IBM
Netfinity Rack Keyboard Tray Installation Instructions
For more information about this option, refer to the IBM Netfinity Rack Configurator program and the IBM
Netfinity Rack Planning and Installation Guide.
Before you begin, read through these instructions to familiarize yourself with the installation procedure.
This option consists of:
One keyboard tray
Two keyboard-tray support slides
One keyboard 8-ft extension cable
One mouse 8-ft extension cable
Eight cage nuts
Eight screws
Two cable ties
Two cable clamps
IBM Netfinity Rack Keyboard Tray Installation Instructions (this booklet)
You will need a screwdriver to install the keyboard tray.
1. Decide at what U level you want to install the keyboard tray.
Note: All vertical rack measurements are given in rack units (U). One U is equal to 4.45 cm (1.75
in.). The U levels are marked on labels on one front mounting rail and one rear mounting rail.
2. Install two cage nuts on each front mounting rail. The cage nuts go toward the inside of the rack.
Install cage nuts
in these holes.
a.
b.
c.
d.
Hook one side of the cage-nut clip into the rack-mounting-rail square hole.
Hold the cage nut in place and compress the cage-nut clip with a flat screwdriver blade.
With the cage-nut clip compressed, push the cage-nut clip into the square hole.
Release the screwdriver pressure on the clip. The cage nut is now locked in the square hole.
3. Repeat step 2 for the rear mounting rails.
4. Remove the keyboard-tray support slides from the keyboard-tray assembly.
a. Move one support slide toward the rear of the keyboard tray.
b. When the support slide comes to a stop:
1) Push the release lever on the inside of the support slide.
IBM is a trademark of the International Business Machines Corporation.
1
2) Continue moving the support slide until it comes off the keyboard-tray assembly.
5. Repeat step 4 on page 1 for the other keyboard-tray support slide.
6. Screw the support slides to the rack mounting rails.
a. Line up the mounting holes in one keyboard-tray support slide with the cage nuts.
b. Loosely thread four screws into the cage nuts.
c. Tighten the four screws.
d. Repeat steps 6a through 6c for the other keyboard-tray support slide.
7. Hold the keyboard tray even with the keyboard-tray support slides.
8. Carefully engage the keyboard-tray slides in the support slides and push the tray in until it closes.
9. Slide the tray in and out several times to check for smooth operation.
You can now install the keyboard and mouse on the tray.
2
Keyboard Tray
Product Warranty
The following is the statement of limited warranty for the United States, Canada, and Puerto Rico.
International Business Machines Corporation
Armonk, New York, 10504
Statement of Limited Warranty
The warranties provided by IBM in this Statement of Limited Warranty apply only to Machines you originally purchase for your use,
and not for resale, from IBM or your reseller. The term “Machine” means an IBM machine, its features, conversions, upgrades,
elements, or accessories, or any combination of them. Unless IBM specifies otherwise, the following warranties apply only in the
country where you acquire the Machine. If you have any questions, contact IBM or your reseller.
Machine: IBM Netfinity Rack Keyboard Tray
Warranty Period*: Three Years
*Contact your place of purchase for warranty service information.
Production Status
Each Machine is manufactured from new parts, or new and used parts. In some cases, the Machine may not be new and may have
been previously installed. Regardless of the Machine's production status, IBM's warranty terms apply.
The IBM Warranty for Machines
IBM warrants that each Machine 1) is free from defects in materials and workmanship and 2) conforms to IBM's Official Published
Specifications. The warranty period for a Machine is a specified, fixed period commencing on its Date of Installation. The date on
your receipt is the Date of Installation, unless IBM or your reseller informs you otherwise.
During the warranty period IBM or your reseller, if authorized by IBM, will provide warranty service under the type of service
designated for the Machine and will manage and install engineering changes that apply to the Machine.
For IBM or your reseller to provide warranty service for a feature, conversion, or upgrade, IBM or your reseller may require that the
Machine on which it is installed be 1) for certain Machines, the designated, serial-numbered Machine and 2) at an
engineering-change level compatible with the feature, conversion, or upgrade. Many of these transactions involve the removal of
parts and their return to IBM. You represent that all removed parts are genuine and unaltered. A part that replaces a removed part
will assume the warranty service status of the replaced part.
