English Installation Manual of WHIRLPOOL KEMS307GBS2

27” and 30” Electric

Built-in Microwauel

Oven Combination

Quick Reference

Table of Contents:

Pages cl 1 Product dimensions

0 1 Cutout dimensions q q

Electrical requirements

[q 131 Installation steps

If

you need assistance:

Check your Use and Care Guide for a toll-free number to call or call the dealer from whom you purchased this appliance. The dealer is listed in the Yellow Pages of your phone directory under

“Appliances - Household - Major-Service and Repair.”

Call when you:

LJ Have questions about built-in oven installation or operation. q Need to obtain the name and number of an authorized service company.

When you call, you will need: q The built-in oven model number.

Q The built-in oven serial number.

Both numbers are listed on the model/serial rating plate, located on the microwave oven frame.

Page 1

D cabinet

41” recessed height

23” max.

1 recessed depth \

27” oven

25-316 recessed

1” top of cutout to bottom of upper cabinet door

A

-T

41-l 14” cutout height v

25-l/2” cutout 4 width

L

-3 l-112” min. bottom of cutout to top of cabmet

27” oven

T

19-l 14” lottom of

:utout to floor i

_ 23-114” min. cutout depth -

* 23” recessed - oven depth

*

* recessed oven oven

- front

:

42-7116” overall height

41” recessed height

\ h

23” max. recessed

I depth \

1

-T l;~~~,mi;~ cutout to top of cabinet

-

30” oven

26-3/W t

41-l/4” cutout height k

28-w cutout width b

30” oven

-

7

19-l/4” bottom

,f cutout to floor

1” top of cutout to bottom of upper cabinet door

_L

7 overall

!

42.7116” height

Important: Observe all governing codes and ordinances.

Proper installation is your responsibility.

Have a qualified technician install this oven.

Oven location should be away from strong draft areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance.

Recessed installation area must provide complete enclosure around the recessed portion of the oven.

Electrical ground is required. See “Electrical requirements.”

Electrical supply junction box should be located

3 inches maximum below the support surface when oven is installed in a wall cabinet. Cutout for wiring should be in the right rear or left rear corner. For undercounter installation, it is recommended that the junction box be located in the adjacent right or left cabinet. If installing junction box on rear wall behind oven, junction box must be recessed and located in the upper or lower right or left corner of cabinet.

Oven support surface MUST be solid, level and flush with bottom of cabinet cutout.

Excessive Microwave Energy Exposure

Do Not attempt to operate the microwave oven with the door open.

Do Not tamper with or defeat the safety interlocks.

Do Not place objects between the microwave oven front face and door.

Do Not allow soil or cleaner residue to accumulate on sealing surface of the microwave oven door.

Do Not operate the microwave oven if damaged.

Do Not operate the microwave oven if:

- door is bent.

- hinges and latches are broken or loose.

- door seals, sealing surfaces or glass are broken.

The microwave oven door must close properly to provide safe operation.

Have a qualified repair person adjust, repair and check microwave oven for microwave leakage after a repair is made.

Do Not use microwave for commercial purposes. The microwave oven in this unit is designed for household use only.

Failure to follow these instructions could result in exposure to excessive microwave energy.

It is the customer’s responsibility:

To contact a qualified electrical installer.

To assure that the electrical installation is adequate and in conformance with National

Electrical Code, ANSVNFPA 70 - latest edition*, and all local codes and ordinances.

Copies of the standards listed may be obtained from: l

National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

Cabinet filler kits are available from your dealer.

Use a matching color kit if oven is smaller than your cabinet opening.

27” oven filler height is 7-13/W

Black - 4378950

White - 4378951

Almond - 4378952

30” oven filler height is 4-13/W

Black - 4378944

White - 4378945

Almond - 4378946

Tool needed:

Phillips screwdriver

Parts supplied:

rews

Cabinet side view

Electrical Shock Hazard

Electrically ground oven.

Connect ground with lo-gauge-minimum solid copper wire.

Failure to follow these instructions could result in death, fire or electrical shock.

If codes permit and a separate grounding wire is used, it is recommended that a qualified electrician determine that the grounding path and wire gauge are in accordance with local codes.

