IBM T-117 Installation and Maintenance Manual

IBM 17″ 1 U Flat Panel Monitor Console Kit
Installation and Maintenance Guide
IBM 17″ 1 U Flat Panel Monitor Console Kit
Installation and Maintenance Guide
Note: Before using this information and the product it supports, read the general information in Appendix B, “IBM Statement of
Limited Warranty Z125-4753-07 11/2002,” on page 29 and the notices information in Appendix C, “Notices,” on page 47.
First Edition (March 2004)
© Copyright International Business Machines Corporation 2004. All rights reserved.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.
Contents
Safety
. . . . . . . . . . . . . . . v
Chapter 1. Introduction . . . . . . . . 1
Inventory checklist . . . . . . . . . .
Notices and statements used in this document .
.
.
. 1
. 3
Chapter 2. Installing the Flat Panel
Monitor Console Kit . . . . . . . . . 5
Installing the flat-panel monitor and keyboard tray . 5
Installing an optional console switch . . . . . . 14
Chapter 3. Hardware maintenance
information . . . . . . . . . . . . . 17
Customer-replaceable unit part numbers .
Replacing the cable-management arm .
Replacing the slide-rail assemblies . . .
Replacing the keyboard . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
17
19
21
25
Appendix A. Getting help and technical
assistance . . . . . . . . . . . . . 27
Before you call . . . . . . . .
Using the documentation . . . . .
Getting help and information from the
Web . . . . . . . . . . . .
Software service and support . . .
Hardware service and support . . .
© Copyright IBM Corp. 2004
. .
. .
World
. .
. .
. .
. .
. .
Wide
. .
. .
. .
. 27
. 27
. 27
. 28
. 28
Appendix B. IBM Statement of Limited
Warranty Z125-4753-07 11/2002 . . . . 29
Part 1 - General Terms . . . .
Part 2 - Country-unique Terms .
Part 3 - Warranty Information .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 29
. 32
. 43
Appendix C. Notices . . . . . . . . . 47
Edition notice . . . . . . . . . . . .
Trademarks . . . . . . . . . . . . .
Important notes . . . . . . . . . . . .
Electronic emission notices . . . . . . . .
Federal Communications Commission (FCC)
statement . . . . . . . . . . . . .
Industry Canada Class A emission compliance
statement . . . . . . . . . . . . .
Australia and New Zealand Class A statement
United Kingdom telecommunications safety
requirement . . . . . . . . . . . .
European Union EMC Directive conformance
statement . . . . . . . . . . . . .
Taiwanese Class A warning statement . . .
Chinese Class A warning statement . . . .
Japanese Voluntary Control Council for
Interference (VCCI) statement . . . . . .
.
.
.
.
47
48
48
48
. 48
. 49
. 49
. 49
. 49
. 50
. 50
. 50
Index . . . . . . . . . . . . . . . 51
iii
iv
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
Safety
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informações de Segurança.
Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí.
Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Avant d’installer ce produit, lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.
Antes de instalar este produto, leia as Informações sobre Segurança.
© Copyright IBM Corp. 2004
v
Antes de instalar este producto, lea la información de seguridad.
Läs säkerhetsinformationen innan du installerar den här produkten.
Important:
All caution and danger statements in this documentation begin with a
number. This number is used to cross reference an English caution or
danger statement with translated versions of the caution or danger
statement in the IBM NetBAY Rack Safety Information book.
For example, if a caution statement begins with a number 1,
translations for that caution statement appear in the IBM NetBAY Rack
Safety Information book under statement 1.
Be sure to read all caution and danger statements in this
documentation before performing the instructions. Read any additional
safety information that comes with your server or optional device
before you install the device.
vi
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
Statement 4:
DANGER
Electrical current from power, telephone, and communication cables is
hazardous.
To avoid a shock hazard:
v Do not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical storm.
v Connect all power cords to a properly wired and grounded electrical outlet.
v Connect to properly wired outlets any equipment that will be attached to
this product.
v When possible, use one hand only to connect or disconnect signal cables.
v Never turn on any equipment when there is evidence of fire, water, or
structural damage.
v Disconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless
instructed otherwise in the installation and configuration procedures.
v Connect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached devices.
To Connect:
To Disconnect:
1. Turn everything OFF.
1. Turn everything OFF.
2. First, attach all cables to devices.
2. First, remove power cords from outlet.
3. Attach signal cables to connectors.
3. Remove signal cables from connectors.
4. Attach power cords to outlet.
4. Remove all cables from devices.
5. Turn device ON.
Safety
vii
viii
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
Chapter 1. Introduction
The IBM® 17″ 1 U Flat Panel Monitor Console Kit is a flat-panel monitor and
keyboard tray in one solution. An optional IBM PS/2® Travel Keyboard with
UltraNav fits inside the front of the keyboard tray. The monitor and keyboard tray
occupy 1 U1 of space in a rack cabinet. You can install a console switch behind the
tray to attach more than one server to the flat-panel monitor and keyboard.
Inventory checklist
Note: The illustrations in this documentation might differ slightly from your
hardware.
The IBM 17″ 1 U Flat Panel Monitor Console Kit comes with the following items:
v One keyboard tray with built-in flat-panel monitor
v Two outer rails
v One rail-alignment spacer
1. Racks are measured in vertical increments of 1.75 inches each. Each increment is called a “U”. A 1-U-high device is 1.75 inches
tall.
© Copyright IBM Corp. 2004
1
v One left-side console-switch mounting bracket (for routing video, keyboard, and
mouse cables)
v One right-side console-switch mounting bracket
v One 2.4-m (8-ft) IEC connector power cable
v
v
v
v
Miscellaneous hardware kit (cage nuts, clip nuts, screws, cable straps)
Monitor documentation
IBM NetBAY Rack Safety Information book
This documentation
pa
ac
ks
el
se
+
\
|
D
P
au
nt
E
{
-
]
_
c
11
S
F
hi
ft
/
?
C
<
A
lt
,
H
M
Y
6
.
K
J
7
U
7
F
6
F
5
N
G
5
T
F
4
B
F
4
R
F
3
V
D
3
E
F
C
X
F
n
C
tr
S
l
hi
ft
C
ap
A
s
lt
Lo
Ta
b
ck
Z
`
A
~
1
Q
F
1
S
2
W
F
2
sc
E
tr
l
>
I
8
F
8
L
;
O
9
F
9
:
‘
S
“
P
0
F
10
[
P
rt
er
}
=
Lk
12
S
F
cr
B
et
e
In
E
se
rt
nd
ce
H
P
om
e
gD
n
P
gU
p
The IBM 17″ 1 U Flat Panel Monitor Console Kit is also available with a U.S. or
Japan thin keyboard. The following additional items come with these models:
v One thin keyboard with built-in pointing device
2
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
v One 1.8-m (6-ft) power cord
v One CD containing keyboard and mouse device drivers and keyboard
documentation
You might need the following tools to install the IBM 17″ 1 U Flat Panel Monitor
Console Kit:
v One utility knife or scissors
v One number 1 Philips screwdriver
v One number 2 Philips screwdriver
v One 7/16-inch wrench
v One 1/4-inch wrench
v One cage-nut-insertion tool or flat-blade screwdriver (for installing cage nuts in
some rack cabinets)
See the documentation that comes with your rack cabinet or console switch for
further information about those products.
Notices and statements used in this document
The caution and danger statements that appear in this document are also in the
multilingual IBM NetBAY Rack Safety Information document. Each statement is
numbered for reference to the corresponding statement in the Safety Information
document.
The following notices and statements are used in the documentation:
v Notes: These notices provide important tips, guidance, or advice.
v Important: These notices provide information or advice that might help you
avoid inconvenient or problem situations.
v Attention: These notices indicate potential damage to programs, devices, or data.
An attention notice is placed just before the instruction or situation in which
damage could occur.
v Caution: These statements indicate situations that can be potentially hazardous
to you. A caution statement is placed just before the description of a potentially
hazardous procedure step or situation.
v Danger: These statements indicate situations that can be potentially lethal or
extremely hazardous to you. A danger statement is placed just before the
description of a potentially lethal or extremely hazardous procedure step or
situation.
Chapter 1. Introduction
3
4
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
Chapter 2. Installing the Flat Panel Monitor Console Kit
The Flat Panel Monitor Console Kit occupies 1 U of mounting space in a rack
cabinet. If you have a NetBAY25, NetBAY42, NetBAY42 Enterprise, NetBAY22 with
Rack Extension Kit, Netfinity® 9306 Model 900 with Rack Extension Kit, or similar
rack cabinet, you can use the brackets that come with this kit to install an optional
console switch in the same 1 U of space.
Installing the flat-panel monitor and keyboard tray
Removing rack doors and side panels might make installation easier.
Use cage nuts for rack cabinets with square holes; use clip nuts for rack cabinets
with round holes. If your rack cabinet requires cage nuts, use a cage-nut-insertion
tool or a flat-blade screwdriver to install them.
Cage
nuts
Cage
nuts
Clip
nuts
See the documentation that comes with your rack cabinet for additional
information.
© Copyright IBM Corp. 2004
5
Statement 4:
DANGER
Electrical current from power, telephone, and communication cables is
hazardous.
