advertisement
Showpiece
™
and Kit Installation
Manual & User Guide
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Version 10/09
WARNINGS AND NOTICES
NOTICE
•
This game is intended to be operated for amusement purposes only. It is not to be operated in violation of any federal, state, or local laws or regulations. As the owner and/or operator of this game you are responsible for its operation in compliance with such laws and regulations. The factory settings for this game may require adjustment in order to comply with the laws and/or regulations in the jurisdiction where the game is located. It is the sole responsibility of the operator to determine what laws and/or regulations are applicable and to make any adjustments to the game before operating it for its intended purpose.
•
This manual and the information contained within is subject to change without notice.
•
The Showpiece cabinet is intended for use with the Showpiece Integrated Stand (Model 304S).
WARNING
•
Use of unauthorized parts or making any unauthorized modifications will void the warranty and may result in the game operating in an unsafe or incorrect manner.
•
If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
•
This cabinet is not suitable for installation in an area where a water jet would be used. The cabinet must not be cleaned by a water jet.
WARRANTY, REPAIR, AND RETURN POLICY
•
90-day warranty on all electronic components. All warranty periods begin on the date of purchase from Incredible Technologies, Inc.
•
There is a minimum $75.00 service charge for all non-warranty repairs or returns.
•
For all servicing, return to Incredible Technologies, Inc.
•
ANY non-factory repair or attempted repair voids warranty.
RETURN MERCHANDISE AUTHORIZATION
•
All returned merchandise must have a Return Merchandise Authorization (RMA) number marked clearly on the outside of the package.
•
You must obtain all RMA numbers from Incredible Technologies. Please have the product's Cabinet Identification Device (CID) number available when calling for an RMA number.
•
Merchandise returned without an RMA number will not be accepted.
•
Warranty may be void if serial number or security labels are tampered with or removed. Opening the Nighthawk Chassis system will void your
warranty.
•
Advance replacement hardware will be shipped to the customer address on file unless specified otherwise.
•
Advance replacement hardware will be billed to the customer until Incredible Technologies, Inc. receives the returned merchandise, at which time a credit will be issued.
•
All repairs and/or replacements will ship as soon as possible after receipt or request (subject to availability).
PAYMENT FOR AND STORAGE OF REPAIR MATERIALS
•
Materials sent to IT for repair must be paid for according to current price schedules and in a reasonable time. Storage fees for repaired equipment will be charged at a rate of $50.00 (Fifty US Dollars) per calendar month or fraction thereof after 90 (Ninety) days from notice to the customer that the repairs are complete. IT reserves the right to resell repaired equipment to cover accumulated storage charges when the accumulated storage charge reaches 100% (One Hundred Percent) of the repaired items’ then-current replacement cost.
- INCREDIBLE TECHNOLOGIES, INC
GOLDEN TEE® Unplugged, ITS®, INCREDIBLE TECHNOLOGIES®, IT®, ITNet®, and IT incredible TECHNOLOGIES® are the properties of Incredible Technologies, Inc.
All Rights Reserved.
© Copyright 2007-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law. All other marks are the properties of their respective owners. All rights reserved.
TERM SOFTWARE LICENSE
Incredible Technologies, Inc. (“IT,”) hereby offers you (“Licensee”) the right to install and use certain copyrighted computer software produced by IT under the following terms and conditions. This License shall govern the use of the software known as “Golden Tee LIVE 2010” (“Update”) when applied as an update to pre-existing Golden Tee LIVE-equipped hardware (“GT Cabinets”) equipped with an earlier version of the Golden Tee LIVE software
(“Prior Version.”)
1) Term Licensing Fee
The Term Licensing Fee (“TLF”) shall be as follows:
•
As set forth in the periodic payment agreement between IT and Licensee at the time the Term License is purchased. If no TLF is set forth in any such agreement, the TLF shall be equal to the monthly payment set forth in IT's then-current pricing schedule.
2) Term
The license shall be valid on the first date the Update is both installed on a GT Cabinet and authorized by ITNet for play on that GT Cabinet and for thirty
(30) days thereafter. The term shall automatically renew for another thirty (30) days upon the timely payment of the TLF, as agreed upon by the parties, up to a total of twelve (12) complete terms. If the TLF is not paid within fifteen (15) days of the due date, this license shall automatically terminate. At the end of twelve (12) complete terms, this License shall terminate and the parties shall become bound by the terms of the Perpetual Software License attached hereto.
3) License Rights
Licensee shall have the right to utilize the Update on authorized GT Cabinets in the normal course of business and as controlled by the Rules of ITNet, as set forth in a separate “Operator Agreement” document, the terms and conditions of which, where not conflicting with the terms and conditions herein, are hereby incorporated by reference. Updates may only be operated on GT Cabinets which are installed in commercial locations, as that term is defined by IT, and to which there is general access by all parties with a general right to enter the location where the GT Cabinet is operated.
4) Legal Operation
Updates include various features which may not be lawful to operate in any given jurisdiction. No provision of any feature, or its licensure to Licensee under the terms herein shall be deemed as advice that operation of that feature is lawful or not lawful in any given jurisdiction. Licensee shall make reasonable efforts to disable any user-adjustable feature which they know or should have known as not lawful to operate in the location where a GT
Cabinet with an Update is being operated.
5) Termination and Rollback
In the event that this License is terminated for whatever reason, Licensee shall have absolutely no right to operate any GT Cabinet upon which an
Update has been installed. IT reserves the absolute right, at its sole discretion, to terminate the operation of any GT Cabinet upon which an unlicensed
Update has been installed. If Licensee wishes to restore such a GT Cabinet to operating condition without acquiring a new License for the Update, IT will roll-back that GT Cabinet, at no charge to the Licensee, to the Prior Version upon return (at Licensee’s expense) of the required hardware to IT’s service center.
6) Governing Law and Jurisdiction
The validity and construction of this License and of the rights and obligations set forth herein shall be determined and governed by the laws of the State of Illinois. The parties hereby submit to the Jurisdiction of any state or federal court in Cook County Illinois. Licensees operating outside the borders of the United States of America, regardless of their citizenship or residency, explicitly agree to allow any assets they may have in the USA or any other foreign country to be attached, garnished, forfeited or otherwise reached by any legal act if, after due process of law, they are found to be liable to IT for damages by reason of breach of this License.
7) Warranty
If the Licensee discovers any physical defect in the media (disk, EPROM, flash media, etc.) on which the Update is distributed or in the documentation, which in the opinion of Incredible Technologies, Inc. (IT) prevents the product from being used as reasonably intended, IT will replace the media or documentation at no charge. The purchaser must return the item to be replaced, with proof of purchase, to IT within 90 days after taking delivery of the
Update.
8) Disclaimer of Remedies
Acceptance of this License and installation of the Update includes disclaimer and waiver of any and all implied, statutory, or common-law warranties, including warranties of merchantability and fitness for a particular purpose, and limits the purchaser's remedy to returning the Update to IT for replacement.
IT makes no warranty or representation, either express or implied, with respect to Updates, their quality, performance, merchantability, or fitness for a particular purpose. Updates are licensed "as is," and the licensee assumes the entire risk as to their quality and performance other than as explicitly set forth herein.
Acceptance of this License and installation of the Update includes disclaimer and waiver of any and all direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the Update, even if advised of the possibility of such damages. The warranty and remedies set forth above are exclusive and in lieu of all others, oral or written, express or implied. No person, seller, dealer, agent, or employee is authorized to make any modification or addition to this limited warranty.
In jurisdictions which do not allow the exclusion of implied warranties or liability for incidental or consequential damages, acceptance of this License and installation of the Update includes stipulation that the most minimal requirements of the law of those jurisdictions shall govern any additional required additional rights of Licensee.
9) Severability
If any provision of this License shall be held by a court of competent jurisdiction to be illegal, invalid or unenforceable, the parties nevertheless agree that the court should endeavor to give effect to the parties' intentions as reflected in the provision, and the remaining provisions shall remain in full force and effect.
GOLDEN TEE® Unplugged, ITS®, INCREDIBLE TECHNOLOGIES®, IT®, ITNet®, and IT incredible TECHNOLOGIES® are the properties of Incredible Technologies, Inc.
All Rights Reserved.
© Copyright 2007-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law. All other marks are the properties of their respective owners. All rights reserved.
PERPETUAL SOFTWARE LICENSE
Incredible Technologies, Inc. (“IT,”) hereby offers you (“Licensee”) the right to install and use certain copyrighted computer software produced by IT under the following terms and conditions. This License shall govern the use of the software known as “Golden Tee LIVE 2010” (“Update”) when applied as an update to pre-existing Golden Tee LIVE-equipped hardware (“GT Cabinets”) equipped with an earlier version of the Golden Tee LIVE software
(“Prior Version.”)
1) Licensing Fee
The Licensing Fee (“LF”) shall be as follows:
•
US$0.00 (Zero United States Dollars and zero cents.)
2) Term
The License shall be valid on the first date that both the LF is paid for the Update and it is installed on a GT Cabinet. If the Update has been offered or sold to you under the terms of a Term Software License, the terms of this License shall become applicable if and when the Term Software License terminates in favor of this Perpetual Software License, as set forth in the Term Software License. The term shall be perpetual and throughout the
Universe for the Update on the GT Cabinet upon which it is installed at the time the LF is paid. Updates are not transferrable to any other GT Cabinet, for any reason. If a GT Cabinet with an Update is destroyed or otherwise taken out of operation, this License shall terminate.
3) License Rights
Licensee shall have the right to utilize the Update on authorized GT Cabinets in the normal course of business and as controlled by the Rules of ITNet, as set forth in a separate “Operator Agreement” document, the terms and conditions of which, where not conflicting with the terms and conditions herein, are hereby incorporated by reference. Updates may only be operated on GT Cabinets which are installed in commercial locations, as that term is defined by IT, and to which there is general access by all parties with a general right to enter the location where the GT Cabinet is operated.
4) Legal Operation
Updates include various features which may not be lawful to operate in any given jurisdiction. No provision of any feature, or its licensure to Licensee under the terms herein shall be deemed as advice that operation of that feature is lawful or not lawful in any given jurisdiction. Licensee shall make reasonable efforts to disable any user-adjustable feature which they know or should have known as not lawful to operate in the location where a GT
Cabinet with an Update is being operated.
5) Termination and Rollback
In the event that this License is terminated for whatever reason, Licensee shall have absolutely no right to operate any GT Cabinet upon which an
Update has been installed. IT reserves the absolute right, at its sole discretion, to terminate the operation of any GT Cabinet upon which an unlicensed
Update is installed. If Licensee wishes to restore such a GT Cabinet to operating condition without acquiring a new License for the Update, IT will rollback that GT Cabinet, at no charge to the Licensee, to the Prior Version upon return (at Licensee’s expense) of the required hardware to IT’s service center.
6) Governing Law and Jurisdiction
The validity and construction of this License and of the rights and obligations set forth herein shall be determined and governed by the laws of the State of Illinois. The parties hereby submit to the Jurisdiction of any state or federal court in Cook County Illinois. Licensees operating outside the borders of the United States of America, regardless of their citizenship or residency, explicitly agree to allow any assets they may have in the USA or any other foreign country to be attached, garnished, forfeited or otherwise reached by any legal act if, after due process of law, they are found to be liable to IT for damages by reason of breach of this License.
7) Warranty
If the Licensee discovers any physical defect in the media (disk, EPROM, flash media, etc.) on which the Update is distributed or in the documentation, which in the opinion of Incredible Technologies, Inc. (IT) prevents the product from being used as reasonably intended, IT will replace the media or documentation at no charge. The purchaser must return the item to be replaced, with proof of purchase, to IT within 90 days after taking delivery of the
Update.
8) Disclaimer and Waiver of Remedies
Acceptance of this License and installation of the Update includes disclaimer and waiver of any and all implied, statutory, or common-law warranties, including warranties of merchantability and fitness for a particular purpose, and limits the purchaser's remedy to returning the Update to IT for replacement.
IT makes no warranty or representation, either express or implied, with respect to Updates, their quality, performance, merchantability, or fitness for a particular purpose. Updates are licensed "as is," and the Licensee, by installing the Update, assumes the entire risk as to their quality and performance other than as explicitly set forth herein.
Acceptance of this License and installation of the Update includes disclaimer and waiver of any and all direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the Update, even if advised of the possibility of such damages. The warranty and remedies set forth above are exclusive and in lieu of all others, oral or written, express or implied. No person, seller, dealer, agent, or employee is authorized to make any modification or addition to this limited warranty.
In jurisdictions which do not allow the exclusion of implied warranties or liability for incidental or consequential damages, acceptance of this License and installation of the Update includes stipulation that the most minimal requirements of the law of those jurisdictions shall govern any additional required additional rights of Licensee.
9) Severability
If any provision of this License shall be held by a court of competent jurisdiction to be illegal, invalid or unenforceable, the parties nevertheless agree that the court should endeavor to give effect to the parties' intentions as reflected in the provision, and the remaining provisions shall remain in full force and effect.
GOLDEN TEE® Unplugged, ITS®, INCREDIBLE TECHNOLOGIES®, IT®, ITNet®, and IT incredible TECHNOLOGIES® are the properties of Incredible Technologies, Inc.
All Rights Reserved.
© Copyright 2007-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law. All other marks are the properties of their respective owners. All rights reserved.
TABLE OF CONTENTS
Silver Strike Bowler’s Club™ Version 10/09 Page 1
© Copyright 2008-2009 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Silver Strike Bowler’s Club™ Version 10/09 Page 2
© Copyright 2008-2009 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
IRS FORM W-9 ........................................................................................................................................................................................... 91
NOTE: PLEASE RETAIN ORIGINAL SHIPPING BOX FOR SERVICE AND REPAIR.
This kit is designed for use in cabinets with a JAMMA cable and wiring installed.
If you do not have a JAMMA harness already installed in the cabinet you have selected and are wiring the cabinet yourself, refer to the JAMMA Wiring Diagram in Appendix B.
Do NOT install this kit when the cabinet is powered on. Make sure the cabinet is unplugged from all power sources before and during installation.
Silver Strike Bowler’s Club™ Version 10/09 Page 3
© Copyright 2008-2009 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
UPDATE, SHOWPIECE AND KIT CONTENTS
Please check the list below for the appropriate kit or update that you own.
SSBC 07 TO SSBC 09 DVD UPDATE CONTENTS
The DVD Software Update Manual Begins on Page 5.
(1) Software Upgrade Disk
(1) New Marquee
SSB TO SSBC UPGRADE KIT CONTENTS
The DVD Upgrade Manual Begins on Page 7.
(1) I/O board
(1) Cabinet Identification Device (CID)
(1) Software Upgrade Disk
(1) Antenna & Housing
(1) USB Card Reader
(1) New Marquee
SHOWPIECE CABINET CONTENTS
The Showpiece Cabinet Manual Begins on Page 11.
Shipped inside a plastic parts bag attached to the front of the cabinet:
(1) Power Cord
(1) Game Manual
(1) Plastic Bag of Misc. Parts
(1) 15' 2-Wire RCA Audio Cable
(1) 15' VGA Video Cable
(1) RCA to 1/8" Audio Adapter Cable
NOT Included with your Showpiece Cabinet
You will need to supply a digital display for the game's main monitor, and an appropriate stand or wall mount. Be sure that the stand or wall mount is UL listed. Incredible Technologies recommends a 42" HDTV that supports
720p for the best presentation, game play and earnings potential. A list of potential sources for acquiring displays, stands and wall mounts can be found on www.itsgames.com.
COMPLETE KIT CONTENTS
The Complete Kit Installation Manual Begins on Page 20.
(1) Silver Strike Bowler’s Club Nighthawk System box
(1) I/O Board Assembly
(1) Cabinet Identification Device (CID)
(1) 6’ SVGA Cable
(1) 6’ Audio Cable
(1) USB Card Reader
(3) 6’ USB Cables
(1) A/C Power Cord
(1) I/O Board Power Cable
(1) Antenna and Housing
(1) 3” Trackball
(1) Trackball Plate
(1) SSBC Marquee
(1) SSBC Control Panel Graphics
(1) Set SSBC Side Decals
(1) Manual
(1) Quick Install Guide
(1) Parts bag containing buttons, cables and hardware
If any kit components are missing or damaged please contact Incredible Technologies Technical Support at
847-870-7027 x121. Replacement Parts can be found in Appendix C.
Silver Strike Bowler’s Club™ Version 10/09 Page 4
© Copyright 2008-2009 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
SSBC 2009 DVD UPDATE INSTRUCTIONS
UPDATES SILVER STRIKE BOWLER'S CLUB 2007 TO SSBC 2009
To start you will need:
•
•
Silver Strike Bowler's Club 2009 Update Disk labeled Game Version 2.XX.XX
External USB 2.0 DVD drive. For convenience, an extra USB cable is provided with each Silver
Strike Bowler's Club cabinet or kit. It should be located under the control panel along with a 3-prong
AC power cord to power the DVD drive. Please check your DVD drive, as some require their own power connector.
The DVD Update comes with:
• Software Update Disk marked Silver Strike Bowler's Club 2009 Version 2.XX.XX
• New Silver Strike Bowler's Club 2009 Cabinet Marquee
Follow these steps carefully:
1. Complete a collection on your machine.
2. Turn off all power to the game. It is best to use the Soft Power Button located on the underside of the control panel. Note that some cabinets may not have the Soft Power button installed.
3. Plug power cord of DVD player into outlet.
4. Connect USB cable from DVD player to Nighthawk Chassis.
5. Turn on DVD player and insert the Upgrade DVD Disk; close drawer.
6. Turn on power to game with the Soft Power Button (if available). It is important to not lose power
or turn off the game during this software update!
7. The game should automatically detect the DVD player and run the Installer program.
8. Installer will read your CID, I/O board, & Nighthawk chassis to make sure this upgrade is possible.
9. Press start to connect to ITNet for authorization. A Successful message will appear when complete.
10. Press start again to begin the installation of the software upgrade. Please be patient during this process. Important! Do not lose power or turn off the game after the start button has been
pressed or any time while the update is in progress.
11. The upgrade will take about 20-30 minutes to complete.
12. When the install is complete, Installer will ask you to turn off the game, remove the DVD from the player, then disconnect the DVD player and then turn the game back on.
13. Once complete, enter the System Setup menus and verify that the software version is Version
2.XX.XX.
Silver Strike Bowler’s Club™ Version 10/09 Page 5
© Copyright 2008-2009 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
SSBC 2009 DVD UPDATE INSTRUCTIONS
UPDATES SILVER STRIKE BOWLER'S CLUB 2007 TO SSBC 2009
MARQUEE INSTALLATION
For Newer Dedicated Cabinets
1. Remove the 6 security screws that hold the cabinet bezel in place. Refer to the SSBC Manual for detailed instructions. Disconnect the two speaker connectors. Open the hinged control panel and pull the bezel toward you, so the marquee artwork is exposed.
2. Carefully remove the old marquee. Be sure the viewing area is clean and free of dirt and debris.
3. Carefully trim ¼" off the right side of the new marquee. This should allow the new marquee to rest flat in the recessed area of the bezel. Be sure it is straight and oriented correctly. Secure the marquee in place with tape. Double-sided tape is highly recommended. Make sure the new art lays flat and is not bowed or stressed.
4. Replace the cabinet bezel, making sure to reconnect the speaker connectors.
For Older Dedicated Cabinets and Golden Tee Fore! Cabinets
1. Using the old marquee glass as a template, center the glass on top of your new marquee. Make sure that all the printed images are visible.
2. Using an X-acto® knife or other sharp blade, score the new marquee deeply by following the edges of the old glass as a guide. CAUTION: Do not cut on table or counter top. Use a cutting board
or a disposable surface.
3. Carefully break off any excess material you have cut off.
4. Be sure the light behind the marquee works.
5. Clean the glass on both sides to give players a clear view of the new marquee.
6. Install the marquee graphics and glass securely.
NOTE: Marquee installation will be different for cabinets that were not manufactured by Incredible
Technologies. Consult your manual.
Silver Strike Bowler’s Club™ Version 10/09 Page 6
© Copyright 2008-2009 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
DVD UPGRADE INSTRUCTIONS
ORIGINAL SILVER STRIKE BOWLING TO SILVER STRIKE BOWLER'S CLUB 2009
To start you will need:
A USB 2.0 DVD reader (with USB cable & power cable)
DVD Upgrade Kit contents
New I/O board
New Cabinet Identification Device (CID)
Software Upgrade Disk
Antenna & Housing
USB Card Reader
New Marquee
Please Note: Your New I/O Board should have the same connections as your old I/O Board. Generally a
Kit I/O Board has a JAMMA connection, and the I/O Board from a Dedicated cabinet has multiple singlerow keyed header connections. DO NOT INSTALL if the I/O Board connections are different than the one currently in use. Contact IT for the correct component.
Follow these steps carefully in the following order. Part 1 MUST be completed first.
PART 1
1. Complete a collection on your machine.
2. Turn off all power to the game.
3. Plug power cord of DVD player into outlet.
4. Connect USB cable from DVD player to Nighthawk Chassis.
5. Turn on DVD player and insert the Upgrade DVD Disk; close drawer.
6. Turn on power to game. It is important to not lose power or turn off the game during this
software update!
7. The game should automatically detect the DVD player and run the Installer program.
8. Installer will read your CID, I/O board, & Nighthawk chassis to make sure this upgrade is possible.
9. If all is OK, Installer will ask you to Press Start to Begin.
10. After a short time, Installer will prompt you to turn off the game and proceed with Part 2 of the
Software Update.
PART 2
1. Turn off all power to the game.
2. Copy the 3 dipswitch bank settings (SW200, SW201 and SW202) from your old I/O board to the
New I/O Board.
3. Install the New I/O Board in the game cabinet. Be sure the New I/O Board is the correct type
of board for your cabinet (JAMMA or Non-JAMMA).
Silver Strike Bowler’s Club™ Version 10/09 Page 7
© Copyright 2008-2009 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
4. Install the new CID in the game cabinet (NOTE: keep the old CID for later upgrade step).
5. Turn on power to game. It is important to not lose power or turn off the game during this
software update!
6. The game may change the version of the software in the CID and/or in the I/O board. If so, it might ask you to power cycle the game. Please only power cycle the game IF and when it tells you to do so.
IMPORTANT NOTE FOR MID-RES MONITORS
When the game is first turned on, the bootup text will be garbled and unreadable.
This is expected. When you see a screen with red “text” for 15 seconds, or if you see a flashcode 11 on D102 of the I/O Board, turn off power to the cabinet, wait 10 seconds, and power the cabinet back on.
The update process should continue automatically.
7. The game should automatically detect the DVD player and begin the Installer program again.
8. If all is OK, Installer will ask you to disconnect the new CID. Power to the cabinet must remain
ON.
9. After disconnect, Installer will ask for you to connect the old CID.
10. After the old CID is connected, Installer will verify and mark the old CID. When complete,
Installer will ask you to remove the old CID. This CID can not be used again. Be sure to mark it as disabled.
11. After disconnect, Installer will ask you to re-attach the new CID.
12. After the new CID is connected, Installer will ask you to press the Start button to begin the software upgrade.
13. Press start to begin the installation of the software upgrade. Important! Do not lose power or
turn off the game after the start button has been pressed or any time while the update is
in progress.
14. When the install is complete, Installer will ask you to turn off the game, remove the DVD from the player, then disconnect the DVD player (USB cables and power cables), and then turn the game back on.
15. The upgrade is complete. This first boot will take longer than normal, so please be patient!
16. Discard your old CID. It is no longer usable.
17. Place the new Cabinet ID Number sticker on the back of the cabinet. The old ID Number is obsolete.
18. You will need to register your new SSBC game after the update process is complete. Use your
ITNet Operator ID Card to access the registration menus, or go to the System Setup Main
Menu, then select ITNet Settings/Register Game.
If during registration you get an “ITNet Unavailable” message, reboot your machine before attempting the registration process again.
Silver Strike Bowler’s Club™ Version 10/09 Page 8
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
MARQUEE, GRAPHICS & ANTENNA INSTALLATION
For Newer Dedicated Cabinets
1. Remove the 6 security screws that hold the cabinet bezel in place. Refer to the SSBC Manual for detailed instructions. Disconnect the two speaker connectors. Open the hinged control panel and pull the bezel toward you, so the marquee artwork is exposed.
2. Carefully remove the old marquee. Be sure the viewing area is clean and free of dirt and debris.
3. Carefully trim ¼" off the right side of the new marquee. This should allow the new marquee to rest flat in the recessed area of the bezel. Be sure it is straight and oriented correctly. Secure the marquee in place with tape. Double-sided tape is highly recommended. Make sure the new art lays flat and is not bowed or stressed.
4. Replace the cabinet bezel, making sure to reconnect the speaker connectors.
For Older Dedicated Cabinets and Golden Tee Fore! Cabinets
1. Using the old marquee glass as a template, center the glass on top of your new marquee. Make sure that all the printed images are visible.
2. Using an X-acto® knife or other sharp blade, score the new marquee deeply by following the edges of the old glass as a guide. CAUTION: Do not cut on table or counter top. Use a cutting board or a disposable surface.
3. Carefully break off any excess material you have cut off.
4. Be sure the light behind the marquee works.
5. Clean the glass on both sides to give players a clear view of the new marquee.
6. Install the marquee graphics and glass securely.
NOTE: Marquee installation will be different for cabinets that were not manufactured by Incredible
Technologies. Consult your manual.
Install Side Decals
1. Locate the place where the side decals will be viewed best on your cabinet. Refer to the diagram included on the decal sheet and in the SSBC manual for optimal placement. Make sure the sides of the cabinet are as smooth and flat as possible. Remove all previous residue from prior decals to allow for a higher quality finish.
2. Remove the first of the new cabinet side decals from the backing.
3. Center the first decal on the location selected for your cabinet.
4. Using your hands (or a decal roller/squeegee), press down firmly starting from the center and smooth the side decal outward. Make sure all bubbles have been pressed out for a clean, flat surface.
5. Repeat for each of the remaining side decals.
INSTALL ANTENNA (ONLINE KIT ONLY)
Mount the supplied antenna to the upper back of the cabinet. When mounted vertically, the antenna is omnidirectional, so be sure it is as straight as possible to get the widest signal area. Drill a 9/32” or 5/16” hole behind the antenna cover. Feed the cable through the hole and route the cable to the I/O board. Attach the antenna cover to the back of the cabinet using two 6x3/4” Hex screws.
NOTE: Take care not to bundle the antenna wire with other cables in the cabinet.
Silver Strike Bowler’s Club™ Version 10/09 Page 9
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Antenna Adjustment
The antenna connects to the I/O Board and is mounted in a housing to the back of your cabinet. A strong wireless signal is very important to getting the most out of you game. Depending on the positioning of the game in the location, you may need to adjust the antenna’s position to achieve the best signal. The antenna’s housing allows for a variety of positions within, and the housing itself can be easily moved to a different location using tape or screws. See the Wireless Signal Strength and Antenna Guide found in Appendix F of the manual for more information on getting the best possible wireless signal strength for your game.
