Cree Lighting Styllus Linear Recessed Mount Installation Guide

Styllus Linear

TM

Series

LED Ambient Luminaire with Emergency Driver

Recessed Mount

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including the following:

READ AND FOLLOW ALL

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION

SAFETY INSTRUCTIONS

1. DANGER - Risk of shock- Disconnect power before installation.

DANGER – Risque de choc – Couper l’alimentation avant l’installation.

2. This luminaire must be installed in accordance with the NEC or your local electrical code. If you are not familiar with these codes and requirements, consult a qualified electrician.

Ce produit doit être installé conformément à NEC ou votre code

électrique local. Si vous n’êtes pas familier avec ces codes et ces exigences, veuillez contacter un électricien qualifié.

3. To reduce the risk of electric shock, disconnect both standard and emergency power supplies and converter connector of the emergency

Installation Instructions are divided into

9 sections:

1. On Grid Mounting - Individual Recessed Mounting driver before servicing.

Pour réduire le risque de décharge électrique, vous devez déconnecter

à la fois le disjoncteur divisionnaire ou les fusibles et les alimentations d’urgence avant l’entretien.

4. Do not use outdoors.

2. On Grid Mounting - Continuous Row Recessed

Mounting

3. Off Grid Mounting (Hard Ceiling) - Individual

Recessed Mounting

Ne pas utiliser à l’extérieur.

5. Do not let power supply cords touch hot surfaces.

Ne laissez pas les cordons d’alimentation toucher les surfaces chaudes.

6. Do not mount near gas or electric heaters.

4. Off Grid Mounting (Hard Ceiling) - Continuous Row

Recessed Mounting

5. Smartcast Option

6. Stylus with Lutron Vive RF Sensor Option

Ne montez PAS près des appareils de chauffage de gaz ou

électriques.

7. Do Not use this equipment for other than its intended use.

NE PAS utiliser cet équipement à d’autres fins que celle qui est prévue

7. Stylus with Wall Wash Optic Option

8. Emergency Driver Check

9. Electrical Connections

8. Equipment should be mounted in locations and heights where it will not readily be subjected to tampering by unauthorized personnel.

L’équipement doit être monté dans des endroits et à des hauteurs où il ne sera pas soumis à des altérations par des personnes non autorisées.

9. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.

L’utilisation d’accessoires non recommandés par le fabricant peut causer une situation dangereuse.

10. SUITABLE FOR CONTINUOUS ROW MOUNTING.

PEUT ÊTRE MONTÉ EN RANGÉE CONTINUE.

11. Suitable for Damp Locations.

Convient aux emplacements humides.

12. MIN. 90C SUPPLY CONDUCTORS.

LES FILS D’ALIMENTATION 90C MIN.

13. INHERENTLY PROTECTED.

14. TYPE IC. VAPOR BARRIER MUST BE SUITABLE FOR 90C.

TYPE IC. LE PARE-VAPEUR DOIT CONVENIR POUR 90 °C.

PROTECTION INHERENTE.

15. Make sure the equipment is properly grounded.

16. Always de-energize the circuit and/or equipment before connecting to, disconnecting from or servicing the equipment

SAVE THESE INSTRUCTIONS FOR FUTURE

REFERENCE

NOTES:

• CAUTION It is the installers responsibility to ensure that ceiling is structurally capable of supporting the weight of luminaire/luminaire row.

• Endcap kits and joining hardware are packaged separately for continuous rows.

• To Prevent Luminaire Row From Over-Current: By adding the input current of each luminaire section marked on the luminaire, the total current per power feed must not exceed the maximum line wire amperage rating in the luminaire and the power feed cord/wire amperage rating whichever is least.

1 of 9 LPN00644X0015A0_D

ON GRID MOUNTING

TO INSTALL:

1

Flexible Conduit

(Supplied By Others)

1" T-bar

Flush Ceiling Tile

9/16" T-bar

Flush Ceiling Tile

Screw Slot

T-bar

OFF GRID MOUNTING

1" T-bar

Tegular Tile

9/16" T-bar

Tegular Tile

Hard Ceiling

Flangeless

Hard Ceiling

Overlap Flange

Support Cable

(Supplied By Others)

#10-18 X 1/4”

Phillips Head

Screws

LED Tray

Lens

SECTION 1:

ON GRID MOUNTING - INDIVIDUAL RECESSED MOUNTING

CAUTION: Ceiling contractor must provide an uninterrupted, continuous rough opening utilizing tee grids spaced at 4" center to center. Length of opening should be determined from Figure 3 on next page.

