- Computers & electronics
- Audio & home theatre
- Video converters
- Ponca Technologies
- PT?1232
- User manual
advertisement
▼
Scroll to page 2
of 7
PONCA Technologies 3G/HD/SD-SDI to HDMI Converter User Manual PT‐1232 Safety and Notice The PT-1232 3G/HD/SD-SDI to HDMI Converter has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipments, the PT-1232 should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit. z Follow all instructions and warnings marked on this unit. z Do not attempt to service this unit yourself, except where explained in this manual. z Provide proper ventilation and air circulation and do not use near water. z Keep away the objects that might damage the device and assure that the placement of this unit is on a stable surface. z Use only the power adapter, power cords and connection cables designed for this unit. z Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning. ~1~ Introduction The PT-1232 provides a cost effective way to convert 3G/HD/SD-SDI signal to HDMI compliant format. The conversion between SDI and HDMI is pure digital and guarantees no loss transformation for both audio and video. Plus, with up to 8 channels audio support, 7.1 channel or 5.1 channel audio becomes available. The PT-1232 also provides 2 low jitter and re-clocked outputs for daisy chain or multiple monitors. Features z Supported 3G formats(SMPTE 425M, Level A): 1080p @50/59.94/60Hz (4:2:2) z Supported high-definition (HD) formats: 1080i @50/59.94/60Hz, 1035i @50/59.94/60Hz, 720p @50/59.94/60Hz z Supported standard-definition (SD) formats: NTSC @59.94Hz, PAL @50Hz z Auto 3G/HD/SD-SDI detection z Two equalized and re-clocked loop outputs z External DIP Switch Configuration ~2~ Specifications & Package Contents Model Name Technical SDI standards Auto 3G/HD/SD-SDI detection Video bandwidth Video support Input signal Output signal Audio mode Eye pattern characteristics Cable equalization Loop-out Audio support PCB stack-up Input Output BNC connector HDMI connector DIP switch Mechanical Housing Model Dimensions Package (L x W x H) Carton Model Weight Package Fixedness Power supply Power consumption Operation temperature Storage temperature Relative humidity Package Contents PT-1232 SD-SDI, HD-SDI & 3G-SDI Yes 2.970Gpbs, 2.970/1.001Gbps [3G] – 1080p @50/59.94/60Hz (4:2:2) [HD] – 720p @50/59.94/60Hz, 1035i @50/59.94/60Hz, 1080i @50/59.94/60Hz, 1080p @24/30Hz [SD] – NTSC @59.94Hz, PAL @50Hz [SD-SDI] SMPTE 259M [HD-SDI] SMPTE 292M, 296M [3G-SDI] SMPTE 424M/425M HDMI 7.1/5.1/Stereo Extra low alignment jitter 0.05UI at HD [3G-SDI] up to 60m (200ft) [HD-SDI] up to 150m (500ft) [SD-SDI] up to 300m (1000ft) 2 equalized and reclocked SDI loop-outs Yes 4-layer board [impedance control — differential 100Ω; single 50Ω] 1x BNC [SDI] 1x HDMI 2x BNC [SDI] 3G 75Ω inter-locked socket Type A [19-pin female] 4-pin [output format / audio format / audio group / 3G level] Metal case 175 x 120 x 25mm [6.9” x 4.7” x 1”] 265 x 175 x 75mm [10.4” x 6.9” x 3”] 450 x 370 x 300mm [1’6” x 1’3” x 1’] 530g [1.2 lbs] 995g [2.2 lbs] Inter-locked power supply 5V 4A DC 3 Watts [max] 0~40°C [32~104°F] -20~60°C [-4~140°F] 20~90% RH [no condensation] 1x PT-1232 1x 5V power adapter 1x User Manual ~3~ Supported Resolutions 3G-SDI INPUT 1080p @ 60/59.94/50Hz SMPTE 425M (4:2:2) HD-SDI INPUT 720p @ 50Hz SMPTE 296M -3 720p @ 60 / 59.94Hz SMPTE 296M -1, -2 1080i @ 25Hz SMPTE 274M -6 1080i @ 30 / 29.97Hz SMPTE 274M -4, -5 1080p @ 24 / 23.98Hz SMPTE 274M -10, -11 1080p @ 25Hz SMPTE 274M -9 1080p @ 30 / 29.97Hz SMPTE 274M -7, -8 SD-SDI INPUT NTSC PAL B,D,G,H,I ~4~ Panel Descriptions Front Panel 1 2 3 1. 2. 3. 4. 4 3G/HD/SD-SDI Input Lock LED 3G/HD/SD-SDI Output #1 3G/HD/SD-SDI Output #2 Rear Panel 5 5. HDMI output 6. Interlocked +5V power jack 6 Bottom Panel A 4-pin DIP switch is used for user interface, and users can access this switch from the bottom of the unit. Output formats, video patterns, SD Pedestal, SD Wide, PAL mode, YPbPr / RGB, SD component or SD composite, YC on/off etc. Pin # OFF (©) ON (ª) Pin OFF (©): 1 2 HDMI Mode 7.1ch DVI Mode Stereo Pin ON (ª): 3 Audio group 1&2 Audio group 3&4 ~5~ 4 Audio Mute Off Audio Mute On Notice 1. PT-1232 mainly checks the audio channel in audio group 1&2 or 3&4. Please adjust DIP switch pin 3 for setup. 2. Some HDMI equipped TV may not be able to decipher multiple channel audio, and therefore set DIP switch pin-2 to ON(ª) to get stereo audio work and then check if multiple channel support is available. 3. While DIP Switch pin-4 is set to OFF(©), 3G Level B will be automatically converted to Level A. 4. PT-1232 supports only audio sample frequency 48kHz. 5. While stereo audio is chosen, CH 1 & 2 of Group 1 or 3 are output. Limited Warranty The SELLER warrants the PT-1232 3G/HD/SD-SDI to HDMI Converter to be free from defects in the material and workmanship for 1 year from the date of purchase from the SELLER or an authorized dealer. Should this product fail to be in good working order within 1 year warranty period, the SELLER, at its option, repair or replace the unit, provided that the unit has not been subjected to accident, disaster, abuse or any unauthorized modifications including static discharge and power surge. This warranty is offered by the SELLER for its BUYER with direct transaction only. This warranty is void if the warranty seal on the metal housing is broken. Unit that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair. Such repairs are warranted for 90 days from the day of reshipment to the BUYER. If the unit is delivered by mail, customers agree to insure the unit or assume the risk of loss or damage in transit. Under no circumstances will a unit be accepted without a return authorization number. The warranty is in lieu of all other warranties expressed or implied, including without limitations, any other implied warranty or fitness or merchantability for any particular purpose, all of which are expressly disclaimed. Proof of sale may be required in order to claim warranty. Customers outside USA are responsible for shipping charges to and from the SELLER. Cables and power adapters are limited to a 30 day warranty and must be free from any markings, scratches, and neatly coiled. The content of this manual has been carefully checked and is believed to be accurate. However, The SELLER assumes no responsibility for any inaccuracies that may be contained in this manual. The SELLER will NOT be liable for direct, indirect, incidental, special, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages. Also, the technical information contained herein regarding the PT-1232 features and specifications is subject to change without further notice. ~6~
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project