USB CARD READER INSTALLATION INSTRUCTIONS
If your cabinet already has a card reader, follow Step 1A. If your cabinet does NOT have a card reader, follow step 1B. The template to help you drill the proper sized hole can be found in
Appendix H of the Silver Strike Bowler’s Club manual.
Step 1A Remove Existing Card Reader (GT4 Cabinets)
If you are using a Golden Tee Fore! cabinet, the existing card reader must be removed and replaced with the USB Card Reader supplied in this kit. Silver Strike 2009 Bowler’s Club requires a
USB card reader to take advantage of current technology. To remove your current card reader, open the coin door to access the card reader. Reach inside and disconnect the ribbon cable from the card reader. Then from inside remove the four 11/32” nuts that hold the card reader to the inside of the cabinet. Once loose, pull the card reader out through the front of the cabinet.
OR
Step 1B Cut Hole for USB Card Reader (Other Cabinets)
If your cabinet does not have a card reader installed, you must cut a hole to mount the supplied card reader. The card reader is a very important aspect to Silver Strike 2009 Bowler’s Club, and is very important to keep in good working condition. Players are required to use a card to identify themselves for most of the online features. If the card reader is not working properly, these features will not be available.
Position the Card Reader Hole Template (found in Appendix H of the SSBC manual) onto the front of the cabinet, and as high up as possible so players won’t have to stoop over to insert their cards.
Use an awl to mark the center of the four bolt-holes and drill them to size. Use an electric handsaw to cut the rectangular opening to house the card reader.
Step 2 Install NEW USB Card Reader
Place the back end of the USB card reader through the opening on the cabinet. The large, “fat” part of the front of the card reader faces up. Insert the four carriage bolts into the mounting holes of the metal bezel. Reach through the coin door to secure the 11/32” nuts to the carriage bolts, and secure the card reader in place. Connect the USB cable to the card reader and feed the rest of the cable to the back of the cabinet. Connect the other end of the cable to the System System box.
Power the game back on and test the card reader using the Card Reader Test located in the
Troubleshooting Shortcuts Menu in System Setup.
Silver Strike Bowler’s Club™ Version 10/09 Page 10
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
SHOWPIECE CABINET
Congratulations on purchasing a Silver Strike Bowler’s Club Showpiece Cabinet. The game comes complete and ready to plug in and start earning money.
LEG LEVELER ADJUSTMENT
Once your game is in position at the location, it is necessary adjust the leg levelers. The leg levelers will help stabilize the game on an uneven floor, and help it from moving or shifting during game play. The game is shipped with the two front and two rear leg levelers installed. Adjust the levelers as necessary to level and stabilize the game.
MOUNT MAIN SCREEN DISPLAY
Position the Showpiece cabinet in front of an HDTV of your choice.
The size and model of the display you choose should depend on your location. Incredible Technologies recommends 720p flat panel HDTVs from 32" or larger.
The HDTV can be mounted to a wall or to an appropriate display stand. Be sure that the top of the Showpiece cabinet has at least 24" clearance in all directions. Insufficient clearance may result in damage to your display or player injury.
Recommended height for your display may vary depending on your location and player base. As a general rule, the minimum height of the bottom of the display viewing area should be 42" from the floor.
INSTALL MARQUEE
Your Showpiece cabinet comes with a framed marquee header that can be easily attached to the top of your monitor. The brackets for the header are shipped inside a separate cardboard insert labeled Parts – Do Not
Discard within the cabinet packaging. The insert is located on the top of the control panel.
First, Attach the two brackets to the back of the universal mounting plate you are using for your HD display. The brackets share the same screws used to affix the display to the mounting plate, and are sandwiched between the plate and the back of the monitor. Once the brackets are in place, slide the marquee frame onto the clips on the two newly mounted brackets. Be sure the tab on the clips rest inside the channel on the marquee frame.
Silver Strike Bowler’s Club™ Version 10/09 Page 11
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
DIP SWITCH SETTINGS AND NIGHTHAWK
SYSTEM BOX
DIP Switch Settings
The DIP switch settings in your Showpiece cabinet have been factory set to be connected through VGA cables.
DIP switch bank Sw201 on the I/O Board controls the video resolution for the main monitor. If a different resolution is necessary for your display, or you are using a secondary display, refer to the chart below for the proper setting.
NOTES:
A reboot is required when changing resolutions
Video and audio connections to HDTVs vary, and may require additional cables not included with the Showpiece cabinet. Also, some displays may not support the resolution needed for your game. Check your display's manual for additional information.
Silver Strike Bowler’s Club™ Version 10/09 Page 12
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
VIDEO CONNECTIONS
For any questions related to Showpiece cabinet connections, see the Showpiece Connections Guide at http://www.itsgames.com/itsgames/Products/SilverStrike/SSBC2009/specs.jsp
To connect the primary video monitor to the Nighthawk system box, connect one end of the VGA cable to the VGA output on the system box, and the other end of the cable to the proper input on the HDTV (typically labeled Computer, PC or VGA. Select the proper input from the TV menu.
DIP Switch Settings
DIP switch bank Sw201 on the I/O Board controls the video resolution for the main monitor. If a different resolution is necessary for your display, refer to the chart on the previous page for the proper setting.
Note: A reboot is required when changing resolutions.
AUDIO CONNECTIONS
AUDIO
: Connect the 2-wire RCA (red and white) audio cable from the RCA audio out on the system box to a
1/8 th
-inch Stereo Y-Adapter. Connect the adapter to the television PC audio input.
Example of PC Input with 1/8 th
-inch Audio
Input
Note: PC Inputs on most televisions accept an 800x600 signal. Some models will only display a 640x480 signal and others will accept up through a 1280x720 signal across VGA, but not all. See television specifications for details.
Silver Strike Bowler’s Club™ Version 10/09 Page 13
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
INSTALL SECONDARY MONITOR
If you plan to use Two TVs for your video outputs, follow the instructions below.
ABOUT THE SECONDARY MONITOR
Most Incredible Technologies games support a secondary monitor so more of your players can see the action.
SSBC can also show the main display on the second monitor.
Incredible Technologies recommends using a 16:9 computer monitor. With SSBC, the second monitor requires an SVGA connection from the Nighthawk system box to the digital display of your choice. See the Sw202 DIP switch settings on page 12 to adjust the display.
PRIMARY VIDEO
See previous page for connecting the primary monitor using a VGA cable.
SECONDARY VIDEO
The secondary monitor requires an S-Video connection from the
Nighthawk system box to the digital display. See the Sw202 DIP switch settings above for proper adjustments.
NOTE: S-Video only works in SVGA or VGA, not with Low or
Medium Resolutions. If there is any difficulty viewing the secondary monitor, check General Adjustments in Operator
Adjustable settings to ensure that the 2 nd
Monitor Mode is set for S-Video or VGA.
Silver Strike Bowler’s Club™ Version 10/09 Page 14
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
FINAL CHECK
APPLY POWER
Connect the power cable to the plug on the back of the cabinet. Then plug the cable into a 3-pronged, grounded wall socket. Locate the power switch on the back of the cabinet and turn it on. Note: If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
Watch the game carefully when you first turn it on. Look and smell for smoke (TURN IT OFF IMMEDIATELY IF
ANY IS NOTICED). Make sure the fan inside the chassis is running and the LED’s on the I/O board are flashing.
If not, something is wrong, turn off the game.
Check the Cabinet ID Device (CID) Number
Watch the screen during boot-up and wait for a yellow/gold verification screen to appear. Note the Cabinet ID
Number (CID) that appears on this screen, and verify that it matches the CID number printed on the back of the cabinet. The screen will automatically time out and boot-up will continue.
Check the Coin Switch and Bill Validator
Try the coin switch. Drop quarters or tokens through to check the coin mech. Insert a dollar bill into the bill validator and listen for the credits to ring up. Make sure the game is adding credits and the correct quantity. You can use the PLAYER CONTROL TEST by pressing the System Setup button inside the coin door and entering the SYSTEM TESTS MENU. Make sure all of the controls work.
Checking the Wireless Connection Signal Strength (Online Only)
There are two ways to check the signal strength of your wireless connection. First, you can power the game off and on. A signal meter will appear in the lower right corner of the game’s boot-up screen. The number of bars that are displayed indicate the signal strength.
Additionally, you can enter Operator Mode by pressing the System Setup button inside the coin vault door. Once at the main Operator Mode menu, use the trackball and Start button to select ITNet Settings, then Communication Settings to view more information.
Cabinet Temperature
The state of the art Nighthawk hardware is extremely powerful, and therefore generates a substantial amount of heat. Measures have been taken to keep the various components cool during normal use. If overheating occurs, game play and hardware longevity may be affected. Use the Check Cooling menu in the System Setup menus to monitor the temperature within your cabinet. Enter System Setup by pressing the System Setup button inside the outer door of the coin vault. Once at the main System Setup menu, use the trackball and Start button to select Troubleshooting Shortcuts, then Check Cooling.
Custom Adjustments
Upon initial power-up, the game will initialize to factory default settings. These settings affect game elements such as number of credits per coin, volume settings, etc. The System Setup section in your game manual will describe how to alter these settings and view the system audits or run system tests.
Silver Strike Bowler’s Club™ Version 10/09 Page 15
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
GENERAL CABINET MAINTENANCE
Games that are in good working condition, with clear monitors, clean control panels and working trackballs will make more money than a machine in poor condition. It is definitely worth your time and attention to protect your investment with a little common care. Each week, clean the display and wipe down the control panel to bring back that new game look. Test the trackball and buttons regularly to make sure they are playing properly. And perhaps most important, make sure the coin mechs and bill acceptors are in good working order.
CARE AND CLEANING OF RUBBER BUMPER
The rubber bumper on the front of the cabinet’s control panel is made from durable nitrile rubber. Clean it using a mild soap and water solution or blue window cleaner.
NIGHTHAWK AIR FILTER
The Nighthawk Chassis comes equipped with an external electrostatic air filter. This filter is held in place by a metal bracket, attached to the chassis. The filter prevents debris from entering the chassis and damaging the electronic components. A clogged filter will impede airflow, thus building up unwanted heat which can cause damage to your hardware. Be sure to check this filter at least once a month. Remove the filter by sliding it out of its housing. Shake off excess dirt and if necessary clean it with soap and water. Be sure the filter is completely dry before reinstalling the filter.
TRACKBALL MAINTENANCE
The trackball will require periodic maintenance to assure optimum performance. In most cases the inside of the trackball simply needs to be cleaned of any accumulated dust and debris.
To access the inside of the trackball, remove the 6 Phillips head screws that hold the trackball together and remove the top cover. Clean out any dust and debris inside the trackball. Polish the rollers and remove any foreign material that may be on the rollers. Do not lubricate the bearings, as this will only attract more dust. If the bearings do not spin freely it is best to replace the bearing assembly. Inspect the rollers for any nicks that may cause poor performance and replace if needed. Inspect the ball for any nicks and replace if needed.
Parts can be obtained from Happ Controls and is an economical option rather than replacing the entire trackball assembly.
It is critical that the green field ground wire be properly connected to field ground. This prevents the trackball from building a static charge that can cause the game to lock up or reset. A static discharge can also damage the trackball’s electronic components, as well as the main system.
CARE AND CLEANING OF COOLING FANS AND VENTS
The hardware that runs Silver Strike Bowling is quite sophisticated, and many of the chips and processors will get hot very quickly. Like your desktop PC, the Nighthawk hardware needs adequate ventilation to work properly.
Dust and dirt can be a major cause to overheating and will lead to costly repairs. At least once a month, check to make sure the cabinet and chassis fans are working and free of dust and debris. Use a vacuum to clear all the ventilation holes on the cabinet at this time as well.
Silver Strike Bowler’s Club™ Version 10/09 Page 16
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
SHOWPIECE CABINET REPAIR PROCEDURES
SYSTEM CHASSIS BOX
The Nighthawk Chassis houses most of the game electronics and hardware in one box that can be easily installed. As with all electronic equipment, the Chassis box should be handled with extreme care. Shock, severe temperature, or sudden impacts can damage the internal components that require costly repair.
Note!
Turn off power to the cabinet and remove the power cord from the back of the cabinet when performing any of the following.
System Chassis Removal
1. Unlock the control panel and open to expose the Nighthawk system box.
2. Disconnect all connections to the system box. Be sure all wires and connectors are clear and out of the way. Label the connectors for easy reconnection.
3. Loosen the 6 ¼" hex-head screws that secure the system box.
4. Carefully lift the system box off the screws and up out of the cabinet.
System Chassis Installation
1.
2.
3.
Unlock the control panel and open to expose the inside of the cabinet.
Align the system box onto the 6 mounting screws of the internal slanted panel. The connection ports face up. Once the system box is in place, tighten the 6 ¼" hex-head screws to secure the box to the panel.
Connect the required connections. See the Connections
Diagram in the accompanying game manual for more details.
I/O BOARD
NOTE!
The I/O board is game title specific and is not interchangeable with other game titles produced by Incredible Technologies on this system. Dedicated and Retrofit Kit I/O boards are different and are not interchangeable.
I/O Board Removal
First, unlock the control panel and open to expose the underside of the control panel. Disconnect all connections from the I/O board. Refer to the I/O board connections diagram in the accompanying game manual. Label the connectors for easy reconnection and move them safely out of the way. Next, remove the 6 ¼” wood screws that secure the board to the underside of the control panel. Carefully remove the
I/O board from the cabinet.
I/O Board Installation
Place the I/O board in the proper location on the underside of the control panel. Be sure it is oriented properly so the cables reach the board. Secure the I/O board to the underside of the control panel with the 6 ¼” wood screws. Use the factory mounting holes if at all possible. Be sure the board does not “bow” or is not stressed in any way. Once mounted, connect the appropriate connectors. Refer to the Dedicated I/O board connection diagram in the accompanying game manual.
Silver Strike Bowler’s Club™ Version 10/09 Page 17
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Cabinet Identification Device (CID)
This device contains a specific ID number that identifies your cabinet. The
CID is a permanent number and must be connected to the main system box via the USB cable and working properly in order for the game to operate.
CID Removal and Replacement
If for some reason you must replace the CID, disconnect the USB cable from the CID. This is the only connection to the CID. Next, remove the two
¼” wood screws that secure the CID to the underside of the control panel.
To install a CID, reverse the order above.
Note! The Cabinet Identification Device should NEVER be removed from the cabinet, even when replacing any of the other components. The CID is the cabinet’s PERMANENT Identifier, regardless of any other components.
CASH VAULT
The Cash Vault has been designed for optimal security. With the double-locking doors, service technicians can read meters and enter System Setup mode with no access to the cash box.
Cash Vault Removal and Replacement
1) Unlock and open the outer door of the Cash Vault.
2) Using a T-15 Torx wrench, unscrew the card reader/button plate located on the right side by removing the four #8-32 screws located at the top and bottom of the plate.
3) Unplug the cable from the card reader, and disconnect the connectors for the coin meter and buttons.
4) Remove the plate and set it aside.
5) Remove the coin bin and the bill validator magazine to make it easier to work inside the vault.
6) Unplug the bill validator cables, and push the cables for the bill validator, card reader, buttons, and coin meter through the 2 holes located in the back of the vault.
7) The Cash Vault is attached by upper and lower locking brackets. These are each attached with two sockethead screws located within the vault.
8) Locate the socket-head screws on the top and bottom locking brackets. Remove the two bottom screws using a 9/64” hex key and remove the bottom locking bracket. Make sure to note how it was installed.
9) Remove the two top screws and remove the top locking bracket, again noting how it was installed.
10) You can now pull the entire vault assembly out from the front of the cabinet. The vault is attached with foam tape, so it will need to be pried out or pushed from behind to loosen the adhesive.
11) Reverse the procedure to install the new door.
Locks
The outer lock is a secure T-handle lock, commonly used in vending. To open, insert the key and turn it clockwise until the lock-handle pops out. Next, rotate the lock-handle clockwise 90 degrees to open the outer door.
The inner door has a lock installed above the System Setup button. This lock is unlocked by turning the key 90 degrees clockwise.
Volume and Service Buttons
Mounted inside the outer door are controls for Volume and System Setup. Press the Volume Up button to increase the loudness of the sounds on the game, and press the Volume Down button to make your game quieter. Press the System Setup button to access the game’s software menu system. The System Setup menus cover a variety of important areas including collections, tests, game adjustments, and optional settings.
Silver Strike Bowler’s Club™ Version 10/09 Page 18
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Bill Acceptor
The dedicated cabinet ships with a MARS AE2681 D5 bill acceptor and is mounted on the cash vault door. The default dipswitch settings for this acceptor are ON = 1,2,4-7 and OFF = 3,8.
Bill Acceptor Removal
Disconnect the cable to the bill acceptor. Remove the four 11/32” sized nuts from the mounting studs.
Disconnect the ground wire from the one lower stud. Then gently pull the accepter off the studs from the back side of the coin door.
Bill Acceptor Installation
From the back side of the coin door, place the bill acceptor onto the four mounting studs. The faceplate will protrude out the front of the coin door. Place the field ground wire on a lower stud, and install the four 11/32” sized nuts on the mounting studs and tighten. Next, connect the bill acceptor cable in the cabinet to the mating cable on the bill acceptor itself.
Stacker Removal
A blue slide switch is located at the bottom of the stacker. Engaging it allows the stacker to be removed.
Coin Mech
Coin Mech Removal
Loosen the two finger screws to release the securing braces. Slide the upper brace upward, and the lower brace downward. The mechanism should pull straight out.
Meter
This 5-volt device is mounted behind the card reader plate next to the inner door of the coin vault. One lead of the meter is connected to a +5 volt source and the other lead is connected to the appropriate signal wire. An additional opening is available just below the meter, if a second meter is desired.
CONTROL PANEL
Opening the control panel provides access to all game controls and hardware components. To open the control panel, simply use the supplied key in the lock on the back of the cabinet and lift from the back. The control panel is hinged in front and will stay open when fully extended.
Soft Power Switch
A “soft power” switch has been added to the underside of the control panel, to assist in the update process. This switch will turn off power to the cabinet so you don’t have to reach around to the main power switch located on the back of the cabinet.
Note!
If you turn power off using the Soft Power Switch, you must use this same switch when turning power back on.
Trackball Replacement
To replace a trackball, open the control panel and remove the 4 long screws holding the trackball in place. Be careful not to lose any of the screws, washers and lock washers. Disconnect the wire harness and ground wire and remove the old trackball. Position the new trackball in the proper orientation over the existing standoffs.
Make sure that the arrow on the trackball that points to the monitor is pointing up. Replace the 4 long screws and washers. Do not over tighten! Screw in until the lock washer is fully compressed. Reconnect the wiring connector and ground wire.
Note! The field ground wire is critical to avoid electrical problems and assure optimal performance.
Silver Strike Bowler’s Club™ Version 10/09 Page 19
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Button Replacement
All of the buttons on the control panel require a 1 1/8 th
inch hole, and are pre-drilled on the dedicated control panel. To remove a button, disconnect the wires from the button assembly by sliding the wires off of the micro switch posts. Next carefully twist the micro-switch assembly off of the button posts. Finally, unscrew the nut to remove the button from the control panel.
Place the new button assembly into the hole and position the smaller side of the micro-switch housing to face the rubber bumper, angled towards the middle. Tighten the supplied nut using a pushbutton wrench. Do not over tighten. Install the micro-switch by snapping it onto the pushbutton assembly by hand. Position the assembly so the micro switch posts face the rubber bumper, angling towards the middle. Reconnect the wires by sliding the wire assembly onto the contact posts of the appropriate micro switch. See the wiring diagrams in the back of this manual.
Control Panel Removal
To remove the control panel from its hinge, Disconnect the trackball cable, field-ground wire, and the control panel interconnect connector to the I/O board. Remove the screw that attaches the safety cable to the control panel. Remove the four ¼” screws holding the panel to the hinge.
Control Panel Graphics Removal
The control panel artwork has been screened onto a solid sheet of polycarbonate, which is resistant to scratches and burns. Unfortunately long exposure to excessive situations may damage the surface over time. To remove and replace this piece, the pushbutton and trackball assemblies must first be removed. Separate the polycarbonate piece from the wood portion of the panel by starting at one corner and slowly peeling the two apart.
The overlay has adhesive on the entire surface and will take some force to separate the pieces due to the adhesive. Once removed, the graphic overlay will not be able to be used again.
Control Panel Graphics Installation
To install a new polycarbonate Graphics overlay, make sure the wood control panel surface is clean, smooth, and free from glue, dirt and debris. Remove the paper protecting the adhesive from the new artwork/cover panel.
Carefully place it on the wood panel, aligning it properly. Press and smooth firmly to assure that it is secure.
Replace the buttons and trackball in the correct orientation.
SPEAKERS
The speakers are mounted in the bottom front of the cabinet, just below the coin vault. Sounds and speech are important aspects to the play experience and should be adjusted and maintained for optimal results. Make sure your speakers are in good working condition, are wired correctly, and are grounded properly to avoid buzz or hiss.
Speaker Access
In order to reach the speakers, unlock and raise the hinged the control panel. The speakers are located just below the coin vault. Remove the 4 nuts with an 11/32” nut driver to remove the speakers from their mounting.
Note: Both speakers must be identically wired to work properly. For optimal sounds, both speakers must be in phase with one another. Be sure the positive wire is connected to the positive terminal of each speaker and the negative speaker wire is connected to the negative terminal of each speaker.
Silver Strike Bowler’s Club™ Version 10/09 Page 20
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
ANTENNA (ONLINE ONLY)
The antenna connects to the I/O Board and is mounted in a housing on the back of the cabinet. A strong wireless signal is very important to getting the most out of your game. Depending on the positioning of the game in the location, you may need to adjust the antenna’s position to achieve the best signal. The antenna’s housing allows for a variety of positions within, and the housing itself can be easily moved to a different location using tape or screws. See the Wireless Signal
Strength and Antenna Guide found in the accompanying game manual for more information on getting the best possible wireless signal strength for your game.
CARD READER (ONLINE ONLY)
The Card Reader is a very important aspect to Silver Strike Bowling, and is very important to keep in good working condition. Players are required to use a card to identify themselves for most of the online features. If the card reader is not working properly, these features will not be available.
Card Reader Removal
Access the card reader through the coin door opening. To remove the card reader, disconnect the USB connector from the Card Reader.
Then remove the 4 T-15 security screws that secure the mounting panel that holds the card reader, coin counter and buttons. Next, remove the two Phillips head screws holding the card reader to the mounting panel. Once loose, pull the card reader out through the front of the panel.
Card Reader Installation
Open the coin door to access the card reader mounting. Place the back end of the card reader through the opening on the mounting panel. The larger portion of the card reader bezel should be in the up position. From the backside of the panel, secure the card reader to the panel with the 2 Phillips head screws. Once in place, reconnect the
USB cable to the card reader. Attach the mounting panel to the coin door with the 4 T-15 security screws. Power the game back on and test the card reader using the Card Reader Test located in the Troubleshooting/Info Menu in System Setup.
Silver Strike Bowler’s Club™ Version 10/09 Page 21
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
COMPLETE KIT INSTALLATION
RECOMMENDED TOOLS
Have the following tools ready before you begin to install this kit:
¼", 11/32" and 7/16" Sockets or Nut Drivers
Phillips Head #2 Screw Driver
3/16”, 7/32” and 9/32”, or 5/16”, 3/8”, and ¾” Drill Bits
1 1/8" and 3 1/2“ Hole Saw or Drill Bit
Small Flat Blade Screwdriver
Jig/Sabre Saw
Router
Push Button Nut Socket or Large Adjustable Pliers
X-acto® Knife or other Sharp Knife/Razor Blade
Wire Cutters
Scissors
Tape Measure
Putty Knife
Decal Roller/Squeegee
Liquid Window Cleaner & Cleaning Cloth
Vacuum Cleaner
Any tools needed to remove parts from your existing cabinet not listed above.
Many operators notice their earnings increase with touches as simple as a fresh coat of paint and a clean cabinet.
If you will be painting, you'll need these supplies:
Air Brush or Paint Sprayer,
Paint Brush, Paint Roller, and Pan
Paint (and Primer) –A black cabinet is a recommended color choice.
Sandpaper
INSTALLATION PREPARATION
BEFORE YOU START…
Before you install the Silver Strike Bowler’s Club kit into your cabinet there are a few things you should check first:
1.
Check to make sure your existing cabinet's monitor, speakers, AC power cord, lights, bill acceptor and coin mechs work. Replace or repair where necessary.
2.
Check to make sure all the necessary parts are included in your kit. If any are missing/damaged please contact IT's Technical Support at 847-870-7027 x121.
3.
Check to make sure cabinet is wired with standard earth grounded A.C. plug compatible with local building codes and/or safety requirements. If not, have a qualified electrician install one (not provided).
4.
Have all the necessary tools available to install this kit. Refer to the recommended tools list above to make sure you are prepared before you start.
5.
Make sure any parts of the system (lights, monitor, etc.) are not plugged in. Working with any part of the system plugged in or powered on can be dangerous.
6.
Keep in mind that it's been proven that the higher quality of work put into a kit installation results in a higher earning game. Make sure you have plenty of space, time, and focus to put into this kit installation.
Silver Strike Bowler’s Club™ Version 10/09 Page 22
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
PREPARING THE CABINET
CABINET SELECTION
You can choose either a new cabinet or a used cabinet for your Silver Strike Bowler’s Club game. Reusing a cabinet is by far the most cost-effective way to maximize the return on your initial investment. In either case, all you need to provide is the cabinet with a monitor, JAMMA harness, coin and bill acceptors, working fluorescent/marquee lights, and speakers.
When selecting a cabinet, keep in mind that a larger control panel allows you to mount the trackball farther from the monitor. This prevents players' hands from hitting the monitor glass when rolling the trackball forward, and will earn better than a smaller control panel closer to the monitor. An older-model Silver Strike dedicated cabinet is ideal for this purpose.
If using a Silver Strike cabinet for this installation, consider ordering a new Control Panel from Incredible
Technologies. These control panels come pre-installed with controls and graphics, and can save you considerable time and money through easy installation.
PREPARING THE CABINET FOR INSTALLATION
Follow these steps to prepare your cabinet before installation:
1. Remove the following from the cabinet: Main Logic Board(s) (and hard drive if present), Control Panel,
Monitor Viewing Glass, Marquee, and Power Supply. Now is a great time to clean both sides of the monitor viewing glass and monitor screen to ensure a clear view of the game.
2. Thoroughly clean out your cabinet. Remove all of the old buttons, joysticks, etc. DO NOT remove monitor and speaker wires or the wires that were previously hooked up to the control panel.
3. Remove the old graphics and adhesive from the cabinet including the control panel.
4. For a fresh look and best earnings, painting is highly recommended. Spray painting gives a better finish, but if an air brush or paint sprayer is unavailable a roller is second best. Remember to cover all exposed surfaces not to be painted. When not installing into an old Silver Strike® dedicated cabinet, the recommended color choice is black.
