Sharp AR-160 Specifications

MODEL

AR-160

AR-161

DIGITAL COPYING MACHINE

OPERATION MANUAL

• GETTING STARTED

• MAKING COPIES

• STATUS INDICATORS

• GENERAL INFORMATION

Page

2

13

27

36

53

• OPTIONAL EQUIPMENT

• APPENDIX

69

CAUTIONS

Follow the cautions below when using this copier.

● The fusing area is hot. Exercise care in this area when removing misfed paper.

● Do not look directly at the light source. Doing so may damage your eyes.

● Place the copier on a firm, level surface.

● Do not install the copier in a humid or dusty location.

● When the copier is not used for a long time, for example, during prolonged holidays, turn the power switch off and remove the power cord from the outlet.

● When moving the copier, be sure to turn the power switch off and remove the power cord from the outlet.

● Do not cover the copier with a dust cover, cloth or plastic film while the power is on. Doing so may prevent heat dissipation, damaging the copier.

● Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser radiation exposure.

Cautions on laser

Wave length

Pulse times

Output power

785 nm ±10 nm

(8.141 µs ±0.1 µs)/7 mm

0.2 mW ±0.02 mW

Required in Appendix ZB of BS EN 60950 — United Kingdom

MAINS PLUG WIRING INSTRUCTIONS

The mains lead of this equipment is already fitted with a mains plug which is either a non-rewireable

(moulded) or a rewireable type. Should the fuse need to be replaced, a BSI or ASTA approved fuse to BS1362 marked or and of the same rating as the one removed from the plug must be used.

Always refit the fuse cover after replacing the fuse on the moulded plug. Never use the plug without the fuse cover fitted.

In the unlikely event of the socket outlet in your home not being compatible with the plug supplied either cut-off the moulded plug (if this type is fitted) or remove by undoing the screws if a rewireable plug is fitted and fit an appropriate type observing the wiring code below.

DANGER: The fuse should be removed from the cut-off plug and the plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet as a serious electric shock may occur.

To fit an appropriate plug to the mains lead, follow the instructions below:

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

GREEN-AND-YELLOW: Earth

BLUE:

BROWN:

Neutral

Live

As the colours of the wires in this mains lead may not correspond with coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured GREEN-AND YELLOW must be connected to the terminal in the plug which is marked with the letter E, or by the safety earth symbol Å@ , or coloured green or greenand-yellow.

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter

N or coloured black.

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red.

If you have any doubt, consult a qualified electrician.

WARNING: THIS APPARATUS MUST BE EARTHED.

CONTENTS

Page

GETTING STARTED

●

●

●

●

●

●

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

PART NAMES AND FUNCTIONS . . . . . . . . . . . . . . . . . . . . 4

– Overall layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

– Operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

COPIER INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . 8

CAUTIONS ON HANDLING . . . . . . . . . . . . . . . . . . . . . . . . . 9

LOADING COPY PAPER . . . . . . . . . . . . . . . . . . . . . . 10

MAKING COPIES

●

●

●

●

●

●

●

●

●

●

AUDITING ACCOUNTS . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

NORMAL COPYING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

REDUCTION/ENLARGEMENT/ZOOM . . . . . . . . . . . . . . . 16

BYPASS FEED (special paper) . . . . . . . . . . . . . . . . . . . . 18

TWO-SIDED COPYING . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

XY ZOOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

B/W REVERSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

DUAL PAGE COPY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

INTERRUPTING A COPY RUN . . . . . . . . . . . . . . . . . . . . . 25

AUTOMATIC EXPOSURE ADJUSTMENT . . . . . . . . . . . . 26

STATUS INDICATORS

●

●

●

●

TD CARTRIDGE REPLACEMENT . . . . . . . . . . . . . . . 27

DRUM CARTRIDGE REPLACEMENT . . . . . . . . . . . . 29

MISFEED REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . 31

MAINTENANCE REQUIRED . . . . . . . . . . . . . . . . . . . 35

GENERAL INFORMATION

●

●

●

●

●

●

USER PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

– Settings for auditing accounts . . . . . . . . . . . . . . . . . . . . . . . 39

POWER SAVE MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

USER MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

COPIER TROUBLE? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

SUPPLIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

– Types and sizes of copy paper . . . . . . . . . . . . . . . . . . . . . . . 49

– Genuine supplies statement . . . . . . . . . . . . . . . . . . . . . . . . . 50

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

OPTIONAL EQUIPMENT

●

●

●

●

SYSTEM CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . 54

SINGLE PASS FEEDER (AR-SP2) . . . . . . . . . . . . . . . . . . 55

ELECTRONIC SORTING KIT (AR-EB3) . . . . . . . . . . . . . . 58

– Sort/group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

– 2 in 1 or 4 in 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

– Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

– Margin shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

250-SHEET PAPER FEED UNIT (AR-DE5)/

2x250-SHEET PAPER FEED UNIT (AR-DE6) . . . . . . . . . . 66

APPENDIX

●

●

●

TRANSFER CHARGER CLEANING . . . . . . . . . . . . . . . . . 69

DRUM CARTRIDGE LIFE . . . . . . . . . . . . . . . . . . . . . . . . . 70

INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

1

2

INTRODUCTION

This copier has been designed to provide convenient copying features in a minimum amount of office space and with maximum operational ease. To get full use of all copier features, be sure to familiarise yourself with this manual and the copier.

For quick reference during copier use, keep this manual in a handy location.

This copier can be used as a laser printer and as a facsimile machine by installing optional components. However, this manual describes only the copier features. For description of the printer features and facsimile features, see their separate manuals.

Conventions used in this manual

In this manual, the following icons are used to provide the user with information pertinent to the use of the copier.

Warns the user that injury to the user or damage to the copier may result if the contents of the warning are not properly followed.

Cautions the user that damage to the copier or one of its components may result if the contents of the caution are not properly followed.

Notes provide information relevant to the copier regarding specifications, functions, performance, operation and such, that may be useful to the user.

Indicates a letter displayed in the copy quantity display.

MAIN FEATURES

q High-speed laser copying

● First-copy time is only 7.2 seconds (except in a power save mode or immediately after power on).

● Copying speed is 16 copies/min., which adapts to business use, allowing improvement of working efficiency.

w High-quality digital image

● High-quality copying at 600 dpi is performed.

● In addition to the automatic exposure mode, the manual exposure can be adjusted in five steps.

● The photo mode copying function allows clear copying of delicate halftone original images such as monochrome photos and colour photos. Photo mode is adjustable in five steps.

e Substantial copying features

● Zoom copying from 50% to 200% in 1% increments can be performed.

● Continuous copying of maximum 99 sheets can also be performed.

●

●

Useful special features such as the XY zoom, black and white reverse, and dual page copy are available.

User programs allow setting/modification of functions for customer needs. Also the user programs allow the internal auditor to be controlled.

r Optional features

● An optional single pass feeder (SPF) allows automatic document feeding of up to 30 sheets.

●

●

An optional electronic sorting kit allows many useful copier features to be used. Multiple sets of copies can be sorted without the aid of a sorter and each set can be offset from the previous set. (The offset feature is provided only with the

AR-161.) Also the erase, margin shift, and 4 in 1 and 2 in 1 functions are available. (To use the 2 in 1 and 4 in 1 and sort/ group functions, an optional SPF is also needed.)

This copier can be used as a laser printer by installing an optional printer expansion kit.

● This copier can be used as a facsimile machine by installing an optional facsimile expansion kit.

t Environmentally friendly design

● Paper output tray is housed in the copier for space saving.

● Preheat mode and auto power shut-off mode are provided to reduce power consumption in standby mode.

This copier does not have an internal calendar or clock.

This copier will not be affected by the year 2000.

3

4

PART NAMES AND FUNCTIONS

Overall layout

e q o w e r t y u

!0

!4

q Platen cover

Place the original on the original table and close the platen cover before copying starts.

w Original table

Place the document to be copied here.

e Handles

Use to move the copier.

r Power switch

Press to turn copier power on and off.

t Operation panel

All copier controls are located here for easy operation.

y Paper output tray

Finished copies are deposited in the paper output tray.

u Front cover

Open to remove misfeeds and for copier servicing.

i i Paper tray

Holds 250 sheets of copy paper.

o Side cover

Open to remove misfeeds and to service the copier.

!0 Side cover handle

Lift and pull to open the side cover.

!1 Bypass tray guides

Adjust to the width of the copy paper.

!2 Bypass tray

Special papers (including transparency film) and copy paper can be fed from the bypass tray.

!3 Bypass tray extension

Pull out when feeding large paper such as B4 and A3.

!4 Charger cleaner

Use to clean the transfer charger.

!1

!2

!3


!5

!7

!8

!6

!9

@2

@0 @1

!5 Drum cartridge handle

Hold to pull out the drum cartridge.

!6 Drum cartridge

Copy images are formed on the photoconductive drum.

!7 TD cartridge lock release lever

Use to unlock the TD cartridge.

!8 TD cartridge strap

Lift to remove the TD cartridge.

!9 TD cartridge

Contains toner.

@0 Roller rotating knob

Turn to remove misfed paper.

@1 Fusing unit release levers

Lower to remove misfed paper.

The fusing unit is hot.

Take care in removing paper.

@2 Paper guide

Open to remove misfed paper.

Accessories

Operation manual . . . . . . . . . . . . . . . . . . . . . . . 1

TD cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Charger cleaner . . . . . . . . . . . . . . . . . . . . . . . . 1

5


Operation panel

q w e r t y u i o !0

!1

!2

q INTERRUPT key and indicator (p. 25)

Interrupts a copy run.

w Copy quantity display

Displays the specified copy quantity during the ready condition and displays the copy countdown as copies are made. Also see items r and @1.

e ZOOM indicator (p.17)

Lights up when a zoom ratio is set.

r Copy ratio display key (p. 17)

Press and hold down during standby to display the copy ratio in the copy quantity display.

t Zoom keys (p. 17)

Use to select any reduction or enlargement copy ratio from 50% to 200% in 1% increments.

y PAPER SIZE ENTER key (p.12)

Use to set the paper size in a tray.

u AUDIT CLEAR key (p.13)

Closes an open account.

i PAPER SIZE indicators

Light up to show the selected copy paper size.

o Alarm indicators

: Maintenance indicator (p.35)

: TD cartridge replacement required indicator

(p.27)

: Drum replacement required indicator (p.29)

: Paper required indicator (p.10)

: Misfeed indicator (p.31)

!0 POWER SAVE indicator (p. 43)

Lights up when the copier is in a power save mode.

!1 SPF indicator (p. 56)

Lights up when originals are set in the optional SPF tray.

!2 Output tray full indicator (p. 59)

Indicates copies must be removed from the paper output tray.

6

!8

!9

@0 @1 @2 @3

Not used for the copier features.

@4 @5 @6 @7 @8 @9 #0

!3 B/W REVERSE key and indicator (p. 23)

Press to reverse the black and white areas.

!4 XY-ZOOM key and indicator (p. 21)

Press to change the horizontal and vertical copy ratios independently.

!5 SORT/GROUP key and indicators (p. 59)

Press to select the sort or group mode when an optional electronic sorting kit and an optional SPF are installed.

!6 ORIGINAL DATA indicator

Blinks when the memory becomes full of scanned original image data. (Used when an optional electronic sorting kit and an optional SPF are installed)

!7 2 IN 1 / 4 IN 1 key and indicators (p. 61)

Press to select the 2 in 1 or 4 in 1 mode. (Only available when an optional electronic sorting kit and an optional

SPF are installed)

!8 AUTO/MANUAL/PHOTO key and indicators

(p. 14)

Use to sequentially select the exposure modes: AUTO,

MANUAL, or PHOTO.