To avoid a shock hazard:
v Do not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical storm.
v Connect all power cords to a properly wired and grounded electrical outlet.
v Connect to properly wired outlets any equipment that will be attached to
this product.
v When possible, use one hand only to connect or disconnect signal cables.
v Never turn on any equipment when there is evidence of fire, water, or
structural damage.
v Disconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless
instructed otherwise in the installation and configuration procedures.
v Connect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached devices.
To Connect:
1.
2.
3.
4.
5.
Turn everything OFF.
First, attach all cables to devices.
Attach signal cables to connectors.
Attach power cords to outlet.
Turn device ON.
To Disconnect:
1.
2.
3.
4.
Turn everything OFF.
First, remove power cords from outlet.
Remove signal cables from connectors.
Remove all cables from devices.
Complete the following steps to install the flat-panel monitor and keyboard tray
kit in a rack cabinet:
1. Place the tray on a stable flat surface.
Attention: The video cable is connected to the flat-panel monitor. As you
install the tray in the rack cabinet, be careful that you do not pinch or cut the
video cable.
2. If your tray has a thin keyboard installed, go to step 7 on page 8.
6
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
3. Remove the two back rubber pads from the bottom of the new keyboard and
discard them. (The rubber pads have an adhesive backing and can be peeled
from the surface.) If you leave the rubber pads on the keyboard, they will
extend into the 1-U space below.
Remove rubber pads
(two places)
Keyboard foot
Attention: Do not extend the keyboard feet. The flat-panel monitor screen
might be damaged if the feet are extended when the monitor is closed.
4. Carefully lift the front of the flat-panel monitor and raise the monitor to the
full upright position.
Thumbscrews
Chapter 2. Installing the Flat Panel Monitor Console Kit
7
pa
ac
ks
B
|
nte
r
}
=
]
E
{
-
hif
“
?
/
C
lt
A
H
M
,
J
<
.
K
U
7
F
7
6
Y
6
F
5
G
N
T
F
5
4
B
F
4
R
F
3
D
V
E
F
3
2
sc
C
X
l
F
n
C
tr
S
hif
t
C
ap
A
s
lt
Lo
Ta
b
ck
Z
`
A
~
1
Q
F
1
S
2
W
F
E
tr
l
>
I
8
F
8
L
;
O
9
F
9
:
‘
S
P
0
F
10
t
[
P
F
rtS
c
11
_
S
F
cr
Lk
12
+
\
P
au
D
se
ele
te
In
E
se
rt
nd
5. Carefully set the keyboard into the tray; then, route the keyboard-and-mouse
cable through the cord clip on the bottom, up through the opening on the
right side of the tray, and toward the cable-management arm. Pull the full
length of the cable through the opening.
Keyboard-and-mouse
cable routing
6. Secure the keyboard-and-mouse cable to the cable-management arm using the
existing cable straps.
7. Select a 1-U location in the rack for the flat-panel monitor and keyboard tray.
Use the following illustration to guide you as you install either cage nuts or
clip nuts on the rack. Use the cage nuts or clip nuts from the miscellaneous
hardware kit.
Note: If you are planning to install an optional console switch, make sure that
you install a cage nut or clip nut in the center-rear position shown
shaded in the following illustration.
U
U
U
U
U
U
U
U
U
U
U
U
Front
Rear
Optional console-switch nut
8
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
8. Loosen the two rail-adjustment screws on each of the outer slide rails; then,
extend the rails to their maximum outward adjustment.
Rail-adjustment
screws
9. Adjust the outer slide-rail brackets to fit the depth of the rack cabinet; then,
attach the front of the slide-rail brackets to the rack cabinet using four screws
from the miscellaneous hardware kit. Make sure that the slide-rail brackets
extend outside of the rack-cabinet mounting flanges.
Note: Do not install screws in the slide-rail bracket middle holes. These holes
are for the thumbscrews on the front of the tray.
Chapter 2. Installing the Flat Panel Monitor Console Kit
9
10. Loosely attach the back of the slide-rail brackets to the rack cabinet using four
screws from the miscellaneous hardware kit. Make sure that the slide-rail
brackets extend outside of the rack-cabinet mounting flanges.
Note: Do not install screws in the slide-rail bracket middle holes. These holes
are for the optional console-switch mounting brackets.
11. Tighten the two rail-adjustment screws on each of the outer rails that you
loosened in step 8 on page 9.
12. Loosen the front four slide-rail bracket screws; then, insert the rail-alignment
spacer into the slide-rail middle holes. The rail-alignment spacer must wrap
around the rails to align them correctly. Tighten the front four screws; then,
remove the spacer.
Note: Do not tighten the four rear slide-rail bracket screws at this time.
Rail-alignment spacer
10
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
13. Extend the inner part of the outer rails; then, slide the ball-bearing assemblies
forward to the front of the outer rails. Carefully slide the flat-panel monitor
and keyboard tray into the ball-bearing assemblies in the rails.
14. Press the release latches; then, push the flat-panel monitor and keyboard tray
completely into the rack. There will be resistance initially as the ball-bearing
assemblies align between the inner and outer rails. Pull the tray out halfway;
then, push it back in to seat the tray in the rails. Do this a few times until the
tray moves smoothly in the rails.
Release latch
15. Push the tray in the rack; then, tighten the four rear slide-rail bracket screws.
Chapter 2. Installing the Flat Panel Monitor Console Kit
11
16. Remove the rail-adjustment screw closest to the back of the rack from the
outer slide-rail bracket. Attach the cable-management arm to the outer
slide-rail bracket using this screw.
17. Connect the video, keyboard, and mouse connectors to either a server or a
console switch in the rack cabinet. Connect the power cord to the short
jumper cord on the cable-management arm; then, connect the power cord to a
properly grounded electrical outlet or power distribution unit (PDU).
18. Fully extend the tray from the front of the rack cabinet; then, neatly route
cables within the rack cabinet and secure them with cable straps along the
way.
12
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
19. See the flat-panel monitor documentation that comes with this kit for
information about operating the monitor. See the keyboard documentation for
information about operating the keyboard.
Note: When the monitor and keyboard are not in use, if the rack cabinet is in a
vibration-prone area, or during cabinet relocation, tighten the two
thumbscrews on the front of the tray to secure the tray inside the rack
cabinet.
Thumbscrew
If you are installing an optional console switch, continue to “Installing an optional
console switch” on page 14.
Chapter 2. Installing the Flat Panel Monitor Console Kit
13
Installing an optional console switch
You can use a console switch to attach more than one server to a single monitor
and keyboard. The console-switch option is available separately, but custom
mounting brackets for the switch come with this kit. You can use the brackets and
instructions that come with the console switch for other installation options.
By installing the console switch behind the Flat Panel Monitor Console Kit you can
store the console switch in the same 1-U space as the flat-panel monitor and
keyboard tray. Use the brackets that come with this kit to install the console switch
behind the tray.
Attention: The console switch will extend beyond the rear rack-cabinet mounting
flanges when you install the switch behind the tray. You must have a NetBAY25,
NetBAY42, NetBAY42 Enterprise, NetBAY22 with Rack Extension Kit, Netfinity
9306 Model 900 with Rack Extension Kit, or similar rack cabinet.
Complete the following steps to install a console switch behind the tray:
1. Attach the left-side bracket to the left side of the console switch using two 8-32
screws; then, attach the right-side bracket to the right side of the console
switch.
Note: The left-side bracket has a channel for you to route the power, video,
and keyboard-and-mouse cables. Make sure that you attach the brackets
to the console switch so that the channel on the left-side bracket faces
upward.
Console switch
8
7
6
5
4
3
2
1
A
Right-side bracket
Left-side bracket
14
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
2. Install the console switch behind the flat-panel monitor and keyboard tray
using two screws from the miscellaneous hardware kit.
Console
switch screw
8
7
5
3
6
4
2
1
A
Console
switch
screw
2
1
A
3. Route the power, video, and keyboard-and-mouse cables through the channel
in the left-side bracket on the console switch; then, connect the video,
keyboard, and mouse connectors to the console switch.
4. See the documentation that comes with the console switch for information
about connecting the flat-panel monitor, thin keyboard, and servers to the
console switch.
Chapter 2. Installing the Flat Panel Monitor Console Kit
15
16
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
Chapter 3. Hardware maintenance information
This chapter contains information about IBM customer-replaceable units (CRUs) for
the IBM 17″ 1 U Flat Panel Monitor Console Kit and instructions for replacement
parts that are not installed during a typical installation.
Customer-replaceable unit part numbers
IBM CRU part numbers are subject to change without notice. This section contains
a listing of the CRU part numbers that are available as of the date of this printing.
\
In
se
rt
D
ele
H
om
te
e
E
nd
P
gU
p
P
gD
B
ac
n
ks
pa
ce
|
+
]
E
nte
r
}
=
“
S
hif
t
P
?
/
.
