Tenda RX12 Pro Wi-Fi 6 6E Router Installation Guide

Scenario 1: Set up the device as a router
➊ Power source
II. Connect the router to the internet
1. Start a browser on the client and enter tendawifi.com in the address bar to access the
web UI, or run the Tenda WiFi app.
WiFi-enabled device
Internet
MAC
Quick Installation Guide
SSID:
Tenda_XXXXXX
tendawifi.com
Serial No.
Wi-Fi 6/6E Router
SSID
Tenda_XXXXXX
Pin No.
12345678
Setting
or
Ten d a _ XXXXXX
Modem
RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro
LAN
PWR
RST WPS/MESH WAN
1
2
IPTV/3
WAN
Or
➋
Or
1, 2, IPTV/3
Ethernet cable
Ethernet cable
➌
Download Tenda WiFi App
2. Perform operations as prompted (computer used as an example).
➊ Click Start Now.
Example: RX12 Pro
Wired device
Tips
English
The product appearance may vary with models. Please refer to the product you purchased.
Ethernet jack
Welcome to use Tenda router
Faster, Safer, Smoother, Smarter
Package contents
I. Connect the router
• Wireless router x 1
• Power adapter x 1
• Ethernet cable x 1
• Quick installation guide
➊ Power on the router.
➋ Connect the WAN port of the router to the LAN port of your modem or the Ethernet jack
Tips
If you use the modem for internet access, power off the modem first before connecting the WAN
port of the router to the LAN port of your modem and power it on after the connection.
➋ The router detects your connection type automatically.
• If your internet access is available without further configuration (for example, PPPoE
connection through an optical modem is completed), click Next.
➌ Set the WiFi name, WiFi password and login password for the router.
Click Next.
English
3
4
WiFi Settings
Complete
Internet access is a few steps away!
2
3
Detect Internet Internet Settings WiFi Settings
Connection Type
Detect Internet Internet Settings
Connection Type
4
Complete
➌
using an Ethernet cable.
To access the internet with:
• WiFi-enabled devices: Connect to the WiFi network using the WiFi name and password you set.
• Wired devices: Connect to a LAN port (1, 2, IPTV/2 or IPTV/3) of the router using an Ethernet
cable.
Tips
If you completed the configurations using the Tenda WiFi App and want to remotely manage the
network, tap
on the App home page and use your account to log in.
WiFi Password •••••••••
ISP Type Normal
Password Strength
Internet Connection Type Dynamic IP
Next
Skip
Previous
2
3
The WiFi password is used to connect to the WiFi network, while the login password is used to log
in to the web UI of the router.
Done.
Node Type
Primary node
4
Detect Internet Internet Settings
Connection Type
WiFi Settings
Complete
ISP Type Normal
Select this type if you access the internet using the PPPoE account and PPPoE
password. If you forget the PPPoE user name and password, Import PPPoE
user name and password from the original router.
PPPoE Username Enter the user name from your ISP
PPPoE Password Password from your ISP
Next
Skip
POWER
PWR
Power jack.
RST
Reset
Reset button.
When the router is working normally, hold the button down using a
needle-like item (such as a pin) for about 8 seconds, and then release
it when the LED indicator blinks red fast. The router is reset.
After the router is powered on for about 40 seconds, the system completes startup. The status
of the LED indicator is shown in the following table.
Detection succeeded. Recommended internet connection type: PPPoE
Internet Connection Type PPPoE
Description
LED indicator
Tips
4
Complete
Jack/Port/
Button
Strong
Next
Detect Internet Internet Settings WiFi Settings
Connection Type
Jack, ports and buttons
The jacks, ports and buttons may vary with models.
Set WiFi password to router login password
Select this type if you can access the internet simply by plugging in an Ethernet
cable for internet connection.
• If the PPPoE user name and password are required for internet access, select the ISP Type
based on your region and ISP and enter required parameters (if any). If you forget your
PPPoE user name and password, click Import PPPoE user name and account from the
original router and perform operations as prompted, or you can obtain the PPPoE user
name and password from your ISP and manually enter them. Then, click Next.