!9 Light and dark keys and indicators (p. 15)

Use to adjust the MANUAL or PHOTO exposure level.

@0 Numeric keys

Use to select the desired copy quantity or to make user program entries.

@1 Zero key

Use as part of numeric keys to enter copy quantity.

Press during a continuous copy run to display the number of copies completed in the current run.

Press during standby to display the total output count.


!3

!4

!5

!6

!7

#1 #2 #3

1st display 2nd display

Press and hold down the key.

12,345

sheets output

Note: A3 size copies are counted as two copies.

@2 CLEAR key

Clears the copy quantity display or terminates a copy run.

@3 START key and indicator

Copying is possible when the indicator is on.

Press to start copying.

@4 CLEAR ALL ( ) key

Clears all selected settings and returns the copier to the initial settings.

@5 PRESET RATIO selector keys and indicators

(p. 17)

Use to sequentially select preset reduction/enlargement copy ratios: 50%, 70%, 81%, 86%, 100%, 115%, 122%,

141%, 200%.

@6 ORIGINAL SIZE ENTER key and indicators

(p. 14, 16)

Use to input the original size for automatic paper selection and automatic copy ratio selection.

@7 AUTO PAPER SELECT indicator

Paper of the proper size will be automatically selected depending on the original size and selected copy ratio when this indicator is on.

@8 TRAY SELECT key (p. 14)

Use to manually select a paper tray.

@9 AUTO IMAGE key and indicator

Press for automatic copy ratio selection.

#0 Paper feed location/misfeed location indica-

tors (p. 31)

The selected paper feed location is shown by a lit indicator ( ).

The general location of misfed paper is shown by a blinking red indicator ( ).

#1 DUAL PAGE COPY key and indicator (p. 24)

Use to make individual copies of two originals placed side by side on the original table.

#2 ERASE key and indicators (p. 63)

Press to select the edge erase and/or the centre erase mode. (Only available when an optional electronic sorting kit is installed)

#3 MARGIN SHIFT key and indicator (p. 65)

Shifts text or image on the copy to leave a binding margin on the left side of the copy. (Only available when an optional electronic sorting kit is installed)

Initial settings

The copier assumes the initial settings when it is first turned on, when the CLEAR ALL ( ) key is pressed, and approximately one minute* after the last copy is made in any mode.

● Copy ratio: 100%

●

●

Exposure: Automatic

Copy quantity: 0

●

●

●

All special copier modes: Off

Auto paper selection : On

Paper feed station: Previously selected paper tray

* This time (auto clear time) can be changed. See page 36,

USER PROGRAMS.

7

COPIER INSTALLATION

Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved.

If the copier is moved from a cool place to a warm place, condensation may form inside the copier.

Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room temperature for at least 2 hours before use.

Do not install your copier in areas that are:

● damp, humid, or very dusty

● exposed to direct sunlight

● poorly ventilated

● subject to extreme temperature or humidity changes, e.g., near an air conditioner or heater.

The copier should be installed near an accessible power outlet for easy connection.

Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements.

Also make certain the outlet is properly grounded.

Connect the copier to a power outlet which is not used for other electric appliances. If a lighting fixture is connected to the same outlet, the light may flicker.

Be sure to allow the required space around the machine for servicing and proper ventilation.

10 cm

A small amount of ozone is produced within the copier during operation. The emission level is insufficient to cause any health hazard.

NOTE:

The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m 3 ) calculated as an 8 hr. time-weighted average concentration.

However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier in a ventilated area.

8

CAUTIONS ON HANDLING

Be careful in handling the copier as follows to maintain the performance of this copier.

Do not drop the copier, subject it to shock or strike it against any object.

Do not expose the drum cartridge to direct sunlight.

Doing so will damage the surface (green portion) of the drum cartridge, causing poor copy quality.

Store spare supplies such as drum cartridges and TD cartridges in a dark place without removing from the package before use.

If they are exposed to direct sunlight, poor copies may result.

Do not touch the surface (green portion) of the drum cartridge.

Doing so will damage the surface of the cartridge, causing smudges on copies.

9

LOADING COPY PAPER

To save space, this copier has been designed with an adjustable front-loading tray, which is easily opened for paper loading. For best results, use only

SHARP recommended paper. (See page 49.)

The paper required ( ) indicator will light up when there is no copy paper in the selected paper feed station, or when the selected paper tray is not installed or is improperly installed.

When the paper size is changed in a paper tray, the size of the paper must be entered by steps 8 through 11 on page 12. If not, the edges of copies may become smudged with toner. Also, the AUTO PAPER SELECT and the AUTO IMAGE features will not function properly.

1

Gently lift and pull out the paper tray until it stops.

2

Push the pressure plate down until it locks in place.

10

Maximum height line

3

Fan the copy paper and insert it into the tray. Make sure the edges go under the corner hooks.

If you change to a different size of copy paper, the tray must be ● adjusted. See the next page.

● Set the paper along the guides.

● The tray holds up to 250 sheets of paper.

Do not load paper above the maximum height line.

4

Push the paper tray firmly back into the copier.


Left guide

Changing the copy paper size in the tray

1

Gently lift and pull out the paper tray until it stops.

2

Push the pressure plate down until it locks in place.

Front guide

3

Squeeze the lock lever of the front guide and slide the front guide to match the width of the paper.

4

Move the left guide to the appropriate slot as marked on the tray.

When using A5 copy paper, load it into the uppermost paper tray. If ● other trays (including trays in optional paper feed units) are used, paper misfeeds may occur.

5

Load copy paper into the tray.

6

Place the appropriate label to indicate the selected paper size into the recess on the right front side of the paper tray.

7

Push the paper tray firmly back into the copier.

11


12

8

To set the selected paper size, press the PAPER SIZE

ENTER key.

● The selected paper feed location indicator will blink and the corresponding paper size (which is currently set) indicator will light up steadily. All other indicators will go out.

For paper size setting, ensure that the COPY mode has been selected. However, if copying, printing or facsimile printing is being performed, paper size setting cannot be made even in the COPY mode. See Note on page 47.

9

Use the TRAY SELECT key to select the paper tray of which the paper size has been changed.

Each time the TRAY SELECT key is pressed, a paper tray will be ● indicated with a blinking paper feed location indicator. If an optional paper feed unit is not installed, this operation is not needed.

10

Use the ORIGINAL SIZE ENTER key to select the paper size which is set.

● Each time the ORIGINAL SIZE ENTER key is pressed, a paper size will be indicated with a paper size indicator.

11

Press the START key and then the PAPER SIZE ENTER key.

To change the paper size setting of another tray, repeat steps 9 to 10 ● after pressing the START key.

AUDITING ACCOUNTS

If this copier has been programmed in the auditing mode, it will not function until an assigned 3-digit account number has been entered. See page 39 for setting the auditing mode.

If the copier has been programmed in the auditing mode, “– – –” will appear in the copy quantity display in the initial conditions.

1

Enter your account number using the numeric keys.

● As each digit is entered, the dashes in the copy quantity display will disappear.

●

●

After the number is entered, the copy quantity display will change to 0.

If an unassigned number is entered, “– – –” will appear again in the copy quantity display, indicating that the number was not accepted.

2

When copying is completed, press the AUDIT CLEAR key.

● “–––” will appear again in the copy quantity display, indicating the auditing mode.

● In the interrupt copy mode (see page 25), press the INTERRUPT key after an interrupt copy run is completed. All previous copier settings will be restored and the previous account number will be active.

13

NORMAL COPYING

Power on

1

Turn the power switch on.

● It will take about 35 seconds for the copier to warm up. However, you can make desired settings and press the START key during warm-up.

●

●

Copying will start after warm-up.

If the copier has been programmed in the auditing mode, the START key indicator will not light up and “– – –” will appear in the copy quantity display. Enter an assigned 3-digit account number. See page

13.

If the power is already on and all indicators except the POWER SAVE indicator are off, the copier is in the auto power shut-off mode. Press the START key in this case. See page 43, POWER SAVE MODES.

2

Place the original face down on the original table. Align it with the original size scale.

● Image loss (max. 4 mm) can occur at the leading and trailing edges of the copies. Also image loss (max. 4 mm in total) can occur along the other edges of the copies.

3

Close the platen cover.

4

Ensure that the copy paper size in the paper tray is the same size as the original.

● If a tray of the required size is not installed, use the bypass tray and press the TRAY SELECT key to select the bypass tray.

● If an optional paper feed unit is installed:

Use the ORIGINAL SIZE ENTER key to select the original size.

Copy paper of the same size as the original will be automatically selected. If desired, another paper tray can be selected by pressing the

TRAY SELECT key.

5

Adjust the copy density.

● This copier has three exposure modes to choose from — AUTOMATIC,

MANUAL, and PHOTO.

● Automatic exposure is the standard initial setting for this copier. In this mode, the characteristics of the original are “read” by the exposure system and adjustments are automatically made. This optimizes the contrast of the copied images by reducing the effect of coloured or shaded background areas. See page 26 to adjust the automatic exposure level.

14

NORMAL COPYING

● For manual copy density adjustment, press the AUTO/MANUAL/

PHOTO key to select MANUAL and adjust with the light ( ) and dark ( ) keys as desired.

●

●

For photographs, select PHOTO and then adjust with the light ( ) and dark ( ) keys as desired.

There are 5 exposure steps indicated by 3 indicator lights. (The indicators light up one or two at a time.)

If exposure level 2 is selected, the two left-handmost indicators for that level will light up simultaneously. Also, if level 4 is selected, the two right-handmost indicators for that level will light up simultaneously.

6

Set the number of copies using the numeric keys.

● A single copy can be made with the initial setting, i.e., when “0” is displayed.

● Press the CLEAR ( ) key to clear an entry if a mistake is made.

7

Press the START key.

● The number in the copy quantity display will decrease by 1 each time a copy is made.

●

●

Press the CLEAR key to stop copying in the middle of a run.

To repeat the same copy sequence for a different original, simply replace the original and press the START key.

How to remove the platen cover

The platen cover can be removed to allow copying of bulky objects. To remove it, simply lift the platen cover straight up.

● To reattach the platen cover, reverse the above procedure.

15

REDUCTION/ENLARGEMENT/ZOOM

Reduction and enlargement ratios can be selected either automatically with the AUTO IMAGE key or manually with the PRESET RATIO selector

( , ) keys and/or the zoom ( , ) keys. The zoom function enables precise copy ratio selection from 50% to 200% in 1% increments.

Automatic

1

Place the original on the original table and close the platen cover.

2

Press the ORIGINAL SIZE ENTER key until the indicator for the size of the original on the original table lights up.

3

Use the TRAY SELECT key to select the paper tray with the desired paper size.

This feature will not work when copy paper of non-standard size is ● used or the bypass tray is used.

4

Press the AUTO IMAGE key.

● The copy ratio will be automatically set.

● If the size and orientation of the original do not correspond to standard reduction/enlargement ratios for the selected paper tray, then the

ORIGINAL SIZE indicator will blink.

However, if an optional electronic sorting kit is installed, the original image may be automatically rotated.

● If a PRESET RATIO indicator is blinking, part of the original image may not be copied.

5

Enter the number of copies.

6


● To cancel the automatic reduction/enlargement mode, press the AUTO IMAGE key again.

● When copying from an optional SPF with this feature, the automatic reduction/enlargement mode will be automatically cancelled after copying is complete.

16

REDUCTION/ENLARGEMENT/ZOOM

Manual

1


2

Use the PRESET RATIO selector ( , ) keys and the zoom ( , ) keys to select the desired copy ratio.

To select a preset reduction or enlargement copy ratio, press the ● or key repeatedly until the indicator for the desired copy ratio is lit.