Do Not ground to a gas pipe.

Check with a qualified electrician if you are not sure oven is properly grounded.

Do Not have a fuse in the neutral or grounding circuit.

Oven must be connected to the proper electrical voltage and frequency as specified on the model/serial rating plate. (The model/serial rating plate is located on the oven door or on the oven frame.) q

CONNECT WITH COPPER WIRE ONLY. q Models rated from 7.3 to 9.6 kW at 240 volts

(5.5 to 7.2 kW at 208 volts) require a separate

40-ampere circuit. Models rated at 7.2 kW and below at 240 volts (5.4 kW and below at 208 volts) require a separate 30-ampere circuit. q A time-delay fuse or circuit breaker is recommended. q

Connect directly to the fused disconnect (or circuit breaker box) through flexible, armored or non-metallic sheathed, copper cable (with grounding wire). q

Flexible armored cable from appliance should be connected directly to junction box.

VJ Fuse both sides of the line. q

A U.L.-listed conduit connector must be provided at the junction box. q Do Not cut the conduit.

Wire sizes and connections must conform with the rating of the appliance and to the requirements of the National Electrical Code,

ANSI/NFPA 70 -latest edition (*, See Page I) and all local codes and ordinances.

Q Grasp oven to lift oven. frame q oven microwave and oven operation. q Use screws to attach oven to cabinet.

Excessive Weight Hazard

Use two or more people to move and install oven.

Failure to follow this instruction can result in back or other injury.

Important: Use both hands to remove oven doors.

Do Not use handle or any portion of the tont frame or trim for lifting.

Before moving oven across floor, check that oven is on shipping base or slide oven onto cardboard or hardboard.

Do Not remove shipping feet at the front lower corners of oven. q RemoJe side trim pieces.

Page 2

Do hot remove shipping feet. l l

1 n

Turn power supply off. Move oven close to final position.

Remove and discard shipping materials, tape and protective film from the oven. Do

Not remove shipping base or shipping feet at the front lower corners of oven. The shipping feet will protect the lower oven trim until oven is inserted into cabinet,

Remove and set aside racks and other parts from inside oven.

Insert small of pin

Remove trim screw.

2 n

Completely open lower oven door. Insert small end of a door removal pin into each door hinge. Grasp door handle from the bottom and gently close door as far as it will shut. Lift slightly and grasp bottom of door with other hand. Pull door out at bottom to remove. Set door aside on protected surface.

3

1

3 n

Remove trir&crews attaching right and left side trim to oven. Grasp the bottom end of trim and pull away from oven. Slide top end of trim downward to remove trim from oven. Take care not to scratch other surfaces with ends of trim. Set trim and screws aside on protected surface.

iunction cable from power supply iunction cable from power supply

Electrical Shock Hazard

Disconnect power to the junction box before making connection.

Electrically ground oven.

Connect ground with lo-gauge-minimum solid copper wire.

Failure to follow these instructions could result in death, fire or electrical shock.

This oven is manufactured with white (neutral) power supply wire and a cabinet-connected bare grounding wire twisted together.

4 Feed oven cable through opening in

. the cabinet. Make electrical connection following the steps needed for your installation.

1. Disconnect the power supply.

2. Remove the junction box cover.

3. Connect oven cable to junction box through the

U.L.-listed conduit connector.

4. Connect the two black wires together with twist-on connectors.

5. Connect the two red wires together with twist-on connectors.

6. Complete electrical connection according to local codes and ordinances. white e&be= grounding oven cable wires - iectorv crimped

Fig&e 1

WI

K-listed cable from oven

I

conduit connector

If local codes PERMIT

:onnecting cabinet-groundins conductor to neutral white wire in junction box:

r. Connect the factory-crimped bare and white oven cable wires to the neutral (white) wire in junction box. See Figure 1.

I. Replace junction box cover.

Figure 2

*es bqre grounding T wires k4 ‘U.L.-listed conduit cable from connector oven

If local codes DO NOT PERMIT connecting cabinet-grounding conductor to neutral white wire in junction box:

If connecting to a four-wire electrical system:

7. Separate the factory-crimped bare and white oven cable wires.

8. Connect white oven cable wire to neutral (white) wire in junction box. See Figure 2.

9. Connect the bare grounding oven cable wire to a grounded wire in the junction box. See

Figure 2.