Scan to download Tenda WiFi
app
Manage your router easily
Connect your wireless client such as a smartphone to the WiFi network of the router, or
use an Ethernet cable to connect the computer to the 1, 2, IPTV/2 or IPTV/3 port of the
router. The SSID and password can be found on the bottom label of the device.
WiFi Name Tenda_XXXXXX
Detection succeeded. Recommended internet connection type: Dynamic IP
Start Now
Configuration completes. You can access the internet now
Current WiFi network is cut off. Please connect to the new WiFi network
WiFi Name
Tenda_XXXXXX
WiFi Password
Login Password
Complete
Secondary
node
LED indicator
Status
Description
Solid green
The system is starting up, or the router is already
connected to the internet.
Blinking green
fast
The router is pending for or performing WPS
negotiation or Mesh networking.
Blinking red
slowly
The router failed to connect to the internet.
Solid green
Networking succeeds. Good connection quality.
Solid orange/
yellow
Networking succeeds. Fair connection quality.
Solid red
Networking succeeds. Poor connection quality.
Blinking green
fast
Networking by the WPS or WPS/MESH button or
performing WPS negotiation.
Blinking green
slowly
Waiting to connect to another node.
Blinking red
slowly
The router failed to connect the internet.
WPS
WPS/MESH
WAN
WPS/Mesh button.
• WPS: When it is used as a WPS negotiation button, you can
connect to the WiFi network of the router without entering the
WiFi password.
Method: Press this button for about 1–3 seconds. The LED indicator
blinks fast. Within 2 minutes, enable the WPS function of the other
WPS-supported device to establish a WPS connection.
• Mesh: When it is used as a Mesh networking button, you can
extend your network with another device that supports the Mesh
function.
Method: Press this button for about 1–3 seconds. The LED indicator
blinks green fast, which indicates the device is searching for
another device to form a network. Within 2 minutes, press the
MESH/WPS button of another device for 1 to 3 seconds to
negotiate with this device.
10/100/1000 Mbps auto-negotiation WAN port.
Used to connect to a modem or the Ethernet jack using an Ethernet
cable for internet access.
Tips
After the router is connected to an existing network as a secondary
node, this WAN port is used as a LAN port.
1, 2
10/100/1000 Mbps auto-negotiation LAN port.
Used to connect to computers, switches or game machines, etc.
IPTV/3
IPTV/2
10/100/1000 Mbps auto-negotiation LAN/IPTV port.
It is a LAN port by default. When the IPTV function is enabled, it
can only serve as an IPTV port to connect to a set-top box.
Scenario 2: Set up as an add-on node
FAQ
I. Add the router to an existing network
Q1: I cannot log in to the web UI of the router by visiting tendawifi.com.
What should I do?
A1: Try the following solutions:
• If you are using a WiFi-enabled device, such as a smartphone:
− Ensure that it connects to the WiFi network of the router.
− Ensure that the cellular network (mobile data) of the device is disabled.
• If you are using a wired device, such as a computer:
− Ensure that tendawifi.com is entered correctly in the address bar, rather than the
search bar of the web browser.
− Ensure that the computer is connected to the LAN port of the router properly using
an Ethernet cable.
− Ensure that the computer is set to Obtain an IP address automatically and
Obtain DNS server address automatically.
If the problem persists, reset the router by referring to Q2 and try again.
Tips
• Please ensure that the router has never been used. If not, reset it first.
• Currently, RX12, TX12, RX12 Pro, TX12 Pro, RX27 Pro, TX27 Pro, Mesh6X, Mesh12X, Mesh 15XP
and Mesh21XEP can be networked with each other.
1. Place the router in an elevated and open position within 3 meters from your existing node.
2. Use the power adapter to connect the router to a power source, and wait until its
LED indicator blinks green slowly.