C
tr
A
lt
H
M
,
J
<
F
7
7
F
6
Y
6
F
5
G
N
T
5
F
4
F
B
R
4
F
3
D
V
E
3
X
Q
Z
A
lt
Lo
ck
l
C
tr
F
n
S
hif
t
C
ap
s
Ta
b
`
A
~
1
F
1
S
C
F
2
2
W
E
sc
U
K
l
>
I
8
F
8
L
;
F
9
9
O
:
‘
0
F
10
[
{
-
P
rt
S
c
F
11
_
S
crL
k
F
12
P
au
se
Cable-management arm
Keyboard
Monitor/keyboard
tray
Outer slide rails
Inner slide rails
CRU part number
Description
23K4885
IBM 17″ 1 U Flat Panel Console Kit, without keyboard
23K4887
Slide rails (inner and outer rails, slide alignment spacer)
23K4889
Cable-management arm
89P8500
IBM PS/2 Travel Keyboard with UltraNav, U.S. keyboard
© Copyright IBM Corp. 2004
17
18
CRU part number
Description
89P8514
IBM PS/2 Travel Keyboard with UltraNav, Japan keyboard
26K4103
Miscellaneous hardware kit (left and right console-switch brackets,
cage nuts, clip nuts, screws, cable straps, keyboard cord clip)
6952300
One power cord connecting the power supply to ac power
36L8886
One power cord connecting the power supply to a power distribution
unit (PDU)
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
Replacing the cable-management arm
If you installed a console switch in the rear of the rack cabinet, it might be easier
to replace the cable-management arm if you remove the console switch first.
Complete the following steps to replace the cable-management arm:
1. Turn off the monitor; then, disconnect power from the monitor.
2. Disconnect the keyboard, mouse, and video connectors from the server or
console switch.
3. Remove the screw that attaches the cable-management arm to the outer
slide-rail bracket.
4. Fully extend the monitor and keyboard tray; then, temporarily remove the
keyboard-and-mouse, video, and power cables from the cable-management
arm.
Chapter 3. Hardware maintenance information
19
5. Remove the nut that attaches the cable-management arm to the tray; then,
attach the new cable-management arm to the tray using the same nut.
6. Route the video, power, and keyboard-and-mouse cables along the new
cable-management arm and secure them along the way with cable straps.
7. Attach the cable-management arm to the outer slide-rail bracket using the
same screw that you removed in step 3 on page 19.
8. If you removed a console switch from behind the tray, reinstall it now.
9. Reconnect the keyboard, mouse, and video connectors to the server or console
switch.
10. Connect power to the monitor.
20
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
Replacing the slide-rail assemblies
Complete the following steps to replace the outer and inner slide-rail assemblies
for the monitor and keyboard tray:
1. Turn off the monitor; then, disconnect power from the monitor.
2. Disconnect the keyboard, video, and mouse connectors from the server or
console switch.
3. If you installed a console switch in the rear of the rack cabinet, remove the
console switch from the rack.
4. Remove the screw that attaches the cable-management arm to the outer
slide-rail bracket.
5. Fully extend the monitor and keyboard tray from the front of the rack cabinet;
then, push in the release latch on each side of the tray and slide the monitor
Chapter 3. Hardware maintenance information
21
and keyboard tray assembly out of the rack
Release latch
6. Remove the eight screws that attach the outer slide rails to the rack cabinet;
then, remove the old outer slide rails from the cabinet.
7. Loosen the four rail-adjustment screws on both of the new outer slide-rail
brackets; then, extend the brackets to their maximum outward adjustment.
Rail-adjustment
screws
22
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
8. Adjust the outer slide-rail brackets to fit the depth of the rack cabinet; then,
attach the front of the slide-rail brackets to the rack cabinet using four screws.
Make sure that the slide-rail brackets extend outside of the rack-cabinet
mounting flanges.
Note: Do not install screws in the slide-rail bracket middle holes. These holes
are for the thumbscrews on the front of the tray.
9. Loosely attach the back of the slide-rail brackets to the rack cabinet using four
screws. Make sure that the slide-rail brackets extend outside of the
rack-cabinet mounting flanges.
Note: Do not install screws in the slide-rail bracket middle holes. These holes
are for the optional console-switch mounting brackets.
Chapter 3. Hardware maintenance information
23
10. Tighten the two rail-adjustment screws on each of the outer rails that you
loosened in step 7 on page 22.
11. Loosen the front four slide-rail bracket screws; then, insert the rail-alignment
spacer into the slide-rail middle holes. The rail-alignment spacer must wrap
around the rails to align them correctly. Tighten the front four screws; then,
remove the spacer.
Note: Do not tighten the four rear slide-rail bracket screws at this time.
Rail-alignment spacer
12. If you are not replacing the inner-slide rails attached to the monitor and
keyboard tray, go to step 14.
13. Remove the screw and the nut that attach the inner slide rails to the monitor
and keyboard assembly; then, attach the corresponding new inner slide rails
to the tray using the same hardware.
14. Go to step 13 on page 11 for instructions for reinstalling the monitor and
keyboard tray in the rack cabinet; then, install any other devices that you
removed from the rack cabinet.
24
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
Replacing the keyboard
Complete the following steps to replace a keyboard on the monitor and keyboard
tray assembly:
1. Remove the two back rubber pads from the bottom of the new keyboard and
discard them. (The rubber pads have an adhesive backing and can be peeled
from the surface.) If you leave the rubber pads on the keyboard, they will
extend into the 1-U space below.
Remove rubber pads
(two places)
Keyboard foot
2.
3.
4.
5.
Attention: Do not extend the keyboard feet. The flat-panel monitor screen
might be damaged if the feet are extended when the monitor is closed.
Turn off the monitor; then, disconnect the monitor cord.
Disconnect the keyboard and mouse connectors from the server or console
switch.
Unscrew the thumbscrews; then, fully extend the monitor and keyboard tray.
Remove the keyboard-and-mouse cable from the cable-management arm.
Carefully lift the front of the flat-panel monitor and raise the monitor to the full
upright position.
Thumbscrews
6. Remove the old keyboard from the keyboard tray.
Chapter 3. Hardware maintenance information
25
nd
pa
E
ac
ks
te
B
|
nte
r
}
=
E
]
{
-
;
hif
t
C
lt
A
H
M
Y
,
J
<
.
K
U
7
7
F
6
F
6
5
N
G
5
T
F
4
F
B
R
F
4
3
V
D
3
E
F
2
sc
C
X
F
n
C
tr
S
l
hif
t
C
ap
A
s
lt
Lo
Ta
b
ck
Z
`
A
~
1
Q
F
1
S
2
W
F
E
tr
l
>
I
/
L
8
F
8
?
O
9
F
9
:
‘
S
“
P
0
F
10
[
P
F
rtS
c
11
_
S
F
cr
Lk
12
+
\
P
au
D
se
ele
In
se
rt
7. Carefully set the new keyboard into the tray; then, route the
keyboard-and-mouse cable through the cord clip on the bottom, up through the
opening on the right side of the tray, and toward the cable-management arm.
Pull the full length of the cable through the opening.
Keyboard-and-mouse
cable routing
8. Secure the keyboard-and-mouse cable to the cable-management arm using the
existing cable straps.
9. Reconnect the keyboard-and-mouse cable to the server or console switch.
Note: When the monitor and keyboard are not in use, if the rack cabinet is in a
vibration-prone area, or during cabinet relocation, tighten the two
thumbscrews on the front of the tray to secure the tray inside the rack
cabinet.
Thumbscrew
26
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
Appendix A. Getting help and technical assistance
If you need help, service, or technical assistance or just want more information
about IBM products, you will find a wide variety of sources available from IBM to
assist you. This appendix contains information about where to go for additional
information about IBM and IBM products, what to do if you experience a problem
with your xSeries or IntelliStation® system, and whom to call for service, if it is
necessary.
Before you call
Before you call, make sure that you have taken these steps to try to solve the
problem yourself:
v Check all cables to make sure that they are connected.
v Check the power switches to make sure that the system is turned on.
v Use the troubleshooting information in your system documentation, and use the
diagnostic tools that come with your system.
v Go to the IBM Support Web site at http://www.ibm.com/pc/support/ to check
for technical information, hints, tips, and new device drivers or to submit a
request for information.
You can solve many problems without outside assistance by following the
troubleshooting procedures that IBM provides in the online help or in the
publications that are provided with your system and software. The information
that comes with your system also describes the diagnostic tests that you can
perform. Most xSeries and IntelliStation systems, operating systems, and programs
come with information that contains troubleshooting procedures and explanations
of error messages and error codes. If you suspect a software problem, see the
information for the operating system or program.
Using the documentation
Information about your IBM xSeries or IntelliStation system and preinstalled
software, if any, is available in the documentation that comes with your system.
That documentation includes printed books, online books, readme files, and help
files. See the troubleshooting information in your system documentation for
instructions for using the diagnostic programs. The troubleshooting information or
the diagnostic programs might tell you that you need additional or updated device
drivers or other software. IBM maintains pages on the World Wide Web where you
can get the latest technical information and download device drivers and updates.
To access these pages, go to http://www.ibm.com/pc/support/ and follow the
instructions. Also, you can order publications through the IBM Publications
Ordering System at
http://www.elink.ibmlink.ibm.com/public/applications/publications/cgibin/pbi.cgi.
Getting help and information from the World Wide Web
On the World Wide Web, the IBM Web site has up-to-date information about IBM
xSeries and IntelliStation products, services, and support. The address for IBM
xSeries information is http://www.ibm.com/eserver/xseries/. The address for IBM
IntelliStation information is http://www.ibm.com/pc/intellistation/.
© Copyright IBM Corp. 2004
27
You can find service information for your IBM products, including supported
options, at http://www.ibm.com/pc/support/.
Software service and support
Through IBM Support Line, you can get telephone assistance, for a fee, with usage,
configuration, and software problems with xSeries servers, IntelliStation
workstations, and appliances. For information about which products are supported
by Support Line in your country or region, go to
http://www.ibm.com/services/sl/products/.