A.

Preset reduction ratios are: 86%, 81%, 70%, and 50%.

B.

Preset enlargement ratios are: 115%, 122%, 141%, and 200%.

C.

Zoom ratios: Any ratio from 50% to 200% can be set, in 1% increments. Press the or key to set the approximate ratio, then press the key to decrease the ratio or the key to increase the ratio.

●

●

When a zoom ( , ) key is pressed, the ZOOM indicator will light up and the zoom ratio will be displayed in the copy quantity display for at least two seconds.

To verify a zoom setting without changing the zoom ratio, press and hold down the copy ratio display ( ) key. When the key is released, the display will return to the copy quantity display.

● To decrease or increase the zoom ratio rapidly, press and hold down the or key. However the value will stop at the preset reduction or enlargement ratios. To move beyond these ratios, release the key and then press and hold it down again.

D.

Same-size reset: Press the or key repeatedly until the copy ratio returns to 100%.

3

Ensure that copy paper of the desired size is installed in the paper tray.

If an optional paper feed unit is installed: ●


Copy paper of the appropriate paper size will be automatically selected depending on the original size and copy ratio. If the selected PRESET

RATIO indicator or the ZOOM indicator blinks, the selected copy image is too large for the copy paper size.

The desired paper tray can also be selected by pressing the TRAY

SELECT key.

4

Set the number of copies and press the START key.

17

BYPASS FEED (special paper)

The bypass tray is used to copy onto transparency film, labels, and other special purpose papers. Up to 100 sheets of standard copy paper can be set in the bypass tray.

For special purpose papers, the original image must be smaller than the paper or media for copying.

If the original image is bigger than the paper or media, this may cause smudges on the edges of the copies.

Also for standard copy paper, smudges may appear if the copy paper is not at least as large as the original image.

1

Unfold the bypass tray.

● When feeding B4 or A3 sized paper, extend the feeder tray.

2

Set the paper guides to the copy paper width.

3

Insert the copy paper (print face down) all the way into the bypass tray.

● Up to 100 sheets of standard copy paper measuring from A6 to A3 can

●

● be loaded in the bypass tray.

A6 size paper must be fed narrow into the feed slot.

Transparency film, labels, and other special purpose papers (except envelopes) must be fed individually.

●

Up to 10 envelopes can be set.

When adding paper, first remove remaining paper, combine it with the paper to be added and then reload as a single stack.

When loading envelopes, make sure that they are straight and flat.

●

18

BYPASS FEED (special paper)

4

Press the TRAY SELECT key to select the bypass tray.

5

Leave the copy quantity at 0 if using special papers. Set the number of copies if using standard copy paper or envelopes.

6


19

TWO-SIDED COPYING

Two-sided copies can be made on this copier using the bypass tray.

1

Place the first original on the original table and make a copy.

The first copy can be made using any of the paper feed stations.

●

2

Replace the first original with the second original and close the platen cover.

● Make sure that the first and second originals are oriented in the same way on the original table.

● When the originals are placed horizontally, make sure that the first and second originals are oriented in the reverse way on the original table.

3

Turn the first copy over left to right and place it into the bypass tray.

Be sure to feed the copies one sheet at a time.

●

4

Use the TRAY SELECT key to select the bypass tray.

5


20

XY ZOOM

Original Copy The XY ZOOM feature allows the horizontal and vertical copy ratios to be changed independently. This feature cannot be used with the 2 in 1 or 4 in 1 feature. (The 2 in 1 or 4 in 1 feature can only be used when an optional electronic sorting kit and an optional SPF are installed.)

To use the XY ZOOM feature with the DUAL PAGE COPY feature, set the

DUAL PAGE COPY feature first and then the XY ZOOM feature.

(Enlargement cannot be set.)

1


2

Press the XY-ZOOM key.

● The current value for the vertical direction will be displayed in the copy quantity display.

3

Use the PRESET RATIO selector ( , ) keys and zoom

( , ) keys to change the copy ratio in the vertical direction.

● Press a PRESET RATIO selector ( or ) key to set an approximate ratio, then press the key to decrease the ratio or key to increase the ratio. The copy ratio will be displayed in the copy quantity display.

4

Press the copy ratio display ( ) key.

● The selected ratio for the vertical direction will be entered and the current value for the horizontal direction will be displayed in the copy quantity display.

21

XY ZOOM

22

5

Use the PRESET RATIO selector ( , ) keys and zoom

( , ) keys to change the copy ratio in the horizontal direction in a similar manner as for the vertical direction.

6

Press the copy ratio display ( ) key.

● The selected ratio for the horizontal direction will be entered and the display will change to the copy quantity display.

● To verify the copy ratios, press and hold down the copy ratio display

( ) key. The vertical and horizontal ratios will be alternately displayed.

7

Ensure that copy paper of the desired size is installed in the paper tray.


Use the ORIGINAL SIZE ENTER key to select the original size. Copy paper of the appropriate paper size will be automatically selected depending on the original size and copy ratios. If desired, another paper tray can be selected by pressing the TRAY SELECT key.

8

Enter the desired number of copies.

9


●

●

To change the copy ratios again, press a PRESET

RATIO selector ( , ) key or a zoom ( , ) key. Then, perform step 3 and the succeeding steps.

To cancel this function, press the XY-ZOOM key again.

B/W REVERSE

Original Copy

The B/W REVERSE feature is used to reverse black and white areas.

● When the B/W REVERSE feature is selected, the exposure mode will be automatically set to the MANUAL mode. Other exposure modes cannot be selected.

Even if this feature is cancelled, the MANUAL mode will not automatically be cancelled.

1


2

Press the B/W REVERSE key.

3

Check the copy paper size.



Copy paper of the same size as the original will be automatically selected. If desired, another paper tray can be selected by pressing the

TRAY SELECT key.

4

Make all other desired copier selections and press the

START key.

23

24

DUAL PAGE COPY

Original Copy The DUAL PAGE COPY feature produces individual copies of two documents placed side by side on the original table. It is especially useful when copying books and other bound documents. This feature cannot be used with the 2 in 1 or 4 in 1 feature and sort/group feature. (The 2 in 1 or 4 in 1 feature and sort/group feature can only be used when an optional electronic sorting kit and an optional SPF are installed.) If the AUTO IMAGE feature has been selected, this feature cannot be selected.

To use the DUAL PAGE COPY feature with the XY ZOOM feature, set the

DUAL PAGE COPY feature first and then the XY ZOOM feature.

(Enlargement cannot be set.)

1

Place the originals on the original table with the centre of the two pages aligned with the paper size index

( A4). Close the platen cover.

● Set the page to be copied first to the right of the paper size index mark.

2

Press the DUAL PAGE COPY key.

● Check to be sure that the copy paper size in the paper tray is

A4.

3

Set the number of copies.

4


INTERRUPTING A COPY RUN

INTERRUPT is used to interrupt a long copy run so that another job can be done.

● If sort or group copying is being performed, sort or group cannot be selected during interrupt copying. (Sort and group can be performed only if an optional electronic sorting kit and an optional SPF are installed.)

1

Press the INTERRUPT key.

● The copier will return to the initial settings.

● If this copier has been programmed in the auditing mode using user

● program No. 10, “–––” will appear in the copy quantity display. Enter your account number using the numeric keys. The number of copies of the interrupt copying will be accumulated against this account number. See page 13.

When an optional SPF is being used, the copier will stop after completing the copying of the original which has been fed into the

SPF.

2

When the copier stops, remove the original(s) and set the original(s) for interrupt copying.

3

Select the desired available copier functions.

4


5


● The interrupt copies will be offset from the previous copies when user program No. 19 is enabled. (AR-161 only)

6

When all INTERRUPT copies are finished, press the

INTERRUPT key again to cancel the INTERRUPT mode, and remove the original used for interrupt copying.

● The previous copy quantity, copy ratio, copy density, and paper size will be automatically restored.

7

Replace the original(s) for the interrupted job on the original table or in the SPF and press the START key.

25

AUTOMATIC EXPOSURE ADJUSTMENT

The automatic exposure level can be adjusted to suit your copying needs.

This level is set for copying from the original table and copying from the optional SPF respectively. To set the level for the optional SPF, place an original in the SPF tray and make sure that the SPF indicator lights up before proceeding to step 1. To set the level for the original table, ensure that the SPF indicator does not light up.

1

Press the AUTO/MANUAL/PHOTO key to select the

PHOTO mode.

2

Press and hold down the AUTO/MANUAL/PHOTO key for approximately 5 seconds.

The PHOTO indicator will go out and the AUTO indicator will begin ● to blink.

● One or two exposure indicators corresponding to the current automatic exposure level will light up. The factory default setting is level “3”.

3

Press the light ( ) or dark ( ) key to lighten or darken the automatic exposure level as desired.

4

Press the AUTO/MANUAL/PHOTO key.

● The AUTO indicator will stop blinking and will light up steadily.

● This automatic exposure level will remain in effect until you change it again by this procedure.

26

TD CARTRIDGE REPLACEMENT

If the machine detects an insufficient amount of toner being added, copying will stop and the machine will add toner. During this time, the

START key indicator will blink. When sufficient toner has been added, the indicator will go out indicating that copying can be resumed. However, if toner addition continues for a maximum of two minutes, the TD cartridge replacement required ( ) indicator will light up in addition to the START key being lighted steadily. This indicates that the toner supply is low and a new cartridge will be needed soon. If copying is continued, the copies will gradually become lighter until the copier stops and the TD cartridge replacement required indicator begins to blink, indicating that the cartridge must be replaced. Replace the TD cartridge by following the procedure below.

For best copying results, be sure to use only

SHARP products.

The package of SHARP toner has the Genuine

Supplies label.

GENUINE SUPPLIES

1

Open the bypass tray. Lift slightly on the side cover and slide the cover out until it stops.

2

Push gently on both sides of the front cover to open the cover.

TD cartridge lock release lever

3

Lift the TD cartridge lock release lever and pull the cartridge out until the green strap handle can be grasped by the right hand. Lift the cartridge by the handle while supporting it with the left hand at the green label position to remove it.

For disposal of the old TD cartridge, contact your dealer.

●

4 or 5 times

4

Remove the new TD cartridge from the bag. Hold the cartridge on both sides and shake it horizontally four or five times.

27

TD CARTRIDGE REPLACEMENT

5

Remove the protective cover from the TD cartridge by unlatching three cover hooks from the holes on the cartridge and then pulling the cover in the direction indicated by the arrow in the illustration.

28

6

Gently insert the TD cartridge along the guides until it locks in place.

If dirt or dust is adhered to the TD cartridge, remove it before installing the cartridge.

7

Close the front cover by pushing both sides with your hands and then close the side cover by pressing the handle on the cover. The indicator will go out and the

START key indicator will light up.

When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged.

DRUM CARTRIDGE REPLACEMENT

The useful life of the drum cartridge is approximately 30,000 copies. When the internal counter reaches approximately 29,000 copies, the drum replacement required ( ) indicator will light up indicating that replacement of the drum cartridge will be needed soon. When the indicator begins to blink, replace the drum cartridge by following the procedure given below.

Do not remove the protective cover on the drum portion

(black paper) of a new drum cartridge before use. The cover protects the drum against external light.

● For the procedure to find out how many more copies can be made before the 30,000 mark is reached, see page 70, DRUM CARTRIDGE LIFE.


SHARP products.

The package of SHARP drum cartridge has the

Genuine Supplies label.


1


2


TD cartridge lock release lever

3

Lift the TD cartridge lock release lever and pull the cartridge out until the green strap handle can be grasped by the right hand. Lift the cartridge by the handle while supporting it with the left hand at the green label position to remove it.