5. Make sure to have the sides of the cabinet and the control panel as smooth and flat as possible to allow for a higher quality finish when applying the control panel background, labels, and side decals.
6. The "new game look" should always apply to the inside of your game as well. A few wire ties and shrink tubing on your harness, some fastening hardware on your subassemblies, and a sweep with the vacuum cleaner will help ensure that glitches do not occur.
Check JAMMA Harness and Wiring
The Silver Strike Bowler’s Club Kit comes with a special I/O Board that uses your cabinet’s existing JAMMA wiring harness. Make sure your existing wires and connectors are in good working order. Check the JAMMA wiring diagram in Appendix B.
Check Coin Mechs and Bill Acceptor
Make sure your coin mechs and bill acceptor are functioning properly, and your coin box and stacker are in good condition. You want to make sure your game will accept money when players are ready to play.
Check Coin Door Connections
Your Golden Tee Fore cabinet should already be wired correctly through the JAMMA connector. Now is a good time to make sure your game can accept money. Check the JAMMA pinout chart in Appendix B for the correct wire colors and pins. Trace the wiring to their sources and make sure they are connected properly and securely.
Be sure the wires are away from the coin door where they can be pinched or crimped.
Silver Strike Bowler’s Club™ Version 10/09 Page 23
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Check Monitor
Silver Strike Bowler’s Club has been designed to operate with SVGA (800 x 600), VGA (640 x 480), medium resolution (512 x 384) and low resolution (384 x 256) monitor systems. The factory monitors in all Golden Tee
Fore! cabinets are compatible with Silver Strike Bowler’s Club. However, to take advantage of the best and most current quality available, it is recommended to upgrade to an SVGA compatible monitor.
Operating Silver Strike Bowler’s Club at the highest possible resolution will give your game the best results (and revenue). Many standard cabinets contain a medium-res. or VGA monitor already. If you have a low-res monitor, it may be possible to switch it to a higher resolution. Check your monitor's manual for capabilities. If not, you should consider upgrading to a newer monitor.
Also check your monitor for a DB15 VGA connector. If your current monitor has a DB15 VGA connector, it is capable of VGA or SVGA resolutions. Check your monitor’s manual on how to switch the monitor to VGA mode.
Make sure the video dip switches on the I/O board match the resolution that the monitor is expecting. Plug the video cable from the Nighthawk System box directly into the monitor. Be sure to disconnect the old composite sync video cable from the monitor.
When operating with an SVGA or VGA monitor, Silver Strike Bowler’s Club uses the standard VGA sync timing and signals. When operating with medium resolution or low resolution monitors, which are common in Golden
Tee Fore! dedicated cabinets, Silver Strike Bowler’s Club operates with composite negative serrated sync.
NOTE: In all cases a horizontal mount raster scan monitor is required.
CAUTION! Monitors are extremely dangerous and can result in severe injury. Make sure you follow and observe all safety precautions as outlined in your monitor's manual. ALWAYS disconnect the power to the cabinet before working on or around the monitor.
Remove Cabinet Graphics
Remove any decals from the cabinet. Make sure that the sides of the cabinet are as smooth and flat as possible to allow for a higher quality finish when applying the new side decals.
For a fresh look and best earnings painting is highly recommended. Spray painting gives a better finish, but if an air brush or paint sprayer is unavailable a roller is second best. Remember to cover all exposed surfaces not to be painted.
Remove Existing Card Reader (If applicable)
If you are using a Golden Tee Fore! cabinet, the existing card reader must be removed. Silver Strike Bowler’s
Club requires a new card reader, to take advantage of new credit card technology. To remove your current card reader, open the coin door to access the card reader. Reach inside and disconnect the ribbon cable from the
Card Reader. Then from inside remove the four 11/32” nuts that hold the card reader to the inside of the cabinet.
Once loose, pull the card reader out through the front of the cabinet. If you are installing an Offline kit, install the supplied card reader plate to cover this opening.
Silver Strike Bowler’s Club™ Version 10/09 Page 24
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Cut Hole for Card Reader (Online Kit Only)
If your cabinet does not have a card reader installed, you must cut a hole to mount the supplied card reader. The card reader is a very important aspect to Silver Strike Bowler’s Club, and is very important to keep in good working condition. Players are required to use a card to identify themselves for most of the online features. If the card reader is not working properly, these features will not be available.
Position the Card Reader Hole template found in Appendix H on the front of the cabinet, and as high up as possible so players wont have to stoop over to insert their cards. Use an awl to mark the center of the four boltholes and drill them to size. Use an electric handsaw to cut the rectangular opening to house the card reader.
Vacuum Cabinet Thoroughly
The "new game look" should always apply to the inside of your game as well. A few wire ties and shrink tubing on your harness, some fastening hardware on your subassemblies, and a thorough sweep with the vacuum cleaner will help ensure that glitches do not occur.
Dust and dirt can damage your hardware and cause problems with game play. Be sure that your cabinet is clean inside and out. It is highly recommended to vacuum your cabinet at least once a month, especially near the fans and vents, to avoid overheating and costly repairs.
Silver Strike Bowler’s Club™ Version 10/09 Page 25
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
ELECTRONICS INSTALLATION
INSTALL NIGHTHAWK SYSTEM BOX
The Nighthawk System box houses most of the game electronics and hardware into one box that can be easily installed. Verify that the Nighthawk System
box Power Switch is in the "ON" position.
1. Locate the area on the floor where the system box will be placed. Make sure there is enough clearance to plug in cables.
The Nighthawk System box measures 19" W x 7" H x 11" D.
2. Relocate and secure any wires to make room for the system box.
3. Place the system box so it sits flat on the floor and does not pinch wires.
Be sure there will be sufficient air flow to the system box. Overheating can damage your system.
4. Mount the system box with 6 - #6 x ¾" Hex Washer Head Sheet Metal
Screws.
INSTALL CABINET IDENTIFICATION DEVICE (CID)
The Cabinet Identification Device or C.I.D. is an innovative and important component. This device permanently identifies your cabinet as Silver Strike
Bowler’s Club. It should remain even if another component such as the I/O board or system box is replaced. The C.I.D. has a unique number to individualize the cabinet and is referred to as the
Cabinet Identification Number.
1.
Attach the C.I.D. to the inside side of the cabinet using the 2 - #6 X 1” Hex Washer Head Sheet
Metal Screws. Mount so the port is facing up and the electronics face the wall.
2.
Attach the USB cable from the Nighthawk System box.
Place the included Cabinet Identification
Number on the back of the cabinet for future reference. Refer to this number to
track your equipment and whenever you are calling in for service.
The Cabinet Identification Number is displayed in the operator menus in the lower right hand corner, and is labeled as Game ID. It is also displayed on the last line of the initial boot-up screen.
Silver Strike Bowler’s Club™ Version 10/09 Page 26
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
INSTALL I/O BOARD
NOTE: Before installing any electronics make sure cabinet power switch is in the OFF position and the cabinet power is unplugged from the wall.
Silver Strike Bowler’s Club comes with a specially designed I/O board that works with your cabinet's already installed JAMMA harness. The I/O board is used as a connection interface between the JAMMA and the Nighthawk System box.
Mount the I/O board inside the cabinet using 4 of the 6 x ¾" Hex
Washer Head Sheet Metal Screws, 1 in each corner. The existing
JAMMA harness edge connector will attach to this board. Do not attach cables at this time.
NOTE: Route all cables AWAY from the I/O Board. Laying cables on top of or below the I/O Board will result in unwanted noise or static during the game.
INSTALL ANTENNA (ONLINE KIT ONLY)
Mount the supplied antenna to the upper back of the cabinet. When mounted vertically, the antenna is omnidirectional, so be sure it is as straight as possible to get the widest signal area. Drill a 9/32” or 5/16” hole behind the antenna cover. Feed the cable through the hole and route the cable to the I/O board. Attach the antenna cover to the back of the cabinet using two 6x3/4” Hex screws.
NOTE: Take care not to bundle the antenna wire with other cables in the cabinet.
Careful placement of the antenna is important for good wireless communication. Sometimes relocating a wire or moving the antenna within the housing will deliver a more reliable signal. Once the installation is complete, be sure to use the Signal Strength test in the game’s System Setup menus. Refer to Appendix F for more details on how to achieve the best signal strength.
INSTALL CARD READER (ONLINE KIT ONLY)
Place the back end of the card reader through the opening on the cabinet. The large part of the front of the card reader faces up. Insert the four carriage bolts into the mounting holes of the metal bezel. Reach through the coin door to secure the 11/32” nuts to the carriage bolts, and secure the card reader in place. Connect the USB cable to the card reader and feed the rest of the cable to the back of the cabinet. The other end of the cable will connect to the System System box. Power the game back on and test the card reader using the Card Reader
Test located in the Troubleshooting/Info Menu in System Setup.
INSTALL TICKET DISPENSER (OPTIONAL)
Silver Strike Bowling supports Entropy 2000 Ticket Dispenser Continuous Type
(TD963CR) and Deltronic Labs DL-1275 Continuous Type ticket dispensers. If
Ticket Dispenser Pinouts you wish to connect a ticket dispenser to this game, you will have to make a cable with the proper connectors. These ticket dispensers mates with a Molex connector #03-09-1041 or #03-09-1042. The I/O board ticket connector J201 mates with a Molex connector #22-01-2047 or #22-01-3047. Simply connect
Pin
1
2 pins 1 through 4 on one end directly to pins 1 through 4 on the other end.
Consult with your ticket dispenser's manual to verify installation procedures.
3
4
You will need to set your ticket dispenser to ON from the Ticket Dispenser menu in the Operator Menus. Details can be found in System Setup section of this manual.
Function
+12 Volts
Ticket Sense
Motor Enable
Ground
Silver Strike Bowler’s Club™ Version 10/09 Page 27
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
CONTROL PANEL INSTALLATION
INSTALL OPTIONAL CONTROL PANEL FOR EXISTING I.T. CABINETS
If you are installing your kit into an existing Golden Tee Fore! cabinet manufactured by IT, you can purchase a new, fully outfitted control panel. This will not only make your installation easier, it will make your game look and play better too. Use this section to install this control panel. For all other cabinet types, refer to the next section.
Attach the new control panel to the existing hinge on the control panel drawer. Drive the 4 Phillips screws into the holes in the bottom of the control panel. The control panel comes equipped with trackball and buttons in place. Snap the switches onto the buttons. Refer to the
JAMMA wiring diagram to match up the correct wire to the correct button. The following buttons need to be connected: Start, Change
Ball, Overhead, Rotate Left, Rotate Right. Connect to the normally open post. Be sure common ground is connected to each common post.
Connect the 10-pin connector to the Control Panel connector J203 on the I/O board. Finally, connect the Trackball to the trackball connector J208 on the I/O board.
TRACKBALL AND BUTTON PREPARATION (FOR MOST KITS)
Mounting the trackball and buttons correctly and securely is very important for the profitability and safety of your new game. This kit is designed for use in cabinets with ¾" thick wood control panels where proper routing of the control panel is used to create a safe playing experience. If you do not have a ¾" thick wood control panel, please replace your control panel or choose a cabinet with a ¾" thick wood control panel installed. Keep in mind that if your current control panel has many old holes in it from previous buttons, joysticks, etc. that it may be easier to start with a new solid control panel. This will give your game a better look and feel and help it to earn better.
NOTE: If the cabinet already has a trackball plate installed, discard and replace with the new trackball plate. The metal trackball mounting plate and trackball mounting procedure have been designed to remove all bolts from the playing surface. Routing the wood control panel is required so the metal mounting plate is flush with the panel surface. An uneven playing surface or exposed edges will affect game play and could impact your earnings.
TIP: Trackball and button templates can be found in Appendix H of this manual. They include:
Trackball Template to install the trackball plate and make the appropriate routing.
Trackball Orientation Diagram to orient your trackball correctly when installing.
Button Set Templates to position and install control panel buttons.
Trackball Preparation
Install the metal trackball plate by following these steps:
1. Cut out the template from Appendix H with a pair of scissors along the noted line. Tape this template to the top of the control panel as far away from the monitor as possible, making sure that the trackball will clear the cabinet beneath it. NOTE: Installing the trackball as far away from the monitor as possible will prevent players' hands from hitting the monitor glass when rolling the trackball forward.
2. Using a sharp object, mark the eight points shown on the template on the control panel. Using a pencil, trace the outside of the template. Remove the template.
3. Drill Holes 1-4 with a 9/32" or 5/16" drill bit.
4. Drill Holes 5-8 with a ¾" drill bit.
5. Route the crosshatched region to a depth of about .075" (about the thickness of a nickel).
6. Using a sabre saw cut out the center portion by cutting between holes 5-8.
Silver Strike Bowler’s Club™ Version 10/09 Page 28
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
7. Once you have cleaned up the routed area, install the trackball plate into the control panel using the ¼"
Flat Washers and ¼-20 Nylon Hex Nuts. Be sure the mounting plate is flush with the top of the control panel.
NOTE: At this time you are only installing the trackball plate, do not install the trackball yet.
Button Preparation
The following are the steps you should take to prepare your control panel for the installation of the button assemblies:
1. Cut out the template(s) (see Appendix H).
2. Using a tape measure, measure the specified distances from the center of the trackball hole in the trackball plate and make a mark for both the left and right button reference points.
3. Lay each template over the appropriate reference marking point. Mark the centers of the remaining holes using a sharp object.
4. Drill a 1 1/8" hole at each marked point.
NOTE: Do NOT install the trackball or buttons until the control panel graphics have been applied.
Once the installation is complete, be sure to use the System Controls test in the game’s System Setup menus to ensure proper functionality of all the player controls.
CONTROL PANEL OVERLAY INSTALLATION
Silver Strike Bowler’s Club comes with an oversized control panel overlay that will accommodate a variety of existing game cabinets, but works best on Golden Tee Fore!, NFL® Blitz™ and EA Sports™ PGA Tour® Golf cabinets. Follow these instructions to correctly install the control panel overlay on one of these cabinets:
1. Make sure that the newly drilled control panel has a smooth, clean surface. Sand where necessary to make sure the graphics are installed on an even surface.
2. Clean the control panel to make sure it is free from dust, grease, metal filings, etc. Make sure that all residues (adhesive, overlay material, etc.) from the previous control panel graphics are removed. This will ensure a clean, easy, and beautiful application of the control panel graphics.
3. It is very important that the trackball and control panel graphics be mounted perfectly straight. Find the center of your trackball template and lightly draw vertical and horizontal guidelines on the control panel, marking out your centering lines.
4. Remove a small section of the protective backing from the overlay. Carefully center the overlay over the control panel by lining up the die-cut hole with the trackball template. Be sure the graphic is positioned
perfectly straight. Line up your pencil guidelines with the lines incorporated into the art. Once in position, gently press down on the section with exposed adhesive, affixing the overlay into place. Once affixed, the overlay cannot be removed.
5. While holding down the overlay over the attached area, very carefully turn over one side and remove the exposed backing. Gently lay down the exposed overlay from the center outward, smoothing with your hands or a roller as you go. Be sure the overlay remains straight and square. Repeat the process with the other side of the overlay, so the entire surface is affixed to the control panel. Make sure all bubbles have been pressed out for a clean, flat surface.
TIP: Liquid window cleaner can be sprayed onto the control panel before placing the overlay onto the control panel. The window cleaner will allow the overlay to be positioned with less risk of damage to the overlay or adhesive. Once in position, use a decal roller or squeegee to force any excess cleaner out. Be sure to add additional time for the liquid to evaporate.
6. Using an X-acto
®
knife (or other sharp instrument) carefully cut around the edges of your control panel, trimming any excess material.
7. Find the center of each hole you've drilled out for the buttons and use the knife to poke a hole into the overlay. Make a vertical and horizontal line (like a plus sign) from the center of the hole to the edges. You should be able to place your button in later with no edges showing.
Silver Strike Bowler’s Club™ Version 10/09 Page 29
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
CAUTION: If you choose to install a Plexiglas® cover over your control panel (not recommended), to ensure the safety of your players and the quality of your game make sure that all surfaces, edges and bolts that a player may come in contact with are smooth, safe and secure.
FINISHING THE CONTROL PANEL
1. Reattach the control panel to your cabinet adjusting any hinges or chains where necessary. Make sure not to pinch or crimp any wires while re-attaching the control panel.
2. Install the trackball into the trackball plate. The trackball must be oriented correctly in order to function properly. Refer to the diagram located in Appendix H for correct orientation. You will need the following parts in order to install the trackball correctly to the plate: 4 -10/32 x 2½" Phillips Head Machine Screws, 4 - #10
Flat Washers and 4 - #10 Split Lock Washers NOTE: Do not over-tighten the trackball. It will warp and cause the trackball to not operate correctly.
IMPORTANT! Be sure to install your trackball securely, and maintain it regularly. Loose, worn, or incorrectly mounted trackballs can result in decreased earnings and possible injury to players.
3. Secure the trackball ground wire to the trackball plate at the 8-32 stud on one end with an 8-32 KEPS nut and the other end to the cabinet ground stud (usually located near the AC power cord inlet) using an 8-32 KEPS nut.
4. Install the buttons in the holes located on your control panel. Make sure you use the red button assembly for the Start button.
5. Attach the micro switches to your newly installed buttons and connect the wires up to the correct pins on the
JAMMA harness.
NOTE: The post on the switch labeled COM should connect to the ground wire and the post labeled NO should connect to the signal wire. See the JAMMA pin out chart in Appendix B.
IMPORTANT! Trackball and trackball plate MUST BE GROUNDED to Earth Ground to prevent damage to the trackball or game electronics.
Silver Strike Bowler’s Club™ Version 10/09 Page 30
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
COMPLETE SYSTEM BOX CONNECTIONS
Follow these procedures to correctly connect the various electronic components. Be sure the cables are connected securely and in working order. Use cable clamps, with appropriate tension, where necessary to ensure all cables stay in place during operation. Dress all cables with additional clamps and wire tie wraps where needed. Avoid loose wires or disconnected cables, as they can cause an unneeded service call.
ATTACH I/O POWER, AUDIO, AND USB CABLES.
♦ I/O board power cable. Connect from the I/O board to one of the two 4-pin power output connectors on the system box.
♦ Audio cables. Connect to the audio output jacks of the system box. Match the appropriate colors.
♦ USB cable #1. Connect from the I/O board to any USB port on the system box.
♦ USB cable #2 for future updates. Attach to any USB port on the system box. Route the other end to the control panel for easy access when updating.
♦ USB cable #3 for Cabinet Identification Device (CID). Refer to the CID Installation Section for proper orientation and placement of the CID.
♦ USB cable #4 for Card Reader (online option only). Connect to any USB port on the system box. The other end connects to the card reader.
ATTACH MAIN VIDEO CABLE
If your cabinet has a VGA or SVGA monitor, connect the video cable from the system box directly to the VGA or
SVGA monitor input.
If your cabinet has Medium or Low Resolution monitor, connect the video cable from the system box to the I/O board.
Be sure to adjust your Dip Switch settings to match your monitor’s resolution. Refer to Appendix D.
ATTACH POWER CABLE
Use the AC power cord that is currently in your cabinet. The cord plugs into the System box. Have a qualified electrician do the wiring. Verify A.C. main voltage selector switch is in the proper position. In North America the setting is 115 volts AC. In some countries this should be set at 230 VAC.
SOFT POWER / FAN CABLE
There is a “soft power” switch to turn your game on or off without reaching to the back of the cabinet. This switch is mounted on the back of the control panel, and comes in handy when performing any DVD updates. Connect one end of the Soft Power Cable to the Nighthawk System box. Route the other end to the switch located under the control panel. Locate the 3-Pin connector and plug it in to the Fan Cable.
Silver Strike Bowler’s Club™ Version 10/09 Page 31
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
COMPLETE I/O BOARD CONNECTIONS
CONNECT JAMMA HARNESS
Connect the JAMMA Connector to the I/O Board. Be sure it fits tightly and is oriented correctly.
CONNECT THE CONTROL PANEL SWITCHES AND CABLE
Snap the switches onto the buttons. Connect the Control Panel wiring harness using the JAMMA wiring chart found in Appendix B.
CONNECT COIN DOOR LAMPS
Connect the coin door lamp cable to the pigtail off the I/O Power cable. If your cabinet originally had a Golden
Tee Fore! green PCB, then use the 9-pin connector. If your cabinet had a Golden Tee Fore! red PCB, then use the 4 pin connector. Find the mating connector leading to the coin door to make your connection.
CONNECT THE TRACKBALL
Locate the Trackball Cable and connect it to the connector labeled Trackball on the I/O board. The other end will connect to the trackball. Connect the green earth ground wire to the trackball plate.
CONNECT ANTENNA
Locate the antenna cable and attach to the connector on the I/O board. A click should be heard if installed properly. Be sure the antenna is mounted vertically to achieve the widest signal.
Note: Use extreme care with this connector, as it is very delicate and can be damaged easily.
CONNECT AUDIO CABLES
Locate the Audio Cables already connected to the system box, and connect them to the I/O board audio inputs.
Inputs are color coded, so be sure to connect red to red, etc.
CONNECT THE USB CABLE
Locate the 6 ft. USB Cable from the system box and connect it to the USB port on the I/O board.
CONNECT MEDIUM OR LOW RESOLUTION MONITOR
If your cabinet has a Medium or Low Resolution monitor, you need to connect the video to the I/O board.
Connect the SVGA Video cable from system box to the J501 connector on the I/O Board. Connect the Red,
Green, Blue video outputs, the composite sync, and video ground from the JAMMA connector to the appropriate monitor inputs. To find the correct JAMMA pin outs refer to the diagram in Appendix B. Be sure to set the Video
Dip Switches on the I/O Board to match your resolution. Refer to the diagram in Appendix D.
CONNECT VGA OR SVGA MONITOR
VGA or SVGA monitors are connected directly to the system box video output. Do not connect a video cable to the I/O Board if you are using these resolutions.
CONNECT I/O POWER CABLE
Connect the I/O Power cable to the power input connector. Use the end with the pigtail. The other end connects to the system box.
CHECK ALL CONNECTIONS
Go over your entire cabinet again and double-check all of the connections. Make sure that all connectors are tight and secure and in their proper place. Look for frayed, broken or exposed wiring and repair as needed.
Bundle and wire-tie your wiring and secure it to the inside of the cabinet. A thorough and neat job now will save you a lot of time and trouble in the future.
Silver Strike Bowler’s Club™ Version 10/09 Page 32
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
CABINET GRAPHICS INSTALLATION
Included with your Silver Strike Bowler’s Club kit is a set of decals to place on the side of your cabinet and a brand new marquee. This will help identify your new game as Silver Strike Bowler’s Club. By placing and installing these correctly it can help give players instant recognition, even from a distance.
SIDE DECAL INSTALLATION
The following are the instructions on placing your side decals correctly on to the cabinet:
1. Locate the place where the side decals will be viewed best on your cabinet.
Refer to the diagram included on the decal sheet and to the right of these instructions for optimal placement.
NOTE: Make sure to have the sides of the cabinet as smooth and flat as possible, removing all previous residue from prior decals, to allow for a higher quality finish.
TIP: Liquid window cleaner can be sprayed onto the sides of the cabinet before placing the decals. The window cleaner will allow the decal to be removed and reinstalled without damaging the decal or adhesive. The decal roller or squeegee forces the cleaner out, leaving just the adhesive.
2. Remove the first of the new cabinet side decals from the backing.
3. Center the first decal on the location selected for your cabinet.
4. Using your hands (or a decal roller/squeegee), press down firmly starting from the center and smooth the side decal outward. Make sure all bubbles have been pressed out for a clean, flat surface.
5. Repeat for each of the remaining side decals.
MARQUEE INSTALLATION
The following are the instructions for placing the new marquee in your cabinet:
1. Using the old marquee glass as a template, center the glass on top of your new marquee. Make sure that all the printed images are visible.
2. Using an X-acto® knife or other sharp blade, score the new marquee deeply by following the edges of the old glass as a guide.
CAUTION: Do not cut on table or counter top. Use a cutting board or a disposable surface.
3. Carefully break off any excess material you have cut off.
4. Be sure the light behind the marquee works.
5. Clean the glass on both sides to give players a clear view of the new marquee.
6. Install the marquee graphics and glass securely.
Silver Strike Bowler’s Club™ Version 10/09 Page 33
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
FINAL CONNECTIONS
COIN DOORS, TEST SWITCH, AND VOLUME CONTROLS
Wire the coin doors as per the JAMMA Harness Connection table in Appendix B. Connect the door lamps to the appropriate (+12Vdc or +5Vdc) supply. Some games have separate power supply outputs for the lamps. Install a test switch somewhere convenient inside the coin door area. This switch allows you to enter adjustables, run diagnostics, and see or clear audits. Make it readily accessible through the coin door. Wire it to the Test wire on the JAMMA Harness. Silver Strike Bowler’s Club has the ability to adjust volume at any time during a game.
Install two push button switches (not included) inside the coin door for easy access. Connect the switches to the
JAMMA harness. Refer to the JAMMA Harness Connection table in Appendix B.
INITIAL POWER-UP
There are several steps you should take when powering up your Silver Strike Bowler’s Club for the first time. This is a quick checklist for you to follow when doing your first initial power-up:
Plug in the game and turn it ON; be sure the game powers up correctly into the attract mode.
Adjust volume levels to desired settings.
Adjust monitor settings for best picture.
NOTE: Sound and Video Tests are available through the System Tests Menu. They are beneficial when making any adjustments. Proper monitor and sound adjustment is very important.
Try all money slots. Drop quarters or tokens through to check the coin mechs and insert a bill into the bill acceptor. Make sure the game is adding credits.
NOTE: Silver Strike Bowler’s Club supports most bill acceptors. Installing a bill acceptor is highly recommended and will increase your earnings. Refer to your bill acceptor's manual for installation specifications. The bill acceptor can be wired to coin door 3 on the JAMMA.
Test all of the player input controls. You can use the PLAYER CONTROL TESTS in the SYSTEM SETUP
MENU.
Upon initial power-up the game is set to factory default settings. These settings affect game elements such as value per coin, volume settings, etc. The OPERATOR MENUS section will describe how to alter these settings for your location.
Congratulations! You have finished installing Silver Strike
Bowler’s Club!
Silver Strike Bowler’s Club™ Version 10/09 Page 34
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
SYSTEM SETUP MENUS
Navigating The Menu System
The System Setup menus cover a variety of important areas including collections, tests, game adjustments, and optional settings. You should familiarize yourself with these menus, as they are designed to optimize your game for your location and your business. Pay particular attention to the Collection menus, as they will detail how much money to give to your location, and how much money to set aside for ITNet. There are also menus that allow you to adjust various split percentages for a variety of different charges. These screens can help you maximize your investment and involve your location in the costs associated with your equipment.
Entering System Setup Mode
There are two ways to enter System Setup. Open the coin door and press the Test button to access the game’s
System Setup software menu system. Or, from the I/O board, move the dip switch SW202 position 4 to the ON position. This switch needs to be moved back to OFF to exit the System Setup menus.
