Styllus Linear TM Series
LED Ambient Luminaire
Ceiling/Surface Mount
INSTALLATION INSTRUCTIONS
INSTRUCTIONS D’INSTALLATION
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed
including the following:
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS
1.
DANGER- Risk of shock- Disconnect power before installation.
DANGER – Risque de choc – Couper l’alimentation avant l’installation.
This luminaire must be installed in accordance with the NEC or your local
electrical code. If you are not familiar with these codes and requirements,
consult a qualified electrician.
Ce produit doit être installé conformément à NEC ou votre code électrique
local. Si vous n’êtes pas familier avec ces codes et ces exigences, veuillez
contacter un électricien qualifié.
SUITABLE FOR CONTINUOUS ROW MOUNTING.
PEUT ÊTRE MONTÉ EN RANGÉE CONTINUE.
Make sure the equipment is properly grounded.
Always de-energize the circuit and/or equipment before connecting to,
disconnecting from or servicing the equipment
2.
3.
4.
5.
Installation Instructions are divided into
3 sections:
1. Surface Mounting - Individual Luminaire
2. Surface Mounting - Continuous Row
3. SmartCast Option
SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE
4. Styllus with Lutron Vive RF Sensor Option
5. Styllus with Wall Wash Optic Option
6. Electrical Connections
NOTES:
• CAUTION - It is the installers responsibility to ensure that ceiling is structurally capable of supporting the weight of luminaire/luminaire row.
• Endcap kits and joining hardware are packaged separately for continuous rows.
• To Prevent Luminaire Row From Over-Current: By adding the input current of each luminaire section marked on the luminaire, the total current per
power feed must not exceed the maximum line wire amperage rating in the luminaire and the power feed cord/wire amperage rating whichever is
least.
ST3-SF
1 of 7
LPN00644X0006A0_E
TO INSTALL:
1
Chalk Line
LED Reflector
Tray
Fasteners
(Supplied By Others)
Lens
Fasteners
2
Extrusion
Lens
Slide Plastic Card
or Putty Knife Here
SECTION 1:
SURFACE MOUNTING-INDIVIDUAL LUMINAIRE
CAUTION: Luminaires should be secured
to structure above to support weight of
luminaire.
harness. Set lens and LED Reflector tray
aside. See Figure 1.
STEP 1:
Use the luminaire as a template to locate the
mounting holes by centering luminaire over
recessed switch box. Keep the switch box square
to and on center lengthwise, mark each mounting
anchors hole location, See Figure 2. Ensure that
all mounting points are on the same center line
as the switch box installed. Drill appropriate holes
for mounting surface and fasteners to be used.
Securely attach housing to ceiling: See Figure 1.
Remove lens and LED/reflector tray and set
aside in order of run placement for reinstalling
later. To remove lens, carefully slide a plastic
card or putty knife between the lens and
extrusion towards the end of the luminaire.
Using the plastic card or putty knife, push the
lens inward until the lens comes free. See
Figure 1 and 2.
STEP 2:
After removing the lens, remove the Phillips
head reflector screws, remove the LED
Reflector Tray, and disconnect the LED
2 of 7
STEP 3:
STEP 4:
Using the 1.5” diameter hole located in the
center of the luminaire, route the electrical
leads out into customer supplied junction box
and make electrical connections per Section 3
“Electrical Connections”.
STEP 5:
Reconnect LED harness. Replace LED trays
and lens that was removed in Step 1 & 2
above, ensure that no wires are pinched.
NOTE: Pre-drilled diameter 5/8" mounting
anchor holes are located 2.13" from the end
of each luminaire. See Figure 3 on the next
page.
LPN00644X0006A0_E
3
LUMINAIRE ROW LAYOUT: SINGLE UNIT 2' - 12'
2’ FIXTURE
24.25"
0.13" Endcap
Thickness
0.13"
4’ FIXTURE
48.25"
0.13" Endcap
Thickness
0.13" Endcap
Thickness
6’ FIXTURE
72.25"
0.13" Endcap
Thickness
0.13" Endcap
Thickness
8’ FIXTURE
96.25"
0.13" Endcap
Thickness
0.13" Endcap
Thickness
10’ FIXTURE
120.25"
0.13" Endcap
Thickness
0.13" Endcap
Thickness
12’ FIXTURE
144.25"
0.13" Endcap
Thickness
0.13" Endcap
Thickness
***NOTE: Plugged holes provided for feed wire in the center of each luminaire.
2”
5/8" Mounting Anchor Holes
1 1/2" Plugged Hole For Feed Wire
5/8" Mounting Anchor Holes
3 of 7
LPN00644X0006A0_E
5/8" Mounting Hole
4
End Plate Cap (With
Alignment Pins)
5
Male End
Female Joiner Bracket
Female End
Slide Screw w/
Lock Nuts
End-Plate
Lock Nuts
Alignment Pins
6
Chalk Line
Female End
Male End
Second Luminaire
First Luminaire
SECTION 2: SURFACE MOUNTING - CONTINUOUS ROW MOUNTING
CAUTION: Ceiling contractor must provide
appropriate anchors to support weight of ceiling
mount linear luminaires.