For more information about Support Line and other IBM services, go to
http://www.ibm.com/services/, or go to http://www.ibm.com/planetwide/ for
support telephone numbers. In the U.S. and Canada, call 1-800-IBM-SERV
(1-800-426-7378).
Hardware service and support
You can receive hardware service through IBM Integrated Technology Services or
through your IBM reseller, if your reseller is authorized by IBM to provide
warranty service. Go to http://www.ibm.com/planetwide/ for support telephone
numbers, or in the U.S. and Canada, call 1-800-IBM-SERV (1-800-426-7378).
In the U.S. and Canada, hardware service and support is available 24 hours a day,
7 days a week. In the U.K., these services are available Monday through Friday,
from 9 a.m. to 6 p.m.
28
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
Appendix B. IBM Statement of Limited Warranty Z125-4753-07
11/2002
Part 1 - General Terms
Part 1 - General Terms
This Statement of Limited Warranty includes Part 1 - General Terms, Part 2 Country-unique Terms, and Part 3 - Warranty Information. The terms of Part 2 replace or
modify those of Part 1. The warranties provided by IBM in this Statement of Limited
Warranty apply only to Machines you purchase for your use, and not for resale. The term
“Machine” means an IBM machine, its features, conversions, upgrades, elements, or
accessories, or any combination of them. The term “Machine” does not include any
software programs, whether pre-loaded with the Machine, installed subsequently or
otherwise. Nothing in this Statement of Limited Warranty affects any statutory
rights of consumers that cannot be waived or limited by contract.
What this Warranty Covers
IBM warrants that each Machine 1) is free from defects in materials and
workmanship and 2) conforms to IBM’s Official Published Specifications
(“Specifications”) which are available on request. The warranty period for the
Machine starts on the original Date of Installation and is specified in Part 3 Warranty Information. The date on your invoice or sales receipt is the Date of
Installation unless IBM or your reseller informs you otherwise. Many features,
conversions, or upgrades involve the removal of parts and their return to IBM. A
part that replaces a removed part will assume the warranty service status of the
removed part. Unless IBM specifies otherwise, these warranties apply only in the
country or region in which you purchased the Machine.
THESE WARRANTIES ARE YOUR EXCLUSIVE WARRANTIES AND REPLACE
ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OR
CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. SOME STATES OR JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OF EXPRESS OR IMPLIED WARRANTIES, SO THE ABOVE
EXCLUSION MAY NOT APPLY TO YOU. IN THAT EVENT, SUCH
WARRANTIES ARE LIMITED IN DURATION TO THE WARRANTY PERIOD.
NO WARRANTIES APPLY AFTER THAT PERIOD. SOME STATES OR
JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT
APPLY TO YOU.
What this Warranty Does not Cover
This warranty does not cover the following:
v any software programs, whether pre-loaded or shipped with the Machine, or
installed subsequently;
v failure resulting from misuse (including but not limited to use of any Machine
capacity or capability, other than that authorized by IBM in writing), accident,
modification, unsuitable physical or operating environment, or improper
maintenance by you;
v failure caused by a product for which IBM is not responsible; and
© Copyright IBM Corp. 2004
29
v
any non-IBM products, including those that IBM may procure and provide with
or integrate into an IBM Machine at your request.
The warranty is voided by removal or alteration of identification labels on the
Machine or its parts.
IBM does not warrant uninterrupted or error-free operation of a Machine.
Any technical or other support provided for a Machine under warranty, such as
assistance via telephone with “how-to” questions and those regarding Machine
set-up and installation, is provided WITHOUT WARRANTIES OF ANY KIND.
How to Obtain Warranty Service
If the Machine does not function as warranted during the warranty period, contact
IBM or your reseller to obtain warranty service. If you do not register the Machine
with IBM, you may be required to present proof of purchase as evidence of your
entitlement to warranty service.
What IBM Will Do to Correct Problems
When you call for service, you must follow the problem determination and
resolution procedures that IBM specifies. A technician will attempt to make an
initial diagnosis of your problem and help you resolve it over the telephone.
The type of warranty service applicable to your Machine is specified in Part 3 Warranty Information.
You are responsible for downloading and installing designated Machine Code
(microcode, basic input/output system code (called “BIOS”), utility programs,
device drivers, and diagnostics delivered with an IBM Machine) and other
software updates from an IBM Internet Web site or from other electronic media,
and following the instructions that IBM provides.
If your problem can be resolved with a Customer Replaceable Unit (“CRU”) (e.g.,
keyboard, mouse, speaker, memory, hard disk drive and other easily replaceable
parts), IBM will ship these parts to you for replacement by you.
If the Machine does not function as warranted during the warranty period and
your problem cannot be resolved over the telephone, through your application of
Machine Code or software updates, or with a CRU, IBM or your reseller, if
approved by IBM to provide warranty service, will either, at its discretion, 1) repair
it to make it function as warranted, or 2) replace it with one that is at least
functionally equivalent. If IBM is unable to do either, you may return the Machine
to your place of purchase and your money will be refunded.
IBM or your reseller will also manage and install selected engineering changes that
apply to the Machine.
Exchange of a Machine or Part
When the warranty service involves the exchange of a Machine or part, the item
IBM or your reseller replaces becomes its property and the replacement becomes
yours. You represent that all removed items are genuine and unaltered. The
replacement may not be new, but will be in good working order and at least
30
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
functionally equivalent to the item replaced. The replacement assumes the
warranty service status of the replaced item.
Your Additional Responsibilities
Before IBM or your reseller exchanges a Machine or part, you agree to remove all
features, parts, options, alterations, and attachments not under warranty service.
You also agree to:
1. ensure that the Machine is free of any legal obligations or restrictions that
prevent its exchange;
2. obtain authorization from the owner to have IBM or your reseller service a
Machine that you do not own; and
3. where applicable, before service is provided:
a. follow the service request procedures that IBM or your reseller provides;
b. backup or secure all programs, data, and funds contained in the Machine;
c. provide IBM or your reseller with sufficient, free, and safe access to your
facilities to permit IBM to fulfill its obligations; and
d. inform IBM or your reseller of changes in the Machine’s location.
4. (a) ensure all information about identified or identifiable individuals (Personal
Data) is deleted from the Machine (to the extent technically possible), (b) allow
IBM, your reseller or an IBM supplier to process on your behalf any remaining
Personal Data as IBM or your reseller considers necessary to fulfill its
obligations under this Statement of Limited Warranty (which may include
shipping the Machine for such processing to other IBM service locations around
the world), and (c) ensure that such processing complies with any laws
applicable to such Personal Data.
Limitation of Liability
IBM is responsible for loss of, or damage to, your Machine only while it is 1) in
IBM’s possession or 2) in transit in those cases where IBM is responsible for the
transportation charges.
Neither IBM nor your reseller are responsible for any of your confidential,
proprietary or personal information contained in a Machine which you return to
IBM for any reason. You should remove all such information from the Machine
prior to its return.
Circumstances may arise where, because of a default on IBM’s part or other
liability, you are entitled to recover damages from IBM. In each such instance,
regardless of the basis on which you are entitled to claim damages from IBM
(including fundamental breach, negligence, misrepresentation, or other contract or
tort claim), except for any liability that cannot be waived or limited by applicable
laws, IBM is liable for no more than
1. damages for bodily injury (including death) and damage to real property and
tangible personal property; and
2. the amount of any other actual direct damages, up to the charges (if recurring,
12 months’ charges apply) for the Machine that is subject of the claim. For
purposes of this item, the term “Machine” includes Machine Code and
Licensed Internal Code (“LIC”).
This limit also applies to IBM’s suppliers and your reseller. It is the maximum for
which IBM, its suppliers, and your reseller are collectively responsible.
Appendix B. IBM Statement of Limited Warranty Z125-4753-07 11/2002
31
UNDER NO CIRCUMSTANCES IS IBM, ITS SUPPLIERS OR RESELLERS
LIABLE FOR ANY OF THE FOLLOWING EVEN IF INFORMED OF THEIR
POSSIBILITY: 1) THIRD PARTY CLAIMS AGAINST YOU FOR DAMAGES
(OTHER THAN THOSE UNDER THE FIRST ITEM LISTED ABOVE); 2) LOSS
OF, OR DAMAGE TO, DATA; 3) SPECIAL, INCIDENTAL, OR INDIRECT
DAMAGES OR FOR ANY ECONOMIC CONSEQUENTIAL DAMAGES; OR 4)
LOST PROFITS, BUSINESS REVENUE, GOODWILL OR ANTICIPATED
SAVINGS. SOME STATES OR JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY
TO YOU. SOME STATES OR JURISDICTIONS DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE
ABOVE LIMITATION MAY NOT APPLY TO YOU.
Governing Law
Both you and IBM consent to the application of the laws of the country in which
you acquired the Machine to govern, interpret, and enforce all of your and IBM’s
rights, duties, and obligations arising from, or relating in any manner to, the
subject matter of this Statement of Limited Warranty, without regard to conflict of
law principles.
THESE WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS AND YOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR
JURISDICTION TO JURISDICTION.
Jurisdiction
All of our rights, duties, and obligations are subject to the courts of the country in
which you acquired the Machine.
Part 2 - Country-unique Terms
AMERICAS
ARGENTINA
Governing Law: The following is added after the first sentence:
Any litigation arising from this Statement of Limited Warranty will be settled
exclusively by the Ordinary Commercial Court of the city of Buenos Aires.