Selecting a Menu
A menu option can be selected at any time by rolling the trackball up or down or by pressing the Left or Right buttons.
Choosing a Menu/Option
A menu option can be chosen at any time by pressing the Start Button.
Changing a Value
A value can be changed at any time by rolling the trackball left or right.
MAIN MENU
The Main Menu displays five main areas that make up System Setup mode. Please familiarize yourself with these areas, as they will help you maximize your earnings potential.
Collections & Earnings
This section displays your machine’s monetary activity, and details the various areas for income and expenses. This section should be reviewed during every collection, to make sure you manage your split correctly.
General Settings
This area allows you to adjust operator adjustables, perform system tests, and reset your game back to factory settings.
Troubleshooting Shortcuts
This section presents a variety of tests and menus that will help you troubleshoot any problems you may be having with your game. The available sections are also accessible through the other main sections.
Silver Strike Settings
This area allows you to adjust settings specific to Silver Strike Bowler’s Club including the player cost schedule, game features, and game audits.
Silver Strike Bowler’s Club™ Version 10/09 Page 35
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
ITNet Settings (online only)
This section details various ITNet settings, such as game registration and connection settings with ITNet.
Exit
This will exit the System Setup menus and take you back into the game’s attract mode.
COLLECTIONS & EARNINGS MENU
This menu allows you to perform a collection or view various earnings and fees.
Do Collection
This section is used when making a collection. The various screens will detail the cost breakdowns and show you how much of the cash box is to be paid to the location. Please take some time to familiarize yourself with this section. Using it wisely can save you money.
Clear Unused Cash
Sometimes when you go to make your collection, there is money in the game that has not been played yet. Use this setting to clear the unused cash from the game, so your future collections will reconcile with game play.
Add Free Cash
Use this setting if you wish to add money to the game for free plays that do not advance the hard meter.
Back
This will take you back to the Main Menu.
DO COLLECTION
This screen is the main collection screen. There is a lot of helpful information displayed that will help you with your collection. It is highly recommended that you view this screen with every collection, and reset it when your collection is complete.
This screen displays the following helpful information:
Collection Date Range
The displayed dates are from your last collection until today.
Days In Operation
The number of days the machine was active and available for play since the last collection.
Reset
Highlight this to reset the number of days in operation field to ‘0’.
Total Income
The total income your machine made for this time period.
More Details
Select More Details to display a breakdown of Total Income, including income from Cash, Player Accounts and various promotional or Gift Cards.
Silver Strike Bowler’s Club™ Version 10/09 Page 36
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Total Fees
The total of the various fees that need to be set aside before making your split.
More Details
Select this to display a breakdown of the various fees, including the ITNet fees, Communication fees, Software
Update fees, Hardware Upgrade fees and Taxes.
Note! Software Update Fees and Hardware Update Fees are included for your convenience, to help you cover the costs of owning and operating your equipment. These two line items are NOT included on your monthly ITNet statement.
Balance
The total income minus the total fees.
Operator Portion of Balance
The amount of the collection that the operator keeps.
Operator Owes Location
The amount of the collection that you pay your location.
Back
If you do NOT wish to perform a collection and reset the audits, highlight Back to exit this screen and return to the
Collections & Earnings menu.
Do Collection and Exit
If you wish to perform a collection and reset the audits (recommended), highlight Do Collection and Exit and press
Start. This will set all the fields in the Do Collection screen to zero. Be sure to empty your cash box at the same time, so these screens will match the money at your next collection.
GENERAL SETTINGS
The General Settings menu houses various adjustable settings relating to the cabinet, and is divided into three sections.
Operator Adjustables
This area allows you to adjust options like volume, attract mode sounds, and money slot settings.
System Tests
This area allows you to perform diagnostics including video adjustments, input tests, and sound tests.
Advertisements
This area allows you to manage various graphic and text advertisements on your machine. This section is currently unavailable but is planned for a future update.
Back
This will take you back to the Main Menu.
Silver Strike Bowler’s Club™ Version 10/09 Page 37
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
OPERATOR ADJUSTABLES
This menu contains adjustable settings that pertain to you and your business. Please familiarize yourself with this section, as it can help you maximize the game’s earning potential.
General Adjustments
This area allows you to adjust options like coin message, game mode and monitor mode.
Money Slot Adjustments
This area allows you to adjust the settings of your various money slots on your cabinet.
Sound Adjustments
This area allows you to adjust the various sound settings including attract mode sounds, game volume, and stereo setup.
Collection Settings
This important area allows you to adjust various fees and splits for your collections.
Reset To Factory Settings
This option allows you to reset all the settings found in the Operator Adjustables section to factory defaults.
Back
This will take you back to the General Settings menu.
GENERAL ADJUSTMENTS
Coin Message
Is set to “Insert $” by default and requires the player to insert money. No other modes are available.
Game Mode
This lets you toggle between money/free play. The default
is set to Money Play.
2
nd
Monitor Mode
You can connect a second monitor to the extra video connector on the system box, which is great for promotions or special events. Select S-Video if your second monitor is a television screen, or SVGA if your second monitor is an
RGB monitor. The default setting is S-Video.
Reset Values
This resets all values to their default value located on this page.
Back
This will take you back to the Operator Adjustables menu.
Silver Strike Bowler’s Club™ Version 10/09 Page 38
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
MONEY SLOT ADJUSTMENTS
Money Slot 1 (all machines)
This adjusts how much one pulse equals for Money Slot 1.
The default is set to $0.25.
Money Slot 2 (kits only)
This adjusts how much one pulse equals for Money Slot 2.
The default is set to $0.25.
Money Slot 3
This adjusts how much one pulse equals for Money Slot 3.
The default is set to $0.25.
Reset Values
This resets all values to their default value located on this page.
No
This will not perform the reset and take you back to the previous menu.
Yes
This will perform the reset and take you back to the previous menu.
Back
This will take you back to the Operator Adjustables menu.
SOUND ADJUSTMENTS
In Game Volume
This option lets you adjust the In Game volume from OFF to 100%. The default is set to 30%.
Attract Volume
This option lets you adjust the Attract Volume from OFF to
100%. The default is set to 20%.
Attract Mode Sounds
This adjusts how often sounds are played in the attract mode: Never, Rarely (every 20th time), Sometimes (every
10th time), Often (every 5th time), and Always. The default
is set to On - Sometimes.
Stereo/Mono
This option is where you select stereo or mono setup. The
default is set to Stereo.
Reset Values
This resets all values to their default value located on this page.
Back
This will take you back to the Operator Adjustables menu.
Silver Strike Bowler’s Club™ Version 10/09 Page 39
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
COLLECTION SETTINGS
Silver Strike Bowler’s Club allows you to adjust costs and percentages for the various income types that are received.
Use this menu to determine how much you want your location to help you pay for these charges and services.
Set Hardware Update Fee
This menu allows you to adjust the Hardware Update Fee.
This fee is included for your convenience, as a method to have the location pay for part of your equipment. The default value is $0.00 per week.
Note! Hardware and Software Update Fees are included for your convenience, and are NOT included on your monthly ITNet statement.
Operator/Location Income Splits
Use this menu to fine-tune your splits for any generated income. Since there may be times when you have to pay the location before you actually have the cash in hand, you may want to adjust the split in your favor to cover the waiting period. The default settings are displayed on the accompanying screen.
The adjustable settings refer to income generated from:
Cash
Player Account (online only)
ITNet Money Card (online only)
Operator Money Card (online only)
Operator/Location Fee Splits
Use this menu to determine how you wish to split the various fees with your location. For example, since there is a fee associated with ITNet, you may want to adjust the split in your favor to help cover the costs.
ITNet Fees (online only)
Communication Fees (online only)
Software Update Fees (online only)
Hardware Update Fees
Note! Hardware and Software Update Fees are included for your convenience, and are NOT included on your monthly ITNet statement.
Silver Strike Bowler’s Club™ Version 10/09 Page 40
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Tax Settings
Many states require special taxes or license fees that affect your bottom line. Use this menu to separate these costs from your collection before making your normal split.
Set Tax Rate
This menu allows you to adjust your current tax rate percentage.
Set Tax Type
This menu helps you determine what part of the collection is taxed, and who pays for these taxes.
Set Tax Split
This menu allows you to split the tax fees with the location.
Reset to Defaults
This menu will set all of the collection settings to their factory default values. A verification screen will display to make sure you agree to the change.
Back
This will take you back to the Collection Settings menu.
RESET TO FACTORY SETTINGS
This menu will reset ALL settings in the Operator
Adjustments section to their default values. A verification screen will display to make sure you agree to the change.
Silver Strike Bowler’s Club™ Version 10/09 Page 41
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
SYSTEM TESTS
This area allows you to perform diagnostics including video adjustments, input tests, and sound tests.
Video Tests
This area has tests that will help you to adjust your game’s color, contrast, and screen size.
Sound Tests
This area has tests that will help you adjust your game’s audio setup by playing a stored sound, a streaming sound, and testing the speaker(s).
Player Control Tests
This option allows you to test all inputs including trackball, buttons, money slots and card reader.
Mechanical Meter Test
This test makes the hard meter adjust by one to make sure it is functioning properly.
Hardware Tests
This area includes a series of diagnostic screens and tests to help you make sure your game is functioning correctly.
Back
This will take you back to the General Settings menu.
VIDEO TESTS
The Video Tests section has a variety of tests that will help you adjust your monitor.
Color Adjustments
This area will take you to a series of tests to adjust your monitor’s RGB settings to have each color display properly.
Contrast Adjustments
This area will take you to a series of tests to adjust your monitor’s brightness/contrast so the game displays properly.
Screen Size Adjustment
Use this screen to align your monitor so that all the circles appear as circles and the boundary line appears on the edge of each side of the screen.
Back
This will take you back to the System Tests menu.
Silver Strike Bowler’s Club™ Version 10/09 Page 42
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
COLOR ADJUSTMENTS
Color Grid Adjustment
Adjust your monitor to have each colored box display properly.
Red Screen
Adjust your monitor to have red display properly.
Green Screen
Adjust your monitor to have green display properly.
Blue Screen
Adjust your monitor to have blue display properly.
Back
This will take you back to the Video Tests menu.
CONTRAST ADJUSTMENTS
White Screen
Adjust your monitor to have white display properly.
50% White Screen
Adjust your monitor to have 50% white display properly.
25% White Screen
Adjust your monitor to have 25% white display properly.
Black Screen
Adjust your monitor to have black display properly.
Contrast Screen
This option is a test you can use to adjust your monitor’s contrast and brightness settings to have the boxes displayed properly.
Note: May not work on older or often used monitors .If you have a monitor that's old or has been used often you may not be able to adjust the contrast and/or brightness levels accordingly. In this case adjust the monitor for best performance while getting close to the recommended settings.
Back
This will take you back to the Video Tests menu.
SCREEN SIZE ADJUSTMENT
Use this screen to adjust the size and aspect ratio of your picture. Press the Start button to exit.
Silver Strike Bowler’s Club™ Version 10/09 Page 43
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
SOUND TESTS
Stored Sound
This will play a stored sound so you can make sure your audio setup is functioning properly.
Streaming Sound
This will play a streaming sound so you can make sure your audio setup is functioning properly.
Speaker Test
This test will say MONO if you have your game set to Mono or LEFT and RIGHT if you have it set to stereo so you can make sure your audio setup is functioning properly.
Back
This will take you back to the System Tests menu.
PLAYER CONTROL TESTS
Use this screen to test all of the inputs, including the trackball, buttons, money slots and card reader. When an input is active the appropriate graphic image will light.
Press the Left, Right and Start buttons simultaneously to exit this test screen.
MECHANICAL METER TEST
Click Meter
This test makes the hard meter adjust by one to make sure it is functioning properly.
Back
This will take you back to the System Tests menu.
Silver Strike Bowler’s Club™ Version 10/09 Page 44
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
HARDWARE TESTS
This area includes a series of diagnostic screens and tests to help you make sure your game is functioning correctly.
Hardware/Software
This area has options to view your system and USB info.
Check Hard Drive
This test checks the integrity of your hard drive’s data.
Note: This test can take several minutes.
Check Cooling
This test helps you make sure your game is functioning at the proper temperature and all fans are working.
Check Card Reader
This test will test the functionality of the card reader, and display some details on the card that is tested.
Back
This will take you back to the System Tests menu.
HARDWARE/SOFTWARE
System Info
This is a list of your game’s current basic system info.
USB Info
This is a list of your game’s current USB devices.
Version Info
This is a list of your game’s software version.
Back
This will take you back to the Hardware Tests menu.
SYSTEM INFO
This is a list of your game’s current basic system information, including Hard Drive, CPU and Video Card.
USB INFO
This is a list of your game’s current USB devices.
VERSION INFO
This is a list of your machine’s software version.
Silver Strike Bowler’s Club™ Version 10/09 Page 45
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
CHECK HARD DRIVE
Check File Data
This test checks the integrity of your hard drive’s data.
Select Begin Test to initiate the process.
Note: This test can take up to 3 hours to complete.
If this test succeeds you will see the message: Status:
Hard Drive Functioning Properly. If this test fails, you will see the message: Hard Drive Error (#)
Select Back to skip the test and return to the Hardware
Tests menu.
Check File System
This test REBOOTS YOUR GAME and performs a low level systems check of the integrity of your hard drive.
Note: This can take several minutes.
Back
This will take you back to the Hardware Tests menu.
CHECK COOLING
This checks that your game is functioning at the proper temperature and all fans are working. The current status is color-coded for easy viewing. If the results are displayed in green, your cabinet is at normal settings.
NOTE: Cooling information on your system may show up as dashed lines just as shown in the picture. This is because some motherboards do not allow external access to the temperature and fan speeds. This should not be considered a problem.
Back
The Back button takes you back to the Hardware Tests menu.
CHECK CARD READER (ONLINE
ONLY)
This test will check to see if your card reader can read and recognize properly encoded IT and credit cards.
From this screen, insert a card into the card reader. If the card can be read, a message will appear on the screen.
The best way to run this test is to use 3 different cards, with at least credit card. Alternate swiping each card about 10 times each. A misread every so often is not uncommon. If it the results are good more often than bad, the card reader is working properly.
Back
The Back button takes you back to the Hardware Tests menu.
Silver Strike Bowler’s Club™ Version 10/09 Page 46
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
TROUBLESHOOTING SHORTCUTS
This section gathers many of the commonly used tests and menus into one convenient area. Check here first when troubleshooting problems or questions about the integrity of your machine.
The tests that are available in this section are:
Check Card Reader (online only)
Check Cooling
Check Hard Drive
Hardware & Software
Communications Settings (online only)
Player Control Tests
System Tests
Descriptions of each of these tests and sections can be found elsewhere in this manual.
Back
This will take you back to the Main Menu.
SILVER STRIKE SETTINGS
Player Cost Schedule
This option allows you to adjust the amount of money it costs a player to play various game types.
Game Audits
This area allows you to view your money audits, game purchase audits, and reset your collections and audits.
Game Options
This area allows you to adjust options specific to Silver
Strike Bowling.
Reset Leaderboards
This will clear all of the game’s local leaderboards and highscore screens.
Ticket Dispenser
This area allows you to set and adjust optional ticket dispenser values and settings.
Back
This will take you back to the Main Menu.
Silver Strike Bowler’s Club™ Version 10/09 Page 47
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
PLAYER COST SCHEDULE
This screen details the costs of various play selections. The player cost is shown as a total, with the Operator Portion and the ITNet Portion broken out.
Single Play
This option lets you adjust how much it costs a player to play a single 10-frame game of bowling. The default is set to $1.00.
Series Play
This option lets you adjust how much it costs a player to play a
3-game series. The default is set to $2.50.
Throwdown
This option lets you adjust how much it costs a player to play a single game of Throwdown, the bracketed contest mode for 4, 8 or 16 players. The default is set to $2.00 per
player.
SSB Survivor
This option lets you adjust how much it costs a player to play a Survivor game. The default is set to $0.50.
3-Frame Practice
This option lets you adjust how much it costs a player to play a 3-frame practice game. The default is set to
$0.50.
3-Frame Buy In
This option lets you adjust how much it costs a player to buy a second set of 3 frames. The default is set to $0.50.
View Fixed Costs
Selecting View Fixed Costs displays payment settings and splits for some items that are not adjustable.
Player’s Card Purchase
Reset Defaults
This resets all values to their default value located on this page.
Back
Select this to return to the Silver Strike Settings menu.
Silver Strike Bowler’s Club™ Version 10/09 Page 48
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
GAME AUDITS
This section displays various counts and totals for a variety of areas of interest. The following values are based on the last reset, the date of which is shown at the top of the screen.
Coin Slot 1 (All Machines)
Coin Slot 2 (Kits only)
Bill Acceptor
Lifetime Money In
This field shows how much total money your machine has made since its initial registration with ITNet. This field is cumulative and is not affected by resetting the audits on this screen.
Bowlers Club Cards Purchased
Number of Tickets Paid
Ticket Value %age Payout
More
The available audits span a number of different screens. Selecting More brings you to the next page of audit information. In total there are seven pages of audits.
Reset Audits
This will reset the fields on all seven audits screens to zero, and update the date of the last audit reset. The
Lifetime Money In field will not be affected by this function.
Silver Strike Bowler’s Club™ Version 10/09 Page 49
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
GAME OPTIONS
Game Options presents a variety of game-specific features that can be turned on or off based on the needs of your location.
Vegas Bowling
This is a selectable game mode that displays cards for every mark earned. Turn this option off in areas where the display of playing cards is not allowed.
Buy Player Cards
Players can order Silver Strike Bowler’s Club Cards from the game, that can be used for identification purposes.
Sweepstakes
Players are entered into a national weekly drawing every time they play an identified game of Silver Strike
Bowler’s Club. Turn this option off in areas where sweepstakes are not allowed.
Announce Volume
Adjust the volume of the sweepstakes announcement here.
Reset Values
This will reset the fields on all game option menus to their default settings.
More
The available options are displayed on two screens. Selecting More brings you to the next page of game options.
Delay Timeout
This sets the amount of time allowed before any player input is noticed. If the timer runs out before a player moved or the ball is thrown, the ball will be lost. Use this in conjunction with the Ball Timeout setting below to determine when a game is terminated due to timeout.
Ball Timeout
This adjusts the number of balls allowed before ending an unattended game. See Delay Timeout above.
3-Frame Practice
This setting turns the 3-frame game option on or off. The default setting is Off.
Survivor # Misses
This setting adjusts the settings for the new Survivor Mode.
If you want players to have a longer play experience, adjust the number of missed strikes to a higher number. If you want players to be eliminated faster, adjust the number of missed strikes to a smaller number. The default setting for this game feature is 3.
Reset Values
This will reset the fields on all 3 game options menus to their default settings. The Lifetime Money In field will not be affected by this function.
Silver Strike Bowler’s Club™ Version 10/09 Page 50
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
RED PIN BONUS FREE GAME
Once the Red Pin Bonus Free Game mode is turned on, operators will have the option to set the number of consecutive Red Pin strikes needed for a free game award.
Use the menu settings to award a free game for anywhere from one Red Pin strike to 8 consecutive Red Pin strikes.
Note that the default for this feature is OFF.
Reset # Games Awarded
This will reset the number of free games awarded to zero.
Reset Values
This will reset the fields on all game option menus to their default settings.
RESET LEADERBOARDS
Use this menu to clear the leaderboards or high-score screens. You can reset individual leaderboards or all of them at once.
TICKET DISPENSER
Silver Strike Bowler’s Club supports the addition of optional ticket dispenser. Use this menu to set up and test your dispenser, and apply values to the tickets for a variety of award options.
This option will only work if an optional ticket dispenser is installed. Be sure to set the Ticket Dispenser setting to ON from the Dispenser Settings menu.
Silver Strike Bowler’s Club™ Version 10/09 Page 51
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
ITNET SETTINGS (ONLINE ONLY)
This section details various ITNet settings, such as game registration and connection settings with ITNet.
Change Location/Register Game
This section lets you update the information for the location that your game is currently in and send it to ITNet.
If your machine is unregistered, the screen will display
Register Game. If your machine is already registered, the screen will display Change Location.
Note: These sections require an Operator ID Card to activate.
Note: These sections require a working connection to ITNet.
Communication Settings
This section lets you select and adjust various communication options.
Connection Tests
This section tests your communication connections for integrity and reliability.
Re-Activate Modem
This section gives you the ability to use a special Modem Reactivation Card if your modem is currently unregistered.
Back
Select this to return to the Main Menu.
CHANGE LOCATION
Select this option and insert your Operator ID Card into the Card Reader. If the machine is properly registered, you will be asked to enter the zip code of the location the machine is placed in. The zip code is very important and is used to find the most optimal wireless service available. Once the zip code is entered, the machine will contact ITNet for a list of available cities. Verify that the city and zip code are accurate.
Next enter the name and phone number of the location. This information will be used to identify the game and will be posted on the Silver Strike website, so players can find and play on your machines. Verify that all information is accurate. Once complete, exit the screen to complete the location change process.
Silver Strike Bowler’s Club™ Version 10/09 Page 52
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
COMMUNICATION SETTINGS
This screen shows the type of communication device that is currently in use, and its status and signal strength. In most cases, the wireless modem will be in use and active. If your machine is in a location with low signal strength, check the Troubleshooting section of the manual for ways to help boost your signal.
Configure Ethernet Settings
If your machine is in a location with low signal strength, and none of the suggestions on boosting your signal help, you may need to connect to ITNet using a broadband connection through Ethernet.
Back
Select this to return to the ITNet Settings menu.
CONNECTION TESTS
Use this section to test the connection to ITNet.
Check Latency Time
This test will measure the time it takes for your game to communicate with ITNet. If successful, the delay time in seconds will be displayed.
Force Call to ITNet
This test will initiate a connection with the ITNet system and give a result status.
Back
Select this to return to the ITNet Settings menu.
RE-ACTIVATE MODEM
Once your machine is registered, your wireless service is active regardless of how much play or activity is on the machine. If you must un-register your machine to avoid wireless modem service charges, the wireless modem will be made inactive.
When you wish to once again register the machine, you will need a special Modem Reactivation Card to make your modem viable again. These special, one-time-use cards are encoded specifically for a machine and are created by
IT on an as-needed basis. Allow 2 weeks to receive your card from Incredible Technologies.
Once you receive your Modem Reactivation Card, access this menu and insert the card into the card reader. Be sure the number on the card matches the number on the screen.
The process can take several minutes and is sensitive to signal strength. Watch the progress bar as the reactivation process takes place. Once complete, a status message will appear. If the reactivation was unsuccessful, try again. If subsequent attempts are unsuccessful, write down the error code and contact the IT tech department for assistance.
Silver Strike Bowler’s Club™ Version 10/09 Page 53
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
SILVER STRIKE BOWLER’S CLUB
TROUBLESHOOTING & REFERENCE
APPENDIX A
TROUBLESHOOTING GUIDE
Video Problems
Symptom
No picture on 27” Monitor
No picture but game sounds are heard
Scrambled Picture
Entire picture is not seen on the screen or it does not fill the entire screen
Missing or washed out colors
Probable Cause
I/O Board Dip Switch settings are wrong.
Incorrect video connection configuration.
Monitor does not have a proper
A.C. voltage input.
Monitor is defective. working on a known good system.
Repair or replace.
Nighthawk System box is defective Go to Nighthawk System box troubleshooting section.
Incorrect video connection configuration.
Since you hear game sounds the system is working.
I/O board Dip Switch settings are set wrong.
Be sure the video connections are correct according to the type of monitor you are using. Refer to the diagrams in Appendix D.
Verify A.C. power to the Nighthawk
System box. Verify monitor is
Verify video is connected to the system correctly. Refer to the diagrams in Appendix D.
Review no picture troubleshooting section above.
Adjust Dip Switch settings to match the resolution of the monitor you are using. Refer to Dip Switch Settings in Appendix D.
Incorrect video connection configuration.
Solution
Adjust Dip Switch settings to match the resolution of the monitor you are using. Refer to I/O Dip Switch
Settings in Appendix D.
Misadjusted monitor.
Bad Video connections
Be sure the video connections are correct according to the type of monitor you are using. Refer to the diagrams in Appendix D.
Adjust the monitor width and height.
Use video screen adjustment in system tests. Refer to the monitor manual.
Verify continuity from the monitor to the video out on the I/O board. Red,
Green, Blue video signal. Mid. and
Low resolution monitors only.
Contrast and brightness on the monitor needs to be adjusted.
Defective Monitor.
Refer to the monitor manual to make adjustments.
Verify by connecting a known good monitor to the system.
Silver Strike Bowler’s Club™ Version 10/09 Page 54
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Wireless Connection Problems
Symptom
Low Signal Strength
See Appendix F for more information.
Probable Cause
Placement in location is impeding the signal.
Antenna needs to be repositioned for best signal strength.
Solution
Place the game near a window or doorway to yield a better signal.
Adjust the orientation of the Antenna within the cabinet. Be sure the antenna is vertical(straight up and down) Sometimes a slight tilt in one direction will help.
Rotate the Antenna 180 degrees.
Reposition the Antenna to the opposite side of the cabinet. See
Appendix F for hints on methods for optimal signal strength.
Signal strength in location is weak. Add a signal booster. In many instances a booster can be added for an additional charge. Please call customer service for more information. P/N 900100510
Sound Problems
Symptom
No Sound
Probable Cause
Audio Cable between the I/O board and the Nighthawk system box are not connected.
Speakers are not connected properly.
Solution
Verify audio cables are connected.
Refer to Appendix D.
Volume is set to the lowest level.
Attract mode sounds may be set to all off. You will have sounds when playing the game.
Defective I/O board.
Defective Nighthawk system box.
Distorted or scratchy game sounds Bad speaker.
Loose speaker or grill cover is causing vibration.
Loose/defective audio cables from the Nighthawk system box to the
I/O board.
Defective I/O board.
Verify continuity from the I/O board speaker output pins to the speakers.
Refer to Appendix D.
Adjust the volume to an audible level.
Choose one of the 5 Attract Mode sound options in Sound
Adjustments.
Verify on a known working system.
Replace if necessary.
Be certain all other possibilities are explored before replacing the
Nighthawk system box.
Replace blown speaker.
Verify all components are installed properly and securely.
Check the audio cable connections.
Replace cable.
Defective Nighthawk system box.
Verify on a known working system.
Replace if necessary.
Be certain all other possibilities are explored before replacing the
Nighthawk system box.
Silver Strike Bowler’s Club™ Version 10/09 Page 55
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Nighthawk System Box Problems
Symptom
No video and no green lights on the I/O board. Fans are not heard on the Nighthawk System box.
No video and no green lights on the I/O board. Fans are heard on the Nighthawk System box.
Probable Cause
No A.C. power to the Nighthawk system box.
Power switch on the Nighthawk system box is off.
Solution
Verify A.C. voltage is connected to the Nighthawk system box.
