Cree Lighting Styllus Linear Surface Mount Installation Guide

Styllus Linear TM Series
LED Ambient Luminaire with Emergency Driver
Ceiling/Surface Mount
IMPORTANT SAFEGUARDS
INSTALLATION INSTRUCTIONS
INSTRUCTIONS D’INSTALLATION
When using electrical equipment, basic safety precautions should always be
followed including the following:
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS
1.
DANGER- Risk of shock- Disconnect power before installation.
DANGER – Risque de choc – Couper l’alimentation avant
l’installation.
2. This luminaire must be installed in accordance with the NEC or
your local electrical code. If you are not familiar with these codes
and requirements, consult a qualified electrician.
Installation Instructions are divided into
Ce produit doit être installé conformément à NEC ou votre code
7 sections:
électrique local. Si vous n’êtes pas familier avec ces codes et ces
exigences, veuillez contacter un électricien qualifié.
1. Surface Mounting - Individual Luminaire
3. To reduce the risk of electric shock, disconnect both standard
2. Surface Mounting - Continuous Row
and emergency power supplies and converter connector of the
3. SmartCast Option
emergency driver before servicing.
4. Styllus with Lutron Vive RF Sensor Option
Pour réduire le risque de décharge électrique, vous devez
déconnecter à la fois le disjoncteur divisionnaire ou les fusibles et
5. Styllus with Wall Wash Optic Option
les alimentations d’urgence avant l’entretien.
6. Emergency Driver Check
4. Do not use outdoors.
7. Electrical Connections
Ne pas utiliser à l’extérieur.
5. Do not let power supply cords touch hot surfaces.
Ne laissez pas les cordons d’alimentation toucher les surfaces chaudes.
6. Do not mount near gas or electric heaters.
Ne montez PAS près des appareils de chauffage de gaz ou électriques.
7. Do Not use this equipment for other than its intended use.
NE PAS utiliser cet équipement à d’autres fins que celle qui est prévue
8. Equipment should be mounted in locations and heights where it will not readily be subjected to tampering by unauthorized
personnel.
L’équipement doit être monté dans des endroits et à des hauteurs où il ne sera pas soumis à des altérations par des personnes
non autorisées.
9. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
L’utilisation d’accessoires non recommandés par le fabricant peut causer une situation dangereuse.
10. SUITABLE FOR CONTINUOUS ROW MOUNTING.
PEUT ÊTRE MONTÉ EN RANGÉE CONTINUE.
11. Make sure the equipment is properly grounded.
12. Always de-energize the circuit and/or equipment before connecting to, disconnecting from or servicing the equipment
SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE
NOTES:
• CAUTION - It is the installers responsibility to ensure
that ceiling is structurally capable of supporting the
weight of luminaire/luminaire row.
• Endcap kits and joining hardware are packaged
separately for continuous rows.
• To Prevent Luminaire Row From Over-Current: By
adding the input current of each luminaire section
marked on the luminaire, the total current per power
feed must not exceed the maximum line wire amperage
rating in the luminaire and the power feed cord/wire
amperage rating whichever is least.
1 of 7
ST3-SF
LPN00644X0014A0_E
TO INSTALL:
1
Chalk Line
LED Reflector
Tray
Fasteners
(Supplied By Others)
Lens
Fasteners
2
Extrusion
Lens
Slide Plastic Card
or Putty Knife Here
SECTION 1:
SURFACE MOUNTING-INDIVIDUAL LUMINAIRE
CAUTION: Luminaires should be secured
to structure above to support weight of
luminaire.
harness. Set lens and LED Reflector tray
aside. See Figure 1.
STEP 1:
Use the luminaire as a template to locate the
mounting holes by centering luminaire over
recessed switch box. Keep the switch box square
to and on center lengthwise, mark each mounting
anchors hole location, See Figure 2. Ensure that
all mounting points are on the same center line
as the switch box installed. Drill appropriate holes
for mounting surface and fasteners to be used.
Securely attach housing to ceiling: See Figure 1.
Remove lens and LED/reflector tray and set
aside in order of run placement for reinstalling
later. To remove lens, carefully slide a plastic
card or putty knife between the lens and
extrusion towards the end of the luminaire.
Using the plastic card or putty knife, push the
lens inward until the lens comes free. See
Figure 1 and 2.
STEP 2:
After removing the lens, remove the Phillips
head reflector screws, remove the LED
Reflector Tray, and disconnect the LED
2 of 7
STEP 3:
STEP 4:
Using the 1.5” diameter hole located in the
center of the luminaire, route the electrical
leads out into customer supplied junction box
and make electrical connections per Section 3
“Electrical Connections”.
STEP 5:
Reconnect LED harness. Replace LED trays
and lens that was removed in Step 1 & 2
above, ensure that no wires are pinched.