BRAZIL
Governing Law: The following is added after the first sentence:
Any litigation arising from this Statement of Limited Warranty will be settled
exclusively by the court of Rio de Janeiro, RJ.
PERU
Limitation of Liability: The following is added at the end of this section:
In accordance with Article 1328 of the Peruvian Civil Code the limitations and
exclusions specified in this section will not apply to damages caused by IBM’s
willful misconduct (“dolo”) or gross negligence (“culpa inexcusable”).
32
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
NORTH AMERICA
How to Obtain Warranty Service: The following is added to this Section:
To obtain warranty service from IBM in Canada or the United States, call
1-800-IBM-SERV (426-7378).
CANADA
Limitation of Liability: The following replaces item 1 of this section:
1. damages for bodily injury (including death) or physical harm to real property
and tangible personal property caused by IBM’s negligence; and
Governing Law: The following replaces “laws of the country in which you acquired the
Machine” in the first sentence:
laws in the Province of Ontario.
UNITED STATES
Governing Law: The following replaces “laws of the country in which you acquired the
Machine” in the first sentence:
laws of the State of New York.
ASIA PACIFIC
AUSTRALIA
What this Warranty Covers: The following paragraph is added to this section:
The warranties specified in this Section are in addition to any rights you may have
under the Trade Practices Act 1974 or other similar legislation and are only limited
to the extent permitted by the applicable legislation.
Limitation of Liability: The following is added to this section:
Where IBM is in breach of a condition or warranty implied by the Trade Practices
Act 1974 or other similar legislation, IBM’s liability is limited to the repair or
replacement of the goods or the supply of equivalent goods. Where that condition
or warranty relates to right to sell, quiet possession or clear title, or the goods are
of a kind ordinarily acquired for personal, domestic or household use or
consumption, then none of the limitations in this paragraph apply.
Governing Law: The following replaces “laws of the country in which you acquired the
Machine” in the first sentence:
laws of the State or Territory.
CAMBODIA, LAOS, AND VIETNAM
Governing Law: The following replaces “laws of the country in which you acquired the
Machine” in the first sentence:
laws of the State of New York, United States of America.
CAMBODIA, INDONESIA, LAOS, AND VIETNAM
Arbitration: The following is added under this heading:
Disputes arising out of or in connection with this Statement of Limited Warranty
shall be finally settled by arbitration which shall be held in Singapore in
accordance with the Arbitration Rules of Singapore International Arbitration Center
Appendix B. IBM Statement of Limited Warranty Z125-4753-07 11/2002
33
(“SIAC Rules”) then in effect. The arbitration award shall be final and binding for
the parties without appeal and shall be in writing and set forth the findings of fact
and the conclusions of law.
The number of arbitrators shall be three, with each side to the dispute being
entitled to appoint one arbitrator. The two arbitrators appointed by the parties
shall appoint a third arbitrator who shall act as chairman of the proceedings.
Vacancies in the post of chairman shall be filled by the president of the SIAC.
Other vacancies shall be filled by the respective nominating party. Proceedings
shall continue from the stage they were at when the vacancy occurred.
If one of the parties refuses or otherwise fails to appoint an arbitrator within 30
days of the date the other party appoints its, the first appointed arbitrator shall be
the sole arbitrator, provided that the arbitrator was validly and properly
appointed.
All proceedings shall be conducted, including all documents presented in such
proceedings, in the English language. The English language version of this
Statement of Limited Warranty prevails over any other language version.
HONG KONG S.A.R. OF CHINA AND MACAU S.A.R. OF CHINA
Governing Law: The following replaces “laws of the country in which you acquired the
Machine” in the first sentence:
laws of Hong Kong Special Administrative Region of China.
INDIA
Limitation of Liability: The following replaces items 1 and 2 of this section:
1. liability for bodily injury (including death) or damage to real property and
tangible personal property will be limited to that caused by IBM’s negligence;
and
2. as to any other actual damage arising in any situation involving
nonperformance by IBM pursuant to, or in any way related to the subject of
this Statement of Limited Warranty, the charge paid by you for the individual
Machine that is the subject of the claim. For purposes of this item, the term
“Machine” includes Machine Code and Licensed Internal Code (“LIC”).
Arbitration: The following is added under this heading:
Disputes arising out of or in connection with this Statement of Limited Warranty
shall be finally settled by arbitration which shall be held in Bangalore, India in
accordance with the laws of India then in effect. The arbitration award shall be
final and binding for the parties without appeal and shall be in writing and set
forth the findings of fact and the conclusions of law.
The number of arbitrators shall be three, with each side to the dispute being
entitled to appoint one arbitrator. The two arbitrators appointed by the parties
shall appoint a third arbitrator who shall act as chairman of the proceedings.
Vacancies in the post of chairman shall be filled by the president of the Bar
Council of India. Other vacancies shall be filled by the respective nominating party.
Proceedings shall continue from the stage they were at when the vacancy occurred.
34
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
If one of the parties refuses or otherwise fails to appoint an arbitrator within 30
days of the date the other party appoints its, the first appointed arbitrator shall be
the sole arbitrator, provided that the arbitrator was validly and properly
appointed.
All proceedings shall be conducted, including all documents presented in such
proceedings, in the English language. The English language version of this
Statement of Limited Warranty prevails over any other language version.
JAPAN
Governing Law: The following sentence is added to this section:
Any doubts concerning this Statement of Limited Warranty will be initially
resolved between us in good faith and in accordance with the principle of mutual
trust.
MALAYSIA
Limitation of Liability: The word “SPECIAL” in item 3 of the fifth paragraph is
deleted.
NEW ZEALAND
What this Warranty Covers: The following paragraph is added to this section:
The warranties specified in this section are in addition to any rights you may have
under the Consumer Guarantees Act 1993 or other legislation which cannot be
excluded or limited. The Consumer Guarantees Act 1993 will not apply in respect
of any goods which IBM provides, if you require the goods for the purposes of a
business as defined in that Act.
Limitation of Liability: The following is added to this section:
Where Machines are not acquired for the purposes of a business as defined in the
Consumer Guarantees Act 1993, the limitations in this section are subject to the
limitations in that Act.
PEOPLE’S REPUBLIC OF CHINA (PRC)
Governing Law: The following replaces “laws of the country in which you acquired the
Machine” in the first sentence:
laws of the State of New York, United States of America (except when local law
requires otherwise).
PHILIPPINES
Limitation of Liability: Item 3 in the fifth paragraph is replaced by the following:
SPECIAL (INCLUDING NOMINAL AND EXEMPLARY DAMAGES), MORAL,
INCIDENTAL, OR INDIRECT DAMAGES FOR ANY ECONOMIC
CONSEQUENTIAL DAMAGES; OR
Arbitration: The following is added under this heading:
Disputes arising out of or in connection with this Statement of Limited Warranty
shall be finally settled by arbitration which shall be held in Metro Manila,
Philippines in accordance with the laws of the Philippines then in effect. The
Appendix B. IBM Statement of Limited Warranty Z125-4753-07 11/2002
35
arbitration award shall be final and binding for the parties without appeal and
shall be in writing and set forth the findings of fact and the conclusions of law.
The number of arbitrators shall be three, with each side to the dispute being
entitled to appoint one arbitrator. The two arbitrators appointed by the parties
shall appoint a third arbitrator who shall act as chairman of the proceedings.
Vacancies in the post of chairman shall be filled by the president of the Philippine
Dispute Resolution Center, Inc. Other vacancies shall be filled by the respective
nominating party. Proceedings shall continue from the stage they were at when the
vacancy occurred.
If one of the parties refuses or otherwise fails to appoint an arbitrator within 30
days of the date the other party appoints its, the first appointed arbitrator shall be
the sole arbitrator, provided that the arbitrator was validly and properly
appointed.
All proceedings shall be conducted, including all documents presented in such
proceedings, in the English language. The English language version of this
Statement of Limited Warranty prevails over any other language version.
SINGAPORE
Limitation of Liability: The words “SPECIAL” and “ECONOMIC” in item 3 in the
fifth paragraph are deleted.
EUROPE, MIDDLE EAST, AFRICA (EMEA)
THE FOLLOWING TERMS APPLY TO ALL EMEA COUNTRIES:
The terms of this Statement of Limited Warranty apply to Machines purchased
from IBM or an IBM reseller.
Hot to Obtain Warranty Service: If you purchase a Machine in Austria, Belgium,
Cyprus, Denmark, Estonia, Finland, France, Germany, Greece, Iceland, Ireland,
Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Monaco, Netherlands, Norway,
Portugal, Spain, San Marino, Sweden, Switzerland, United Kingdom or Vatican
State, you may obtain warranty service for that Machine in any of those countries
from either (1) an IBM reseller approved to perform warranty service or (2) from
IBM, provided the Machine has been announced and made available by IBM in the
country in which you wish to obtain service. If you purchased a Personal
Computer Machine in Albania, Armenia, Belarus, Bosnia and Herzegovina,
Bulgaria, Croatia, Czech Republic, Georgia, Hungary, Kazakhstan, Kyrgyzstan,
Federal Republic of Yugoslavia, Former Yugoslav Republic of Macedonia (FYROM),
Moldova, Poland, Romania, Russia, Slovak Republic, Slovenia, or Ukraine, you
may obtain warranty service for that Machine in any of those countries from either
(1) an IBM reseller approved to perform warranty service or (2) from IBM.