IO. Replace junction box cover.

7. Separate bare and white oven cable wires.

8. Connect white oven cable wire to neutral (white) wire in junction box. See Figure 2.

9. Connect the bare grounding over cable wire to the green groundin: wire in junction box. Do Not connect bare grounding wire to neutral (white) wire in junction box. See Figure 2.

10. Replace junction box cover.

H

Attachment

Carefully push against seal area of oven front frame when pushing oven into cabinet.

Do Not push against outside edges.

8 n

Replace oven racks. oven framl screws

5 n

Lift oven into cabinet cutout using the oven opening as an area to grip. -

- b w Important: Securely fasten oven to cabinet using the screws provided (two screws for a single oven or four screws for a double oven). Insert the screws through holes in mounting rails. Do Not over-tighten screws.

5

3

’ Push trim into place.

Replace tym screw

9 n

Replace the lower oven door by inserting ends of hinges into hinge slots in oven frame. Push behind each hinge so that hinges are pushed into oven frame as far as they will go. Open door and remove both door removal pins. Close and open door to check that door closes and opens completely. If door does not close or open completely, you have not pushed hinges completely into frame. Repeat door removal step and reinsert door into hinge slots again.

Push against seal area of front frame to push oven into cabinet until shipping feet almost contact cabinet. Use a Phillips screwdriver to remove screws attaching shipping feet. Remove and discard shipping feet.

Push oven completely into cabinet and center oven in cabinet cutout.

10 w Turn on power supply. The display panel will light up briefly. “PF” should appear in the temperature display.

(-1 (-1 (-1 n

Check the operation of your lower oven. Press the “BROIL” pad. “BROIL” will appear in the display. Press the “START” pad.

L

Page 3

7 n

Slide top end of each trim upward onto oven side rails. Push each trim into place at bottom of trim. Use screws to attach each trim to oven. Take care not to scratch other surfaces with ends of trim.

Make sure the oven door is closed and the “ON” light is shown in the display area. After 2 minutes, partially open oven door. You should feel heat from the oven. Press the “CANCEL” pad.

If your oven does not heat or an”F” appears in the display, contact your dealer or check the “If you need service...” section of this Installation

Instructions.

1

2 . Check the operation of the l minutes.

Press the “START/ENTER” pad. The interior microwave oven light should be on and the remaining cooking time should be displayed. l l l l

When display reads “l:OO,” open microwave oven door. The microwave should stop cooking.

Close door firmly. The interior microwave oven light should turn off.

. Press the “START/ENTER” pad. Microwave oven should begin cooking and the microwave oven interior light should be on.

Let microwave oven complete cooking time. A tone will sound four times at end of cooking time and microwave oven will shut off.

Ooen microwave oven door and carefullv remove container. Water in container should be hot.

To

get the most efficient use

from your new oven, read your

Use and Care Guide. Keep

Installation Instructions and Guide close to oven for easy reference.

If oven does not operate:

Q Check that circuit breaker is not tripped or house fuse blown. q See Use and Care Guide for troubleshooting list.

If you need assistance:

If you have questions about operating, cleaning or maintaining your oven: q Refer to Use and Care Guide.

0 Call the Consumer Assistance Center: Check your Use and Care Guide for a toll-free number to call or call the dealer from whom you purchased this appliance. The dealer is listed in the Yellow Pages of your phone directory under

“Appliances - Household - Major-Service and Repair.”

If you need service:

Maintain the quality built into your built-in oven by calling an authorized service company.

To obtain the name and number of an authorized service company: q

Contact the dealer from whom you purchased your built-in oven; or q Look in the Yellow Pages of your telephone directory under “Appliances - Household -

Major - Service and Repair” for an authorized service company; or q Call the Consumer Assistance Center. The toll- free number is listed in your Use and Care Guide.

When you call, you will need: q The built-in oven model number. l7J The built-in oven serial number.

Both numbers are listed on the model/serial rating plate, located on the microwave oven frame.

Part No. 4450412 Rev. A

0 1996 Printed in U.S.A.