NOTE: Pre-drilled diameter 5/8" mounting
anchor holes are located 2.13" from the end
of each luminaire. See Figure 3 on the next
page.
LPN00644X0014A0_E
3
LUMINAIRE ROW LAYOUT: SINGLE UNIT 2' - 12'
2’ FIXTURE
24.25"
0.13" Endcap
Thickness
0.13"
4’ FIXTURE
48.25"
0.13" Endcap
Thickness
0.13" Endcap
Thickness
6’ FIXTURE
72.25"
0.13" Endcap
Thickness
0.13" Endcap
Thickness
8’ FIXTURE
96.25"
0.13" Endcap
Thickness
0.13" Endcap
Thickness
10’ FIXTURE
120.25"
0.13" Endcap
Thickness
0.13" Endcap
Thickness
12’ FIXTURE
144.25"
0.13" Endcap
Thickness
0.13" Endcap
Thickness
***NOTE: Plugged holes provided for feed wire in the center of each luminaire.
2”
5/8" Mounting Anchor Holes
1 1/2" Plugged Hole For Feed Wire
5/8" Mounting Anchor Holes
3 of 7
LPN00644X0014A0_E
5/8" Mounting Hole
4
End Plate Cap (With
Alignment Pins)
5
Male End
Female Joiner Bracket
Female End
Slide Screw w/
Lock Nuts
End-Plate
Lock Nuts
Alignment Pins
6
Chalk Line
Female End
Male End
Second Luminaire
First Luminaire
SECTION 2: SURFACE MOUNTING - CONTINUOUS ROW MOUNTING
CAUTION: Ceiling contractor must provide
appropriate anchors to support weight of ceiling
mount linear luminaires.
CAUTION: Do not attempt to assemble
luminaire rows on the ground and then lift
into position. This may create stress at the
connection points and may result in damage
and/or mechanical failure.
CAUTION: Do not connect power in a run until
all of run is installed, wire harnesses connected,
and luminaire joints completed.
STEP 1:
From center line of lengthwise mounted switch
box(es), snap a lengthwise chalk line on ceiling
to the right of Junction box approximately the
full length of the row to be installed.
STEP 2:
Remove lens and upper LED/reflector tray
and set aside in order of run placement for
reinstalling later. To remove lens, carefully slide
a plastic card or putty knife between the lens
and extrusion towards the end of the luminaire.
Using the plastic card or putty knife, push the
4 of 7
lens inward until the lens come free. After
removing the lens, remove the Philips head
reflector screws, remove the LED Reflector Tray,
and disconnect the LED harness. Set lens and
LED Reflector tray aside. See Figure 1 and 2.
STEP 3:
Locate and install End Cap Kits. In order to install
the end cap on the male end of the luminaire,
replace the male joiner bracket with the female
joiner bracket and remove the alignment pins.
See Figure 4 and 6.
STEP 4:
Attach the first luminaire Right-Hand End of
the Row onto the ceiling per Figure 6. Tighten
mounting screws on luminaire snug as not to
allow luminaire to move when being aligned
with the next luminaire in the row.
STEP 5:
Position second luminaire in row such that it aligns
with joint end (male end) of first luminaire. Attach
using customer supplied hardware to structure
above. Connect the second luminaire to the first
luminaire as shown in Figure 5 and 6. Plug wire
harness together and push excess wire into
luminaire wiring chamber, ensure that wires are
not pinched.
STEP 6:
Push luminaires tightly together while making
sure the alignment pins slide into the interior
tracks of each luminaire and span the luminaire
joint. Secure joint by tightening supplied keps
locknuts on threaded studs of male joiner
bracket. Figure 5 and 6.
STEP 7:
Continue to install and assemble row following
steps 1-6 above. Locate and install Junction box
to be centered on the End unit (Left-Hand End of
Run) luminaire, make electrical connections per
Section 5 “Electrical Connections”.
STEP 7:
Replace LED trays and lens that was removed in
Step 1 above, ensure that no wires are pinched.
LPN00644X0014A0_E
LUMINAIRE ROW LAYOUT: EXAMPLE OF A TWO AND THREE UNIT
16', 20' - 24' (CAN BE MOUNTED IN OTHER CONFIGURATIONS)
7
16’ FIXTURE
192-1/4" End Cap to End Cap
96 -1/8"
96 -1/8”
8’ UNIT
8’ UNIT
92” Mounting Center
92” Mounting Center
20’ FIXTURE
240-1/4" End Cap to End Cap
96 -1/8"
96 -1/8"
8’ UNIT
48-1/8""
8’ UNIT
92” Mounting Center
4’ UNIT
92” Mounting Center
44” Mounting Center
24’ FIXTURE
288-1/4" End Cap to End Cap
96 -1/8"
96 -1/8"
8’ UNIT
96 -1/8"
8’ UNIT
92” Mounting Center
8’ UNIT
92” Mounting Center
92” Mounting Center
EXAMPLE 3 FIXTURE CONTINUOUS ROW
FEED LOCATION
***NOTE: Plugged holes provided for feed wire in the
center of each luminaire.