CAUTION: Do not attempt to assemble
luminaire rows on the ground and then lift
into position. This may create stress at the
connection points and may result in damage
and/or mechanical failure.
CAUTION: Do not connect power in a run until
all of run is installed, wire harnesses connected,
and luminaire joints completed.
STEP 1:
From center line of lengthwise mounted switch
box(es), snap a lengthwise chalk line on ceiling
to the right of Junction box approximately the
full length of the row to be installed.
STEP 2:
Remove lens and upper LED/reflector tray
and set aside in order of run placement for
reinstalling later. To remove lens, carefully slide
a plastic card or putty knife between the lens
and extrusion towards the end of the luminaire.
Using the plastic card or putty knife, push the
4 of 7
lens inward until the lens come free. After
removing the lens, remove the Philips head
reflector screws, remove the LED Reflector Tray,
and disconnect the LED harness. Set lens and
LED Reflector tray aside. See Figure 1 and 2.
STEP 3:
Locate and install End Cap Kits. In order to install
the end cap on the male end of the luminaire,
replace the male joiner bracket with the female
joiner bracket and remove the alignment pins.
See Figure 4 and 6.
STEP 4:
Attach the first luminaire Right-Hand End of
the Row onto the ceiling per Figure 6. Tighten
mounting screws on luminaire snug as not to
allow luminaire to move when being aligned
with the next luminaire in the row.
STEP 5:
Position second luminaire in row such that it aligns
with joint end (male end) of first luminaire. Attach
using customer supplied hardware to structure
above. Connect the second luminaire to the first
luminaire as shown in Figure 5 and 6. Plug wire
harness together and push excess wire into
luminaire wiring chamber, ensure that wires are
not pinched.
STEP 6:
Push luminaires tightly together while making
sure the alignment pins slide into the interior
tracks of each luminaire and span the luminaire
joint. Secure joint by tightening supplied keps
locknuts on threaded studs of male joiner
bracket. Figure 5 and 6.
STEP 7:
Continue to install and assemble row following
steps 1-6 above. Locate and install Junction box
to be centered on the End unit (Left-Hand End of
Run) luminaire, make electrical connections per
Section 5 “Electrical Connections”.
STEP 7:
Replace LED trays and lens that was removed in
Step 1 above, ensure that no wires are pinched.
LPN00644X0006A0_E
LUMINAIRE ROW LAYOUT: EXAMPLE OF A TWO AND THREE UNIT
16', 20' - 24' (CAN BE MOUNTED IN OTHER CONFIGURATIONS)
7
16’ FIXTURE
192-1/4" End Cap to End Cap
96 -1/8"
96 -1/8”
8’ UNIT
8’ UNIT
92” Mounting Center
92” Mounting Center
20’ FIXTURE
240-1/4" End Cap to End Cap
96 -1/8"
96 -1/8"
8’ UNIT
48-1/8""
8’ UNIT
92” Mounting Center
4’ UNIT
92” Mounting Center
44” Mounting Center
24’ FIXTURE
288-1/4" End Cap to End Cap
96 -1/8"
96 -1/8"
8’ UNIT
96 -1/8"
8’ UNIT
92” Mounting Center
8’ UNIT
92” Mounting Center
92” Mounting Center
EXAMPLE 3 FIXTURE CONTINUOUS ROW
FEED LOCATION
***NOTE: Plugged holes provided for feed wire in the
center of each luminaire.
Feet
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
5 of 7
4'
1
1
Units
6'
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
8'
1
2
1
2
2
3
2
3
3
4
3
4
4
5
4
5
5
6
5
6
6
7
6
7
7
8
7
8
8
9
End Cap
Kits
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Total Row Length (in) Endcap To Endcap
168.25
192.25
216.25
240.25
264.25
288.25
312.25
336.25
360.25
384.25
408.25
432.25
456.25
480.25
504.25
528.25
552.25
576.25
600.25
624.25
648.25
672.25
696.25
720.25
744.25
768.25
792.25
816.25
840.25
864.25
LPN00644X0006A0_E
8
9
PIR
Wall
Reset Button
LED
ALS/ Blue
Status LED
SECTION 3: SMARTCAST COMMISSIONING
NOTE: Cree Lighting recommends reviewing the Cree Lighting
SmartCast Technology Wireless Deployment Guide prior to installing
luminaires with Cree Lighting SmartCast Technology.
NOTE:
• https://cree.widen.net/s/pplfkqkrwt/smartcastr-wirelessdeployment-guide
NOTE: SmartCast luminaires must be installed on unswitched AC
power. Constant power is required to maintain all luminaires on the
SmartCast network. If wall control or manual dimming is required, a
SmartCast wall control dimmer must be used for manual on, off, and
dimming.
NOTE: Before beginning fixture installation or OneButton Setup, it is
important to consider the use of spaces and what luminaires will be
grouped together. Cree Lighting recommends turning on AC power
to luminaires that should be grouped together and then initiating the
OneButton Setup while the remaining luminaires are switched off of AC
power. It is recommended to commission one group first and then turn
AC power on to the second group and continue until all luminaries are
commissioned.