3. Press the WPS or WPS/MESH button of the router for about 3 seconds. The LED indicator
blinks green fast. Within 2 minutes, press the MESH/WPS button of the node of the
existing network for 3 seconds to negotiate with this router.
Original node
Q2: How to restore my device to factory settings?
When the LED indicator of the router lights solid green, the networking is successful and the
router becomes a secondary node in the network.
II. Relocate the router
Add-on node
Example: RX12 Pro
Tips
The product appearance may vary with models. Please refer to the product you purchased.
1. Refer to the following relocation tips to locate the router to a proper position:
• Ensure that the distance between any two nodes is less than 10 meters.
• Keep your nodes away from electronics with strong interference, such as microwave
ovens, induction cookers, and refrigerators.
• Place the nodes in a high position with few obstacles.
2. Power on the router again till the LED indicator blinks green slowly.
Tips
If the LED indicator of router keeps blinking green slowly for more than 3 minutes, relocate the router
and move it closer to the primary node.
3. Observe the LED indicator of the router until the LED indicator lights one of the following
colors:
Solid green
Networking succeeds. Excellent connection quality.
Solid orange/yellow
Networking succeeds. Fair connection quality.
Solid red
Networking succeeds. Poor connection quality.
4. If the router's LED indicator blinks red slowly, relocate it by repeating the preceding steps
to get an optimal connection quality.
Done.
To access the internet with:
- Wired devices: Connect to the LAN ports of your nodes.
- Wireless devices: Connect to your WiFi network using the WiFi name and password of your
existing WiFi network.
A2: When your device is working properly, hold down the RST or Reset button of your
device using a needle-like item (such as a pin) for about 8 seconds, and release it when
the LED indicator blinks red fast. When the LED indicator lights solid green, your device is
reset successfully.
Q3: The device failed to be detected by the Tenda WiFi app upon my first time using
the device. What should I do?
A3: Try the following solutions:
1. Ensure that your smartphone is connected to the default WiFi network of the device.
2.Ensure that the network permission of Tenda WiFi app is enabled, you can tap Settings
> Tenda WiFi to enable it.
If the problem persists, please reset the router and try again.
Q4: I cannot find the 5 GHz/6 GHz WiFi network of the router on my WiFi-enabled
device. What should I do?
This equipment should be installed and operated with a minimum distance 20cm between the device and
your body.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a
shielded RJ45 cable.
Declaration of Conformity
Hereby, SHENZHEN TENDA TECHNOLOGY CO., LTD. declares that the device is in compliance with Directive
2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
https://www.tendacn.com/download/list-9.html
English: Operating Frequency/Max Output Power
Polski: Częstotliwość pracy / Maksymalna moc wyjściowa
Deutsch: Betriebsfrequenz/Max. Ausgangsleistung
Русский: Рабочая частота/макс. вы³одная мощность
Français: Fréquence de fonctionnement/Puissance de sortie maximale
Nederlands: Bedrijfsfrequentie/Maximaal uitgangsvermogen
Čeština: Provozní frekvence/maximální výstupní výkon
Română: Frecvenţa de funcţionare/Puterea maximă de ieșire
Português: Frequência de Funcionamento/Potência Máxima de Saída
Svenska: Driftsfrekvens / Max Uteffekt
Slovenský: Prevádzková frekvencia/maximálny výstupný výkon
:  ¶  /  ƒ
·
Magyar: Működési frekvencia/Maximális kimeneti teljesítmény
Italiano: Frequenza operativa/Potenza di uscita massima
Български: Работна честота/максимална из³одна мощност
Español: Frecuencia operativa/Potencia de salida máxima
2412MHz-2472MHz/20dBm
5150MHz-5350MHz (indoor use only)/23dBm
5945MHz-6425MHz/23dBm (RX27 Pro/TX27 Pro)
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
FCC regulations restrict the operation of this device to indoor use only.
The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that
operation of this device is permitted in large aircraft while flying above 10,000 feet.
Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with
unmanned aircraft systems.
Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also
complies with Part 15 of the FCC RF Rules.
This equipment should be installed and operated with minimum distance 20cm between the device and
your body.
Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Operating frequency:
RX12/TX12/RX12 Pro/TX12 Pro: 2412-2462 MHz, 5150-5350 MHz, 5725-5825 MHz
RX27 Pro/TX27 Pro: 2412-2462 MHz, 5150-5350 MHz, 5725-5825 MHz, 5925-7125 MHz
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a
shielded RJ45 cable.
Dansk: Driftsfrekvens/Maks. Udgangseffekt
Suomi: Toimintataajuus/maksimilähtöteho
Hrvatski: Radna frekvencija/Maksimalna izlazna snaga
Latviešu: Operējošās frekvences/ Maksimālā jauda
Lietuvių: Darbinis dažnis / maksimali išėjimo galia
Slovenščina: Delovna frekvenca/Največja izhodna moč
Türkçe: Çalışma Frekansı/Maks. Çıkış Gücü
Polski-Uwaga: W państwach członkowskich UE, krajach Europejskiego Stowarzyszenia Wolnego Handlu (EFTA), Irlandii Północnej i Wielkiej Brytanii
praca w zakresie częstotliwości 5150MHz – 5350MHz (RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) i 5945 MHz – 6425 MHz
(RX27 Pro/TX27 Pro) jest dozwolona tylko w pomieszczeniach.
Deutsch-Achtung: In den EU-Mitgliedsstaaten, den EFTA-Ländern, Nordirland und Großbritannien ist der Betrieb im Frequenzbereich
5150MHz – 5350MHz (RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) und 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro) nur in Innenräumen
erlaubt.
Français-Attention: Dans les États membres de l’UE, les pays de l’AELE, l’Irlande du Nord et la Grande-Bretagne, l’utilisation dans la gamme de
fréquences 5150MHz – 5350MHz (RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) et 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro) n’est
autorisée qu’en intérieur.
Nederlands-Aandacht: In de EU-lidstaten, de EVA-landen, Noord-Ierland en Groot-Brittannië is gebruik in het 5150MHz – 5350MHz
(RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) en 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro) frequentiebereik alleen binnenshuis
toegestaan.
Čeština-Pozor: V členských státech EU, zemích ESVO, Severním Irsku a Velké Británii je provoz ve frekvenčním rozsahu 5150MHz – 5350MHz
(RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) a 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro) povolen pouze v interiéru.
Română-Atenţie: În statele membre UE, ţările EFTA, Irlanda de Nord și Marea Britanie, operarea în intervalul de frecvenţă 5150MHz – 5350MHz
(RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) și 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro) este permisă numai în interior.
Português-Atenção: Nos estados membros da UE, países da EFTA, Irlanda do Norte e Grã-Bretanha, o funcionamento na gama de frequências
5150MHz – 5350MHz (RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) e 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro) só é permitido no
interior.
Svenska-Uppmärksamhet: I EU medlemsstater, EFTA - länderna, Nordirland och Storbritannien är det endast tillåtet att använda frekvensområdet
5150MHz – 5350MHz (RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) MHz och 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro) inomhus.
Slovenský-Pozor: V členských štátoch EÚ, krajinách EFTA, Severnom Írsku a Veľkej Británii je prevádzka vo frekvenčnom pásme 5150MHz – 5350MHz
(RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) a 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro) povolená len v interiéri.
-: μ , ,   ,    ­€
€‚ 5150MHz – 5350MHz (RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) a 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro)
­ ­ μ ‚ƒ  .
Magyar-Figyelem: Az EU-tagállamokban, az EFTA-országokban, Észak-Írországban és Nagy-Britanniában az 5150MHz – 5350MHz
(RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) zés az 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro)-es frekvenciatartományban való
működtetés csak beltérben engedélyezett.