Flip the Nighthawk system box power switch to on.
Main cabinet power switch is off. Be certain the main cabinet switch is set to on.
Defective Nighthawk system box. Be certain all other possibilities are explored before replacing the
Nighthawk system box.
DC power cord not connected from
Nighthawk system box to I/O board.
Defective I/O board.
Connect the DC power cord from the
Nighthawk system box to the I/O board.
Try it on a known good system.
Verify by disconnecting all cables from the I/O board except the DC power and USB cable to the
Nighthawk system box. No green lights, replace the I/O board.
Control Problems
Symptom
Button does not work.
Probable Cause
Switches Common post is not connected to digital ground.
Signal wire is not connected to the
Normally Open post of the switch.
Switch is defective.
Signal wire is connected to the
Normally Closed post of the switch.
Solution
Verify continuity to digital/power supply ground.
Verify continuity from the I/O board to the Normally Open post of the switch.
Replace defective switch.
Connect signal wire to the Normally
Open post of the switch.
Button always indicates closed in the player control test. Pressing it will show it is not depressed.
Button always indicates closed in player control test even with the switch disconnected entirely.
Trackball is not functioning in any direction.
Defective I/O board.
Trackball is not connected to the
I/O board properly.
Test on a known good system.
Replace if necessary.
Trackball does not work in a certain direction.
Trackball works intermittently.
Defective trackball Interconnect cable.
Trackball is defective.
I/O board is defective
Trackball cable is defective.
Trackball is defective.
I/O board is defective.
Inside of the trackball is dirty.
Rollers are worn.
Trackball is over-tightened.
Verify the trackball is connected to
J208 labeled trackball on the I/O board.
Verify continuity on the trackball
Interconnect cable.
Replace trackball.
Replace I/O board. Try it on a known good system.
Verify continuity on the trackball cable. Repair or replace if needed.
Repair or replace the trackball. Try it on a known working system.
Repair or replace the I/O board. Try it on a known working system.
Clean the inside of the trackball.
Replace the rollers and bearings.
Do not over-tighten the trackball.
Tighten just enough to flatten the lock washers.
Silver Strike Bowler’s Club™ Version 10/09 Page 56
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Error Messages
Symptom
Most on screen error messages explain themselves.
Flash code 6 on I/O board Diode
D102
Please turn game off, then connect
Cabinet Identification Device (CID) then turn game back on.
Probable Cause
Multiple
CID is not connected or is defective
CID is not connected
CID cable is defective
Solution
Follow the onscreen instructions.
Many times turning the game off for ten seconds and then turning it back on will solve the error.
Check the USB cable connection.
Swap with a known good cable. Call
I.T. Service for further assistance.
Connect CID to the Nighthawk system box via USB cable.
Try or swap with a known good USB cable.
I.T. service will instruct you what to do.
Connect USB Cable. Flash code 1 on I/O board diode
D102
Please turn game off, Then connect USB I/O board and then turn game back on.
If LED is not flashing - Call I.T.
Service
This indicates to USB connection fail from System box to I/O board.
USB cable is not connected
USB cable is Defective
I/O board has no power connection.
I/O board is defective
Connect the USB cable.
Try with a known good USB cable.
Verify power to the I/O board.
Swap with a known good I/O board.
Possibly bad. Call I.T. service.
Flash Code Messages
Flash Code (I/O Diode D102)
Flash code 2
Code Description
This indicates to USB connection fail from System box to I/O board.
INFO: Last reboot due to
Watchdog time out.
Solution
Connect USB Cable.
Flash Code 3
Flash Code 4
Flash Code 5
Flash code 6
Flash Code 7
Flash Code 10
Flash Code 11
Flash Code 12
Flash Code 13
Flash Code 14
Error when updating USB CID to latest version.
Updated USB CID was detected.
CID is not connected or is defective
CID Malfunction.
Error when updating USB I/O
Board to latest version.
Updated USB I/O Board was detected.
I/O Board is disconnected.
I/O Board malfunction.
Incompatible I/O Board.
Turn off game, wait 10 seconds, turn game on. If the problem persists call IT tech support.
Turn off game, wait 10 seconds, turn game on. If the problem persists call IT tech support.
Turn off game, wait 10 seconds, turn game on. If the problem persists call IT tech support.
Check the USB cable connection.
Swap with a known good cable. Call
I.T. Service for further assistance.
Make sure all connections are in place. Turn off game, wait 10 seconds, turn game on.
Turn off game, wait 10 seconds, turn game on. If the problem persists call IT tech support.
Turn off game, wait 10 seconds, turn game on. If the problem persists call IT tech support.
Make sure all connections are in place. Turn off game, wait 10 seconds, turn game on.
Make sure all connections are in place. Turn off game, wait 10 seconds, turn game on.
Make sure all connections are in place. Turn off game, wait 10 seconds, turn game on.
Silver Strike Bowler’s Club™ Version 10/09 Page 57
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Miscellaneous Problems
Symptom
Unable to exit Operator Menus.
No fluorescent light
Coin Meter is not working
Probable Cause
Dipswitch SW202 position 4 is in the on position.
Test switch wired from the I/O board is closed.
No 120 volts A.C. power going to the light fixture.
Defective fluorescent light.
Defective starter
Defective ballast.
Defective Coin Meter
Not wired properly
Defective I/O board
Solution
Set position 4 of SW202 to off.
Press start to exit.
Verify satellite test switch is not closed.
Verify A.C. voltage to the light fixture.
Replace fluorescent light.
Replace the starter.
Replace the ballast.
Replace with a known good one.
Connect one lead to +5 or +12 volts depending on device. The other lead to count 1 on the JAMMA connector.
Replace with a known good board.
Silver Strike Bowler’s Club™ Version 10/09 Page 58
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
APPENDIX B
JAMMA, TRACKBALL, AND I/O POWER CONNECTIONS
JAMMA Harness Connection
SOLDER SIDE PARTS SIDE
KEY
WIRE COLOR
Yellow-Green
White-Green
Green-Black
White
Green-Blue
Orange-Yellow
Black
FUNCTION
*
*
*
*
*
Count 2
Left Speaker (-)
Right Speaker (-)
Video Green
Video Sync
Coin 2
Volume Down
GND
K
L
M
N
E
F
H
J
A
B
C
D
P
R
S
T
U
1
2
3
4
5
6
7
8
*
*
*
*
*
KEY
FUNCTION
Coin Counter
9
10 Left Speaker (+)
11 Right Speaker (+)
12 Video Red
13
14
15
Video Blue
Video GND
Test
16 Coin1
17 Start 1
WIRE COLOR
Red-Green
Yellow-Red
White-Red
Red-Black
Blue-Black
White-Black
Blue
Red-Blue
Red-White
Z
A
B
C
V 18
W 19
X
Y
20
21
Player 1 – Ball Weight
Player 1 – Overhead
Purple-White
Violet-White
D
E
22
23
24
25
26
27
Player 1 – Left
Player 1 – Right
Volume Up
Coin 3 (Bill)
GND
Brown-White
Yellow-White
Orange-White
Gray-White
Black
Black GND F 28 GND Black
*NOTE: Power is NOT routed through the JAMMA connector.
Trackball Harness Connector Pin Outs
I/O Board Connector Trackball Connector
PIN WIRE #6 - Black PIN WIRE #1 – Black
I/O Power Cable Pin Outs
Pin Number
1
Wire Color
Yellow
Function
+ 12 Volts DC
PIN WIRE #1 - Red
PIN WIRE #2 - Yellow
PIN WIRE #3 - Green
PIN WIRE #2 – Red
PIN WIRE #3 – Yellow
PIN WIRE #4 – Green
2
3
4
Black
Red
Black
Ground
+ 5 Volts DC
Ground
PIN WIRE #5 - Blue
PIN WIRE #4 - Purple
PIN WIRE #5 – Blue
PIN WIRE #6 – Purple
Silver Strike Bowler’s Club™ Version 10/09 Page 59
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
APPENDIX C
REPLACEMENT PART NUMBERS
Please refer to these IT part numbers when placing orders.
Part Number Description
900910050 ANTENNA, COMPLETE KIT
750250201 ANTENNA, COVER
510000900R ANTENNA, W/CABLE FOR WIRELESS MODEM
900196007R CABINET IDENTIFICATION DEVICE, BOWLER'S CLUB
960000288 CABINET, DEDICATED BOWLER’S CLUB CABINET ASSY ONLY
915000285R CABLE ASSY, AUDIO CABLE, 6 FT 2RCA PLUG TO 2RCA PLUG
915250304R CABLE ASSY, I/O POWER FOR KITS
915000745 CABLE ASSY, POWER CORD. A.C.
915000315R CABLE ASSY, SVGA, 6 FT. DB15HD M-M
915000310R CABLE ASSY, USB CABLE, 6 FT.
915000173R CABLE ASSY, TRACKBALL/GUN INTERFACE
752007102R CARD READER BEZEL, METAL
900007104 CARD READER SUB-ASSEMBLY, USB WITH BEZEL AND HARDWARE
760007104R CARD READER, MODEL 7104USB TWO TRACKS, WITH LEDS
900288715 CASH VAULT, COMPLETE ASSY W/ CARD READER AND DBA
999000715 CASH VAULT, HOUSING ONLY (NO CARD READER OR DBA)
825100265R CONTROL PANEL OVERLAY, DIECUT WITH CONTROL LABELS/TB HOLE
845000288R CONTROL PANEL PLEXI FOR SSBC DEDICATED ONLY
753000250 CONTROL PANEL, RUBBER BUMPER FOR DEDICATED ONLY
900265100 CONTROL PANEL SUB-ASSY, SSBC FULLY DRESSED CONTROL PANEL
999000288 DBA, MARS $1/5 BILL ACCEPTOR MODEL AE2481D5E (FOR IT CASH VAULT ONLY)
925000297D DEDICATED, US BOWLER’S CLUB 2009
845265297 DVD UPGRADE, INSTRUCTIONS SSB TO SSBC09
765265297 DVD UPGRADE, SSBC2009 DVD DISK
840500288R SILVERSTRIKE.COM CARD
900297001R I/O BOARD FOR US SSBC 2009 KIT, W/ MODEM
900297002R I/O BOARD FOR US SSBC 2009 DEDICATED, W/ MODEM
925000297 KIT - US SSBC 2009
925000297CP KIT - US SSBC 2009 W/CONTROL PANEL
815000297 MANUAL, SSBC 2009
820000297 MARQUEE, SSBC 2009
850000001R PUSHBUTTON ASSY, RED WITH VERTICAL MOUNTED SWITCH
850000003R PUSHBUTTON ASSY, WHITE WITH VERTICAL MOUNTED SWITCH
840000288 QUICK INSTALL GUIDE, BOWLER'S CLUB
903265297 RETRO-ONLINE UPGRADE FOR SSB KIT TO SSBC 09
903265297D RETRO-ONLINE UPGRADE FOR SSB DEDICATED TO SSBC 09
830000288R SIDE DECAL, BOWLER'S CLUB
900000297 SYSTEM BOX, SSBC 2009
880000030R TRACKBALL ASSY, 3" WHITE
885000030 TRACKBALL PLATE FOR 3" TRACKBL WITH STANDOFFS
Silver Strike Bowler’s Club™ Version 10/09 Page 60
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
APPENDIX D
NIGHTHAWK COMPONENT DIAGRAMS
Nighthawk System Box Diagram
Video and I/O Dip Switch Settings
Silver Strike Bowler’s Club™ Version 10/09 Page 61
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
I/O Board Diagram for KITS
This I/O Board accepts a JAMMA connector.
Note: Some elements are not available on I/O boards for Offline Kits.
I/O Board Diagram for DEDICATED CABINETS
Note: Some elements are not available on I/O boards for Offline Kits.
Silver Strike Bowler’s Club™ Version 10/09 Page 62
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Detailed Cable Connection Diagram for KITS
(Main)
(Optional)
Silver Strike Bowler’s Club™ Version 10/09 Page 63
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Detailed Cable Connection Diagram for DEDICATED CABINETS
Silver Strike Bowler’s Club™ Version 10/09 Page 64
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
BLACK/RED
GREEN/YELLOW
WHITE/RED
FLORESENT
LAMP POWER
110VAC
FLORESENT
LAMP
FROM I/O PCB
1
2
3
LEFT SPEAKER + (YELLOW/RED)
GREEN/YELLOW
LEFT SPEAKER - (YELLOW/GREEN)
.093 3PIN PLUG
LEFT
SPEAKER
SOFT POWER (BLUE/WHITE)
SOFT POWER (WHITE/BLUE)
RIGHT SPEAKER + (WHITE/RED)
GREEN/YELLOW
RIGHT SPEAKER - (WHITE/GREEN)
RIGHT
SPEAKER
1
2
3
.093 3PIN PLUG
FROM I/O PCB
DC POWER CABLE
SOUND CABLE
WHITE RCA JACK
RED RCA JACK
PLUG AC FEMALE
NIGHTHAWK SYSTEM
BOX
USB USB
15 PIN VGA
USB CABLE
CID PCB
J1
USB
.093 2PIN RECEPTACLE
1
2
GND (BLACK)
+12V (YELLOW)
1
2
3
1
2
3
+5V (RED)
GND (BLACK)
+12V (YELLOW)
.093 3PIN PLUG .093 3PIN RECEPTACLE
TO SPEAKERS
3
2
1
RIGHT SPEAKER - (WHITE/GREEN)
GREEN/YELLOW
RIGHT SPEAKER + (WHITE/RED)
.093 3PIN RECEPTACLE
3
2
1
LEFT SPEAKER - (YELLOW/GREEN)
GREEN/YELLOW
LEFT SPEAKER + (YELLOW/RED)
.093 3PIN RECEPTACLE
SOUND CABLE
USB USB
15 PIN VGA
OSD PCB
UNDER CONTROL PANEL
MONITOR POWER
110VAC
BLACK/RED
GREEN/YELLOW
WHITE/RED
LEFT
SW-PB SW-PB
OVERHEAD
SW-PB
CONTROL PANEL
GREEN/YELLOW
RIGHT
+5V
LAMP
.093 6PIN PLUG
TRACKBALL
COIN MECH 1
SW SPST
GREEN
VAULT
FLAT SCREEN VGA
MONITOR
TRACKBALL
TEST
SW-PB
SW-PB
VOLUME DOWN
15 PIN VGA
VGA CABLE
CHASSIS POWER
110VAC
PLUG AC MALE
BLACK WHITE
VGA CABLE
VGA CABLE
.100 13PIN IDC
CONTROL PANEL
9
10
11
12
13
6
7
4
5
8
1
2
3
USB CABLE
LAMP (RED/GREEN)
LAMP (RED/YELLOW)
6
5
4
3
2
1
8
7
U209 PIN 9
U209 PIN 6
U209 PIN 5
U209 PIN 4
U209 PIN 3
U209 PIN 2
U209 PIN 7
3
4
1
2
5
BALL WEIGHT
SW-PB
SW-PB
VOLUME UP
SERVICE PANEL
PLUG AC MALE
WHITE
CDROM USB
USB CABLE
UNDER CONTROL PANEL
110VAC
COIN
METER
CDROM POWER
GREEN
START
SW-PB
CARD READER
SW-PB
SOFT POWER
GND (BLACK)
OVERHEAD (VIOLET/WHITE)
RIGHT (YELLOW/WHITE)
LEFT (BROWN/WHITE)
BALL WEIGHT (BLACK/WHITE)
(BLUE/WHITE)
LAMP (RED/YELLOW)
(GREEN/WHITE)
LAMP (RED/GREEN)
START (RED/WHITE)
SOFT POWER (WHITE/YELLOW)
SOFT POWER (WHITE/ORANGE)
LAMP POWER (RED/BLACK)
6
7
8
9
10
11
12
13
3
4
5
1
2
.100 13PIN IDC
CONTROL PANEL
AC HOT (BLACK/RED)
AC NEUTRAL (WHITE/RED)
BILL (GREY/WHITE)
BILL GND (BLACK)
COIN 1 (RED/BLUE)
COIN GND (BLACK)
LAMP GND (BLACK)
LAMP POWER (RED/BLACK)
TEST GND (BLACK)
TEST (BLUE)
VOL GND (BLACK)
VOL DOWN (ORANGE/YELLOW)
VOL UP (ORANGE/WHITE)
METER POWER (RED)
COIN METER (BLACK)
USB CABLE
DBA
.093 9PIN PLUG
GREEN
LAMP POWER (RED/BLACK)
GND (BLACK)
START (RED/WHITE)
HELP (BLUE/WHITE)
BALL WEIGHT (BLACK/WHITE)
VOL GND (BLACK)
OVERHEAD (VIOLETWHITE)
RIGHT (YELLOW/WHITE)
LEFT (BROWN/WHITE)
OPTIONS (GREEN/WHITE)
8
7
6
10
9
5
4
3
2
1
J103
USB
3
4
1
2
+12V (YELLOW)
GND (BLACK)
+5V (RED)
GND (BLACK)
USB CABLE
DBA POWER
110VAC
BLACK/RED
GREEN/YELLOW
WHITE/RED
1
2
3
.093 3PIN PLUG
BILL (GREY/WHITE)
BILL GND (BLACK)
TEST VOLUME
.062 3PIN RECEPTACLE
.062 4PIN RECEPTACLE
TEST GND (BLACK)
TEST (BLUE)
SERVICE (N/C)
VOL DOWN (ORANGE/YELLOW)
VOL UP (ORANGE/WHITE)
COIN METER (RED/GREEN))
METER POWER (RED/BLACK)
7
6
5
4
3
2
1
COIN METER
.062 2PIN RECEPTACLE
COINS
3
4
5
1
2
8
9
6
7
.093 9PIN PLUG
3
4
5
1
2
8
9
6
7
COIN 4 (GREY/BROWN)
LAMP GND (BLACK)
LAMP POWER (RED/BLACK)
COIN 3 (GREY/ORANGE)
COIN 2 (GREEN/BLUE)
COIN 1 (RED/BLUE)
BILL (GREY/WHITE)
BILL GND (BLACK)
COIN GND (BLACK)
.093 9PIN RECEPTACLE
HOT (BLACK)
PLUG AC MALE
J205
U210 PIN 7
U210 PIN 6
U210 PIN 8
U210 PIN 9
Q206 COLLECTOR
DEDICATED I/O PCB
11PIN MINI KK
COINS
J208
6PIN MINI KK
TRACKBALL
ANTENNA
.093 6PIN RECEPTACLE
TRACKBALL
AC
LINE FILTER
HOT (BLACK)
CIRCUIT BREAKER
HOT (BLACK/ORANGE)
NEUTRAL (WHITE)
MODEM COAXIAL CABLE
EARTH GROUND
GREEN/YELLOW
GREEN/YELLOW
GREEN/YELLOW
GREEN/YELLOW
GREEN/YELLOW
GREEN/YELLOW
BLACK/RED
.062 2PIN PLUG
COIN METER
.062 4PIN PLUG
VOLUME
.062 3PIN PLUG
TEST
NEUTRAL (WHITE)
110VAC
POWER IN
GREEN/YELLOW
AC HOT
6PIN COMMONING CONNECTOR
BLACK
BLACK
BLACK/RED
1
3
5
2
4
6
BLACK/RED
BLACK/RED
BLACK/RED
AC NEUTRAL
SW DPDT
6PIN COMMONING CONNECTOR
WHITE
WHITE
WHITE/RED
1
3
5
2
4
6
WHITE
WHITE/RED
WHITE/RED
WHITE/RED
Silver Strike Bowler’s Club™ Version 10/09 Page 66
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
BLACK/RED
GREEN/YELLOW
WHITE
FLORESENT
LAMP POWER
110VAC
OSD PCB
LEFT
SPEAKER
GREEN
.093 3PIN PLUG
BLACK
1
GREEN
2
WHITE
3
.093 3PIN PLUG
MONITOR POWER
110VAC
LEFT
SW-PB
1
2
3
SW-PB
OVERHEAD
SW-PB
CONTROL PANEL
FLORESENT
LAMP
SW-PB
SOFT POWER
RIGHT
LOW/MEDIUM/TRI-MODE
MONITOR
10 PIN HEADER
VIDEO
RED
1
3 PIN HEADER
BLUE
GREEN
WHITE/BLACK
2
3
4
110VAC
BLACK
1
GREEN
2
WHITE
3
WHITE
8
9
5
6
7
10
GREEN
6 PIN RECEPTACLE
TRACKBALL
TRACKBALL
BALL WEIGHT
SW-PB
RIGHT
SPEAKER
GREEN
.156 10PIN KK CONNECTOR
8
9
10
5
6
7
1
2
3
4
SOFT POWER (WHITE/YELLOW)
SOFT POWER (WHITE/ORANGE)
LEFT SPEAKER + (YELLOW/RED)
LEFT SPEAKER - (YELLOW/GREEN)
RIGHT SPEAKER + (WHITE/RED)
RIGHT SPEAKER - (WHITE/GREEN)
SW-PB
1
2
3
4
5
6
.093 6PIN PLUG
FROM I/O PCB
DC POWER CABLE
SOUND CABLE
VIDEO
.093 6PIN PLUG
RED
BLUE
GREEN
WHITE/BLACK
WHITE
5
6
3
4
1
2
5
6
3
4
1
2
PLUG AC MALE
BLACK
CHASSIS POWER
110VAC
.093 6PIN RECEPTACLE
WHITE
GREEN
START/OPTIONS
OVERHEAD (VIOLET/WHITE)
RIGHT (YELLOW/WHITE)
LEFT (BROWN/WHITE)
BACK WEIGHT (BLACK/WHITE)
START (RED/WHITE)
GND (BLACK)
WHITE RCA JACK
RED RCA JACK
PLUG AC FEMALE
+5V (RED)
GND (BLACK)
GREEN
.093 9PIN PLUG
.093 9PIN RECEPTACLE
NIGHTHAWK SYSTEM
BOX
15 PIN VGA
USB CABLE
CID PCB
J1
USB
GND (BLACK)
+12V (YELLOW)
1
2
BOOSTER POWER
.093 2PIN RECEPTACLE
+5V (RED)
+5V (RED)
GND (BLACK)
GND (BLACK)
GND (BLACK)
+12V (YELLOW)
8
9
6
7
3
4
1
2
5
8
9
6
7
3
4
1
2
5
+5V (RED)
+5V (RED)
GND (BLACK)
GND (BLACK)
GND (BLACK)
+12V (YELLOW)
.093 9PIN PLUG .093 9PIN RECEPTACLE
POWER FOR COIN LAMPS
USB USB
SOUND CABLE
+12V (YELLOW)
GND (BLACK)
GND (BLACK)
+5V (RED)
1
2
3
4
1
2
3
4
+12V (YELLOW)
GND (BLACK)
GND (BLACK)
+5V (RED)
4 PIN HARD DRIVE
POWER PLUG
4 PIN HARD DRIVE
POWER RECEPTACLE
VGA CABLE
USB USB
VGA CABLE
15 PIN VGA
USB CABLE
OPTIONS LAMP (RED/GREEN)
HELP LAMP (RED/YELLOW)
6
5
4
3
2
1
8
7
.093 6PIN RECEPTACLE
GREEN
LAMP POWER (RED/BLACK)
TO SPEAKERS
LEFT SPEAKER + (YELLOW-RED)
LEFT SPEAKER - (YELLOW-GREEN)
RIGHT SPEAKER + (WHITE/RED)
RIGHT SPEAKER - (WHITE/GREEN)
U303 PIN 1
U303 PIN 2
U303 PIN 15
U303 PIN 14
RED (RED-BLACK)
GREEN (GREEN-BLACK)
BLUE (BLUE-BLACK)
GND (WHITE-BLACK)
COMPOSITE SYNC (WHITE)
FLY BY (VIOLET-WHITE)
RIGHT (YELLOW-WHITE)
LEFT (BROWN-WHITE)
BACK WEIGHT (BLACK/WHITE)
HELP (BLUE/WHITE)
OPTIONS (GREEN/WHITE)
START (RED-WHITE)
J204 PIN 23
J204 PIN 24
J204 PIN 25
J204 PIN 27
U204 PIN 6
U209 PIN 4
U209 PIN 3
U209 PIN 2
U209 PIN 5
U209 PIN 9
GND (BLACK)
BILL (GRAY-WHITE)
COIN 2 (GREEN-RED)
COIN 1 (RED-BLUE)
VOLUME UP (ORANGE-WHITE)
SERVICE (ORANGE-BLACK)
VOLUME DOWN (ORANGE-YELLOW)
TEST (BLUE)
COIN METER (RED-GREEN)
+5V (RED)
GND (BLACK)
GREEN
JAMMA
HARNESS
U210 PIN 2
U210 PIN 4
U210 PIN 3
U210 PIN 8
U210 PIN 6
U210 PIN 9
U210 PIN 7
Q206 COLLECTOR
8
7
6
5
4
3
2
1
10
9
U209 PIN 6
U209 PIN 7
KIT I/O PCB
J208
6PIN MINI KK
TRACKBALL
15 PIN VGA
J103
USB
1
2
3
+5V(RED)
GND(BLACK)
+12V(YELLOW)
3
4
1
2
.093 3PIN RECEPTACLE
+12V (YELLOW)
GND (BLACK)
+5V (RED)
GND (BLACK)
VGA CABLE
LOW/MEDIUM
RESOLUTION ONLY
USB CABLE
ANTENNA
GREEN
.093 9PIN RECEPTACLE MODEM COAXIAL CABLE
.093 3PIN PLUG
110VAC
1
2
3
BLACK
GREEN
WHITE
+5V
LAMP
COIN MECH 1
+5V
LAMP
COIN MECH 2
SERVICE
SW-PB
TEST
SW-PB
BILL (GRAY/WHITE)
COIN 1 (RED/BLUE)
COIN2 (GREEN/RED)
+5V (RED)
GND (BLACK)
VOL UP (ORANGE/WHITE)
SERVICE (ORANGE/BLACK)
VOL DOWN (ORANGE/YELLOW)
TEST (BLUE)
.093 2PIN RECEPTACLE
1
2
1
2
.093 2PIN PLUG
+5V (RED)
COIN METER (RED-GREEN)
USB CABLE
.093 9PIN PLUG
TRACKBALL
.093 6PIN RECEPTACLE
DELTA LINE FILTER
MODEL # 10VBAG5
BLACK
GREEN
WHITE
LITTLEFUSE
MODEL# 354
5 AMP
GREEN
SW SPST SW SPST
SW-PB
VOLUME UP
SW-PB
VOLUME DOWN
SERVICE PANEL
COIN
METER
HOT (BLACK)
PLUG AC MALE
NEUTRAL (WHITE)
110VAC
POWER
SW DPDT
110VAC X 4
1
2
3
BLACK
GREEN
WHITE
.093 3PIN RECEPTACLE
CARD READER
Silver Strike Bowler’s Club™ Version 10/09 Page 68
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
APPENDIX E
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The "Program", below, refers to any such program or work, and a "work based on the Program" means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term
"modification".) Each licensee is addressed as "you".