Tee grids must be secured to structure above to support weight of luminaire.

CAUTION: Luminaires should be secured to structure above to support weight of luminaire.

STEP 1:

Remove lens and upper LED/reflector tray and set aside in order of run placement for reinstalling later. To remove lens, carefully slide a plastic card or putty knife between the lens and extrusion towards the end of the luminaire. Using the plastic card or putty knife, push the lens inward until the lens comes free. See Figure 1 and 2 on next page..

STEP 2:

After removing the lens, remove the Philips head reflector screws, remove the LED

Reflector Tray, and disconnect the LED harness. Set lens and LED Reflector tray aside. See Figure 1.

2 of 9

STEP 3:

Attach customer supplied support cables to luminaire and structure above as shown in

Figure 1 :

STEP 4:

Using one of the 7/8” diameter holes on the end of the luminaire, install customer supplied conduit and make electrical connections per

Section 5 “ Electrical Connections ”

STEP 5:

Reconnect LED harness. Replace LED trays and lens that was removed in Step 1 & 2 above, ensure that no wires are pinched.

LPN00644X0015A0_D

2

Extrusion

Lens

Slide Plastic Card or

Putty Knife Here

3

LUMINAIRE ROW LAYOUT: SINGLE UNIT 2' - 12'

2’ FIXTURE

23.25"

0.19"

4’ FIXTURE

0.19" Endcap

Thickness

47.25"

0.19" Endcap

Thickness

6’ FIXTURE

0.19" Endcap

Thickness

71.25"

0.19" Endcap

Thickness

8’ FIXTURE

0.19" Endcap

Thickness

95.25"

0.19" Endcap

Thickness

10’ FIXTURE

0.19" Endcap

Thickness

119.25"

0.19" Endcap

Thickness

12’ FIXTURE

0.19" Endcap

Thickness

0.19" Endcap

Thickness

143.25"

0.19" Endcap

Thickness

***NOTE: Plugged holes provided for conduit entry are located 2" from both ends of each luminaire.

***NOTE: Luminaires intended for Hard Off Grid Ceiling are to be installed with threaded rod to structure above ‘by others’ and should be installed accordance with these instructions. Plugged holes for threaded rod attachment are located 4in from both ends of each luminaire.

3 of 9 LPN00644X0015A0_D

4

End Plate Cap (After

Trimming Has Been Done)

7/8" Plugged Hole for Conduit Entry

5

Female End

Male End

(4) #6 Screws

6 Safety Wires

(Supplied by Others)

End Cap

5/8" Plugged Hole for

Threaded Rod Attachment

(Off-Grid Mounting ONLY)

Female End Male End

Safety Wires

Alignment Pins

Safety Wires Brackets

LED Tray

Lens

End Cap

SECTION 2:

ON GRID MOUNTING - CONTINUOUS ROW RECESSED MOUNTING

CAUTION: Ceiling contractor must provide an uninterrupted, continuous rough opening utilizing tee grids spaced 4” center to center.

Length of opening should be determined from

Figure 7 on next page.

Tee grids and luminaire must be secured to structure above to support weight of luminaire.

CAUTION: Do not attempt to assemble luminaire rows on the ground and then lift into position. This may create stress at the connection points and may result in damage and/or mechanical failure.

CAUTION: Do not connect power in a run until all of run is installed, wire harnesses connected, and luminaire joints completed.

STEP 1:

Remove lens and LED/reflector tray and set aside in order of run placement for reinstalling later. To remove lens, carefully slide a plastic card or putty knife between the lens and extrusion towards the end of the luminaire.

Using the plastic card or putty knife, push the lens inward until the lens come free. After removing the lens, remove the Philips head

4 of 9 reflector screws, remove the LED Reflector Tray, and disconnect the LED harness. Set lens and

LED Reflector tray aside. See Figure 1 and 2.