4

Grasp the handle of the drum cartridge and gently pull the cartridge out.

For disposal of the old drum cartridge, contact your dealer.

●

29

DRUM CARTRIDGE REPLACEMENT

30

5

Remove the new drum cartridge from the protective bag and gently insert the lead end of the drum cartridge along the guides.

Do not touch the surface of the drum (green portion) of the cartridge. Doing so may cause smudges on the copies.

6

Remove the protective cover from the drum cartridge and then push the cartridge all the way into the copier.

7

Gently install the TD cartridge. To install the TD cartridge, see page 27, TD CARTRIDGE REPLACEMENT.

8

Close the front cover by pushing both sides with your hands and then close the side cover by pressing the handle on the cover. The drum replacement required

( ) indicator will go out and the START key indicator will light up.


MISFEED REMOVAL

The copier will stop when a misfeed occurs. The misfeed

( ) indicator will blink, and blinking red misfeed location indicators will indicate the approximate misfeed location.

If paper is accidentally torn during removal, be sure to remove all pieces.

Be careful not to damage the photoconductive drum.

For misfeeds in optional equipment, see their respective sections of the operation manual.

First confirm the misfeed location.

( P.57)

( P.31, 34)

( P.67)

Misfeed in the bypass tray

1

Gently pull the misfed paper out.

2

Lift slightly on the side cover and slide the cover out until it stops. Close the side cover by pressing the handle on the cover.

● The misfeed ( ) indicator will go out and the START key indicator will light up.

Misfeed in the copier

1


31

MISFEED REMOVAL

2

Check the misfeed location. Remove the misfed paper following the instructions for each location in the illustration below.

If paper is misfed here, proceed to

“B. Misfeed in the fusing area”.

If the misfed paper is seen from this side, proceed to “C. Misfeed in the transport area”.

If paper is misfed here, proceed to

“A. Misfeed in the paper feed area”.

A.

Misfeed in the paper feed area

1


Roller rotating knob

2

Carefully remove the misfed paper. Turn the roller rotating knob in the direction of the arrow to assist in removing it.

The fusing unit is hot. Take care in removing paper.

Do not touch the surface of the drum (green portion) of the drum cartridge when removing the misfed paper.

Doing so may damage the drum and cause smudges on copies.

3

Close the front cover by pushing both sides with your hands and then close the side cover by pressing the handle on the cover.



B.

Misfeed in the fusing area

1


32

MISFEED REMOVAL

Roller rotating knob

Fusing unit release lever

2

Turn the roller rotating knob in the direction of the arrow.

3

Carefully remove the misfed paper. Lower the fusing unit release levers to allow easier removal. Return the release levers to their operating positions.


●

●

Do not touch the surface of the drum (green portion) of the drum cartridge when removing the misfed paper. Doing so may damage the drum and cause smudges on copies.

Be careful about unfixed toner on the misfed paper.

4

Close the front cover by pushing both sides with your hands and then close the side cover by pressing the handle on the cover.



C.

Misfeed in the transport area

1

Open the paper guide by pressing down the projection on either side of the guide and remove the misfed paper.


2

If the misfed paper cannot be removed by the previous step but is visible in the paper output area, remove the paper by pulling it into the paper output area.

33

MISFEED REMOVAL

3

Close the side cover by pressing the handle on the cover.


Misfeed in the paper tray

Before opening the paper tray, be sure to open the bypass tray, lift slightly on the side cover and slide the cover out until it stops, and then perform steps 1 to 3 described in the “A. Misfeed in the paper feed area” section.

1

Gently lift and pull out the paper tray and remove the misfed paper.

2

Close the paper tray.

3

Lift slightly on the side cover and slide the cover out until it stops. Close the side cover by pressing the handle on the cover.


34

MAINTENANCE REQUIRED

When the indicator lights up, service by an authorised SHARP service technician is required. Contact your service centre as soon as possible.

35

USER PROGRAMS

The user programs allow the parameters of certain functions to be set, changed, or cancelled as desired.

List of user programs

This copier has the following user programs.

Program No.

Program name

1

2

3

4

5

6

7

Auto clear time

Preheat mode

Auto power shut-off timer

Stream feeding mode*

Auto power shut-off setting

Description

Border line for 2 in 1 or Enables or disables the border line which is printed in 2 in 1 or 4 in 1 copy-

4 in 1* ing when an optional electronic sorting kit and an optional SPF are installed.

See page 61.

Rotation copy*

Sets the auto clear time. The copier returns to the initial settings when the auto clear time elapses after the last copy is made.

Sets the time that elapses before the copier enters the preheat mode after any operation is made. See page 43.

Sets the time that elapses before the copier enters the auto power shut-off mode after any operation is made. See page 43.

Enables or disables the stream feeding mode when an optional single pass feeder (SPF) is installed. See page 56.

Enables or disables the auto power shut-off mode. See page 43.

Enables or disables rotation of original images. See page 58.

8

9

10

11

12

13

14

15

16

17

18

Auto paper select mode Enables or disables the auto paper selection. See page 14.

Auto tray switching*

Auditing mode

Enables or disables the automatic tray switching which occurs when paper in a tray runs out. (This switching cannot switch to the bypass tray.)

Enables or disables the auditing mode, which controls access to copier. See page 13.

Registers accounts for auditing mode.

Account number entry

Account number change

Account number deletion

Number of copies per account

Changes account numbers for auditing mode.

Deletes accounts for auditing mode.

Displays the total number of copies made against account numbers.

Resetting account Resets all audit accounts or resets any desired individual account.

Erase width adjustment* Sets the amount of the edge erase and centre erase areas. See page 63.

Layout in 2 in 1 copy*

Layout in 4 in 1 copy*

Selects a pattern for 2 in 1 copying. See page 61.

Selects a pattern for 4 in 1 copying. See page 61.

19 Offset of paper output tray

Enables or disables the offset function of the paper output tray. The offset function can be specified respectively for the upper and lower areas separated by an optional job separator tray kit. See page 59. (AR-161 only)

* These programs do not affect the copier functions unless certain optional equipment is installed.

36

USER PROGRAMS

Setting the user programs

1

Press and hold the light ( ) key for more than 5 seconds until all the alarm indicators ( , , , , and ) blink and “– –” appears in the copy quantity display.

2

Enter a program number using the numeric keys.

● The selected program number will blink in the copy quantity display.

● If a mistake is made in steps 2 to 4, press the CLEAR ( ) key. The copier will return to step 2.

The program numbers are shown in the table below.

●

For example, to change the setting of the auto power shut-off timer, press key 3.

For operation of these programs after step 3, see page 39.

Program name

Auto clear time

Preheat mode


Stream feeding mode


Border line for 2 in 1 or 4 in 1

Rotation copy

Auto paper select mode

Auto tray switching

Auditing mode

Account number entry

Account number change

Account number deletion

Number of copies per account

Resetting account

Erase width adjustment

Layout in 2 in 1 copy


Offset of paper output tray

Program No.

1

2

3

4

5

6

7

14

15

16

17

8

9

10

11

12

13

18

19

3


● For programs 1 to 9 and 16 to 19, the entered program number will be steadily lit on the left side of the copy quantity display and the currently selected parameter number for the program will blink on the right side.

● For programs 10 to 15 (programs for auditing accounts), the display varies with the program number. See page 39 for setting programs 10 to 15.

37

USER PROGRAMS

4

Select the desired parameter using the numeric keys.

● The entered parameter number will blink on the right side of the copy quantity display.

● The parameters are shown in the table below.

For example, to change the setting of the auto power shut-off timer to

60 min., press key 2.

Program name

Auto clear time

Preheat mode


Parameters

0 e OFF

5 e 10 sec.

0 e OFF

* 1 e 30 min.

Stream feeding mode


* 0 e OFF

0 e OFF

Border line for 2 in 1 or 4 in 1 * 0 e OFF

1 e 30 sec.

1 e 30 sec.

2 e 60 min.

1 e ON

* 1 e ON

1 e ON

Rotation copy

Auto paper select mode

Auto tray switching

Erase width adjustment



Offset of paper output tray

0 e OFF

0 e OFF

0 e OFF

0 e 0 mm

* 1 e Pattern 1 2 e Pattern 2

* 1 e Pattern 1

* 1 e ON

* 1 e ON

* 1 e ON

1 e 5 mm

2 e Pattern 2

0 e Upper OFF, lower OFF

2 e Upper ON, lower OFF

* 2 e 60 sec.

2 e 60 sec.

3 e 90 min.

* 2 e 10 mm

3 e 90 sec.

* 3 e 90 sec.

4 e 120 min.

3 e 15 mm

3 e Pattern 3 4 e Pattern 4

* 1 e Upper ON, lower ON

3 e Upper OFF, lower ON

4 e 120 sec.

4 e 120 sec.

5 e 240 min.

4 e 20 mm

● Factory default settings are indicated with an asterisk (*). For layout in 2 in 1 copy and 4 in 1 copy, see page 61.

If you select “0” (OFF) in a program, the corresponding function will be disabled.

5


● The right-hand number in the copy quantity display will be steadily lit and the entered value will be stored.

6

To continue with other user programs, press the key and then repeat steps 2 to 5. To exit the user program mode, press the light ( ) key.

All the alarm indicators will go out.

●

38

USER PROGRAMS

Settings for auditing accounts

Settings of user programs No. 10 to 15 varies with the program number. For setting of all programs, first follow steps 1 to 3 in “Setting the user programs” on page 37 to select a program. (1. Press the light ( ) key for more than 5 seconds. 2. Enter a program number (10 to 15) using the numeric keys. 3.

Press the START key.) Then follow the appropriate instructions for the program.

Program No. 10: Auditing mode

If the auditing mode is enabled, copying is limited to operators with an assigned 3-digit account number. A maximum of 20, 3-digit account numbers can be assigned. Use program No. 11 to register account numbers.

When program No. 10 is entered, the current setting (0: OFF, 1:ON) will blink on the right side of the copy quantity display.

1.

Select the desired setting using the numeric keys.

0: OFF

1: ON

2.


● The setting will be stored.

3.

To continue with other user programs, press the key and enter another program number. To exit the user program mode, press the light ( ) key.

Program No. 11: Account number entry

Program No. 11 is used to register accounts. When program No. 11 is entered,

“–––” will blink in the copy quantity display.

● If the number of accounts has reached the upper limit (20), “11E” will appear in the copy quantity display. Press the key. The copier will return to step 2 on page 37.

1.

Enter a 3-digit account number using the numeric keys.

● Any 3-digit number except “000” can be registered as an account number.

2.


● If a number that is already registered or “000” is entered, the number will blink in the copy quantity display.

3.

Repeat steps 1 and 2 for other account numbers.

4.


39

USER PROGRAMS

Program No. 12: Account number change

Program No. 12 is used to change account numbers. When program No. 12 is entered, an account number will appear in the copy quantity display.

● If no account number has been registered, “12E” will appear in the copy quantity display. Press the key. The copier will return to step 2 on page

37.

1.

Use the copy ratio display ( ) key to select the account number to be changed.

● Use the key to advance through the account numbers.

2.


● The account number will be erased and “–––” will blink in the copy quantity display.

3.

Enter a new account number using the numeric keys.

4.


● If a number that is already registered or “000” is entered, the number will blink in the copy quantity display.

5.

Repeat steps 1 to 4 for other account numbers.

6.


Program No. 13: Account number deletion

Program No. 13 is used to delete accounts. When program No. 13 is entered,

“0” will blink on the right side of the copy quantity display.


37.

1.

To delete an individual account, press the 0 key.

To delete all accounts, press key 1.

2.


●

●

If you have pressed the 0 key in step 1, an account number will appear in the copy quantity display. Proceed to step 3.

