Smart Watch User Manual
Precautions before use:
1. The company reserves the right to modify the contents of this
manual without any notice. Some functions are different in specific
software versions, which is normal.
2. Please charge the product for more than 2 hours before use. Please
use a charger with a specification of 5V, 1A. This product does not
support fast charging. Charging with water (sweat) is prohibited to
prevent short circuit and product damage.
3. Before using the product, please download and connect the APP
on the mobile phone. Connect the APP to synchronize the watch time
and set personal information. For details, see the instructions for the
subsequent synchronization software.
1： Product Overview
It is recommended to use the mobile phone model version (too low
version may cause connection problems):
Android mobile phone: support operating system version 5.0 or
above;
Apple mobile phone: support operating system version 9.0 and
above;
2： APP download and APP connection method
1.Scan the QR code below to download the APP
software.
Use the browser to scan the QR code below or
(GloryFit downloads
download the QR code from the watch settings.
QR code)
During the download and installation process,
please give the corresponding permission to this
software to ensure the normal Bluetooth connection.
The APP software name is GloryFit.
GloryFit application
Special attention:
1. If you haven't used the APP for a long time (12 hours or more),
the APP will be cleaned up by the phone's own IOS system. At this
time, the APP application and the watch are disconnected, and the
GloryFit application function will not be used. If you turn on the
push function, the push function can be used normally. Open the
APP application again, and the watch will be automatically
reconnected.
2. After installing the APP software on Android phones, you need
to open the background application startup permission in the phone
settings. Different models of phones will have differences.
1.APP application and watch connection method:
1. Open the downloaded APP and select "Email" or "Third Party
Login" (as shown in Figure 1).
2. After logging in successfully, click "Select Watch" (as shown in
Figure 2) to enter the "Add Device" interface, and click to select the
Bluetooth name of the device you purchased (as shown in Figure 3)
to connect successfully.
(Figure 1)
(Figure 2)
(Figure 3)
The watch can be paired with the mobile app in the app.
Note: For the IOS system, you need to enter: Settings - Bluetooth,
ignore Bluetooth pairing, and completely unbind.
3： Main functions of smart watch
1 Basic operation
1.1Power on: When the watch is off, press and hold the key on the
watch side for 3 seconds to start up; In standby mode, briefly press
the side button or single point screen to wake up the watch.
1.2 Shutdown: When the watch is on, press and hold the side button
for 3 seconds or select shutdown in the setting to enter the switch
selection interface and select“ ×” Exit the shutdown interface and
select "√" to shut down directly.
1.3 The watch interface switching operation is shown below:
1. Slide the dial interface from top to bottom to enter the status bar
interface
2. Slide the dial interface from right to left to enter the shortcut
function interface
3. Slide the dial interface from left to right to enter the menu interface
4. Slide the dial interface from bottom to top to enter the message
notification interface
Dial operation interface
Status bar interface
1.4 The status bar interface displays the functions of mobile phone
search, brightness adjustment, about, setting, connection status, and
power display.
2. Dial switch
Press and hold the screen for 2 seconds in the dial interface to enter
the switch interface, slide the screen left and right to switch the dial,
and select the dial with a single point.
3. Status
The step counting function is enabled by default after the device is
powered on, and the step counting data and heat of the day are
displayed in real time. After the watch is successfully paired with
the APP, the motion data will be automatically synchronized (or
manually refreshed) and uploaded to the APP, including the steps,
distance, calories and other parameters.
4. Sports
2.4.1 Sports modes include: outdoor running, cycling, rope skipping,
swimming, badminton, etc., totaling 114 kinds.
Note: The motion data will not be saved to the APP terminal, but
can only be viewed on the watch terminal.
5. Sleep monitoring
The default sleep monitoring time of the watch is from
18:00 to 12:00 the next day. If you wear a watch to
sleep, the watch will automatically judge whether you
enter the sleep monitoring mode, automatically detect
your sleep quality of deep sleep/light sleep/awake all
night, and calculate your sleep duration; Sleep data currently
only supports APP viewing.
6. Heart rate, blood pressure, blood oxygen (healthy)
The heart rate, blood pressure and blood oxygen values can be
independently detected through the watch, and the values can be
synchronized to the APP terminal (please measure in a quiet state)
7. Notice (information)
After successfully pairing with the phone, you need
to turn on the APP reminder function, and the
information received in the phone status bar will be
synchronized to the watch
8. Bluetooth music
After connecting the phone, you can play the music
in the phone through the watch, and you can play,
pause, and switch the previous song to the next.
9.Weather
The weather interface will display the current weather.
The weather information needs to be connected to the
APP to obtain data. If the connection is disconnected
for a long time, the weather information will not be
updated.
10.Settings
14.1 Click Settings to enter the setting interface. The setting
interface has options such as dial theme, language setting, power
off, APP downloading QR code, and factory restoration.
14.2 Shutdown: click to enter the shutdown selection interface, and
select“ ×” Exit the shutdown interface and select "√" to shut down
directly.
14.3 APP download QR code: click to enter the QR code, and use
the mobile phone scanning tool to scan the QR code to download.
14.4 Factory recovery: click to enter the factory recovery selection
interface, and select“ ×” Exit the factory recovery interface, select
"√" to directly restore the factory, and all data at the watch end will
be cleared.
14.5 About: display the hand device name, Bluetooth address and
version.
4： Common faults and troubleshooting
4.1 The watch cannot be turned on
4.1.1 The time of pressing the power-on key may be too short.
Please press and hold the power-on key for more than 3 seconds.
4.1.2 The battery may be too low. Please charge it in time.
4.1.3 The battery may enter the low battery protection, and the
ordinary charger will not respond to charging. Please try to use the
charger with an output power of 5V/1V to charge and activate.
4.2 The watch will shut down automatically
The battery may be too low. Please charge it.
">