STEP 2:

Locate and install End Cap Kits. Install End Cap with (4) #6 screws from end cap kit. The end cap has to be trimmed, the amount depends on the run length. Each notch corresponds to the successive Trim Length section in the chart on the next page (See Figure 7 ). In order to install the end cap on the male end of the luminaire, replace the male joiner bracket with the female joiner bracket and remove the alignment pins.

See Figure 4 and 6.

STEP 3:

Lay the first luminaire Right-Hand End of the Row into the grid per Figure 7 grid requirements.

STEP 4:

Position second luminaire in row such that it aligns with joint end (male end) of first luminaire. Attach using customer supplied hardware to structure above. Connect the second luminaire to the first luminaire as shown in Figure 5 and 6 . Plug wire harness together and push excess wire into luminaire wiring chamber, ensure that wires are not pinched.

STEP 5:

Push luminaires tightly together while making sure the alignment pins slide into the interior tracks of each luminaire and span the luminaire joint. Secure joint by tightening supplied keps locknuts on threaded studs of male joiner bracket. Attach safety wires to luminaire safety wire bracket and structure above as shown in

Figure 5 and 6 .

STEP 6:

Continue to install and assemble row following steps 1-5 above. Using one of the 7/8" dia. holes on the End unit (Left-Hand End of Run) luminaire, install conduit connector and make electrical connections per Section 5 “Electrical

Connections”.

STEP 7:

Replace LED trays and lens that was removed in

Step 1 above, ensure that no wires are pinched.

LPN00644X0015A0_D

7

LUMINAIRE ROW LAYOUT: EXAMPLE OF A THREE UNIT 20' - 24' (CAN BE MOUNTED IN OTHER CONFIGURATIONS)

20’ FIXTURE

46-7/8”

94-7/8”

8’ UNIT

237-1/16" End Cap to End Cap

94-7/8"

8’ UNIT

236-5/8" Aperture

4’ UNIT

24’ FIXTURE

94-7/8"

8’ UNIT

285-00" End Cap to End Cap

94-7/8"

8’ UNIT

284-5/8" Aperture

EXAMPLE 3 FIXTURE CONTINUOUS ROW

94-7/8"

8’ UNIT

Feet

26

28

30

32

34

36

38

40

42

44

46

48

58

60

62

64

66

68

70

72

50

52

54

56

14

16

18

20

22

24

1

1

1

1

1

1

1

1

1

1

4'

1

1

1

1

Units

1

1

1

1

1

1

1

1

6'

1

1

1

1

1

1

1

8'

3

4

3

4

4

2

3

5

5

6

5

4

1

2

2

3

1

2

7

8

7

8

8

9

6

7

6

7

5

6

Continous Row

Length (in)

End Cap to

End Cap

166.25

190.13

213.06

237.06

261.06

285.00

308.00

332.00

356.00

380.00

402.88

426.88

450.88

474.88

497.81

521.81

545.81

569.81

592.75

616.75

640.75

664.75

687.63

711.63

735.63

759.63

782.50

806.50

830.50

854.50

End Cap

Kits

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

Trim Length for Endcaps (in)

(For On Grid

Mounting ONLY)

2.125

2.625

2.625

2.625

2.625

3.1875

3.1875

3.1875

3.1875

3.75

3.75

3.75

3.75

4.25

4.25

4.25

4.25

4.75

4.75

4.75

4.75

1

1

1.5

1.5

1.5

1.5

2.125

2.125

2.125

***NOTE: Plugged holes provided for conduit entry are located 2" from both ends of each luminaire.

***NOTE: Luminaires intended for Hard Off Grid Ceiling are to be installed with threaded rod to structure above ‘by others’ and should be installed accordance with these instructions. Plugged holes for threaded rod attachment are located

4" from both ends of each luminaire.