If you have pressed key 1, all account numbers will be deleted. Proceed to step 5.

3.

Use the copy ratio display ( ) key to select the account number to be deleted.


4.


● The specified account will be deleted.

5.

To continue with other user programs, enter another program number. To exit the user program mode, press the light ( ) key.

40

USER PROGRAMS

Program No. 14: Number of copies per account

Program No. 14 is used to display the total number of copies made against each account number. When program No. 14 is entered, an account number will appear in the copy quantity display.


37.

1.

Use the copy ratio display ( ) key to select the account number.


2.

Press and hold down the 0 key.

● The number of copies made against the specified account number will be displayed. The two higher digits and the three lower digits will appear alternately while the 0 key is pressed.

Example: 1,234 copies

● The upper limit for the number of copies is 49,999. If the number of copies made reaches 50,000, the number will be reset to 0 and counting will start again from 0.

3.

Repeat steps 1 and 2 for other account numbers.

4.

To continue with other user programs, press the key and select another program number. To exit the user program mode, press the light ( ) key.

41

USER PROGRAMS

Program No. 15: Resetting account

Program No. 15 is used to reset all accounts or to reset any desired individual account. When program No. 15 is entered, “0” will blink on the right side of the copy quantity display.

● If no account number has been registered, “15E” will appear in the copy quantity display. Press the key. The copier will return to step 2 on page 37.

1.

To reset an individual account, press the 0 key.

To reset all accounts, press key 1.

2.


●

●

If you have pressed the 0 key in step 1, an account number will appear in the copy quantity display. Proceed to step 3.

If you have pressed key 1, the number of copies against all account numbers will be reset. Proceed to step 5.

3.

Use the copy ratio display ( ) key to select the account number to be reset.


4.


● The number of copies against the specified account number will be reset.

5.

To continue with other user programs, enter another program number. To exit the user program mode, press the light ( ) key.

42

POWER SAVE MODES

The copier has two power save modes to reduce overall power consumption thereby reduce the cost of operation. In addition, these modes conserve natural resources and help reduce environmental pollution. The two power save modes are preheat mode and auto power shut-off mode.

● User programs

The preheat activation time and the auto power shut-off time have been preset at the factory to 90 sec. for preheat mode and 30 min. for auto power shut-off mode. These times can be changed using user programs. It is suggested that you set appropriate times according to the actual usage of the copier.

Preheat mode

When the copier enters the preheat mode, the POWER SAVE indicator will light up and other indicators will remain on or off as before. In this condition, the fuser in the copier is maintained at a lower heat level, thereby saving power. The preheat level is, however, high enough to allow the copier to come to a ready condition or begin copying within 10 seconds after any key input or copier operation such as paper tray operation is performed.

Auto power shut-off mode

When the copier enters the auto power shut-off mode, the POWER SAVE indicator will light up and all other indicators will go out. The auto power shut-off mode saves more power but requires a longer time to warm up before copying can begin.

43

POWER SAVE MODES

Setting the power save modes

The time that elapses before the copier enters a power save mode after any operation is made can be set manually. This time is set with user program No.

2 for the preheat mode and user program No. 3 for the auto power shut-off mode. For these settings, see page 37.

●

●

The copier will enter the preheat mode first and then the auto power shutoff mode after a preset time has elapsed when no copier operation has been made.

If conflicting settings are made with user programs No. 3 and No. 5, the last program set will have priority.

Copying from the preheat mode

Make desired copier selections and press the START key using the normal copying procedure.

●

●

When any key input is made or any other copier operation is made, the

POWER SAVE indicator will start to blink.

When the START key is pressed, the START key indicator will go out and copying will start within 10 seconds. The POWER SAVE indicator will go out when copying starts.

Copying from the auto power shut-off mode

1


● The copier will exit the auto power shut-off mode and the POWER

SAVE indicator will start to blink.

2

Make desired copier selections and press the START key using the normal copying procedure.

It will take approximately 35 seconds for the copier to start copying.

●

However, you can make desired settings and press the START key during warm-up. Copying will start after warm-up is finished.

44

USER MAINTENANCE

Proper care is essential for clean, sharp copies. Please take a few minutes to regularly clean your copier.

Original table and platen cover

Stains or dirt on the original table or platen cover will also be copied. Wipe the original table and platen cover with a soft, clean cloth.

● If necessary, dampen the cloth with water. Do not use thinner, benzene, or similar volatile cleaning agents.

● If an optional single pass feeder is installed, wipe the scanning window on the original table.

Paper feed roller

Bypass tray paper feed roller

If misfeeds occur frequently when feeding postcards, envelopes, thick paper, etc. through the bypass tray, wipe the blue paper feed roller at the feed slot of the bypass tray with a soft, clean cloth dampened with alcohol or water.

Transfer charger

If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean the charger. The cleaning method is described on page 69, TRANSFER CHARGER

CLEANING.

45

46

COPIER TROUBLE?

Problem

Copier does not operate.

● Copier plugged in?

● Power switch ON?

Solution

Plug the copier into a grounded outlet.

See page 8.

● Copy density properly adjusted?

Turn the power switch ON.

See page 14.

See pages 14 and 26.

Copies are too dark or too light.

Blank copies

Copies smear if rubbed.

Striped copies

Paper misfeeds frequently.

● Is the original placed face down?

●

●

Paper too heavy?

Paper damp?

Place the original face down on the original table.

Use copy paper within the specified range.

See page 49.

Replace with dry copy paper.

Be sure to store copy paper in a dry location.

See page 50.

● Is transfer charger clean?

●

●

●

●

Non-standard paper used?

Paper properly installed?

Pieces of paper inside copier?

Paper curled or damp?

Clean the transfer charger.

See page 69.

Use standard paper. If using special paper, feed the paper through the bypass tray.

See pages 18 and 49.

Make sure the paper is properly installed. See pages 10 and 18.

Remove all pieces of misfed paper.

See page 31.

Store copy paper flat in the wrapper in a dry location. See page 50.

COPIER TROUBLE?

Problem

Copies are smudged or dirty.

Paper size for a paper tray cannot be set.

Power is on but copying is not possible.

● Original table or platen cover dirty?

Solution

Clean regularly. See page 45.

● Original smudged or blotchy?

Use a clean original.

● Is the indicator on?

● Is the COPY indicator off?

● Is copying, printing or facsimile printing being performed?

● Is the POWER SAVE indicator blinking?

● Is only the POWER SAVE indicator on?

● Is the COPY indicator off?

● Is steadily lit in the copy quantity display?

● Is the indicator on?

Maintenance is required. Contact your

SHARP service centre as soon as possible.

Use the COPY/FAX key to select the COPY mode. See Note below.

Set the paper size after copying, printing or facsimile printing is complete.

Wait until warm-up is complete.

Warm-up time is approximately 35 seconds.

The copier is in the auto power shut-off mode. Press the START key. See page 43,

POWER SAVE MODES.

Use the COPY/FAX key to select the COPY mode. See Note below.

The copier is in the auditing mode.

Enter your account number using the numeric keys. See page 13.

Copy paper is needed. See page 10,

LOADING COPY PAPER.

COPY/FAX key

The COPY/FAX key is used to switch between the FAX and COPY modes.

For details, see the MULTI ACCESS manual.

47

COPIER TROUBLE?

Problem

Power is on but copying is not possible.

Lighting fixture flickers.

● Is blinking in the copy quantity display?

● Is steadily lit in the copy quantity display?

● Is the indicator blinking?

Solution

The TD cartridge is not installed. Install the

TD cartridge.

Side cover(s) is open.

Close the front and side covers securely.

The TD cartridge must be replaced. See page

27, TD CARTRIDGE REPLACEMENT.

● Is the indicator blinking?

A misfeed has occurred. See page 31,

MISFEED REMOVAL.

● Is the START key indicator blinking?

Toner replenishment takes up to 2 minutes.

Wait until the START key indicator stops blinking.

● Is the same power outlet used for the lighting fixture and the copier?

Connect the copier to a power outlet which is not used for other electric appliances.

Be sure to use only genuine SHARP parts and supplies.

Please contact your SHARP service centre immediately if a problem persists after checking the above.

Self-diagnostic function

An automatic self-diagnostic function is built into the copier. Should the copier malfunction, the self-diagnostic function will locate the problem and stop the copier to prevent damage. An alphanumeric code will appear in the copy quantity display.

Example

Should the copier completely stop and a letter and a number appear alternately, contact your SHARP service centre immediately.

48

SUPPLIES

Types and sizes of copy paper

Size Weight

Paper tray

Bypass tray

A5* to A3

Ordinary paper:

A6 to A3

Envelopes:

International DL

(110 x 220 mm)

International C5

(162 x 229 mm)

Commercial 10

(4-1/8" x 9-1/2")

56 to 80 g/m 2

56 to 128 g/m 2 **

(Ordinary paper)

* A5 copy paper can be used in the uppermost paper tray but cannot be used in other trays (in optional paper feed units).

** For paper weighing from 105 to 128 g/m 2 , A4 is the maximum size that can be fed through the bypass tray.

*** Do not use envelopes that have metal clasps, plastic snappers, string closures, windows, linings, self-adhesive patches or synthetic materials.

These will cause physical damage to the copier.

●

●

For best results, use only paper recommended by SHARP.

Special papers except envelopes must be fed one sheet at a time through the bypass tray. Up to 10 envelopes can be set at one time.

Capacity (80 g/m 2 Special paper paper)

250 sheets

100 sheets Transparency film, labels, envelopes***

49

SUPPLIES

Genuine supplies statement

Standard supplies for this copier that are to be replaced by the user are copy paper, TD cartridge, and drum cartridge.


SHARP products.

Only genuine SHARP consumables carry the Genuine Supplies label.


Proper storage

1.

Store the supplies in a location that is:

●

●

● clean and dry, at a stable temperature, not exposed to direct sunlight.

2.

Store copy paper in the wrapper and lying flat.

● Paper stored out of the wrapper or in packages standing on end may curl or get damp, resulting in paper misfeeds.

50

SPECIFICATIONS

Type

Copy system

Originals

Original sizes

Copy sizes

Copying speed

(at 100% copy ratio)

Continuous copy

First-copy time

Warm-up time

Copy ratio

Exposure system

Copy paper feed

Fusing system

Developer system

Light source

Resolution

Gradation

Power supply

Power consumption

Digital copying machine, desktop

Dry, electrostatic transfer

Sheets, bound documents

Max. A3

Max. A3

Min. A6

Image loss: Max. 4 mm (leading and trailing edges)

Max. 4 mm (along other edges in total)

16 copies/min. (A4)

12 copies/min. (A4R)

10 copies/min. (B4)

9 copies/min. (A3)

Max. 99 copies; subtractive counter

7.2 sec. (except in a power save mode)

Approx. 35 sec.

Variable: 50% to 200%, in 1% increments (total 151 steps)

Fixed preset: 50%, 70%, 81%, 86%, 100%, 115%, 122%,

141%, 200%

Moving optical source, slit exposure (stationary platen) with automatic exposure function

One paper tray with automatic feed (250 sheets), one bypass tray with automatic feed (100 sheets)

Heat rollers

Magnetic brush development

Xenon lamp

Scan: 400 dpi

Output: 600 dpi

Scan: 256 levels

Output: 2 levels

AC 230V, 50 Hz, 6 amperes

Max. 1.5 kW

51

52

SPECIFICATIONS

Overall dimensions

(with bypass tray folded)

Weight

590 mm (W) x 531 mm (D)

Copier dimensions

Operating conditions

Optional equipment

Approx. 32 kg

TD and drum cartridges included

590 mm (W) x 531 mm (D) x 470 mm (H)

Temperature: 15°C to 30°C (59°F to 86°F)

Humidity: 20% to 85%

Single pass feeder (AR-SP2)

Electronic sorting kit (AR-EB3)

250-sheet paper feed unit (AR-DE5)

2x250-sheet paper feed unit (AR-DE6)

Facsimile expansion kit (AR-FX2)

Printer expansion kit (AR-PB8)

PS2 expansion kit (AR-PS1)

LCD panel kit (AR-PA1)

Job separator tray kit (AR-TR2)

First-copy time may differ depending on operating conditions, such as power-supply voltage and room temperature.