If a Machine does not function as warranted during the warranty period, IBM or your reseller will repair it or replace it with one that is
at least functionally equivalent, without charge. The replacement may not be new, but will be in good working order. If IBM or your
reseller is unable to repair or replace the Machine, you may return it to your place of purchase and your money will be refunded.
If you transfer a Machine to another user, warranty service is available to that user for the remainder of the warranty period. You
should give your proof of purchase and this Statement to that user. However, for Machines which have a life-time warranty, this
warranty is not transferable.
Warranty Service
To obtain warranty service for the Machine, you should contact your reseller or call IBM. In the United States, call IBM at
1-800-772-2227. In Canada, call IBM at 1-800-565-3344. You may be required to present proof of purchase.
IBM or your reseller will provide certain types of repair and exchange service, either at your location or at IBM's or your reseller's
service center, to restore a Machine to good working order.
When a type of service involves the exchange of a Machine or part, the item IBM or your reseller replaces becomes its property and
the replacement becomes yours. You represent that all removed items are genuine and unaltered. The replacement may not be
new, but will be in good working order and at least functionally equivalent to the item replaced. The replacement assumes the
warranty service status of the replaced item. Before IBM or your reseller exchanges a Machine or part, you agree to remove all
features, parts, options, alterations, and attachments not under warranty service. You also agree to ensure that the Machine is free
of any legal obligations or restrictions that prevent its exchange.
You agree to:
1. obtain authorization from the owner to have IBM or your reseller service a Machine that you do not own; and
2. where applicable, before service is provided —
a. follow the problem determination, problem analysis, and service request procedures that IBM or your reseller provide,
b. secure all programs, data, and funds contained in a Machine, and
c. inform IBM or your reseller of changes in a Machine's location.
3
IBM is responsible for loss of, or damage to, your Machine while it is 1) in IBM's possession or 2) in transit in those cases where IBM
is responsible for the transportation charges.
Extent of Warranty
IBM does not warrant uninterrupted or error-free operation of a Machine.
The warranties may be voided by misuse, accident, modification, unsuitable physical or operating environment, improper
maintenance by you, removal or alteration of Machine or parts identification labels, or failure caused by a product for which IBM is
not responsible.
THESE WARRANTIES REPLACE ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. THESE WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS AND
YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM JURISDICTION TO JURISDICTION. SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF EXPRESS OR IMPLIED WARRANTIES,
SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU. IN THAT EVENT SUCH WARRANTIES
ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES APPLY AFTER THAT PERIOD.
Limitation of Liability
Circumstances may arise where, because of a default on IBM's part or other liability you are entitled to recover damages from IBM.
In each such instance, regardless of the basis on which you are entitled to claim damages from IBM (including fundamental breach,
negligence, misrepresentation, or other contract or tort claim), IBM is liable only for:
1. damages for bodily injury (including death) and damage to real property and tangible personal property; and
2. the amount of any other actual direct damages or loss, up to the greater of U.S. $100,000 or the charges (if recurring, 12
months' charges apply) for the Machine that is the subject of the claim.
UNDER NO CIRCUMSTANCES IS IBM LIABLE FOR ANY OF THE FOLLOWING: 1) THIRD-PARTY CLAIMS
AGAINST YOU FOR LOSSES OR DAMAGES (OTHER THAN THOSE UNDER THE FIRST ITEM LISTED ABOVE);
2) LOSS OF, OR DAMAGE TO, YOUR RECORDS OR DATA; OR 3) SPECIAL, INCIDENTAL, OR INDIRECT
DAMAGES OR FOR ANY ECONOMIC CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS OR SAVINGS),
EVEN IF IBM OR YOUR RESELLER IS INFORMED OF THEIR POSSIBILITY. SOME JURISDICTIONS DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU.
30F6976
Printed in the U.S.A.
Copyright International Business Machines Corporation 1997. All rights reserved.
Note to U.S. Government Users — Documentation related to restricted rights — Use, duplication or
disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corp.
4
Keyboard Tray
">