NOTE: Continuous rows with SmartCast ship with a dedicated sensor
per fixture except for corners. Corners ship with accessible dimming
leads that need to be wired into the adjacent luminaire so that the
corner luminaire is controlled by the sensor of the adjacent runner.
Locate dimming leads between adjacent fixture driver and sensor.
Connect corner dim leads into adjacent dimming leads.
TROUBLESHOOTING:
Out of the box, if the light does not turn on when power is applied:
•
•
•
•
•
Check Wiring with power off
If wired correctly, check to see if Blue Status LED blinking on
the RF Module.
If Blue Status LED is blinking, then perform a RESET
(See RESET RF MODULE section).
If Blue Status LED is on solid or off, call Cree Lighting Customer
Service.
If you have done a RESET, and the light is still off, call Cree
Lighting Customer Service.
If light is unresponsive, use Cree Lighting Configuration Tool to verify
configuration.
SECTION 4: STYLLUS WITH LUTRON VIVE RF SENSOR
OPTION
NOTE: Fixtures ordered with Vive are provided with a factory installed,
integrated Lutron Vive wireless fixture control with occupancy and
daylight sensor.
NOTE: For set-up, programming, and troubleshooting with a Vive
system, please refer to the installation instructions included with the
Vive hub or at www.lutron.com
DEFAULT FUNCTIONALITY FIXTURE CONTROL SETTINGS:
• Auto On level: DFCSJ-OEM-OCC only
RESET RF MODULE
• Varies with ambient light level when occupancy is triggered
( e.g., 100% for a dark room, 10% for a bright room).
NOTE: For the Blue Status LED location see Figure 8.
• Time-out period: 15 minutes
STEP 1:
Actuate RESET button through the access hole using a paper clip. Push
and hold until Blue Status LED, begins blinking rapidly (approximately
6-7 seconds). See Figure 8.
STEP 2:
Release for 1 sec.
STEP 3:
Press/Hold RESET button for 0.5 sec. Light will turn off for a few
seconds then go to full bright and the Blue Status LED should begin a 2
blink sequence. Figure 8.
6 of 7
SECTION 5: STYLLUS WITH WALL WASH OPTIC OPTION
STEP 1:
Wall Wash optic must be oriented so the LEDs are facing the wall. The
wall wash optic was designed for optimal performance when mounted
24” from the wall. See Figure 9.
STEP 2:
The Wall Wash lens is shipped already removed from the reflector. After
installing the product, unwrap and install the lens. The lens must be
installed with the texture side of the lens facing the ground. The lens
is installed by angling into the reflector and then laid to rest on the
reflector ledges. The lens is held in place by gravity.
LPN00644X0006A0_E
FCC NOTICE
To comply with the FCC RF exposure compliance requirements,
this device and its antenna must not be co-located or operating to
conjunction with any other antenna or transmitter.
This equipment should be installed and operated with minimum
distance 5cm between the radiator & your body.
FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved could void
your authority to use this equipment.
This device complies with Part 15 of the FCC Rules. Operation to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation
This device has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the device is operated in a commercial environment.
This device generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of
this device in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his
own expense.
The LED in the front of this device operates within Risk Group 1 levels
per IEC 62471.
INDUSTRY CANADA STATEMENT
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation
of the device. In addition, this device complies with ICES-005 of the
Industry Canada (IC) Regulations.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
CAN ICES-005 (A)/NMB-005 (A)
SECTION 6:
ELECTRICAL CONNECTIONS
STEP 1:
For 120/277/347V applications make the following Electrical
Connections:
For 208/240V applications, make the following Electrical
Connections:
a. Connect Hot 1 supply lead to the black lead.
b. Connect Hot 2 supply lead to the white lead
c. Connect the green or green/yellow ground lead to
the supply ground lead.
CORD/ SUPPLY WIRING
a. Connect the black luminaire lead to the supply lead.
b. Connect the white luminaire lead to the neutral
supply lead.
c. Connect the green or green/yellow ground lead to
the green supply lead.
LUMINAIRE
LINE OR HOT 1
LINE-BLACK
GREEN
GROUND-GREEN
NEUTRAL OR HOT 2
NEUTRAL-WHITE
DIM (+) VIOLET
VIOLET
DIM (-) GREY
OR PINK
GREY OR PINK
STEP 2:
a. If Dimming is an option; connect the violet dimming
positive lead to the supply dimming positive lead. If
dimming is not being used, ensure to cap off the violet
lead.
b. If Dimming is an option; connect the grey or pink
dimming negative lead to the supply dimming negative
lead. If dimming is not being used, ensure to cap off
the grey or pink lead.
© 2021 Cree Lighting, A company of IDEAL INDUSTRIES. All rights reserved. For informational purposes only. Content is
subject to change. See www.creelighting.com/warranty for warranty and specifications. Cree® and the Cree Lighting logo are
registered trademarks of Cree, Inc. Styllus Linear™ and the Styllus Linear logo are trademarks of Cree Lighting, A company
of IDEAL INDUSTRIES.
www.creelighting.com
7 of 7
LPN00644X0006A0_E
">