As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

OPTIONAL

EQUIPMENT

CONTENTS

●

●

●

●

Page

SYSTEM CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

SINGLE PASS FEEDER (AR-SP2) . . . . . . . . . . . . . . . . . . . . . . 55

● Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

●

●

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Using the SPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

● Misfeed removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

ELECTRONIC SORTING KIT (AR-EB3) . . . . . . . . . . . . . . . . . . 58

●

●

●

●

Rotation copying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Sort/group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

2 in 1 or 4 in 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

● Margin shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

250-SHEET PAPER FEED UNIT (AR-DE5)/

2x250-SHEET PAPER FEED UNIT (AR-DE6) . . . . . . . . . . . . . . 66

53

SYSTEM CONFIGURATION

A number of options are available for the copier which allow you to configure a copier system to meet your particular needs. The options include the following.

Single pass feeder

(AR-SP2)

Electronic sorting kit (AR-EB3)

Facsimile expansion kit (AR-FX2)*

Printer expansion kit (AR-PB8)*

PS2 expansion kit (AR-PS1)*

LCD panel kit (AR-PA1)*

Job separator tray kit (AR-TR2)*

* These options are not used for the copier operation. For description of these options, see their separate manuals.

54

250-sheet paper feed unit

(AR-DE5)

2x250-sheet paper feed unit

(AR-DE6)

SINGLE PASS FEEDER (AR-SP2)

The single pass feeder (SPF) holds up to 30 originals for automatic feeding.

PART NAMES

Original guides

Document feeder tray Left feeding roller cover

Exit area Right feeding roller cover

Specifications

Acceptable originals

Weight: 56 to 90 g/m 2

Size: A5 to A3

Capacity: Up to 30 sheets provided the total aggregate thickness does not exceed 4 mm

Detectable original A5, A4, A4R, B4, A3 sizes

Power supply

Weight

Dimensions

Drawn from the copier

Approx. 5.3 kg

583 mm (W) x 435 mm (D) x 131 mm (H)


55


Using the SPF

●

●

●

Be sure to remove any staples or paper clips from the originals.

Damaged or crumpled originals may misfeed in the SPF.

It is recommended that these originals be copied from the original table.

For best feeding of originals which have binding holes punched into them, insert them so that the holes are positioned to the right or along the side guides.

●

●

Special originals such as transparency film and tracing paper should not be fed through the SPF but should be copied from the original table.

Image loss (max. 4 mm) can occur at the leading and trailing edges of the copies. Also image loss (max. 4 mm in total) can occur along the other edges of the copies.

Stream feeding mode

If the stream feeding mode has been enabled using user program

No. 4, the SPF indicator will continue to blink for approximately 5 seconds after feeding of all originals is completed. While this indicator is blinking, any new originals placed in the SPF will be fed and copied automatically. See page 36, USER PROGRAMS.

1

Ensure that no original is left on the original table.

2

Adjust the original guides to the size of the originals.

3

Set the originals face up in the document feeder tray.

● The SPF indicator will light up. If this indicator does not light up, the originals are not properly set or the SPF is not properly closed.

4

Ensure that the copy paper size in the paper tray is the same size as the originals.

If an optional paper feed unit is installed, a paper tray with the ● corresponding paper size will be automatically selected.

5


● Since only one copy per original can be made, the number of copies cannot be changed. However, if an optional electronic sorting kit is installed, a multiple number of copies can be set using the numeric keys.

Press the CLEAR key to stop copying in the middle of a run.

●

While making copies from the SPF, do not place originals of the next copying job. Place them after all copies of the current job have been output.

56


Misfeed removal

A

C

Location A

Left feeding roller cover

B

If an original misfeed occurs in the SPF, the copier will stop and the red indicator which indicates an original misfeed will blink.

1

Open the left feeding roller cover and pull the original gently to the left and out from the document feeder tray.

Close the left feeding roller cover.

Location B

Right feeding roller cover

2

If the misfed original cannot be removed in step 1, open the right feeding roller cover and remove the misfed original. Close the right feeding roller cover.

Location C

Roller

3

If the misfed original cannot be removed in steps 1 and

2, remove the misfed original from the exit area. Open the document feeder cover and rotate the roller in the direction indicated by the arrow if needed.

If the misfed original cannot be easily removed from the exit area, open the front part of the document feeder tray to remove the original.

4

Open and close the document feeder cover to cancel the misfeed location indicator.

After misfed originals are removed, a number may appear in the copy quantity display, indicating the number of originals that must be returned to the document feeder tray. Return the originals and press the START key to resume copying.

57

ELECTRONIC SORTING KIT (AR-EB3)

If an electronic sorting kit (AR-EB3) is installed, the copier can perform several additional useful functions. These functions are 2 in 1 and 4 in 1, erase, margin shift, and sort/group functions. Also, rotation copying can be performed and a multiple number of originals can be scanned and stored into the memory. The memory can be expanded by adding commercially available memories recommended by SHARP. For details, contact your dealer.

To use the 2 in 1 or 4 in 1 and sort/group functions, an optional single pass feeder (AR-SP2) is needed. When installing an electronic sorting kit, it is recommended to install a single pass feeder.

Rotation copying

If user program No. 7 is set, the image of the original will rotate when the orientation of the original does not match that of the copy paper. Rotation copying will function only if the auto paper select mode or auto copy ratio mode has been selected. Even if user program No. 7 is not set, rotation copying will function when the 2 in 1 or 4 in 1 function is selected. See page

37. However, if enlargement copying onto a paper size larger than A4 is performed, the image cannot be rotated.

When this occurs, the detected size and orientation of the original will be indicated by a steadily lighted indicator and a flashing indicator will show the required orientation of the original. The original must be rotated 90° to match the flashing indicator to prevent image loss on the copies.

Example: Copying from an A3 original onto A4 paper

Copy

Original Paper

58


Sort/group

If an optional electronic sorting kit is installed, the copier will have two sorter modes for different copying jobs: one sorts copies into sets matching the sequence of the originals and the second groups copies by originals.

The sort/group feature cannot be used with the dual page copy feature.

To change the SORT/GROUP mode, press the SORT/GROUP key to select the desired mode.

● The capacity of the paper output tray is 250 sheets (150 sheets if an optional job separator tray kit (AR-TR2) is installed). When the number of copies output reaches this limit in a sort or a group copy run, copying will stop, the output tray full ( ) indicator will light and the START key indicator will blink.

Remove the copies from the paper output tray and press the START key to resume copying.

1

2

3

1

2

3

1

2

3

1

2

3

Sort mode

Each set of copies will be sequentially delivered to the paper output tray.

1

2

3

2

2

2

1

1

1

3

3

3

Group mode

All copies of the same originals will be grouped in the paper output tray.

Offset mode

1

2

3

1

1

1

1

1

2

Non-offset mode

1

2

3

1

1

Offset stack (AR-161 only)

If the offset stack mode is enabled using user program

No. 19, each copy will be offset by approximately 25 mm.

When copying in the sort mode, each collated set of copies will be stacked offset from the previous set.

When copying in the group mode, copies will be offset and stacked in groups of multiple copies from the same original.

If the offset stack mode is disabled, copies will not be offset.

The offset stack mode is enabled in the factory default setting.

59


Copying in the sort mode

When copying in the sort mode, the original image will be stored in the copier memory each time an original is scanned and copying will start after all originals have been scanned. To copy in the sort mode, an optional single pass feeder (AR-SP2) is needed.

1


● The original table cannot be used for sort copying.

2

Press the SORT/GROUP key to select the SORT mode.

3

Ensure that the copy paper size in the paper tray is the same size as the originals.

If an optional paper feed unit is installed, a paper tray with the ● corresponding paper size will be automatically selected.

4


● Copying will start after the originals have been scanned. Up to 30 sheets of A4 originals can be scanned. (If originals are fed continuously using the stream feeding mode, up to approximately 60 sheets of

A4 originals can be scanned. However, when copying originals which require more memory such as photographs, the number of originals which can be scanned will be less.) When the memory becomes full of scanned original image data, the ORIGINAL DATA indicator will blink.

When the ORIGINAL DATA indicator blinks, the copier will stop scanning. To start copying of scanned originals, press the START key.

To cancel copying, press the CLEAR or CLEAR ALL key.

60

2 in 1 or 4 in 1

2 in 1 copying

Pattern Pattern


The 2 in 1 or 4 in 1 feature is used to copy 2 or 4 originals, collectively in a specified order, onto one sheet.

To use these features, an optional single pass feeder (AR-SP2) is needed.

●

●

These features cannot be used with the dual page copying, XY zoom, erase, or margin shift features.

Copies can be made with or without the border lines shown in the illustration. See USER PROGRAMS on page 36.

●

●

The order of originals which will be arranged on the copies can be selected by user programs. There are two patterns of layout for 2 in 1 copying and four patterns of layout for 4 in 1 copying. See page 36.

The 2 in 1 or 4 in 1 feature operates only in the sort or group mode. If the

2 in 1 or 4 in 1 feature is selected when either the sort or group mode has not been selected, the group mode will be automatically selected.

Pattern

4 in 1 copying

Pattern

Pattern Pattern Pattern Pattern

1


● The original table cannot be used for the 2 in 1 or 4 in 1 feature.

2

Use the TRAY SELECT key to select the paper tray with the desired paper size.

The bypass tray and any tray with non-standard size paper cannot be ● used with the 2 in 1 or 4 in 1 feature.

3

To confirm or set the layout pattern for 2 in 1 copying, first ensure that both the 2 IN 1 and 4 IN 1 indicators are not lit then press and hold the 2 IN 1 / 4 IN 1 key for more than 5 seconds.

● The 2 IN 1 indicator will blink and the currently selected layout pattern number will blink in the copy quantity display.

●

To confirm or set the layout pattern for 4 in 1 copying, use the 2 IN 1 / 4 IN 1 key to light the 2 IN 1 indicator then press and hold the 2 IN 1 / 4 IN 1 key for more than 5 seconds.

The 4 IN 1 indicator will blink and the currently selected layout pattern number will blink in the copy quantity display.

61


62

4

Enter the desired pattern number using a numeric key.

● The entered number will blink in the copy quantity display. For layout pattern numbers, see the previous page.

5


● The entered number will light up steadily.

6

Press the 2 IN 1 / 4 IN 1 key to complete the selection.

● The copy ratio will be calculated automatically. If the calculated copy ratio is less than 50%, part of original image may not be copied because the smallest copy ratio is 50%.

7


8


● Copying will start after the originals have been scanned. Up to 30 sheets of A4 originals can be scanned. (If originals are fed continuously using the stream feeding mode, up to approximately 60 sheets of A4 originals can be scanned. However, if photographs are copied, the number of originals which can be scanned is less.) When the memory becomes full of scanned original image data, the ORIGINAL DATA indicator will blink.

When the ORIGINAL DATA indicator blinks, the copier will stop scanning. To start copying of scanned originals, press the START key.

To cancel copying, press the CLEAR or CLEAR ALL key.

Erase

Edge erase

A A

Centre erase

A B A B

Edge + Centre erase

A B A B


This copier has an edge erase mode and a centre erase mode.