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This
means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled
or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer when he buys a
new electrical or electronic equipment.
AT BE BG CH CY CZ DE DK EE EL ES FI FR HR HU
IS
IT
LI
IE
LT LU LV MT NL NO PL PT RO SE SI SK UK(NI)
UK
• Check whether the WAN port of the router is connected to a modem or Ethernet jack
properly.
• Log in to the web UI of the router and navigate to the Internet Settings page. Follow
the instructions on the page to solve the problem.
If the problem persists, try the following solutions:
• For WiFi-enabled devices:
− Check whether your WiFi-enabled devices are connected to the WiFi network of
the router.
− Visit tendawifi.com to log in to the web UI and change your WiFi name and WiFi
password on the WiFi Settings page. Then try again.
• For wired devices:
− Check whether your wired devices are connected to a LAN port properly.
− Check whether wired devices are set to Obtain an IP address automatically and
Obtain DNS server address automatically.
Wall Mounting
This router can be installed on the wall with two screws. The recommended wall mounting
tools are as follows:
[Expansion bolt] Outer diameter: 6.0 mm; Length: 26.4 mm
[Screws] Thread diameter: 3 mm; Length: 14 mm; Head diameter: 5.2 mm
Get support and services
For technical specifications, user guides and more information, please visit the product page
or service page on www.tendacn.com. Multiple languages are available.
You can see the product name and model on the product label .
https://www.tendacn.com/service/default.html
Safety Precautions
Before performing an operation, read the operation instructions and precautions to be taken, and follow them
to prevent accidents. The warning and danger items in other documents do not cover all the safety
precautions that must be followed. They are only supplementary information, and the installation and
maintenance personnel need to understand the basic safety precautions to be taken.
- The device is for indoor usage only.
- For desktop mounting, the device must be horizontally mounted for safe use.
- If the device supports wall mounting, the device is only suitable for mounting at heights ≤ 2 m.
- Do not use the device in a place where wireless devices are not allowed.
- Please use the included power adapter.
- Mains plug is used as the disconnect device, and shall remain readily operable.
- The power socket shall be installed near the device and easily accessible.
- Operating environment: Temperature: 0℃ – 40℃; Humidity: (10% – 90%) RH, non-condensing;
Storage environment: Temperature: -40℃ to +70℃; Humidity: (5% – 90%) RH, non-condensing.
- Keep the device away from water, fire, high electric field, high magnetic field, and inflammable and
explosive items.
- Unplug this device and disconnect all cables during lightning storms or when the device is unused for long
periods.
- Do not use the power adapter if its plug or cord is damaged.
- If such phenomena as smoke, abnormal sound or smell appear when you use the device, immediately
stop using it and disconnect its power supply, unplug all connected cables, and contact the after-sales
service personnel.
- Disassembling or modifying the device or its accessories without authorization voids the warranty, and
might cause safety hazards.
- For latest safety precautions, see Safety and Regulatory Information on www.tendacom.cn.
Italiano-Attenzione: Negli Stati membri dell'UE, nei Paesi EFTA, nell'Irlanda del Nord e in Gran Bretagna, il funzionamento nella gamma di frequenze
5150MHz – 5350MHz (RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) e 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro) è consentito solo in
ambienti chiusi.
Български-Внимание: В страните-членки на ЕС, страните от ЕАСТ, Северна Ирландия и Великобритания, работата в честотния
диапазон 5150MHz – 5350MHz (RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) и 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro) е
разрешена само на закрито.
Español-Atención: En los estados miembros de la UE, los países de la AELC, Irlanda del Norte y Gran Bretaña, el rango de frecuencia operativa de
5150MHz – 5350MHz (RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) y 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro) solo está permitido en
interiores.
Eesti-Tähelepanu: EL-o liikmesriikides, EFTA riikides, Põhja-Iirimaal ja Suurbritannias on sagedusvahemikus 5150MHz – 5350MHz
(RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) ja 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro) kasutamine lubatud ainult siseruumides.