Feet
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
5 of 7
4'
1
1
Units
6'
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
8'
1
2
1
2
2
3
2
3
3
4
3
4
4
5
4
5
5
6
5
6
6
7
6
7
7
8
7
8
8
9
End Cap
Kits
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Total Row Length (in) Endcap To Endcap
168.25
192.25
216.25
240.25
264.25
288.25
312.25
336.25
360.25
384.25
408.25
432.25
456.25
480.25
504.25
528.25
552.25
576.25
600.25
624.25
648.25
672.25
696.25
720.25
744.25
768.25
792.25
816.25
840.25
864.25
LPN00644X0014A0_E
PIR
8
9
Reset Button
Wall
LED
ALS/ Blue
Status LED
SECTION 3: SMARTCAST
COMMISSIONING
NOTE: Cree Lighting recommends reviewing
the Cree Lighting SmartCast Technology
Wireless Deployment Guide prior to installing
luminaires with Cree Lighting SmartCast
Technology.
NOTE:
• Visit Cree Lighting’s website for the
guide:
https://cree.widen.net/s/pplfkqkrwt/
smartcastr-wireless-deployment-guide
NOTE: SmartCast luminaires must be
installed on unswitched AC power. Constant
power is required to maintain all luminaires
on the SmartCast network. If wall control or
manual dimming is required, a SmartCast wall
control dimmer must be used for manual on,
off, and dimming.
NOTE: Before beginning fixture installation or
OneButton Setup, it is important to consider
the use of spaces and what luminaires will be
grouped together. Cree Lighting recommends
turning on AC power to luminaires that should
be grouped together and then initiating
the OneButton Setup while the remaining
luminaires are switched off of AC power. It
is recommended to commission one group
first and then turn AC power on to the second
group and continue until all luminaries are
commissioned.
NOTE: Continuous rows with SmartCast ship
with a dedicated sensor per fixture except
for corners. Corners ship with accessible
dimming leads that need to be wired into
the adjacent luminaire so that the corner
luminaire is controlled by the sensor of
the adjacent runner. Locate dimming leads
between adjacent fixture driver and sensor.
Connect corner dim leads into adjacent
dimming leads.
RESET RF MODULE
NOTE: For the Blue Status LED location see
Figure 8.
STEP 2:
Release for 1 sec.
STEP 3:
Press/Hold RESET button for 0.5 sec. Light
will turn off for a few seconds then go to full
bright and the Blue Status LED should begin a
2 blink sequence. Figure 8.
TROUBLESHOOTING:
Out of the box, if the light does not turn on
when power is applied:
•
•
•
•
•
Check Wiring with power off
If wired correctly, check to see if Blue
Status LED blinking on the RF Module.
If Blue Status LED is blinking, then
perform a RESET
(See RESET RF MODULE section).
If Blue Status LED is on solid or off,
call Cree Lighting Customer Service.
If you have done a RESET, and the light
is still off, call Cree Lighting Customer
Service.
If light is unresponsive, use Cree Lighting
Configuration Tool to verify configuration.
SECTION 4: STYLLUS WITH LUTRON
VIVE RF SENSOR OPTION
NOTE: Fixtures ordered with Vive are provided
with a factory installed, integrated Lutron Vive
wireless fixture control with occupancy and
daylight sensor.
NOTE: For set-up, programming, and
troubleshooting with a Vive system, please
refer to the installation instructions included
with the Vive hub or at www.lutron.com
DEFAULT FUNCTIONALITY FIXTURE
CONTROL SETTINGS:
• Auto On level: DFCSJ-OEM-OCC only
• Varies with ambient light level when
occupancy is triggered
( e.g., 100% for a dark room, 10% for a
bright room).
• Time-out period: 15 minutes
STEP 1:
Actuate RESET button through the access
hole using a paper clip. Push and hold until
Blue Status LED, begins blinking rapidly
(approximately 6-7 seconds). See Figure 8.
SECTION 5: STYLLUS WITH WALL
WASH OPTIC OPTION
LEDs are facing the wall. The wall wash optic
was designed for optimal performance when
mounted 24” from the wall. See Figure 9.
STEP 2:
The Wall Wash lens is shipped already
removed from the reflector. After installing the
product, unwrap and install the lens. The lens
must be installed with the texture side of the
lens facing the ground. The lens is installed
by angling into the reflector and then laid to
rest on the reflector ledges. The lens is held in
place by gravity.