● Edge erase can be used to eliminate shadow lines around the edges of copies caused when thick paper or a book is used as an original.

●

●

●

●

Centre erase can be used to eliminate the shadow produced by the bindings of bound documents.

Edge + centre erase can be used to eliminate shadow lines around the edges of copies and to eliminate the shadow at the centre of copies.

The erase width can be set from 0 to 20 mm in five steps using user program No. 16. See page 36.

This feature cannot be used with the 2 in 1 or 4 in 1 feature.

1


If an optional single pass feeder (SPF) is installed, it can also be used ● for this feature.

2

Press the ERASE key to select the desired erase mode.

● To select the EDGE + CENTRE ERASE mode, press the ERASE key until both the EDGE and CENTRE indicators light up.

3


● If non-standard size paper or the bypass tray is used, the paper will be regarded as A3 size paper and the erase area will not be proper if the paper size is not A3.

● If an optional paper feed unit is installed, use the TRAY SELECT key to select the desired paper size.

63


4


5


64


Margin shift

Original Copy

The MARGIN SHIFT feature automatically shifts the text or image to the right to increase the left margin by approximately 9 mm.

● This feature cannot be used with the 2 in 1 or 4 in 1 feature.

Expanded margin

Margin is expanded here.

1


● If an optional single pass feeder (SPF) is installed, it can also be used for this feature. Set the originals so that the margin side is positioned at the left side.

2

Press the MARGIN SHIFT key.

3


● If an optional paper feed unit is installed, use the TRAY SELECT key to select the desired paper size.

4


65

250-SHEET PAPER FEED UNIT (AR-DE5)

2x250-SHEET PAPER FEED UNIT (AR-DE6)

These paper feed units provide the convenience of increased paper capacity for the copier and a greater choice of paper sizes readily available for copying.

The AR-DE5 contains one 250-sheet paper tray and the AR-DE6 contains two 250-sheet paper trays.

PART NAMES

AR-DE5 AR-DE6

Side cover Side cover

Tray Trays

Loading copy paper

The method of loading copy paper for the paper trays of these paper feed units is the same as for the paper tray in the copier. See page 10.

The method of changing the copy paper size is also the same for the paper tray in the copier. See page 11.

66

250-SHEET PAPER FEED UNIT (AR-DE5)/2x250-SHEET PAPER FEED UNIT (AR-DE6)

Misfeed removal

The copier will stop when a misfeed occurs. The misfeed ( ) indicator and the red indicator which indicates the paper feed unit will blink.

1

Open the side cover of the paper feed unit and remove the misfed paper.

● Be sure to perform this step before pulling out the paper trays. If not, the paper may be torn as the trays are opened.

2

Gently lift and pull out the paper tray which was in use.

Remove any misfed paper.

3

Close the paper tray and the side cover.

● Confirm that the misfeed ( ) indicator has gone out.

67

250-SHEET PAPER FEED UNIT (AR-DE5)/2x250-SHEET PAPER FEED UNIT (AR-DE6)

Specifications

AR-DE5

Copy paper size

Paper weight

Paper capacity

Weight

Dimensions

Power supply

A4 to A3

56 to 80 g/m 2

One paper tray with capacity for 250 sheets of paper

Approx. 4.7 kg

590 mm (W) x 471 mm (D) x 88 mm (H)


AR-DE6

Copy paper size

Paper weight

Paper capacity

Weight

Dimensions

Power supply

A4 to A3

56 to 80 g/m 2

Two paper trays with capacity for 250 sheets of paper each

Approx. 9.1 kg

590 mm (W) x 471 mm (D) x 173.5 mm (H)



68

TRANSFER CHARGER CLEANING

If copies start becoming streaky or blotchy, the transfer charger may be dirty.

Clean the charger using the following procedure.

1

Turn the power switch off.

2


Charger cleaner

3

Gently lift and pull out the paper tray and take the charger cleaner out by holding the tab.

4

Set the charger cleaner onto the transfer charger and gently slide the cleaner in the direction indicated by the arrow two or three times.

Slide the charger cleaner from one end to the other end along the groove of the transfer charger. If the cleaner is stopped on the way, smudges on copies may occur.

● If the white sheet metal is smudged with toner, wipe it with a soft, clean cloth.

5

Return the charger cleaner to its original position.

Close the paper tray. Close the side cover by pressing the handle on the cover.

6

Turn the power switch on.

69

DRUM CARTRIDGE LIFE

To find out how many more copies can be made before the 30,000 mark is reached, follow the procedure described below.

1

Press and hold the light ( ) key for more than 5 seconds until all the alarm indicators ( , , , , and ) blink and “– –” appears in the copy quantity display.

2

Press and hold down the CLEAR key for more than 5 seconds to find out how many more copies can be made.

● The number will appear in two steps, each with three digits.

Example: 1,234 copies can be made before the next drum cartridge replacement.

3

Press the light ( light up.

) key. The START key indicator will

This procedure is not available in the FAX mode.

See Note on page 47.

70

INDEX

2

250-sheet paper feed unit . . . . . . . . . . . . . . . . . . . . . . . 66

2 in 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

2x250-sheet paper feed unit . . . . . . . . . . . . . . . . . . . . . 66

4

4 in 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

A

Auto clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Automatic exposure adjustment . . . . . . . . . . . . . . . . . . 26

Auto power shut-off mode . . . . . . . . . . . . . . . . . . . . . . 43

B

B/W reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Bypass tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

C

Cautions on handling . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Copier trouble? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Copying

– large original . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

– normal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

– reduction/enlargement . . . . . . . . . . . . . . . . . . . . . . . . 16

– through bypass tray . . . . . . . . . . . . . . . . . . . . . . . . . . 18

– two-sided . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Copy paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 49

Copy quantity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Copy ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

D

Dark key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Drum cartridge

– indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

– life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

– replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Dual page copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

E

Electronic sorting kit . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Enlargement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Exposure adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 14

F

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Fixed copy ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Fusing unit release lever . . . . . . . . . . . . . . . . . . . . . . . . 33

G

Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

I

Initial settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

L

Light key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 37

Loading copy paper . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

M

Maintenance

– user maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

– maintenance required indicator . . . . . . . . . . . . . . . . . 35

Manual exposure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Manual feeding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Margin shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Misfeed removal

– bypass tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

– in the copier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

– paper tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34, 67

– SPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

N

Names

– operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

– part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

O

Operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Original table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

P

Paper

– loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

– special . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

– specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Paper output tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Paper size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Paper tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Photo mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Platen cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Power on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Power save modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Power switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Preheat mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

R

Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Replacement

– drum cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

– TD cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

71

INDEX

S

Single pass feeder (SPF) . . . . . . . . . . . . . . . . . . . . . . . . 55

Sort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Special paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Specifications

– copier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

– paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

SPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Status indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Storage of supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

T

TD cartridge replacement . . . . . . . . . . . . . . . . . . . . . . . 27

Total output count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Two-sided copying . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

U

User maintenance

– bypass tray paper feed roller . . . . . . . . . . . . . . . . . . . 45

– original table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

– platen cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

– transfer charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

X

XY zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Z

Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

72

S H A R P

Date Issued:Nov. 1, 1998

MATERIAL SAFETY DATA SHEET

MSDS No. F-00841

Section 1.

Product Identification

Product:

AR-200DC/AR-200LT (Black Toner)

Section 2.

Supplier’s Name and Address

Sharp Corporation

22-22 Nagaike-cho, Abeno-ku, Osaka, Japan

Local suppliers are listed below. Please contact the nearest supplier for additional information.

(Country)

U.S.A.

Canada

United Kingdom

(Name and Telephone Number)

Sharp Electronics Corporation

Telephone number for information: 1-800-237-4277

Emergency telephone number: 1-800-255-3924

Sharp Electronics of Canada Ltd.

Telephone number for information: 905-890-2100


Sharp Electronics (U.K.) Ltd.

Telephone number for information: 01923-474013

Section 3.

Ingredients

Ingredients

Styrene-Acrylate copolymer

Carbon black

Iron oxide

Metal Complex dye

CAS No.







29497-14-1

1333-86-4

1309-38-2

109125-51-1

109125-50-0

84179-66-8

Proportion OSHA PEL

> 88 %

< 6.0%

< 4.5%

< 1.5%

Not listed

3.5mg/m

Not listed

0.5mg/m

3

3

ACGIH TLV Other Limits

Not listed

3.5mg/m 3

Not listed

0.5mg/m 3

None

None

None

None

Section 4.

Hazardous Identification (Emergency Overview)

Toner is a fine, black powder possessing no immediate hazard. There are no anticipated carcinogenic effects from exposure based on animal tests performed using toner. When used as intended according to instructions, studies do not indicate any symptoms of fibrosis will occur.

Section 5.

Health Hazard Data

Route(s) of Entry: Inhalation?

Yes

Skin?

No

Ingestion?

Possible but very unusual.

Health Hazards: Acute oral toxicity ------- LDL

0

of this toner is over 2,000mg/kg.

Mutagenicity -------------- The result of Ames test is negative.

Carcinogenicity: In 1996 the IARC reevaluated carbon black as a Group 2B carcinogen (possible human carcinogen). This classification is given to chemicals for which there is inadequate human evidence, but sufficient animal evidence on which to base an opinion of carcinogenicity. The classification is based upon the development of lung tumors in rats receiving chronic inhalation exposures to free carbon black at levels that induce particle overload of the lung. Studies performed in animal models other than rats did not show any association between carbon black and lung tumors. Moreover, a two-year cancer bioassay using a typical toner preparation containing carbon black demonstrated no association between toner exposure and tumor development in rats.

Chronic Effect: In a study in rats of chronic inhalation exposure to a typical toner, a mild to moderate degree of lung fibrosis was observed in 92% of the rats in the high concentration (16mg/m 3 ) exposure group, and a minimal to mild degree of fibrosis was noted in 22% of the animals in the middle

(4mg/m 3 ) exposure group, but no pulmonary change was reported in the lowest (1mg/m 3 ) exposure group, the most relevant level to potential human exposures.

Signs and Symptoms of Exposure: Minimal irritation to respiratory tract may occur as with exposure to any non-toxic dust.

Medical Conditions Generally Aggravated by Exposure: None

Emergency and First Aid Procedures:

Inhalation; Remove to fresh air. If effects occur, consult medical personnel.

Eye; In case of contact, immediately flush eyes with water for 15 minutes.

73

Section 6.

Physical Chemical Characteristics

Boiling / Melting Point: Not applicable

Vapor Pressure: Not applicable

Vapor Density:

Evaporation Rate:

Not applicable

Not applicable

Appearance:

Odor:

Fine powder

Odorless

Specific Gravity: 1.1

Solubility in Water: Negligible

PH:

Viscosity:

Color:

Not applicable

Not applicable

Black

Section 7.

Fire and Explosion Data

Flash Point (Method Used):

Ignition Temperature:

Flammable Limits:

Extinguishing Media:

Special Fire Fighting Procedure:

Not applicable

>350°C

(LEL); Not applicable

CO

2

, dry chemical, foam or water

None

(UEL); Not applicable

Unusual Fire and Explosion Hazard: This material has no unusual fire or explosion hazards.

Sensitivity to Mechanical Impact:

Sensitivity to Static Charge:

None

None

Section 8.

Reactivity Data

Stability: Stable

Incompatibility (Material to Avoid): None

Hazardous Decomposition:

Hazardous Polymerization:

CO and NOx

Will not occur.

Section 9.

Precautions for Safe Handling and Use

Personal Protection Information (Respiratory, Eye Protection and Protective Glove):

Use of a dust mask is recommended when handling a large quantity of toner or during long term exposure, as with any non-toxic dust.