If you purchase a Machine in a Middle Eastern or African country, you may obtain
warranty service for that Machine from the IBM entity within the country of
purchase, if that IBM entity provides warranty service in that country, or from an
IBM reseller, approved by IBM to perform warranty service on that Machine in
that country. Warranty service in Africa is available within 50 kilometers of an IBM
approved service provider. You are responsible for transportation costs for
Machines located outside 50 kilometers of an IBM approved service provider.
36
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
Add the following paragraph in Western Europe (Austria, Belgium, Cyprus, Denmark,
Finland, France, Germany, Greece, Iceland, Ireland, Italy, Liechtenstein, Luxembourg,
Monaco, Netherlands, Norway, Portugal, Spain, San Marino, Sweden, Switzerland, United
Kingdom, Vatican State):
The warranty for Machines acquired in Western Europe shall be valid and
applicable in all Western Europe countries provided the Machines have been
announced and made available in such countries.
Governing Law:
The phrase “the laws of the country in which you acquired the Machine” is replaced by:
1) “the laws of Austria” in Albania, Armenia, Azerbaijan, Belarus,
Bosnia-Herzegovina, Bulgaria, Croatia, Georgia, Hungary, Kazakhstan,
Kyrgyzstan, FYR Macedonia, Moldova, Poland, Romania, Russia, Slovakia,
Slovenia, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, and FR Yugoslavia; 2)
“the laws of France” in Algeria, Benin, Burkina Faso, Cameroon, Cape Verde,
Central African Republic, Chad, Comoros, Congo Republic, Djibouti, Democratic
Republic of Congo, Equatorial Guinea, French Guiana, French Polynesia, Gabon,
Gambia, Guinea, Guinea-Bissau, Ivory Coast, Lebanon, Madagascar, Mali,
Mauritania, Mauritius, Mayotte, Morocco, New Caledonia, Niger, Reunion,
Senegal, Seychelles, Togo, Tunisia, Vanuatu, and Wallis & Futuna; 3) “the laws of
Finland” in Estonia, Latvia, and Lithuania; 4) “the laws of England” in Angola,
Bahrain, Botswana, Burundi, Egypt, Eritrea, Ethiopia, Ghana, Jordan, Kenya,
Kuwait, Liberia, Malawi, Malta, Mozambique, Nigeria, Oman, Pakistan, Qatar,
Rwanda, Sao Tome, Saudi Arabia, Sierra Leone, Somalia, Tanzania, Uganda,
United Arab Emirates, the United Kingdom, West Bank/Gaza, Yemen, Zambia,
and Zimbabwe; and 5) “the laws of South Africa” in South Africa, Namibia,
Lesotho and Swaziland.
Jurisdiction: The following exceptions are added to this section:
1) In Austria the choice of jurisdiction for all disputes arising out of this Statement
of Limited Warranty and relating thereto, including its existence, will be the
competent court of law in Vienna, Austria (Inner-City); 2) in Angola, Bahrain,
Botswana, Burundi, Egypt, Eritrea, Ethiopia, Ghana, Jordan, Kenya, Kuwait,
Liberia, Malawi, Malta, Mozambique, Nigeria, Oman, Pakistan, Qatar, Rwanda,
Sao Tome, Saudi Arabia, Sierra Leone, Somalia, Tanzania, Uganda, United Arab
Emirates, West Bank/Gaza, Yemen, Zambia, and Zimbabwe all disputes arising
out of this Statement of Limited Warranty or related to its execution, including
summary proceedings, will be submitted to the exclusive jurisdiction of the English
courts; 3) in Belgium and Luxembourg, all disputes arising out of this Statement
of Limited Warranty or related to its interpretation or its execution, the law, and
the courts of the capital city, of the country of your registered office and/or
commercial site location only are competent; 4) in France, Algeria, Benin, Burkina
Faso, Cameroon, Cape Verde, Central African Republic, Chad, Comoros, Congo
Republic, Djibouti, Democratic Republic of Congo, Equatorial Guinea, French
Guiana, French Polynesia, Gabon, Gambia, Guinea, Guinea-Bissau, Ivory Coast,
Lebanon, Madagascar, Mali, Mauritania, Mauritius, Mayotte, Morocco, New
Caledonia, Niger, Reunion, Senegal, Seychelles, Togo, Tunisia, Vanuatu, and
Wallis & Futuna all disputes arising out of this Statement of Limited Warranty or
related to its violation or execution, including summary proceedings, will be
settled exclusively by the Commercial Court of Paris; 5) in Russia, all disputes
arising out of or in relation to the interpretation, the violation, the termination, the
nullity of the execution of this Statement of Limited Warranty shall be settled by
Appendix B. IBM Statement of Limited Warranty Z125-4753-07 11/2002
37
Arbitration Court of Moscow; 6) in South Africa, Namibia, Lesotho and
Swaziland, both of us agree to submit all disputes relating to this Statement of
Limited Warranty to the jurisdiction of the High Court in Johannesburg; 7) in
Turkey all disputes arising out of or in connection with this Statement of Limited
Warranty shall be resolved by the Istanbul Central (Sultanahmet) Courts and
Execution Directorates of Istanbul, the Republic of Turkey; 8) in each of the
following specified countries, any legal claim arising out of this Statement of
Limited Warranty will be brought before, and settled exclusively by, the competent
court of a) Athens for Greece, b) Tel Aviv-Jaffa for Israel, c) Milan for Italy, d)
Lisbon for Portugal, and e) Madrid for Spain; and 9) in the United Kingdom, both
of us agree to submit all disputes relating to this Statement of Limited Warranty to
the jurisdiction of the English courts.
Arbitration: The following is added under this heading:
In Albania, Armenia, Azerbaijan, Belarus, Bosnia-Herzegovina, Bulgaria, Croatia,
Georgia, Hungary, Kazakhstan, Kyrgyzstan, FYR Macedonia, Moldova, Poland,
Romania, Russia, Slovakia, Slovenia, Tajikistan, Turkmenistan, Ukraine,
Uzbekistan, and FR Yugoslavia all disputes arising out of this Statement of
Limited Warranty or related to its violation, termination or nullity will be finally
settled under the Rules of Arbitration and Conciliation of the International Arbitral
Center of the Federal Economic Chamber in Vienna (Vienna Rules) by three
arbitrators appointed in accordance with these rules. The arbitration will be held in
Vienna, Austria, and the official language of the proceedings will be English. The
decision of the arbitrators will be final and binding upon both parties. Therefore,
pursuant to paragraph 598 (2) of the Austrian Code of Civil Procedure, the parties
expressly waive the application of paragraph 595 (1) figure 7 of the Code. IBM
may, however, institute proceedings in a competent court in the country of
installation.
In Estonia, Latvia and Lithuania all disputes arising in connection with this
Statement of Limited Warranty will be finally settled in arbitration that will be
held in Helsinki, Finland in accordance with the arbitration laws of Finland then in
effect. Each party will appoint one arbitrator. The arbitrators will then jointly
appoint the chairman. If arbitrators cannot agree on the chairman, then the Central
Chamber of Commerce in Helsinki will appoint the chairman.
EUROPEAN UNION (EU)
THE FOLLOWING TERMS APPLY TO ALL EU COUNTRIES:
Consumers have legal rights under applicable national legislation governing the
sale of consumer goods. Such rights are not affected by the warranties provided in
this Statement of Limited Warranty.
How to Obtain Warranty Service: The following is added to this section:
To obtain warranty service from IBM in EU countries, see the telephone listing in
Part 3 - Warranty Information.
You may contact IBM at the following address:
IBM Warranty & Service Quality Dept.
PO Box 30
Spango Valley
Greenock
Scotland PA16 0AH
38
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
AUSTRIA, DENMARK, FINLAND, GREECE, ITALY, NETHERLANDS,
PORTUGAL, SPAIN, SWEDEN AND SWITZERLAND
Limitation of Liability: The following replaces the terms of this section in its entirety:
Except as otherwise provided by mandatory law:
1. IBM’s liability for any damages and losses that may arise as a consequence of
the fulfillment of its obligations under or in connection with this Statement of
Limited Warranty or due to any other cause related to this Statement of
Limited Warranty is limited to the compensation of only those damages and
losses proved and actually arising as an immediate and direct consequence of
the non-fulfillment of such obligations (if IBM is at fault) or of such cause, for a
maximum amount equal to the charges you paid for the Machine. For purposes
of this item, the term “Machine” includes Machine Code and Licensed Internal
Code (“LIC”).
The above limitation shall not apply to damages for bodily injuries (including
death) and damages to real property and tangible personal property for which
IBM is legally liable.
2. UNDER NO CIRCUMSTANCES IS IBM, ITS SUPPLIERS OR RESELLERS
LIABLE FOR ANY OF THE FOLLOWING, EVEN IF INFORMED OF THEIR
POSSIBILITY: 1) LOSS OF, OR DAMAGE TO, DATA; 2) INCIDENTAL OR
INDIRECT DAMAGES, OR FOR ANY ECONOMIC CONSEQUENTIAL
DAMAGES; 3) LOST PROFITS, EVEN IF THEY ARISE AS AN IMMEDIATE
CONSEQUENCE OF THE EVENT THAT GENERATED THE DAMAGES;
OR 4) LOSS OF BUSINESS, REVENUE, GOODWILL, OR ANTICIPATED
SAVINGS.
