown in Figure 1. The configuration tool will display all CyberPower Remote
Management devices present on the same network subnet. The
"Refresh" button is used to search the local network subnet again.
Figure 1. The main window of the “Power Device Network Utility” program.
4. Select the Remote Management Card you are setting up. Click on the
Tools menu and select “Device Setup” or double click the Remote
Management Card you want to configure.
5. You can modify the IP Address,
Subnet Mask, and Gateway address for the Device MAC
Address listed in the Device
Network Settings window, as shown in Figure 2. The factory default IP Address is
192.168.20.177 and the default
Subnet Mask is 255.255.255.0.
6. Modify the IP, subnet mask or gateway address. Enter the new addresses into the corresponding fields and then click “Save”.
Figure 2. The Device Network setting window.
7. You will need to enter a User Name and Password for the Remote
Management Card in the authentication window, as shown in
Figure 3.
- Default user name: cyber
- Default password: cyber
8. If the IP address change is successful, you will see a message confirming the IP set up is OK, as shown in Figure 4.
Figure 3. Authentication window.
Figure 4. Setup IP Address successfully message.
Method 2: Using a command prompt
1. Obtain the MAC address from the label on the Remote Management
Card. Each Management Card has a unique MAC address.
2. Use the ARP command to set the IP address.
Example:
To assign the IP Address 192.168.10.134 for the Remote Management
Card, which has a MAC address of 00-0C-15-00-FF-99 you will type in the following in the command prompt from a PC connected to the same network as the Remote Management Card.
(1) Type in “arp -s 192.168.10.134 00-0C-15-00-FF-99” then press
Enter.
3. Use the Ping command to assign a size of 123 bytes to the IP.
(1) Type in “ping 192.168.10.134 -l 123” then press Enter.
(2) If the replies are received, your computer can communicate with the
IP address.
NOTE: These instructions are for Windows OS. For other OS please refer
to RMCARD User’s Manual available for download at CyberPower
Systems official website: www.CyberPower.com.
SOFTWARE SUPPORT
PowerPanel ® Business Edition Client can support a CyberPower Systems device with a remote management card via the network. PowerPanel ®
Business Edition software is available on CyberPower Systems official website. Please visit www.CyberPower.com and go to the software section for free download.
CONFORMANCE APPROVALS
FCC Warning
This equipment has been tested and found to comply with the limits for a
Class A Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Any special accessories needed for compliance must be specified in the instruction.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulation.
Cet appareil numerique de la class A respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada.
WEB INTERFACE Login User Account
You can select a preferred language, and will need to enter a User Name and Password to login to the interface. There are two user account types.
1. Administrator
- Default username: cyber
- Default password: cyber
2. View only
- Default username: device
- Default password: cyber
The administrator can access all functions, including enable/disable the view only account. The viewer can access read only features but cannot change any settings.
Troubleshooting
Problem
Unable to configure the Remote
Management Card by method 1 or method 2
Solution
1. Check the LED status, the condition is normal when the yellow and green LEDs are both on.
If green LED is off :
►Check if the Remote Management Card is
properly seated in the device and the device
power is turned on.
If yellow LED is off :
►Ensure the network connection is good.
2. Ensure the PC being used is on the same network subnet as the CyberPower device you are trying to communicate with.
Unable to ping the
Remote
Management Card
1. Use method 1 and/or method 2 to get/set a correct
IP address for the Remote Management Card.
2. If the PC being used is on a different network subnet from the Remote Management Card, verify the setting of subnet mask and the IP address of gateway.
Lost the user name and password
Please refer to the “ Reset to Default Setting /
Recover from a Lost Password” section in the
RMCARD User’s Manual.
CyberPower Systems, Inc.
www.cyberpower.com
For USA and Canada:
4241 12th Ave East, Suite 400
Shakopee, MN 55379
Toll-free: (877) 297-6937
For all other regions:
Please visit our website for local contact information.