Continous Row Layout

Notches

5 of 9

End Plate (Before

Trimming Has Been Done)

LPN00644X0015A0_D

8

Flexible Conduit

Supplied By Others

Support Nut

Supplied By Others

LED Tray

Lens

Threaded Support Rods Supplied By Others

#10-18 X 1/4”

Phillips Head Screws

9

10

Sheetrock Mud

Supplied By Others

6 of 9

4.25"

Ceiling opening width for Flangeless

3.37"

Ceiling opening width overlapping flange

Threaded Support Rod

Supplied by Others

Sheetrock Mud

Supplied By Others

SECTION 3:

OFF GRID MOUNTING (HARD CEILING) -

INDIVIDUAL RECESSED MOUNTING

CAUTION: Ceiling contractor must provide an uninterrupted, continuous rough opening. Dimensions of opening should be determined using Figure 3 on page 3 and Figure 9.

CAUTION: Luminaires should be secured to structure above using customer supplied threaded rods to support weight of luminaire.

STEP 1:

Remove lens and LED/reflector tray and set aside in order of run placement for reinstalling later. To remove lens, carefully slide a plastic card or putty knife between the lens and extrusion towards the end of the luminaire. Using the plastic card or putty knife, push the lens inward until the lens come free. After removing the lens, remove the Philips head reflector screws, remove the LED Reflector Tray, and disconnect the LED harness. Set lens and LED Reflector tray aside. See Figure 2 and 8.

STEP 2:

Using one of the 7/8" dia. holes on the end of the fixture, install conduit connector. See Figure 8.

STEP 3:

Install fixture from below into ceiling opening. Attach customer supplied threaded rods to luminaire through 5/8" mounting holes located on the top of the housing and to the structure above as shown in Figure 8 . Confirm that fixture is pulled up firm to ceiling line.

STEP 4:

Make electrical connections per Section 5 “Electrical

Connections” to leads in wiring compartment.

STEP 5:

Reconnect LED harness. Replace LED trays and lens that was removed in Step 1 above, ensure that no wires are pinched.

STEP 6:

For Hard Ceiling, Overlap Flange Only:

Fill in Sheet Rock mud over tapered extruded flange until smooth. See Figure 10.

LPN00644X0015A0_D

11

Wire Harness

Second Luminaire

First Luminaire

Male End

Female End

SECTION 4:

OFF GRID MOUNTING (HARD CEILING) -

CONTINUOUS ROW RECESSED MOUNTING

CAUTION: Ceiling contractor must provide an uninterrupted, continuous rough opening. Dimensions of opening should be determined using Figure 7 on page 5 and

Figure 9.

CAUTION: Luminaires should be secured to structure above to support weight of luminaire.

CAUTION: Do not attempt to assemble luminaire rows on the ground and then lift into position. This may create stress at the connection points and may result in damage and/or mechanical failure.

CAUTION: Do not connect power in a run until all of run is installed, wire harnesses connected, and luminaire joints completed.

STEP 1:

Remove lens and LED/reflector tray and set aside in order of run placement for reinstalling later. To remove lens, carefully slide a plastic card or putty knife between the lens and extrusion towards the end of the luminaire. Using the plastic card or putty knife, push the lens inward until the lens come free. After removing the lens, remove the Philips head reflector screws, remove the LED Reflector Tray, and disconnect the

LED harness. Set lens and LED Reflector tray aside. See Figure 2 and 6.

STEP 2:

Install the first luminaire (Right-Hand End of Run) from below into ceiling opening.

Attach customer supplied threaded rods to luminaire through 5/8" mounting holes located on the top of the housing and to the structure above as shown in Figure 7 and 8 .

Confirm that fixture is pulled up firm to ceiling line.

STEP 3:

Position second luminaire in row such that it aligns with joint end (male end) of first luminaire. Attach customer supplied supports to fixture through mounting holes located on the top of the housing and to the structure above as shown in Figure 11 . Confirm that fixture is pulled up firm to ceiling line. Connect

7 of 9 the second luminaire to the first luminaire as illustrated in Figure 5 . Plug wire harness together and push excess wire into luminaire wiring chamber, ensure that no wires are pinched. See Figure 11.

STEP 4:

Push luminaires tightly together while making sure the alignment pins slide into the interior tracks of each luminaire and span the luminaire joint. Secure joint by tightening supplied keps locknuts on threaded studs of male joiner bracket.