FRANCE AND BELGIUM
Limitation of Liability: The following replaces the terms of this section in its entirety:
Except as otherwise provided by mandatory law:
1. IBM’s liability for any damages and losses that may arise as a consequence of
the fulfillment of its obligations under or in connection with this Statement of
Limited Warranty is limited to the compensation of only those damages and
losses proved and actually arising as an immediate and direct consequence of
the non-fulfillment of such obligations (if IBM is at fault), for a maximum
amount equal to the charges you paid for the Machine that has caused the
damages. For purposes of this item, the term “Machine” includes Machine
Code and Licensed Internal Code (“LIC”).
The above limitation shall not apply to damages for bodily injuries (including
death) and damages to real property and tangible personal property for which
IBM is legally liable.
2. UNDER NO CIRCUMSTANCES IS IBM, ITS SUPPLIERS OR RESELLERS
LIABLE FOR ANY OF THE FOLLOWING, EVEN IF INFORMED OF THEIR
POSSIBILITY: 1) LOSS OF, OR DAMAGE TO, DATA; 2) INCIDENTAL OR
INDIRECT DAMAGES, OR FOR ANY ECONOMIC CONSEQUENTIAL
DAMAGES; 3) LOST PROFITS, EVEN IF THEY ARISE AS AN IMMEDIATE
CONSEQUENCE OF THE EVENT THAT GENERATED THE DAMAGES;
OR 4) LOSS OF BUSINESS, REVENUE, GOODWILL, OR ANTICIPATED
SAVINGS.
Appendix B. IBM Statement of Limited Warranty Z125-4753-07 11/2002
39
THE FOLLOWING TERMS APPLY TO THE COUNTRY SPECIFIED:
AUSTRIA
What this Warranty Covers: The following replaces the first sentence of the first
paragraph of this section:
The warranty for an IBM Machine covers the functionality of the Machine for its
normal use and the Machine’s conformity to its Specifications.
The following paragraphs are added to this section:
The warranty period for Machines is 12 months from the date of delivery. The
limitation period for consumers in action for breach of warranty is the statutory
period as a minimum. In case IBM or your reseller is unable to repair an IBM
Machine, you can alternatively ask for a partial refund as far as justified by the
reduced value of the unrepaired Machine or ask for a cancellation of the respective
agreement for such Machine and get your money refunded.
The second paragraph does not apply.
What IBM Will Do to Correct Problems: The following is added to this section:
During the warranty period, transportation for delivery of the failing Machine to
IBM will be at IBM’s expense.
Limitation of Liability: The following paragraph is added to this section:
The limitations and exclusions specified in the Statement of Limited Warranty will
not apply to damages caused by IBM with fraud or gross negligence and for
express warranty.
The following sentence is added to the end of item 2:
IBM’s liability under this item is limited to the violation of essential contractual
terms in cases of ordinary negligence.
EGYPT
Limitation of Liability: The following replaces item 2 in this section:
as to any other actual direct damages, IBM’s liability will be limited to the total
amount you paid for the Machine that is the subject of the claim. For purposes of
this item, the term “Machine” includes Machine Code and Licensed Internal Code
(“LIC”).
Applicability of suppliers and resellers (unchanged).
FRANCE
Limitation of Liability: The following replaces the second sentence of the first paragraph
of this section:
In such instances, regardless of the basis on which you are entitled to claim
damages from IBM, IBM is liable for no more than: (items 1 and 2 unchanged).
40
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
GERMANY
What this Warranty Covers: The following replaces the first sentence of the first
paragraph of this section:
The warranty for an IBM Machine covers the functionality of the Machine for its
normal use and the Machine’s conformity to its Specifications.
The following paragraphs are added to this section:
The minimum warranty period for Machines is twelve months. In case IBM or
your reseller is unable to repair an IBM Machine, you can alternatively ask for a
partial refund as far as justified by the reduced value of the unrepaired Machine or
ask for a cancellation of the respective agreement for such Machine and get your
money refunded.
The second paragraph does not apply.
What IBM Will Do to Correct Problems: The following is added to this section:
During the warranty period, transportation for delivery of the failing Machine to
IBM will be at IBM’s expense.
Limitation of Liability: The following paragraph is added to this section:
The limitations and exclusions specified in the Statement of Limited Warranty will
not apply to damages caused by IBM with fraud or gross negligence and for
express warranty.
The following sentence is added to the end of item 2:
IBM’s liability under this item is limited to the violation of essential contractual
terms in cases of ordinary negligence.
HUNGARY
Limitation of Liability: The following is added at the end of this section:
The limitation and exclusion specified herein shall not apply to liability for a
breach of contract damaging life, physical well-being, or health that has been
caused intentionally, by gross negligence, or by a criminal act.
The parties accept the limitations of liability as valid provisions and state that the
Section 314.(2) of the Hungarian Civil Code applies as the acquisition price as well
as other advantages arising out of the present Statement of Limited Warranty
balance this limitation of liability.
IRELAND
What this Warranty Covers: The following is added to this section:
Except as expressly provided in these terms and conditions, all statutory
conditions, including all warranties implied, but without prejudice to the generality
of the foregoing all warranties implied by the Sale of Goods Act 1893 or the Sale of
Goods and Supply of Services Act 1980 are hereby excluded.
Limitation of Liability: The following replaces the terms of this section in its entirety:
Appendix B. IBM Statement of Limited Warranty Z125-4753-07 11/2002
41
For the purposes of this section, a “Default” means any act, statement, omission, or
negligence on the part of IBM in connection with, or in relation to, the subject
matter of this Statement of Limited Warranty in respect of which IBM is legally
liable to you, whether in contract or tort. A number of Defaults which together
result in, or contribute to, substantially the same loss or damage will be treated as
one Default occurring on the date of occurrence of the last such Default.
Circumstances may arise where, because of a Default, you are entitled to recover
damages from IBM.
This section sets out the extent of IBM’s liability and your sole remedy.
1. IBM will accept unlimited liability for death or personal injury caused by the
negligence of IBM.
2. Subject always to the Items for Which IBM is Not Liable below, IBM will
accept unlimited liability for physical damage to your tangible property
resulting from the negligence of IBM.
3. Except as provided in items 1 and 2 above, IBM’s entire liability for actual
damages for any one Default will not in any event exceed the greater of 1) EUR
125,000, or 2) 125% of the amount you paid for the Machine directly relating to
the Default.
Items for Which IBM is Not Liable
Save with respect to any liability referred to in item 1 above, under no
circumstances is IBM, its suppliers or resellers liable for any of the following, even
if IBM or they were informed of the possibility of such losses:
1. loss of, or damage to, data;
2. special, indirect, or consequential loss; or
3. loss of profits, business, revenue, goodwill, or anticipated savings.
SLOVAKIA
Limitation of Liability: The following is added to the end of the last paragraph:
The limitations apply to the extent they are not prohibited under §§ 373-386 of the
Slovak Commercial Code.
SOUTH AFRICA, NAMIBIA, BOTSWANA, LESOTHO AND SWAZILAND
Limitation of Liability: The following is added to this section:
IBM’s entire liability to you for actual damages arising in all situations involving
nonperformance by IBM in respect of the subject matter of this Statement of
Warranty will be limited to the charge paid by you for the individual Machine that
is the subject of your claim from IBM.
UNITED KINGDOM
Limitation of Liability: The following replaces the terms of this section in its entirety:
For the purposes of this section, a “Default” means any act, statement, omission, or
negligence on the part of IBM in connection with, or in relation to, the subject
matter of this Statement of Limited Warranty in respect of which IBM is legally
liable to you, whether in contract or tort. A number of Defaults which together
result in, or contribute to, substantially the same loss or damage will be treated as
one Default.
42
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
Circumstances may arise where, because of a Default, you are entitled to recover
damages from IBM.
This section sets out the extent of IBM’s liability and your sole remedy.
1. IBM will accept unlimited liability for:
a. death or personal injury caused by the negligence of IBM; and
b. any breach of its obligations implied by Section 12 of the Sale of Goods Act
1979 or Section 2 of the Supply of Goods and Services Act 1982, or any
statutory modification or re-enactment of either such Section.
2. IBM will accept unlimited liability, subject always to the Items for Which IBM
is Not Liable below, for physical damage to your tangible property resulting
from the negligence of IBM.
3. IBM’s entire liability for actual damages for any one Default will not in any
event, except as provided in items 1 and 2 above, exceed the greater of 1)
Pounds Sterling 75,000, or 2) 125% of the total purchase price payable or the
charges for the Machine directly relating to the Default.
These limits also apply to IBM’s suppliers and resellers. They state the maximum
for which IBM and such suppliers and resellers are collectively responsible.
Items for Which IBM is Not Liable
Save with respect to any liability referred to in item 1 above, under no
circumstances is IBM or any of its suppliers or resellers liable for any of the
following, even if IBM or they were informed of the possibility of such losses:
1. loss of, or damage to, data;
2. special, indirect, or consequential loss; or
3. loss of profits, business, revenue, goodwill, or anticipated savings.
Part 3 - Warranty Information
This Part 3 provides information regarding the warranty applicable to your
Machine, including the warranty period and type of warranty service IBM
provides.
Warranty Period
The warranty period may vary by country or region and is specified in the table
below.
Note: “Region” means either Hong Kong or Macau Special Administrative Region
of China.
Machine: IBM 17″ 1 U Flat Panel Monitor Console Kit - machine type 1723
Country or Region of
Purchase
Warranty Period
Type of Warranty Service*
Worldwide
3 year
1 and 2
* See “Types of Warranty Service” for the legend and explanations of warranty-service
types.