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the
Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program
(independent of having been made by running the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License. c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty
(or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this
License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of
Sections 1 and 2 above provided that you also do one of the following: a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and
2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of
Sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with
Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not
Silver Strike Bowler’s Club™ Version 10/09 Page 69
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded.
In such case, this License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free
Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the
Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE; THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER
PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY
OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER
PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.
To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found.
One line to give the program's name and an idea of what it does.
Copyright (C) yyyy name of author
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the
Free Software Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation,
Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
Copyright 2004 Incredible Technologies, Inc. (IT). Certain programs, identified at IT's Website are free software subject to an associated license.
1. Because certain programs are licensed free of charge, see it's website, there is no warranty for such programs to the extent permitted by applicable law. Except when otherwise stated in writing the copyright holders and/or other parties provide those programs "as is" without warranty of any kind, either expressed or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. The entire risk as to the quality and performance of those programs is with you. Should the programs prove defective, you assume the cost of all necessary servicing, repair or correction.
2. In no event unless required by applicable law or agreed to in writing will any copyright holder, or any other party who may modify and/or redistribute those programs be liable to you for damages including any general, special, incidental or consequential damages arising out of the use or inability to use those programs (including but not limited to loss of data or data being rendered inaccurate or losses sustained by you or third parties or a failure of those programs to operate with any other programs), even if such holder or other party has been advised of the possibility of such damages.
A complete machine-readable copy of the source code of those programs and associated license is available to any third party, at the it website.
Silver Strike Bowler’s Club™ Version 10/09 Page 70
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
APPENDIX F
INFORMATIONAL GUIDES
WIRELESS SIGNAL STRENGTH AND ANTENNA GUIDE
Understanding the basics of wireless antennas and the wireless frequency can help to improve your game’s signal strength and reliability.
In a perfect world the tower antenna and the machine’s antenna are in perfect phase with one another, and close enough in proximity that the strength is very good. In the real world the environment will change the phase of the signal and reduce its strength. Buildings, walls, metal or concrete, and even cars outside can affect the wireless signal. Basically, everything between the tower and the game will have some sort of affect.
The Antenna in Silver Strike Bowler’s Club is designed to “see” the wireless signal equally from any direction.
However, because objects in the machine’s surroundings can affect the signal, the antenna may accept a better signal if it is positioned a few inches from where it originally was, or possibly even rotated 180 degrees. There is no exact science to finding the optimal signal, so some locations may require some testing to get the best possible results.
When testing the wireless signal strength, go to ITNet Settings/Communication Settings in the System Setup menus. Use tape or Velcro to temporarily position the antenna into a new location, and let it settle for at least 30 seconds. Note the antenna’s current position, and signal strength reading on the screen. Then try another location or orientation and note the results. The best location for the antenna can usually be found using this procedure. Once you find the optimal spot, affix the antenna using the supplied mounting bracket so it stays in place. Remember that fewer obstacles between the antenna and the tower is your goal, and often that means that height is not always better.
A signal reading of 20 is good as long as there are not large or noticeable shifts in the signal strength. A signal reading of 25 to 50 is very good. A great signal is anything above 50. Each location is different, and these characteristics can often change if the surroundings change. It is a very good idea to check the signal strength test with every collection, to see if you are continuing to get the optimal signal position.
An Antenna signal booster can easily be installed if good signal strength can’t be obtained. The Incredible
Technologies part number is 900100510, “Booster Kit for Antenna”. Call Technical Support for more information.
GENERAL SWEEPSTAKES INFORMATION
If your Silver Strike Bowler’s Club machine is equipped and eligible for online play, it may enable players to participate in sweepstakes which IT, at its sole discretion, may from time to time conduct. The Official Rules of the sweepstakes, if conducted, will determine who is eligible, what the prizes are, and how they will be awarded.
These rules will be automatically downloaded to the unit when a sweepstakes is in progress. The rules, and copies of claim forms, may be reviewed at the Silver Strike Bowling website at http://www.silverstrikebowling.com.
Please note that sweepstakes, if conducted, may or may not be available in your jurisdiction. The Official Rules will determine where the sweepstakes will and will not be conducted, but if your jurisdiction has state or local regulations concerning sweepstakes, they may create further exclusions or conditions on entry and the awarding of prizes. IT will make reasonable efforts to avoid offering entries to ineligible players via the unit, but the Official
Rules along with applicable law shall determine who is and is not eligible to participate.
For more information on sweepstakes, including current rules if a sweepstakes is underway, see the Silver Strike
Bowling website at http://www.silverstrikebowling.com. Questions from players should be directed to that website, which will also have contact information.”
Silver Strike Bowler’s Club™ Version 10/09 Page 71
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
COLLECTIONS GUIDE
Silver Strike Bowler’s Club is a revolutionary product that requires some special handling when making a collection. Follow these steps every time you make a collection to make sure your profits and payments are managed properly.
Step 1: Collect your Cash Box
Open the coin vault and collect the cash and bills. Count it carefully and note the total.
Step 2: Review the Collection Screen
Remember that there are various fees and charges associated with some Silver Strike Bowler’s Club features, so it is important to compare the total cash you collect to the Collection Screen in the game. Open the outer door of the cash vault and press the System Setup button to enter the System Setup Menus. Select Collections and
Earnings, and then Do Collection. The machine will attempt to contact ITNet for complete and updated data.
If an error occurs, back out of the collection menus and try the process again. If the machine is unable to contact
ITNet, an estimated collection will be presented. This estimate will be close to accurate, and should allow you to complete the collection. Any discrepancies will be reconciled once the machine is able to connect properly.
This process takes you to the main collection screen. You should familiarize yourself with this screen, and how the information is displayed. These figures will help you determine how much to give to the location.
Note the date range and number of days in operation. If used properly, these fields should match with your collection dates. They are also important for calculating some of the various monthly fees.
Review the Total Income and Total Fees columns to see how much money your machine made for this time period, and how much is owed for various fees for this time period.
Total Income includes income from Cash, Player Accounts, and various Promotional or Gift Cards. Note that games paid by anything other than cash will NOT be in your cashbox, and will instead be credited to you on your
ITNet statement. THIS MEANS THAT YOUR CASHBOX WILL NOT MATCH YOUR TOTAL INCOME. Select
More Details to view a breakdown of cash, player account, and gift card income.
To verify the Operator and Location portions, first divide Total Income by the correct split percentage to get the operator and location portions of income. Then divide Total Fees by its split percentage to get both portions of the fees. Then subtract each fee portion from the income portion to get the final operator and location portions.
Total Fees include ITNet fees, Communication fees, Software Update fees, Hardware Upgrade fees and Taxes.
Note that Software Update Fees and Hardware Update Fees are included for your convenience, to help you cover the costs of owning and operating your equipment. These two line items are NOT included on your monthly ITNet statement, but give you a great opportunity to split some of these costs with the location. The Balance column displays the Total Income minus the Total Fees, giving you a realistic total of income for this time period.
Step 3: Pay the Location
Operator Portion of Balance is the amount of the collection that you keep. Operator Owes Location is the amount of the collection that you pay your location. These amounts are determined by the split percentages set in the
Collection Settings menus. See the reverse side for details on reviewing and adjusting these settings. In some extreme cases, there may not be enough money in the cash box to cover the location portion. It is highly
recommended that you do your best to pay the location at the time of the collection, as any missing funds will be reconciled during the monthly ITNet billing.
Step 4: Reset the Collection Screen
It is highly recommended that you reset these audit screens after every collection. When you have finished reviewing the information, highlight Do Collection and Exit and press Start. This will set all of the fields in the Do
Collection screen to zero. Be sure to empty your cash box at the same time, so these screens will match the money at your next collection.
Silver Strike Bowler’s Club™ Version 10/09 Page 72
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
INCOME SPLIT GUIDE
Silver Strike Bowler’s Club is a revolutionary product that offers a variety of ways to pay for game play, including player accounts and gift cards. There are also some fees associated with the operation of Silver Strike Bowler’s
Club. The operator/location split on many of these income and fee settings can be individually adjusted, allowing you to fine tune your costs and maximize your profits.
To access the Collection Settings menus, open the outer door of the cash vault and press the System Setup button to enter the System Setup Menus. Select General Settings, then Operator Adjustables, then Collection
Settings. The four available categories are: Hardware Update Fee, Income Splits, Fee Splits, and Tax Settings.
Hardware Update Fee
This menu allows you to adjust the Hardware Update Fee. This fee is included for your convenience, as a method to have the location pay for part of your equipment. The default value is $0.00 per week. Use this menu to adjust this value up or down. The weekly amount will be calculated on a per day basis, and added in to the
Total Fees field on the Do Collection screen. Note that the Hardware Update Fee is included for your convenience, and is NOT included on your monthly ITNet statement.
Operator/Location Income Splits
Use this menu to fine-tune your splits for income generated from Cash, Player Account, ITNet Money Card, and Operator
Money Card payments. Since there may be times when you have to pay the location before you actually have the cash in hand, you may want to adjust the split in your favor to cover the waiting period. The default settings are displayed on the accompanying screen.
Operator/Location Fee Splits
Use this menu to determine how you wish to split the various fees associated with Silver Strike Bowler’s Club, including ITNet Fees, Communication Fees, Software
Update Fees and Hardware Update Fees. The location is benefitting from your game by increasing food and beverage sales and creating loyal patrons. Setting some of these splits in your favor will help you to cover your costs in a fair and equitable manner. The default settings are displayed on the accompanying screen.
Tax Settings
Many states require special taxes or license fees that affect your bottom line. Use this menu to account for these costs in your collection.
In these menus, you can set the Tax Rate percentage, the Tax Type, meaning what part of the collection is taxed and who pays for these taxes, and the Tax Split for how to share these fees with your location.
Incredible Technologies hopes that you will take advantage of these menus to maximize your earnings potential.
Silver Strike Bowler’s Club™ Version 10/09 Page 73
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
PLAYER ACCOUNTS GUIDE
Silver Strike Bowler’s Club offers players the revolutionary ability to pay for play using their Player Prize Account from Golden Tee LIVE. Golden Tee LIVE players who choose to Play for Prizes have the ability to win money instantly, which is then stored on a special Player Account tied to their name.
When a player with an active Player Account plays a Silver Strike Bowler’s Club game he will be given the option to pay for his game with his Player Account money. If he chooses to do so, that money will be instantly debited from his account.
When a player pays for his game using his Player Account, he is not putting cash directly into the coin box. This means that the game revenue in a normal collection cycle will typically exceed the actual cash in the game.
Therefore it is very important to familiarize yourself with the Silver Strike Bowler’s Club collection menus and procedures, and your monthly ITNet billing statement.
When the player uses this Player Account money to play more Silver Strike, ITNet credits the full amount to the appropriate operator. These credits will appear on your regular monthly ITNet statement, and will mean a lower
ITNet bill, or sometimes even a credit to your bank account!
You are encouraged to pay the location portion in full at each collection, to avoid additional accounting on your part. While there might be a delay before you get your money back from ITNet, it will simplify the process immensely if you can manage the location up front. The operator/location split percentage has been set in your favor at 70/30 for Player Account income, since you must wait for your portion. Use this as a selling tool to adjust the collection in your favor.
♦
♦
♦
♦
♦
♦
The Collection Menu on Silver Strike Bowler’s Club details the various income sources for your review. You are encouraged to spend some time with these screens so you understand where your revenue is being generated.
You should also log in regularly to your Operator Services account on itsgames.com, to check on the performance of your equipment and check to see if the cash in the cash box will be enough to cover the split with your location.
♦
Winners from Golden Tee LIVE are encouraged to reinvest their winnings back to Silver Strike Bowler’s
Club
Player Account Play must be collected and distributed by ITNet first
The Player Account default split percentage is factory set to the operator’s advantage
Use the Collection Screen to set aside the various game fees and determine the location split
Pay the location portion at the time of collection if at all possible
Each month ITNet will issue a credit to your bill for Player Account activity on your machines.
In some cases this additional revenue and resulting credit will cover or surpass your fees, in which case
ITNet will credit your bank account.
Silver Strike Bowler’s Club™ Version 10/09 Page 74
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
SILVER STRIKE BOWLER’S CLUB REVENUE GUIDE
Revenue Types –With SSBC, cash is now not your only source of income. You can’t just count up the cash, deduct the fees and split the rest. Players can now play games with cash as well as 4 other revenue types. The different types of revenue are:
• Cash
• Player Account
• IT Gift cards
• Operator gift cards
• Operator free cash
Cash – Is just that; coin and currency. This is the only revenue that will appear on your hard meter, since it is counting physical pulses from the coin mechs and bill validator.
Player Account – This is the revenue earned when a player pays for his games with their Golden Tee LIVE
Player Account money. Players can still request a check for their winnings on the IT website, but most are rolling it right back into your games.
IT Gift Cards – This is revenue earned when a player swipes his gift card to pay for a game. IT Gift cards are purchased through us directly and shipped either to the purchaser or the recipient of the gift. This is similar to a
Wal-Mart or Best Buy gift card.
Operator Gift Cards – These are cards you can purchase for the cost of the plastic. You request whatever denomination you want. We will print the cards with your logo and artwork. You can give these out for promotions or refunds. Players will only be able to use them on machines registered to your account.
Operator Free Cash – This is the dollar value of games played using Operator free cash. These are credits you can put on your game for free play. This is intended for use if you want to test a game or set up a certain dollar amount of free play for promotional purposes, such as an open house.
ACCOUNTING FOR THE VARIOUS REVENUE TYPES
Cash – The SSBC machines are factory set to give you 60% and the location 40% of the cash.
Player Account and IT Gift Card revenue - Since this is revenue to you, but you do not have the cash in hand at the point of collection, you will get your money on your ITNet billing statement as a credit in a column titled “Due from IT.” You’ll need to pay your location on collection day and wait to receive this revenue until your next statement, so you are basically fronting this revenue type to your locations. Because of this, the machines are factory set to give you 70% of this revenue and the location 30%. That extra 10% of the cash split that you’re taking will help cover the 30% you’re fronting.
Operator Gift Cards and Operator Free Cash – Operator gift cards and Operator free cash are a way to promote your SSBC without splitting this “Revenue” with your locations. This is accounted like non-revenue or free play. This revenue is set to give you 100% and the location 0%. Please note that any fees incurred from this revenue still apply.
Please note all the revenue and fee settings can be changed to whatever split percentage you want, for each type of revenue source.
Silver Strike Bowler’s Club™ Version 10/09 Page 75
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
SILVER STRIKE BOWLER’S CLUB FEES
Fee Types
The 4 different fee types are ITNet Fees, Communication fees, Software Update fees and Hardware Update fees.
ITNet fees – This is what is paid to IT for the administering the online features and national sweepstakes. For every 10-frame game played, the ITNet portion is $0.05. See the player cost schedule below that breaks out these fees.
Play
Choice
Single Game
Total
To Player
$1.00
Operator
Portion
$0.95
ITNet
Portion
$0.05
3-Game Series
Throwdown
Bowler’s Club Card
$2.50
$2.00
$2.00
$2.35
$1.90
$0.25
$0.15
$0.10
$1.75
Software Update fees – Down the road when you purchase new updates for your game this will give you the opportunity to split the cost of your new updates with your location. It is handled much like the Hardware Update fee, described below.
Hardware Update fee – This Hardware Update fee is for you and you alone. You will NEVER BE BILLED for this fee. Operators have been asking for a place where they could recoup extra costs (should they so desire) from their locations. The default weekly fee is $0.00 per week as soon as you turn the SSBC game on. Many operators use this feature for other purposes. It can be used in certain locations where a weekly minimum is required. It can also be used for a weekly contest participation fee. The dollar amount of this fee can be changed to whatever dollar amount you want. The percentage split may also be adjusted.
ACCOUNTING FOR FEES
All of the fees above are factory set to split 50/50. The collection will take the different revenue types and calculate the different percentage splits, then take the different fees and calculate their split percentages. The fees will be deducted from the revenue and a dollar value is given to you and to your location. These values are shown on the collection screens in System Setup mode.
COLLECTIONS
SSBC Collection Screen – The first thing you will see is the collection from and to dates. Just below that you will either see “Estimated Collection” or “Actual Collection.” If you see “Estimated Collection” there was a problem getting a connection to our servers. We strongly suggest you back out without collecting and then go right back in to try to connect again. Nine times out of ten you should get an actual reading.
In the gray boxes, you will see the line item “days of operation.” This is the number of days since your last collection screen was cleared. You will see the total income, total fees, balance, operator portion of balance and operator owes location numbers. Since cash is no longer your only source of revenue, it is very important to view the details of the total income. To get these numbers, simply move the trackball up to the “More Details” box located directly to the right of the total income dollar value. Click your start button and you will be into the revenue breakdown page.
This screen shows a line item for each type of revenue source. This is where you can compare your cash on screen to your cash in hand. You can then go back to the main collection screen and do the same for your total fees. When you are done viewing all your numbers, click on the “Do Collection and Exit” button. The game will then send the collection data to your secure operator services web page for viewing at your office.
The next page is a sample SSBC collection sheet, showing the different revenue and income. This also shows the default percentages of the various split settings. You may want to take this form with you to your collections until you are comfortable with the system.
Silver Strike Bowler’s Club™ Version 10/09 Page 76
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
COLLECTION WORKSHEET
Location ______________________ CID______________
From ___/____/_ ___ to ___/____/__ __
Collector _______________________ ____
Total Income $__________________
Cash ____________ (Default 60% Operator/40% Location)
Player Account (Due from IT) ____________ (Default 70%/30%)
____________ (Default 70%/30%) IT Gift Cards
Operator Free Cash
Operator Gift Cards
____________ (Default 100%/0%)
____________ (Default 100%/0%)
Total Fees $__________________
ITNet Fees ____________ ($0.05 p/ 10 frame game, $0.10 p/ Throwdown game)
Communication Fee ____________ ($0.36 per day; or $10 per month)
Hardware Update Fee ____________ (default is $0.00 per day)
Software Update Fees____________ (will activate with new update)
Net to Split $_____________/______________
Operator portion / Location Portion
Silver Strike Bowler’s Club™ Version 10/09 Page 77
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
SSBC COLLECTION PROCEDURE
Follow this step-by-step visual guide to aid in proper collections on your machines. Refer to the
Collections Guide in your manual for more helpful information.
Press the System Setup button inside the coin door to access the System menus.
Use the trackball to highlight Collections & Earnings and press the Start button.
From the Collections & Earnings Menu, highlight Do
Collection and press the Start Button. The game will connect with ITNet and gather the most current financial data.
Look at the Operator Owes Location line item. This is the location portion that should be paid at the time of the collection. This number will NOT match the cash in the coinbox, due to the various alternative payment options.
However, you should pay the location his share now. Any money owed to you will be credited to you on your monthly
ITNet statement.
Silver Strike Bowler’s Club™ Version 10/09 Page 78
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Once the location is paid, your collection is effectively complete. However, if you wish to view a more detailed breakdown of the various income and fee categories, use the trackball to highlight More Details and press the Start button.
The Collection Fees menu displays the various fees associated with the current collection.
Note that the Hardware Update Fee is included as a means for you to have the location help pay for the cost of the game, and IT does not collect or keep any portion of this fee. This fee is completely adjustable and can be set to zero if desired.
Silver Strike Bowler’s Club™ Version 10/09 Page 79
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
If you wish to view the operator and location portions of these various fee categories, highlight More Details and press the Start button.
This screen further details the operator and location portions for the various fees, based on the adjustable split settings. See the SSBC manual for more information on how to set up your splits.
To exit this menu, highlight Back and press the Start button.
To complete your collection, get back to the Do Collection menu. Once there, use the trackball to highlight Do
Collection & Exit, and press the Start button.
Silver Strike Bowler’s Club™ Version 10/09 Page 80
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Check the dates in the window to make sure they match your time period. To complete the collection, highlight Yes: Record
It and press the Start button.
This will reset all the income, fees and days in operation to zero, so your next collection will be accurate for that time period.
MENU NAVIGATION SHORTCUTS
Continue to select Back on the various screens until you get to the Main Menu. Highlight Exit and press the Start button to exit System Setup mode and return to the game.
Force a Call
• Push the red system setup button inside the coin door
• Select the ITNet Settings menu
• Select the Connection Tests menu
• Select Force Call to ITNet
• Exit all the way out when complete
Change Collection Settings
• Push the red System Setup button inside the coin door
• Select General Settings menu
• Select Operator Adjustables menu
• Select Collection Settings menu
• Select the menu that you want changed
Add Operator Free Cash
• Push the red System Setup button inside the coin door
• Select Collection and Earnings
• Select Add Free Cash
• Move the trackball left/right to select the desired dollar amount
Silver Strike Bowler’s Club™ Version 10/09 Page 81
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
GAME ICON DESCRIPTIONS
Cooling Icon
The cooling icon (pictured right) will appear in the game's attract mode to warn you that a fan is not operating at minimum recommended standards. If the fans do not operate at suggested levels it may cause your game to overheat and fail. Call Incredible
Technologies Technical Support at 847-870-7027 x121 for assistance.
Signal Strength Icon
There are two ways to check the signal strength of your Silver Strike Bowler’s Club test machine. First, you can power the game off and on. A signal meter will appear in the lower right corner of the game’s boot-up screen. The number of bars that are displayed indicate the signal strength. Additionally, you can enter Operator Mode by pressing the System
Setup button inside the coin vault door. Once at the main Operator Mode menu, use the trackball and Start button to select ITNet Settings, then Communication Settings to view more information.
Tickets Owed Icon
The tickets owed icon (pictured right) will appear in the game's attract mode to warn you that the ticket dispenser is not dispensing tickets. It then tells you how many tickets are owed to players.
Online/Offline Icon
This icon appears in the game’s attract mode when no one is playing, to alert players and owners of the status of the game’s connection to ITNet. If the icon shows an Offline status, the game either does not have a connection to ITNet or is not registered to ITNet.
Sweepstakes/No Prizes Icon
This icon appears in the game’s attract mode to identify the status of the online sweepstakes. If the icon shows a No Prizes status, the sweepstakes feature has been disabled.
Silver Strike Bowler’s Club™ Version 10/09 Page 82
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
APPENDIX G
®
ITNet
®
Operating Rules
The following Rules shall govern the use of the ITNet system operated by Incredible Technologies, Inc., (“IT”) for the benefit of owners of its products which can make use of it (“Operators.”) Usage of the ITNet system constitutes agreement with, and agreement to comply with, these Rules. These Rules may be changed by IT at any time. Any change shall govern all usage of ITNet subsequent to such change being published on IT’s web site or written notice of such change being provided to any given Operator, whichever comes first.
Forms: All Operators of TGAMES, as that term is used in the Operator Agreement must complete the
following forms and keep them up-to-date with IT.
♦
The ITNet Debit Account Form requests basic bank account information, since a portion of
the income generated by ITNet features is paid to Incredible Technologies, to be used for online features and administration. You can use your existing business account, or set up a separate account just for this purpose. Only one Debit form is required.
♦
The ITNet Operator Agreement outlines the basic commitments by both parties required to
support the ITNet system.
♦
The Game Registration Form asks for the location that your machine is in. A separate
Game Registration Form is required for each of your machines.
♦
An IRS Form W-9 so that we may appropriately report all payments made to your
company to the IRS as required by Federal law.
Timely Payment; Remedies: Operators of TGAMES shall timely pay all monies due IT in the normal
course of business. Operators of TGAMES agree that IT may sweep their bank accounts as set forth in relevant payment agreements between IT and Operators for monies due IT, including monies due for products and services purchased by an Operator and not paid for by separate check or wire transfer.
Operators of TGAMES further agree that IT shall have the right to limit the online access of, or disable, any TGAME owned by an Operator for which any payments, including but not limited to ITNet Fees or
Upgrade Payments, are not paid timely. IT shall promptly re-enable any TGAME so disabled upon the payment of all monies owed to IT by Operator. Operators of TGAMES further agree that they will pay reasonable collection costs and fees, including simple interest of One Percent (1%) per calendar month or fraction of a calendar month on all payments more than fifteen (15) days late.
Silver Strike Bowler’s Club™ Version 10/09 Page 83
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Operating Restrictions: Operators must obey the following rules and restrictions related to the
operation of TGAMES:
1. Operators must report non-compliance or cheating on ITNET Rules, either by other Operators or by players of TGAMES, should this become known to an Operator.
2. Operators shall only operate TGAMES at locations where OPERATOR has used its best, good-faith efforts to determine that the operation of TGAMES and related game play features are in compliance with all local, state, and other governmental body laws and regulations.
3. Operators shall make reasonable efforts to disable any user-adjustable feature which they know or should have known as not lawful to operate in the location where a TGAME is being operated.
4. Operators shall make reasonable efforts to properly license, certify, register, or otherwise comply with tracking, licensing and taxation requirements in the location where a TGAME is being operated.
Operators shall indemnify and hold IT harmless for incorrect or inadequate licensing, registration, or taxation procedures which result in a claim against IT.
5. Operators shall only operate TGAMES in a traditional coin-operated environment. TGAMES shall be operated in a commercially reasonable fashion at all times. Failure to operate TGAMES in a commercially reasonable fashion, or to locate them in a traditional coin-operated environment, as determined solely by IT, shall be cause for appropriate action, up to and including loss of the ability to connect any given TGAME or TGAMES to the ITNet, at IT’s sole discretion.
6. Operators agree that these Rules are subject to change at IT’s sole discretion. Any change posted on IT’s website and/or otherwise reasonably communicated to Operators shall be effective with regard to any particular TGAME upon the beginning of the next billing cycle for that TGAME.
Game Maintenance: All Operators of TGAMES shall maintain such games in a reasonable and
prudent manner, shall not materially alter them from the state in which they were sold by IT, and shall install and maintain all IT-supplied components as directed by IT in service manuals, service bulletins, and any other notification or instruction means. All Operators of TGAMES agree to indemnify and hold
IT harmless for any claim by any Operator, employee or agent of an Operator, or any third party in which the Operator’s installation or maintenance, or lack thereof, of a TGAME was a contributory factor in causing such claim. Operators shall also provide prompt and courteous technical support and service to locations where TGAMES have been placed in service.
Governing Law and Jurisdiction: The validity and construction of these Rules, and the Operator
Agreement which governs and empowers them, and of the rights and obligations herein shall be determined and governed by the laws of the State of Illinois. The parties hereby submit to the
Jurisdiction of any state or federal court in Cook County Illinois. Operators operating outside the borders of the United States of America, regardless of their citizenship or residency, explicitly agree to allow any assets they may have in the USA or any other foreign country to be attached, garnished, forfeited or otherwise reached by any legal act if, after due process of law, they are found to be liable to
IT for damages by reason of breach of these Rules.
Severability: If any provision of these Rules shall be held by a court of competent jurisdiction to be
illegal, invalid or unenforceable, the parties nevertheless agree that the court should endeavor to give effect to the parties' intentions as reflected in the provision, and the remaining provisions shall remain in full force and effect.