Engineering Control / Ventilation: Not required.

Work / Hygienic Practice: Inhalation should be minimized as with any non-toxic dust.

Steps to be taken in case of Spill or Leak: Sweep up or clean up with vacuum cleaner.

Waste Disposal Method: Waste material may be dumped or incinerated under conditions which meet all federal, state and local environmental regulations.

Section 10. Regulatory Information

NFPA Rating (U.S.A.):

WHMIS Legislation (Canada):

Transport Information:

UN No.:

Health = 1 Flammability = 1

This product is not a controlled product.

This product is not a hazardous material.

None allocated.

Reactivity = 0

Section 11. Other Information

References: IARC (1996) IARC Monographs on the Evaluation of the Carcinogenic Risk of Chemicals to Humans,

Vol. 65, Printing Process and Printing inks, Carbon Black and Some Nitro Compounds, Lyon, pp-

149-261

H. Muhle, B. Bellmann, O. Creutzenberg, C. Dasenbrock, H. Ernst, R. Kilpper, J. C. MacKenzie,

P. Morrow, U. Mohr, S. Takenaka, and R. Mermelstein (1991) Pulmonary Response to Toner upon

Chronic Inhalation Exposure in Rats. Fundamental and Applied Toxicology 17, pp. 280-299

74

S H A R P

Date Issued :Nov. 1, 1998

MATERIAL SAFETY DATA SHEET

MSDS No. F-30841

Section 1.

Product Identification

Product

AR-200DC/AR-200LD (Black Developer)

Section 2.

Supplier’s Name and Address

Sharp Corporation

22-22 Nagaike-cho, Abeno-ku, Osaka, Japan

Local suppliers are listed below. Please contact the nearest supplier for additional information.

(Country)

U.S.A.

Canada

United Kingdom

(Name and Telephone Number)

Sharp Electronics Corporation

Telephone number for information: 1-800-237-4277


Sharp Electronics of Canada Ltd.

Telephone number for information: 905-890-2100


Sharp Electronics (U.K.) Ltd.

Telephone number for information: 01923-474013

Section 3.

Ingredients

Ingredients

Iron powder

Styrene-Acrylate copolymer

Carbon black

CAS No.

7439-89-6

29497-14-1

1333-86-4

Proportion OSHA PEL

> 92.5%

< 7.0%

< 0.5%

Not listed

Not listed

3.5mg/m 3

ACGIH TLV Other Limits

Not listed

Not listed

3.5mg/m 3

None

None

None

Section 4.

Hazardous Identification (Emergency Overview)

Developer is a black powder containing small amounts of toner, and possessing no immediate hazard.

There are no anticipated carcinogenic effects from exposure based on animal tests performed using toner.

Section 5.

Health Hazard Data

Route(s) of Entry: Inhalation?

No

Skin?

No

Ingestion?

Possible but very unusual.

Health Hazards: Acute oral toxicity ----------- LDL

0

of this toner which is included in this developer is over

2,000mg/kg.

Mutagenicity ------------------ The toner, which is included in this developer, has been tested on

Ames test. The result is negative.

Carcinogenicity: In 1996 the IARC reevaluated carbon black as a Group 2B carcinogen (possible human carcinogen). This classification is given to chemicals for which there is inadequate human evidence, but sufficient animal evidence on which to base an opinion of carcinogenicity. The classification is based upon the development of lung tumors in rats receiving chronic inhalation exposures to free carbon black at levels that induce particle overload of the lung. Studies performed in animal models other than rats did not show any association between carbon black and lung tumors.

While there have been no studies to date using developer, a two-year cancer bioassay using a typical toner preparation containing carbon black (a small amount of toner is included in the developer mixture) demonstrated no association between toner exposure and tumor development in rats.

Signs and Symptoms of Exposure: Minimal irritation to respiratory tract may occur as with exposure to any non-toxic dust.

Medical Conditions Generally Aggravated by Exposure: None

Emergency and First Aid Procedures:

Inhalation; Remove to fresh air. If effects occur, consult medical personnel.

Eye; In case of contact, immediately flush eyes with water for 15 minutes.

75

Section 6.

Physical Chemical Characteristics

Boiling / Melting Point: Not applicable

Vapor Pressure: Not applicable

Vapor Density:

Evaporation Rate:

Not applicable

Not applicable

Appearance:

Odor:

Fine powder

Odorless

Specific Gravity: about 7.3

Solubility in Water: Negligible

PH:

Viscosity:

Color:

Not applicable

Not applicable

Black

Section 7.

Fire and Explosion Data

Flash Point (Method Used):

Ignition Temperature:

Flammable Limits:

Extinguishing Media:

Special Fire Fighting Procedure:

Not applicable

>350°C

(LEL); Not applicable

CO

2

, dry chemical, foam or water

None

(UEL); Not applicable

Unusual Fire and Explosion Hazard: This material has no unusual fire or explosion hazards.

Sensitivity to Mechanical Impact:

Sensitivity to Static Charge:

None

None

Section 8.

Reactivity Data

Stability: Stable

Incompatibility (Material to Avoid): None

Hazardous Decomposition:

Hazardous Polymerization:

CO and NOx

Will not occur.

Section 9.

Precautions for Safe Handling and Use

Personal Protection Information (Respiratory, Eye Protection and Protective Glove):

None required under normal use.

Engineering Control / Ventilation:

Work / Hygienic Practice:

Not required.

Not required.

Steps to be taken in case of Spill or Leak: Sweep up or clean up with vacuum cleaner.

Waste Disposal Method: Waste material may be dumped or incinerated under conditions which meet all federal, state and local environmental regulations.

Section 10. Regulatory Information

NFPA Rating (U.S.A.):

WHMIS Legislation (Canada):

Transport Information:

UN No.:

Health = 1 Flammability = 1

This product is not a controlled product.

This product is not a hazardous material.

None allocated.

Reactivity = 0

Section 11. Other Information

References: IARC (1996) IARC Monographs on the Evaluation of the Carcinogenic Risk of Chemicals to Humans,

Vol. 65, Printing Process and Printing inks, Carbon Black and Some Nitro Compounds, Lyon, pp-

149-261

H. Muhle, B. Bellmann, O. Creutzenberg, C. Dasenbrock, H. Ernst, R. Kilpper, J. C. MacKenzie,

P. Morrow, U. Mohr, S. Takenaka, and R. Mermelstein (1991) Pulmonary Response to Toner upon

Chronic Inhalation Exposure in Rats. Fundamental and Applied Toxicology 17, pp. 280-299

76

Warning!

This product is a class A product.

If it is operated in households, offices or similar surroundings, it can produce radio interferences at other appliances, so that the user has to take adequate countermeasures.

CLASS 1 LASER PRODUCT

LASER KLASSE 1

LUOKAN 1 LASERLAITE

KLASS 1 LASERAPPARAT

VAROITUS!

LAITTEEN KÄYTTÄMINEN

MUULLA KUIN TÄSSÄ

KÄYTTÖOHJEESSA MAINITULLA

TAVALLA SAATTAA ALTISTAA

KÄYTTÄJÄN

TURVALLISUUSLUOKAN 1

YLITTÄVÄLLE

NÄKYMÄTTÖMÄLLE

LASERSÄTEILYLLE.

VARNING

OM APPARATEN ANVÄNDS PÅ

ANNAT SÄTT ÄN I DENNA

BRUKSANVISNING

SPECIFICERATS, KAN

ANVÄNDAREN UTSÄTTAS FÖR

OSYNLIG LASERSTRÅLNING,

SOM ÖVERSKRIDER GRÄNSEN

FÖR LASERKLASS 1.

Laserstrahl

CAUTION

VORSICHT

ADVARSEL

INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED.

AVOID EXPOSURE TO BEAM.

UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET UND

SICHERHEITSVERRIEGELUNG ÜBERERÜCKT. NICHT DEM STRAHL AUSSETZEN.

USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE ER

UDE AF FUNKTION. UNDGA UDSAETTELSE FOR STRÅLING.

ADVERSEL USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG SIKKERHEDSLÅS BRYTES.

UNNGÅ EKSPONERING FOR STRÅLEN.

VARNING

VARO!

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRRAR ÄR

URKOPPLADE. STRÅLEN ÄR FARLIG. BETRAKTA EJ STRÅLEN.

AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTÖNTÄ

LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

CLASS 1

LASER PRODUCT

LASER KLASSE 1

In some areas, the “POWER” switch positions are marked “ I ” and “ ” on the copier instead of “ON” and “OFF”.

The symbol “ ” denotes the copier is not completely de-energized but in a stand-by condition at this “POWER” switch position.

If your copier is so marked, please read “ I” for “ON” and “ ” for “OFF”.

Caution!

For a complete electrical disconnection, pull out the main plug.

The socket-outlet shall be installed near the equipment and shall be easily accessible.

The CE mark logo label is affixed on an equipment in case that the directives described in the above sentence are applicable to the product. (This sentence is not applicable in any country where the above directives are not required.)

AR-160/AR-161

SHARP ELECTRONICS (U.K.) LTD.

Sharp House, Thorp Road, Newton Heath, Manchester

M40 5BE

SHARP CORPORATION

PRINTED IN JAPAN

99E KS

TINSE0169QSZZ

Sharp AR-160 Specifications

MODEL

OPERATION MANUAL

• GETTING STARTED

• MAKING COPIES

• STATUS INDICATORS

• GENERAL INFORMATION

• OPTIONAL EQUIPMENT

• APPENDIX

CAUTIONS

CONTENTS

GETTING STARTED

MAKING COPIES

STATUS INDICATORS

GENERAL INFORMATION

OPTIONAL EQUIPMENT

APPENDIX

INTRODUCTION

Conventions used in this manual

MAIN FEATURES

PART NAMES AND FUNCTIONS

Overall layout

PART NAMES AND FUNCTIONS

PART NAMES AND FUNCTIONS

Operation panel

PART NAMES AND FUNCTIONS

COPIER INSTALLATION

CAUTIONS ON HANDLING

LOADING COPY PAPER

LOADING COPY PAPER

Changing the copy paper size in the tray

LOADING COPY PAPER

AUDITING ACCOUNTS

NORMAL COPYING

NORMAL COPYING

How to remove the platen cover

REDUCTION/ENLARGEMENT/ZOOM

Automatic

REDUCTION/ENLARGEMENT/ZOOM

Manual

BYPASS FEED (special paper)

BYPASS FEED (special paper)

TWO-SIDED COPYING

XY ZOOM

XY ZOOM

B/W REVERSE

DUAL PAGE COPY

INTERRUPTING A COPY RUN

AUTOMATIC EXPOSURE ADJUSTMENT

TD CARTRIDGE REPLACEMENT

TD CARTRIDGE REPLACEMENT

DRUM CARTRIDGE REPLACEMENT

DRUM CARTRIDGE REPLACEMENT

MISFEED REMOVAL

Misfeed in the bypass tray

Misfeed in the copier

MISFEED REMOVAL

MISFEED REMOVAL

MISFEED REMOVAL

Misfeed in the paper tray

MAINTENANCE REQUIRED

USER PROGRAMS

List of user programs

USER PROGRAMS

Setting the user programs

USER PROGRAMS

USER PROGRAMS

Settings for auditing accounts

Program No. 10: Auditing mode

Program No. 11: Account number entry

USER PROGRAMS

Program No. 12: Account number change

Program No. 13: Account number deletion

USER PROGRAMS

Program No. 14: Number of copies per account

USER PROGRAMS

Program No. 15: Resetting account

POWER SAVE MODES

POWER SAVE MODES

Setting the power save modes