LIGHTWARE TPS-PI-1P1 Single Port Standalone TPS Power Injector User Guide

Front and Rear Views
Typical Application - Remote Powering
Typical Application - Local- and Remote Powering
S
n:
AT7
in RoH
EU S
,H
un
ga
ry
C
P
w
ith
S
FT
Lo
ng
e
oE
bl
P
ca
TP
S
d
orte
pp
su
0
, 4K
3D 10/10 l IR
-232
RS
MI, et
na
HD hern ctio nal
Et dire ctio
Bi dire
Bi
or
ad
e
D
(IE evic
Fo EE e ca
r 80 n
be 2.
st 3a be
pe f) re
m
rf
ot
or
e
m
po
an
w
ce
er
us
ed
e
ov
A
W
er
G
TP
23
S
C
lin
AT6
k
M
PI
12 N:
V 2m
1A m
D
C
is
ta
nc
e
D
ec
R
ei
ve
r
HD
MI-
TP
X9
S-R
7
1
: 0.5A
ical A
Typ : 1.25
Max- +
IN
(Po
.5A
x:2
Ma
48V DC
Power adaptor
HDMI-TPS-RX95
TPS-PI-1P1
PIN: 2mm
PIN: 2mm
48V DC
Power adaptor
12V DC
Power adaptor
HDMI-TPS-RX97
E)
S
TP
.5A
x:2
Ma
: 0.5A
ical A
Typ : 1.25
Max- +
TPS-PI-1P1
CATx
O2
DI
AU
E
LIV-232
RSVC
SR K
LIN
IR
IN
Local
DC-DC
cable
CATx
I IN
DV
T
IN
IR
OU
IO
GP
O2
DI
AU
IN
PIN:
I IN
DV
mm
Power send
-232
RS
2.1
V 1A
TX
RX
DC
12
E
LIV-232
RSVC
SR K
LIN
IR
T
IN
IR
IO
GP
PIN:
Quick Start Guide
mm
Power send
CATx
-232
RS
2.1
V 1A
UMX-TPS-TX140
CATx
OU
TX
RX
DC
12
2
TPS-PI-1P1
3
1 Status LEDs
2 48V DC in
3 TPS port (not powered)
4
5
UMX-TPS-TX140
4 TPS port (powered)
5 12V DC out
Important Safety Instructions
Installation
Powering Options
Status LEDs
Please read and keep the information in the attached safety instructions supplied with the
product before you start using the device.
1. Switch off (disconnect) all units, even the video, audio or data devices. Make sure there
are no powered units during the installation.
2. Connect the TPS device to be remote powered (e.g. UMX-TPS-TX140) to the TPS+PoE
connector 2 of the TPS-PI-1P1 Power Injector with a CATx cable.
3. Connect the TPS device to be local powered (e.g. HDMI-TPS-RX95) to the TPS connector
3 of the TPS-PI-1P1 Power Injector with a CATx cable.
4. Connect the desired video, audio and data devices (e.g. Blu-ray players, amplifiers,
Ethernet switch, RS-232 controller, IR transmitter) to the TPS units. Please read the user
manuals of all devices to get help during the installation process.
5. Switch on the devices according to the following sequence:
a. The Power Injector with connecting firstly the 48V DC adaptor to the 48 DC IN con‑
nector 4 secondly to the socket. The remote device gets power immediately.
b. The local powered device
ƒ with connecting its adaptor or
ƒ with connecting the supplied patch cable* to the 12V DC OUT 5 of the Power
Injector.
c. Switch on the other devices.
This unit provides a uni-directional remote power only, but thanks to the 12V DC local output
option the other device (e.g. HDMI-TPS-RX95) can be powered with the TPS-PI-1P1 if they
are placed close to each other while the injector itself is powered by the supplied adaptor.
POWER OVERLOAD
The Power Scheme
 TPS-PI-1P1 does not apply current limitation but only indicates the overload.
Introduction
TPS-PI-1P1 is an IEEE 802.3at compatible high end remote Power Injector (PI) unit providing
power to a remote Powered Device (PD) e.g. TPS transmitter or receiver. The TPS‑PI‑1P1
placed in the TPS transmission chain, anywhere between the transmitter and the receiver unit
via the CATx* cable is able to power a TPS device. The incoming data stays untouched, but a
48V DC remote power is added to the signal by this PI.
* CAT7 AWG 23 SFTP cable is always recommended.
 Comparing to the details of the powered device’s extension distance chart the usage of the
TPS-PI-1P1 may cause approximately 20% distance decrease depending on the powering
mode (local or remote) and cable quality.
Compatible Devices
The power injector can be used to supply power any PoE-compatible Lightware extenders
which are based on TPS-technology, except the TPS-90- and TPS-95-series.