Silver Strike Bowler’s Club™ Version 10/09 Page 84
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
ITNET REGISTRATION FORMS
®
ITNET DEBIT ACCOUNT FORM
You MUST have this form on file at Incredible Technologies, Inc. or your games will not be activated for online play.
After processing of the ITNet® forms, a personalized Operator Identification Card will be mailed to you.
The Operator Identification Card allows you to immediately register your games on-site.
Billing Information for Automatic Debit Payments
Authorization Agreement for Pre-authorized Payments For participation in ITNet®
I (we) authorize Incredible Technologies, Inc., hereafter called COMPANY, to initiate debit entries to my (our) bank account indicated below. I (we) authorize the financial institution named below, hereafter called INSTITUTION, to credit the amount of such entries to my (our) account to correct any errors, and the Institution to deposit any such corrections to my (our) account. I have attached an unsigned and voided check for the account I wish to be debited from time to time and in varying amounts.
Please Print Clearly and Legibly to Insure Accuracy.
Company Name
Address
Checking Account
Bank Account Number
Savings Account
City, State, Zip
Company Contact
Bank Routing Number (VERY IMPORTANT)
Bank Name
( )
Phone Number
( )
Fax Number
( )
Bank Phone Number
To assist in verifying data, please attach an unsigned voided blank check from your account.
The authority is to remain in full force and effect until I (we) revoke the agreement in writing as hereafter provided. Any revocation is effective only after
COMPANY has received written notice from me (us) to terminate this agreement in such time and manner to afford a reasonable opportunity to act upon the notice. I (we) have the right to stop payment of a debit entry by notification to the Institution in such time and manner to afford a reasonable opportunity to act prior to charging the account. A copy of this authorization will be provided at your request.
Email Addresses
Incredible Technologies® can alert you to a variety of information through email.
Please fill in the name and email address of the parties responsible for the following areas:
Main
Main Contact Name Main Contact Email Address
Billing
Billing Contact Name
Technical
Technical Contact Name
Promotions
Promotions Contact Name
Billing Contact Email Address
Technical Contact Email Address
Promotions Contact Email Address
Authorized Signature Date
Signature MUST accompany this form.
Fill out this form completely and mail or fax to:
Incredible Technologies, Inc.
3333 N. Kennicott Ave. Arlington Heights, IL 60004
(847) 870-7027 Phone (847) 454-9156 ITNet Registration Fax
Allow up to 10 Business Days for Processing.
Silver Strike Bowler’s Club™ Version 10/09 Page 85
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Silver Strike Bowler’s Club™ Version 10/09 Page 86
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
ITNET GAME REGISTRATION FORM
USE THIS FORM ONLY IF YOU CANNOT REGISTER YOUR GAME ON-SITE.
For faster service, Use Your ITNet® Operator Identification Card and Register Your Game Right at the Location!
Company Name: Contact:
Address:
Phone: Date:
Fax: Email:
ITNet® Operator ID Number:
Debit Account On File:
Yes No If No, include ITS® Debit Account Form.
Game Type:
Golden Tee LIVE
Silver Strike Bowler's Club
Game ID Number/CID:
Location Name:
Location Address:
City/State: Zip Code:
Be sure the Zip Code is accurate.
Location Phone Number: (
)
To avoid excessive phone charges, please enter the phone number of the jack that the machine is connected to.
Preferred Call-In Time:
am pm
Please Select One of the Following:
Please
REGISTER this Game.
Please
UNREGISTER This Game.
This Game is in a
NEW LOCATION.
Old Location Name:
Authorized Signature Date
Signature MUST accompany this form.
Fill out this form completely and mail or fax to:
Incredible Technologies, Inc.
3333 N. Kennicott Ave. Arlington Heights, IL 60004
(847) 870-7027 Phone (847) 454-9156 ITNet Registration Fax
Allow up to 10 Business Days for Processing.
Silver Strike Bowler’s Club™ Version 10/09 Page 87
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
ITNet
OPERATOR AGREEMENT
IMPORTANT!!
THIS DOCUMENT MUST BE SIGNED AND ON FILE WITH INCREDIBLE TECHNOLOGIES FOR YOUR
GOLDEN TEE LIVE AND SILVER STRIKE BOWLER'S CLUB MACHINES TO RECEIVE ONLINE FEATURES
OR TO RECEIVE TECHNICAL SUPPORT FOR THEM.
This AGREEMENT is made and entered into this ______ day of ____________, 20__, by and between Incredible
Technologies, Inc. ("IT"), an Illinois corporation, whose address is 3333 North Kennicott Avenue, Arlington
Heights, Illinois, 60004, and, _______________________________________________ (“OPERATOR”), whose address is:
________________________________________________________________________________________.
________________________________________________________________________________________.
WHEREAS, IT is skilled in the design of hardware and software relating to coin-operated video games, and;
WHEREAS, OPERATOR is skilled in the operation and management of coin-operated video games and represents that it is in the business of operating and managing the same.
NOW THEREFORE, for and in consideration of the mutual promises herein and other valuable consideration, the parties agree as follows:
1. APPLICATION.
This Agreement shall apply to the operation of all games (“TGAMES”) that are capable of connecting to IT’s
Incredible Technologies Network (“ITNET”) that Operator elects to register with the ITNET for the purpose of obtaining additional services and/or enabling additional game play features. It shall also apply to the operation of all IT games owned and operated by OPERATOR which are not online (“UGAMES”) as set forth below.
2. IT OBLIGATIONS.
IT agrees to do the following:
A. Administer the ITNET and offer contests on a regular and periodic basis throughout the year, and allow
OPERATOR’S TGAMES to be included in such contests provided that OPERATOR has complied with all ITNET rules and regulations, which are subject to change at IT’s sole discretion without notice, and this Agreement;
B. Be responsible for payment and distribution of all IT sponsored contest prizes;
C. Provide technical support to technical representatives of OPERATOR in the installation and maintenance of
TGAMES, in their connection to the ITNET, and in the installation and maintenance of UGAMES as set forth in sales agreements and accompanying manuals and warranties;
D. Fax, mail, email or otherwise make available billing statements to OPERATOR at least 4 business days prior to the date of automatic debiting of amounts owed to IT for ITNET related fees;
E. Provide usual and customary accounting and related services for ITNET fees, prizes, IRS 1099 reporting, and the like;
F. Warrant TGAMES and UGAMES for 90 day replacement for defects in materials and workmanship;
G. Pay all money, if any, owed to OPERATOR timely when due, as determined by IT in its sole discretion;
H. Use its best reasonable efforts to positively promote the ITNET program.
3. OPERATOR OBLIGATIONS.
OPERATOR agrees to the following:
A. Operate all TGAMES ITNET and UGAMES according to the terms of this Agreement, including adherence to the terms and conditions of the ITNET for games connected to the ITNET;
B. Fill out and submit Game Initialization Forms, Game Registration Forms, Debit Account Forms, and such other forms as IT may require from time to time;
C. Comply with the rules and regulations of the ITNET, which are subject to change at IT’s sole discretion without notice, and report non-compliance or cheating on ITNET rules should this become known to OPERATOR;
D. Provide prompt and courteous technical support and service to locations where the TGAMES and UGAMES have been placed in service;
E. Pay all money owed to IT, including but not limited to any and all ITNET fees incurred on games registered to
Operator’s account, by depositing such amounts in the account that OPERATOR sets up under the Debit Account
Form prior to the date that the account will be automatically debited;
ITNet® Operator Agreement Page 1 of 3 Version 12/08
Silver Strike Bowler’s Club™ Version 10/09 Page 88
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
ITNet
OPERATOR AGREEMENT
F. Only operate TGAMES and/or UGAMES at locations where OPERATOR has used its best, good-faith efforts to determine that the operation of TGAMES and/or UGAMES and related game play features are in compliance with all local, state, and other governmental body laws and regulations;
G. Only operate TGAMES and/or UGAMES in a traditional coin-operated environment as determined solely by IT, unless otherwise approved by IT;
H. Hold IT harmless for any losses due to theft or machine setting tampering, and;
I. Use its best reasonable efforts to positively promote the ITNET program.
4. TIMELY PAYMENT; REMEDIES
OPERATOR agrees to timely pay all monies due IT in the normal course of business. OPERATOR agrees that IT may sweep OPERATOR’S bank accounts as set forth in relevant payment agreements between IT and
OPERATOR for monies due IT, including monies due for products and services purchased by OPERATOR and not paid for by separate check or wire transfer. OPERATOR further agrees that IT shall have the right to limit the online access of, or disable, any TGAME or UGAME owned by OPERATOR for which any payments, including but not limited to ITNet Fees or Upgrade Payments, are not paid timely. IT agrees to promptly re-enable any
TGAME or UGAME so disabled upon the payment of all monies owed to IT by OPERATOR. Operators of
TGAMES further agree that they will pay reasonable collection costs and fees, including simple interest of One
Percent (1%) per calendar month or fraction of a calendar month on all payments more than fifteen (15) days late.
5. TAXES.
OPERATOR agrees to pay all taxes, fees, and assessments of any kind which may be assessed by any governmental body on the fees generated by the TGAMES and UGAMES, including, but not limited to any gross receipts taxes. OPERATOR is not responsible for any income tax or related assessments that are directly attributable to the business of IT.
6. ASSIGNMENT.
Neither party to this Agreement may sell, assign, transfer, pledge, or encumber, with or without consideration, all or any part of their interest in this Agreement without first obtaining the written consent of the other party.
7. EXPIRATION AND TERMINATION.
This Agreement shall continue in force for a period of one year from the date hereof, and shall automatically renew for successive one-year periods upon the anniversary date, and annually thereafter, unless sooner terminated in writing. Notwithstanding the forgoing, either party may terminate this agreement immediately upon notice to the other party.
8. EFFECT OF TERMINATION.
No termination shall affect any right, liability, or obligation, which accrues prior to such termination. Additionally, termination shall not affect either party's obligations to the other which by the nature thereof are intended to survive any such termination, including, but not limited to, the obligations of maintaining confidentiality as well as the obligations for payment of any outstanding monies that may be owed by one party to another and related remedies.
9. CONFIDENTIALITY.
Each party agrees that the trade secrets, technological information, marketing plans, game play data, location and game revenue data, and any other confidential business information disclosed in the course of performance under this Agreement, including the terms of this Agreement, shall be held in strict confidence and not disclosed to anyone without the written consent of the other party. Notwithstanding the forgoing, OPERATOR may share such financial information relating to TGAMES and/or UGAMES as OPERATOR deems appropriate with the locations in which the TGAMES and/or UGAMES are operated, and IT may list or otherwise publish such non-financial information regarding OPERATOR and the locations at which the TGAMES and/or UGAMES are operated on its website(s). Furthermore, IT may disclose such information as is reasonably necessary to collect unpaid accounts to debt collection agencies and/or its legal representatives. This provision shall survive the termination or expiration of this agreement for a period of two years from the date thereof.
10. GOVERNING LAW AND JURISDICTION.
The validity and construction of this Agreement and of the rights and obligations herein shall be determined and governed by the laws of the State of Illinois. The parties hereby submit to the Jurisdiction of any state or federal court in Cook County Illinois. OPERATORS operating outside the borders of the United States of America, regardless of their citizenship or residency, explicitly agree to allow any assets they may have in the USA or any other foreign country to be attached, garnished, forfeited or otherwise reached by any legal act if, after due process of law, they are found to be liable to IT for damages by reason of breach of this Agreement.
ITNet® Operator Agreement Page 2 of 3 Version 12/08
Silver Strike Bowler’s Club™ Version 10/09 Page 89
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
ITNet
OPERATOR AGREEMENT
11. SEVERABILITY.
If any provision of this Agreement shall be held by a court of competent jurisdiction to be illegal, invalid or unenforceable, the parties nevertheless agree that the court should endeavor to give effect to the parties' intentions as reflected in the provision, and the remaining provisions shall remain in full force and effect.
12. HEADINGS.
The headings in this Agreement are inserted for convenience and reference only, and are not intended to be part of or to affect the meaning or interpretation of this Agreement.
13. ENTIRE AGREEMENT, MODIFICATION AND MERGER.
This Agreement, including the Exhibits attached hereto, if any, states the entire Agreement between the parties with respect to the subject matter hereof, and supersedes and cancels all previous agreements, negotiations, commitments and representations regarding the subject matter of hereof which may have previously been made between the parties, whether orally or in writing. This Agreement may not be modified or altered except by written instrument duly executed by both parties.
14. ADDITIONAL DOCUMENTS.
The parties shall execute any and all documents, agreements, contracts, or other writings, which may be necessary or appropriate to carry out the terms, spirit and intent of this Agreement.
15. COUNTERPARTS.
This Agreement may be executed in any number of counterparts, each of which will be deemed an original, but all of which together shall constitute one and the same instrument.
16. INDEPENDENT CONTRACTORS.
Each of the parties to this Agreement shall be deemed to have the status of independent contractors, and nothing contained herein shall be deemed or construed as creating a joint venture, partnership, agency, or employer/employee relationship between the parties.
In Witness Whereof, the parties hereto have duly executed this Agreement on the day and year first written above.
OPERATOR INCREDIBLE TECHNOLOGIES, INC.
By: ____________________________________ By: _______________________________
Its: ____________________________________
(Printed name and title)
Its: _______________________________
(Printed name and title)
IMPORTANT!!
THIS DOCUMENT MUST BE SIGNED AND ON FILE WITH INCREDIBLE TECHNOLOGIES
FOR YOUR GOLDEN TEE LIVE MACHINES TO RECEIVE ONLINE FEATURES. YOU MUST ALSO RETURN
ALL NECESSARY IRS FORMS BEFORE YOUR ACCOUNT CAN BE ENABLED AND ONLINE FEATURES
ACCESSED.
Fill out this form completely and mail or fax to:
Incredible Technologies, Inc.
3333 N. Kennicott Ave.
Arlington Heights, IL 60004
(847) 870-7027 Phone (847) 454-9156 ITNet Registration Fax
Allow up to 10 Business Days for Processing.
ITNet® Operator Agreement Page 3 of 3 Version 12/08
Silver Strike Bowler’s Club™ Version 10/09 Page 90
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
TLS, have you transmitted all R text files for this cycle update?
Date
13
I.R.S. SPECIFICATIONS
TO BE REMOVED BEFORE PRINTING
INSTRUCTIONS TO PRINTERS
FORM W-9, PAGE 1 of 4
MARGINS: TOP 13mm (
1
2
"), CENTER SIDES.
PRINTS: HEAD to HEAD
PAPER: WHITE WRITING, SUB. 20. INK: BLACK
FLAT SIZE: 216mm (8
1
2
")
3 279mm (11")
PERFORATE: (NONE)
DO NOT PRINT — DO NOT PRINT — DO NOT PRINT — DO NOT PRINT
Action
O.K. to print
Revised proofs requested
Date Signature
Form
W-9
(Rev. October 2007)
Request for Taxpayer
Identification Number and Certification
Department of the Treasury
Internal Revenue Service
Name (as shown on your income tax return)
Business name, if different from above
Give form to the requester. Do not send to the IRS.
Check appropriate box: Individual/Sole proprietor Corporation Partnership
Limited liability company. Enter the tax classification (D=disregarded entity, C=corporation, P=partnership)
Other (see instructions)
©
©
Address (number, street, and apt. or suite no.)
City, state, and ZIP code
Exempt payee
Requester’s name and address (optional)
Incredible Technologies, Inc.
3333 North Kennicott Avenue
Arlington Heights, IL 60004
List account number(s) here (optional)
Part I
Taxpayer Identification Number (TIN)
Enter your TIN in the appropriate box. The TIN provided must match the name given on Line 1 to avoid backup withholding. For individuals, this is your social security number (SSN). However, for a resident alien, sole proprietor, or disregarded entity, see the Part I instructions on page 3. For other entities, it is your employer identification number (EIN). If you do not have a number, see How to get a TIN on page 3.
Social security number or
Note. If the account is in more than one name, see the chart on page 4 for guidelines on whose number to enter.
Employer identification number
Part II Certification
Under penalties of perjury, I certify that:
1.
The number shown on this form is my correct taxpayer identification number (or I am waiting for a number to be issued to me), and
2.
I am not subject to backup withholding because: (a) I am exempt from backup withholding, or (b) I have not been notified by the Internal
Revenue Service (IRS) that I am subject to backup withholding as a result of a failure to report all interest or dividends, or (c) the IRS has notified me that I am no longer subject to backup withholding, and
3.
I am a U.S. citizen or other U.S. person (defined below).
Certification instructions. You must cross out item 2 above if you have been notified by the IRS that you are currently subject to backup withholding because you have failed to report all interest and dividends on your tax return. For real estate transactions, item 2 does not apply.
For mortgage interest paid, acquisition or abandonment of secured property, cancellation of debt, contributions to an individual retirement arrangement (IRA), and generally, payments other than interest and dividends, you are not required to sign the Certification, but you must provide your correct TIN. See the instructions on page 4.
Sign
Here
Signature of
U.S. person
©
Date
©
General Instructions
Section references are to the Internal Revenue Code unless otherwise noted.
Purpose of Form
Definition of a U.S. person. For federal tax purposes, you are considered a U.S. person if you are:
● An individual who is a U.S. citizen or U.S. resident alien,
● A partnership, corporation, company, or association created or organized in the United States or under the laws of the United
A person who is required to file an information return with the
IRS must obtain your correct taxpayer identification number (TIN) to report, for example, income paid to you, real estate transactions, mortgage interest you paid, acquisition or abandonment of secured property, cancellation of debt, or contributions you made to an IRA.
Use Form W-9 only if you are a U.S. person (including a resident alien), to provide your correct TIN to the person requesting it (the requester) and, when applicable, to:
1. Certify that the TIN you are giving is correct (or you are waiting for a number to be issued),
2. Certify that you are not subject to backup withholding, or
3. Claim exemption from backup withholding if you are a U.S.
States,
● An estate (other than a foreign estate), or
● A domestic trust (as defined in Regulations section
301.7701-7).
Special rules for partnerships. Partnerships that conduct a trade or business in the United States are generally required to pay a withholding tax on any foreign partners’ share of income from such business. Further, in certain cases where a Form W-9 has not been received, a partnership is required to presume that a partner is a foreign person, and pay the withholding tax.
Therefore, if you are a U.S. person that is a partner in a partnership conducting a trade or business in the United States, provide Form W-9 to the partnership to establish your U.S.
exempt payee. If applicable, you are also certifying that as a
U.S. person, your allocable share of any partnership income from a U.S. trade or business is not subject to the withholding tax on foreign partners’ share of effectively connected income.
Note. If a requester gives you a form other than Form W-9 to request your TIN, you must use the requester’s form if it is substantially similar to this Form W-9.
status and avoid withholding on your share of partnership income.
The person who gives Form W-9 to the partnership for purposes of establishing its U.S. status and avoiding withholding on its allocable share of net income from the partnership conducting a trade or business in the United States is in the following cases:
● The U.S. owner of a disregarded entity and not the entity,
Cat. No. 10231X Form
W-9
(Rev. 10-2007)
13
I.R.S. SPECIFICATIONS
TO BE REMOVED BEFORE PRINTING
INSTRUCTIONS TO PRINTERS
FORM W-9, PAGE 2 of 4
MARGINS: TOP 13 mm ( 1
2
"), CENTER SIDES.
PRINTS: HEAD to HEAD
PAPER: WHITE WRITING, SUB. 20.
FLAT SIZE: 216 mm (8
PERFORATE: (NONE)
1
2
")
3 279 mm (11")
INK: BLACK
DO NOT PRINT — DO NOT PRINT — DO NOT PRINT — DO NOT PRINT
Form W-9 (Rev. 10-2007)
● The U.S. grantor or other owner of a grantor trust and not the trust, and
● The U.S. trust (other than a grantor trust) and not the beneficiaries of the trust.
Foreign person. If you are a foreign person, do not use Form
W-9. Instead, use the appropriate Form W-8 (see Publication
515, Withholding of Tax on Nonresident Aliens and Foreign
Entities).
Nonresident alien who becomes a resident alien. Generally, only a nonresident alien individual may use the terms of a tax treaty to reduce or eliminate U.S. tax on certain types of income.
However, most tax treaties contain a provision known as a
“saving clause.” Exceptions specified in the saving clause may permit an exemption from tax to continue for certain types of income even after the payee has otherwise become a U.S.
resident alien for tax purposes.
If you are a U.S. resident alien who is relying on an exception contained in the saving clause of a tax treaty to claim an exemption from U.S. tax on certain types of income, you must attach a statement to Form W-9 that specifies the following five items:
1. The treaty country. Generally, this must be the same treaty under which you claimed exemption from tax as a nonresident alien.
2. The treaty article addressing the income.
3. The article number (or location) in the tax treaty that contains the saving clause and its exceptions.
4. The type and amount of income that qualifies for the exemption from tax.
5. Sufficient facts to justify the exemption from tax under the terms of the treaty article.
Example. Article 20 of the U.S.-China income tax treaty allows an exemption from tax for scholarship income received by a
Chinese student temporarily present in the United States. Under
U.S. law, this student will become a resident alien for tax purposes if his or her stay in the United States exceeds 5 calendar years. However, paragraph 2 of the first Protocol to the
U.S.-China treaty (dated April 30, 1984) allows the provisions of
Article 20 to continue to apply even after the Chinese student becomes a resident alien of the United States. A Chinese student who qualifies for this exception (under paragraph 2 of the first protocol) and is relying on this exception to claim an exemption from tax on his or her scholarship or fellowship income would attach to Form W-9 a statement that includes the information described above to support that exemption.
If you are a nonresident alien or a foreign entity not subject to backup withholding, give the requester the appropriate completed Form W-8.
What is backup withholding? Persons making certain payments to you must under certain conditions withhold and pay to the
IRS 28% of such payments. This is called “backup withholding.”
Payments that may be subject to backup withholding include interest, tax-exempt interest, dividends, broker and barter exchange transactions, rents, royalties, nonemployee pay, and certain payments from fishing boat operators. Real estate transactions are not subject to backup withholding.
You will not be subject to backup withholding on payments you receive if you give the requester your correct TIN, make the proper certifications, and report all your taxable interest and dividends on your tax return.
Payments you receive will be subject to backup withholding if:
1. You do not furnish your TIN to the requester,
2. You do not certify your TIN when required (see the Part II instructions on page 3 for details),
3. The IRS tells the requester that you furnished an incorrect
TIN,
Page
2
4. The IRS tells you that you are subject to backup withholding because you did not report all your interest and dividends on your tax return (for reportable interest and dividends only), or
5. You do not certify to the requester that you are not subject to backup withholding under 4 above (for reportable interest and dividend accounts opened after 1983 only).
Certain payees and payments are exempt from backup withholding. See the instructions below and the separate
Instructions for the Requester of Form W-9.
Also see Special rules for partnerships on page 1.
Penalties
Failure to furnish TIN. If you fail to furnish your correct TIN to a requester, you are subject to a penalty of $50 for each such failure unless your failure is due to reasonable cause and not to willful neglect.
Civil penalty for false information with respect to
withholding. If you make a false statement with no reasonable basis that results in no backup withholding, you are subject to a
$500 penalty.
Criminal penalty for falsifying information. Willfully falsifying certifications or affirmations may subject you to criminal penalties including fines and/or imprisonment.
Misuse of TINs. If the requester discloses or uses TINs in violation of federal law, the requester may be subject to civil and criminal penalties.
Specific Instructions
Name
If you are an individual, you must generally enter the name shown on your income tax return. However, if you have changed your last name, for instance, due to marriage without informing the Social Security Administration of the name change, enter your first name, the last name shown on your social security card, and your new last name.
If the account is in joint names, list first, and then circle, the name of the person or entity whose number you entered in Part I of the form.
Sole proprietor. Enter your individual name as shown on your income tax return on the “Name” line. You may enter your business, trade, or “doing business as (DBA)” name on the
“Business name” line.
Limited liability company (LLC). Check the “Limited liability company” box only and enter the appropriate code for the tax classification (“D” for disregarded entity, “C” for corporation, “P” for partnership) in the space provided.
For a single-member LLC (including a foreign LLC with a domestic owner) that is disregarded as an entity separate from its owner under Regulations section 301.7701-3, enter the owner’s name on the “Name” line. Enter the LLC’s name on the
“Business name” line.
For an LLC classified as a partnership or a corporation, enter the LLC’s name on the “Name” line and any business, trade, or
DBA name on the “Business name” line.
Other entities. Enter your business name as shown on required federal tax documents on the “Name” line. This name should match the name shown on the charter or other legal document creating the entity. You may enter any business, trade, or DBA name on the “Business name” line.
Note. You are requested to check the appropriate box for your status (individual/sole proprietor, corporation, etc.).
Exempt Payee
If you are exempt from backup withholding, enter your name as described above and check the appropriate box for your status, then check the “Exempt payee” box in the line following the business name, sign and date the form.
13
I.R.S. SPECIFICATIONS
TO BE REMOVED BEFORE PRINTING
INSTRUCTIONS TO PRINTERS
FORM W-9, PAGE 3 of 4
MARGINS: TOP 13 mm ( 1
2
"), CENTER SIDES.
PRINTS: HEAD to HEAD
PAPER: WHITE WRITING, SUB. 20.
FLAT SIZE: 216 mm (8
PERFORATE: (NONE)
1
2
")
3 279 mm (11")
INK: BLACK
DO NOT PRINT — DO NOT PRINT — DO NOT PRINT — DO NOT PRINT
Form W-9 (Rev. 10-2007)
Generally, individuals (including sole proprietors) are not exempt from backup withholding. Corporations are exempt from backup withholding for certain payments, such as interest and dividends.
Note. If you are exempt from backup withholding, you should still complete this form to avoid possible erroneous backup withholding.
The following payees are exempt from backup withholding:
1. An organization exempt from tax under section 501(a), any
IRA, or a custodial account under section 403(b)(7) if the account satisfies the requirements of section 401(f)(2),
2. The United States or any of its agencies or instrumentalities,
3. A state, the District of Columbia, a possession of the United
States, or any of their political subdivisions or instrumentalities,
4. A foreign government or any of its political subdivisions, agencies, or instrumentalities, or
5. An international organization or any of its agencies or instrumentalities.
Other payees that may be exempt from backup withholding include:
6. A corporation,
7. A foreign central bank of issue,
8. A dealer in securities or commodities required to register in the United States, the District of Columbia, or a possession of the United States,
9. A futures commission merchant registered with the
Commodity Futures Trading Commission,
10. A real estate investment trust,
11. An entity registered at all times during the tax year under the Investment Company Act of 1940,
12. A common trust fund operated by a bank under section
584(a),
13. A financial institution,
14. A middleman known in the investment community as a nominee or custodian, or
15. A trust exempt from tax under section 664 or described in section 4947.
The chart below shows types of payments that may be exempt from backup withholding. The chart applies to the exempt payees listed above, 1 through 15.
IF the payment is for . . .
THEN the payment is exempt
Interest and dividend payments
for . . .
All exempt payees except for 9
Broker transactions Exempt payees 1 through 13.