Confirm that luminaires are secured to the structure above. See Figure 11.

STEP 5:

Continue to install and assemble row following steps 1-4 above. Using one of the 7/8" dia. holes on the End unit (Left-

Hand End of Run) luminaire, install conduit connector and make electrical connections per Section 5 “Electrical Connections”.

STEP 6:

Reconnect LED harness. Replace LED trays and lens that was removed in Step 1 above, ensure that no wires are pinched..

STEP 7:

Hard Ceiling, Overlap Flange Only:

Fill in Sheet Rock mud over tapered extruded flange until smooth. See Figure 10.

SECTION 5:

SMARTCAST

COMMISSIONING

NOTE: Cree Lighting recommends reviewing the Cree Lighting SmartCast Technology

Wireless Deployment Guide prior to installing luminaires with Cree Lighting

SmartCast Technology.

NOTE:

• Visit Cree Lighting’s website for the guide: www.creelink.com/exLink.asp?2361356

4OH88E44I39771048&view=1

NOTE: SmartCast luminaires must be installed on unswitched AC power. Constant power is required to maintain all luminaires on the Smartcast network. If wall control or manual dimming is required, a SmartCast wall control dimmer must be used for manual on, off, and dimming.

NOTE: Before beginning fixture installation or OneButton Setup, it is important to consider the use of spaces and what luminaires will be grouped together. Cree

Lighting recommends turning on AC power to luminaires that should be grouped together and then initiating the OneButton

Setup while the remaining luminaires are switched off of AC power. It is recommended to commission one group first and then turn AC power on to the second group and continue until all luminaries are commissioned.

NOTE: Continuous rows with SmartCast ship with a dedicated sensor per fixture except for corners. Corners ship with accessible dimming leads that need to be wired into the adjacent luminaire so that the corner luminaire is controlled by the sensor of the adjacent runner. Locate dimming leads between adjacent fixture driver and sensor.

Connect corner dim leads into adjacent dimming leads.

LPN00644X0015A0_D

12 13

PIR

Wall

Reset Button

LED

ALS/ Blue

Status LED

RESET RF MODULE

NOTE: For the Blue Status LED location see Figure 12 on the next page .

STEP 1:

Actuate RESET button through the access hole using a paper clip. Push and hold until Blue Status LED, begins blinking rapidly (approximately

6-7 seconds). See Figure 12 on the next page .

STEP 2:

Release for 1 sec.

STEP 3:

Press/Hold RESET button for 0.5 sec. Light will turn off for a few seconds then go to full bright and the Blue Status LED should begin a 2 blink sequence. See Figure 12 on the next page .

TROUBLESHOOTING:

Out of the box, if the light does not turn on when power is applied:

• Check Wiring with power off

• If wired correctly, check to see if Blue Status LED blinking on the RF Module.

• If Blue Status LED is blinking, then perform a RESET

(See RESET RF MODULE section).

• If Blue Status LED is on solid or off, call Cree Lighting Customer

Service.

• If you have done a RESET, and the light is still off, call Cree

Lighting Customer Service.

If light is unresponsive, use Cree Lighting Configuration Tool to verify configuration.

SECTION 6:

STYLUS WITH LUTRON VIVE RF SENSOR OPTION

NOTE: Fixtures ordered with Vive are provided with a factory installed, integrated Lutron Vive wireless fixture control with occupancy and daylight sensor.

NOTE: For set-up, programming, and troubleshooting with a Vive system, please refer to the installation instructions included with the

Vive hub or at www.lutron.com

DEFAULT FUNCTIONALITY FIXTURE CONTROL SETTINGS:

• Auto On level: DFCSJ-OEM-OCC only

• Varies with ambient light level when occupancy is triggered

( e.g., 100% for a dark room, 10% for a bright room).

• Time-out period: 15 minutes

8 of 9

SECTION 7:

STYLUS WITH WALL WASH OPTIC OPTION

STEP 1:

Wall Wash optic must be oriented so the LEDs are facing the wall. The wall wash optic was designed for optimal performance when mounted

24” from the wall. See Figure 13.