 The TPS-TX/RX90 and TPS-TX/RX95 extenders are not PoE-compatible thus not
able to send/receive power to/from TPS-PI-1P1 power injector.
 Warning! The sum of the power of the two outputs must be under 30W.
Power Injector unit
48V DC power adaptor
with interchangable plugs
12V patch cable for
local power option
48V DC in
12V DC
out
TPS+PoE
DC/DC
TPS
Quick
Start
Guide
Safety and warranty info,
Quick Start Guide
 The 12V DC out cannot be disabled in normal operation. If it is not working please contact
[email protected].
REMOTE POWER OUT ACTIVE
ƒ OFF: there is no PoE compliant device at the remote side or the identification process
was unsuccessful. The Power Injector does not send power over the CATx cable.
ƒ ON: the remote unit is a valid PoE device and gets the power via the TPS line in this case.
48V DC IN PRESENT
ƒ OFF: the 48V DC input is not connected. If it is connected, the voltage level is not enough
for the proper operation (it is lower than 40V DC).
ƒ ON: the 48V DC input is connected and the voltage level is proper (it is lower than 40V
DC).
* CAB-12V-U16U (Part No: 13730013)
 The maximum distance of the TPS units will not expand by using TPS-PI-1P1.
Mounting Options
Ventilation
To mount the device Lightware supplies optional accessories for different usage. There are
three kinds of mounting kits with similar fixing method:
The enclosure of the TPS-PI-1P1 has vent holes on the left and the right side, as well. These
holes provide the cooling by convection.
TAKE CARE OF ME
ƒ Under-desk mounting kit
ƒ Under-desk double mounting kit
ƒ 1U high rack shelf
To order mounting accessory kits please contact [email protected].
Mounting by Using the Under-desk Mounting Kit
d
Safety an
y
Warrant
Info
12V DC OUT ACTIVE
ƒ OFF: the 12V DC out is out of order.
ƒ ON: device is connected to the 12V DC output connector.
 Warning! Always use the supplied power adaptors. Warranty void if damage occurs
due to use of a different power source.
Box contents
ƒ OFF: the delivered power of the wall adaptor is less than 75% of the maximum value.
ƒ ON: the delivered power of the wall adaptor exceeds 75% of the maximum value.
 Warning! Do not block the vent holes otherwise the unit can be overheated.
 The appropriate operation of the unit is not guaranteed with 40V DC or lower input voltage.
In this case if the identification and the classification were successful, the TPS-PI-1P1 switches
the inadequate voltage to the TPS line, but the remote powering can be failed. Always use the
supplied power adaptors of the devices.
I AM THE ONE AND ONLY
USER DOCUMENT FOR
THIS PRODUCT
Lightware Visual Engineering PLC.
Budapest, Hungary
Locking DC Plug
DC cables from Lightware contain locking DC connector that establishes robust and safe
power connection. After plugging it in, turn the plug clockwise as you can see on the following
figure.
 [email protected]  +36 1 255 3800
 [email protected]  +36 1 255 3810
©2023 Lightware Visual Engineering. All rights reserved. All trademarks mentioned are the
property of their respective owners. Specifications are subject to change without notice.
Further information on the device is available at www.lightware.com.
Doc. ver.: 2.4
Twist 90°clockwise to lock.
19210110
Specifications
General
Compliance.....................................................................................................CE, UKCA
EMC (Emission)......................................................................EN 55032:2015+A1:2020
AC power plug............................................. Interchangable (EU, UK, JP/US, AUS/NZ)
DC power plug.................................................................................2-pole Phoenix plug
Enclosure
EMC (Immunity)....................................................................EN 55035:2017+A11:2020
Enclosure material......................................................................................... 1 mm steel
Electrical safety................................................................................... EN 62368-1:2020
Dimensions in mm................................................................... 100.4 W x 67.6 D x 26 H
RoHS......................................................................................................EN 63000:2018
Dimensions in inch................................................................. 3.96 W x 2.67 D x 1.03 H
Warranty.............................................................................................................. 3 years
Weight.........................................................................................................224 g (0.5 lb)
Operating temperature....................................................0° to +50°C (+32° to +122°F)
Operating humidity.......................................................... 10% to 90%, non-condensing
Cooling.................................................................................................................passive
Power
Power supply option................................................................................ Power adaptor
Power consumption................................................................... 4 W (typ.) / 8 W (max.)
Heat dissipation......................................................... 14 BTU/h (typ.), 28 BTU/h (max.)
Power over Ethernet (PoE)...................................... via ‘TPS+PoE’ port (IEEE802.3at)
Power adaptor
Supported power source..........................................................100-240 V AC; 50/60 Hz
Supplied power.....................................................................................48V DC, 500 mA