SECTION 6: EMERGENCY DRIVER
CHECK
NOTE: For short-term testing of the
emergency function, the battery must be
charged for at least one hour. The emergency
driver must be charged for at least 24 hours
before conducting a long-term test.
STEP 1:
When AC power is applied, the charging
indicator light is illuminated, indicating the
battery is being charged. When power fails,
the emergency driver automatically switches
to emergency power, operating the LED array.
When AC power is restored, the emergency
driver returns to the charging mode.
STEP 2:
Although no routine maintenance is required
to keep the emergency driver functional, it
should be checked periodically to ensure
that it is working. The following schedule is
recommended:
• Visually inspect the charging indicator
light monthly. It should be illuminated.
• Test the emergency operation of
the fixture at 30-day intervals for a
minimum of 30 seconds. When the test
switch is depressed, the LED array
should operate.
• Conduct a 90-minute discharge test
once a year. The LED array should
operate for at least 90 minutes.
If the luminaire fails any of these checks,
consult service personnel.
REFER ANY SERVICING INDICATED BY
THESE CHECKS TO QUALIFIED PERSONNEL
EMERGENCY DRIVER AND AC DRIVER MUST
BE FED FROM THE SAME BRANCH CIRCUIT.
STEP 1:
Wall Wash optic must be oriented so the
6 of 7
LPN00644X0014A0_E
FCC NOTICE
To comply with the FCC RF exposure
compliance requirements, this device and its
antenna must not be co-located or operating
to conjunction with any other antenna or
transmitter.
This equipment should be installed and
operated with minimum distance 5cm
between the radiator & your body.
FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not
expressly approved could void your authority
to use this equipment.
This device complies with Part 15 of the
FCC Rules. Operation to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation
This device has been tested and found to
comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference when the device is operated
in a commercial environment. This device
generates, uses, and can radiate radio
frequency energy and, if not installed and
used in accordance with the instruction
manual, may cause harmful interference
to radio communications. Operation of this
device in a residential area is likely to cause
harmful interference in which case the user
will be required to correct the interference at
his own expense.
CAN ICES-005 (A)/NMB-005 (A)
The LED in the front of this device operates
within Risk Group 1 levels per IEC 62471.
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation
is subject to the following two conditions: (1)
this device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause
undesired operation of the device. In addition,
this device complies with ICES-005 of the
Industry Canada (IC) Regulations.
Le présent appareil est conforme aux CNR
d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1)
l’appareil ne doit pas produire de brouillage,
et (2) l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en
compromettre le fonctionnement.
INDUSTRY CANADA STATEMENT
SECTION 7:
ELECTRICAL CONNECTIONS
STEP 1:
For 120/277V applications make the following Electrical Connections:
a. Connect the black luminaire lead to the
unswitched voltage supply lead.
b. Connect the red luminaire lead to the
switched supply switched.
c. Connect the white luminaire lead to the neutral supply lead.
d. Connect the green or green/yellow ground
lead to the green supply lead.
a. Connect unswitched Hot 1 supply lead to the black lead.
b. Connect Hot 2 supply lead to the white lead
c. Connect the red luminaire lead to the
switched supply switched.
d. Connect the green or green/yellow ground lead to the supply
ground lead.
CORD/ SUPPLY WIRING
For 208/240V applications, make the following Electrical Connections:
LUMINAIRE
STEP 2:
a. If Dimming is an option; connect the violet dimming positive
lead to the supply dimming positive lead. If dimming is not
being used, ensure to cap off the violet lead.
GREEN
GROUND-GREEN
NEUTRAL OR HOT 2
NEUTRAL-WHITE
SWITCHED HOT
RED
UNSWITCHED HOT
BLACK
DIM (+) VIOLET
VIOLET
DIM (-) GREY
OR PINK
GREY
OR PINK
b. If Dimming is an option; connect the grey or pink dimming
negative lead to the supply dimming negative lead. If
dimming is not being used, ensure to cap off the grey or pink
lead.
STEP 3:
** NOTE: DO NOT mate leads until installation is complete and AC
power is supplied.
a. Locate the battery harness from the battery pack and
connect it to the receptacle on the emergency driver.
© 2021 Cree Lighting, A company of IDEAL INDUSTRIES. All rights reserved. For informational purposes only. Content is
subject to change. See www.creelighting.com/warranty for warranty and specifications. Cree® and the Cree Lighting logo are
registered trademarks of Cree, Inc. Styllus Linear™ and the Styllus Linear logo are trademarks of Cree Lighting, A company
of IDEAL INDUSTRIES.
www.creelighting.com
7 of 7
LPN00644X0014A0_E
">