A warranty period of 3 years on parts and 1 year on labor means that IBM
provides warranty service without charge for:
Appendix B. IBM Statement of Limited Warranty Z125-4753-07 11/2002
43
1. parts and labor during the first year of the warranty period; and
2. parts only, on an exchange basis, in the second and third years of the warranty
period. IBM will charge you for any labor provided in performance of the
repair or replacement(s) in the second and third year of the warranty period.
Types of Warranty Service
If required, IBM provides repair or exchange service depending on the type of
warranty service specified for your Machine in the above table and as described
below. Warranty service may be provided by your reseller if approved by IBM to
perform warranty service. Scheduling of service will depend upon the time of your
call and is subject to parts availability. Service levels are response time objectives
and are not guaranteed. The specified level of warranty service may not be
available in all worldwide locations, additional charges may apply outside IBM’s
normal service area, contact your local IBM representative or your reseller for
country and location specific information.
1. Customer Replaceable Unit (“CRU”) Service
IBM will ship CRU parts to you for your replacement. If IBM instructs you to
return the replaced CRU, you are responsible for returning it to IBM in
accordance with IBM’s instructions. If you do not return the defective CRU, if
IBM so instructs, within 30 days of your receipt of the replacement CRU, IBM
may charge you for the replacement.
2. On-site Service
IBM or your reseller will either repair or exchange the failing Machine at your
location and verify its operation. You must provide suitable working area to
allow disassembly and reassembly of the IBM Machine. The area must be clean,
well lit and suitable for the purpose. For some Machines, certain repairs may
require sending the Machine to an IBM service center.
3. Courier or Depot Service*
You will disconnect the failing Machine for collection arranged by IBM. IBM
will provide you with a shipping container for you to return your Machine to a
designated service center. A courier will pick up your Machine and deliver it to
the designated service center. Following its repair or exchange, IBM will
arrange the return delivery of the Machine to your location. You are responsible
for its installation and verification.
4. Customer Carry-In or Mail-In Service
You will deliver or mail as IBM specifies (prepaid unless IBM specifies
otherwise) the failing Machine suitably packaged to a location IBM designates.
After IBM has repaired or exchanged the Machine, IBM will make it available
for your collection or, for Mail-in Service, IBM will return it to you at IBM’s
expense, unless IBM specifies otherwise. You are responsible for the subsequent
installation and verification of the Machine.
* This type of service is called ThinkPad® EasyServ or EasyServ in some countries.
The IBM Machine Warranty World Wide Web site at
http://www.ibm.com/servers/support/machine_warranties/ provides a
worldwide overview of IBM Limited Warranty for Machines, a Glossary of IBM
definitions, Frequently Asked Questions (FAQs) and Support by Product (Machine)
with links to Product Support pages. The IBM Statement of Limited Warranty is
also available on this site in 29 languages.
44
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
To obtain warranty service contact IBM or your IBM reseller. In Canada or the
United States, call 1-800-IBM-SERV (426-7378). In the EU countries, see the
telephone numbers below.
EU Country Telephone List
Phone numbers are subject to change without notice.
Austria -- 43-1-24592-5901
Italy -- 39-02-482-9202
Belgium -- 02-718-4339
Luxembourg -- 352-360385-1
Denmark -- 4520-8200
Netherlands -- 020-514-5770
Finland -- 358-9-4591
Portugal -- 351-21-7915-147
France -- 0238-557-450
Spain -- 34-91-662-4916
Germany -- 07032-15-4920
Sweden -- 46-8-477-4420
Greece -- 30-210-688-1220
United Kingdom -- 01475-555-055
Ireland -- 353-1-815-4000
Appendix B. IBM Statement of Limited Warranty Z125-4753-07 11/2002
45
46
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
Appendix C. Notices
This information was developed for products and services offered in the U.S.A.
IBM may not offer the products, services, or features discussed in this document in
other countries. Consult your local IBM representative for information on the
products and services currently available in your area. Any reference to an IBM
product, program, or service is not intended to state or imply that only that IBM
product, program, or service may be used. Any functionally equivalent product,
program, or service that does not infringe any IBM intellectual property right may
be used instead. However, it is the user’s responsibility to evaluate and verify the
operation of any non-IBM product, program, or service.
IBM may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you
any license to these patents. You can send license inquiries, in writing, to:
IBM Director of Licensing
IBM Corporation
North Castle Drive
Armonk, NY 10504-1785
U.S.A.
INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS
PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or
implied warranties in certain transactions, therefore, this statement may not apply
to you.
This information could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. IBM may make improvements
and/or changes in the product(s) and/or the program(s) described in this
publication at any time without notice.
Any references in this information to non-IBM Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those Web
sites. The materials at those Web sites are not part of the materials for this IBM
product, and use of those Web sites is at your own risk.
IBM may use or distribute any of the information you supply in any way it
believes appropriate without incurring any obligation to you.
Edition notice
© Copyright International Business Machines Corporation 2004. All rights
reserved.
U.S. Government Users Restricted Rights — Use, duplication, or disclosure
restricted by GSA ADP Schedule Contract with IBM Corp.
© Copyright IBM Corp. 2004
47
Trademarks
The following terms are trademarks of International Business Machines
Corporation in the United States, other countries, or both:
Active Memory
Active PCI
Active PCI-X
Alert on LAN
BladeCenter
C2T Interconnect
Chipkill
EtherJet
e-business logo
Eserver
FlashCopy
IBM
IBM (logo)
IntelliStation
NetBAY
Netfinity
NetView
OS/2 WARP
Predictive Failure
Analysis
PS/2
ServeRAID
ServerGuide
ServerProven
TechConnect
ThinkPad
Tivoli
Tivoli Enterprise
Update Connector
Wake on LAN
XA-32
XA-64
X-Architecture
XceL4
XpandOnDemand
xSeries
Other company, product, or service names may be trademarks or service marks of
others.
Important notes
IBM makes no representation or warranties regarding non-IBM products and
services that are ServerProven®, including but not limited to the implied
warranties of merchantability and fitness for a particular purpose. These products
are offered and warranted solely by third parties.
IBM makes no representations or warranties with respect to non-IBM products.
Support (if any) for the non-IBM products is provided by the third party, not IBM.
Some software may differ from its retail version (if available), and may not include
user manuals or all program functionality.
Electronic emission notices
Federal Communications Commission (FCC) statement
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case the user will be required to correct the
interference at his own expense.
48
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
Properly shielded and grounded cables and connectors must be used in order to
meet FCC emission limits. IBM is not responsible for any radio or television
interference caused by using other than recommended cables and connectors or by
unauthorized changes or modifications to this equipment. Unauthorized changes
or modifications could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Industry Canada Class A emission compliance statement
This Class A digital apparatus complies with Canadian ICES-003.
Avis de conformité à la réglementation d’Industrie Canada
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du
Canada.
Australia and New Zealand Class A statement
Attention: This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
United Kingdom telecommunications safety requirement
Notice to Customers
This apparatus is approved under approval number NS/G/1234/J/100003 for
indirect connection to public telecommunication systems in the United Kingdom.
European Union EMC Directive conformance statement
This product is in conformity with the protection requirements of EU Council
Directive 89/336/EEC on the approximation of the laws of the Member States
relating to electromagnetic compatibility. IBM cannot accept responsibility for any
failure to satisfy the protection requirements resulting from a nonrecommended
modification of the product, including the fitting of non-IBM option cards.
This product has been tested and found to comply with the limits for Class A
Information Technology Equipment according to CISPR 22/European Standard EN
55022. The limits for Class A equipment were derived for commercial and
industrial environments to provide reasonable protection against interference with
licensed communication equipment.
Attention: This is a Class A product. In a domestic environment this product
may cause radio interference in which case the user may be required to take
adequate measures.
Appendix C. Notices
49
Taiwanese Class A warning statement
Chinese Class A warning statement
Japanese Voluntary Control Council for Interference (VCCI)
statement
50
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
Index
C
P
cable-management arm, replacing 19
Class A electronic emission notice 48
console switch
installing 14
rack preparation 8
parts
customer-replaceable unit (CRU) part
numbers 17
inventory checklist 1
publications, ordering 27
D
R
documentation, using
27
E
electronic emission Class A notice
48
F
FCC Class A notice 48
flat-panel monitor and keyboard tray,
installing 5
H
hardware service and support
S
safety notices v
service, getting 27
slide rails, replacing 21
software service and support
28
28
T
I
inner slide rails, replacing 21
installing
console switch 14
flat-panel monitor and keyboard
tray 5
technical assistance
tools, required 3
trademarks 48
27
U
United States electronic emission Class A
notice 48
K
keyboard, replacing 25
W
warranty 29
Web site
IBM products 28
IBM Support Line 28
IBM xSeries information
N
notices
attention 3
book 3
caution 3
danger 3
electronic emission
FCC, Class A 48
important 3
safety v
replacing
cable-management arm 19
customer-replaceable unit (CRU) part
numbers 17
inner slide rails 21
keyboard 25
outer slide rails 21
slide rails 21
27
48
O
outer slide rails, replacing
21
© Copyright IBM Corp. 2004
51
52
IBM 17″ 1 U Flat Panel Monitor Console Kit: Installation and Maintenance Guide
Part Number: 02R2779
Printed in USA
(1P) P/N: 02R2779
">