STEP 2:

The Wall Wash lens is shipped already removed from the reflector. After installing the product, unwrap and install the lens. The lens must be installed with the texture side of the lens facing the ground. The lens is installed by angling into the reflector and then laid to rest on the reflector ledges. The lens is held in place by gravity.

SECTION 8:

EMERGENCY DRIVER CHECK

NOTE: For short-term testing of the emergency function, the battery must be charged for at least one hour. The emergency driver must be charged for at least 24 hours before conducting a long-term test.

STEP 1:

When AC power is applied, the charging indicator light is illuminated, indicating the battery is being charged. When power fails, the emergency driver automatically switches to emergency power, operating the LED array. When AC power is restored, the emergency driver returns to the charging mode.

STEP 2:

Although no routine maintenance is required to keep the emergency driver functional, it should be checked periodically to ensure that it is working. The following schedule is recommended:

• Visually inspect the charging indicator light monthly. It should be illuminated.

• Test the emergency operation of the fixture at 30-day intervals for a minimum of 30 seconds. When the test switch is depressed, the LED array should operate.

• Conduct a 90-minute discharge test once a year. The LED array should operate for at least 90 minutes.

If the luminaire fails any of these checks, consult service personnel.

REFER ANY SERVICING INDICATED BY THESE CHECKS TO QUALIFIED

PERSONNEL

EMERGENCY DRIVER AND AC DRIVER MUST BE FED FROM THE

SAME BRANCH CIRCUIT.

LPN00644X0015A0_D

FCC NOTICE

To comply with the FCC RF exposure compliance requirements, this device and its antenna must not be co-located or operating to conjunction with any other antenna or transmitter.

This equipment should be installed and operated with minimum distance 5cm between the radiator & your body.

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved could void your authority to use this equipment.

This device complies with Part 15 of the

FCC Rules. Operation to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

This device has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference when the device is operated in a commercial environment. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this device in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

CAN ICES-005 (A)/NMB-005 (A)

The LED in the front of this device operates within Risk Group 1 levels per IEC 62471.

INDUSTRY CANADA STATEMENT

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. In addition, this device complies with ICES-005 of the

Industry Canada (IC) Regulations.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

SECTION 9:

ELECTRICAL CONNECTIONS

STEP 1:

For 120/277V applications make the following Electrical Connections: a. Connect the black luminaire lead to the unswitched voltage supply lead. b. Connect the red luminaire lead to the switched supply switched.

c. Connect the white luminaire lead to the neutral supply lead.

d. Connect the green or green/yellow ground lead to the green supply lead.

For 208/240V applications, make the following Electrical Connections: a. Connect unswitched Hot 1 supply lead to the black lead.

b. Connect Hot 2 supply lead to the white lead c. Connect the red luminaire lead to the switched supply switched.

d. Connect the green or green/yellow ground lead to the supply ground lead.

STEP 2: a. If Dimming is an option; connect the violet dimming positive lead to the supply dimming positive lead. If dimming is not being used, ensure to cap off the violet lead. b. If Dimming is an option; connect the grey or pink dimming negative lead to the supply dimming negative lead. If dimming is not being used, ensure to cap off the grey or pink lead.

STEP 3:

** NOTE: DO NOT mate leads until installation is complete and AC power is supplied.

a. Locate the battery harness from the battery pack and connect it to the receptacle on the emergency driver.

© 2021 Cree Lighting, A company of IDEAL INDUSTRIES. All rights reserved. For informational purposes only. Content is subject to change. See www.creelighting.com/warranty for warranty and specifications. Cree ® and the Cree Lighting logo are registered trademarks of Cree, Inc. Styllus Linear™ and the Styllus Linear logo are trademarks of Cree Lighting, A company of IDEAL INDUSTRIES.

9 of 9

GREEN

NEUTRAL OR HOT 2

SWITCHED HOT

UNSWITCHED HOT

DIM (+) VIOLET

DIM (-) GREY

OR PINK

LUMINAIRE

GROUND-GREEN

NEUTRAL-WHITE

RED

BLACK

VIOLET

GREY

OR PINK www.creelighting.com

LPN00644X0015A0_D