Dansk-Bemærk: I EU-medlemslandene, EFTA-landene, Nordirland og Storbritannien er drift i frekvensområdet 5150MHz – 5350MHz
(RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro)z og 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro) kun tilladt indendørs.
Suomi-Huom: Eu-maissa, EFTA-maissa sekä Isossa-Britanniassa ja Pohjois-Irlannissa taajuusaluetta 5150MHz – 5350MHz (RX12/TX12/
RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) ja 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro) on sallittua käyttää ainoastaan sisätiloissa.
Eesti: Töösagedus/Max väljundvõimsus
A5: Try the following solutions:
A4: Try the following solutions:
− Check whether your WiFi-enabled device supports 5 GHz or 6 GHz WiFi network. Only
devices supporting 5 GHz/6 GHz network can find and connect to the 5 GHz/6 GHz
WiFi network.
− Check whether you have enabled Unify 2.4 GHz & 5 GHz or Unify 2.4 GHz & 5 GHz
& 6 GHz on the WiFi Settings page. If it is enabled, disable it and try again.
English-Attention: In EU member states, EFTA countries, Northern Ireland and Great Britain, the operation in the frequency range 5150MHz – 5350MHz
(RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) and 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro) is only permitted indoors.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case
the user may be required to take adequate measures.
Q5: When I use the product as a router, I cannot access the internet after the
configuration. What should I do?
Hrvatski-Pozornost: U državama članicama EU, zemljama EFTA-e, Sjevernoj Irskoj i Velikoj Britaniji, rad u frekvencijskom rasponu od
5150MHz – 5350MHz (RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) i 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro) dopušten je samo u
zatvorenom prostoru.
Latviešu-Uzmanību: ES valstīs, EBTA valstīs, Ziemeļīrijā un Lielbritānijā, operēšana iekštelpās ir atļauta tikai 5150 MHz -5350 MHz un
5150MHz – 5350MHz (RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) ir 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro) diapazonā.
Lietuvių-Dėmesio: ES valstybėse narėse, ELPA šalyse, Šiaurės Airijoje ir Didžiojoje Britanijoje 5150MHz – 5350MHz (RX12/TX12/RX12 Pro/
TX12 Pro/RX27 Pro/TX27 Pro) in 5945 MHz – 6425 MHz dažnių diapazone leidžiama veikti tik patalpose.
Slovenščina-Pozor: V državah članicah EU, državah EFTA, Severni Irski in Veliki Britaniji je delovanje v frekvenčnem območju 5150MHz – 5350MHz
(RX12/TX12/RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) in 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro) dovoljeno samo v zaprtih prostorih.
Íslenska-Athugið: Í aðildarríkjum ESB, EFTA-löndum, Norður-Írlandi og Bretlandi er rekstur á tíðnisviðinu 5150MHz – 5350MHz (RX12/TX12/
RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) og 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro) aðeins leyfður innandyra.
Norsk-OBS: I EUs medlemsland, EFTA-land, Nord-Irland og Storbritannia er drift i frekvensområdet 5150MHz – 5350MHz (RX12/TX12/
RX12 Pro/TX12 Pro/RX27 Pro/TX27 Pro) in 5945 MHz – 6425 MHz (RX27 Pro/TX27 Pro) kun tillatt innendørs.
Technical Support
Shenzhen Tenda Technology Co., Ltd.
Floor 6-8, Tower E3, No.1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China.
518052
Website: www.tendacn.com
E-mail: [email protected]
[email protected] (United Kingdom)
[email protected] (North America)
Copyright
© 2023 Shenzhen Tenda Technology Co., Ltd. All rights reserved.
Tenda is a registered trademark legally held by Shenzhen Tenda Technology Co., Ltd. Other
brand and product names mentioned herein are trademarks or registered trademarks of their
respective holders. Specifications are subject to change without notice.
V2.0 Keep for future reference.
">