Also, a person registered under the Investment Advisers Act of
1940 who regularly acts as a broker
Exempt payees 1 through 5 Barter exchange transactions and patronage dividends
Payments over $600 required to be reported and direct
1 sales over $5,000
Generally, exempt payees
1 through 7
2
2
1
See Form 1099-MISC, Miscellaneous Income, and its instructions.
However, the following payments made to a corporation (including gross proceeds paid to an attorney under section 6045(f), even if the attorney is a corporation) and reportable on Form 1099-MISC are not exempt from backup withholding: medical and health care payments, attorneys’ fees, and payments for services paid by a federal executive agency.
Page
3
Part I. Taxpayer Identification
Number (TIN)
Enter your TIN in the appropriate box. If you are a resident alien and you do not have and are not eligible to get an SSN, your TIN is your IRS individual taxpayer identification number
(ITIN). Enter it in the social security number box. If you do not have an ITIN, see How to get a TIN below.
If you are a sole proprietor and you have an EIN, you may enter either your SSN or EIN. However, the IRS prefers that you use your SSN.
If you are a single-member LLC that is disregarded as an entity separate from its owner (see Limited liability company
(LLC) on page 2), enter the owner’s SSN (or EIN, if the owner has one). Do not enter the disregarded entity’s EIN. If the LLC is classified as a corporation or partnership, enter the entity’s EIN.
Note. See the chart on page 4 for further clarification of name and TIN combinations.
How to get a TIN. If you do not have a TIN, apply for one immediately. To apply for an SSN, get Form SS-5, Application for a Social Security Card, from your local Social Security
Administration office or get this form online at www.ssa.gov. You may also get this form by calling 1-800-772-1213. Use Form
W-7, Application for IRS Individual Taxpayer Identification
Number, to apply for an ITIN, or Form SS-4, Application for
Employer Identification Number, to apply for an EIN. You can apply for an EIN online by accessing the IRS website at
www.irs.gov/businesses and clicking on Employer Identification
Number (EIN) under Starting a Business. You can get Forms W-7 and SS-4 from the IRS by visiting www.irs.gov or by calling
1-800-TAX-FORM (1-800-829-3676).
If you are asked to complete Form W-9 but do not have a TIN, write “Applied For” in the space for the TIN, sign and date the form, and give it to the requester. For interest and dividend payments, and certain payments made with respect to readily tradable instruments, generally you will have 60 days to get a
TIN and give it to the requester before you are subject to backup withholding on payments. The 60-day rule does not apply to other types of payments. You will be subject to backup withholding on all such payments until you provide your TIN to the requester.
Note. Entering “Applied For” means that you have already applied for a TIN or that you intend to apply for one soon.
Caution: A disregarded domestic entity that has a foreign owner
must use the appropriate Form W-8.
Part II. Certification
To establish to the withholding agent that you are a U.S. person, or resident alien, sign Form W-9. You may be requested to sign by the withholding agent even if items 1, 4, and 5 below indicate otherwise.
For a joint account, only the person whose TIN is shown in
Part I should sign (when required). Exempt payees, see Exempt
Payee on page 2.
Signature requirements. Complete the certification as indicated in 1 through 5 below.
1. Interest, dividend, and barter exchange accounts opened before 1984 and broker accounts considered active
during 1983. You must give your correct TIN, but you do not have to sign the certification.
2. Interest, dividend, broker, and barter exchange
accounts opened after 1983 and broker accounts considered
inactive during 1983. You must sign the certification or backup withholding will apply. If you are subject to backup withholding and you are merely providing your correct TIN to the requester, you must cross out item 2 in the certification before signing the form.
13
I.R.S. SPECIFICATIONS
TO BE REMOVED BEFORE PRINTING
INSTRUCTIONS TO PRINTERS
FORM W-9, PAGE 4 of 4
MARGINS: TOP 13 mm ( 1
2
"), CENTER SIDES.
PRINTS: HEAD to HEAD
PAPER: WHITE WRITING, SUB. 20.
FLAT SIZE: 216 mm (8
PERFORATE: (NONE)
1
2
")
3 279 mm (11")
INK: BLACK
DO NOT PRINT — DO NOT PRINT — DO NOT PRINT — DO NOT PRINT
Form W-9 (Rev. 10-2007) Page
4
3. Real estate transactions. You must sign the certification.
You may cross out item 2 of the certification.
4. Other payments. You must give your correct TIN, but you do not have to sign the certification unless you have been notified that you have previously given an incorrect TIN. “Other payments” include payments made in the course of the requester’s trade or business for rents, royalties, goods (other than bills for merchandise), medical and health care services
(including payments to corporations), payments to a nonemployee for services, payments to certain fishing boat crew members and fishermen, and gross proceeds paid to attorneys
(including payments to corporations).
5. Mortgage interest paid by you, acquisition or abandonment of secured property, cancellation of debt, qualified tuition program payments (under section 529), IRA,
Coverdell ESA, Archer MSA or HSA contributions or
distributions, and pension distributions. You must give your correct TIN, but you do not have to sign the certification.
What Name and Number To Give the Requester
1.
2.
3.
For this type of account:
Individual
Two or more individuals (joint account)
Custodian account of a minor
(Uniform Gift to Minors Act)
Give name and SSN of:
The individual
The actual owner of the account or, if combined funds, the first
1 individual on the account
The minor
2
4.
The grantor-trustee
1
5.
6.
7.
8.
a. The usual revocable savings trust (grantor is also trustee) b. So-called trust account that is not a legal or valid trust under state law
Sole proprietorship or disregarded entity owned by an individual
For this type of account:
Disregarded entity not owned by an individual
A valid trust, estate, or pension trust
Corporate or LLC electing corporate status on Form 8832
The actual owner
1
The owner
3
Give name and EIN of:
The owner
Legal entity
4
The corporation
9.
10.
Association, club, religious, charitable, educational, or other tax-exempt organization
Partnership or multi-member LLC
The organization
The partnership
11.
A broker or registered nominee The broker or nominee
12.
Account with the Department of
Agriculture in the name of a public entity (such as a state or local government, school district, or
The public entity prison) that receives agricultural program payments
1
List first and circle the name of the person whose number you furnish. If only one person on a joint account has an SSN, that person’s number must be furnished.
2
Circle the minor’s name and furnish the minor’s SSN.
3
You must show your individual name and you may also enter your business or “DBA” name on the second name line. You may use either your SSN or EIN (if you have one), but the IRS encourages you to use your SSN.
4
List first and circle the name of the trust, estate, or pension trust. (Do not furnish the TIN of the personal representative or trustee unless the legal entity itself is not designated in the account title.) Also see Special rules for partnerships on page 1.
Note. If no name is circled when more than one name is listed, the number will be considered to be that of the first name listed.
Secure Your Tax Records from Identity Theft
Identity theft occurs when someone uses your personal information such as your name, social security number (SSN), or other identifying information, without your permission, to commit fraud or other crimes. An identity thief may use your SSN to get a job or may file a tax return using your SSN to receive a refund.
To reduce your risk:
● Protect your SSN,
● Ensure your employer is protecting your SSN, and
● Be careful when choosing a tax preparer.
Call the IRS at 1-800-829-1040 if you think your identity has been used inappropriately for tax purposes.
Victims of identity theft who are experiencing economic harm or a system problem, or are seeking help in resolving tax problems that have not been resolved through normal channels, may be eligible for Taxpayer Advocate Service (TAS) assistance.
You can reach TAS by calling the TAS toll-free case intake line at 1-877-777-4778 or TTY/TDD 1-800-829-4059.
Protect yourself from suspicious emails or phishing
schemes. Phishing is the creation and use of email and websites designed to mimic legitimate business emails and websites. The most common act is sending an email to a user falsely claiming to be an established legitimate enterprise in an attempt to scam the user into surrendering private information that will be used for identity theft.
The IRS does not initiate contacts with taxpayers via emails.
Also, the IRS does not request personal detailed information through email or ask taxpayers for the PIN numbers, passwords, or similar secret access information for their credit card, bank, or other financial accounts.
If you receive an unsolicited email claiming to be from the IRS, forward this message to [email protected]. You may also report misuse of the IRS name, logo, or other IRS personal property to the Treasury Inspector General for Tax Administration at
1-800-366-4484. You can forward suspicious emails to the
Federal Trade Commission at: [email protected] or contact them at
www.consumer.gov/idtheft or 1-877-IDTHEFT(438-4338).
Visit the IRS website at www.irs.gov to learn more about identity theft and how to reduce your risk.
Privacy Act Notice
Section 6109 of the Internal Revenue Code requires you to provide your correct TIN to persons who must file information returns with the IRS to report interest, dividends, and certain other income paid to you, mortgage interest you paid, the acquisition or abandonment of secured property, cancellation of debt, or contributions you made to an IRA, or Archer MSA or HSA. The IRS uses the numbers for identification purposes and to help verify the accuracy of your tax return.
The IRS may also provide this information to the Department of Justice for civil and criminal litigation, and to cities, states, the District of Columbia, and U.S.
possessions to carry out their tax laws. We may also disclose this information to other countries under a tax treaty, to federal and state agencies to enforce federal nontax criminal laws, or to federal law enforcement and intelligence agencies to combat terrorism.
You must provide your TIN whether or not you are required to file a tax return. Payers must generally withhold 28% of taxable interest, dividend, and certain other payments to a payee who does not give a TIN to a payer. Certain penalties may also apply.
APPENDIX H
MOUNTING TEMPLATES
TRACKBALL ORIENTATION DIAGRAM
Silver Strike Bowler’s Club™ Version 10/09 Page 95
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Silver Strike Bowler’s Club™ Version 10/09 Page 96
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
TRACKBALL MOUNTING TEMPLATE
Silver Strike Bowler’s Club™ Version 10/09 Page 97
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Silver Strike Bowler’s Club™ Version 10/09 Page 98
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
BUTTON TEMPLATES
Silver Strike Bowler’s Club™ Version 10/09 Page 99
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Silver Strike Bowler’s Club™ Version 10/09 Page 100
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
CARD READER MOUNTING TEMPLATE A
Silver Strike Bowler’s Club™ Version 10/09 Page 101
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
CARD READER MOUNTING TEMPLATE B
Silver Strike Bowler’s Club™ Version 10/09 Page 102
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
FAN HOLE TEMPLATE
Silver Strike Bowler’s Club™ Version 10/09 Page 103
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Silver Strike Bowler’s Club™ Version 10/09 Page 104
© Copyright 2006-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law.
All other marks are the properties of their respective owners. All rights reserved.
Contact Information
IT Sales and Service
To purchase additional Golden Tee machines or any of IT's other fine products please visit IT's website at www.itsgames.com and click on PRODUCTS!
General Numbers
IT Sales Hotline:
800-262-0323 x106
847-870-7027 x106
Technical Support, Warranty, & Repair:
Incredible Technologies, Inc.
800-262-0323 x121
847-870-7027 x121
847-454-9008 Fax
Parts, Customer Service, & Operator Services:
Incredible Technologies, Inc.
800-262-0323 x118
847-870-7027 x 118
847-870-0120 Fax
IT Mailing Address:
Incredible Technologies, Inc.
3333 North Kennicott Avenue
Arlington Heights, IL 60004-0129
ITNet Registration/Sales Fax Number
847-454-9156
General Fax Number 847-870-0120
Tech Services Fax Number 947-454-9008
IT Vendor Information
Mars Technical Service:
Phone: 800-345-8172
Happ Controls:
Phone: 888-289-4277
GOLDEN TEE® Unplugged, ITS®, INCREDIBLE TECHNOLOGIES®, IT®, ITNet®, and IT incredible TECHNOLOGIES® are the properties of Incredible Technologies, Inc.
All Rights Reserved.
© Copyright 2007-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law. All other marks are the properties of their respective owners. All rights reserved.
Incredible Technologies, Inc.
3333 N. Kennicott Ave.
Arlington Heights, IL 60004
Phone (847) 870-7027 (800) 262-0323
www.itsgames.com
GOLDEN TEE® Unplugged, ITS®, INCREDIBLE TECHNOLOGIES®, IT®, ITNet®, and IT incredible TECHNOLOGIES® are the properties of Incredible Technologies, Inc.
All Rights Reserved.
© Copyright 2007-2010 Incredible Technologies, Inc. All Rights Reserved. Unauthorized duplication is a violation of applicable law. All other marks are the properties of their respective owners. All rights reserved.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 TABLE OF CONTENTS
- 8 Update, Showpiece and Kit Contents
- 8 SSBC 07 to SSBC 09 DVD Update Contents
- 8 SSB to SSBC Upgrade Kit Contents
- 8 Showpiece Cabinet Contents
- 8 Complete Kit Contents
- 9 SSBC 2009 DVD Update Instructions
- 9 Updates Silver Strike Bowler's Club 2007 to SSBC 2009
- 10 SSBC 2009 DVD Update Instructions
- 10 Updates Silver Strike Bowler's Club 2007 to SSBC 2009
- 10 Marquee Installation
- 10 For Newer Dedicated Cabinets
- 10 For Older Dedicated Cabinets and Golden Tee Fore! Cabinets
- 11 DVD Upgrade Instructions
- 11 Original Silver Strike Bowling to Silver Strike Bowler's Club 2009
- 11 Part 1
- 11 Part 2
- 13 Marquee, GRAPHICS & Antenna Installation
- 13 For Newer Dedicated Cabinets
- 13 For Older Dedicated Cabinets and Golden Tee Fore! Cabinets
- 13 Install Side Decals
- 13 Install Antenna (Online Kit Only)
- 14 Antenna Adjustment
- 14 USB Card Reader Installation Instructions
- 14 Step 1A Remove Existing Card Reader (GT4 Cabinets)
- 14 OR
- 14 Step 1B Cut Hole for USB Card Reader (Other Cabinets)
- 14 Step 2 Install NEW USB Card Reader
- 15 Showpiece Cabinet
- 15 Leg Leveler Adjustment
- 15 Mount Main Screen Display
- 15 Install Marquee
- 16 DIP SWITCH SETTINGS and NIGHTHAWK SYSTEM BOX
- 16 DIP Switch Settings
- 17 Video Connections
- 17 DIP Switch Settings
- 17 Audio Connections
- 18 INSTALL SECONDARY MONITOR
- 18 If you plan to use Two TVs for your video outputs, follow the instructions below.
- 18 ABOUT THE SECONDARY MONITOR
- 19 Final Check
- 19 Apply Power
- 19 Check the Cabinet ID Device (CID) Number
- 19 Check the Coin Switch and Bill Validator
- 19 Checking the Wireless Connection Signal Strength (Online Only)
- 19 Cabinet Temperature
- 19 Custom Adjustments
- 20 General Cabinet Maintenance
- 20 Care and Cleaning of Rubber Bumper
- 20 Nighthawk Air Filter
- 20 Trackball Maintenance
- 20 Care and Cleaning of Cooling Fans and Vents
- 21 Showpiece Cabinet Repair Procedures
- 21 System Chassis Box
- 21 System Chassis Removal
- 21 System Chassis Installation
- 21 I/O Board
- 21 I/O Board Removal
- 21 I/O Board Installation
- 22 Cabinet Identification Device (CID)
- 22 CID Removal and Replacement
- 22 Cash Vault
- 22 Cash Vault Removal and Replacement
- 22 Locks
- 22 Volume and Service Buttons
- 23 Bill Acceptor
- 23 Bill Acceptor Removal
- 23 Bill Acceptor Installation
- 23 Stacker Removal
- 23 Coin Mech
- 23 Coin Mech Removal
- 23 Meter
- 23 Control Panel
- 23 Soft Power Switch
- 23 Trackball Replacement
- 24 Button Replacement
- 24 Control Panel Removal
- 24 Control Panel Graphics Removal
- 24 Control Panel Graphics Installation
- 24 Speakers
- 24 Speaker Access
- 25 Antenna (Online Only)
- 25 Card Reader (Online Only)
- 25 Card Reader Removal
- 25 Card Reader Installation
- 26 Complete Kit Installation
- 26 Recommended Tools
- 26 Installation Preparation
- 26 BEFORE YOU START…
- 27 Preparing The Cabinet
- 27 Cabinet Selection
- 27 Preparing the Cabinet for Installation
- 27 Check JAMMA Harness and Wiring
- 27 Check Coin Mechs and Bill Acceptor
- 27 Check Coin Door Connections
- 28 Check Monitor
- 28 Remove Cabinet Graphics
- 28 Remove Existing Card Reader (If applicable)
- 29 Cut Hole for Card Reader (Online Kit Only)
- 29 Vacuum Cabinet Thoroughly
- 30 Electronics Installation
- 30 Install Nighthawk System box
- 30 Install Cabinet Identification Device (CID)
- 31 Install I/O Board
- 31 Install Antenna (Online Kit Only)
- 31 Install Card Reader (Online Kit Only)
- 31 Install Ticket Dispenser (Optional)
- 32 Control Panel Installation
- 32 Install Optional Control Panel for Existing I.T. Cabinets
- 32 Trackball and Button Preparation (For Most Kits)
- 32 Trackball Preparation
- 33 Button Preparation
- 33 Control Panel Overlay Installation
- 34 Finishing The Control Panel
- 35 Complete System Box Connections
- 35 Attach I/O Power, Audio, and USB cables.
- 35 Attach Main Video Cable
- 35 Attach Power Cable
- 35 Soft Power / Fan Cable
- 36 Complete I/O Board Connections
- 36 Connect JAMMA Harness
- 36 Connect the Control Panel Switches and Cable
- 36 Connect Coin Door Lamps
- 36 Connect the Trackball
- 36 Connect Antenna
- 36 Connect Audio Cables
- 36 Connect the USB Cable
- 36 Connect Medium or Low Resolution Monitor
- 36 Connect VGA or SVGA Monitor
- 36 Connect I/O Power Cable
- 36 Check All Connections
- 37 Cabinet Graphics Installation
- 37 Side Decal Installation
- 37 Marquee Installation
- 38 Final Connections
- 38 Coin Doors, Test Switch, and Volume Controls
- 38 Initial Power-Up
- 39 SYSTEM SETUP MENUS
- 39 Navigating The Menu System
- 39 Entering System Setup Mode
- 39 Selecting a Menu
- 39 Choosing a Menu/Option
- 39 Changing a Value
- 39 Main Menu
- 39 Collections & Earnings
- 39 General Settings
- 39 Troubleshooting Shortcuts
- 39 Silver Strike Settings
- 40 ITNet Settings (online only)
- 40 Collections & Earnings Menu
- 40 Do Collection
- 40 Clear Unused Cash
- 40 Add Free Cash
- 40 Back
- 40 Do Collection
- 40 Collection Date Range
- 40 Days In Operation
- 40 Reset
- 40 Total Income
- 40 More Details
- 41 Total Fees
- 41 More Details
- 41 Balance
- 41 Operator Portion of Balance
- 41 Operator Owes Location
- 41 Back
- 41 Do Collection and Exit
- 41 General Settings
- 41 Operator Adjustables
- 41 System Tests
- 41 Advertisements
- 41 Back
- 42 Operator Adjustables
- 42 General Adjustments
- 42 Money Slot Adjustments
- 42 Sound Adjustments
- 42 Collection Settings
- 42 Reset To Factory Settings
- 42 Back
- 42 General Adjustments
- 42 Coin Message
- 42 Game Mode
- 42 2nd Monitor Mode
- 42 Reset Values
- 42 Back
- 43 Money Slot Adjustments
- 43 Money Slot 1 (all machines)
- 43 Money Slot 2 (kits only)
- 43 Money Slot 3
- 43 Reset Values
- 43 No
- 43 Yes
- 43 Back
- 43 Sound Adjustments
- 43 In Game Volume
- 43 Attract Volume
- 43 Attract Mode Sounds
- 43 Stereo/Mono
- 43 Reset Values
- 43 Back
- 44 Collection Settings
- 44 Set Hardware Update Fee
- 44 Operator/Location Income Splits
- 44 Cash
- 44 Player Account (online only)
- 44 ITNet Money Card (online only)
- 44 Operator Money Card (online only)
- 44 Operator/Location Fee Splits
- 44 ITNet Fees (online only)
- 44 Communication Fees (online only)
- 44 Software Update Fees (online only)
- 44 Hardware Update Fees
- 45 Tax Settings
- 45 Set Tax Rate
- 45 Set Tax Type
- 45 Set Tax Split
- 45 Reset to Defaults
- 45 Back
- 45 Reset to Factory Settings
- 46 System Tests
- 46 Video Tests
- 46 Sound Tests
- 46 Player Control Tests
- 46 Mechanical Meter Test
- 46 Hardware Tests
- 46 Back
- 46 Video Tests
- 46 Color Adjustments
- 46 Contrast Adjustments
- 46 Screen Size Adjustment
- 46 Back
- 47 Color Adjustments
- 47 Color Grid Adjustment
- 47 Red Screen
- 47 Green Screen
- 47 Blue Screen
- 47 Back
- 47 Contrast Adjustments
- 47 White Screen
- 47 50% White Screen
- 47 25% White Screen
- 47 Black Screen
- 47 Contrast Screen
- 47 Back
- 47 Screen Size Adjustment
- 48 Sound Tests
- 48 Stored Sound
- 48 Streaming Sound
- 48 Speaker Test
- 48 Back
- 48 Player Control Tests
- 48 Mechanical Meter Test
- 48 Click Meter
- 48 Back
- 49 Hardware Tests
- 49 Hardware/Software
- 49 Check Hard Drive
- 49 Check Cooling
- 49 Check Card Reader
- 49 Back
- 49 Hardware/Software
- 49 System Info
- 49 USB Info
- 49 Version Info
- 49 Back
- 49 System Info
- 49 USB Info
- 49 Version Info
- 50 Check Hard Drive
- 50 Check File Data
- 50 Check File System
- 50 Back
- 50 Check Cooling
- 50 Back
- 50 Check Card Reader (online only)
- 50 Back
- 51 Troubleshooting Shortcuts
- 51 Check Card Reader (online only)
- 51 Check Cooling
- 51 Check Hard Drive
- 51 Hardware & Software
- 51 Communications Settings (online only)
- 51 Player Control Tests
- 51 System Tests
- 51 Back
- 51 Silver Strike Settings
- 51 Player Cost Schedule
- 51 Game Audits
- 51 Game Options
- 51 Reset Leaderboards
- 51 Ticket Dispenser
- 51 Back
- 52 Player Cost Schedule
- 52 Single Play
- 52 Series Play
- 52 Throwdown
- 52 SSB Survivor
- 52 3-Frame Practice
- 52 3-Frame Buy In
- 52 View Fixed Costs
- 52 Player’s Card Purchase
- 52 Reset Defaults
- 52 Back
- 53 Game Audits
- 53 Coin Slot 1 (All Machines)
- 53 Coin Slot 2 (Kits only)
- 53 Bill Acceptor
- 53 Lifetime Money In
- 53 Bowlers Club Cards Purchased
- 53 Number of Tickets Paid
- 53 Ticket Value %age Payout
- 53 More
- 53 Reset Audits
- 54 Game Options
- 54 Vegas Bowling
- 54 Buy Player Cards
- 54 Sweepstakes
- 54 Announce Volume
- 54 Reset Values
- 54 More
- 54 Delay Timeout
- 54 Ball Timeout
- 54 3-Frame Practice
- 54 Survivor # Misses
- 54 Reset Values
- 55 Red pin Bonus Free Game
- 55 Reset # Games Awarded
- 55 Reset Values
- 55 Reset Leaderboards
- 55 Ticket Dispenser
- 56 ITNet Settings (Online Only)
- 56 Change Location/Register Game
- 56 Communication Settings
- 56 Connection Tests
- 56 Re-Activate Modem
- 56 Back
- 56 Change Location
- 57 Communication Settings
- 57 Configure Ethernet Settings
- 57 Back
- 57 Connection Tests
- 57 Check Latency Time
- 57 Force Call to ITNet
- 57 Back
- 57 Re-Activate Modem
- 58 SILVER STRIKE BOWLER’S CLUB TROUBLESHOOTING & REFERENCE
- 58 APPENDIX A Troubleshooting Guide
- 63 APPENDIX B JAMMA, Trackball, and I/O Power Connections
- 63 JAMMA Harness Connection
- 63 Trackball Harness Connector Pin Outs I/O Power Cable Pin Outs
- 64 APPENDIX C Replacement Part Numbers
- 65 APPENDIX D Nighthawk Component Diagrams
- 65 Nighthawk System Box Diagram
- 65 Video and I/O Dip Switch Settings
- 66 I/O Board Diagram for KITS
- 66 I/O Board Diagram for DEDICATED CABINETS
- 67 Detailed Cable Connection Diagram for KITS
- 68 Detailed Cable Connection Diagram for DEDICATED CABINETS
- 68 DEDICATED Cabinet Wiring Diagram
- 70 KIT Cabinet Wiring Diagram
- 73 APPENDIX E GNU General Public License
- 75 APPENDIX F Informational Guides
- 75 Wireless Signal Strength and Antenna Guide
- 75 General Sweepstakes Information
- 76 Collections Guide
- 76 Step 1: Collect your Cash Box
- 76 Step 2: Review the Collection Screen
- 76 Step 3: Pay the Location
- 76 Step 4: Reset the Collection Screen
- 77 Income Split Guide
- 77 Hardware Update Fee
- 77 Operator/Location Income Splits
- 77 Operator/Location Fee Splits
- 77 Use this menu to determine how you wish to split the various fees associated with Silver Strike Bowler’s Club, including ITNet Fees, Communication Fees, Software Update Fees and Hardware Update Fees. The location is benefitting from your game by incr...
- 77 Tax Settings
- 77 In these menus, you can set the Tax Rate percentage, the Tax Type, meaning what part of the collection is taxed and who pays for these taxes, and the Tax Split for how to share these fees with your location.
- 78 Player Accounts Guide
- 79 Silver Strike Bowler’s Club Revenue Guide
- 79 Accounting for the Various Revenue Types
- 80 Silver Strike Bowler’s Club Fees
- 80 Accounting for Fees
- 80 Collections
- 81 Collection Worksheet
- 82 SSBC Collection Procedure
- 85 Menu Navigation Shortcuts
- 85 Force a Call
- 85 Change Collection Settings
- 85 Add Operator Free Cash
- 86 Game Icon Descriptions
- 86 Cooling Icon
- 86 Signal Strength Icon
- 86 Tickets Owed Icon
- 86 Online/Offline Icon
- 86 Sweepstakes/No Prizes Icon
- 87 APPENDIX G
- 89 ITNet Registration Forms
- 89 ITNet DEBIT ACCOUNT FORM
- 89 Fill out this form completely and mail or fax to:
- 91 ITNet GAME REGISTRATION FORM
- 92 OPERATOR AGREEMENT
- 99 APPENDIX H Mounting Templates
- 99 Trackball Orientation Diagram
- 101 Trackball Mounting Template
- 103 Button Templates
- 105 Card Reader Mounting Template A
- 106 Card Reader Mounting Template B
- 106 Fan Hole Template